University of Ottawa

School of Information Technology and Engineering

(SITE)

Introductory
Electronics Laboratory

Prepared for

Engineering Summer School

Summer 2005

© Salim Y. Said
1
 Morning Session
Purpose

The purpose of this session is to get familiar with the electronics lab. We will
discover resistors, capacitors, and operational amplifiers. We will also learn how
to use the breadboard, power supplies, multi- meters, function generator, and the
oscilloscope.

Resistors

A resistor is a two-terminal electrical component that creates an electrical

potential difference across its terminals that is proportional to the current passing
through it. The ratio of potential difference (also called voltage) to current is
known as its electrical resistance (or simply resistance). In SI units, the resistance
is measured in ohms (O).

Figure 1: A Resistor

Colour 1st Band 2nd Band 3rd Band 4th Band

(multiplier) (tolerance)
Black 0 0 x 100
Brown 1 1 x 101 ± 1%
Red 2 2 x 102 ± 2%
Orange 3 3 x 103
Yellow 4 4 x 104
Green 5 5 x 105 ± 0.5%
Blue 6 6 x 106 ± 0.25%
Violet 7 7 x 107 ± 0.1%
Gray 8 8 x 108 ± 0.05%
White 9 9 x 109
Gold x 0.1 ± 5%
Silver x 0.01 ± 10%

Question: Can you read the value of the resistor in figure 1?

2
Capacitors

The capacitor's capacitance (C) is a measure of the amount of charge (Q) stored
on each plate for a given potential difference or voltage (V) which appears across
the plates. In SI units, a capacitor has a capacitance is measured in farad (F).

Figure 2: different capacitor models

Operational Amplifiers

An amplifier is a device that uses a small amount of energy to control a larger

amount. The relationship of the input to the output--usually expressed as a
function of the input frequency--is called the transfer function of the amplifier,
and the magnitude of the transfer function is termed the gain. Amplifiers are
typically utilized over a specific range of frequencies and are generally of
maximal utility if the gain is constant in that range.

Figure 3: 741 Operational Amplifier

3
Breadboard

A breadboard is a material or a device used to build a prototype of an electronic

circuit.

Figure 4: Breadboard

The breadboard has many strips of metal (copper usually) which run underneath
the board. The metal strips are laid out as shown in figure 5.

Figure 5: Breadboard Metallic Strips

These strips connect the holes on the top of the board. This makes it easy to
connect components together to build circuits. To use the bread board, the legs of
components are placed in the holes (the sockets). The holes are made so that they
will hold the component in place. Each hole is connected to one of the metal
strips running underneath the board.

The long top and bottom row of holes are usually used for power supply
connections.

4
Power Supply

A power supply is a separate unit or part of a circuit that supplies power to the
rest of the circuit or to a system. The power supply takes the current from your
wall electrical socket and coverts it into the various voltages your circuit needs.

Figure 6: Power Supply

Multimeter

A meter is a measuring instrument. An ammeter measures current, a voltmeter

measures the potential difference (voltage) between two points, and an ohmmeter
measures resistance. A multimeter combines these functions and possibly some
additional ones as well, into a single instrument.

Figure 7: Multimeter

5
 Before you turn the power supply, let the lab demonstrator check your circuit.
Not doing so, may cause damage to the components or equipment!!

Practice 1
Build up the circuit as shown in figure 8. R1 = O and R2 = O. Measure using the
multi- meter the values of the current I, and the voltages across R1 and R2
respectively.

• Is V = V1 + V2 ?
V1 V2
- + -
+

R1 R2

+
5
V - Vs

Figure 8: Resistors in Series

Build up the circuit as shown in figure 9. R1 = O and R2 = O. Measure using the

multi- meter the values of the current I, and the voltages across R1 and R2
respectively. Also measure the currents following through the resistors, I1 and I2 .

• Is I = I1 + I2 ?
• Can you find a relationship between V, V1 , and V2 ?

I I1 I2

+ + +

5V
V1 R1 V2 R2
- Vs

- -

Figure 9: Resistors in Parallel

6
 In order to perform the practice exercise #2, you need to get familiar with use of
the function generator and the oscilloscope. Please listen to the lab demonstrator
instructions and explanations before performing the exercise.

Practice 2

Set the function generator to produce a 5 kHz sine wave with amplitude of 2 volts
(one peak only). Connect the output of the function generator to the inputs of the
oscilloscope. Tune the oscilloscope so that you may clearly see the waveform.
Identify the peak-to-peak amplitude, the period, and the frequency of the
waveform. Change the waveform shape to triangle and square waves.

Function Generator

A function generator is a device that can produce various patterns of voltage at a

variety of frequencies and amplitudes. It is used to test the response of circuits to
common input signals. The electrical leads from the device are attached to the
ground and signal input terminals of the device under test.

Figure 10: Simple Function Generator

Most function generators allow the user to choose the shape of the output from a
small number of options.

• Square wave - The signal goes directly from high to low voltage.
• Sine wave - The signal curves like a sinusoid from high to low voltage.
• Triangle wave - The signal goes from high to low voltage at a fixed rate.

The amplitude control on a function generator varies the voltage difference

between the high and low voltage of the output signal. The frequency control of a
function generator controls the rate at which output signal oscillates.

7
Oscilloscope >>> http://www.doctronics.co.uk/scope.htm#screen

An oscilloscope is easily the most useful instrument available for testing circuits
because it allows you to see the signals at different points in the circuit. The best
way of investigating an electronic system is to monitor signals at the input and
output of each system block, checking that each block is operating as expected
and is correctly linked to the next. With a little practice, you will be able to find
and correct faults quickly and accurately.

Figure 11: Oscilloscope

As you can see, the screen of this oscilloscope has 8 squares or divisions on the
vertical axis, and 10 squares or divisions on the horizontal axis. Usually, these
squares are 1 cm in each direction:

Figure 12: Oscilloscope Display

8
 Afternoon Session

Objective

The objective of this session is to use all the knowledge and skills learned in the
morning session to build a signal generator than can produce a square wave using
741 operational amplifiers.

Square Wave Generator

One simple and inexpensive circuit used to generate a square-wave is the

relaxation oscillator circuit. It is also known as the “a stable multi- vibrator”.

Figure 13: Simple Square wave Generator Circuit

Before you turn the power supply, let the lab demonstrator check your circuit.
Not doing so, may cause damage to the components or equipment!!

Connect the circuit shown in figure 13, with the following resistor/capacitor
values:

• R1 = 10 K O
• R2 = 12 K O
• Rf = 500K O to 50O
• C = 0.1µF

9
Note that the value of Vcc = 15V and Vin = 0V (grounded).

Before you turn the power supply, let the lab demonstrator check your circuit.
Not doing so, may cause damage to the components or equipment!!

Using the oscilloscope, display Vo on channel 1 screen. Record the peak-to-peak

amplitude, the period, and the frequency of the waveform.

10
Circuit Analysis

• Time constant τ = Rf C
R1
• Vn = Vcc .
R1 + R2

Let Vo = Vcc. Vc will increase toward positive Vcc with a time constant τ. When
Vc exceeds Vn , Vo will change to negative Vcc. In other words, the amplifier will
flip from saturating in the positive direction to saturating in the negative direction.
In a similar manner, Vc will charge toward negative Vcc until it falls below -Vn .
As a result of this positive and negative charging, a square wave will be generated
varying between ± Vcc.

Consider now the analysis of Vc. The waveform of Vc is that of ± Vn exponential

charging saw tooth. Consider the half period as Vc charges from –Vn to + Vn .

Vc = -Vn + (Vcc – (-Vn ))(1 – e –t / Rf C )

When Vc = Vn , t= T /2

è Vn = -Vn + Vcc + Vn – (Vcc + Vn )e –T / 2RC

V − Vn  V − Vn 
è cc = e –T / 2RC è T = 2RC ln  cc 
Vcc + Vn  Vcc + Vn 
R1
But Vn = Vcc
R1 + R2
−1
 2R  1   2R 1  
è T = 2RC ln 1 + 1  èf= =  2RC ln 1 +  
 R2  T   R 2 

The following are the corresponding waveforms of the generated square wave and
the Vn exponential saw tooth curves.

VOLT
S
+V

+V

t
T/2

11