I2C EEPROM's PDF
I2C EEPROM's PDF
24AA014/24LC014 24C01C
24AA02/24LC02B 24C02C
24AA024/24LC024 24AA025/24LC025
24AA04/24LC04B 24AA08/24LC08B
24AA16/24LC16B 24AA32A/24LC32A
24AA64/24LC64 24AA128/24LC128/24FC128
24AA256/24LC256/24FC256 24AA512/24LC512/24FC512
Package Types(1)
PDIP/SOIC TSSOP/MSOP(2) TSSOP SOT-23-5
(24XX00)
A0 1 14 VCC
A0 1 8 VCC A0 1 8 VCC A1 2 13 WP
SCL 1 5 VCC
A1 2 7 WP(3) A1 2 7 WP(3) NC 3 12 NC
NC 4 11 NC 2
A2 3 6 SCL A2 3 6 5 10 VSS
SCL NC NC
A2 6 9 SCL
VSS 4 5 SDA VSS 4 5 SDA SDA 3 4 NC
VSS 7 8 SDA
SOT-23-5 Note 1: Pins A0, A1, A2 and WP are not used by some
DFN
(all except 24XX00) devices (no internal connections). See Table 1-1,
A0 1 8 VCC Device Selection Table, for details.
SCL 1 5 WP A1 2 7 WP(3) 2: Pins A0 and A1 are no-connects for the 24XX128
A2 3 6 SCL and 24XX256 MSOP devices.
VSS 2
VSS 4 5 SDA 3: Pin 7 is “not used” for 24XX00, 24XX025 and
SDA 3 4 VCC 24C01C.
*24XX is used in this document as a generic part number for 24 series devices in this data sheet. 24XX64, for example,
represents all voltages of the 64 Kbit device.
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to
the device. This is a stress rating only and functional operation of the device at those or any other conditions
above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating
conditions for extended periods may affect device reliability.
All Parameters apply across all Commercial (C): TA = 0°C to +70°C, VCC = 1.8V to 5.5V
recommended operating ranges Industrial (I): TA = -40°C to +85°C, VCC = 1.8V to 5.5V
unless otherwise noted Automotive (E): TA = -40°C to +125°C, VCC = 4.5V to 5.5V
5 4
2 D4
SCL
7
3 8 9 10
SDA
6
IN
16
13 14
SDA
OUT
(protected)
WP 11 12
(unprotected)
3.1 A0, A1, A2 Chip Address Inputs 3.3 Serial Clock (SCL)
The A0, A1 and A2 pins are not used by the 24XX01 This input is used to synchronize the data transfer to
through 24XX16 devices. and from the device.
The A0, A1 and A2 inputs are used by the 24C01C,
24C02C, 24XX014, 24XX024, 24XX025 and the
3.4 Write-Protect (WP)
24XX32 through 24XX512 for multiple device opera- This pin must be connected to either VSS or VCC. If tied
tions. The levels on these inputs are compared with the to VSS, write operations are enabled. If tied to VCC,
corresponding bits in the slave address. The chip is write operations are inhibited but read operations are
selected if the compare is true. not affected. See Table 1-1 for the write-protect
For the 24XX128 and 24XX256 in the MSOP package scheme of each device.
only, pins A0 and A1 are not connected.
Up to eight devices (two for the 24XX128 and 3.5 Power Supply (VCC)
24XX256 MSOP package) may be connected to the A VCC threshold detect circuit is employed which
same bus by using different Chip Select bit disables the internal erase/write logic if VCC is below
combinations. 1.5V at nominal conditions. For the 24C00, 24C01C
In most applications, the chip address inputs A0, A1 and 24C02C devices, the erase/write logic is disabled
and A2 are hard-wired to logic ‘0’ or logic ‘1’. For below 3.8V at nominal conditions.
applications in which these pins are controlled by a
microcontroller or other programmable device, the chip
address pins must be driven to logic ‘0’ or logic ‘1’
before normal device operation can proceed.
Block Diagram
A0*A1*A2* WP* HV Generator
I/O
SCL
YDEC
SDA
VCC
VSS Sense Amp.
R/W Control
* A0, A1, A2, WP and page latches are not used by some
devices.
See Table 1-1, Device Selection Table, for details.
SDA
SCL 1 2 3 4 5 6 7 8 9 1 2 3
Transmitter must release the SDA line at this point, Receiver must release the SDA line
allowing the Receiver to pull the SDA line low to at this point so the Transmitter can
acknowledge the previous eight bits of data. continue sending data.
SDA Line S P
A A A
Bus Activity C C C
K K K
Bus Activity A A A A
C C C C
K K K K
Did Device No
Acknowledge
(ACK = 0)?
Yes
Next
Operation
S S
Bus Activity T Control Address T Control Data S
Master A Byte Byte (n) A Byte Byte T
R R O
T T P
S S P
SDA Line
A A A N
C C C O
K K K
Bus Activity A
C
K
SDA Line P
A A A A N
C C C C O
Bus Activity K K K K A
C
K
Note: For very small packages with no room for the Pb-free JEDEC designator
e3 , the marking will only appear on the outer carton or reel label.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
Note: Please visit www.microchip.com/Pbfree for the latest information on Pb-free conversion.
Note: For very small packages with no room for the Pb-free JEDEC designator
e3 , the marking will only appear on the outer carton or reel label.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
Note: Please visit www.microchip.com/Pbfree for the latest information on Pb-free conversion.
XXX 244
YWW 506
NN L7
Note: For very small packages with no room for the Pb-free JEDEC designator
e3 , the marking will only appear on the outer carton or reel label.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
Note: For very small packages with no room for the Pb-free JEDEC designator
e3 , the marking will only appear on the outer carton or reel label.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
XXNN 5EL7
Note: For very small packages with no room for the Pb-free JEDEC designator
e3 , the marking will only appear on the outer carton or reel label.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
XXXXXXT 4L8BI
YWWNNN 2281L7
Note: For very small packages with no room for the Pb-free JEDEC designator
e3 , the marking will only appear on the outer carton or reel label.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
XXXX 4L08
TYWW I228
NNN 1L7
Note: For very small packages with no room for the Pb-free JEDEC designator
e3 , the marking will only appear on the outer carton or reel label.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
XXXXXXXT 4A256I
YYWW 0528
NNN 1L7
Note: For very small packages with no room for the Pb-free JEDEC designator
e3 , the marking will only appear on the outer carton or reel label.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
E1
n 1
A A2
L
c
A1
β B1
p
eB B
E1
D
2
B n 1
h α
45°
c
A A2
φ
β L A1
p
D b
n
L
E E2
EXPOSED
METAL 2 1
PIN 1 PAD
ID INDEX
D2
AREA
(NOTE 2) BOTTOM VIEW
TOP VIEW
A
A3 A1
EXPOSED
TIE BAR
(NOTE 1)
E1
p
B
p1 D
n 1
c
A A2
φ A1
L
β
E1
D
2
B
n 1
A A2
c
φ
A1
(F) L
β
E1
D
2
1
n
B
α
A
φ A1 A2
β
L
E1
2
n 1
B
α
A
β A1 A2
L
From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________ FAX: (______) _________ - _________
Application (optional):
Would you like a reply? Y N
Questions:
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
Note 1: Most products manufactured after January 2005 have a Matte Tin (Pb-free) finish.
Most products manufactured before January 2005 have a finish of approximately 63% Sn and 37% Pb (Sn/Pb).
Please visit www.microchip.com/Pbfree for the latest information on Pb-free conversion, including conversion date codes.
Sales and Support
Data Sheets
Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recom-
mended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following:
Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using.
• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
• Microchip is willing to work with the customer who is concerned about the integrity of their code.
• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
04/20/05