Scribd
Upload
105 views

Types of Earthing (As Per IEC Standards)

There are three main types of earthing arrangements as defined by IEC standards: TN, TT, and IT. The TN system uses a single-point earth connection at the source. There are three sub-types of TN depending on whether the protective earth (PE) and neutral conductors are combined. The TT system uses a local earth connection at the customer premises rather than relying on the source. The IT system uses little to no direct connection of equipment to earth. Country standards may adopt or modify these three main types, such as the UK using a form of TN-C-S and France/Japan/Denmark commonly using TT earthing.

Uploaded by

visakhgs
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
105 views

Types of Earthing (As Per IEC Standards)

There are three main types of earthing arrangements as defined by IEC standards: TN, TT, and IT. The TN system uses a single-point earth connection at the source. There are three sub-types of TN depending on whether the protective earth (PE) and neutral conductors are combined. The TT system uses a local earth connection at the customer premises rather than relying on the source. The IT system uses little to no direct connection of equipment to earth. Country standards may adopt or modify these three main types, such as the UK using a form of TN-C-S and France/Japan/Denmark commonly using TT earthing.

Uploaded by

visakhgs
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 7

Types of Earthing (as per IEC Standards)

SEA (SYSTEM EARTHING ARRANGEMENT)

Introduction

In the preceding article we studied the basics of Earthing and also the basic most Earthing
type where the neutral is grounded at source and optionally grounding is done even at
customer side.

Besides this, International Standard – IEC 60364 formally defines different types of
Earthing arrangements. Let us examine them here in detail.

IEC Standard for Earthing

IEC Standard 60364 specifies a Two Letter Codes to identify type of earthing. It also
defines three families of Earthing arrangements.

 The two letter code is based on Source Side – Device Side Earthing.
 The First Letter indicates how the Earthing is done on Source side (Generator /
Transformer).
 The Second Letter indicates how the Earthing is done on Device side (place
where electricity is consumed at customer premises).

The Letters used are as follows:

T – (French word “Terre” meaning Earth) – It means direct connection of a point to earth

I – It means that either no point is connected to Earth or it is connected via high


impedance

N – It means that there is direct connection to neutral at the source of installation which is
in turn connected to the ground

Based on a combination of these three letters, there are three families of Earthing
arrangements proposed by IEC as below:

 TN Network
 TT Network
 IT Network
A. TN Network

In TN type of earthing system, one of the points of the source side (Generator or
Transformer) is connected to earth. This point is usually the star point in a three phase
system. The body of the connected electrical device is connected to earth via this earth
point on the source side. See fig. below which depicts this:

In above diagram:

PE – Acronym for “Protective Earth” – is the conductor that connects the exposed
metallic parts of the consumer’s electrical installation to the ground.

N –Also called Neutral. It is the conductor that connects Star point in a 3 phase system to
the earth.

There are three sub-types of TN networks as below:

1. TN-S
2. TN-C
3. TN-C-S
TN-S: In this, separate conductors for Protective Earth (PE) and Neutral run from
Consumer’s electrical installation till the source. They are connected together only at the
power source.
TN-C: In this, there is a combined conductor called PEN (Protective Earth-Neutral)
which is connected to earth at the source.
TN-C-S: In this type of earthing, part of the system uses a combined PEN conductor for
earthing, whereas for remaining part of the system uses separate conductor for PE and N.

Usually, the combined PEN conductor is used near the source of the system.
B. TT Network

In TT type of earthing system, consumer employs its own local earth connection in the
premises, which is independent of any earth connection at source side.

This type of earthing is preferred in telecommunication applications, because this system


is free of any high or low frequency noise that comes through neutral wire connected to
the equipment.
C. IT Network

In IT type of earthing system, there is either no connection to earth at all, or it is done via
a high impendence earthing connection.

Country Specific Earthing Standards

UK – Uses Protective Multiple Earthing (PME) – which is a form of TN-C-S type of


earthing

Australia / New Zealand – Also uses TN-C-S type of earthing know as Multiple Earth
Neutral (MEN) system

USA / Canada – Uses TN-C for the feed from Transformer but uses TN-C-S within the
structure at customer premises

France / Japan / Denmark – Uses TT type of earthing and customer must make its own
arrangement for its own earthing connection

You might also like