3/15/2018 The Basics of Tuning PID Loops | CrossCo

Home (/) /  Process Control Integration (/process-controls) /  Blog (/blog/process-control-integration) /  The Basics of Tuning PID Loops

PROCESS CONTROLS (/CATEGORIES/PROCESS-CONTROL S )

AUTOMATION (/CATEGORIES/AUTOMATION)

The Basics of Tuning PID Loops

Chris Hardy | April 9th, 2014

The art of tuning a PID loop is to have it adjust its OP to move the PV as quickly as possible to the SP (responsive), minimize overshoot, and then
hold the PV steady at the SP without excessive OP changes (stable).

First, Some Definitions

PID = Proportional, Integral, Derivative algorithm. This is not a P&ID, which is a Piping (or Process) and Instrumentation Diagram.
PV = Process Variable - a quantity used as a feedback, typically measured by an instrument. Also sometimes called "MV" - Measured Value.
SP = SetPoint - the desired value for the PV.
OP = OutPut - a signal to a device that can change the PV - frequently a valve, damper, or a pump speed reference. Also sometimes called
"CV" - Controlled Value.
Overshoot = when the PV moves further past the SP than desired. 
A PID loop in manual (as opposed to automatic) only changes its OP upon operator request.
A loop in remote has its SP automatically adjusted by external logic. In local the SP is only changed by the operator. Some systems combine
auto and remote into “cascade” mode.
A direct acting PID loop increases its OP in response to increasing PV, while a reverse acting loop decreases its OP. “Normal” loops are
reverse acting. Loops controlling level or pressure via a valve on an output, or temperature via cooling are generally direct acting –
“backwards” loops.
Error = the difference between PV and SP.

Overshoot

3 Basic Tuning Parameters of a PID Loop

Note: for demonstration purposes the charts below show the individual responses of the actions where the PV is NOT affected by the OP. Normally
the PV would be affected by the change in OP & would therefore be brought back toward the SP as a result of the OP's response.

Gain:
Also called proportional band or P-gain, the gain determines how much change the OP will make due to a change in error (from a PV change and /
or an SP change). This mainly corrects the OP based on upsets as they happen. "Gain" implies that a larger number will have more effect.
"Proportional band" implies the opposite. P-Gain = 100% / P-band.

https://www.crossco.com/blog/basics-tuning-pid-loops 1/7
3/15/2018 The Basics of Tuning PID Loops | CrossCo

Gain Only Response

Reset:
Also called integral or I-gain, the reset determines how much to change the OP over time due to the error (regardless of the direction of movement
of the error). This brings a stable PV that is off SP toward the SP. Reset or I-gain implies that a larger number will have more effect. Integral implies
the opposite. Reset [resets per minute] = 60 / Integral [seconds per reset].

Reset Only Response

Preact: 
Also called derivative or D-gain, the preact determines how much to change the OP due from a change in direction of the error or PV. While acting
on the PV, rather than the error, is an option in some loops, acting on PV is better because it is undesirable to bump the OP when the SP is
changed. It is called preact because it allows the loop to “anticipate” upsets as they begin to happen and react quickly.

Preact Only Response

Actions Working Together:

When the PV is approaching the SP, Proportional and Integral work in opposite directions to cause the PV of a properly tuned loop to get to the SP
quickly without excessively overshooting. For a typical reverse-acting loop, the proportional will try to close the OP as the PV rises toward the SP,
but the integral will try to open the OP because PV is below SP. As the PV gets closer to the SP, integral action decreases resulting in the PV
smoothly decelerating into the SP.

Gain and Reset Together

Initial Loop Tuning

The goal of tuning a PID loop is to make it stable, responsive and to minimize overshooting. These goals - especially the last two - conflict with
each other. You must find a compromise between the goals which acceptably satisfies them all. Process requirements and physical limitations will
determine the balance between amount of acceptable overshoot as well as the demand for responsiveness. The primary factors which dictate the
limits to responsiveness of a loop are:

1. The amount of PV change resulting from an OP step change.

2. The time from when the OP changes until the change starts to be seen in the PV,
3. The time for the PV to reach its new level. Because the PV usually approaches its new level asymptotically, for that time constant we
frequently use the time it takes the system's step response to reach 1-1/e, or about 63% of the distance from the initial to its final value.

https://www.crossco.com/blog/basics-tuning-pid-loops 2/7
3/15/2018 The Basics of Tuning PID Loops | CrossCo

Three Response Factors

When beginning to tune a loop, first make sure you have a good trending package. Watch the PV, SP, OP and other outside variables you suspect
might influence the PV together. Characterize the loop by making step changes in manual through the range of the OP and back, and make a note
of these three factors. Stepping through the range in both directions is valuable to quantify the linearity and hysteresis of the system.

Linearity: If the same change in OP through the whole scale results in a similar change in PV at each point, the system is linear. But if a change on
one part of the OP range results in more PV change than the same OP change in a different range, the system is non-linear. 

Linear OP

Non-Linear OP

Hysteresis: Some devices will yield a different PV for the same OP depending on whether the OP went up or down to get there. A valve might allow
25 GPM through after moving from 20% to 30%, but 30 GPM after moving from 40% to 30%.

OP Hysteresis

DOWNLOAD THE(/NODE/2760)
JACK DANIEL'S CASE STUDY

2 Basic PV Categories: Particle and Bulk

Particle properties are those where a fluid in a pipe may have different properties in different areas, so that the fluid must be mixed or moved to
change the property at the PV measurement point. Particle properties include temperature, pH, conductivity, etc. These tend to have a significant
delay between a change in OP and the beginning of the change in PV (#2 above), and therefore might benefit from derivative action.

Bulk properties describe the state of the fluid as a whole so that it all changes everywhere in a pipe or vessel (for practical purposes)
simultaneously. Examples: flow, level, and pressure. Generally these PVs begin to show the result of an OP change immediately (even if the time
constant to complete the change is long) and do not need any derivative.

Another categorization of PVs: some (such as flow) increase when the OP increases and decrease when the OP decreases. These should be
characterized as shown above - they typically need more integral and minimal P-gain. For others (such as level) the direction (rather than value) of
the PV is relative to the OP. For the latter, a characterization is more subtle - you want to characterize the slope of the PV for various OPs instead of
its value. These sometimes need moderate-to-high gain and less integral.

Starting Parameters
https://www.crossco.com/blog/basics-tuning-pid-loops 3/7
3/15/2018 The Basics of Tuning PID Loops | CrossCo

Loops where the PV changes quickly due to a change in OP (flow, or pressure or level in vessels with fast turnover) should have low P-gain
(perhaps 0.2) and higher reset (1.5 – 10 rpm). Loops where the PV changes slowly, or changes its direction of movement due to change in OP
(temperature and level in vessels with slow turnover) typically need high gain (3 – 100) and low reset (0.05 – 0.3). 

These recommended starting parameters are based on the input and output ranges being the same. Some controllers handle tuning parameters
based on percent of span, while others do not make this correction. If the spans are different, corrections would have to be made to the parameters
themselves. For example, if the flow through a pipe can be from 0 – 10,000 gpm, and you are adjusting the speed of a VFD from 0-100%, the
starting gain and reset would need to be 0.004 and 0.02 instead of 0.4 and 2.0.

There are numeric methods where the natural resonant frequency of a system is determined and parameters set accordingly, but I've found an
iterative, intuitive approach to be more useful:

Start with a low proportional and no integral or derivative.

Double the proportional until it begins to oscillate, then halve it.
Implement a small integral.
Double the integral until it starts oscillating, then halve it.

That will get the constants close to where they need to be for fine adjustment. Don’t hesitate to put the loop back in manual if the loop goes crazy
or while studying the trend.

Fine Tuning
To achieve the goal of a responsive and stable loop with minimal overshoot, the tuning must be tested in response to upsets and at steady state.
Upsets can be induced by:

Changing the SP.

Putting the loop in manual, changing the OP, then returning to automatic.
Externally causing a change to the PV.

Once the PV has stabilized at its SP, upset it by stepping the SP. Even a very small change is useful here. The proportional will cause an immediate
jump in OP, then the integral will cause the OP to continue ramping in the same direction. When the PV starts to move, the proportional will cause
the OP to move back the other way, and the integral action will diminish as the PV approaches the SP. Overshoot is often caused by too much
integral and/or not enough proportional.

Too Much Reset

The OP needs to start moving back the other way well before the PV reaches the SP. The amount of time between the peak and the PV hitting the
SP depends on the nature of the loop. If the peak comes too late, you need more proportional or less integral. If the peak comes too early, you
need less proportional or more integral. An early peak will result in the PV leveling out before it reaches the SP, causing the OP and PV to swing on
the way to their new steady-state values.

Swinging to SP

Once the loop is roughly tuned, put it in manual and change either the SP or OP, let it stabilize, then put it back in automatic. The loop will then
move the PV to the SP, but with integral only - without the initial OP pulse from proportional. If the OP moves too slowly, you need more integral. A
long delay between the change in OP and the end of the resulting change to PV dictates a lower integral value. Introduce derivative if you see that
a bump in OP would be beneficial when the PV changes direction at the beginning of an upset.

This is an iterative method – every change in one parameter changes the ideal value for the other parameters. Go back and forth between
upset methods and steady state stability, and make sure you check the tuning for the full range of possible SPs, If the system is non-linear (see
above), a loop that is stable at higher flows may swing wildly at lower flows, and a loop that is responsive at low flows may be sluggish at higher
flows. A (http://innovativecontrols.com/blog/advanced-pid-loop-tuning-methods?
utm_source=blog&utm_medium=internal%20referral&utm_content=chris%20hardy&utm_campaign=from%20PID%20basics) PID loop with a control
deadband can sometimes achieve acceptable control despite this challenge. See other ways to deal with valves and dampers with deadband in
"Advanced PID Loop Tuning Methods."

(/NODE/202)
READ "ADVANCED PID LOOP TUNING METHODS"

https://www.crossco.com/blog/basics-tuning-pid-loops 4/7
3/15/2018 The Basics of Tuning PID Loops | CrossCo

Diagnosing the Cause of Oscillations

If the OP and PV peak at the same time, the oscillation is proportional-driven.

Too Much Gain

If the OP peaks when the PV is crossing its midpoint & visa versa (so that the PV and OP waves are 90° out of phase), the oscillation is integral-
driven. Some oscillations are driven by other factors in the system - put the loop in manual to see if it continues to oscillate if you suspect the loop
you are tuning is not causing the oscillation.

Too Much Reset

Sometimes oscillations are acceptable. For example, the goal of boiler drum level control is primarily to avoid tripping on either low or high level. A
moderate amount of oscillation at steady state is a good trade-off to get enough additional responsiveness to avoid tripping following significant
upsets.

Note that actuators (especially motorized valves) with deadband and/or limited duty cycle will ALWAYS swing when attached to a traditional PID
loop regardless of tuning parameters. You can tell this is happening by looking at the trend – the PV will be flat while the OP is ramping down (due
to integral), then the PV jumps to the other side of the SP, and the pattern reverses. See how to deal with valves and dampers with deadband in
"Advanced PID Loop Tuning Methods". (/node/202)

Limited Duty Deadband Oscillation

Balancing the Tuning Goals
A properly tuned loop balances the demands of stability, responsiveness and low overshoot. Tune the loop by adjusting the three tuning
parameters so that the loop responds well in a variety of upset and steady-state situations. Some "Advanced PID Tuning Methods (/node/202)" may
be necessary if challenges such as non-linearity, deadband, hysteresis or measurable external upsetting events prevent the loop from being
satisfactorily tuned with the basic methods described above.

(HTTP://CROSSISG.COM)
DISCOVER CROSS COMPANY

Related Upgrade from Iconics Genesis32 to Genesis64 (/automation/upgrade-iconics-genesis32-genesis64)

Posts Upgrade ICONICS Genesis32 Application to Genesis64
Save 50% on the cost of new software

Automation Solutions for High-Mix Manufacturing (/automation/automation-solutions-high-mix-manufacturing)

A high-mix plant produces many different parts, each of which has different processes that all require some human involvement. Any endeavor to
automate must take into account the non-value-add time associated with changeovers, or eliminate them entirely. With this in mind, here are three paths
possible to automate in a high-mix environment.

https://www.crossco.com/blog/basics-tuning-pid-loops 5/7