0000-00 15-3

1. ENGINE DATA LIST

Data Unit Value
Coolant temperature ℃ 0.436 V (130℃) to 4.896 V (-40℃)
Intake air temperature ℃ -40 to 130℃ (varies by ambient air
temperature or engine mode)
A/T 780 ± 20
Idle speed rpm
M/T 750 ± 20
Engine load % 18~25%
Mass air flow kg/h 16 to 25 kg/h
Throttle position angle °TA 0° (Full Open) to 78° (Close)
Engine torque Nm varies by engine conditions
Injection time ms 3 to 5ms
Battery voltage V 13.5 V to 14.1 V
Accelerator pedal position 1 V 04. to 4.8V
Accelerator pedal position 2 V 0.2 to 2.4 V
Throttle position 1 V 0.3 to 4.6 V
Throttle position 2 V 0.3 to 4.6 V
Oxygen sensor mV 0 to 5 V
A/C compressor switch 1=ON / 0=OFF -
Full load 1=ON / 0=OFF -
Gear selection (A/T) 1=ON / 0=OFF -
Knocking control 1=ON / 0=OFF -
Brake switch 1=ON / 0=OFF -
Cruise control 1=ON / 0=OFF -
15-4

1. MAJOR COMPONENT
Rear exhaust gas temp. Front exhaust gas temp.
sensor Injector (C3I) Oxygen sensor sensor

Camshaft position
sensor

Oil pressure
switch

Glow plug

Variable swirl valve Knock sensor (2) Electronic throttle T-MAP sensor
body (Temp.+Pres.)
 0000-00 15-5

Differential pres. GCU (Glow plug

Fuel temp. sensor sensor control unit) D20DTF ECU

Coolant temp. sensor

HFM (air
mass/temperature)

E-EGR Fuel rail pres. sensor

bypass valve E-EGR valve IMV
15-6

2. SYSTEM OPERATION
1) Input/Output of ECU
(1) ECU Block diagram
 0000-00 15-7

(2) Components for ECU Input

HFM sensor Crankshaft posi. Accel. pedal Throttle

sensor posi. sensor posi.sensor Knock sensor

Exhaust gas T-MAP sensor

temp. sensor

Oxygen
Differential sensor
pressure
sensor

E-EGR valve Camshaft posi. Coolant temp.

Fuel rail posi. sensor sensor sensor
pres.sensor

CAN
Swirl valve posi. - ABS&ESP
sensor - GCU
- Meter cluster
- TCU
- BCM
Oil pressure
switch Meter cluster
- Refrigerant pressure sensor
- Clutch pedal signal
- Blower switch signal
- Brake pedal signal
15-8

(3) Components for ECU Input

Start motor A/C Injector

Variable swirl compressor Throttle posi.
valve sensor

E-EGR valve IMV

E-EGR cooler E-VGT

bypass valve actuator

PTC heater Cooling fan

Engine room
relay box

CAN

- Glow plug unit

- ABS & ESP unit
- BCM
- E-coupling unit
- EPS
- GCU
- Meter cluster
- SKM
- TCU
- Self diagnosis
 0000-00 15-9

2) ECU Control
(1) Function
a. ECU Function
ECU receives and analyzes signals from various sensors and then modifies those signals into
permissible voltage levels and analyzes to control respective actuators.
ECU microprocessor calculates injection period and injection timing proper for engine piston speed and
crankshaft angle based on input data and stored specific map to control the engine power and emission
gas.
Output signal of the ECU microprocessor drives pressure control valve to control the rail pressure and
activates injector solenoid valve to control the fuel injection period and injection timing; so controls
various actuators in response to engine changes. Auxiliary function of ECU has adopted to reduce
emission gas, improve fuel economy and enhance safety, comforts and conveniences. For example,
there are EGR, booster pressure control, autocruise (export only) and immobilizer and adopted CAN
communication to exchange data among electrical systems (automatic T/M and brake system) in the
vehicle fluently. And Scanner can be used to diagnose vehicle status and defectives.
Operating temperature range of ECU is normally -40 to +85°C and protected from factors like oil,
water and electromagnetism and there should be no mechanical shocks.
To control the fuel volume precisely under repeated injections, high current should be applied instantly
so there is injector drive circuit in the ECU to generate necessary current during injector drive stages.
Current control circuit divides current applying time (injection time) into full-in-current-phase and hold-
current-phase and then the injectors should work very correctly under every working condition.

b. Control Function
- Controls by operating stages
To make optimum combustion under every operating stage, ECU should calculate proper injection
volume in each stage by considering various factors.
- Starting injection volume control
During initial starting, injecting fuel volume will be calculated by function of temperature and engine
cranking speed. Starting injection continues from when the ignition switch is turned to ignition
position to till the engine reaches to allowable minimum speed.
- Driving mode control
If the vehicle runs normally, fuel injection volume will be calculated by accelerator pedal travel and
engine rpm and the drive map will be used to match the drivers inputs with optimum engine power.
15-10

(2) Fuel Control

a. Fuel Pressure Control Elements
Pressure control consists of 2 principles.
- Determines rail pressure according to engine operating conditions.
- Controls IMV to make the rail pressure to reach to the required value.
Pressure in the fuel rail is determined according to engine speed and load on the engine.
- When engine speed and load are high
The degree of turbulence is very great and the fuel can be injected at very high pressure in order to
optimize combustion.
- When engine speed and load are low
The degree of turbulence is low. If injection pressure is too high, the nozzle's penetration will be
excessive and part of the fuel will be sprayed directly onto the sides of the cylinder, causing
incomplete combustion. So there occurs smoke and damages engine durability.
Fuel pressure is corrected according to air temperature, coolant temperature and atmospheric pressure
and to take account of the added ignition time caused by cold running or by high altitude driving. A
special pressure demand is necessary in order to obtain the additional flow required during starts. This
demand is determined according to injected fuel and coolant temperature.

b. Fuel Pressure Control

Rail pressure is controlled by closed loop regulation of IMV.
▶ Open loop determines the current which needs to be sent to the actuator in order to obtain the flow
demanded by the ECU.
▶ Closed loop will correct the current value depending on the difference between the pressure demand
and the pressure measured.
- If the pressure is lower than the demand, current is reduced so that the fuel sent to the high pressure
pump is increased.
- If the pressure is higher than the demand, current is increased so that the fuel sent to the high
pressure pump is reduced.
 0000-00 15-11

c. Fuel Injection Control

Injection control is used in order to determine the characteristics of the pulse which is sent to the
injectors.
Injection control consists as below.
- Injection timing
- Injection volume
- Translating fuel injection timing and injection volume into values which can be interpreted by the
injector driver.

▶ Main injection timing control

The pulse necessary for the main injection is determined as a function of the engine speed and of the
injected flow.
The elements are:
- A first correction is made according to the air and coolant temperatures.
This correction makes it possible to adapt the timing to the operating temperature of the engine.
When the engine is warm, the timing can be retarded to reduce the combustion temperature and
polluting emissions (NOx). When the engine is cold, the timing advance must be sufficient to allow
the combustion to begin correctly.
- A second correction is made according to the atmospheric pressure.
This correction is used to adapt the timing advance as a function of the atmospheric pressure and
therefore the altitude.
- A third correction is made according to the coolant temperature and the time which has passed since
starting.
This correction allows the injection timing advance to be increased while the engine is warming up
(initial 30 seconds). The purpose of this correction is to reduce the misfiring and instabilities which are
liable to occur after a cold start.
- A fourth correction is made according to the pressure error.
This correction is used to reduce the injection timing advance when the pressure in the rail is higher
than the pressure demand.
- A fifth correction is made according to the rate of EGR.
This correction is used to correct the injection timing advance as a function of the rate of exhaust gas
recirculation.
When the EGR rate increases, the injection timing advance must in fact be increased in order to
compensate for the fall in termperature in the cylinder.
During starting, the injection timing must be retarded in order to position the start of combustion close to
the TDC. To do this, special mapping is used to determine the injection timing advance as a function of
the engine speed and of the water temperature.
15-12

▶ Pilot injection timing control

The pilot injection timing is determined as a function of the engine speed and of the total flow.
The elements are:
- A first correction is made according to the air and coolant temperatures. This correction allows the
pilot injection timing to be adapted to the operating temperature of the engine.
- A second correction is made according to the atmospheric pressure. This correction is used to adapt
the pilot injection timing as a function of the atmospheric pressure and therefore the altitude.

d. Fuel Control
1. Main Flow Control
The main flow represents the amount of fuel injected into the cylinder during the main injection. The pilot
flow represents the amount of fuel injected during the pilot injection.

The total fuel injected during 1 cycle (main flow + pilot flow) is determined in the following manner.
▶ When the driver depress the pedal, it is his demand which is taken into account by the system in order
▶ to determine the fuel injected.
When the driver release the pedal, the idle speed controller takes over to determine the minimum fuel
which must be injected into the cylinder to prevent the enigne from stalling.
It is therefore the greater of these 2 values which is retained by the system. This value is then compared
with the lower flow limit determined by the ESP system.
As soon as the injected fuel becomes lower than the flow limit determined by the ESP system, the
antagonistic torque (engine brake) transmitted to the drive wheels exceeds the adherence capacity of
the vehicle and there is therefore a risk of the drive wheels locking.
The system thus chooses the greater of these 2 values (main flow & pilot flow) in order to prevent any
loss of control of the vehicle during a sharp deceleration.
As soon as the injected fuel becomes higher than the fuel limit determined by the ASR trajectory control
system, the engine torque transmitted to the wheels exceeds the adhesion capacity of the vehicle and
there is a risk of the drive wheels skidding. The system therefore chooses the smaller of the two values
in order to avoid any loss of control of the vehicle during accelerations.
The anti-oscillation strategy makes it possible to compensate for fluctuations in engine speed during
transient conditions. This strategy leads to a fuel correction which is added to the total fuel of each
cylinder.

A switch makes it possible to change over from the supercharge fuel to the total fuel according to the
state of the engine.
- Until the stating phase has finished, the system uses the supercharged fuel.
- Once the engine changes to normal operation, the system uses the total fuel.
The main fuel is obtained by subtracting the pilot injection fuel from the total fuel.
A mapping determines the minimum fuel which can control an injector as a function of the rail pressure.
As soon as the main fuel falls below this value, the fuel demand changes to 0 because in any case the
injector is not capable of injecting the quantity demand.
 0000-00 15-13

2. Driver Demand
The driver demand is the translation of the pedal position into the fuel demand. It is calculated as a
function of the pedal position and of the engine speed. The driver demand is filtered in order to limit the
hesitations caused by rapid changes of the pedal position. A mapping determines the maximum fuel
which can be injected as a function of the driver demand and the rail pressure. Since the flow is
proportional to the injection time and to the square root of the injection pressure, it is necessary to limit
the flow according to the pressure in order to avoid extending the injection for too long into the engine
cycle. The system compares the driver demand with this limit and chooses the smaller of the 2 values.
The driver demand is then corrected according to the coolant temperature. This correction is added to
the driver demand.
15-14

3. Idle Speed Controller

The idle speed controller consists of 2 principal modules:
- The first module determines the required idle speed according to:
* The operating conditions of the engine (coolant temperature, gear engaged)
* Any activation of the electrical consumers (power steering, air conditioning, others)
* The battery voltage
* The presence of any faults liable to interface with the rail pressure control or the injection control. In
this case, increase the idle speed to prevent the engine from stalling.
- The second module is responsible for providing closed loop control of the engine's idle speed by
adapting the minimum fuel according to the difference between the required idle speed and the
engine speed.

4. Flow Limitation
The flow limitation strategy is based on the following strategies:
- The flow limitation depending on the filling of the engine with air is determined according to the
engine speed and the air flow. This limitation allows smoke emissions to be reduced during
stabilized running.
- The flow limitation depending on the atmospheric pressure is determined according to the engine
speed and the atmospheric pressure. It allows smoke emissions to be reduced when driving at
altitude.
- The full load flow curve is determined according to the gear engaged and the engine speed. It
allows the maximum torque delivered by the engine to be limited.
- A performance limitation is introduced if faults liable to upset the rail pressure control or the
injection control are detected by the system. In this case, and depending on the gravity of the fault,
the system activates:
Reduced fuel logic 1: Guarantees 75 % of the performance without limiting the engine speed.
Reduced fuel logic 2: Guarantees 50 % of the performance with the engine speed limited to 3,000 rpm.
Reduce fuel logic 3: Limits the engine speed to 2,000 rpm.

The system chooses the lowest of all values.

A correction depending on the coolant temperature is added to the flow limitation. This correction makes
it possible to reduce the mechanical stresses while the engine is warming up. The correction is
determined according to the coolant temperature, the engine speed and the time which has passed
since starting.

Superchager Flow Demand

The supercharge flow is calculated according to the engine speed and the coolant temperature. A
correction depending on the air temperature and the atmospheric pressure is made in order to increase
the supercharge flow during cold starts. It is possible to alter the supercharge flow value by adding a flow
offset with the aid of the diagnostic tool.
 0000-00 15-15

5. Pilot Flow Control

The pilot flow represents the amount of fuel injected into the cylinder during the pilot injection. This
amount is determined according to the engine speed and the total flow.
- A first correction is made according to the air and water temperature.
This correction allows the pilot flow to be adapted to the operating temperature of the engine. When
the engine is warm, the ignition time decreases because the end-of-compression temperature is
higher. The pilot flow can therefore be reduced because there is obviously less combustion noise
when the engine is warm.
- A second correction is made according to the atmospheric pressure.
During starting, the pilot flow is determined on the basis of the engine speed and the coolant
temperature.

6. Cylinder Balancing Strategy

▶ Balancing of the point to point flows
The pulse of each injector is corrected according to the difference in instantaneous speed measured
between 2 successive injectors.
The instantaneous speeds on two successive injections are first calculated.
The difference between these two instantaneous speeds is then calculated.
Finally, the time to be added to the main injection pulse for the different injectors is determined. For each
injector, this time is calculated according to the initial offset of the injector and the instantaneous speed
difference.

▶ Detection of an injector which has stuck closed

The cylinder balancing strategy also allows the detection of an injector which has stuck closed. The
difference in instantaneous speed between 2 successive injections then exceeds a predefined threshold.
In this case, a fault is signaled by the system.
15-16

e. MDP Learning Control

MDP (Minimum Drive Pulse ) refers to the

minimum power supply pulse for injection which
the injector can perform. It is possible to control
the fuel volume for each injector accurately
through correct learning for the MDP value. The
basic process of MDP learning is that the pulse
slightly higher than MDP is supplied and then (b)
the vibration generated from the cylinder is
detected. The knock sensor detects the vibration
from the engine after a small volume of fuel is
injected. And the time interval between the points
of injection and vibration is measured so that
MDP can be learned. MDP learning is helpful to
prevent engine vibration, high emission and
power reduction through performing calibration
for the old injectors. During MDP learning, a little
vibration and noise can be occur for a while. This
is because the fuel pressure is increased
instantaneously and the exact injection value is
not input, so that the exact engine vibration
timing can be detected.
 0000-00 15-17

(3) Accelerometer Control

a. Resetting the pilot injection
The accelerometer is used to reset the pilot injection flow in closed loop for each injector. This method
allows the correction of any injector deviations over a period of time. The principle of use of the
accelerometer is based on the detection of the combustion noises.
The sensor is positioned in such a way as to receive the maximum signal for all the cylinders. The raw
signals from the accelerometer are processed to obtain a variable which quantifies the intensity of the
combustion. This variable, known as the ratio, consists of the ratio between the intensity of the
background noise and the combustion noise.
1. A first window is used to establish the background noise level of the accelerometer signal for each
cylinder. This window must therefore be positioned at a moment when there cannot be any
combustion.
2. The second window is used to measure the intensity of the pilot combustion. Its position is such that
only the combustion noises produced by the pilot injection are measured . It is therefore placed just
before the main injection.
The accelerometer does not allow any evaluation of the quantity injected. However, the pulse value will
be measured when the injector starts injection and this pulse value is called the MDP (Minimum Drive
Pulse). On the basis of this information, it is possible to efficiently correct the pilot flows. The pilot
injection resetting principle therefore consists of determining the MDP, in other words the pulse
corresponding to the start of the increase in value of the ratio (increase of vibration due to fuel
combustion).
15-18

This is done periodically under certain operating conditions. When the resetting is finished, the new
minimum pulse value replaces the value obtained during the previous resetting. The first MDP value is
provided by the C3I. Each resetting then allows the closed loop of the MDP to be updated according to
the deviation of the injector.

b. Detection of leaks in the cylinders

The accelerometer is also used to detect any injector which may have stuck open. The detection
principle is based on monitoring the ratio. If there is a leak in the cylinder, the accumulated fuel self-
ignites as soon as the temperature and pressure conditions are favorable (high engine speed, high load
and small leak).
This combustion is set off at about 20 degrees before TDC and before main injection.
The ratio therefore increases considerably in the detection window. It is this increase which allows the
leaks to be detected. The threshold beyond which a fault is signaled is a percentage of the maximum
possible value of the ratio.
Because of the severity of the recovery process (engine shut-down), the etection must be extremely
robust.
An increase in the ratio can be the consequence of various causes:
- Pilot injection too much
- Main combustion offset
- Fuel leak in the cylinder
If the ratio becomes too high, the strategy initially restricts the pilot injection flow and retards the main
injection. If the ratio remains high despite these interventions, this shows that a real leak is present, a
fault is signaled and the engine is shut down.

c. Detection of an accelerometer fault

This strategy permits the detection of a fault in the sensor or in the wiring loom connecting the sensor to
the ECU.
It is based on detection of the combustion. When the engine is idling, the detection window is set too low
for the combustion caused by the main injection. If the ratio increases, this shows that the accelerometer
is working properly, but otherwise a fault is signaled to indicate a sensor failure. The recovery modes
associated with this fault consist of inhibition of the pilot injection and discharge through the injectors.
 0000-00 15-19

(4) Swirl control

a. Overview
- Variable swirl valve
The strong swirl caused by intake air is important element for anti-locking function in diesel engine. The
swirl control valve partially closes the intake port to generate the swirl according to the engine conditions.
When the engine load is in low or medium range, the swirl could not be generated because the air flow
is slow. To generate strong swirl, there are two passages in intake manifold, and one of them has the
valve to open and close the passage. When the valve closes the passage, the air flow through the
another passage will be faster, and the strong swirl will be generated by the internal structure of the
passage. This swirl makes the better mixture of air and fuel, eventually the combustion efficiency in
combustion chamber could be improved. This provides the enhanced fuel consumption, power and
EGR ratio.

- Components

Coolant Accelerator pedal

temperature

D20DTF ECU

Crankshaft
Variable swirl position sensor HFM
valve
15-20

b. Input/Output for variable swirl valve

 0000-00 15-21

c. Types of swirl

Swirl: One cylinder has two intake air ports, one is set horizontally
and the other one is set vertically. Swirl is the horizontal air flows in
cylinder due to the horizontal intake air ports.

Tumble: Tumble is the vertical air flows in cylinder due to the vertical
intake air port

Squish: Squish is the air flows due to the piston head. Normally, this
is appears at the final process of compression. In CRDi engine, the
piston head creates the bowl type squish.

d. Swirl control
In DI type diesel engine, the liquefied fuel is injected into the cylinder directly. If the fuel is evenly
distributed in short period, the combustion efficiency could be improved. To get this, there should be
good air flow in cylinder. In general, there are two intake ports, swirl port and tangential port, in each
cylinder. The swirl port generates the horizontal flow and the tangential port generates the longitudinal
flow.
In low/mid load range, the tabgential port is closed to increase the horizontal flow. Fast flow decreases
the PM during combustion and increases the EGR ratio by better combustion efficiency.
15-22

Load Engine speed Swirl Amount of Remarks

valve swirl
Low speed, below 3,000 rpm Closed Heavy Increased EGR ratio, better air-fuel
Low load mixture (reduce exhaust gas)
High speed, over 3,000 rpm Open Light Increase charge efficiency, higher
High load engine power

The variable swirl valve actuator operates when

turning the ignition switch ON/OFF position to
open/close the swirl valve. In this period, the soot
will be removed and the learning for swirl valve
position is performed.

Swirl valve

Swirl: This is the twisted (radial) air flow along the cylinder wall during the intake stroke. This stabilizes
the combustion even in lean air-fuel mixture condition.

e. Features
- Swirl and air intake efficiency
To generate the swirl, the intake port should be serpentine design. This makes the resistance in air
flow. The resistance in air flow in engine high speed decreases the intake efficiency. Eventually, the
engine power is also decreased, Thus, the swirl operation is deactivated in high speed range to
increase the intake efficiency.
- Relationship between swirl and fuel injection pressure
The injector for DI engine uses the multi hole design. For this vehicle, there are 8 holes in injector. If
the swirl is too strong, the injection angles might be overlapped and may cause the increased PM and
insufficient engine power. Also, if the injection pressure is too high during strong swirl, the injection
angles might be overlapped. Therefore, the system may decreases the fuel injection pressure when
the swirl is too strong.
 0000-00 15-23

f. Relationship between swirl and fuel injection pressure

- The injector for DI engine uses the multi hole design. For this vehicle, there are 8 holes in injector. If
the swirl is too strong, the injection angles might be overlapped and may cause the increased PM and
insufficient engine power. Also, if the injection pressure is too high during strong swirl, the injection
angles might be overlapped. Therefore, the system may decreases the fuel injection pressure when
the swirl is too strong.

* Anti-knock methods:
- Shorten the ignition timing by pilot injection, lessen the fuel injection volume during ignition delay
period.
- Increase engine speed.
- Maintain intake sir temperature with intercooler or glow plug device.
- Increase intake air pressure with turbocharger.
- Warm up engine to keep the normal operating temperature.
- Increase compression ratio.
- Use the fuel with high cetane.
15-24

(5) EGR control

a. Overview
The EGR (Electric-Exhaust Gas Recirculation) valve reduces the NOx emission level by recirculating
some of the exhaust gas to the intake system.
The major difference with the previous EURO 4 type, is that the DC motor with improved response rate
according to the EURO 5 regulation. The solenoid type actuator is used in the conventional model, but in
this new model, the DC motor type actuator with improved response rate is adopted. Also the hall sensor
which provides a more stabilized signal than the potentiometer, and the EGR bypass flap which
improves engine warming up efficiency are also used. The HFM sensor and the position sensor are
used to feedback the amount of EGR for both EURO 4 and EURO 5.

b. Components

Oxygen sensor Accelerator D20DTF ECU

pedal

Coolant Crankshaft posi.

temp.sensor sensor

Electronic T-MAP sensor HFM sensor

E-EGR cooler throttle body E-EGR valve (intake air temp.)
 0000-00 15-25

c. Input/Output of E-EGR system

15-26

d. Bypass control for EGR cooler

1. Cooler temperature

When the coolant temperature is below 70℃, the exhaust gas is bypassed the EGR cooler.

2. Exhaust gas temperature

When the exhaust gas temperature is below 300℃, the exhaust gas is bypassed the EGR cooler.
Otherwise, PM could be increased due to too low exhaust gas temperature.

e. Control elements for EGR system

- Accelerator pedal (engine load) - Indicates the driver's intention and engine load. If the load goes up,
the EGR ratio is decreased.
- T-MAP (boost pressure map stored in ECU) - Compensates the difference in boost pressure by
adjusting EGR ratio.
- Engine rpm - Used as the signal for determining EGR operating range.
- Coolant temperature - When the coolant temperature is low, NOx is decreased but PM could be
increased. So, to reduce PM, decrease EGR ratio when the coolant temperature is low.
- Intake air mass and temperature - HFM sensor measures the intake air mass to calculate the actual
EGR volume. If the air mass is larger than programmed value in map, EGR ratio will be higher.
EGR position sensor - Detects the actual opening angle of EGR valve and performs feedback
- function according to PWM control by ECU.
Wide band oxygen sensor - Detects the oxygen volume in exhaust gas to check if the EGR ratio is
- proper.
Electronic throttle body - Keeps EGR ratio to optimized level by controlling the throttle body in EGR
- operating range (decreasing pressure in intake manifold).
 0000-00 15-27

f. Features

As EGR ratio goes up, smoke volume will be As EGR temperature goes up, the
higher. But, this lowers the combustion chamber concentration of NOx will be higher. Thus, it is
temperature and accordingly the concentration of necessary to cool down the exhaust gas.
NOx is decreased. The point with highest NOx is However, during engine cooled, it may cause
immediately after TDC. large amount of PM. To prevent this, the
exhaust gas is bypassed the EGR cooler.
15-28

(6) E-VGT control

a. Overview
E-VGT (Electric-Variable Geometry Turbine) turbocharger system in D20DTF engine uses the venturi
effect that controls the flow rate of exhaust gas by adjusting the passage in turbine housing. The newly
adopted DC motor actuator (E-actuator) controls the E-VGT system more precisely and faster. To get
the high operating power from turbine, the ECU reduces the exhaust gas passage In low speed range
and increases it in high speed range.

b. Components

E-VGT Accelerator
actuator pedal

ECU
Coolant (D20DTF)
temperature

HFM sensor
Front EGT T-MAP sensor Crankshaft pos, (intake air temp)
sensor sensor
 0000-00 15-29

c. Input/Output for E-VGT system

15-30

d. E-VGT system control

Turbocharger system operates the E-VGT actuator according to the signals for engine epm, accelerator
pedal position, atmospheric pressure, T-MAP, coolant temperature and intake air temperature.
Turbocharger actuator is performed PWM control by ECU.
In general, the boost pressure feedbacks the turbocharger operation and the boost temperature is used
for calculating the precise density.
E-VGT provides higher engine power with faster reaction speed compared to conventional VGT.

Operating wave Vane Control

In low speed range:
retract the vane to
increase boost
pressure. The vane
Low has low (-) duty, and
speed the unison ring
range moves to retract the
vane in weak PWM
signal.

The unison ring

moves to extend the
vane in strong PWM
signal. Maximum
High pressure is 3 bar
speed and the system
range controls it according
to the input signals.
 0000-00 15-31

(7) Wide band oxygen sensor

a. Overview
For diesel engine, combustion is not performed at the optimum (theoretically correct) air-fuel ratio and
the oxygen concentration is thin in most cases. So the wide-band oxygen sensor is used for this kind of
engine, and this sensor is a little different from the one that used for gasoline engine. The combustion in
diesel engine is controlled by fuel injection volume. Therefore, the wide band oxygen sensor should be
used in diesel engine. This sensor measures the air-fuel ratio in very wide range, and is also called full
range oxygen sensor.
- The wide band oxygen sensor measures the oxygen density in exhaust gas and sends it to ECU to
control the EGR more precisely.

b. Components

D20DTF Oxygen Injector (C3I) HFM sensor

ECU sensor (air mass)

EGR valve Electronic Coolant temp. CDPF

throttle body sensor
15-32

c. Input/Output for oxygen sensor

 0000-00 15-33

d. Oxygen sensor control

The wide band oxygen sensor uses ZnO2. It produces the voltage by movement of oxygen ions when
there is oxygen concentration difference between exhaust gas and atmosphere.
If a certain voltage is applied to the sensor, the movement of oxygen ions occurs regardless of the
oxygen density. The current generated through this flow of ions, is called pumping current (IP), and the
oxygen sensor measures this value.
15-34

(8) Cooling fan control

a. Overview of cooling fan and A/C compressor
The cooling system maintains the engine temperature at an efficient level during all engine operating
conditions. The water pump draws the coolant from the radiator. The coolant then circulates through
water jackets in the engine block, the intake manifold, and the cylinder head. When the coolant reaches
the operating temperature of the thermostat, the thermostat opens. The coolant then goes back to the
radiator where it cools. The heat from automatic transaxle is also cooled down through the radiator by
circulating the oil through the oil pump.
There are two cooling fans (200W+150W) in D20DTF engine. ECU controls the electric cooling fans
with three cooling fan relays to improve the engine torque and air conditioning performance.

For details about A/C compressor and refrigerant pressure sensor, refer to Chapter "Air Conditioning
System" in "Body" section.

b. Components

Coolant temp. DSI 6 A/T ECU

sensor (ATF temp.) D20DTF

Refrigerant pres. Engine room

sensor relay box

HFM sensor
A/C compressor (Intake air
Cooling fan module
temperature)
 0000-00 15-35

c. Input/Output for cooling fan and A/C compressor

15-36

d. Cooling fan and A/C compressor control

▶ Conditions for cooling fan
The cooling fan module controls the cooling fan relay, high speed relay and low speed relay. The cooling
fan is controlled by the series and parallel circuits.

A/C switch Cooling fan Coolant temperature Refrigerant pressure A/C

compressor
OFF Coolant temp. < 90℃ -

OFF LO 90℃ ≤ Coolant temp. -

< 105℃
HI 105℃ ≤ Coolant temp -
Refrigerant pressure <
LO
18 bar
Coolant temp. < 105℃
18 bar ≤ Refrigerant
HI ON
ON pressure

HI 105℃ ≤ Coolant temp. -

< 115℃
HI 115℃ ≤ Coolant temp. - OFF (cut)

▶ A/C compressor OFF conditions

- Coolant temperature: below -20℃ or over
115℃
- Approx. 4 seconds after starting the engine
- Engine rpm: below 650 rpm or over 4500 rpm
- When abrupt acceleration
- Refrigerant pressure:
* OFF below 2.0 kg/㎠, then ON over 2.4 kg/㎠
* OFF over 30 kg/㎠, then ON below 21.4 kg/㎠

▶ Output voltage according to refrigerant pressure

The output voltage from refrigerant pressure sensor is 1.7 V to 3.5 V when the refrigerant pressure is 10
to 24 kgf/㎠ with A/C "ON".

▶ Cooling fan control according to ATF temperature

ATF temperature Cooling fan Remark

Over 100˚C High speed -
 0000-00 15-37

(9) PTC heater control

a. Overview
The supplementary electrical heater is installed in DI engine equipped vehicle as a basic equipment. The
PTC system is operated according to two temperature values measured at the coolant temperature
sensor and HFM sensor. This device is mounted in the heater air outlet and increase the temperature of
air to the passenger compartment. Because PTC system is heated by electrical power, high capacity
alternator is required. PTC does not operate during engine cranking, while the battery voltage is lower
than 11 V or during preheating process of glow plugs.

b. Components

D20DTF
ECU

PTC heater

Engine room relay box

Coolant HFM
temp. sensor (Intake air
temp.)

A: PTC 1 (changeable)
B: PTC 2,3 (not changeable)
15-38

c. Operation process
The ceramic PTC has a feature that the resistance goes up very high at a certain temperature. There
are three circuits in PTC heater. Only one circuit is connected when PTC1 relay is ON, and two circuits
are connected when PTC2 relay is ON.
Operation process: reaches at a certain temperature→high resistance→low current→less heat
radiation→temperature down→high resistance→high current→temperature up
 0000-00 15-39

d. Control conditions

Operation Operating condition PTC Heater

HI - Coolant temperature < 15℃ PTC HI ON
(PTC2)
- Coolant temperature 15℃ ≤ 65℃, intake air
temperature ≤ -10℃
LO - Coolant temperature 15℃ < 65 to 60℃, intake air PTC LO ON
(PTC1) temperature <-10℃ to 0℃
- Coolant temperature 15℃ ≤ 60℃, intake air
temperature ≤ 0℃ to 5℃
- A/C blower switch OFF
- Defective ambient air temperature sensor
Stop (including open or short circuit)
- Engine cranking
- Low battery voltage (below 11V)
- During pre-glow process (glow indicator ON)

▶ Operation diagram for PTC heater LO (step 2)

15-40

(10) Immobilizer control

a. Overview
The Immobilizer System provides an additional theft deterrent to the vehicle in which it is installed and
prevents it from being started by unauthorized persons. The transponder integrated in the key and the
engine control unit have the same code. When the ignition key with the integrated transponder is turned
to the ON position, the ECU (Engine Control Unit) checks the crypto code of the key and, if correct,
allows the vehicle to start the engine.

For details, refer to Chapter "BCM".

b. Components

▶ Basic components (ignition key system)

Immobilizer Meter
antenna cluster

Immobilizer key BCM

ECU
D20DTF
Start motor
 0000-00 15-41

▶ Key approval process

When turning the ignition switch to ON position, the power is supplied to BCM and ECU. ECU
communicate with the immobilizer key to check if it is valid crypto code. If it is valid, ECU start to control
the engine when turning the ignition switch to START position.
The system has 10 seconds of valid time-out period. If the engine does not start in this period, the key
approval process should be done again.
15-42

c. Components for immobilizer with Smart key system

▶ Components (For antenna, refer to Chapter “SKM”)

Smart key Meter

slot cluster

Smart key BCM

Start motor D20DTF SKM

ECU
 0000-00 15-43

▶ Key approval process in Smart key system equipped vehicle

The key approval consists of two processes; immobilizer key approval and Smart key
approval.
Immobilizer key approval: When inserting the Smart key into Smart key slot, the power is supplied to the
key slot. SKM communicate with the Smart key in key slot to check if it has valid crypto code. If it is valid,
ECU start to control the engine when pressing the Engine Start/Stop button. The system has 10
seconds of valid time-out period. If the engine does not start in this period, the key approval process
should be done again.
Smart key approval: When pressing the Engine Start/Stop button or depressing the brake pedal without
Smart key inserted into the key slot, SKM communicate with the Smart key to check if it has valid crypto
code. If it is valid, the engine can be started.
15-44

(11) CDPF control

a. Overview
As the solution for environmental regulations and PM Particle Material) of diesel engine, the low emission
vehicle is getting popular. This vehicle is equipped with an extra filter to collect the soot and burn it again
so that the amount of PM in the exhaust gas passed through the DOC (Diesel Oxidation Catalyst) is
reduced. The CDPF (Catalyst & Diesel Particulate Filter) is an integrated filter including DOC (Diesel
Oxidation Catalyst) and DPF (Diesel Particulate Filter).

For details, refer to Chapter "CDPF".

b. Components

Oxygen sensor CDPF (DOC+DPF) Front temp.

sensor

Rear temp. Throttle valve D20DTF ECU Differential pres.

sensor sensor
 0000-00 15-45

c. Input/Output for CDPF control

15-46

d. Operation process
When the differential pressure sensor detects the pressure difference between the front and the rear
side of CDPF, the sensor sends signal indicating the soot is accumulated and the post injection is
performed to raise the temperature of exhaust gas. The amount of fuel injected is determined according
to the temperature of exhaust gas detected by the rear temperature sensor. If the temperature is below
600°C, the amount of fuel injected is increased to raise the temperature. If the temperature is over
600°C, the amount of fuel injected is decreased or not controlled. When the engine is running in
low load range, the amount of post injection and the amount of intake air are controlled. It is to raise the
temperature by increasing the amount of fuel while decreasing the amount of intake air.

Front temp. DOC performs

sensor: Measure oxidation and
DOC temp. reduction process at Injector: Control
300~500˚C, and post injection
front temperature
sensor monitors the Intake air
temperature of mass
DOC.

Rear temp. sensor: DPF performs ECU (DCM 3.7)

Measure DPF recycling
temp. (combustion) Post injection
process at 600C,
and rear Control intake air
temperature sensor mass
monitors the
temperature of DPF.
Electronic
Diff. pres. sensor: Differential pressure throttle body:
Measure sensor measures the Control intake air
pressure between pressure difference mass
Booster
front side and between pre-CDPF Exceed PM
rear side of CDPF and post-CDPF (If pressure/
limit temperature
PM has been
accumulated, the
measured value is T-MAP sensor
over the specified
value).
 0000-00 15-47

e. Cautions
- Use only specified Engine Oil (approved by MB Sheet 229.51) for CDPF.

1. Use only specified engine oil (Low Ash Oil)

- The vehicle equipped with CDPF should use specific engine oil to improve the engine performance
and fuel economy, and ensure the service life of CDPF.

2. Issue with normal engine oil

- Sulfur, one of the contents of engine oil is burned and generates soot that is not regenerated by the
DPF. This remains on the filter as ashes and keeps accumulating. Eventually, this ashes will block the
filter.

3. Benefit for specified engine oil

- Minimized the sulfur content of engine oil which reduces the service life.
- Improved fuel economy and emission level of CO2 with high performance and low viscosity.
- Increased service life of engine oil with high resistance to temperature.

4. Problems when using unspecified engine oil

- The service life of filter may be reduced by 30% or more by the ashes accumulated on the filter.
The fuel economy may be reduced because of engine rolling resistance, frequent regeneration of
- DPF.

* These problems are also caused by oil with high sulfur content, such as tax exemption oil and
heating oil, etc.
15-48

3) Input/Output for CAN communication

(1) Configuration of CAN (P-CAN/B-CAN)

Abbreviation Function
GCU Glow Control Unit
EPS Electronic Power Steering Unit
BCM Body Control Module
SKM Smart Key Module
TPMS Tire Pressure Monitering System

CAN Topology communicate with system units. There are two types (P-CAN and B-CAN) of
communication according to the communication speed. Instrument cluster, BCM and diagnostic
connector use both types of communication. And, ECU, ABS & ESP, TCU, GCU, E-coupling and EPS
unit use P-CAN communication because it is faster than B-CAN. The terminal resistances are installed in
ECU and BCM.
 0000-00 15-49

(2) CAN communication flow chart

Splice pack Wiring harness Location

S101 W/H Floor(LH) Glow Control Unit
S102 W/H Floor(RH) Inside RH Fender
S202 Main wiring Backside Cluster(LH Cowl Cross Member)
S204 Main wiring Backside Cluster(Upper ICM Relay Box)
S205 W/H Main Backside Audio(CTR Cowl Cross Member)
S206 W/H Floor(LH) Under Driver Seat
S401 W/H Floor(LH) Beside PAS Unit(Inside LH QTR Trim)
15-50

(3) Input/Output for CAN communication