PT 70 80 Service Manual 1 08

Service Manual
PT-70/PT-80
Rubber Track Loader
• Safety Overview
• Technical Specifications
• Circuit Diagrams
• Maintenance
• Controls & Instrumentation
• Component Removal & Installation
• Hydraulic Component Service
• Hydraulic Pressure & Flow Check & Adjustment
• Troubleshooting
ASVPT003
Part Number: 2046-159
Printed (1-08)
PT-70/PT-80
Service Manual
Printed (1-08)
Table of Contents
1. Product Safety 3. Circuit Diagrams

Chapter Overview . . . . . . . . . . . . . . . . . . . . . 1-1 Chapter Overview . . . . . . . . . . . . . . . . . . . . . 3-1
Safety Messages . . . . . . . . . . . . . . . . . . . . . 1-1 Hydraulic Charge Circuit . . . . . . . . . . . . . . . . 3-1
Information Messages . . . . . . . . . . . . . . . . . 1-1 Hydraulic Auxiliary Circuit . . . . . . . . . . . . . . . 3-2
Basic Precautions . . . . . . . . . . . . . . . . . . . . . 1-1 Hydraulic Drive Circuit . . . . . . . . . . . . . . . . . 3-3
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . 1-1 Lift Arm Control Valve . . . . . . . . . . . . . . . . . . 3-4
Protective Equipment . . . . . . . . . . . . . . . . 1-2 Hydraulic Pilot Generation Solenoid Block . . 3-5
Entering and Exiting . . . . . . . . . . . . . . . . . 1-2 Electrical Attachment Outlet . . . . . . . . . . . . . 3-6
Lifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Drive Control (line routing) . . . . . . . . . . . . . . 3-7
Hot Fluids and Components . . . . . . . . . . . 1-2 Lift Arm Control (line routing) . . . . . . . . . . . . 3-8
Corrosion Inhibitor . . . . . . . . . . . . . . . . . . . 1-2
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 4. Maintenance
Pressurized Items . . . . . . . . . . . . . . . . . . . 1-2 Chapter Overview . . . . . . . . . . . . . . . . . . . . . 4-1
Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Personal Safety . . . . . . . . . . . . . . . . . . . . . . 4-1
Work Tools . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Lift-Arm Brace . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Asbestos Information . . . . . . . . . . . . . . . . . . 1-4 Tilt-up Cab . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Machine Labels and Decals . . . . . . . . . . . . . 1-4 Jacking Procedure . . . . . . . . . . . . . . . . . . . . 4-2
Product Identification Number . . . . . . . . . . 1-4 Grease Fittings . . . . . . . . . . . . . . . . . . . . . . . 4-3
Engine Serial Number . . . . . . . . . . . . . . . . 1-4 Undercarriages . . . . . . . . . . . . . . . . . . . . . . . 4-3
Machine Label and Decal Examples . . . . . 1-5 Track Tension . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Drive Sprocket Rollers . . . . . . . . . . . . . . . . . 4-5
2. Technical Specifications Track Removal . . . . . . . . . . . . . . . . . . . . . . . 4-6
Specifications (PT-80) . . . . . . . . . . . . . . . . . . 2-1 Track Installation . . . . . . . . . . . . . . . . . . . . . . 4-8
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Transmission . . . . . . . . . . . . . . . . . . . . . . . 2-1 Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
Drive Pumps . . . . . . . . . . . . . . . . . . . . . . 2-1 Water Separator . . . . . . . . . . . . . . . . . . . . . . 4-11
Charge Pump . . . . . . . . . . . . . . . . . . . . . 2-1 Accessory Belt Tension . . . . . . . . . . . . . . . . 4-12
Drive Motors . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Fan Belt Removal/Installation . . . . . . . . . . . . 4-13
Pilot Controls . . . . . . . . . . . . . . . . . . . . . . . . 2-1 A/C Belt Removal/Installation . . . . . . . . . . . . 4-13
Auxiliary Pump . . . . . . . . . . . . . . . . . . . . . . . 2-1 Engine Oil/FIlter Change . . . . . . . . . . . . . . . 4-14
Lift Arm Control Valve . . . . . . . . . . . . . . . . . . 2-1 Engine Oil Specifications . . . . . . . . . . . . . . . 4-15
Oil Cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Oil Level Check . . . . . . . . . . . . . . . . . . . . . . 4-15
Critical Torque Specifications . . . . . . . . . . . . 2-1 Hydraulic Fluid/Filter Change . . . . . . . . . . . . 4-16
Cycle Times . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Radiator/Oil Cooler (cleaning) . . . . . . . . . . . 4-17
Service Tools . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Engine (cleaning) . . . . . . . . . . . . . . . . . . . . . 4-17
Specifications (PT-70) . . . . . . . . . . . . . . . . . . 2-2 Case Drain Filter . . . . . . . . . . . . . . . . . . . . . . 4-18
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Fuse Panel . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18
Transmission . . . . . . . . . . . . . . . . . . . . . . . 2-2 Maintenance Schedule . . . . . . . . . . . . . . . . . 4-19
Drive Pumps . . . . . . . . . . . . . . . . . . . . . . 2-2
Charge Pump . . . . . . . . . . . . . . . . . . . . . 2-2 5. Machine Controls and Instrumentation
Drive Motors . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Chapter Overview . . . . . . . . . . . . . . . . . . . . . 5-1
Pilot Controls . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Machine Controls . . . . . . . . . . . . . . . . . . . . . 5-1
Auxiliary Pump . . . . . . . . . . . . . . . . . . . . . . . 2-2 Loader Control . . . . . . . . . . . . . . . . . . . . . . . 5-1
Lift Arm Control Valve . . . . . . . . . . . . . . . . . . 2-2 Drive Control . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Oil Cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Throttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Critical Torque Specifications . . . . . . . . . . . . 2-2 Instrumentation . . . . . . . . . . . . . . . . . . . . . . . 5-1
Cycle times . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Service Tools . . . . . . . . . . . . . . . . . . . . . . . . 2-2
I
Rubber Track Loader
Table of Contents
6. Operator Enclosure Machine Preparation . . . . . . . . . . . . . . . . . . . 8-1

Chapter Overview . . . . . . . . . . . . . . . . . . . . . 6-1 Removal & Installation . . . . . . . . . . . . . . . . . 8-1
Personal Safety . . . . . . . . . . . . . . . . . . . . . . 6-1 Fan Guard . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Machine Preparation . . . . . . . . . . . . . . . . . . . 6-1 Removal Procedure . . . . . . . . . . . . . . . . 8-1
Removal & Installation . . . . . . . . . . . . . . . . . 6-1 Installation Procedure . . . . . . . . . . . . . . 8-2
Door Gas Spring . . . . . . . . . . . . . . . . . . . . 6-1 Fan & Shroud . . . . . . . . . . . . . . . . . . . . . . 8-2
Removal Procedure . . . . . . . . . . . . . . . . 6-1 Removal Procedure . . . . . . . . . . . . . . . . 8-2
Installation Procedure . . . . . . . . . . . . . . 6-1 Installation Procedure . . . . . . . . . . . . . . 8-3
Pillar Switch Panels . . . . . . . . . . . . . . . . . . 6-2 Radiator/Oil Cooler . . . . . . . . . . . . . . . . . . 8-3
Removal Procedure . . . . . . . . . . . . . . . . 6-2 Removal . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
Installation Procedure . . . . . . . . . . . . . . 6-2 Installation . . . . . . . . . . . . . . . . . . . . . . . 8-4
Gauge Clusters (MP-2) . . . . . . . . . . . . . . . 6-3
Removal Procedure . . . . . . . . . . . . . . . . 6-3 9. Hydraulic Reservoir
Installation Procedure . . . . . . . . . . . . . . 6-3 Chapter Overview . . . . . . . . . . . . . . . . . . . . . 9-1
Side Panels/Gauges (MP-1) . . . . . . . . . . . 6-4 Personal Safety . . . . . . . . . . . . . . . . . . . . . . 9-1
Removal Procedure . . . . . . . . . . . . . . . . 6-4 Machine Preparation . . . . . . . . . . . . . . . . . . . 9-1
Installation Procedure . . . . . . . . . . . . . . 6-4 Removal & Installation . . . . . . . . . . . . . . . . . 9-1
Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5 Hydraulic Reservoir . . . . . . . . . . . . . . . . . . 9-1
Interior Side Panel, LT (MP-2) . . . . . . . . . . 6-5 Suction Screen . . . . . . . . . . . . . . . . . . . . . 9-8
Interior Side Panel, RT (MP-2) . . . . . . . . . 6-6
Removal Procedure . . . . . . . . . . . . . . . . 6-6 10. Lift Arm/Drive Controls
Installation Procedure . . . . . . . . . . . . . . 6-6 Chapter Overview . . . . . . . . . . . . . . . . . . . . .10-1
Interior Panel, Rear . . . . . . . . . . . . . . . . . . 6-7 Personal Safety . . . . . . . . . . . . . . . . . . . . . .10-1
Removal Procedure . . . . . . . . . . . . . . . . 6-7 Machine Preparation . . . . . . . . . . . . . . . . . . .10-1
Installation Procedure . . . . . . . . . . . . . . 6-7 Removal & Installation . . . . . . . . . . . . . . . . .10-1
Lap Bar Assist Gas Spring . . . . . . . . . . . . 6-7 Joystick . . . . . . . . . . . . . . . . . . . . . . . . . . .10-1
Removal Procedure . . . . . . . . . . . . . . . . 6-7 Removal Procedure . . . . . . . . . . . . . . . .10-1
Installation Procedure . . . . . . . . . . . . . . 6-7 Installation Procedure . . . . . . . . . . . . . .10-3
Lift Arm Float Magnet . . . . . . . . . . . . . . . .10-3
7. Chassis and Fuel Tank Removal . . . . . . . . . . . . . . . . . . . . . . . . .10-3
Chapter Overview . . . . . . . . . . . . . . . . . . . . . 7-1 Installation . . . . . . . . . . . . . . . . . . . . . . .10-3
Personal Safety . . . . . . . . . . . . . . . . . . . . . . 7-1 Lift Arm Control Valve . . . . . . . . . . . . . . . .10-4
Machine Preparation . . . . . . . . . . . . . . . . . . . 7-1 Removal . . . . . . . . . . . . . . . . . . . . . . . . .10-4
Removal & Installation . . . . . . . . . . . . . . . . . 7-1 Installation . . . . . . . . . . . . . . . . . . . . . . .10-4
Fuel Sending Unit . . . . . . . . . . . . . . . . . . . 7-1
Removal Procedure . . . . . . . . . . . . . . . . 7-1 11. Hydraulic Pumps/Motors
Installation Procedure . . . . . . . . . . . . . . 7-2 Chapter Overview . . . . . . . . . . . . . . . . . . . . . 11-1
Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Personal Safety . . . . . . . . . . . . . . . . . . . . . . 11-1
Removal Procedure . . . . . . . . . . . . . . . . 7-2 Machine Preparation . . . . . . . . . . . . . . . . . . . 11-1
Installation Procedure . . . . . . . . . . . . . . 7-3 Removal & Installation . . . . . . . . . . . . . . . . . 11-1
Footwell . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 Charge Pump . . . . . . . . . . . . . . . . . . . . . . . . 11-1
Removal Procedure . . . . . . . . . . . . . . . . 7-4 Removal Procedure . . . . . . . . . . . . . . . . . . 11-1
Installation Procedure . . . . . . . . . . . . . . 7-4 Installation Procedure . . . . . . . . . . . . . . . . 11-2
Foot Throttle Assembly . . . . . . . . . . . . . . . 7-5 Auxiliary Pump . . . . . . . . . . . . . . . . . . . . . . . 11-3
Hood Assembly . . . . . . . . . . . . . . . . . . . . . 7-5 Tandem Drive Pump . . . . . . . . . . . . . . . . . . . 11-4
Drive Motor . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6
8. Radiator and Oil Cooler Removal Procedure . . . . . . . . . . . . . . . . . . 11-6
Chapter Overview . . . . . . . . . . . . . . . . . . . . . 8-1 Installation Procedure . . . . . . . . . . . . . . . . 11-8
Personal Safety . . . . . . . . . . . . . . . . . . . . . . 8-1
II
Rubber Track Loader
Table of Contents
12. Engine 16. Hydraulic Component Service

Personal Safety . . . . . . . . . . . . . . . . . . . . . . 12-1 Personal Safety . . . . . . . . . . . . . . . . . . . . . . 16-1
Removal & Installation . . . . . . . . . . . . . . . . . 12-1 Disassembly & Assembly . . . . . . . . . . . . . . . 16-1
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1 Hydraulic Cylinder . . . . . . . . . . . . . . . . . . . 16-1
Removal Procedure . . . . . . . . . . . . . . . . 12-1 Disassembly Procedure . . . . . . . . . . . . . 16-1
Installation Procedure . . . . . . . . . . . . . . 12-2 Assembly Procedure . . . . . . . . . . . . . . . 16-3
Exhaust System . . . . . . . . . . . . . . . . . . . . 12-2 Lift Arm Control Valve . . . . . . . . . . . . . . . . 16-4
Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . 12-4 Drive Motor (brake portion) . . . . . . . . . . . . 16-6
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-5 Drive Motor (motor portion) . . . . . . . . . . . . 16-8
Drive Pump (Drive Relief Valves) . . . . . . . 16-9
13. Undercarriage Disassembly & Adjustment . . . . . . . . . . 16-9
Chapter Overview . . . . . . . . . . . . . . . . . . . . . 13-1 Posi-Power Relief Valve . . . . . . . . . . . . . 16-9
Personal Safety . . . . . . . . . . . . . . . . . . . . . . 13-1 Drive Pump . . . . . . . . . . . . . . . . . . . . . . . . 16-10
Machine Preparation . . . . . . . . . . . . . . . . . . . 13-1 Disassembly Procedure . . . . . . . . . . . . . 16-10
Removal & Installation . . . . . . . . . . . . . . . . . 13-1 Assembly Procedure . . . . . . . . . . . . . . . 16-12
15” Idler Wheel (PT-80) . . . . . . . . . . . . . . . 13-1 Auxiliary Pump . . . . . . . . . . . . . . . . . . . . . 16-14
15” & 10” wheel (PT-70) . . . . . . . . . . . . . . 13-3
Removal & Installation Procedures . . . . 13-3 17. Hydraulic Pressure & Flow
10” Bogie Wheel & Hub (PT-80) . . . . . . . 13-3 Chapter Overview . . . . . . . . . . . . . . . . . . . . . 17-1
Removal & Service Procedure . . . . . . . . 13-3 Personal Safety . . . . . . . . . . . . . . . . . . . . . . 17-1
Idler Hub . . . . . . . . . . . . . . . . . . . . . . . . . . 13-8 Contamination Inspection . . . . . . . . . . . . . . . 17-1
Removal & Service Procedure . . . . . . . . 13-8 Pressure/Flow Test and Troubleshooting . . . 17-1
Charge Pressure Check & Adjust . . . . . . . 17-1
14. Lift Arm Components Auxiliary Pressure Check & Adjust . . . . . . 17-3
Chapter Overview . . . . . . . . . . . . . . . . . . . . . 14-1 Lift Arm Pressure Check . . . . . . . . . . . . . . 17-4
Personal Safety . . . . . . . . . . . . . . . . . . . . . . 14-1 Drive Pressure Check . . . . . . . . . . . . . . . . 17-4
Machine Preparation . . . . . . . . . . . . . . . . . . . 14-1 Troubleshooting . . . . . . . . . . . . . . . . . . . 17-5
Removal & Installation . . . . . . . . . . . . . . . . . 14-1 Posi-Power Pressure Check & Adjust . . . . 17-5
Lift Cylinder . . . . . . . . . . . . . . . . . . . . . . . . 14-1 Auxiliary Flow Test . . . . . . . . . . . . . . . . . . . 17-6
Removal Procedure . . . . . . . . . . . . . . . . 14-1 Troubleshooting . . . . . . . . . . . . . . . . . . . 17-7
Installation Procedure . . . . . . . . . . . . . . 14-3
Bucket/Tilt Cylinder . . . . . . . . . . . . . . . . . . 14-3 18. Troubleshooting
Removal Procedure . . . . . . . . . . . . . . . . 14-3 Chapter Overview . . . . . . . . . . . . . . . . . . . . . 18-1
Installation Procedure . . . . . . . . . . . . . . 14-5 Personal Safety . . . . . . . . . . . . . . . . . . . . . . 18-1
Q/C Block PRV . . . . . . . . . . . . . . . . . . . . . 14-5 Visual Inspection . . . . . . . . . . . . . . . . . . . . . . 18-1
Removal Procedure . . . . . . . . . . . . . . . . 14-5 General Troubleshooting Scenarios . . . . . . . 18-1
Installation Procedure . . . . . . . . . . . . . . 14-5 Engine/Machine Troubleshooting . . . . . . . . . 18-3
15. Quick Attach 19. Lubricant and Fuel Specifications

Personal Safety . . . . . . . . . . . . . . . . . . . . . . 15-1 Fluids & Fuel Specifications . . . . . . . . . . . . . 19-1
Machine Preparation . . . . . . . . . . . . . . . . . . . 15-1
Removal & Installation . . . . . . . . . . . . . . . . . 15-1 20. Service Aids and Supplements
Locking Pin . . . . . . . . . . . . . . . . . . . . . . . . 15-1 General Torque Specifications . . . . . . . . . . . 20-1
Removal Procedure . . . . . . . . . . . . . . . . 15-1 Electrical Schematic . . . . . . . . . . . . . . . . . . . 20-2
Installation Procedure . . . . . . . . . . . . . . 15-2 Hydraulic Schematic . . . . . . . . . . . . . . . . . . . 20-3
Pivot Pin . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3
Removal Procedure . . . . . . . . . . . . . . . . 15-3
Installation Procedure . . . . . . . . . . . . . . 15-3
III
IV
1. Product Safety
Note: This label is used to provide important additional infor-

Chapter Overview mation, further explanation, comments or to stress the impor-
This chapter contains product safety information for the tance of a topic.
PT-70/80 Rubber Track Loaders. Read and understand
all product safety information before attempting to The person(s) in charge of servicing a Rubber Track
service any Rubber Track Loader. Loader may be unfamiliar with many of the systems on
the machine. This makes it especially important to use
Safety Messages caution when performing service tasks. Familiarize
Safety messages are included in this document to yourself with the affected system(s) and components
serve as warnings of potentially dangerous conditions. before attempting any type of maintenance or service.
Failure to follow their instructions could result in injury
or death. It is not possible to anticipate every potential haz-
ard. The safety messages included in this docu-
These messages are identified by the headings: ment and displayed on the machine are not all-
!DANGER!….!WARNING!….!CAUTION!. inclusive. They are intended to make you aware of
potential risks and encourage a safe approach to
The messages are to be understood as: performing service work. If you use a tool, proce-
Attention! Your Safety Is Involved! dure, work method or operating technique that is
not specifically recommended by ASV, you must
The information that follows each heading describes satisfy yourself that it is safe for you and others.
the potential hazard and the precautions necessary to You must also ensure that the machine will not be
protect yourself and others from injury. Instructions damaged or be made unsafe by the operation,
may be written or pictorially presented. lubrication, maintenance or repair procedures that
you choose.
!DANGER!
Basic Precautions
This symbol is used to alert service personnel of an
imminently hazardous situation that will result in serious !WARNING!
injury or death.
Improper or incomplete maintenance/repair of a Rubber
Track Loader can be dangerous and may result in
!WARNING! machine damage, injury or even death.
This symbol is used to alert service personnel of a
Do not attempt to perform any type of repair or mainte-
potentially hazardous situation that could result in seri-
nance on a Rubber Track Loader until you have read and
ous injury or death. fully understood the information in this manual.
!CAUTION! Refer to the Operation and Maintenance manual for

instructions regarding proper machine operation tech-
This symbol is used to alert service personnel of an niques before operating any Rubber Track Loader.
unsafe practice that could result in injury.
Following is a list of basic precautions that should
always be observed.
Information Messages
Information messages are also included in this docu- Safety Labels
ment to supplement the instructions and photographs Safety labels are displayed in various places through-
in each chapter. These messages are identified by the out the machine to serve as warnings of potentially
labels NOTICE or Note. dangerous conditions. Read and understand all
"Safety" labels on any Rubber Track Loader before
NOTICE attempting to operate, maintain or repair it. Replace
This label is used to alert service personnel of a situation
any damaged, illegible or missing labels as necessary.
that could lead to equipment or machine damage.
1-1
Rubber Track Loader
1. Product Safety
Protective Equipment Batteries

Always wear appropriate protective equipment for Do not smoke when inspecting the battery electrolyte
working conditions when working on or around a level. Never disconnect any charging unit circuit or bat-
Rubber Track Loader. Wear hard hats, protective tery circuit cable from the battery when the charging
glasses, safety shoes and any other equipment nec- unit is operating. A spark can cause an explosion from
essary to ensure your safety and the safety of others the flammable vapor mixture of hydrogen and oxygen
as you work. In particular, wear protective glasses that is released from the electrolyte through the battery
when pounding on any part of the machine or its outlets. Do not let electrolyte solution make contact
attachment with a hammer or sledge. Do not wear with skin or eyes. Electrolyte solution is an acid. In
loose clothing or jewelry that can catch on components case of contact, immediately wash skin with soap and
and cause injury. If welding is required, use welding water. For eyes, flush with large amounts of water for
gloves, helmet (UV eye protection), apron, boots and at least 15 minutes. Call Physician. Keep out of reach
any other protective clothing necessary to ensure your of children.
safety and the safety of others while welding. Avoid
wearing flammable or heat sensitive clothing while per- Pressurized Items
forming tasks that involve welding. 1. Do not use hands or any other body part to check
for fluid leaks in the hydraulic system. Always use
Entering and Exiting a solid material like wood or metal to check for this
Always use steps and handholds when entering or type of leak. Leaking fluid under pressure can pen-
exiting a Rubber Track Loader. Clean any mud or etrate body tissue. Fluid penetration can cause
debris from steps or work platforms before using them. serious injury and even death. If fluid is injected
Always face the machine when using steps and hand- into your skin, get treatment immediately. Seek
holds. When it is not possible to use the designed treatment from a doctor that is familiar with this
entry/exit system, utilize ladders, scaffolds, or work type of injury.
platforms to safely gain access to the machine.
2. Relieve pressure from the hydraulic system before
Lifting disconnecting or removing any lines, fittings or
Use a hoist when lifting components that weigh 23 kg related items. Do this by relaxing all hydraulic
(50 Ib) or more, to avoid back injury. Make sure all actuators. If the lift arms are raised, make sure
chains, hooks, slings, etc., are in good condition and they are securely braced. Be alert for possible
are of the correct capacity. Be sure hooks are posi- pressure release when disconnecting any device
tioned correctly and equipped with a spring latch. from a pressurized system.
Lifting eyes are not to be side loaded during a lifting
operation. 3. Lower the lift arms before performing any work on
the machine. If this cannot be done, make sure
they are securely braced to prevent them from
Hot Fluids and Components dropping unexpectedly during service.
Stay clear of hot components and system fluids of the
engine, exhaust, radiator/oil cooler and hydraulic 4. Loose or damaged fuel, oil, hydraulic, lines, tubes
lines/tubes. Also, use caution when removing fill caps, and hoses can cause fires. Do not bend or strike
breathers and plugs on the machine. Hold a rag over high pressure lines or install ones that have been
the cap or plug to prevent being sprayed or splashed bent or damaged. Check lines, tubes and hoses
by liquids under pressure. Be especially careful if the carefully. See item 1 for precautions on checking
machine has been operated recently, fluids may still be for fluid leaks.
hot. To ensure your safety, allow the machine to cool
before attempting any service procedure that involves 5. Pressurized air or water can also cause injury.
hot fluids or components. When pressurized air or water is used for clean-
ing, wear a protective face shield, protective cloth-
Corrosion Inhibitor ing, and protective shoes. The recommended max-
Corrosion inhibitor contains alkali. Avoid contact with imum air pressure for cleaning purposes is 205
eyes. Avoid prolonged or repeated contact with skin. kPa (30 psi). When using a pressure washer, keep
Do not take internally. In case of contact, wash skin in mind that nozzle pressures are typically very
immediately with soap and water. For eyes, flush with high. Generally, pressures are well above 13790
large amounts of water for at least 15 minutes. Call kPa (2000 psi). Follow all recommended practices
Physician. Keep out of reach of children. provided by the pressure washer manufacturer.
1-2
Rubber Track Loader
1. Product Safety
Repair cause bodily injury, death or property damage. Be

prepared to shut off the fuel and air supply to the
!WARNING! engine in order to stop the engine.
Accidental machine starting can cause injury or even
death to personnel working on a Rubber Track Loader. 9. Be careful when removing cover plates. Gradually
back off the last two bolts or nuts located on oppo-
As a precaution, disconnect the battery cables from the site sides of the cover. Then, pry the cover loose
battery terminals, tape the battery clamps and remove to relieve any spring or other pressure before
the key from the ignition switch prior to performing any removing the last two nuts or bolts completely.
service work on a Rubber Track Loader.
10. Repairs requiring welding should be performed
Place a “Do Not Operate” tag prominently on the
only by personnel adequately trained and knowl-
machine to inform personnel that the machine is being
serviced.
edgeable in welding procedures and with the guid-
ance of appropriate reference information.
1. Disconnect the battery and discharge any capaci- Determine the type of metal being welded and
tor before beginning work on a machine. Attach a select the correct welding procedure and filler
Do Not Operate tag in the cab to alert any opera- material to provide a weld that is as strong or
tor that service is in progress. stronger than the original weld.
2. If possible, make all repairs with the machine 11. Take precautions to avoid damaging wiring during
parked on a level, hard surface. Use blocks to pre- removal and installation operations. Carefully route
vent the machine from rolling while working on or wires so that they will not contact sharp corners,
under the machine. objects or hot surfaces during operation.
3. Do not work on or under any machine that is sup- 12. When performing service that requires the lift arms
ported only by a hydraulic jack or hoist. Always to be in the raised position, always utilize the lift
use some sort of mechanical support to ensure arm brace located on the rear of the loader tower.
that the machine will not fall. ASV jack stands work
well to support the machine while performing 13. Relieve hydraulic system pressure by relaxing all
maintenance or repair work. hydraulic actuators prior to attempting any
hydraulic maintenance or repair.
4. Make sure the work area around the machine is
safe and make yourself aware of any hazardous 14. Always tighten connections to the correct torque
conditions that may exist. If the engine needs to specification. Make sure that all shields, clamps
be started inside an enclosure, make sure that the and guards are installed correctly to avoid exces-
engine’s exhaust is properly vented. sive heat, vibration or unwanted contact between
parts during operation. Shields that protect
5. Be sure all protective devices including guards and exhaust components from oil spray in event of a
shields are properly installed and functioning cor- line, tube or seal failure must be correctly installed.
rectly before beginning any service task. If a guard
or shield must be removed to perform the repair 15. Do not operate a machine if any rotating part is
work, use extra caution. damaged or contacts other parts during operation.
Any high speed rotating component that has been
6. Always use the appropriate tools for the work to be damaged or altered should be checked for balance
performed. Tools should be in good condition and before reusing. Make sure all protective devices,
you should understand how to use them properly including guards and shields, are properly installed
before performing any service work. and functioning correctly before starting the engine
or operating the machine.
7. When replacing fasteners, use parts of equivalent
grade and size. Do not use a lesser quality fasten- Attachments
er if replacements are necessary. Only use attachments that are recommended by ASV.
8. Be prepared to stop an engine if it has been re- Make sure that all necessary guards and protective
cently overhauled or the fuel system has been equipment are in place and functioning prior to operat-
recently serviced. If the engine has not been ing any attachment.
assembled correctly, or if the fuel settings are not
correct, the engine can possibly overspeed and
1-3
Rubber Track Loader
1. Product Safety
Wear protective glasses and protective equipment as 6. Stay away from areas that might have asbestos
required by conditions or as recommended in the particles in the air.
attachment’s operation manual.
Ensure that all personnel are far enough away from !WARNING!
the work area so they will not be struck by flying ob-
When replacement parts are required for your machine,
jects.
use only genuine ASV replacement parts or parts that
meet or exceed original specifications including, but not
Stay clear of the cutting edges, pinching surfaces or limited to physical dimensions, type, strength and mate-
crushing surfaces of the attachment while performing rial.
any attachment maintenance, testing or adjustments.
Installing lesser components can lead to premature fail-
ures, product damage, personal injury or death.
Asbestos Information
Equipment and replacement parts shipped from the
manufacturer are asbestos free. When replacement Machine Labels and Decals
parts are required, use only genuine manufacturer’s Labels and decals placed on the machine provide
replacement parts safety information and operating instructions.
Familiarize yourself with the location and significance
Use caution when handling replacement parts from of these labels to ensure your safety.
another supplier if these parts contain asbestos. Avoid
inhaling dust that might be generated when handling Product Identification Number
these components or when handling asbestos debris. The Product Identification Number (PIN) is located on
Inhaling this dust can be hazardous to your health. the front of the cab enclosure in the lower right corner.
(figure 1-1). Always provide the PIN when contacting
The components that may contain asbestos fibers are the dealer about parts, service, warranty or acces-
lining material, and some gaskets. The asbestos that is sories. No warranty claims will be processed unless
used in these components is usually encased in a the PIN is provided.
resin or sealed in some way. Normal handling is not
hazardous unless airborne dust containing asbestos is
generated.
If dust that may contain asbestos is present, there are

several guidelines that should be followed.
1. Never use compressed air for cleaning. Avoid

brushing or grinding materials that contain as- 1-1
bestos. Use a wet method to clean up asbestos
debris. A vacuum that is equipped with the high-
efficiency particulate air filter (HEPA filter) can also
be used. Engine Serial Number
The engine serial number is located on the top of the
2. Use exhaust ventilation on permanent machining engine valve cover near the rear of the machine.
jobs. (figure 1-2)
3. Wear an approved respirator if there is no other

way to control the dust. Model ID Tag
4. Comply with applicable rules and regulations for

the work place. In the USA, use Occupational
Safety and Health Administration requirements.
These OSHA requirements can be found in 29
CFR 1910.1001. 1-2 Serial # Tag
5. Obey environmental regulations for disposal of

asbestos.
1-4
Rubber Track Loader
1. Product Safety
Machine Label and Decal Examples

2-Speed WARNING
Examples of the labels and decals displayed on the
(if equipped)
machine are shown on this page. To engage: Entering & Exiting
Press the button located Maintain 3-point contact
on the front of the right with step and hand rails.
joystick control.
DANGER
Pre-Start Checklist
To disengage: 1. Operator seated in
Press the button a sec- cab.
ond time. 2. Seat belt fastened.
3. Lap bar pivoted down.
WARNING 4. Joystick controls in
neutral position.
Brushcutting
5. Quick attach switch in
Brushcutting, mowing or
locked position.
operations that generate
airborne debris can 6. High & low flow auxil-
cause fires. iary switches off.
With the engine off Engine Warm-Up

and cool: Allow the engine to
1. Inspect the engine warm up prior to opera-
compartment and any tion.
Keep out from under raised lift arms! other areas containing
hot or rotating parts Carrying Loads
Do not go beneath raised lift arms unless the lift arm Carry loads low. Load,
brace has been properly installed. See operation and 2. Thoroughly clean
unload and turn on level
maintenance manual for installation procedure. these areas as often
ground.
as necessary to
avoid combustion.
Failure to observe or comply with warnings may result in Inclines
serious injury or even death. Failure to do so could Travel with heaviest end
2045-466
result in fire that may of machine facing uphill.
cause machine damage,
personal injury, or even
Riders
death. 2045-468 Riders not permitted.
Work Platform
Never use a work tool as
NEVER GO BENEATH UNSECURED LIFT ARMS a work platform.
WARNING 1. Remove any attachment from the machine.
2. Have an assistant remove the lift arm brace from its stowed position. Disclaimer
3. Start the engine and carefully raise the lift arms.
4. Have the assistant install the brace around the exposed portion of the lift cylinder rod. Failure to observe and
Follow instructions closely! 5. Have the assistant secure the brace to the rod with the retaining pins, then stand clear.
6. Slowly lower the lift arms until they come to rest on the brace.
comply with the warn-
Failure to install lift arm brace correctly ings listed above may
7. Shut the engine off and carefully exit the machine.
may result in personal injury or death. 8. Reverse this procedure to lower and re-secure the lift arm brace. result in machine dam-
2045-646
age, personal injury, or
even death. 2045-469
WARNING Keep away from tracks while machine is in motion.

Serious personal injury or even death may result.
DANGER
Prior to Operating
CAUTION
Inspect undercarriages daily for accumulation of
debris. Build-up of debris may shorten component Read and fully under-
life and decrease machine performance. 2045-467
stand the operation and
maintenance manual
prior to operating this
machine.
Operating Position
Never operate the
machine with any part of
your body protruding
out of the operator
enclosure.
Failure to do so may
result in serious injury or
even death. 2045-472
1-5
1-6
2. Technical Specifications
& Service Tools
PT-80 Specifications Oil Cooler

- Operating pressure: 150 psi (1034 kPa)
Engine - Bypass relief pressure: 80 psi (689 kPa)
- Model: Perkins 804C-33T - Hot oil sending unit: 225°F (107.2°C)
- Displacement: 3.3 liter - Avg. oil operating temp. 50-60°F above ambient.
- Gross horsepower: 80.5 hp (60 kW) (High flow application 80°F above ambient.)
- Torque: 186 lb-ft. (253 Nm)
- Idle rpm: 1000 (low idle), 2600 (high idle) Critical Torque Specs
- Average water /thermostat temperature: 190°F, - Transmission Mounting Bolts
87.8°C -- 85 ft-lb. w/Blue Loctite
- Drive Sprocket Drive Teeth Bolts
Transmission -- 88 ft-lb. -Dry
- Model: Cat A22VG45 tandem (Rexroth) - Bogie Wheel (10” Idler) Retaining Bolt
-- 180 ft-lb. - w/Red Loctite
- 15” Idler Wheel Retaining Nut
Drive Pumps
-- 350 ft-lb. -Dry
- Displacement: 2.7459 in3/rev (45 cc/rev)
- Drive Sprocket Lug Nut
- Relief pressure: 5500 psi (380 bar)
-- 206 ft-lb. -Dry
- Flow: 30.91 gpm (117 lpm) @ 2600 rpm (per
- Drive Motor Mounting Bolts
pump)
-- 206 ft-lbs. -Dry
Charge Pump
- Displacement: 1.373 in3/rev (22.5 cc/rev) Cycle Times
- Relief pressure: 475 +/- 30 psi (32.75 bar) • Lift-Arm up: 3.5 seconds (+/- .35 seconds)
- Flow: 15.4 gpm (58.3 lpm) @2600 rpm • Lift-Arm Down: 3.3 seconds (+/- .33 seconds)
• Bucket Curl: 1.7 seconds (+/- .17 seconds)
Drive Motors • Bucket Dump: 1.9 seconds (+/- .19 seconds)
- Model: Rexroth MCR 5
- Displacement: 50 in3/rev (820 cc/rev)
Service Tools
Pilot Controls (Joysticks) Listed below are common service tools which are iden-
- Model: Rexroth 08-351 tified and utilized in the service procedures described
in this manual. Use tools recommended by ASV when-
ever possible to reduce risk of injury and or machine
Auxiliary Pump damage during service.
- Make: Rexroth
- Type: Axial Piston, Variable Load Sense • ASV Jack Stands (2) (ASV P/N: 0402-900)
- Displacement: 2.75 in3/rev (45 cc/rev) • Heavy Duty Hydraulic Jack (5-ton rating)
- Max Flow: 30 gpm (113.6 lpm) @ 2600 rpm • Test Gauge Kit (ASV P/N: 0402-935)
- Relief pressure: 3000 psi (20,680 kPa) • Ratchet Strap
- Marginal (Standby) Pressure: 218 psi (1,503 kPa) • Long Pry Bar(s)
- Cooling/filtering: Oil is filtered and cooled at all • ASV Service Cart (0402-871)
times. In auxiliary mode, the oil is filtered after the
attachment to protect the machine if the attach-
ment motor fails or contaminants are introduced
from the quick couplers.
Lift Arm Control Valve

- Make: Rexroth
- Type: Load Sense
2-1
Rubber Track Loader
2. Technical Specifications & Service Tools
PT-70 Specifications Oil Cooler

- Operating pressure: 150 psi (1034 kPa)
Engine - Bypass relief pressure: 80 psi (689 kPa)
- Model: Perkins 804C-33T - Hot oil sending unit: 225°F (107.2°C)
- Displacement: 3.3 liter - Avg. oil operating temp. 50-60°F above ambient.
- Gross horsepower: 71 hp (53 kW) (High flow application 80°F above ambient.)
- Torque: 173 lb-ft. (234 Nm)
- Idle rpm: 1000 (low idle), 2600 (high idle) Critical Torque Specs
- Average water /thermostat temperature: 190°F, - Transmission Mounting Bolts
87.8°C -- 85 ft-lb. w/Blue Loctite
- Drive Sprocket Drive Teeth Bolts
Transmission -- 88 ft-lb. -Dry
- Model: Cat A22VG45 tandem (Rexroth) - 10” Idler Wheel Retaining Nut
-- 350 ft-lb. -Dry
- 15” Idler Wheel Retaining Nut
Drive Pumps
-- 350 ft-lb. -Dry
- Displacement: 2.7459 in3/rev (45 cc/rev)
- Drive Sprocket Lug Nut
- Relief pressure: 5500 psi (380 bar)
-- 129 ft-lb. -Dry
- Flow: 30.91 gpm (117 lpm) @ 2600 rpm (per
- Drive Motor Mounting Bolts
pump)
-- 129 ft-lbs. -Dry
Charge Pump
- Displacement: 1.373 in3/rev (22.5 cc/rev) Cycle Times
- Relief pressure: 475 +/- 30 psi (32.75 bar) • Lift-Arm up: 3.5 seconds (+/- .35 seconds)
- Flow: 15.4 gpm (58.3 lpm) @2600 rpm • Lift-Arm Down: 3.3 seconds (+/- .33 seconds)
• Bucket Curl: 1.7 seconds (+/- .17 seconds)
Drive Motors • Bucket Dump: 1.9 seconds (+/- .19 seconds)
- Model: Rexroth MCR 05 C
- Displacement: 37.8 in3/rev (620 cc/rev) Service Tools
Listed below are common service tools which are iden-
Pilot Controls (Joysticks) tified and utilized in the service procedures described
- Model: Rexroth 08-351 in this manual. Use tools recommended by ASV when-
ever possible to reduce risk of injury and or machine
damage during service.
Auxiliary Pump
- Make: Rexroth • ASV Jack Stands (2) (ASV P/N: 0402-900)
- Type: Axial Piston, Variable Load Sense • Heavy Duty Hydraulic Jack (5-ton rating)
- Displacement: 2.75 in3/rev (45 cc/rev) • Test Gauge Kit (ASV P/N: 0402-935)
- Max Flow: 30 gpm (113.6 lpm) @ 2600 rpm • Ratchet Strap
- Relief pressure: 3000 psi (20,680 kPa) • Long Pry Bar(s)
- Marginal (Standby) Pressure: 218 psi (1,503 kPa) • ASV Service Cart (0402-871)
- Cooling/filtering: Oil is filtered and cooled at all
times. In auxiliary mode, the oil is filtered after the
attachment to protect the machine if the attach-
ment motor fails or contaminants are introduced
from the quick couplers.

- Make: Rexroth
- Type: Load Sense
2-2
3. Circuit Diagrams
Chapter Overview Hydraulic Charge Circuit

This chapter contains diagrams for the following PT-
70/80 circuits: hydraulic charge circuit, hydraulic auxil-
iary circuit, hydraulic drive circuit, loader valve,
hydraulic pilot generation (solenoid) block and electri-
cal attachment outlet. It also contains hose routing
information for the control configurations for the drive
and lift arm pilot controls.
Figure 3-1 PT-70/80 Hydraulic Charge Circuit
OIL COOLER
CHECK VALVE
(15 PSI) CHECK VALVE
(0 PSI)
TO HYD Q/A (OPTIONAL PT-70)
CHARGE PRESSURE
RELIEF VALVE
(475 +/- 30 PSI) TANK CHARGE PRESSURE
FLOW TEST PORT
(475 +/- 30 PSI)
CHARGE PUMP
TANK
PILOT GEN BLOCK TANK
INLET
5 MICRON FILTER
3-1
Rubber Track Loader
3. Circuit Diagrams
Hydraulic Auxiliary Circuit
Figure 3-2 PT-70/80 Hydraulic Auxiliary Circuit
OIL COOLER
TO ATTACHMENT
CASE DRAIN Q/C
TO TANK CHECK VALVE
(80 PSI)
TO BUCKET CYL. FLOW
TO TANK
LOADER CONTROL
TO LIFT ARM CYL.
TO AUXILIARY Q/C
TO LIFT ARM CYL.
LIFT ARM VALVE
TO TANK
LOAD SENSE
AUXILIARY PUMP
CHARGE PUMP INLET
PILOT GEN. BLOCK AUXILIARY PUMP INLET
3-2
Rubber Track Loader
3. Circuit Diagrams
Hydraulic Drive Circuit
Figure 3-3 PT-70/80 Hydraulic Drive Circuit
DRIVE PRESSURE
RELIEF VALVES (4)
5500 PSI
DRIVE CONTROL
DRIVE MOTOR DRIVE PUMP
DRIVE MOTOR
CASE DRAIN
TO COOLER
TANK
BRAKE
2-SPEED SHIFT (PT-80)
3-3
Rubber Track Loader
3. Circuit Diagrams
Figure 3-4 PT-70/80 Lift Arm Control Valve
RELIEF VALVE SETTINGS
(B3) 3307 PSI (A3) 3307 PSI
(B2) 3147 PSI (A2) 3669 PSI
(B1) 3640 PSI (A1) Anti-Cavitation

Check Valve
3-4
Rubber Track Loader
3. Circuit Diagrams
Hydraulic Pilot Generation

Block
Figure 3-5 PT-70/80 Hyd. Pilot Generation Block
3-5
Rubber Track Loader
3. Circuit Diagrams
Electrical Attachment Outlet
Figure 3-6 PT-70/80 Electrical Attachment Outlet
3-6
Rubber Track Loader
3. Circuit Diagrams
Drive Control
(line routing)
Figure 3-7 PT-70/80 Standard Drive Control
3-7
Rubber Track Loader
3. Circuit Diagrams
Lift Arm Control

(line routing)
Figure 3-8 PT-70/80 Lift Arm Control
3-8
4. Maintenance
Chapter Overview Lift Arm Brace

This chapter provides information on general mainte- The lift arm brace (A) is intended to keep service per-
nance procedures for the PT-70/80. If there is an issue sonnel safe when it is necessary to work on a machine
that requires troubleshooting, refer to Chapter 18, with the lift arms in the raised position. It is not safe to
Troubleshooting. rely on the hydraulic system to hold the lift arms in the
raised position just as it is not safe to crawl under a
Personal Safety machine supported only by a jack. The lift arm brace is
used to support the weight of the lift arms much like
!WARNING! jack stands are used to mechanically support vehicle
Improper or incomplete maintenance/repair of a Rubber weight.
machine damage, injury or even death. To install the lift arm brace:
1. Park the machine on level ground in a safe area
Do not attempt to perform any type of repair or mainte- for performing service work.
nance on a Rubber Track Loader until you have read and 2. Remove any attachments that may be fastened to
fully understood the information in this manual. the quick attach.
Refer to the Operation and Maintenance manual for 3. Have an assistant remove the retaining pins (B)
instructions regarding proper machine operation tech- securing the lift arm brace and remove it from the
niques before operating any Rubber Track Loader. machine.
4. Make sure bystanders are clear of the lift arms,
Prior to performing any type of service work on a then raise them to the upper limit.
Rubber Track Loader, read and understand Chapter 1
5. Have an assistant Install the brace around the
(Product Safety) for personal safety information.
cylinder shaft as shown and reinstall the pins to
secure it to the cylinder.
6. Lower the lift arms slowly until they come to rest
on the brace.
7. It is now safe to shut the engine off and exit the
machine.
!WARNING!
Do not work on or near the machine with the lift arms in
A
the raised position unless the lift arm brace has been
correctly installed.
To remove the lift arm brace:

4-1
1. Start the machine and raise the lift arms until they
are clear of the brace.
2. Once clear, have an assistant remove the brace
from the cylinder and stow it on the machine with
the pins.
B
3. Once the brace has been stowed and the assistant
is clear of the lift arms, lower the arms to the
ground and shut the engine off to complete the
procedure.
4-2
4-1
Rubber Track Loader
4. Maintenance
4-4
4-3
Tilt-Up Cab
The ROPS/FOPS approved cab (A) tilts up to allow
easier access while performing maintenance. It fea-
tures a gas spring assist and a brace mechanism to
hold it in place while tilted.
To tilt the cab:
1. Remove any attachments that may be fastened to
the machine. 4-5
2. (Optional) Raise the lift arms and secure them with
the lift arm brace. (See page 4-1.) Jacking Procedure
Occasionally, your machine may need to be suspend-
3. Remove the two bolts that fasten the cab to the
ed off of the ground to perform maintenance. Exercise
chassis. They are located inside the cab, one in
caution when jacking the machine. Always use a jack
each of the front corners.
that is capable of lifting the machine and support its
4. Once the bolts have been removed, tilt the cab weight with ASV approved jack stands while suspend-
slowly upwards. The cab brace (B) should fall ed. Never work on or under a machine supported only
onto the shoulder bolt (C) locking the cab in its by a jack.
upright position.
To safely jack your machine:
The cab is now secure.
1. Remove any attachments that may be fastened to
To lower the cab: the machine and raise the lift arms.
1. Raise the cab brace so that the locking channel is 2. Install the lift arm brace as instructed on page 4-1.
clear of the shoulder bolt.
3. Once the lift arms are secured, carefully exit the
2. Hold the brace upwards and lower the cab until the machine.
locking channel is clear of the shoulder bolt then
4. Roll or slide your jack under the front of the
release the brace.
machine and center the lifting pad directly under
3. The cab is now free to be lowered into operating the middle of the front torsion axle.
position.
5. Once in place, jack the machine upward making
4. Lower the cab completely and then fasten it to the sure it remains stable until it has reached sufficient
chassis with the two bolts removed previously. height to install an ASV jack stand beneath the
machine. (fig. 4-4)
6. Slide the jack stand into place making sure it is
centered under the machine (left to right when
viewed from the front) and far enough back for the
machine to remain stable when the jack is lowered
and the front of the machine rests on the stand.
(fig. 4-5)
7. Once the stand is in place, slowly lower the
machine onto the stand and then remove the jack.
Repeat steps 4-7 at the rear of the machine should
both ends of the machine need to be off of the ground
for service.
4-2
Rubber Track Loader
4. Maintenance
Grease Fitting Locations

A. Lower Bucket Cylinder Pivot (2)
D
B. Upper Bucket Cylinder Pivot (2)
C. Front Lift Cylinder Pivot (2) E
D. Lift Arm Pivot (2) C
E. Rear Lift Cylinder Pivot (2) B
F. Rear Axle Pivot (2)
G. Front Axle Pivot (2)
H. Lower Bucket Pivot (2) A
4-6 H
F
G
Grease Fittings
The PT 70/80 are equipped with grease fittings at pivot points throughout the machine. The illustration above
shows the locations of all fittings on the left side of the machine. An identical fitting exists on the right side of the
machine for each one identified in the illustration. Lubricate all fittings DAILY or after every 10 hours of operation
to maximize component life and ensure proper machine function. (fig. 4-6)
Undercarriages
The undercarriage assemblies in Rubber Track Loaders typically operate in harsh working conditions. They
work in mud, gravel, debris and various other abrasive materials during operation. ASV recommends a daily
inspection of the undercarriage assemblies and cleaning if necessary.
Materials that are particularly sticky or abrasive like clay, mud, or gravel should be cleaned from the undercar-
riages more often to minimize component wear. A pressure washer works well for cleaning materials from the
undercarriages. At times when a pressure washer is not available, use a bar, shovel or similar device to remove
foreign materials.
When cleaning, pay particular attention to the drive tables, sprockets, and the front and rear wheels where
debris is likely to accumulate. If working in scrap or debris, inspect more often and remove foreign objects that
may wrap around or lodge themselves between components causing premature wear and damage.
Operation in loamy sand or on turf or other finished surfaces may require less frequent cleaning, but daily
inspection is still advised.
4-3
Rubber Track Loader
4. Maintenance
Track Tension (PT-70/80)

Straight-Edge Proper track tension must be maintained for optimal
performance and track/undercarriage life. Running a
track that is too loose may cause the track to misfeed
possibly causing damage to the track and or undercar-
riage components. Running a track that is too tight
may cause track stretch, premature bearing failure, or
other preventable damage to the machine. As a rule, a
track should only be tightened to the point where there
is no visible sag. Never tighten your tracks beyond this
point.
4-7
Note: During the first 50 hours of operation the tracks
will "break-in" and will most likely require adjustment.
To check track tension: (fig. 4-7, 4-8)
1. Drive the machine forward 5 feet to remove belt
slack from the lower and rearward portions of the
track.
2. Lay a straight edge along the top of the track
bridging the drive sprocket and front idler wheel.
3. Apply 90 lbs. of down force to the the track by
either placing weight on top or hanging it using
rope or wire midway between the drive sprocket
4-8 and front idler.
4. Measure from the bottom of the straight edge to
the lug surface (top) of the track. The deflection
should measure between 3/4" and 1".
To adjust track tension: (fig. 4-9)
B 1. Loosen the lock nut (A) on the turnbuckle (B) and
adjust by turning the turn buckle itself until proper
tension has been achieved.
2. Then tighten the turnbuckle lock nut to complete
A
the procedure.
3. Repeat the adjustment procedure on the other side
of the machine if necessary.
4-9
4-4
Rubber Track Loader
4. Maintenance
PT-70 PT-80
F
F
C
E
D
J
Steel Pin
I
H (.088”)
G
K
B New Roller Normal Wear

4-10 A
35% life
Drive Sprocket Rollers Note: You may need to pry or lift the track upwards
ASV rubber track loaders utilize rollers on the drive with a hoist above the drive sprocket to provide clear-
sprockets to drive the track. These rollers help mini- ance for removal.
mize friction between the track and the drive sprocket 7. Remove one bolt (F) holding the steel pins (D) and
to prolong track life. rollers (E) in place. Install the new rollers over
the pins, then slide the bolt back through the
The rollers rotate around hardened steel pins and usu- sprocket and pins and secure it with the nut (K).
ally wear on their inside surfaces. As they wear, the
rollers become thinner, but will continue to function as 8. Repeat this process as required throughout the
long as they rotate freely around the pins. Sprocket sprocket.
rollers should be inspected every 50 hours of operation 9. Reinstall the sprocket by reversing steps 2-6.
and replaced if cracked or worn to less than 35% of Note: During removal of the bearing cap (step 3) the
original thickness. (.088”) bulged area of the cap is beaten inward. When rein-
To replace worn rollers: stalling, orient the cap so that the domed area is facing
outward. Then tap the center of the cap with a ball
1. Begin by performing steps 1-4 in the track removal peen hammer or similar device to reset the cap. Do
procedure on page 4-6 to allow the sprocket to be this gently. Too much inward force can damage (mush-
removed. room) the bearing shaft.
2. Remove the seven bearing plate mounting bolts 10. Repeat steps 1-9 on the other side of the machine
(A, I), then remove the plate (B) from the drive if necessary.
table.
11. Perform the track tension adjustment and check
3. Remove the bearing cap (G) by tapping around the procedures on page 4-4.
bulged area of the cap with a hammer. This will
relieve the outward pressure on the cap and allow Note: Replace rollers as a set to simplify inspection
for removal. and maintain proper sprocket function.
4. Remove the external snap ring (H) from the bear

ing shaft.
5. Using a puller, remove the bearing assembly (J)
from the shaft.
6. Remove the sprocket mounting bolts (C), then
remove the sprocket.
4-5
Rubber Track Loader
4. Maintenance
Track Removal/Installation
Tracks may need to be removed periodically to inspect
undercarriage components or for replacement if worn
or damaged. This section covers the procedure to
remove and install a track on PT 70/80 machines.
Tools required:
• Socket/impact wrench Cavity
• Ratchet strap
• Heavy duty hydraulic jack
• Combination wrench
• Long pry bar(s)
4-12
• ASV approved jack stands (2)
• Spray lubricant
• Shop vac or Pressure washer
Note: The PT-80 style undercarriage is depicted in this

procedure. The PT-70 undercarriage is very similar,
however it has only one row of stationary inner and
outer idler wheels. The track removal procedure is
identical with this exception. (fig. 4-11)
Track Removal
1. Break up and remove any foreign material from the
cavity between the suspension rail and the drive
table support. (fig. 4-12) 4-13
Note: A shop vac or pressure washer will work well to

remove material from this cavity.
2. Clean the threads on the turnbuckle thoroughly

using a stiff bristle brush.
3. Loosen the lock nut on the turnbuckle and spin it
to the end of the threaded shaft to allow clearance
when the drive table is lowered.(fig. 4-13)
4. Rotate the turnbuckle and lower the drive table as
far as it will go. (fig. 4-14)
5. Remove the bolts securing the outer front wheel to
4-14
the hub. Then remove the wheel. (fig. 4-11, 4-15,
4-16)
PT-70
BOLTS
4-15
4-11
4-6
Rubber Track Loader
4. Maintenance
4-16 4-19
6. Remove the outer scraper plate from the suspen

sion rail. (PT-80 only/fig. 4-17)
7. Remove the bolts securing the inner wheel to the
hub, then remove the wheel.
(PT-80 only/fig. 4-18, 4-19)
8. Use a pry bar to peel the track over the inner
wheel(s) toward the outside of the machine.
(fig. 4-20)
9. Once the track is off of the front wheel(s), pull the
rear of the track clear of the suspension.
(fig. 4-21, 4-22) 4-20
4-17
4-21
4-18
4-22
4-7
Rubber Track Loader
4. Maintenance
Track Installation
1. Slide the track over the drive sprocket at the rear
of the machine. (fig. 4-23, 4-24)
2. Slide the front of the track into position for installa
tion. (fig. 4-25)
3. Lubricate the inner front wheel(s) and the inside of
the front portion of the track with a spray lubricant.
(fig. 4-26)
4. Attach a ratchet strap to the upper front portion of
the track and the other end to one of the tow
hooks on the front of the machine. (fig. 4-27) 4-25
5. Tighten the strap until the track is pulled upward
slightly and in position to slide over the inner idler
wheel(s) at the front. (fig. 4-27)
6. Pull all of the slack forward and make sure the
track drive lugs are properly meshed with the
sprocket to provide as much slack as possible for
installation.
7. If you have an assistant, have them pull the track
forward while you push inward on the track. Work
the track over the wheel(s) and into place.
8. If you do not have an assistant, push the track for
ward in inward in a quick forceful motion to slide 4-26
the track into place. The ratchet strap will help to
keep the track in place while you work it over
the idler(s). (fig. 4-28)
4-27
4-23
4-28
4-24
4-8
Rubber Track Loader
4. Maintenance
9. Once the track is in position over the idler wheels,

install the inner idler wheel onto the hub and
secure it in place with the mounting bolts. Torque
them to 90 +/- 10 Lb. Ft.
(PT-80 only/fig. 4-29, 4-30, 4-31)
Note: You may need to use a bar to keep the wheel
from spinning as you torque the mounting bolts to
spec. (fig. 4-31)
10. Install the scraper onto the suspension rail and
tighten the bolts to secure it in place. (PT-80
only/fig. 4-32) 4-31
11. Install the outer idler wheel and secure it in place
with the mounting bolts. Torque them to 90 +/- 10
Lb. Ft. (fig. 4-33, 4-34)
12. Perform the track tension adjustment and check
procedures on page 4-4 to complete installation.
4-32
4-29
4-33
4-30
4-34
4-9
Rubber Track Loader
4. Maintenance
Air Cleaner
The PT 70/80 are equipped with two air filter elements
to remove contaminants from the air used for combus- A
tion. Regular inspection and replacement is necessary
to ensure proper performance and to prolong engine
life.
To remove and inspect your air cleaner elements:
1. Turn the engine off.
2. Open the hood at the rear of the machine to gain
access to the engine compartment.
4-35
3. Locate the black air cleaner enclosure near the top
left of the engine compartment (when viewed from
the rear).
4. Twist the tension screw (A) counter-clockwise until
the band is loose enough to remove the cover,
then remove the cover. The primary element (B)
should be exposed.
5. Remove the primary element and inspect it. If it
appears damaged in any way, replace it. If the ele-
ment is heavily soiled, replace it. If it appears to be
in good condition, clean if necessary and re-install.
6. Once the primary element has been removed, the
secondary element (C) should be visible. Remove 4-36
and inspect it. If the element is damaged or heavily
soiled, replace it.
Note: The secondary element is not serviceable. It

should be replaced after every three cleanings of the
primary filter.
Note: The primary element may be cleaned and reused

up to five times if properly maintained, but should be
replaced at least once a year.
B
4-37
4-38
4-10
Rubber Track Loader
4. Maintenance
Fuel Filter
The fuel filter removes contaminants from the fuel as it
enters the engine for combustion. Over time the filter
can become plugged and cause the engine to lose
power, run roughly or fail to start. The fuel filter should
be changed every 500 hours or more often if needed
to prevent these conditions from occurring.
To change the fuel filter:
1. Clean the outside of the filter assembly thoroughly
to reduce the chances of contaminants being intro
4-39 duced into the fuel system.
7. Once the inspection has been performed, install 2. Twist the water separator catch bowl (A) counter
the new secondary filter element into the enclosure clockwise (when viewed from the bottom) and
as found upon disassembly. (fig. 4-39) remove it from the assembly. Take care not to lose
the o-ring that seals it to the filter base.
8. Install the primary element by sliding it into place
in the enclosure as found upon disassembly. 3. Twist the upper lock ring (B) counter clockwise
(when viewed from the bottom) and remove it from
9. Install and secure the cover by sliding it into place the assembly.
and positioning the band over the retaining lip.
Then turn the tension screw clockwise until tight. 4. Slide the filter (C) downward to remove it. Note the
Gently wiggle the cover to make sure it is secure. position of the raised tabs on the upper portion of
the filter to simplify reassembly.
5. Install the new filter element into the assembly by
To clean your primary filter element: reversing steps 2-4.
1. Remove loose dirt from the filter element with com- Water Separator
pressed air or water hose. The water separator removes water from the fuel sup-
Compressed air: 100 P.S.I. max. 1/8" diameter ply as the engine runs. Drain the water separator daily
nozzle at least 2" away from filter. to maintain proper function.
Water: 40 P.S.I. max. without nozzle.
To drain the water separator:
2. Soak the filter in a non-sudsing detergent solution 1. Loosen the black screw on the bottom of the
for at least 15 minutes moving it gently through the separator.
solution to further clean the element. (Never soak
for more than 24 hours.) 2. Re-tighten the screw after the water has been
3. Rinse the filter thoroughly with a gentle stream of drained from the catch bowl.
water to remove all dirt and remaining detergent.
4. Allow the filter to dry completely before re-installing
it into the machine.
NOTICE
B
Do not use any heat source other than warm air at
less than 160°F to dry the filter.
C
Do not clean air filter elements while engine war-
ranty is in effect. During the warranty period, ASV
A
recommends replacing air filter elements instead 4-40
of cleaning them. Heavy-duty air filter manufactur-
ers will not warrant the air filter once it has been
cleaned.
4-11
Rubber Track Loader
4. Maintenance
Accessory Belt Tension

Drive belts typically stretch and wear during their serv-
ice life. The fan and A/C belts should be checked for
tension, condition and presence daily prior to operating
your machine.
To check fan or A/C belt tension:
1. With the engine cold and off, remove the key from
the ignition to avoid accidental start.
2. Lift the hood at the rear of the machine and check
to make sure the fan and A/C belts are present
and in good condition. If they appear excessively 4-41
worn, or cracked, replace them.
3. Lay a straight edge across the alternator and crank
pulleys (crank and A/C pulleys for A/C belt) and
apply a force of 10 lbs. midway between the pul
leys. (fig. 4-41, 4-42)
4. Measure the distance from the bottom of the
straight edge to the top surface of each belt
(deflection). Fan belt deflection should meas-
ure 3/8” (7/16” A/C) if properly tensioned.
5. If the belts are loose or tight, adjust tension until
correct.
To adjust fan or A/C belt tension: 4-42
1. Make sure the engine is cold, off, and the key has
been removed from the ignition to avoid accidental
start.
2. Lift the hood at the rear of the machine and loosen
the bolts securing the alternator or A/C pump
slightly to allow the alternator or A/C pump
to pivot. (fig. 4-43, 4-44)
Bolts
3. Once loose, use a small pry bar as a lever to force
Pry-bar
the alternator or A/C pump against the belt(s) to
increase belt tension to appropriate level then
tighten bolts to specification. (fig. 4-43, 4-44)
4. Check the belt tension. 4-43
5. Adjust belt tension as necessary until correct.
4-12
Rubber Track Loader
4. Maintenance
Fan Belt Removal & Installation Pry-bar

To remove the fan belt:
1. Follow steps 1 and 2 of the belt adjustment proce
dure.
2. Once loose, pivot the alternator towards the
engine to increase slack.
3. Then, remove the three bolts securing the fan Bolt
cage (half) to the fan shroud. Remove that portion
of the cage. (fig. 4-45, 4-46)
4. Slip the belt off of the engine pulleys and work it 4-44
around the fan until it is clear of the blades.
To install the fan belt:
1. Reverse the steps of the removal procedure.
2. Perform the belt tension check and adjustment 1/2 cage
procedures on page 4-12 to complete the
installation.
A/C Belt Removal & Installation

To remove the A/C belt:
1. Follow steps 1 and 2 of the belt adjustment proce Bolts
dure.
4-45
2. Once loose, pivot the A/C pump towards the
engine to increase slack.
3. Slip the belt off of the pulleys and remove
it from the machine.
To install the A/C belt:
1. Reverse the steps of the removal procedure to
reinstall the belt.
2. Perform the belt tension check and adjustment
procedures on page 4-12 to complete the
installation.
4-46 Bolt
4-13
Rubber Track Loader
4. Maintenance
Engine Oil/Filter Change

Regular oil changes are necessary to maintain a
strong running engine. ASV recommends a normal oil
change interval of 250 hours or every six months. This
recommendation has been made to help ensure proper
lubrication during operation and to prolong engine life
under typical operating conditions.
To change the oil and filter:
1. Start and run the engine for a few minutes to warm
the oil. Then turn the engine off before proceeding. 4-47
2. Place a suitable container under the engine oil
drain plug to catch the used oil as it drains.
3. Remove the belly pan beneath the engine.
(fig. 4-47)
4. Then remove the drain plug from the oil pan and
allow the used oil to drain completely from the
engine. Make sure to use the correct size combi
nation/socket wrench to keep the drain plug in
reusable condition. (fig. 4-48)
5. Remove the engine oil filter by hand or with strap if
necessary. (fig. 4-49)
4-48
6. Once the filter has been removed, check to make
sure the rubber gasket has come off of the filter
head with the old filter. If it is not on the old filter,
check the filter head. If it is still on the filter head,
remove it prior to installing the new filter.
(fig. 4-50)
NOTICE
If the old filter gasket (A) is not removed from the
filter head and the new filter is installed on top of
it, an oil leak will result when the engine is started.
If unnoticed, the engine can run itself out of oil 4-49
causing engine failure.
7. Prepare new filter for installation by rubbing fresh A

oil on the exposed surface of the filter gasket.
8. Thread the new filter onto the filter head. Tighten
the filter by hand as instructed by the label located
on the filter or filter box.
9. Re-install the oil drain plug into the pan and tighten
to 50 +/- 10 lb ft.
4-50
4-14
Rubber Track Loader
4. Maintenance
4-51
10. Remove the oil filler cap and fill the engine
crankcase with ASV 10W-30 Heavy Duty Engine
Low
Oil (capacity: 9 U.S. quarts including filter). (fig. 4-
51)
11. Install the oil filler cap. Full
12. Perform a visual inspection to make sure the drain
plug, filter and oil filler cap are in place and tight.
13. Start the engine and watch the oil pressure gauge 4-52 4-53
located in the lap bar instrument display. The nee-
dle should rise up into the green range as soon as
oil pressure has been established. If the needle Oil Level Check
doesn’t rise above the red zone shortly after start- To check the oil level:
up, turn the engine off immediately and look for 1. Park the machine on level ground.
potential problems. If the needle does move into 2. Open the hood to gain access to the engine com-
the green zone as expected, oil pressure has been partment.
achieved.
3. Locate and remove the engine oil dipstick from
14. Once the engine is running, perform a visual its tube. (fig. 4-52)
inspection to make sure there are no leaks or other
4. Wipe the dipstick with a clean shop cloth and re-
visible problems.
insert it into the tube until it comes to rest in its
15. If everything looks like it should, shut the engine seated position.
down and exit the machine.
5. Remove the dipstick once again and inspect the
16. Re-install the belly pan. end for oil on the level indicator. (fig. 4-53)
17. Perform the oil level check procedure. 6. Oil should be present on the dipstick up to, but
not over the upper (full) level indicator notch. If
Engine Oil Specifications the level is correct, reinstall the dipstick and
then close and latch the hood to complete the
ASV recommends using ASV 10W-30 Heavy Duty
procedure.
Engine Oil for most conditions. In the event of an alter-
nate working environment, the following chart may be 7. If the level is low, add the proper grade and viscos
used as a guide to oil viscosity grades. ity engine oil and re-check as necessary until the
proper level has been achieved. Then re-install the
You may also use a quality engine oil substitute meet- dipstick and filler cap and close and latch the hood
ing the following minimum specification: to complete the procedure.
• API CH-4 multigrade engine oil.
4-15
Rubber Track Loader
4. Maintenance
Hydraulic Fluid/Filter Change

Hydrostatic components require extremely clean oil in
order to have a long service life. Use extreme caution
when changing the hydraulic oil. Introducing dirt or
debris could be detrimental to the hydraulic system.
ASV recommends service intervals of 500 hours for
hydraulic fluid and 250 hours for hydraulic fluid filters.
To change the hydraulic fluid:
1. Locate the hydraulic system drain access situated
in the belly pan between the axles on the right side 4-54 4-55
of the machine. (fig. 4-54)
2. Remove the drain plug using the correct size allen
type wrench or allen socket to avoid damaging the
drain plug. (fig. 4-54, 4-55)
3. Drain the hydraulic fluid into a suitable catch con
tainer.
4. Locate the two hydraulic filters underneath the cab
on the left side of the machine. (fig. 4-56)
5. Thoroughly clean around the filters to prevent dirt
or debris from entering the system and remove the
filters by hand or with a strap as required.
4-56
6. Check to make sure the filter gaskets are still pres
ent on the old filters. If not, check the filter heads
to make sure they are free from old gasket materi
al prior to installing the new filters.
7. Prepare the new filters by rubbing a small amount
of fresh hydraulic oil onto the filter gasket surface
and then threading them onto their respective filter
heads. Tighten filters by hand as instructed by the
label located on the filter or filter box.
8. Install the hydraulic system drain plug and tighten.
9. Remove the hydraulic reservoir filler cap (black)
and fill the hydraulic system with ASV Premium All 4-57
Season MV Hydraulic Oil or equivalent until the full
mark on the hydraulic fluid sight gauge has been
reached (approx. 12.5 gal.). (fig. 4-57,4-58)
Note: When checking or adding to the hydraulic fluid
level, do so with the lift arms in the lowered position. If
the level is checked with the lift arms in the raised
position, an inaccurate reading will result.
Full
Note: When adding hydraulic fluid, add fluid slowly
until it is visible in the sight gauge. Once visible, add
fluid in one quart increments until the full mark has
been reached.
10. Install and secure the hydraulic reservoir filler cap. Low
4-58
11. Start the machine and operate all hydraulic circuits
to work any trapped air out of the system.
12. Once you have purged the air from the system,
• Drive the machine forward and backward. check the level on the hydraulic fluid level sight
• Raise and lower the lift arms(unloaded). gauge. If the level is low repeat step 9 and 10 to
• Dump and curl bucket/quick attach. complete the procedure.
4-16
Rubber Track Loader
4. Maintenance
Radiator/Oil Cooler
The Radiator and Oil Cooler must be kept clean to
ensure proper operation. Engine and hydraulic system
overheating, damage and even failure can result if the
radiator/oil cooler is not kept clean. A pressure washer
or compressed air nozzle work well to blow debris
clear of the fins in the oil cooler and radiator.
Note: If hydraulic oil or engine coolant temperature

gauges indicate abnormally high temperatures during
operation, increase cleaning intervals. 4-59
Note: In brush cutting applications check and clean

the coolers often to avoid overheating.
To clean radiator/oil cooler:
1. Make sure the engine is off, and cool.
2. Using compressed air or a pressure washer, thor-

oughly clean radiator/oil cooler as shown.
Note: Make sure water nozzle is at least 12” (8” for air)
from the cooler and that the spray is directed straight
through the cooler or the cooling fins may be damaged
(bent over) which will decrease cooling performance. 4-60
Engine
Periodic cleaning of the chassis area beneath the cab
and engine compartment are also necessary to main-
tain safe operation. Clean as required.
1. Remove the belly pans on the underside of the
machine.
2. Tilt the cab up and raise the hood at the rear of the
machine.
3. Pressure wash any debris from the engine com
partment and chassis area out through the lower
opening. 4-61
4-17
Rubber Track Loader
4. Maintenance
4-62 4-63
Case Drain Filter Fuse Panel

The PT machines are also equipped with a filter in the The electrical systems in the PT machines are
auxiliary circuit case drain line. It protects the main equipped with fuses that protect the electrical compo-
hydraulic system in the event of catastrophic failure in nents from damage. They are located on the fuse
an attachment. This filter is designed to last the life of panel behind the access cover on the lower right side
the vehicle. The only instance where this filter should of the cab interior. (fig. 4-63)
be replaced is if an attachment equipped with a case
drain has a drive motor failure during use. (fig. 4-62) In the event of an electrical malfunction, the most logi-
cal place to start is at the fuse panel. Check the fuse
related to the problem you are having and inspect it. If
the fuse appears black and burned, it needs to be
replaced. Replace fuses with the correct amperage
replacement fuse only. Replacing a fuse with one of a
lower amperage rating may lead to premature fuse fail-
ure. Replacing a fuse with one of a higher amperage
rating may burn out the electrical component the fuse
was meant to protect. See the troubleshooting section
in this manual for an additional resource to aid in track-
ing suspected electrical problems.
4-18
Rubber Track Loader
4. Maintenance
Maintenance Service Service

Interval Notes
Item required Capacity
Grease fittings Lubricate Daily Grease often.
Adjust levels as
Fluid levels Check Daily
necessary.
Fan-A/C belt Adjust tension as
Check Daily
tension necessary.
Fan-A/C belt Replace as a pair if
Inspect Daily
condition worn or damaged.
Water separator Drain Daily
Replace if severely
Track condition Inspect Daily
damaged.
Adjust tension as
Track tension Inspect Daily
necessary.
Replace if damaged or
Air cleaners Inspect Daily
heavily soiled.
Radiator/oil Clean often
Inspect Daily
cooler (as necessary).
Clean often
Undercarriages Inspect Daily
(as necessary).
Engine Clean often
Inspect Daily
compartment (as necessary).
Drive sprocket Replace if damaged or
Inspect 50 hr.
rollers worn. (35% min.)
Engine oil and 250 hr. or
Replace 9 qt.
filter 6 Mo.
Hydraulic filter Replace 250 hr.
Service refill capacity

Hydraulic oil Replace 500 hr. 12.25 gal.
only. (Dry: 21 gallons)
Water separator- Replace fuel filter
Replace 500 hr.
fuel filter element.
Coolant with SCA
Radiator coolant Replace 3000 hr. 3.125 gal
additive required.
4-19
4-20
5. Machine Controls and
Instrumentation
Chapter Overview Instrumentation

This chapter contains an overview of the machine con- The Instruments (Figure 5-2) are positioned in the lap
trols and instrumentation. For further information bar for good visibility and when seated inside the oper-
regarding machine controls, instrumentation or opera- ator enclosure. Instruments include the following com-
tion, refer to the operation and maintenance manual ponents.
for the PT-70/80. Included here are illustrations of the
following controls and instrumentation components and (1) Engine Temperature Gauge
a description of their functions. (2) Multi-Gauge
• Oil Pressure Gauge
• Machine Controls • Hyd. Oil Temperature Gauge
• Guage Location and Function • Fuel Gauge
• Switch Location and Function • Voltmeter
(3) Tachometer
Machine Controls (fig. 5-1) (4) Indicator Light Display
There are three primary machine controls: lift arm con- • High Range Indicator
trol (1), drive control (2) and throttle (3). • Low Range Indicator
• Glow Plug Operation Indicator
• Parking Brake Indicator
Lift Arm Control
The lift arm control (1) is a pilot operated joystick that
2 3
allows the operator to raise or lower the lift arms and
1 4
dump or curl the quick attach mechanism.
Drive Control
The drive control (2) is also a pilot operated joystick. It
allows the operator to change the direction and speed
of the machine. 5-2
Throttle NOTICE
The foot throttle (3) controls engine rpm. If the engine coolant temperature, engine oil pressure or
hydraulic oil temperature gauges read above normal (or
below normal for engine oil pressure) during normal machine
operation, shut the machine down immediately. Diagnose the
3
problem and make any necessaryrepairs before continuing to
operate the machine.
2 1
NOTICE
If the battery low-voltage light illuminates, drive the machine
to a suitable location and shut the engine off. Diagnose the
problem and make needed repairs before continuing to oper-
ate.
The glow plug operation light illuminates only when the

5-1 key switch is turned to engine pre-heat, showing nor-
mal operation.
5-1
Rubber Track Loader
5. Machine Controls and Instrumentation
Switches
The various switches (Figure 5-3, 5-4, 5-5) are posi-
tioned to provide good access and visibility. The stan-
dard and optional switches are listed below.
9
6
7 10
8 11
5-3 5-4
(1) Ignition
(2) Hour Meter
(3) Beacon (optional) 5
(4) Wiper (optional)

(5) Heater Fan
(optional) 4
(6) Parking Brake

(7) Headlight
(8) Bucket Pos. 3
(9) Hight Flow Aux.
(10) Low Flow Aux.
(11) Hyd. Q/A 2
1
5-5
5-2
6. Operator Enclosure
Chapter Overview Removal and Installation

This chapter provides information on the assembly and Removal and installation procedures are provided for
disassembly of the operator enclosure assembly. If the following operator enclosure components.
there is an issue that requires troubleshooting, refer to
Chapter 18, Troubleshooting. • Cab Door Gas Spring (MP-1 & MP-2)
• Forward Pillar Switch Panels MP-1 & MP-2)
• Gauge Clusters (MP-2)
Personal Safety • Side Panels/Gauges (MP-1)
!WARNING! • Seat (MP-1 & MP-2)
• Interior panels (side, MP-2) (rear, MP-1 & MP-2)
• Lap Bar Gas Assist Spring (MP-2 only)
machine damage, injury or even death.
Note: Procedures are provided for only the operator enclo-
sure components listed above. However, exploded parts dia-
grams exist in the PT-70 or PT-80 Parts manuals to serve as
visual aids in the removal or installation of other operator
fully understood the information in this manual.
enclosure components.
Refer to the Operation and Maintenance manual for
instructions regarding proper machine operation tech- Required Tools
niques before operating any Rubber Track Loader. Blade Type Screwdriver
Prior to performing any type of service work on a Door Gas Spring (MP-1 & MP-2)
Removal
Machine Preparation Retaining Clip

!WARNING!
death to personnel working on a Rubber Track Loader.
As a precaution, disconnect the battery cables from the 6-1

battery terminals, tape the battery clamps and remove
the key from the ignition switch prior to performing any
service work on a Rubber Track Loader. 1. Pry the retaining clip holding the forward end of
the gas spring to the ball stud outward. (fig. 6-1)
Place a “Do Not Operate” tag prominently on the ma-
chine to inform personnel that the machine is being
worked on.
6-2
2. Pry the gas spring off of the ball stud. (fig. 6-2)
3. Repeat this procedure on the rear of the gas

spring to remove the spring completely.
Installation
1. To reinstall, reverse the removal procedure.
6-1
Rubber Track Loader
Pillar Switch Panels (MP-1 & MP-2)

Removal (RT or LT panel)
Required Tools
Open or Box end Wrenches
6-6
6-3
1. Remove the 3 screws/bolts securing the pillar

switch panel to the cab enclosure. (fig. 6-3)
6-7
4. Pivot the panel further backward to expose the

connectors on the lower switches and disconnect
them. You may then remove the panel.
(fig. 6-6, 6-7)
Note: The connectors on the harness are labeled as

6-4 are the switches in the panel. Use these labels to
properly identify (match up) and reconnect the harness
to the switches during installation.
2. Remove the forward end of the gas spring from
Note: At this point in the disassembly process, the
the ball stud by following steps 1-2 in the Cab
activation switches in the panel may be removed and
Door Gas Spring removal procedure on page 6-1.
replaced if necessary. (fig. 6-8)
Then remove the ball stud. (fig. 6-4)
6-5
6-8
3. Once the ball stud has been removed, begin

removing the panel by pulling back on the top to
Installation (RT or LT panel)
expose the wires connected to the dome light acti- 1. To reinstall either panel, reverse the steps of the
vation switch. Carefully disconnect them from the removal procedure.
switch. (fig. 6-5)
6-2
Rubber Track Loader
Gauge Clusters (MP-2)

Removal
Required Tools
Phillips Type Screwdriver
Combination/Socket Wrench
6-12
3. If gauges must be removed, remove the nuts

securing the backing plate to the gauge. (fig. 6-12)
6-9
6-13
6-10
1. Remove the mounting screws securing the gauge

mounting plate to the lap bar gauge pod, then
raise the plate to expose the wire harness connec-
tors. (fig. 6-9, 6-10)
6-14
4. The gauge may now be removed for repair or

replacement. (fig. 6-13, 6-14)
Installation
1. To reinstall the gauges and cluster, reverse the
removal procedure.
6-11
2. Disconnect the gauges from the harness and

remove the gauge cluster. (fig. 6-11)
Note: At this point in the disassembly procedure, the

gauges may be replaced if necessary.
6-3
Rubber Track Loader
Side Panels/Gauges (MP-1)

Removal
Required Tools
Combination/Socket Wrenches
6-18
4. Remove the screws securing the rear side panel

section to the cab enclosure. (fig. 6-18)
6-15
1. Remove the screws securing the forward side

panel to the operator enclosure. (fig. 6-15)
6-19
5. Disconnect any switches from the harness (unbolt

the heater control if removing left side) then
remove the panel from the machine (fig. 6-19)
6-16
2. Pull the side panel away from the cab as shown,

disconnect the gauges/switches from the wire har-
ness, then remove it from the machine. (fig. 6-16)
6-20
6. If gauges need to be removed, remove the nuts

securing the bracket to the back of the gauge,
then remove the bracket and gauge from the
opposite sides of the panel. (fig. 6-20)
Side Panels/Gauges (MP-1)

6-17
Installation
1. To install the side panels or gauges, reverse the
removal procedure.
3. Remove the arm rests by first loosening the retain-
ing bolts from the outside of the cab, then slide the
rests up and out from the inside. (fig. 6-17)
6-4
Rubber Track Loader
Seat (MP-1 & MP-2)

Removal
Required Tools
6-24
5. Disconnect the harness and then remove the seat

from the machine. (fig. 6-24)
6-21
Seat
1. Remove the bolts (2) securing the cab to the chas- Installation
sis. They are located inside the cab in the upper 1. To install the seat, reverse the removal procedure.
front corners of the foot well. (fig. 6-21)
Interior Side Panel, LT (MP-2)
2. Raise and secure the cab as described on page 4-
2 of this manual.
Removal
Required Tools
6-22
3. Remove the four nuts securing the seat to the cab.

6-25
1. Remove the mounting screws (5) and washers

securing the panel to the chassis. (fig. 6-25)
6-23
4. Remove the seat partially to expose the seat

switch harness located behind the seat. (fig. 6-23)
6-26
2. Remove the cup holder mounting screws (4) and

remove the cup holder from the panel. (fig. 6-26)
6-5
Rubber Track Loader
6-29
2. Remove the mounting screws (6) and washers

6-27 securing the panel to the chassis. (fig. 6-29)
3. Remove the panel by lifting and twisting it over the

joystick and clear of the lap bar. (fig. 6-27)
Installation
1. To reinstall the left interior side panel, reverse the
removal procedure.
Interior Side Panel, RT (MP-2) 6-30

Removal
Required Tools
3. Disconnect the ignition switch, hour meter, and any
Phillips Type Screwdriver other switches from the cab harness. (fig. 6-30)
6-28
6-31
1. Remove the fuse panel access cover. (fig. 6-28)
4. Remove the panel by lifting and twisting it over the
joystick and clear of the lap bar. (fig. 6-31)
Installation
1. To re-install the right interior side panel, reverse
the removal procedure.
6-6
Rubber Track Loader
Rear Interior Panel (MP-1 & 2) Lap Bar Gas Spring (MP-2)
Removal Removal
Required Tools Required Tools
Phillips Type Screwdriver Phillips & Blade Type Screwdrivers
1. Remove the right, left and rear interior panels from

the cab to access the gas spring.
6-32
1. Remove the screws holding the rear panel to the

cab. (fig. 6-32)
6-34
2. Put the lap bar in the raised position to relieve ten-

sion on the lap bar gas spring. (fig. 6-34)
6-33
2. Disconnect the rear power point from the harness,

then remove the panel from the cab. (fig. 6-33)
Installation
1. To re-install the rear interior panel, reverse the
removal procedure. 6-35
3. Using a small screwdriver, remove the retaining

clip from each end of the gas spring. (fig. 6-35)
4. Remove the gas spring by pulling both ends off of

the ball joints.
Installation
1. Reverse the removal procedure to reinstall the lap
bar gas spring.
6-7
6-8
7. Chassis and Fuel Tank

This chapter provides information on the assembly and Removal and installation procedures are provided for
disassembly of the chassis. If there is an issue that the following chassis components.
requires troubleshooting, refer to Chapter 18,
Troubleshooting. • Fuel Sending Unit
• Fuel Tank
• Footwell
Personal Safety • Foot Throttle Assembly
• Hood Assembly
!WARNING!
Improper or incomplete maintenance/repair of a Rubber Note: Procedures are provided for only those chassis com-
Track Loader can be dangerous and may result in ponents listed above. However, exploded parts diagrams
machine damage, injury or even death. exist in the PT-70 or PT-80 Parts manual to serve as visual
aids in the assembly and disassembly of other chassis com-
Do not attempt to perform any type of repair or mainte- ponents.
fully understood the information in this manual. Required Tools
Screwdriver
Refer to the Operation and Maintenance manual for Combination/Socket Wrench
niques before operating any Rubber Track Loader.
Fuel Sending Unit
Prior to performing any type of service work on a Removal
Rubber Track Loader, read and understand Chapter 1 1. Raise and support the lift arms as described on
(Product Safety) for personal safety information. page 4-1 of this manual.
2. Tilt and support the operator enclosure (cab) as

Machine Preparation described on page 4-2 of this manual. (optional)
!WARNING!
As a precaution, disconnect the battery cables from the

Fuel Sending Unit

worked on.
7-1
3. Locate the fuel sending unit on the left side of the

machine in the upper front corner of the fuel tank.
(fig. 7-1)
4. Remove the nuts and associated hardware secur-

ing the leads to the sending unit. (fig. 7-1)
Note: Record the order of assembly and polarity of the

leads to ensure proper function when reassembled.
7-1
Rubber Track Loader
Fuel Tank
Remove Screws Removal
Required Tools
Screwdriver
1. Raise and support the lift arms as described on
page 4-1 of this manual.

described on page 4-2 of this manual. (optional)
7-2
5. Remove the screws securing the fuel sending unit

to the tank. (fig. 7-2)
7-5
3. Loosen the hose clamps securing the vent hoses

to the left rear tank end. (fig. 7-5)
7-3
6. Remove the sending unit by pulling it through the

opening in the fuel tank. (fig. 7-3)
Installation 7-6
1. To install the fuel sending unit, reverse the removal
procedure. (See fig. 7-4 for terminal installation)
4. Disconnect and plug the hoses. (fig. 7-6)
-- Neg
Install First
+ Pos
Install Last 7-7

7-4
5. Remove the bolts securing the forward belly pan

and remove it from the machine. (fig. 7-7)
7-2
Rubber Track Loader
7-8 7-11
6. Loosen the hose clamp securing the main fuel line 9. Remove the bolts (3) securing the fuel tank to the
to the tank outlet in the front right corner of the front mounting plate. (fig. 7-11)
machine. (fig. 7-8)
7-12
7-9
10. Now that the tank is loose and empty, loosen the
7. Disconnect this line and drain the fuel into a suit- hose clamp and disconnect the filler tube from the
able catch container. (fig. 7-9) right rear end of the tank. (fig. 7-12)
Note: Collect and contain flammable liquids in suitable

containers. Dispose of all liquids in accordance with
local regulations and mandates.
out
7-13 up
11. Lift and remove the tank from the machine.

(fig. 7-13)
7-10
Installation
8. Remove the bolts securing the fuel tank to the 1. To install the fuel tank, reverse the removal proce-
fenders. (fig. 7-10) dure.
7-3
Rubber Track Loader
7. Chassis & Fuel Tank
Footwell
Removal Bolts
Required Tools
Screwdriver
1. Raise and support the lift arms as described on
page 4-1 of this manual. (optional)

described on page 4-2 of this manual. 7-16
5. Remove the bolts (4) securing the footwell assem-

bly to the chassis. (fig. 7-16)
7-14
3. Remove the bolts (4) securing the foot pedal cover

to the pedal, then remove the cover. (fig. 7-14)
Ball Stud
7-17
Pry Off
6. Remove the footwell from the chassis as shown.
(fig. 7-17)
Installation
Throttle Cable 1. To install the footwell, reverse the removal proce-
7-15 dure.
4. Pry the throttle cable off of the ball stud on the foot
pedal. (fig. 7-15)
7-4
Rubber Track Loader
Foot Throttle Assembly Hood Assembly

Removal Removal
Screwdriver Screwdriver
Combination/Socket Wrench Combination/Socket Wrench
Note: The foot throttle assembly may be removed with
the footwell still installed in the machine.
1. Perform steps 3 and 4 of the footwell removal pro-

cedure on page 7-4.
Bolts
7-19
Pry Off
7-18
2. Remove the bolts (2) and associated hardware

securing the foot throttle assembly to the footwell. 7-20
(fig. 7-18)
Note: Record the order of assembly during removal to 1. Remove the bolts (4) securing the fluid filler tray
ensure proper operation when re-installed. and hoses to the hood assembly. (fig. 7-19, 7-20)
3. Remove the foot throttle from the machine.
Installation
1. To install the foot throttle assembly, reverse the
removal procedure.
7-21
7-22
2. Remove the bolts (6) that secure the hood to the

chassis. (fig 7-21, 7-22)
7-5
Rubber Track Loader
7-23
3. Have an assistant help you to remove the hood

assembly from the machine. (fig. 7-23)
7-24
4. Carefully set the hood assembly aside. (fig. 7-24)
Installation
1. To install the hood assembly, reverse the removal
procedure.
7-6
8. Radiator and Oil Cooler

This chapter provides information on the disassembly Removal and installation procedures are provided for
and assembly of the radiator/oil cooler and associated the following radiator/oil cooler components.
components. If there is an issue that requires trou-
bleshooting, refer to chapter 18, Troubleshooting. • Fan Guard
• Fan
Personal Safety • Fan Shroud
• Radiator/Oil Cooler
!WARNING!
Improper or incomplete maintenance/repair of a Rubber Note: Procedures are provided for only those radiator/oil
Track Loader can be dangerous and may result in cooler components listed above. However, exploded parts
machine damage, injury or even death. diagrams exist in the PT-70 and PT-80 Parts manuals to
serve as visual aids in the assembly and disassembly of
Do not attempt to perform any type of repair or mainte- other system components.
fully understood the information in this manual. Note: Refer to pages 3-1and 3-2 for pictorial views of the fil-
tering and cooling system components.
niques before operating any Rubber Track Loader. Fan Guard
Removal
Machine Preparation Required Tools
!WARNING! Combination Wrench
Accidental machine starting can cause injury or even Socket Wrench
death to personnel working on a Rubber Track Loader. Socket Wrench Extension (optional)


worked on.
Prior to performing any type of service work on a

(Product Safety) for personal safety information. 8-1
1. Remove the air cleaner end cap and elements to

provide clearance for guard removal. (fig. 1)
8-1
Rubber Track Loader
Fan & Fan Shroud

Removal
Required Tools
Combination Wrench
Socket Wrench
8-2
8-5
1. Remove the bolts (2) securing the fuel pump/filter

assembly to the radiator support and lay it aside
over the bumper to allow clearance to remove the
shroud and fan. (fig. 8-5)
8-3
2. Remove bolts (5) securing the fan guard halves to

the fan shroud. (fig. 8-2, 8-3)
8-6
2. Remove the bolts (6) securing the radiator and

8-4 shroud to the radiator support. (fig. 8-6)
3. Remove both halves of the guard from the

machine. (LT side shown, fig. 8-4)
Installation
1. To install the fan guard halves, reverse the
removal procedure.
8-7
3. Push the shroud forward to allow access the fan

mounting bolts. (fig. 8-7)
8-2
Rubber Track Loader
Radiator/Oil Cooler
Removal
!WARNING!
Personal injury can result from exposure to hot fluids
and components. Allow the machine to cool thoroughly
before attempting any type of service on the cooling or
hydraulic systems.
!WARNING!
8-8
Cooling system conditioner contains alkali. Avoid con-
tact with skin and eyes.
NOTICE
Collect and contain liquids in suitable containers. Dispose of
all liquids according to local regulations and mandates.
Required Tools
Socket Wrench
Pliers
Screwdriver
Hydraulic Caps/Plugs (various sizes)
8-9
1. Perform the fan guard and fan/shroud removal pro-
cedures.
4. Remove the bolts securing the fan and spacer to
the engine, then remove the fan and spacer from
between the shroud and radiator as shown.
(fig. 8-8, 8-9)
8-11
2. Remove the bolts securing the rear belly plates to

the chassis and remove them. (fig. 8-11)
Catch Container
8-10 Drain Valve
5. Remove the radiator shroud from the machine.

(fig. 8-10)
Installation 8-12
1. To install the fan and fan shroud, reverse the
removal procedure. 3. Attach a piece of 3/8” fuel line to the drain valve,
outlet, then twist the valve control counter clock-
wise to drain the cooling system. (fig. 8-12)
8-3
Rubber Track Loader
8-16
8-13
4. Remove the bolts (6) securing the outer shroud to

the chassis, then remove the shroud. (fig. 8-13)
8-17
7. Loosen the clamps securing the upper and lower

coolant hoses to the radiator, then disconnect the
8-14 hoses from the radiator. (fig. 8-16, 8-17)
5. Remove the upper hydraulic cooler hose. Cap or

plug the hose upon removal. (fig. 8-14)
8-18
8. Tilt the radiator rearward and then remove it from

8-15 the machine. (fig. 8-18)
Installation
6. Loosen and disconnect the lower hydraulic line 1. To install the radiator/oil cooler, reverse the
from the cooler. Cap and plug the line and cooler removal procedure.
opening upon disassembly. (fig. 8-15)
8-4
9. Hydraulic Reservoir

This chapter provides removal and installation proce- Removal and installation procedures are provided for
dures for the hydraulic reservoir. the following hydraulic components.
Personal Safety • Hydraulic Reservoir (tank)

• Suction Screen
!WARNING!
Improper or incomplete maintenance/repair of a Rubber Note: Procedures are provided for only those hydraulic com-
Track Loader can be dangerous and may result in ponents listed above. However, exploded parts diagrams
machine damage, injury or even death. exist in the PT-70 and PT-80 Parts manuals to serve as visu-
al aids in the removal and installation of other system com-
Do not attempt to perform any type of repair or mainte- ponents.
fully understood the information in this manual. Note: Refer to pages 3-1, 3-2 and 3-3 for additional
hydraulic circuit and system information.
Hydraulic Reservoir
Removal (in event of contamination)
Machine Preparation Required Tools
!WARNING! Screwdriver
Accidental machine starting can cause injury or even Combination/Socket Wrench
death to personnel working on a Rubber Track Loader. Pry Bar(s)

battery terminals, tape the battery clamps and remove !WARNING!
service work on a Rubber Track Loader. Remove any attachment, relax all actuators and make
sure the hydraulic oil is cool before removing any com-
Place a “Do Not Operate” tag prominently on the ma- ponents or lines. Hot or pressurized oil can cause per-
chine to inform personnel that the machine is being sonal injury.
worked on.
NOTICE
Prior to performing any type of service work on a Collect and contain liquids in suitable containers. Dispose of
NOTICE
During disassembly, plug and cap all hoses and fittings to
prevent system fluid loss or contamination.
9-1
Rubber Track Loader
1. Remove the center and rear belly pans from the

machine.
2. Drain the hydraulic fluid. Refer to page 4-16 for the

hydraulic fluid and filter change procedure.
3. Remove the engine as described on page 12-5 of

this manual.
4. Remove the auxiliary and drive pumps (for inspec- Disconnect

tion, repair, or replacement) according to the pro-
cedures in section 11 of this manual.
9-4
6. Remove the clamps securing the quick attach hard

lines and the test port line that run from the pilot
generation block down the left side of the machine
to the engine compartment. (fig. 9-4)
9-1
9-5
7. Disconnect the quick attach hoses from the hard

lines (if equipped). (fig. 9-5)
9-2
Disconnect
9-6
8. Disconnect the quick attach and test port lines

9-3 from the pilot generation block. (fig. 9-6)
5. Disconnect the hoses and lines attached to the two

upright portions of the tank. (fig. 9-1, 9-2, 9-3)
9-2
Rubber Track Loader
9-7 9-10
9. Gently move the hard lines out of the way to allow

for reservoir removal then zip tie them to the motor
mount to keep them secure. (fig. 9-7)
9-8 9-11
10. Disconnect the bucket cylinder hoses from the 12. Disconnect the bucket cylinder hard lines from the
hard lines in the upper right portion of the engine lift arm control valve and then remove them from
compartment. Remove all line clamps. (fig. 9-8) the machine. (fig. 9-10, 9-11)
Retainer
9-9 9-12
11. Disconnect the lift cylinder hoses from the hard 13. Remove the hose retainer or move it aside as
lines to allow the bucket cylinder lines to be shown. (fig. 9-12)
removed. (fig. 9-9)
9-3
Rubber Track Loader
9-13 9-16
14. Disconnect the main oil cooler line from the fitting 16. Remove the clamps securing the auxiliary
at the filter. (fig. 9-13) hydraulic lines to the chassis. (fig. 9-16)
Disconnect
9-17
9-14
9-18
9-15 17. Disconnect the auxiliary hydraulic lines from the lift
arm control valve and the hoses leading to the
quick coupler lines on the lift arm. (fig. 9-17, 9-18)
15. Disconnect the main oil cooler line from the junc-
tion block, then remove it from the machine.
(fig. 9-14, 9-15)
9-4
Rubber Track Loader
9-19
9-22
fuel lines 20. Remove the auxiliary hydraulic tubes from the
machine.
9-20
18. Slide the two fuel lines through the chassis open-
ing and into the engine compartment so that the 9-23
aux. hyd. tubes can be removed. (fig. 9-19, 9-20)
21. Disconnect the lower portions of the cab support

gas springs from the chassis. (fig. 9-23)
9-21
19. Disconnect the fuel sender from the main harness 9-24
at the connector.
Note: If there is anything else that is routed behind the 22. Label, then disconnect any control hoses coming
auxiliary hydraulic tubes that will prevent them from from the joysticks that are still attached to compo-
being removed, disconnect or carefully remove these nents to allow them to be pulled up through the
items at this time to allow the tubes to be removed. chassis opening for clearance. (fig. 9-24)
Note: Refer to the individual hydraulic component

removal and installation procedures if additional infor-
mation is needed to properly connect hoses during
reassembly.
9-5
Rubber Track Loader
9-25 9-28
23. Remove the lower hose restraints to allow the 26. Remove the bolts securing the metal tank restraint
hoses to be pulled through the chassis. (fig. 9-25) straps, them remove them from the machine.
(fig. 9-28)
9-26
9-29
24. Pull the hoses up through the chassis opening and
lay them aside as shown (both sides). (fig. 9-26) 27. Slide the quick attach and test port tubes forward
so that they do not interfere with the reservoir
(tank) moving upwards in the chassis. (fig. 9-29)
9-27
9-30
25. Disconnect the wiring running through the hose
passageway and pull it through the opening as
shown. (fig. 9-27) 28. Slide the various control hoses to the side of the
reservoir (tank) so that they do not interfere with
the tank moving upwards in the chassis. (fig. 9-30)
9-6
Rubber Track Loader
29. Make sure there is nothing that would visibly pre-

vent the reservoir from being removed or is still
attached to other components within the machine,
then proceed.
Reservoir
Pry-bar
9-31 9-34
30. Use a long pry bar to pry the tank upward and 31. Once the tank is over the axle mounts lift and
rearward from the front as shown. (fig. 9-31) remove it from the chassis as shown. (fig. 9-32, 9-
33, 9-34)
Note: You may need to pry the tank upwards within
the chassis from the rear if it isn’t already to prepare
the tank to be moved in step 30. Installation
1. To install the hydraulic reservoir, reverse the
removal procedure.
Note: The only service issue warranting the removal of

the reservoir is hydraulic system contamination. Upon
installation, the tank must be clean and free of any dirt
or debris that may contaminate the hydraulic oil. If you
are unable to successfully flush the tank clean of all
dirt or debris, replace the tank.
9-32
9-33
9-7
Rubber Track Loader
Suction Screen
Removal Suction screen
Required Tools
Small Pry Bar (hose removal if necessary)
Socket Wrench & Extension
Combination Wrenches (to remove lines)
Note: The suction screen may be removed with the
reservoir (tank) still in the machine. If this is necessary,
remove the center belly pan and tilt and support the
cab to gain access, then follow the procedure
described below to remove the suction screen.
9-37
1. If the tank is still in the machine, drain the
hydraulic fluid as described on page 4-16 of this
manual. 4. Slide the assembly out of the reservoir as shown
in fig. 9-36 and 9-37.
2. If the tank is still in the machine, remove/discon-
nect any hoses connected to the flange weldment 5. The suction screen is now accessible for inspec-
that may interfere with removal. tion or replacement.
Note: If removal is necessary, thread the suction

screen off of the flange weldment and remove.
Installation
1. To install the suction screen, reverse the removal
procedure.
Note: It is important to inspect the screen for pieces of

metal or other debris that may have been generated by
a worn or defective component. If there is debris pres-
ent on the screen, the hydraulic system (including the
reservoir) must be flushed clean to remove any and all
contamination (debris). The screen should be replaced
9-35 as well as any components found to be defective.
3. Remove the bolts securing the flange to the

hydraulic reservoir. (fig. 9-35)
o-ring
9-36
9-8
10. Lift-Arm/Drive Controls

dures for the lift-arm and drive control components. the following lift-arm/drive control components.
Personal Safety • Pilot Control Joystick

• Lift Arm Float Magnet
!WARNING! • Lift Arm Control (loader) Valve
Track Loader can be dangerous and may result in Note: Procedures are provided for only those lift-arm/drive
machine damage, injury or even death. control components listed above. However, exploded parts
diagrams exist in the PT-70 and PT-80 Parts manuals to
Do not attempt to perform any type of repair or mainte- serve as visual aids in the assembly and disassembly of
nance on a Rubber Track Loader until you have read and other system components.
Note: Refer to page 3-2 and 3-3 for pictorial views of the
Refer to the Operation and Maintenance manual for hydraulic auxiliary and drive systems and components.
Pilot Control Joystick
Machine Preparation Removal
!WARNING! Required Tools
Accidental machine starting can cause injury or even Side Cutter
death to personnel working on a Rubber Track Loader. Combination/Open End/Socket Wrenches
Hydraulic Caps/Plugs (various sizes)
the key from the ignition switch prior to performing any Note: The procedures for removing and installing the right
service work on a Rubber Track Loader. and left joysticks are basically identical. As a result, only the
procedures for the right joystick are described in this section.
chine to inform personnel that the machine is being NOTICE
worked on.
Cap and plug all fittings and hoses to prevent fluid loss
Prior to performing any type of service work on a and or contamination during service work.
(Product Safety) for personal safety information. !WARNING!
Remove any attachment, lower the lift arms and make
sure the hydraulic oil is cool before removing any com-
ponents or lines. Hot or pressurized oil can cause per-
sonal injury.
10-1
Rubber Track Loader
1. Relax all hydraulic actuators to relieve pressure in

the hydraulic system prior to service.
2. Turn the ignition switch to the OFF position,

remove the key and disconnect the battery to
avoid accidental start. Remove (optional)
3. Perform the interior side panel removal procedure

that addresses the joystick you plan to remove on
page 6-4 or 6-5 of this manual. 10-3
6. Remove the bolts (3) securing the joystick mount-

ing bracket to the cab from the outside. (fig. 10-3)
(optional)
7. Label the hydraulic hoses to aid in reassembly

(see page 3-7 or 3-8 for routing and identification).
10-1
4. Expose and cut the zip tie securing the lower por-
tion of the boot to the joystick body, then lift it
10-4
upwards. (figure 10-1)
Magnet
10-5
10-2 8. Disconnect the hydraulic hoses from the various

joystick fittings and lay them aside. (fig. 10-4,10-5)
Note: The float magnet is now exposed as well as the

mounting bolts securing the joystick to the bracket.
(figure 10-2)
5. Label each of the hoses during the removal

process to aid in reassembly.
10-6
9. Disconnect all connectors coming from the joystick

harness. (fig. 10-6)
10-2
Rubber Track Loader
Lift Arm Float Magnet

Removal
Required Tools
Fittings
Socket Wrench
Combination/Open End Wrench
Allen Wrench
1. Perform steps 3, 4 and 11 of the lift arm joystick
control removal process.
10-7
10. Remove the fittings on the back of the joystick (lift

arm control joystick only). (fig. 10-7)
10-10
2. Remove the allen bolt from the underside of the

10-8 magnet. (fig. 10-10)
3. Disconnect the magnet harness connector from

11. Remove the bolts and nuts securing the joystick to the machine.
the mounting bracket. (fig. 10-8)
10-9 10-11
4. Lift the joystick within the bracket slightly, then pull

the magnet harness and connector through the
12. Lift the joystick through the opening in the bracket bracket past the joystick to remove it. (fig. 10-11)
and remove it from the machine. (fig. 10-9)
Installation Installation
1. To install the joystick, reverse the removal proce- 1. To install the float magnet, reverse the removal
dure. procedure.
10-3
Rubber Track Loader

Removal
Required Tools
Socket Wrench
Screwdriver (hose clamps)
1. Perform the footwell removal procedure on page 7-
4 of this manual.
10-15
2. Drain the hydraulic system as described on page
4-15 of this manual.
10-16
10-12
5. Disconnect all lines and hoses from the valve to

3. Label all lines and hoses as necessary to aid in allow for removal. (figure 10-15, 10-16)
reassembly. (fig. 10-12)
10-13
10-17
6. Remove the carriage bolts (3) securing the loader

valve to the chassis, Then remove the valve.
Note: The bolts have a square shank that mates with

a square hole in the chassis to keep them from rotat-
ing upon removal.
10-14
Installation
1. To install the lift arm control valve, reverse the
4. Disconnect the hose from the barb type fitting on removal procedure.
the auxiliary pump and the large hard line that
sweeps across the front of the pumps and con-
nects to the filter head to provide additional clear-
ance for line removal. (fig. 10-13, 10-14)
10-4
11. Hydraulic Pumps/Motors

dures for the hydraulic pumps and motors. the following hydraulic components.
• Charge Pump
Personal Safety • Auxiliary Pump
• Tandem (Drive) Pump
!WARNING! • Drive Motor
Track Loader can be dangerous and may result in Note: Procedures are provided for only those hydraulic com-
machine damage, injury or even death. ponents listed above. However, exploded parts diagrams
exist in the PT-70 and PT-80 Parts manuals to serve as visu-
Do not attempt to perform any type of repair or mainte- al aids in the removal and installation of other system com-
nance on a Rubber Track Loader until you have read and ponents.
Note: Refer to pages 3-1, 3-2 and 3-3 for additional motor,
Refer to the Operation and Maintenance manual for pump and hydraulic system information.
Charge Pump
Accidental machine starting can cause injury or even Screwdriver
death to personnel working on a Rubber Track Loader. Combination Wrench
Socket Wrench
the key from the ignition switch prior to performing any !WARNING!
Remove any attachment, relax all actuators and make
Place a “Do Not Operate” tag prominently on the ma- sure the hydraulic oil is cool before removing any com-
chine to inform personnel that the machine is being ponents or lines. Hot or pressurized oil can cause per-
worked on. sonal injury.
Prior to performing any type of service work on a NOTICE

Rubber Track Loader, read and understand Chapter 1 Collect and contain liquids in suitable containers. Dispose of
NOTICE
NOTICE
During disassembly, plug and cap all hoses and fittings to
The hydraulic system fluid should be changed follow- prevent system fluid loss or contamination.
ing any hydraulic component service according
to the procedure described on page 4-16.
11-1
Rubber Track Loader
1. Lower the lift arms to the ground and relax the

bucket tilt/curl cylinders to relieve pressure within
the hydraulic system.
2. Turn the ignition switch to the OFF position and

remove the key to avoid accidental start.
3. Drain the hydraulic fluid. Refer to page 4-16 for the

hydraulic fluid and filter change procedure.
4. Raise the hood at the rear of the machine.

11-3
Upper Hose
8. Remove the charge pump from the engine. (fig.
11-3)
Installation
Gasket 1. To install the charge pump, reverse the removal
procedure.
Lower Hose Note: The front bearing on the charge pump uses
engine oil for lubrication. It must be kept extremely
clean. Make sure to shield it as well as the opening to
11-1 the engine from dirt or debris while disassembled.
The gasket that seals the pump to the engine housing

5. Disconnect the hose from the upper charge pump should be replaced whenever the charge pump is
fitting. (fig. 11-1) removed and installed to prevent oil leaks and or
dirt/debris from entering the engine during operation.
6. Loosen the hose clamp and disconnect the hose
from the barb type inlet tube on the underside of
the charge pump. (fig. 11-1)
Bolt
11-2
7. Remove the upper and lower 12 point bolts secur-

ing the charge pump to the engine. (fig. 11-2)
11-2
Rubber Track Loader
Auxiliary Pump
Removal
Required Tools
Combination Wrench
Pry bar
Allen socket
11-6
4. Loosen the clamp securing the hose onto the

barbed fitting on the right side of the pump, then
disconnect it. (fig. 11-6)
11-4
1. Loosen the bolts securing the spilt flange clamp to

the upper front port on the aux. pump. (fig. 11-4)
Weldment
2. Remove the clamp and lay the hose aside.
11-7
5. Loosen the clamps securing the hoses to the inlet

weldment attached to the bottom of the pump. (fig.
11-7)
11-5
3. Disconnect the hose connected to the relief valve

assembly and lay it aside. (fig. 11-5)
11-8
6. Loosen and remove the split flange clamp securing

the inlet weldment to the bottom of the pump simi-
larly to the one previously removed on the top of
the pump. (fig. 11-8)
11-3
Rubber Track Loader
Tandem (Drive) Pump

Removal
Required Tools
Screwdriver
Combination/Open End Wrenches
!WARNING!
Personal injury can result from exposure to hot fluids
11-9 and components. Allow the machine to cool thoroughly
before attempting any type of service on the cooling or
hydraulic systems.
7. Use a pry-bar to pry the inlet weldment out of the
hoses. (This can be difficult, lubricating the inlet NOTICE
tubes with a penetrating lubricant may make Collect and contain liquids in a suitable container. Dispose of
removal easier.) (fig. 11-9) all fluids according to local regulations and mandates.
NOTICE
During disassembly, plug and cap hoses and fittings to
prevent fluid loss and or contamination.
1. Perform the auxiliary pump removal procedure on

page 11-3 of this manual.
11-10
8. Remove the upper and lower pump mounting bolts

with an allen socket and extension. You may need
to separate the pumps slightly to remove the bolts
completely. (fig. 11-10)
11-12
2. Label and disconnect all hoses from the tandem

drive pump. (fig. 11-12, 11-13, 11-14, 11-15)
Note: You may need to remove the pump mounting

bolts and twist the pump to access and disconnect
some of the hoses connected to the drive pump.
11-11 Note: Use figures 11-13, 11-14, and 11-15 to aid in

hose removal and installation and identification.
9. Carefully remove the pump from the machine. (fig.

11-11)
Installation
1. To install the auxiliary pump, reverse the removal
procedure.
11-4
Rubber Track Loader
Top & Bottom Drive Pump Hoses

To
Oil Cooler TOP
To
(return) Drive Motor
(RT)
BTM BTM
From
Charge
BTM BTM BTM Filter
To
FRONT
Drive Motor
(LT)
LEFT RIGHT
• View is from the top. REAR

11-13 • The pump is to be perceived as transparent. 11-16
• Ports are labeled top or bottom as they are on the pump.
Top & Bottom Control Hoses 3. Support the pump with a hoist or floor jack to pre-
vent it from falling as the mounting bolts are
removed. (fig. 11-16)
E TOP
C BTM
Remove Bolts (2)
FRONT
F TOP
D BTM LEFT RIGHT
REAR
• View is from the top.

11-14 • The pump is to be perceived as transparent.
• Ports are labeled top or bottom as they are on the pump.
Side Drive Pump Hoses

11-17
4. Remove the upper and lower mounting bolts from

the drive pump. (fig. 11-17)
From To
Pilot Gen Pilot Gen
Block Block
FRONT
LEFT RIGHT
REAR
11-15 • View is from the top.
11-18
5. Remove the drive pump from the machine.
Installation
1. To install the drive pump, reverse the removal pro-
cedure.
Note: Torque the tandem pump mounting bolts to 85 lb. ft.

and use blue Loc-tite or equivalent to secure the bolts in
position.
11-5
Rubber Track Loader
Drive Motor
Removal
Required Tools
Impact Wrench
3-Jaw Puller
Snap Ring Pliers
Hammer/Mallet
1. Remove the track from the undercarriage by per-
forming the track removal procedure on page 4-6
of this manual. 11-21
4. Remove the bearing support plate from the under-

Remove Bolts carriage. (fig. 11-21)
11-19
2. Remove the three bolts securing the outer bearing 11-22

support plate to the drive table. (fig. 11-19)
5. Use a hammer to tap around the circumference of

the bearing cap which releases the outward pres-
sure holding it in place. (fig. 11-22)
11-20
3. Remove the four bolts securing the outer bearing

support plate to the bearing assembly. (fig. 11-20) 11-23
6. Remove the bearing cap from the assembly. (fig.

11-23)
11-6
Rubber Track Loader
11-24 11-27
7. Remove the snap ring securing the bearing 10. Remove the sprocket assembly from the undercar-
assembly to the outer sprocket shaft. (fig. 11-24) riage. (fig. 11-27)
11-25 11-28
8. Use a jaw style puller and an impact wrench to 11. Remove the bolts securing the drive motor to the
remove the bearing assembly from the sprocket drive table. (fig. 11-28)
shaft. (fig. 11-25)
11-29 Remove Bolts

11-26
12. Lift the drive motor straight upward until it clears

9. Remove the bolts securing the sprocket to the the drive table, then forward to expose the
drive motor. (fig. 11-26) hydraulic hoses for removal. (fig. 11-29)
Note: There are two large bolts near the front of the
drive motor support securing it to the lower drive table
from the inside (near the chassis). Remove these bolts
prior to lifting the motor to provide additional clearance
for the hoses as you lift the motor upward. (fig. 11-29)
11-7
Rubber Track Loader
11-30
13. Note the orientation of the hoses as they are con-

nected to the drive motor. Label them to ensure
correct installation and proper orientation during
reassembly. (fig. 11-30)
11-31
14. Disconnect the hoses from the drive motor making

sure to cap and plug all openings to avoid contam-
ination. Remove the drive motor from the under-
carriage. (fig. 11-31)
Installation
1. To install the drive motor into the undercarriage,
reverse the removal procedure.
Note: During the removal of the bearing cap, the

bulged or domed area is beaten inward. When rein-
stalling the cap, flip it around so that the domed area is
toward the outside of the machine. Then tap the center
of the cap with a ball peen hammer or similar device to
reset the cap. Do this gently, too much force can dam-
age (mushroom) the bearing shaft.
11-8
12. Engine

This chapter provides procedures for the removal and Removal and installation procedures are provided for
installation of the engine and associated components. the following engine related components.
• Battery
Personal Safety • Exhaust
!WARNING! • Air Cleaner
Improper or incomplete maintenance/repair of a Rubber • Engine
machine damage, injury or even death. Note: Procedures are provided for only those engine associ-
ated components listed above. However, exploded parts dia-
Do not attempt to perform any type of repair or mainte- grams exist in the PT-70 and PT-80 parts manuals to serve
nance on a Rubber Track Loader until you have read and as visual aids in the assembly and disassembly of other sys-
fully understood the information in this manual. tem components.

instructions regarding proper machine operation tech- Battery
niques before operating any Rubber Track Loader. Removal
12-1
1. Open the hood at the rear of the machine.
2. Disconnect the negative and positive battery

cables from the battery terminals. (fig. 12-1)
12-2
3. Remove the wingnuts securing the battery hold

down strap. (fig. 12-2)
12-1
Rubber Track Loader
12. Engine
Exhaust System
Removal
Required Tools
Pry Bar(s)
Rubber Mallot
Penetrating Lubricant
12-3
!WARNING!
The exhaust system is very hot at operating tem-
4. Remove the two tension (L) rods by twisting and perature. Make sure the machine is off and cool
maneuvering them out of the chassis mounting before attempting to service the exhaust system.
holes. (fig. 12-3)
1. Perform the radiator/oil cooler removal procedure
on page 8-3 to provide access to the exhaust sys-
tem components.
12-4
5. Lift and remove the battery from the battery tray. 12-6
(fig. 12-4)
2. Remove the bolts securing the rear belly pan and
remove it from the machine. (fig. 12-6)
12-7
12-5
3. Remove the nuts securing the head-pipe to the

6. If necessary, remove the battery tray by sliding it turbo, then pull it away from the studs. (fig. 12-7)
upwards and then pulling it away from the chassis.
(fig. 12-5)
Installation
1. To install the battery, reverse the removal proce-
dure.
12-2
Rubber Track Loader
12. Engine
Spring
12-8 12-11
4. Remove the tension springs that secure the middle 7. Remove the inlet pipe from the muffler. It may be
pipe section to the head (upper) pipe and muffler necessary to use levers to force the inlet pipe sec-
inlet (lower) pipe. (fig. 12-8) tion out of the muffler. (fig. 12-11)
Note: Use caution not to damage the pipe or connec-

tion point during removal.
12-9
5. Remove the upper and middle pipe sections from

the machine. (fig. 12-9) 12-12
8. Remove the tail pipes from the muffler. If neces-

sary, tap the pipes lightly with a rubber mallot or
dead blow hammer to loosen the joints. (fig. 12-12)
Note: Use caution when striking the pipes with a mal-

lot. The pipes are easily damaged and may be disfig-
ured by the blows.
12-10
6. Remove the clamps that secure the inlet and outlet

pipes to the muffler. (fig. 12-10)
Note: Thoroughly coat all clamped exhaust pipe joints

with a penetrating lubricant prior to attempting to
remove the pipe sections from the muffler. This will
make removal significantly easier. 12-13
9. Remove the four bolts (and nuts) securing the muf-

fler to the chassis, then remove the muffler. (fig,
12-13).
12-3
Rubber Track Loader
12. Engine
Air Cleaner
Removal
Required Tools
Combination Wrenches
12-14
10. You may now remove the tail pipes by sliding them
forward within the chassis, then out. (fig, 12-14).
Installation
12-15
1. To install the exhaust system, reverse the removal
procedure.
1. Remove the cover and the filter elements from the
air cleaner assembly. (fig. 12-15)
12-16
2. Loosen the clamp securing the intake hose to the

air cleaner housing. (fig. 12-16)
12-17
3. Remove the bolts and nuts securing the air cleaner

housing to the chassis. (fig. 12-17)
12-4
Rubber Track Loader
12. Engine
Engine
Removal
Required Tools
Combination/Socket Wrenches
Angle Iron or Similar (approx. 43” long)
Tie Down or Ratchet Strap
Forklift/Engine Hoist
Pry Bar
12-18
1. Perform the battery, air cleaner, and charge pump,
4. Remove the air cleaner housing from the machine. removal procedures in sections 11 and 12 of this
(fig. 12-18) manual prior to starting this procedure.
2. Remove the hood assembly as described on page

Installation
7-5 of this manual.
1. To install the air cleaner assembly, reverse the
removal procedure.
3. Raise and support the operator enclosure (cab) as
described on page 4-2 of this manual.
4. Perform steps 2-7 of the exhaust removal proce-

dure on page 12-2 of this manual.
5. Remove the center belly pan from the machine.
12-19
6. Remove the front motor mount bolts (2) from the

machine. (fig. 12-19)
12-20
7. Remove the rear motor mount bolts (2) from the

machine. (fig. 12-20)
12-5
Rubber Track Loader
12. Engine
Ballstud Bolts
Cable
12-21 12-24 Engine
8. Disconnect the throttle cable from the engine. 11. Disconnect the case drain filter and bracket from
the engine adapter plate and lay it aside. It is situ-
Note: Once loose, you may want to pull the throttle ated beneath the drive pump. (fig. 12-24)
cable forward through the chassis to make sure it is
clear of the engine during removal.
Bolts
Wire Harness
Restraint
Restraint
12-25
12-22 Rear Axle 12. Remove the two bolts securing the drive pump to
the engine adapter plate. (fig. 12-25)
9. Disconnect the cable restraints holding the wire
harness to the lower chassis crossmember.
(fig. 12-22)
12-26
12-23 13. Loosen and disconnect the fuel lines (2) from the
engine. (fig. 12-26)
10. Disconnect the wire harness connections in the

upper right hand portion of the engine compart-
ment. (when viewed from the rear) (fig. 12-23)
12-6
Rubber Track Loader
12. Engine
12-27 12-31
14. Lay the angle iron across the fenders (or fuel tank Note: The rear cab window is directly over the lift point
if still in place) and attach one or two tie down of the engine. It is important to use an engine lifting
straps to serve as a sling to hold the hydraulic device that is low in profile and can reach forward
pumps up in position during engine removal. (fig. between the engine and chassis (as shown in fig. 12-
12-27) 30) or the rear window could be damaged. (fig. 12-31)
12-28
15. Disconnect the ground strap from the upper cross-

member. (fig. 12-28)
12-32
18. Slide the engine rearward to clear the forward

motor mounts, then up and out between the radia-
tor supports. (fig. 12-32)
12-29
Installation
1. To install the engine, reverse the removal proce-
16. Attach a lifting chain or cable to the lift points on dure.
the engine. (fig. 12-29)
Note: When reinstalling the engine, lightly grease the

rubber motor mount surfaces to allow the engine to
slide onto them without snagging or disfiguring them.
!WARNING!
Once the engine has been installed, make sure to
properly reconnect and install all items removed during
engine removal to ensure proper operation.
12-30 Prior to starting, make sure all fluids are at appropriate

levels and that they have not been contaminated with
17. Attach a device capable of safely lifting the engine dirt or debris during service. Change fluids or adjust
to the lifting chain as shown. (fig. 12-30) (see note) fluid levels as needed to ensure proper operation.
12-7
12-8
13. Undercarriage

dures for the undercarriages. the following undercarriage components.
• Idler Wheels (Removal and installation)
Note: For track removal and installation procedures, refer to • Bogie Wheels (Removal and installation)
pages 4-6 through 4-9 of this manual. • Hub Assembly Service Procedures
Note: For drive sprocket removal and roller inspection and Note: Procedures are provided for only those components
replacement, refer to page 4-5 of this manual. listed above. However, exploded parts diagrams exist in the
PT-70 and PT-80 parts manuals to serve as visual aids in the
removal and installation of other system components.
Personal Safety
!WARNING!
15” Idler Wheel (PT-80)
Track Loader can be dangerous and may result in Note: The 15” idler and 10” bogie wheels may be
removed from the PT-70 and PT-80 undercarriages
Do not attempt to perform any type of repair or mainte- without removing the tracks.
Removal
Refer to the Operation and Maintenance manual for Required Tools
instructions regarding proper machine operation tech- Socket/impact wrench
niques before operating any Rubber Track Loader. Heavy duty hydraulic jack
Combination wrench
Machine Preparation ASV approved jack stands (2)
Shop vac or Pressure washer
!WARNING!
Accidental machine starting can cause injury or even 1. Raise and support the machine by following the
death to personnel working on a Rubber Track Loader. jacking procedure on page 4-2.


chine to inform personnel that the machine is being Cavity
worked on.

13-1
2. Break up and remove any foreign material from the
cavity between the suspension rail and the drive
table support. (fig. 13-1)
Note: A shop vac or pressure washer will work well to

remove material from this cavity.
13-1
Rubber Track Loader
13. Undercarriage
3. Clean the threads on the turnbuckle thoroughly

using a stiff bristle brush.
13-2 13-6
7. Remove the outer scraper plate from the suspen-

sion rail. (fig. 13-6)
13-3
13-7
4. Loosen the lock nut on the turnbuckle and spin it
to the end of the threaded shaft to allow clearance
when the drive table is lowered. (fig. 13-2)
5. Rotate the turnbuckle and lower the drive table as
far as it will go. (fig. 13-3)
13-8
13-4 8. Remove the bolts securing the inner wheel to the

hub, then remove the wheel. (fig. 13-7, 13-8)
9. Repeat this procedure as necessary to remove the

15” idler wheels throughout the undercarriage.
Note: To remove the 10” bogie wheels on the PT-80

undercarriages, refer to page 13-3 of this manual.
Installation
1. To install the 15” idler wheels, reverse the removal
13-5
procedure. Torque the wheel mounting bolts
upon installation to 90 +/- 10 Lb. Ft.
6. Remove the bolts securing the outer wheel to
the hub. Then remove the wheel. (fig. 13-4, 13-5)
13-2
Rubber Track Loader
13. Undercarriage
10” & 15” Wheels (PT-70) 4. Repeat as necessary to remove the idler and
bogie wheels throughout the undercarriages.
Note: The 15” idler and 10” bogie wheels may be
removed from the PT-70 and PT-80 undercarriages Installation
without removing the tracks. 1. To install the idler wheels on the PT-70, reverse
the removal procedure. Torque the 15” wheel
mounting bolts upon installation to 90 +/- 10
Removal Lb. Ft. Torque the 10” wheel mounting bolts
Required Tools upon installation to 37 +/- 5 Lb. Ft.
Socket/impact wrench
Heavy duty hydraulic jack
Combination wrench
ASV approved jack stands (2)
Shop vac or Pressure washer
1. Perform steps 1-5 of the PT-80 15” idler wheel
removal procedure on page 13-1.
Remove bolts
13-11
13-9
2. Remove the bolts securing the wheel to the hub.

(fig. 13-9)
13-12
Bogie Wheel (PT-80 only)

Removal & Service Procedure
1. Perform steps 1-5 of the 15” idler wheel removal
13-10 procedure on page 13-1 to loosen the track and
provide clearance for bogie wheel removal.
Required Tools
3. Remove the wheel from the undercarriage. Combination/Socket Wrenches (including Allen)
(fig. 13-10) Press & Various Press Tooling
Torque Wrench
Note: Steps 2 and 3 are accurate for the removal of Bench Vise
both the 10” and 15” wheels throughout the PT-70
undercarriages.
13-3
Rubber Track Loader
13. Undercarriage
Note: Figure 13-36 incudes an exploded parts diagram

of the PT-80 undercarriage for your reference.
13-16
13-13 4. The inner and or outer bogie wheels may now be

removed with an impact wrench and allen socket
as shown in fig. 13-16. If necessary, clamp one
2. Remove the outer plate securing the assemblies to
wheel in a vise to keep the axle from spinning
the shaft. (Most plates will be a two bolt design.
while you remove the bolts.
The one bolt version is shown here.) (fig. 13-13)
Note: The wheel assemblies in the PT machines use
metal face seals to keep dirt/debris out of the wheel
bearings. During wheel removal/replacement, it is nec-
essary to remove, inspect and clean all components
prior to reassembly to ensure proper function.
Bolts
1/2 of face seal
13-14
13-17 Hub
5. Remove both wheels from the hub. (fig. 13-17)
Note: Take care not to drop the metal face seal halves.
The sealing surfaces are surface ground and have an
extremely fine finish. If scratched or disfigured, the
13-15 seal will not function as intended.
Also, take care not to lose the keys for indexing the
3. Loosen and remove the 4 bolts securing the bogie
wheels onto the shaft.
assemblies together around the mounting shaft.
(fig. 13-14, 13-15)
Note: Now is a good time to inspect the components
for damage or wear. If the bearings do not roll smooth-
ly when rotated, replace them. If the seals appear worn
or damaged, replace them. If the wheels are worn or
damaged, replace them. If the components appear to
be in good working condition, you may reuse them.
13-4
Rubber Track Loader
13. Undercarriage
Sealing Surfaces
Face Seal Halves
13-18 Rubber Seals
13-21
6. Once the wheels have been removed, use a press

to push the axle and far side bearing out of the
hub as shown. (fig. 13-20, 13-21)
7. If it is necessary to remove the other bearing for

replacement, press it out as well. If not, you may
leave this bearing in the hub during cleaning.
13-19
Note: The metal face seals are a 4-piece design with

one rubber outer seal and one metal face seal fitted
into each wheel and one rubber outer seal and one
metal face seal fitted into each hub. As they are
assembled, the metal halves mate and ride against
each other on a thin layer of oil to seal out dirt and
debris. Figure 13-18 shows the various components 13-22
that make up a face seal. Figure 13-19 shows the seal
as a mated assembly.
8. Clean all parts (including wheels) thoroughly with
parts cleaning solution and dry them prior to
reassembly. Wipe the inner hub surfaces to
remove any solvent or oil residue. (fig. 13-22)
13-20 13-23
9. Reinstall the bearing and shaft into the hub as

found upon disassembly, then press the bearing
back into the hub over the shaft. (fig. 13-23)
13-5
Rubber Track Loader
13. Undercarriage
10. Disassemble and clean the face seals and their

rubber outer seals thoroughly, then wipe them dry
to ensure a good seal when assembled.
13-27A 13-27B
13-24 13. Once the seals are in place, wipe the mating sur-
faces of the face seals with a clean shop cloth and
alcohol in a circular motion ending in a gentle
11. Once the seals and hub have been thoroughly sweep from the inside to the outside of the face
cleaned and dried, reinstall the hub portion of the until clear of the face.This will ensure a clean mat-
face seal into the hub as shown. Make sure to ing surface and a good seal. (fig. 13-26, 13-27)
work the rubber seal down into place within the
hub (until it seats) to ensure a good seal. 14. Apply a very thin coating of fresh 10W30 engine
(fig. 13-24) oil onto the seal faces (faces only) in a circular
motion to provide lubrication and help them seal.
Seal Surfaces
13-25
13-28
12. Similarly, reinstall the wheel portion of the face

seal into the (clean) wheel. Make sure to work the 15. Align the wheel hub and axle, then slide the wheel
rubber seal down into place within the wheel (until back onto the axle/hub assembly as shown in fig-
it seats) to ensure a good seal. (fig. 13-25) ure 13-28.
13-29
16. Install the key into the opening in the axle/hub

assembly as shown. (fig. 13-29)
13-26
13-6
Rubber Track Loader
13. Undercarriage
13-30
13-34
17. Apply red (high strength) thread locking compound
to the wheel retaining bolt as shown. (fig. 13-30)
21. Remove the allen plug from the center of the hub
assembly and fill it with 2 ounces of ASV 10W-30
Heavy Duty Engine Oil. Then reinstall the plug.
(fig. 13-33, 13-34)
22. Repeat this procedure on the other half of the

bogie assembly if necessary prior to installing the
two halves back onto the undercarriage.
13-31
18. Install the bolt and tighten it. (fig. 13-31)
19. If you haven’t already, repeat steps 10-18 of this

procedure on the other side of the hub/wheel
assembly to secure the second wheel in place.
13-35
23. Place the rubber rods back into position on the

square shaft, then tape them in place to keep
them secure while installing the bogie assemblies
around them. (fig. 13-35)
24. Reverse steps 1-3 of this procedure to reinstall the

13-32
bogie assembly back onto the undercarriage and
complete the procedure.
20. Once the hub/wheel assembly is together as
shown, torque the wheel retaining bolts to 180 ft. 25. Repeat this procedure as necessary throughout
lbs. to secure them in place. (fig. 13-32) the PT-80 undercarriage to restore proper function.
13-33
13-7
Rubber Track Loader
13. Undercarriage
Note: The hubs on PT-70 & PT-80 machines

are very similar in design. The components,
although not identical, are serviced in the same
manner. Please note any differences between
the two machines during disassembly to aid
during reassembly. (see notes in procedure)
Hub Tool Kits

PT-70: 0403-475
13-36 PT-80: 0403-339
Idler Hub Note: If you are removing the outer or rear hub
assemblies you will be able to remove the hub assem-
Service Procedure PT-70 & 80 (80 shown) bly once step three is complete.
Required Tools
Socket Wrench & Sockets (including Allen)
Press & Tool Kit (PT-70: 0403-475 or PT-80: 0403-339)
Snap Ring Pliers
1. Remove the hub assemblies from the undercar-
riages as required first by following steps 1-7 of
the track removal procedure on page 4-6. Then
proceed to the steps below. Part #: 0403-336
2. Remove the snap ring (item 22) securing the cap

(item 23) in the hub assembly. (fig. 13-36)
13-38 PT-70 use tool #: 0403-375
3. Remove the nut (item 24) and the washer (item
25), then remove the hub assembly from the axle
shaft. (fig. 13-36) (see note below)
Axle
13-39
13-37
4. Using a press and tool # 0403-336, press the

Note: If you are removing the inner front hub assem- bearing sleeve out of the hub assembly. (fig. 13-
bly, you will have to slide the axle (item 26) out of the 38, 13-39)
main rail weldment to remove it. (fig. 13-36, 13-37)
13-8
Rubber Track Loader
13. Undercarriage
Part #: 0403-337
Rear race Part #: 0403-333
13-40 13-43
PT-70 use tool #: 0403-371
5. Remove the bearing out of the front of the hub as 7. If bearings are to be replaced, press the rear bear-
shown. (fig. 13-40) ing race out of the assembly from the front of the
hub with tools 0403-337 and 0403-333. (fig. 13-43)
Center seal
Front race
Part #: 0403-336
13-41
13-44
PT-70 use tool #: 0403-375
Part #: 0403-337 8. Press the bearing sleeve out of the rear bearing
Part #: 0403-334 using tool 0403-336. (fig. 13-44)
Center seal
Retaining ring
Front race
13-42 PT-70 use tools #: 0403-372 & 0403-375
6. Press the center seal and front bearing race out of 13-45
the assembly from the rear of the hub using tools
0403-337 and 0403-334. (fig. 13-41, 13-42) 9. Remove the face seals and retaining ring from the
bearing sleeve for cleaning and or replacement.
Note: The center seal will be destroyed during removal (fig. 13-45)
and must be replaced upon reassembly.
Note: There is no retaining ring on PT-70 machines.
13-9
Rubber Track Loader
13. Undercarriage
Note: Take care not to drop the metal face seal halves.
The sealing surfaces are surface ground and have an
extremely fine finish. If scratched or disfigured, the
seal will not function as intended.
Note: Now is a good time to inspect the components

for damage or wear. If the bearings do not roll smooth-
ly when rotated, replace them. If the seals appear worn Part #: 0403-330
or damaged, replace them. If the wheels are worn or
damaged, replace them. If the components appear to
be in good working condition, you may reuse them. 13-48
PT-70 use tool #: 0403-373
10. Thoroughly clean all parts with parts cleaning solu- 14. If the rear race has been removed, press it into the
tion and gently blow them clean with air if neces- hub from the rear until properly seated with tool #:
sary, then wipe dry. 0403-330, then install the clean, dry bearing.
(fig. 13-48)
11. Disassemble and clean the face seals and their
rubber outer seals thoroughly, then wipe them dry Part #: 0403-337
to ensure a good seal when assembled. Part #: 0403-338
13-49
13-46
12. Once components are clean and dry, install half of

the rear face seal into the bearing sleeve. Make
sure to work the rubber seal down into place within
the seal recess (until it seats) to ensure a good
seal. (fig. 13-46) 13-50
15. Install the seal/retaining ring assembly into the rear

of the hub and press into place until seated using
the tools shown above. (fig. 13-49, 13-50)
13-47
13. Install the other half of the rear face seal into the
retaining ring. Make sure to work the rubber seal 13-51
down into place within the ring (until it seats) to
ensure a good seal. (fig. 13-47)
13-10
Rubber Track Loader
13. Undercarriage
Part #: 0403-335
13-52 13-55 PT-70 use tool #: 0403-374
16. Once the seals are in place, wipe the mating sur- 19. Flip the hub over, support the bearing sleeve from
faces of the face seals with a clean shop cloth and the bottom with tool 0403-335 and set it onto the
alcohol in a circular motion ending in a gentle press for center seal installation. (fig. 13-55)
sweep from the inside to the outside of the face
until clear of the face.This will ensure a clean mat-
ing surface and a good seal. (fig. 13-51, 13-52)
13-56
13-53 20. Install the center seal into the hub. Work the lip
around the bearing sleeve with your fingers prior
to pressing it into place. (fig. 13-56)
17. Apply a very thin coating of fresh 10W30 engine
oil onto the now clean seal faces (faces only) in a
circular motion. (fig. 13-53)
13-57
13-54 21. Install the race into the hub as shown above the
PT-70 use tool #: 0403-375 seal. When the race is pressed into place, it will
push the seal into position. (fig. 13-57)
18. Press the bearing sleeve assembly (with face seal
clean, installed, and oiled) into the hub with tool Note: See step 22 for tool information and race instal-
0403-336 until seated. (fig. 13-54) lation instructions.
13-11
Rubber Track Loader
13. Undercarriage
Part #: 0403-330
13-58 PT-70 use tool #: 0403-373 13-61
22. Press the outer bearing race into the hub with tool 26. Remove the allen plug in the center portion of the
# 0403-330 until it seats. (fig. 13-58) hub. (fig. 13-61)
Part #: 0403-333
13-59 PT-70 use tool #: 0403-372 13-62
23. Pack the bearing with ASV Multi-Purpose EP 27. Add 2 oz. (1 oz. PT-70) of ASV 10W-30 Heavy
Lithium Grease and then install it onto the bearing Duty Engine Oil to the hub as shown, then reinstall
sleeve using tool 0403-333. (fig. 13-59) the plug and tighten. (fig. 13-62)
24. Press it into the assembly until it gently seats into

the bearing race. (fig. 13-59)
13-63
13-60 28. The hub assembly is now ready to be reinstalled.

To install it onto the machine, reverse steps 1-3 on
page 13-8 of this procedure. Make sure to read
25. If necessary, use a needle dispenser to fill any the note below step 3 prior to reinstalling.
places in the bearing that are not full of grease to (fig. 13-63)
ensure adequate lubrication. (fig. 13-60)
29. Repeat this procedure throughout the undercar-
riage as necessary to repair worn or damaged
components and restore proper function.
13-12
14. Lift-Arm Components

dures for the lift-arm components. the following lift-arm components.
Personal Safety • Lift Cylinder

• Bucket/Tilt Cylinder
!WARNING! • Quick Coupler Block PRV
Track Loader can be dangerous and may result in Note: Procedures are provided for only those lift-arm compo-
machine damage, injury or even death. nents listed above. However, exploded parts diagrams exist
in the PT-70 and PT-80 Parts manuals to serve as visual
Do not attempt to perform any type of repair or mainte- aids in the assembly and disassembly of other system com-
nance on a Rubber Track Loader until you have read and ponents.
Note: Refer to page 3-1 through 3-3 for pictorial views of
Refer to the Operation and Maintenance manual for the hydraulic systems and components.
Lift Cylinder
Accidental machine starting can cause injury or even Combination/Open End/Socket Wrenches
death to personnel working on a Rubber Track Loader. Hydraulic Caps/Plugs (various sizes)
ASV Approved Jack Stand (or equivalent)
As a precaution, disconnect the battery cables from the Pin Removal Tool (ASV P/N: 2045-277)
the key from the ignition switch prior to performing any NOTICE
Cap and plug all fittings and hoses to prevent fluid loss
Place a “Do Not Operate” tag prominently on the ma- and or contamination during service work.
worked on. !WARNING!
Remove any attachment, lower or safely support the lift
arms and make sure the hydraulic oil is cool before
Rubber Track Loader, read and understand Chapter 1 removing any components or lines. Hot or pressurized
(Product Safety) for personal safety information. oil can cause personal injury.
NOTICE
The hydraulic system fluid should be changed follow-
ing any hydraulic component service according to the
procedure described on page 4-16.
14-1
Rubber Track Loader
14-4
14-1
4. Remove the bolts securing the front and rear lift
arm cylinder pivot pins to the lift arm and lift arm
1. Rest the lift arms on an ASV approved jack stand tower. (fig. 14-4)
to provide clearance for lift cylinder removal. (fig.
14-1)
14-5
5. Remove the grease fitting from the pivot pins to

14-2 allow the installation of the pin removal tool. (fig.
14-5)
2. Disconnect the inlet and outlet hoses from the

cylinder. (fig. 14-2)
14-6
6. Thread the removal tool into each pin, then use

the slide hammer to extract them. (fig. 14-6)
14-3
3. Label the hoses according to right and left orienta-

tion to simplify reassembly, then cap and plug the
hoses and fittings to prevent fluid loss and or sys-
tem contamination. (fig. 14-3)
14-2
Rubber Track Loader
Bucket/Tilt Cylinder
Removal
Required Tools
Socket Wrench
Hammer
Punch (brass)
14-7
7. Remove the cylinder from the machine for service

or inspection. (fig. 14-7)
Note: At this time the pivot bushings and pivot pins are 14-8
easily accessible for replacement. Inspect them for vis-
ible wear or damage and replace them as necessary .
1. Raise the lift arms and support them with the lift
arm brace as described on page 4-1. (fig. 14-8)
Installation
1. To install the lift arm cylinder, reverse the removal
procedure.
14-9
2. Place a suitable catch container beneath the cylin-

der fittings, then disconnect the inlet and outlet
hoses from the cylinders. (fig. 14-9)
3. Cap and plug the hoses and fittings to prevent fluid

loss and or system contamination.
14-3
Rubber Track Loader
14-10 14-13
4. Remove the bolt securing the lower pin to the 7. Use a pry bar to slide the lower pin out of the cylin-
quick attach. (fig. 14-10) der end allowing it to be removed. (fig. 14-13)
14-11
14-14
5. Remove the bolt securing the upper pin to the lift
arm weldment. (fig. 14-11)
8. Use a pry bar to pry the lower cylinder eyelet out
Disconnect of the upper Q/A mount as shown. (fig. 14-14)
14-12
6. Disconnect the outer quick attach cylinder hose (if 14-15

equipped) to allow the lower pin to be removed.
(fig. 14-12)
9. Use a hammer and a brass punch to tap the upper
pin most of the way out of the lift arm weldment.
(fig. 14-15)
Note: Make sure to support the cylinder (have an

assistant support it if necessary) while removing the
upper pin to prevent it from falling and being damaged
or from causing injury to anyone standing underneath.
14-4
Rubber Track Loader
Quick Coupler Block PRV

Removal
Required Tools
Combination Wrench
14-16
10. Remove the pin from the cylinder while supporting

the cylinder. (fig. 14-16)
14-18
1. With the machine off and cool and with all

hydraulic actuators relaxed, loosen the pressure
release valve on the top of the auxiliary quick cou-
pler block. (fig. 14-18)
14-17
11. Remove the cylinder from the machine. (fig. 14-17)
Installation
1. To install a bucket/tilt cylinder, reverse the removal
procedure.
14-19
2. Once loose, remove the valve from the block by

twisting it counter-clock-wise until free. (fig. 14-19)
Installation
1. To install the Q/C PRV, reverse the removal proce-
dure.
14-5
14-6
15. Quick Attach

dures for the quick attach and associated components. the following quick attach components.
Personal Safety • Quick Attach locking Pin Assemblies

• Quick Attach Pivot Pins
!WARNING!
Improper or incomplete maintenance/repair of a Rubber Note: Procedures are provided for only those quick attach
Track Loader can be dangerous and may result in components listed above. However, exploded parts diagrams
machine damage, injury or even death. exist in the PT-70 and PT-80 Parts manuals to serve as visu-
al aids in the assembly and disassembly of other system
Do not attempt to perform any type of repair or mainte- components.
fully understood the information in this manual. Locking Pin Assembly
Refer to the Operation and Maintenance manual for Removal
niques before operating any Rubber Track Loader. Required Tools
Combination/Open End/Socket Wrenches
Machine Preparation ASV Approved Jack Stand (or equivalent)
!WARNING! !WARNING!
Remove any attachment, lower or safely support the lift
arms and make sure the hydraulic oil is cool before
removing any components or lines. Hot or pressurized
oil can cause personal injury.

worked on.

15-1
1. Rest the lift arms on an ASV approved jack stand

to provide clearance for quick attach disassembly.
(fig. 15-1)
15-1
Rubber Track Loader
15. Quick Attach
Upper guard
15-5
15-2
5. Remove the pivot link from the quick attach.
2. Remove the bolts (3) securing the upper guard to (fig. 15-5)
the quick attach weldment. (fig. 15-2)
Upper guard
15-6
6. Slide the locking pin assembly out of the quick

attach. (fig. 15-6)
15-3
3. Remove the upper guard from the quick attach.

(fig. 15-3)
15-7
Note: At this time the locking pin assembly compo-

nents are easily accessible for replacement. Inspect
15-4 them for visible wear or damage and replace them as
necessary .
4. Remove the bolt securing the locking pin assembly
to the locking cylinder or latch handle. (fig. 15-4) Pay attention to the quantity and position(s) of each
component to aid during reassembly. (fig. 15-7)
Installation
1. To install the quick attach locking pin assembly,
reverse the removal procedure.
15-2
Rubber Track Loader
15. Quick Attach
Pivot Pin (quick attach)

Removal
Required Tools
Combination/Open End/Socket Wrenches
ASV Approved Jack Stand (or equivalent)
Hammer
Punch (brass)
15-8
1. Rest the lift arms on an ASV approved jack stand

to provide clearance for quick attach disassembly.
(fig. 15-8)
Remove bolt & nut
Drive out
15-9
2. Remove the bolt securing the pivot pin to the quick

attach weldment, then drive the pin out with a
hammer and brass drift punch. (fig. 15-9)
Note: There are four pivot pins that connect the quick
attach to the lift arm and cylinders. All four pins are
removed in a similar manner.
Installation
1. To install the quick attach pivot pins, reverse the
removal procedure.
2. Repeat this process as necessary to remove and

replace worn or damaged quick attach pins.
15-3
15-4
NOTICE
Disassembly of hydraulic components should only be performed 16. Hydraulic Component
by factory trained personnel experienced in the disassembly
and repair of hydraulic components. Components should not be
serviced during the warranty period without written instruction
Service Procedures
from the ASV service department. Component disassembly dur-
ing this period may void the manufacturer’s warranty.
Chapter Overview Disassembly & Assembly

This chapter provides information on inspection, disas- Disassembly and assembly procedures are provided
sembly and assembly of major hydraulic components. for the following components:
• Hydraulic Cylinders
• Lift Arm Control Valve
Personal Safety • Drive motor
!WARNING! • Drive Pump
• Auxiliary Pump
Note: Procedures are provided for only those components
listed above. However, exploded parts diagrams exist in the
PT-70 & PT-80 parts manuals to serve as visual aids in the
assembly and disassembly of other system components.
Hydraulic Cylinder
Disassembly
niques before operating any Rubber Track Loader. Required Tools
Bench Vise
Prior to performing any type of service work on a Pipe Wrench
Rubber Track Loader, read and understand Chapter 1 Socket or Impact Wrench
(Product Safety) for personal safety information. Screwdriver (blade type)
Rubber or Dead Blow Hammer
!WARNING! Small Pry Bar
When servicing any hydraulic component, make sure
the machine is off and cool and that all of the hydraulic
actuators are relaxed prior to disconnecting or remov-
ing any component from the system.
NOTICE
When servicing any hydraulic component, keep in
mind that any scratches or damage that can be felt
with a fingernail on surfaces that parts move, slide, roll
or rotate upon indicate a need for part replacement. 16-1
Hydraulic components must be kept extremely clean to

ensure proper function and service life. Do not assem- 1. With machine off and cool and with hydraulic actu-
ble any components that have not been inspected for ators relaxed, disconnect and cap hoses from the
damage and thoroughly cleaned prior to assembly. cylinder(s) to be serviced.
The hydraulic system fluid should be changed fol- Note: When servicing cylinders, the attached components
must be supported in a manner that allows the cylinders to
lowing any hydraulic component service according
be safely removed and installed. (lift arms & quick attach)
to the procedure described on page 4-16.
2. Remove the cylinder(s) and secure it in a bench
vise to aid in disassembly. (figure 16-1)
3. Place a suitable catch container beneath the rod

end of the cylinder to catch any hydraulic oil that
may leak out upon disassembly.
16-1
Rubber Track Loader
16. Hydraulic Component Service
Cylinder Tube Weldment
16-2 16-5
4. Use an open end or pipe wrench to turn and 7. With the piston and rod removed from the cylinder,
remove the end gland. (figure 16-2) inspect the cylinder bore for scratches or other
damage. If any are present that are deep enough
to catch with your fingernail, the cylinder tube
End Gland weldment should be replaced. (figure 16-5)
Rod
16-3
5. Use a pry bar or similar device to pull the rod and 16-6
piston from the cylinder. (figure 16-3)
Piston 8. Remove the nut from the rod end. (figure 16-6)
Ring Seals
16-4
16-7
6. Inspect the piston surface, seals and ring for wear
or damage. If any component appears to be dam-
aged in any way, replace it. When inspecting the 9. Support the piston loosely from the underside (fig-
piston surface, look for scratches. If any are pres- ure 16-7), thread the nut partially on to protect the
ent that are deep enough to catch with your finger- threads and tap the rod end with a rubber or dead
nail, the piston should be replaced. (figure 16-4) blow hammer to free the piston from the rod.
Note: Seal imperfections or scratches on the piston, bore or 10. Once loose, remove the nut and piston from the
rod or will cause internal/external leakage and impaired func- rod.
tion. Defective components must be repaired or replaced.
16-2
Rubber Track Loader
16-8 16-11
13. Remove the tandem seals from the end gland pay-
ing close attention to the order of removal to aid
during installation of the new seals. (fig. 16-11)
16-9
11. Remove the seals and piston ring taking care not 16-12
to scratch the piston. Also, pay close attention to
seal and ring orientation and position to aid when 14. Remove the inner seal from the end gland. Pay
installing new parts. (figures 16-8, 16-9) attention to the seal orientation upon removal to
aid during installation of the new seal. (fig. 16-12)
15. Remove the end gland outer seal from the end
gland. (figure 16-10)
Outer Seal 16. Thoroughly clean all parts to prevent contamina-

tion of hydraulic oil when reinstalled.
Assembly
1. Install new seals and components in place of the
16-10 originals paying close attention to orientation and
location to ensure proper operation.
12. Gently tap the end gland off of the cylinder rod. 2. Lubricate the piston, ring, and seals with fresh
(figure 16-10) hydraulic oil prior to assembly to avoid damage.
3. Reassemble components by reversing the disas-

sembly process.
Note: During reassembly, use an impact wrench to tighten

the piston retaining lock nut. Make sure the nut is tight and
that there is no independent movement between the piston
and rod before reassembling.
16-3
Rubber Track Loader
Lift Arm Control Valve 4. Remove each valve section and inspect the seals
for damage, replace if necessary. (figure 16-15)
Disassembly
Required Tools
O-ring
Socket Wrench
Combination Wrench
Screwdriver (blade type)
Low Profile Needle Nose Pliers
1. With machine off and cool and with hydraulic actu-

ators relaxed, remove the lift arm control valve
according to the procedure on page 10-4. 16-16
2. Place the valve on a bench in a clean work area.
16-17
5. Remove the inlet port assemblies and inspect the

seals for damage, replace if necessary.
16-13
(figure 16-16, 16-17)
16-18
16-14
6. Once the inlet port covers have been removed
from both sides of a spool, the spool may be
3. Remove the nuts holding the valve stack together. removed. (fig. 16-18)
(figure 16-13, 16-14)
O-ring
16-15
16-4
Rubber Track Loader
16-22
16-19
8. Remove the spring from the spool. (fig. 16-22)

Note: Figure 16-19 displays the assembly order of the
spool and associated components.
Spool Load Check Spring Cap

Spool
16-20
Note: The lift arm and bucket control spools are each 16-23
equipped with a unique load check spool. The load
check spools provide bucket positioning (self-Leveling).
9. Remove the load check spool with a low profile
The components can be seen above in figure 16-20.
needle nose pliers. (fig. 16-23)
The load check spools are similar, but they are not
identical. The main spools are also unique. All
spools must be reinstalled as found upon disas-
sembly to function properly.
Clamp
16-24
Note: There is a passageway in the load check spool

that must be kept clear to ensure proper operation. It
16-21 Cap Spool leads from the small hole in the side of the spool to the
end of the spool. If you cannot blow air through this
passageway, it must either be cleaned or the load
check spool must be replaced to restore proper func-
7. To remove the load check spool, use a clamp to
tion. (fig. 16-24)
hold the spool in place in a vice without damaging
the spool and remove the end cap with an allen
wrench. (fig. 16-21)
16-5
Rubber Track Loader
Assembly Drive Motor (brake portion)

1. Install new seals and components in place of the Disassembly
originals as necessary paying close attention to
Required Tools
location and orientation to ensure proper function.
Allen Wrench/Socket
2. Thoroughly clean all components to prevent sys- Rubber Mallot (seal removal if needed)
tem contamination. Screwdriver (blade type) (seal removal if needed)
3. Reassemble components by reversing the disas- ators relaxed, remove the drive motor from the
sembly process. undercarriage by following the procedure in sec-
tion 13.
16-25
2. Remove all but four of the allen bolts (on opposite

sides of the cover) holding the rear cover onto the
drive motor, then back the remaining four out
evenly to release the light spring pressure against
the cover. (fig. 16-25)
16-26
3. Remove the rear cover to expose the brake

assembly. (fig. 16-26)
16-6
Rubber Track Loader
Shims
Seal
Bolts
16-27 Spring 16-30
4. Remove the brake spring and shims. Make sure to 9. Inspect the seal for any damage. (fig. 16-30)
note the order of assembly to ensure correct
reassembly. (fig. 16-27) 10. Remove the allen bolts securing the upper casting
to the drive motor. (fig. 16-30)
16-28
16-31
5. Insert an air nozzle into the port closest to the rear

of the pump as shown. (fig. 16-28) 11. Remove the upper casting from the drive motor to
expose the clutch discs. (fig. 16-31)
6. Cover the opening with a shop cloth and apply
moderate pressure to the top of the brake piston to
keep it in place when air is applied. (fig. 16-28)
7. Apply air to the port and the piston should slide

upwards so that it can be removed.
Note: There is a seal around the outer edge of the pis-

ton so it may pop loose rather than gently slide out.
16-32
12. Inspect the discs for discoloration (blueing) or for

signs of excessive wear. (fig. 16-32)
Note: If any of the individual discs measure less than

.015” replace them as a set.
Seal
Assembly
16-29 1. Replace worn or damaged components, thorough-
ly clean all parts, then reassemble the motor by
reversing the disassembly procedure.
8. Remove the piston from the motor. Inspect the
seal for any damage. (fig. 16-29)
16-7
Rubber Track Loader
Drive Motor (motor portion)

Disassembly
Required Tools
Allen Wrench/Socket
Snap Ring Pliers
Screwdriver (blade type) (seal removal if needed)
Surfaces
16-36
3. Lift and remove the piston block to expose the

sealing surfaces. Inspect these surfaces to ensure
there is no scratching or abrasion that may affect
operation. (fig. 16-36)
16-33
Surfaces
1. Mark the casing across the parting lines as shown

to ensure correct reassembly of the drive motor.
(fig. 16-33)
Bolts
16-37
4. Inspect the surfaces of the cam ring and the piston

rollers for imperfections. Any damage found indi-
cates a need for component replacement.
(fig. 16-37)
16-34
16-38
16-35
5. Using a snap ring pliers, remove the snap and
retaining rings on both sides of the piston block to
2. Remove the allen bolts securing the output end of allow for removal and inspection of the block, pis-
the drive motor to the main casting and remove it tons, piston rings, and rollers. (fig. 16-38)
from the motor as shown. (fig. 16-34, 16-35)
16-8
Rubber Track Loader
Drive Pump (Drive Relief Valves)

Disassembly & Adjustment
Required Tools
Allen Wrench/Socket
Combination/Socket wrench
ators relaxed, remove the drive pump from the
machine by following the procedure in section 11.
16-39
Ring Groove
Ring
16-42
16-40
6. Once the snap rings and retainers are removed,

slide the piston assemblies out one at a time and
inspect them for damage. (fig. 16-39, 16-40)
16-43
Note: While inspecting the piston assemblies, pay
close attention to the piston ring. Look for any signs of
damage or cracking. (fig. 16-40) 2. Remove the drive pressure relief valves as shown
in fig. 16-42 and 16-43.
16-41
16-44
7. Inspect the rollers and sleeves as well to make
sure there are no scratches or other damage that 3. If adjustment is needed (see drive pressure check
may affect operation. procedure in section 17), loosen the allen type set
screw on the valve.
Assembly
1. Replace worn or damaged components, thorough-
ly clean all parts, then reassemble the motor by
reversing the disassembly procedure.
16-9
Rubber Track Loader
Drive Pump
Disassembly
Required Tools
Allen Wrench/Socket
Rubber Mallot
Snap RIng Pliers
16-45
4. Flip the valve over, then tighten the nut to increase

the pressure setting (CW) or loosen it to decrease
the pressure setting (CCW).
Assembly & Test

1. Retighten the locking set screw and reinstall by
reversing the disassembly procedure. Retest the
pressure through the affected relief to check for 16-47
proper adjustment. If it is still not correct, repeat
the adjustment procedure until correct.
Note: The drive pump is a tandem design where two
pumps share one housing. The disassembly and
Drive Pump (Posi-Power Relief Valve) assembly procedures are identical for both pumps.
Removal 1. Remove the allen bolts securing the end cap onto
Required Tools the pump. (fig. 16-47)
16-48
16-46
2. Remove the end of the pump as an assembly
(fig. 16-48)
Note: The posi-power relief valve is usually a remove
and replace item. However, If adjustment is required,
please see the posi-power relief valve adjustment pro-
cedure in section 17 of this manual.
1. Remove the valve from the drive pump as shown

in figure 16-46.
Installation
1. To install, reverse the removal procedure.
16-10
Rubber Track Loader
Bearings
Swash Plate
16-49 16-52
3. Remove the valve plate and inspect it for damage

or wear, specifically, scratches that can be felt with
a fingernail. (fig. 16-49) Surfaces
Barrel Face
16-53
5. Remove the swash plate along with the bearings

16-50 and inspect them for any damage or scratching
that could affect operation. (fig. 16-52, 16-53)
Slipper Faces
16-51 16-54
4. Inspect the end of the barrel (face) and the slipper 6. Remove the snap ring holding the shaft, seal and
faces for similar scratches. (fig. 16-50, 16-51) bearing into the casing, then remove the seal.
(fig. 16-54)
Note: To inspect the slipper faces, slide the barrel off
of the assembly, then slide the slippers and pistons off Note: If you are repairing the existing pump, you will
of the shaft as an assembly, then inspect. need to replace the outer seal as it will be destroyed
upon removal.
16-11
Rubber Track Loader
Drive Pump
Assembly
Required Tools
Allen Wrench/Socket
Rubber Mallot
Snap RIng Pliers
16-55
7. Using a rubber mallot, gently tap the shaft and

bearing out of the casing for inspection or replace-
ment. (fig. 16-55)
16-56
1. Using a rubber mallot, gently tap the shaft and

bearing into the casing until seated. (fig. 16-56)
16-57
2. Replace the seal with a new one and install taking

care not to damage it upon installation. (fig. 16-57)
3. Install the snap ring that secures the shaft, bear-

ing, and seal in place. (fig. 16-57)
16-12
Rubber Track Loader
16-58 16-61
4. Flip the assembly over and lay it on a table, then 7. Once the pivots are installed, check to make sure
remove the pivot caps from both sides as shown. both of them are properly mated with the pins.
(fig. 16-58) Using a blade type screwdriver, turn the pivots
slightly to the right or left. The swash plate should
Note: Behind each cap is a pivot that aligns with the move with the pivot as each one is turned. If it
two small pivot wires attached to the swash plate. does not move, repeat step 6, then recheck. Once
Remove these from their cavities while installing the correct, reinstall the caps to secure them in place
swash plate. (fig. 16-61)
Long end
Pin
16-59 16-62
5. Assemble the bearing halves to the bottom of the 8. Reassemble the piston and barrel portion of the
swash plate, orient the pins so that they are verti- pump as found upon disassembly, then slide it
cal and then lower the assembly into place over back into the housing. (fig. 16-62, 16-63)
the shaft. (fig. 16-59)
Note: Make sure the long end of the swash plate
alignment bar is pointing inward to ensure proper oper-
ation. (fig. 16-62)
Pin
16-60 16-63
6. Once installed, make sure each pin is centered in 9. Reinstall and tighten the cover bolts to secure the
its opening, then slide the pivot into the hole so cover. (fig. 16-63)
that it mates with the pin. (fig. 16-60)
16-13
Rubber Track Loader
Auxiliary Pump
Disassembly
Required Tools
Allen Wrench/Socket
Snap Ring Pliers
O-ring
ators relaxed, remove the drive pump from the
machine by following the procedure in section 11.
16-67
5. Lift the cover off to expose the pump components

and the o-ring seal. Inspect the o-ring for damage,
replace if necessary. (fig. 16-67)
16-64
Inspect Face
2. Remove the bolts securing the relief valve to the

housing. (fig. 16-64)
O-rings
16-68
6. Inspect the valve plate face (both sides) for

scratches or any other damage that can be felt
with a fingernail. (fig. 16-68)
16-65
Inspect Face
3. Inspect o-rings for proper shape and condition.
Replace if necessary. (fig. 16-65)
16-69
7. Inspect the barrel face for scratches or any other

damage that can be felt with a fingernail.
16-66 (fig. 16-69)
4. Remove the Allen bolts securing the cover onto the

pump. (fig. 16-66)
16-14
Rubber Track Loader
Inspect Faces
16-70
8. Remove the piston/barrel assembly and inspect

the slipper faces for scratches or any other dam-
age that can be felt with a fingernail. (fig. 16-70)
Assembly
1. To reassemble, reverse the disassembly proce-
dure.
16-15
16-16
17. Hydraulic Pressure/Flow
Test & Troubleshooting
Chapter Overview Hydraulic Pressure/Flow Test &

This chapter provides hydraulic pressure and flow Troubleshooting Procedures
check, adjustment and troubleshooting procedures. Test and troubleshooting procedures are provided for
the following Hydraulic system components.
Personal Safety
• Charge Pressure Check & Adjustment
!WARNING! • Auxiliary Valve Pressure Check & Adjustment
Improper or incomplete maintenance/repair of a Rubber • Lift Arm Pressure Check & Troubleshooting
Track Loader can be dangerous and may result in • Drive Pressure Check & Troubleshooting
machine damage, injury or even death. • Auxiliary Flow Test & Troubleshooting
Do not attempt to perform any type of repair or mainte- When checking hydraulic system pressures, you are
nance on a Rubber Track Loader until you have read and essentially reading the relief valve settings of each cir-
cuit tested. If your hydraulic system and components
Refer to the Operation and Maintenance manual for are functioning properly, your readings should match
instructions regarding proper machine operation tech- those specified. If they differ, adjustment and or repair
niques before operating any Rubber Track Loader. may be required to restore proper function.
Prior to performing any type of service work on a The procedures in this section are listed in the
Rubber Track Loader, read and understand Chapter 1 order they are to be performed. When a pressure
(Product Safety) for personal safety information. issue is suspected, perform these procedures to help
diagnose and or repair the problem.
NOTICE
Hydraulic oil must be at operating temperature to
obtain accurate readings during the pressure and flow
Charge Pressure Check
test procedures described in this section. Start and Charge pressure is used to prime the various circuits,
warm the engine and hydraulic oil prior to performing including the joysticks, with hydraulic oil for operation.
the test and troubleshooting procedures in this section. Low charge pressure could lead to sluggish operation
of any and all functions.
Contamination Inspection Required Tools
The hydraulic system can become contaminated when Pressure Gauge 0-1000p.s.i.
one or more of it’s dynamic components fails or begins
to wear excessively. This can introduce significant
amounts of debris into the hydraulic oil.
In the event of contamination, the defective compo-

nent(s) must be replaced, the remaining components Test Port (A)
must be inspected and thoroughly cleaned (if found to
be reusable) and the system lines and reservoir must
be thoroughly flushed to restore original function.
The hydraulic filters remove contaminants from the oil.

Small amounts of debris found within the filters are to
17-1
be expected, but If there is significant metallic debris
found in either filter, certain components of your Note: The quick coupler (test port A) located in the engine
hydraulic system may be contaminated. To inspect for compartment just inside the left lift arm tower can be used for
contamination, label the hydraulic filters by location general pressure checks and troubleshooting.
and remove them. Cut them apart approx. halfway
between the top and bottom of the filter and inspect
them for debris. If contamination is suspected, contact
the ASV service department at 1-800-346-4367.
17-1
Rubber Track Loader
17. Hydraulic Pressure & Flow
1. Attach the gauge to test port A. (fig. 17-1) Route

the gauge so that you or an assistant can read it Charge Relief
during testing.
2. Make sure any bystanders are clear of moving

components, then start the engine.
3. Allow the engine to warm up to operating tempera-

ture, then with the engine at idle, check the charge
pressure. Record your reading. It should read 475
+/- 30 psi at this test port. If your reading differs,
17-2
adjustment is necessary.
4. If necessary, adjust the charge relief pressure.

To adjust:
a) Tilt the cab as described on page 4-2 of this
manual to access the pump.
b) Locate the charge relief valve on the top of the

drive pump. (fig. 17-2)
c) Remove the relief valve from the top of the

pump as shown in figure 17-3.
17-3
d) Add shims to increase the pressure setting, or
remove shims to decrease the setting until
within specification. (figure 17-4)
5. Retest once adjustments have been made to make

sure pressure is correct. Readjust as necessary
until correct.
17-4
17-2
Rubber Track Loader
Auxiliary Pressure Check

Required Tools
Test Port (B)
Pressure Gauges 0-1000, 0-6000 p.s.i.
Auxiliary pressure is used to drive flow style attach-
ments. Low auxiliary pressure can produce poor per-
formance in attachments while high pressure can
cause component damage/failure in the machine or the
attachment being utilized.
17-5
Note: Make sure charge pressure is set correctly prior to
testing this function.
1. Tilt the cab as described on page 4-2 of this

manual to access the valve.
2. Locate the test port on the top of the lift arm con-
trol valve. (fig. 17-5)
3. Attach the 0-1000psi hydraulic gauge to test port

(B) on the top of the valve. Route the gauge so
that you or an assistant can read the gauge while
performing the test procedures. (figure 17-5, 17-6)
17-6
4. Start the machine and with the auxiliary hydraulic
switch off (no functions activated) and the engine
at idle, you should read 218 psi at test port (B).
5. Attach the 0-6000psi gauge to test port B, then

activate the low or high flow auxiliary hydraulics High Pressure
with no auxiliary attachment fastened to the quick
couplers. This action will send oil over relief and
you will read the actual pressures required to acti-
vate the relief valve for each circuit. Do this for
both the high and low flow circuits in both direc-
tions. Record the pressure readings. Standby
17-7
Check your readings against those stated below. If
your readings differ, an adjustment and or repair may
be required.
Pressures should read: (at test port B)

• 218 +/- 10 PSI with system relaxed (standby).
• 3000 +/- 100 PSI with Low Flow activated.
• 3000 +/- 100 PSI with High Flow activated.
6. If necessary, adjust the relief settings on the auxil-

iary standby or high pressure valves. (figure 17-7)
To adjust:
a) Remove the cap covering the affected relief
valve.
b) Using an allen wrench, turn the adjustment

screw clockwise to increase the setting or
counter-clock wise to reduce it until within
specification.
17-3
Rubber Track Loader
Lift Arm Pressure Check Drive Pressure Check

Pressure Gauge 0-6000 p.s.i. Pressure Gauge 0-6000 p.s.i.
Lift arm pressure is used to lift loads or “break-out”.
Low lift arm pressure can produce a weak lift arm func- !WARNING!
tion while high lift arm pressure can damage lift arm This procedure should only be performed if you suspect
and hydraulic components. a drive pump or drive motor is faulty. The procedure is
difficult and in performing it, you risk contaminating
Note: Make sure auxiliary circuit pressures are set correctly your hydraulic system if your equipment and working
prior to testing this function. environment is not clean.
1. Attach a hydraulic gauge to test port B. Route the Make certain all couplers, fittings and hoses used during
gauge so that you or an assistant can read the this process are clean and free of contaminants that may
gauge while testing these functions. (figure 17-6) potentially cause damage to the hydraulic pump and or
system components!
2. Raise the lift arms all the way up and continue
holding the joystick even when the lift arms stop. Drive pressure is used to turn the drive motors that
Record the pressure readings. Then lower the lift power your tracks. Low pressure can cause decreased
arms to the stops and continue holding the joy- drive motor performance resulting in sluggish maneu-
stick. Record the pressure readings. Repeat this vering, decreased speed and or uneven forward or
process with the bucket dump/curl functions. reverse motion.
3. Check your readings against those stated below. If 1. Remove the plug from the port you would like to
your readings differ, adjustment or repair may be test and insert a quick coupler similar to the one in
necessary. (figure 17-8) port A or B.
Note: There are 4 drive pump test ports. The left side ports
Pressures should read: (at test port B) are shown in figure 17-10 and the right side ports are located
• 3000 +/- 100 PSI when the lift arms or bucket are to the right of the drive ports they test.
in the up/curl position.
• 3000 +/- 100 PSI when the lift arms or bucket are 2. Attach the hydraulic gauge to the port(s) you are
in the down/dump position. trying to test and route the gauge so you or an
assistant can read the gauge during testing.
4. If any of the readings are low, reverse the function
and recheck. If reading is within specification in 3. Position the machine so that the lift arms are rest-
that direction, replace the opposing relief valve. ing against the chassis stops and the front edge of
the bucket is facing, centered on and in contact
Relief Valves with an IMMOVABLE object.
4. Move the drive control fully forward in an attempt

Port (B) to drive the machine forward. This will force oil
over the relief valve and give you a reading for the
circuit you are tapped into.
5. Attach a heavy-duty chain capable of restraining

the machine securely to the bucket and an
IMMOVABLE object.
6. Move the drive control fully rearward in an attempt

to drive the machine in reverse. This will force oil
over the relief valve and give you a reading for the
circuit you are tapped into.
17-8 Relief Valves
7. Check all four ports in this same manner and
record your readings.
17-4
Rubber Track Loader
Check your readings against that stated below. If your Posi-Power Pressure Check
readings differ, relief replacement and or component Posi-power is a function of the tandem drive pump
repair may be required. assembly. The posi-power control reads charge flow
(which is directly related to engine rpm) and adjusts
Pressures should read: drive pump flow to maximize torque and prevent
• 5500 PSI when the relief is reached in attempted engine stall during high load conditions.
forward or reverse motion.
Drive pressure troubleshooting: !WARNING!

8. If one reading is low, swap the relief valve with a This procedure should only be performed if you
similar one and recheck. If the reading improves, suspect that the Posi-Power relief valve is faulty. In
replace the faulty relief valve. performing this procedure you risk contaminating
your hydraulic system if your equipment and work-
9. If two readings are low, but on different circuits ing environment is not clean.
(pumps), perform step 8 for both.
Make certain all couplers, fittings and hoses used
10. If both readings are low on one pump, disconnect during this process are clean and free of contami-
the drive hoses from the suspected ports and plug nants that may potentially cause damage to the
them at the pump. Cap the hoses to prevent con- hydraulic pump and or system components!
tamination and then recheck the pressures at
those ports. If the reading improves, the drive
motor is at fault. If the reading does not improve,
one pump (in the tandem assembly) is at fault.
11. If all 4 readings are low, it is unlikely that all four

relief valves are faulty. The tandem pumps are
most likely not working properly. Posi-Power
Adjustment
Relief Valves Posi-Power

Outlet
17-11
To check Posi-Power pressure:

1. With the engine off and cool, disconnect and cap
17-9 the posi-power outlet hose from the port on the top
of the drive pump assembly. (figure 17-11)
2. Remove the fitting from the pump assembly and

Test Ports install a quick coupler similar to the one installed in
(see note) test port A or B in its place.
3. Attach a gauge to the quick coupler and route it so

that you or an assistant can read the gauge during
operation.
4. Make sure all bystanders are clear of moving parts

17-10 and start the engine.
5. At low rpm, posi-power pressure should read 180

+/- 40 psi. (475 +/- 40 at high rpm)
17-5
Rubber Track Loader
6. If your reading is low, remove the cap and loosen Auxiliary Flow Test
the jam nut on the posi-power adjustment screw The PT-70 and PT-80 are equipped with both high and
and turn it counter clockwise until it stops then low flow auxiliary circuits. If an auxiliary flow problem is
retighten the jam nut. (figure 17-11) suspected, the following procedures should be per-
formed.
a) If the screw was already turned completely
out and pressure reads lower than specified, Note: If an auxiliary circuit problem is suspected, per-
the posi-power relief valve is faulty and should form all pressure test and adjustment procedures as
be replaced. necessary prior to attempting the perform the flow test
procedure. Most issues will be solved with the pres-
b) If you were able to turn the screw out, recheck sure test and adjustment procedures, but if a problem
posi-power pressure to see if the reading is still persists after all pressures are correctly set, pro-
now within specification. If it is, the system ceed with the flow test.
should function properly. If it did not improve,
the posi-power relief valve is faulty and should Required Tools
be replaced.
Flow Meter (with variable loading valve)
To Adjust Posi-Power: L o w F lo w A u xilia
1. Loosen the jam nut and then turn the screw to
adjust for more or less posi-power function. 25
(figure 17 -11) 20
20
19
18
17
a) Turn the screw clockwise to increase function 15
and limit pump flow during high load condi- 10

tions. (less likely to stall)
5
0
b) Turn counter-clockwise to decrease function 0
and maximize pump flow during high load con- 0 psi 1000 psi 2000 psi 2500 psi 3000 psi
S ystem Loa
ditions. (more likely to stall)
2. Tighten the jam nut while holding the set screw in H ig h F lo w A u xilia
place to keep desired setting.

35 31 31 30
30
26
25
20
15
10
5
0
0
0 psi 1000 psi 2000 psi 2500 psi 3000 psi
S ystem Loa
Note: The charts above give the acceptable ranges for

fluid flow when loaded to the levels indicated. The low
flow values are to be understood as acceptable if with-
in 1 gpm of the specified value. The high flow values
are acceptable if within 2 gpm of the specified value.
To test flow:
1. Attach a flow meter to the quick couplers of the cir-
cuit to be tested. (high or low flow)
2. Start the machine and activate the circuit.
3. Record and compare your readings with those of

the charts above in both directions.
17-6
Rubber Track Loader
Flow Troubleshooting Problem 6:

If your readings differ from those listed on the charts, High and low flow functions only work in one
identify the symptom you are experiencing in the list of direction.
possible problems below and follow the steps to identi- Possible causes:
fy and correct the problem. 1. Wire broken or disconnected at the pilot generation
block.
Problem 1: 2. Solenoid coil malfunction. (see page 3-5)
Both high and low flow readings are less than 3. Solenoid spool malfunction. (see page 3-5)
specified. 4. Faulty auxiliary hydraulic switch.
Possible causes:
1. Auxiliary relief valve pressure setting incorrectly Problem 7:
(see page 17-3) Low flow works as intended when using the con-
2. Quick coupler block pressure release valve stuck in tinuous switch, but does not work when using the
down (release) position. variable flow thumb switch.
3. Auxiliary pump malfunctioning or faulty. Possible causes:
4. Engine RPM too low. 1. Variable flow fuse blown.
2. Power wire to variable flow switch broken or dis-
Problem 2: connected. (BU-16 see electrical schematic)
High flow readings are less than specified (low 3. Variable flow switch malfunction.
flow is within specification). 4. If the switch works in one direction, but not the
Possible causes: other, check the pressure reducing proportional
1. Low charge pressure. valves and the wires that connect them to the
2. Control valve spool malfunction. wiring harness for proper condition and function.
(see page 3-5, view B item 6, view D item 4)
Note: Make sure that the high flow reading is greater
than the low flow reading. If they are equal, the prob-
lem is most likely electrical.
Problem 3:
Flow is within specifications in one direction, but
lower than specified in the other.
Possible causes:
1. Auxiliary line relief valve in need of replacement.
(see page 17-4 for test instructions and figure 17-8
for location)
2. Control valve spool malfunction.
Problem 4:
Low flow readings are less than specified (high
flow is within specification).
To correct:
1. Turn the adjustment screw on the pilot generation
block pressure reducing valve clockwise to increase
the flow within the low flow circuit until correct.
(see page 3-5, view D, item 5 to locate)
Problem 5:
Low flow readings are higher than specified (High
flow is within specification).
To correct:
1. Turn the adjustment screw on the pilot generation
block pressure reducing valve counter clockwise to
decrease the flow within the low flow circuit until
correct. (see page 3-5, view D, item 5 to locate)
17-7
17-8
18. Troubleshooting
Chapter Overview Visual Inspection

This chapter contains basic troubleshooting proce- Prior to troubleshooting, walk around the machine and
dures for the PT-70 and PT-80 Rubber Track Loaders. perform an overall visual inspection. Look for missing,
loose, worn or broken parts. Pay particular attention to
Additional troubleshooting aids are provided in Chapter the following items:
3 (Circuit Diagrams) and in chapters containing disas-
sembly and assembly procedures for the appropriate • Track tension
component or assembly. • Fluid levels
• Fan belt tension and condition
Personal Safety • Hoses (no visible sign of wear)
• Fittings (no apparent leaks)
!WARNING! • Battery cables
Improper or incomplete maintenance/repair of a Rubber • Fuse panel (fuses in place and operational)
Track Loader can be dangerous and may result in • Controls (for neutral)
A simple visual inspection and operational check can
Do not attempt to perform any type of repair or mainte- identify many problems without the need for extensive
nance on a Rubber Track Loader until you have read and troubleshooting. However, if these checks indicate a
problem that requires further analysis, proceed to
Refer to the Operation and Maintenance manual for Troubleshooting.
niques before operating any Rubber Track Loader. General Troubleshooting
The most effective way to prevent a malfunction from
Prior to performing any type of service work on a occurring is to closely follow the recommended mainte-
Rubber Track Loader, read and understand Chapter 1 nance schedule and instructions throughout the life of
(Product Safety) for personal safety information. the machine. However, if a malfunction does occur,
finding the problem and fixing it quickly are important.
This section covers a select set of symptoms that may
occur and suggests possible causes.
Problem 1:
Machine will not crank over.
Possible causes
1. Continuous high flow switch activated.
2. Continuous low flow switch activated.
3. Power quick-attach switch in unlocked position. (if
equipped)
4. Battery cables loose or corroded.
5. Ignition fuse blown.
6. Main starter fuse blown.
7. Starter relay malfunctioning.
8. Weak or dead battery.
9. Faulty continuous hydraulic flow switch.
10.Faulty power quick attach switch.
11. Faulty ignition switch.
12.Faulty starter.
13.Loose, broken or disconnected wiring at key, relay
or starter.
14.Main power fuse (60-80 amp) blown.
18-1
Rubber Track Loader
18. Troubleshooting
Problem 2: Problem 5:
Machine cranks, but will not start. Tracks are operational, but lift arms will not move.
Possible causes Possible causes
1. Fuel tank empty, fuel filter plugged or fuel line 1. Continuous hydraulic flow switch activated, sending
restricted. oil over relief. (lift arms work, but move slowly)
2. Battery discharged (engine rotates slowly). If auxiliary flow hydraulics work check for:
3. Injection pump fuse blown. a) Leak in feed line to lift arm control joystick (pilot
4. Power relay (B) fuse blown (40 amp). control).
5. Faulty power relay (B). b) Lift arm control joystick (pilot control) malfunc
6. Loose, broken or disconnected wiring at injection tion.
pump, fuel pump or fuse. c) Lift arm control valve assembly malfunction.
7. Glow plugs not pre-heating (look for black smoke). If auxiliary flow hydraulics do not work check for:
a) Main glow plug fuse blown. a) Main auxiliary relief malfunction.
b) Glow plug relay malfunctioning. b) Faulty auxiliary pump.
c) Loose, broken, or disconnected wiring at ignition
switch, relay or glow plug ground strip. Problem 6:
d) Faulty glow plugs. Lift arms are operational, but high/low flow auxil-
8. Faulty ignition switch. iary circuits are not.
9. Loose, broken or disconnected wiring in starting cir- Possible causes
cuit. 1. Auxiliary hydraulic fuse blown.
10.Loose, broken or disconnected wiring at fuel shutoff 2. Faulty ground in at chassis crossmember.
solenoid. 3. Faulty auxiliary hydraulic switch.
11. Air in fuel system or defective fuel injection pump. 4. Faulty auxiliary hydraulic solenoid at pilot genera-
tion block.
Problem 3: 5. Loose, broken or disconnected wire at fuse, auxil-
Machine starts, but hydraulics will not operate. iary hydraulic switch, pin connector P10.
Possible causes 6. Auxiliary hydraulic pilot generation spool stuck in
1. Operator not in seat. closed position.
2. Seat belt not fastened. 7. Faulty or improperly connected quick coupler.
3. Safety relay fuse and or or safety solenoid fuse for 8. Quick coupler block pressure release stuck in down
seat belt or operator presence safety switches (open) position.
blown.
4. Faulty operator presence safety switch. Problem 7:
a) Test for continuity through operator presence Multiple switches/electrical accessories are not
and seat belt switches. Adjust or replace as neces- operational in ON or RUN position.
sary. Possible causes
5. Loose, broken or disconnected ground wires (check 1. Power A or B fuse blown.
ground connections behind the operator seat, from 2. Faulty power relay (A or B).
cab to chassis and on the chassis crossmember.) 3. Faulty ignition switch.
6. Faulty safety relay. 4. Loose, broken or disconnected wiring at ignition
7. Faulty safety solenoid or safety solenoid spool. switch, fuse or relay.
8. Loose, broken or disconnected wiring at fuse, relay,
or safety solenoid. Problem 8:
9. Low charge pressure. Battery will not charge/maintain charge.
Possible causes:
Problem 4: 1. Loose alternator belt.
Lift arm/bucket controls are operational, but tracks 2. Alternator fuse blown.
will not move. 3. Faulty alternator diode.
Possible causes 4. Loose, broken or disconnected wiring at battery,
1. Leak in feed line to drive control joystick (pilot con- alternator, diode or fuse.
trol). 5. Excessive current draw with key in "off" position.
2. Loose, broken or disconnected wire to DA control 6. Faulty battery.
solenoid. 7. Faulty alternator.
3. Drive control joystick (pilot control) malfunction.
4. Low charge pressure.
5. Parking brake switch in on position.
6. Faulty parking brake switch.
18-2
Rubber Track Loader
18. Troubleshooting
Problem 9: Engine/Machine Troubleshooting

Lift arm control joystick will not lock into float When a problem occurs that effects engine perform-
position. ance or function, it is important to determine whether
Possible causes or not the problem lies with the machine itself, or with
1. Float magnet fuse blown. the engine. A machine problem should be repaired by
2. Loose, broken, or disconnected wiring at fuse, float an ASV dealer, while an engine specific problem
detent magnet, or pin connector P8. should only be repaired by a representative of the
3. Faulty float detent magnet. engine manufacturer. Making this determination will
ensure timely and appropriate service to help minimize
Problem 10: down-time.
Lift arms will not float, engine labors and lift arms
create down pressure when float is engaged. Problem:
Possible causes Hard starting
1. Engine RPM too low. check for:
2. Low charge pressure. 1. 12V power to glow plugs. (With test light or multi-
3. Lift arm control joystick malfunction (pilot control). meter, measure voltage at green glow plug com-
4. Lift arm control valve malfunctioning. mon power lead.)
a) If power is not present, see problem 1, step 7.
Problem 11: 2. Water in fuel.
Hydraulic oil temperature elevated; hydraulic sys- 3. Proper grade and quality fuel.
tem overheating.
Possible causes Problem:
1. Debris plugging oil cooler, limiting airflow. Low power
2. Low hydraulic oil level. check for:
3. Loose or missing fan belt. 1. Dirty, clogged, or restricted fuel filter.
4. Damaged or missing cooling fan blades. 2. Adequate supply of fuel to engine (fuel lines).
5. Incompatible attachment. 3. Water in fuel.
a) Attachment must match machine flow capabili 4. Proper grade and quality fuel.
ties.
b) Attachment hose inside diameter must be at Problem:
least ½" for low flow and ¾" for high flow. No start
c) Low flow attachment coupled to high flow circuit. check for:
6. Faulty hydraulic oil temperature sending unit. 1. 12V power at fuel shutoff solenoid. (With test light
7. Faulty quick coupler. or multi-meter, measure voltage at white power
8. Cooler bypass relief open. lead entering the solenoid.)
a) If no power is present, see problem 1, step 3-6)
Note: Cooler bypass should open at 80 PSI. 2. Ensure 12V power to fuel pump. (With test light or
multi-meter, measure voltage at white power lead
Problem 12: entering the electronic fuel pump.)
Engine coolant temperature elevated; engine over- 3. Low fuel.
heating. 4. Out of fuel. (ensure proper gauge/sending unit
Possible causes: function. Inspect tank for fuel)
1. Low coolant level. 5. Blocked or restricted fuel line. (try alternate/remote
2. Debris plugging radiator, limiting airflow. fuel supply to pump.)
3. Damaged or missing cooling fan blades. 6. Water in fuel.
4. Loose or missing fan belt. 7. Proper grade and quality fuel.
5. Faulty engine coolant temperature gauge.
If any of the above conditions are present, the problem
lies with the machine and should be serviced by an
ASV dealer. If the conditions listed above are not pres-
ent, the problem lies with the engine and it should be
serviced by a Perkins engine repair facility to comply
with the conditions of the engine warranty.
18-3
18-4
19. Lubricant & Fuel
Specifications
Chapter Overview Fuel Specifications

When replacing or replenishing the fluids and lubri- In North America, diesel fuel, distilled from crude oil,
cants in an ASV Rubber Track Loader, use ASV prod- identified as No. 1-D or No. 2-D in “ASTM D975” gen-
ucts. This ensures that the new fluids and lubricants erally meet machine requirements.
match those originally installed when the machine left
the ASV factory. ASV products were developed for,
tested and approved by ASV to assure optimum life
and performance in all ASV Rubber Track Equipment,
when used as recommended.
Fluids
Engine Oil
• ASV Heavy Duty Engine Oil, 10W-30
Capacity: 9 U.S. quarts (including filter)
P/N: 0300-767 1 quart
P/N: 0402-838 12 quarts
P/N: 0402-839 1 gallon
P/N: 0402-840 6 gallons
Engine Anti-freeze/Coolant
• ASV Long-Life 50/50 Antifreeze/Coolant
Capacity: 3.125 U.S. gallons
P/N: 0300-766 1 gallon
P/N: 0402-841 6 gallons
Hydraulic Oil
• ASV Premium All Season MV Hydraulic Oil
Capacity: 20 U.S. gallons (including filters)
P/N: 0400-253 5 gallons
P/N: 0402-833 55 gallons
Grease (general-use)
• ASV Multi-Purpose EP Lithium Grease
P/N: 0300-769 1 tube
P/N: 0402-844 10 tubes
P/N: 0402-834 40 tubes
If ASV products are not available, use high quality sub-

stitutions that meet or exceed factory installed fluid
specifications.
19-1
19-2
20. Service Aids &
Supplements
General Torque Specifications
Inch Fasteners Metric Fasteners

Thread Size Standard Torque Thread Size Standard Torque
1/4" 9 +/- 2 lb ft M6 12 +/- 3 Nm
5/16" 18 +/- 4 lb ft M8 28 +/- 7 Nm
3/8" 35 +/- 7lb ft M10 55 +/- 10 Nm
7/16" 50 +/- 11 lb ft M12 100 +/- 20 Nm
1/2" 75 +/- 15 lb ft M14 160 +/- 30 Nm
9/16" 120 +/- 22 lb ft M16 240 +/- 40 Nm
5/8" 160 +/- 30 lb ft M20 460 +/- 60 Nm
3/4" 275 +/- 37 lb ft M24 800 +/- 100 Nm
7/8" 460 +/- 60 lb ft M30 1600 +/- 200 Nm
1" 660 +/- 75 lb ft M36 2700 +/- 300 Nm
1-1/8" 960 +/- 110 lb ft
1-1/4" 1320 +/- 150 lb ft
1-3/8" 1780 +/- 220 lb ft
1-1/2" 2280 +/- 260 lb ft
20-1
Terex Construction Americas
8800 Rostin Road
Southaven, MS 38671
(888)-201-6008
(662)-393-1800
www.terex.com

PT 70 80 Service Manual 1 08

Uploaded by

Copyright:

Available Formats

PT 70 80 Service Manual 1 08

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PT 70 80 Service Manual 1 08

Uploaded by

Copyright:

Available Formats

Service Manual

1. Product Safety 3. Circuit Diagrams

6. Operator Enclosure Machine Preparation . . . . . . . . . . . . . . . . . . . 8-1

12. Engine 16. Hydraulic Component Service

15. Quick Attach 19. Lubricant and Fuel Specifications

Note: This label is used to provide important additional infor-

!CAUTION! Refer to the Operation and Maintenance manual for

Protective Equipment Batteries

Repair cause bodily injury, death or property damage. Be

If dust that may contain asbestos is present, there are

1. Never use compressed air for cleaning. Avoid

3. Wear an approved respirator if there is no other

4. Comply with applicable rules and regulations for

5. Obey environmental regulations for disposal of

Machine Label and Decal Examples

With the engine off Engine Warm-Up

WARNING Keep away from tracks while machine is in motion.

PT-80 Specifications Oil Cooler

Lift Arm Control Valve

PT-70 Specifications Oil Cooler

Lift Arm Control Valve

Chapter Overview Hydraulic Charge Circuit

Figure 3-1 PT-70/80 Hydraulic Charge Circuit

PILOT GEN BLOCK TANK

Hydraulic Auxiliary Circuit

Figure 3-2 PT-70/80 Hydraulic Auxiliary Circuit

TO BUCKET CYL. FLOW

TO LIFT ARM CYL.

LIFT ARM VALVE

CHARGE PUMP INLET

PILOT GEN. BLOCK AUXILIARY PUMP INLET

Hydraulic Drive Circuit

Figure 3-3 PT-70/80 Hydraulic Drive Circuit

DRIVE MOTOR DRIVE PUMP

2-SPEED SHIFT (PT-80)

Lift Arm Control Valve

Figure 3-4 PT-70/80 Lift Arm Control Valve

RELIEF VALVE SETTINGS

(B3) 3307 PSI (A3) 3307 PSI

(B2) 3147 PSI (A2) 3669 PSI

(B1) 3640 PSI (A1) Anti-Cavitation

Hydraulic Pilot Generation

Figure 3-5 PT-70/80 Hyd. Pilot Generation Block

Electrical Attachment Outlet

Figure 3-6 PT-70/80 Electrical Attachment Outlet

Figure 3-7 PT-70/80 Standard Drive Control

Lift Arm Control

Chapter Overview Lift Arm Brace

To remove the lift arm brace:

Grease Fitting Locations

Track Tension (PT-70/80)

B New Roller Normal Wear

4. Remove the external snap ring (H) from the bear

Note: The PT-80 style undercarriage is depicted in this

Note: A shop vac or pressure washer will work well to

2. Clean the threads on the turnbuckle thoroughly

6. Remove the outer scraper plate from the suspen

9. Once the track is in position over the idler wheels,

Note: The secondary element is not serviceable. It