88 INSIDE DENTISTRY—OCTOBER 2007

LAB Laboratory perspectives from the inside out.

taLk
Creating Physiologic Contours Using a
Modified Geller Cast Technique
Edward A. McLaren, DDS; and Yi-Yuan Chang, MDC
Edward A. McLaren, DDS
For a restoration to be successful clin- Controlling the contours of final restor- visualize the relationship of the free gin- Director
ically it needs to satisfy several criteria: ations begins with pre-planning before gival margin to the cervical contours of Center for Esthetic Dentistry
ever picking up a handpiece and bur. Fi- the restoration. Both work, but with slight
•mechanical/structural requirements nal 3-dimensional tooth positioning, the difficulties. The solid cast does not use the Founder and Director
(ie, durability) of both the tooth and type of restoration, and the desired color actual dies, which makes them impossible UCLA Master Dental Ceramist Program
the restoration; change from the existing clinical situa- to use in a foil or refractory technique. The
• esthetic requirements of position, form, tion dictate tooth structure removal and only way to use this technique is after the Adjunct Associate Professor
and color; and were discussed in the two previous arti- dies are divested or removed from the foil; UCLA School of Dentistry
• biologic requirements of pulpal health, cles in this series.1,2 This article will dis- they then must be “fit” to the solid cast. If Los Angeles, California
prevention of caries, and gingival health. cuss how to control the gingival contours there are problems with contour or fit it is
of the final restorations in the laboratory. very difficult to correct. The “soft tissue Private Practice limited to Prosthodontics and
One of the crucial aspects of successful Ideally, the ceramist should work on a cast” technique allows the use of the mas- Esthetic Dentistry
esthetic restorative dentistry is controlling master cast that has the gingival elements ter dies, but the authors and many of their
gingival contours. Physiologic contours intact (ie, not trimmed away). Many tech- colleagues express dislike for using this
or emergence profiles are important for niques have been discussed, from using a material with veneers or anterior crowns
gingival health, as overcontoured restor- solid untrimmed cast (Figure 2) to using because this material is very difficult to ad-
ations can lead to gingival inflammation casts that use pink flexible silicone mate- just. This article will discuss the authors’
(Figure 1). rials (Figure 3) that allow the ceramist to modified Geller cast technique that allows

Yi-Yuan Chang, MDC

Master Dental Ceramist
Full Time Faculty
UCLA Master Dental Ceramist
Residency Program
Figure 1 Image of a clinical situation of overcon- Figure 2 Image of a solid cast without remov- Figure 3 A soft tissue cast with removable dies us- UCLA School of Dentistry
tour with the associated gingival inflammation. able dies. ing the pink PVS impression material for the gingiva. Los Angeles, California

Figure 4 Elastomeric impression with excellent Figure 5 The marginal gingiva is blocked out Figure 6 Sectional first pour of the master Figure 7 The sectioned dies.
marginal detail. with wax to support this area so that it does not dies upon removal from impression.
tear on stone removal.

Figure 8 Facial view of trimmed die. Figure 9 Sagittal view of trimmed die; note Figure 10 The margins are marked, and the Figure 11 The dies are placed in a
that the palatal gingival area is not trimmed away. dies are sealed and ready for duplication. duplicating ring.
INSIDE DENTISTRY—OCTOBER 2007 89

Figure 12 A low-viscosity PVS-duplicating Figure 13 The duplicated master die after Figure 14 The dies are placed back in the Figure 15 The master cast after it has been
material is poured into the duplicating ring. pouring in die stone and placing one coat of die impression and the die lube/separator is placed poured with die stone.
spacer on the neck or tapered area of the dies. on the dies.

removable dies and interchangeable re-

fractory dies, and maintains the soft tis-
sue elements in die stone.

TECHNIQUE
Final impressions should be generated
with an elastomeric impression material
that allows multiple pours, eg, Impregum™
Garant™ Soft Light Body Impression
Material by 3M ESPE (St. Paul, MN)
(Figure 4). At least two pours of the im-
pression will need to be made. When
pouring impressions multiple times,
sometimes the marginal area of the im-
pression will tear because of the thin-
ness of the impression material in this
area. To avoid this, sticky wax can be
built up to fill in where the free gingival
margin is; this supports or blocks out
the thin area of impression material that
went subgingival during the impression
process (Figure 5). This will allow mul-
tiple pours without tearing. The authors
make two master-die pours in this fash-
ion (Figure 6). The dies should be sec-
tioned (Figure 7) and then trimmed and
tapered so that there are no undercuts
(Figure 8). For veneers, the lingual soft
tissue should not be cut away; this helps
stabilize the die in the cast and acts as
an anti-rotation or seating device (Fig-
ure 9). The margins are marked with a
red pencil and the dies are sealed (Fig-
ure 10). The master dies are then mount-
ed on a duplicating device (Figure 11).
A low-viscosity polyvinyl siloxane
(PVS) duplicating material should be
poured into the ring around the dies
(Figure 12).
Next, the duplicated master dies can be
die-spaced with one coat of die spacer on
the part of the die that is subgingival (Fig-
ure 13). It has been found by the authors

ONE OF THE
CRUCIAL ASPECTS
OF SUCCESSFUL
ESTHETIC
RESTORATIVE
DENTISTRY IS
CONTROLLING
GINGIVAL CONTOURS.
(Circle 85 on Reader Service Card)
90 INSIDE DENTISTRY—OCTOBER 2007

TO CREATE INTERCHANGEABLE REFRACTORY DIES FOR

THE MASTER CAST, THE ORIGINAL MASTER DIES ARE
DUPLICATED, BUT SHOULD NOT BE OTHERWISE USED
UP TO THIS POINT. THESE DIES SHOULD BE SPACED
WITH THE APPROPRIATE AMOUNT OF DIE SPACER ON
Figure 16 Demonstration of the resolvability
of the dies with the intact gingival elements. THE PREPARATION AREA JUST SHORT OF THE MARGIN.

that one coat of die spacer is necessary to

compensate for the slight expansion of the
refractory die. This die should be sealed,
the die separator placed on it, and the
dies placed back in the master impres-
sion (no wax is used at this point in the

Figure 17 The original master die (the one

that was previously duplicated) is die-spaced in
the region to receive the restoration.

Figure 18 The die-spaced dies are placed

back in the duplicating ring and poured with PVS
duplicating material as before.

Figure 19 The refractory die generated from

duplicating the die-spaced master die.

Figure 20 The master cast with the sealed refrac-

tory dies in place, ready for porcelain application.
INSIDE DENTISTRY—OCTOBER 2007 91

impression so as to reproduce all of the ring and duplicated as before (Figure material that is specific to the porcelain erative condition, conservative prepara-
gingival contours in stone) (Figure 14). 18). Note that these dies had no die spacer used (Figure 19). The dies will fit back in the tions, and the final esthetic outcome of
Die stone is then poured into the full im- on the neck or root of the die. The dies that master cast and will be interchangeable veneers placed on teeth Nos. 6 through 11.
pression around the dies that have been were used in the master cast have one coat with the duplicate master dies (Figure 20).
lubricated. The master cast with fully in- of die space on the neck or root to make the The refractory dies should be sealed with REFERENCES
tact gingiva and removable dies is demon- socket or hole the die fits in slightly larg- a material that is specific to the porcelain 1. McLaren EA, Bazos, M. Controlling tooth
strated in Figure 15 and Figure 16. It can er than the die. This allows for the slight system. The porcelain is built up similar- reduction and the bonded mock-up: Part I.
be seen at this point how much easier it expansion of the refractory material and ly to other techniques, but as seen in Figure Inside Dentistry. 2007;3(2):96-100.
would be to visualize correct gingival con- allows the refractory die to seat in the mas- 21, because of the stone replication of the 2. McLaren EA, Vigoren G. Preparations and
tours than with a conventional pinned- ter cast properly. Once the master die with gingival, it is much easier to create es- controlling tooth reduction Part 2: Crowns
die technique. die spacer only on the preparation area is thetic and physiologic contours. Figure and fixed partial dentures. Inside Dentistry.
To create interchangeable refractory duplicated, it is poured with a refractory 22 through Figure 24 represent the preop- 2007;3(5):86-90.
dies for the master cast, the original mas-
ter dies are duplicated, but should not be
otherwise used up to this point. These
dies should be spaced with the appropri-
ate amount of die spacer on the prepara-
tion area just short of the margin (Figure
17). The dies can be placed in a duplicating

Figure 21 Using the modified Geller cast dur-

ing the porcelain application process.

Figure 22 Preoperative condition of the

patient used to demonstrate this technique.

Figure 23 Conservative porcelain veneer

preparations.

Figure 24 The final esthetic outcome of porce-

lain veneers placed on teeth Nos. 6 through 11.

(Circle 90 on Reader Service Card)