Deciphering Weld Symbols

When welds are specified on engineering and fabrication drawings, a cryptic set of symbols is used as a sort of
shorthand for describing the type of weld, its size, and other processing and finishing information. The purpose of
this page is to introduce you to the common symbols and their meaning. The complete set of symbols is given in a
standard published by the American National Standards Institute and the American Welding Society:

ANSI/AWS A2.4, Symbols for Welding and Nondestructive Testing.

Our thanks to Dr. Kent L. Johnson, past Chairman of the AWS Chicago Section, for his many helpful comments
on the content of our welding pages.

The structure of the welding symbol

The horizontal line--called the reference line--is the anchor to which all the other welding symbols are tied. The
instructions for making the weld are strung along the reference line. An arrow connects the reference line to the
joint that is to be welded. In the example above, the arrow is shown growing out of the right end of the reference
line and heading down and to the right, but many other combinations are allowed.

Quite often, there are two sides to the joint to which the arrow points, and therefore two potential places for a
weld. For example, when two steel plates are joined together into a T shape, welding may be done on either side
of the stem of the T.

The weld symbol distinguishes between the two sides of a joint by using the arrow and the spaces above and
below the reference line. The side of the joint to which the arrow points is known (rather prosaically) as the arrow
side, and its weld is made according to the instructions given below the reference line. The other side of the joint
is known (even more prosaically) as the other side, and its weld is made according to the instructions given above
the reference line. The below=arrow and above=other rules apply regardless of the arrow's direction.

The flag growing out of the junction of the reference line and the arrow is present if the weld is to be made in the
1
field during erection of the structure. A weld symbol without a flag indicates that the weld is to be made in the
shop. In older drawings, a field weld may be denoted by a filled black circle at the junction between the arrow and
the reference line.

The open circle at the arrow/reference line junction is present if the weld is to go all around the joint, as in the
example below.

The tail of the weld symbol is the place for supplementary information on the weld. It may contain a reference to
the welding process, the electrode, a detail drawing, any information that aids in the making of the weld that does
not have its own special place on the symbol.

Types of welds and their symbols

Fillet welds Groove welds Plug welds and slot welds

WELDING SYMBOLS

Special symbols are used on a drawing to specify where welds are to be located, the type of joint to be
used, as well as the size and amount of weld metal to be deposited in the joint. These symbols have
been standardized by the American Welding Society (AWS). You will come into contact with these
symbols anytime you do a welding job from a set of blueprints. You need to have a working
knowledge of the basic weld symbols and the standard location of all the elements of a welding
symbol.
2
A standard welding symbol (fig. 3-43) consists of a reference line, an arrow, and a tail. The reference
line becomes the foundation of the welding symbol. It is used to apply weld symbols, dimensions, and
other data to the weld. The arrow simply connects the reference line to the joint or area to be welded.
The direction of the arrow has no bearing on the significance of the reference line. The tail of the
welding symbol is used only when necessary to include a specification, process, or other reference
information.

Weld Symbols

The term weld symbol refers to the symbol for a specific type of weld. As discussed earlier, fillet,
groove, surfacing, plug, and slot are all types of welds. Basic weld symbols are shown in figure 3-44.
The weld

Figure 3-44.-Basic weld symbols.

Figure 3-45.-Weld symbols applied to reference line.

3
Figure 3-46.-Specifying weld locations.

Figure 3-47.-Arrowhead indicates beveled plate.

symbol is only part of the information required in the welding symbol. The term welding symbol
refers to the total symbol, which includes all information needed to specify the weld(s) required.

Figure 3-45 shows how a weld symbol is applied to the reference line. Notice that the vertical leg of
the weld symbol is shown drawn to the left of the slanted leg. Regardless of whether the symbol is for
a fillet, bevel, J-groove, or flare-bevel weld, the vertical leg is always drawn to the left.

Figure 3-46 shows the significance of the positions of the weld symbols position on the reference line.
In view A the weld symbol is on the lower side of the reference line that is termed the arrow side.
View B shows a weld symbol on the upper side of the reference line that is termed the other side.
When weld symbols are placed on both sides of the reference line, welds must be made on both sides
of the joint (view C).

4
When only one edge of a joint is to be beveled, it is necessary to show which member is to be beveled.
When such a joint is specified, the arrow of the welding symbol points with a definite break toward
the member to be beveled. This is shown in figure 3-47.

Figure 3-48 shows other elements that may be added to a welding symbol. The information applied to
the reference line on a welding symbol is read from left to right regardless of the direction of the
arrow.

Dimensioning

In figure 3-48, notice there are designated locations for the size, length, pitch (center-to-center
spacing), groove angle, and root opening of a weld. These locations are determined by the side of the
reference line on which the weld symbol is placed. Figure 3-49 shows how dimensions are applied to
symbols.

Figure 3-48.-Elements of a welding symbol.

5
Figure 3-49.-Dimensions applied to weld symbols.

Figure 3-50.-Dimensioning of welds.

6
Figure 3-51.-Supplementary symbols.

Figure 3-50 shows the meaning of various welding dimension symbols. Notice that the size of a weld
is shown on the left side of the weld symbol (fig. 3-50, view A). The length and pitch of a fillet weld
are indicated on the right side of the weld symbol. View B shows a tee joint with 2-inch intermittent
fillet welds that are 5 inches apart, on center. The size of a groove weld is shown in view C. Both sides
are 1/2 inch, but note that the 60-degree groove is on the other side of the joint and the 45-degree
groove is on the arrow side.

Supplementary Symbols

In addition to basic weld symbols, a set of supplementary symbols may be added to a welding symbol.
Some of the most common supplementary symbols are shown in figure 3-51.

Contour symbols are used with weld symbols to show how the face of the weld is to be formed. In
addition to contour symbols, finish symbols are used to indicate the method to use for forming the
contour of the weld.

When a finish symbol is used, it shows the method of finish, not the degree of finish; for example, a C
is used to indicate finish by chipping, an M means machining, and a G indicates grinding. Figure 3-52
shows how contour and finish symbols are applied to a weldng symbol. This figure shows that the
weld is to be ground flush. Also, notice that the symbols are placed on the same side of the reference
line as the weld symbol.

7
Figure 3-52.-Finish and contour symbols.

Figure 3-53.-Specifying additional welding information.

Another supplementary symbol shown in figure 3-51 is the weld-all-around symbol. When this symbol
is placed on a welding symbol, welds are to continue all around the joint.

Welds that cannot be made in the shop are identified as field welds. A field weld symbol is shown in
figure 3-51. This symbol is a black flag that points toward the tail of the welding symbol.

Specifying Additional Information

It is sometimes necessary to specify a certain welding process, a type of electrode, or some type of
reference necessary to complete a weld. In this case, a note can be placed in the tail of the reference
line. (See

8
Figure 3-55.-Example of welding symbol in use.

fig. 3-53.) If additional information is not needed, then the tail is omitted.

Multiple-Weld Symbols

When you are fabricating a metal part, there are times when more than one type of weld is needed on
the same joint; for example, a joint may require both a bevel groove weld and a fillet weld. Two
methods of illustrating these weld symbols are shown in figure 3-54. Note that in each welding
symbol, the bevel groove weld is to be completed first, followed by the fillet weld.

Applying a Welding Symbol

Figure 3-55 shows an example of how a welding symbol may appear on a drawing. This figure shows
a

Figure 3-56.-Eye protection devices.

9
steel pipe column that is to be welded to a baseplate. The symbol tells the welder that the pipe is to be
beveled at a 30-degree angle followed by a bevel groove weld all around the joint. This is followed by
a 1/2-inch fillet weld that is also welded all around the joint. Finally, finish the fillet weld by grinding
it to a flush contour. As the field weld symbol indicates, all welds are to be accomplished in the field.

10