Stainless Steel Single-Point Load Cell Stainless Steel Single-Point Load Cell
Stainless Steel Single-Point Load Cell Stainless Steel Single-Point Load Cell
Stainless Steel Single-Point Load Cell Stainless Steel Single-Point Load Cell
Tedea-Huntleigh
APPLICATIONS
• Harsh environment small platforms
• Harsh environment check weighing
DESCRIPTION
Model 1130 is a low profile stainless steel single-point
load cell ideally designed for direct mounting in bench
Constructed in stainless steel this high accuracy load
and platform scales, packaging and process weighing
cell is approved to stringent approval standards, e.g.,
equipment, and is built to perform in harsh environments.
OIML and NTEP.
The small physical size, combined with high accuracy and
The two additional sense wires feed back the voltage
low cost, makes this load cell ideally suited for low profile
reaching the load cell. Complete compensation of
bench and counting scales. A special humidity resistant changes in lead resistance due to temperature change
protective coating assures long-term stability over the and/or cable extension, is acheived by feeding this
entire compensated temperature range. voltage into the appropriate electronics.
100
30
Optional Overload 35
Mounting Hole
M6 or 1/4"-28 UNC
135
106
14.5
25 15 27.7
4 Mounting Holes
M6 or 1/4"-20 UNC x10 Deep
SPECIFICATIONS
PARAMETER VALUE UNIT
Rated capacity—R.C. (Emax) 7, 10, 15, 20, 30, 50, 75, 100 kg
NTEP/OIML accuracy class NTEP(1) Non-Approved C3(2)
Maximum no. of intervals (n) 4000 single 1000 3000(3)
Y = Emax/Vmin 15000 2000 15000
Rated output—R.O. 2.0 mV/V
Rated output tolerance 0.2 ±mV/V
Zero balance 0.2 ±mV/V
Zero return, 30 min. 0.0250 0.0300 0.0170 ±% of applied load
Total error (per OIML R60) 0.0015 0.0500 0.0200 ±% of rated output
Temperature effect on zero 0.0030 0.0100 0.0023 ±% of rated output/°C
Temperature effect on output 0.0008 0.0030 0.0010 ±% of applied load/°C
Eccentric loading error 0.0035 0.0074 0.0049 ±% of rated load/cm
Temp. range, compensated –10 to +40 °C
Temp. range, safe –20 to +70 °C
Maximum safe central overload 150 % of R.C.
Ultimate central overload 300 % of R.C.
Excitation, recommended 10 VDC or VAC RMS
Excitation, maximum 15 VDC or VAC RMS
Input impedance 385±15 Ω
Output impedance 350±3 Ω
Insulation resistance >2000 MΩ
Cable length 1.5 m
Cable type 6-wire, PVC, single floating screen Standard
Construction Stainless steel
Environmental protection IP66
Platform size (max.) 400 × 400 mm
Recommended torque 13.0 N*m
(1)
Capacities 75 and 100kg are not NTEP approved
(2)
50% utilization
(3)
Capacities 50–75 kg
All specifications are subject to change without notice.
Disclaimer
ALL PRODUCTS, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Vishay Precision Group, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “VPG”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in
any other disclosure relating to any product.
The product specifications do not expand or otherwise modify VPG’s terms and conditions of purchase, including but
not limited to, the warranty expressed therein.
VPG makes no warranty, representation or guarantee other than as set forth in the terms and conditions of purchase.
To the maximum extent permitted by applicable law, VPG disclaims (i) any and all liability arising out of the
application or use of any product, (ii) any and all liability, including without limitation special, consequential or
incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose,
non-infringement and merchantability.
Information provided in datasheets and/or specifications may vary from actual results in different applications and
performance may vary over time. Statements regarding the suitability of products for certain types of applications
are based on VPG’s knowledge of typical requirements that are often placed on VPG products. It is the customer’s
responsibility to validate that a particular product with the properties described in the product specification is suitable for
use in a particular application. You should ensure you have the current version of the relevant information by contacting
VPG prior to performing installation or use of the product, such as on our website at vpgsensors.com.
No license, express, implied, or otherwise, to any intellectual property rights is granted by this document, or by any
conduct of VPG.
The products shown herein are not designed for use in life-saving or life-sustaining applications unless otherwise
expressly indicated. Customers using or selling VPG products not expressly indicated for use in such applications do
so entirely at their own risk and agree to fully indemnify VPG for any damages arising or resulting from such use or sale.
Please contact authorized VPG personnel to obtain written terms and conditions regarding products designed for such
applications.
Product names and markings noted herein may be trademarks of their respective owners.