CASE IH MAXXUM 125 TRACTOR Service Repair Manual PDF

SERVICE MANUAL
MAXXUM 100 , MAXXUM 110 Multicontroller , MAXXUM 110 , MAXXUM 115

Multicontroller , MAXXUM 115 , MAXXUM 120 Multicontroller , MAXXUM 120 ,
MAXXUM 125 Multicontroller , MAXXUM 125 , MAXXUM 130 Multicontroller ,
MAXXUM 130 , MAXXUM 140 Multicontroller , MAXXUM 140
MAXXUM-T3-DRAFT 02/11/2011
EN
Contents
INTRODUCTION
HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS A
PRIMARY HYDRAULIC POWER SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.10.A
PRIMARY HYDRAULIC POWER SYSTEM Closed center mechanical remote valve . . . A.10.B
PRIMARY HYDRAULIC POWER SYSTEM Electro-hydraulic remote valve . . . . . . . . . . . . . A.10.C
PRIMARY HYDRAULIC POWER SYSTEM Open center mechanical remote valve. . . . . A.10.D
SECONDARY HYDRAULIC POWER SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.12.A

HYDRAULIC COMMAND SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.14.A
ELECTRICAL POWER SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.30.A
ELECTRICAL POWER SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.30.A
ELECTRONIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.50.A
FAULT CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.50.A
ENGINE AND PTO IN ................................................................... B

ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.10.A
FUEL AND INJECTION SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.20.A
AIR INTAKE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.30.A
EXHAUST SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.40.A
ENGINE COOLANT SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.50.A
STARTING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.80.A
TRANSMISSION, DRIVE AND PTO OUT ........................................ C

POWER COUPLING Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.10.C
TRANSMISSION Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.20.B
TRANSMISSION Power Shuttle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.20.C
TRANSMISSION Semi-Powershift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.20.D
ADDITIONAL REDUCERS Creeper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.30.C
ADDITIONAL REDUCERS Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.30.D

REAR PTO Hydraulic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.40.C
FRONT PTO Hydraulic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.42.C
AXLES, BRAKES AND STEERING................................................. D
FRONT AXLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.10.A
REAR AXLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.12.A
2WD-4WD SYSTEM Hydraulic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.14.C
STEERING Hydraulic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.20.C
SERVICE BRAKE Hydraulic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.30.C
PARKING BRAKE Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.32.B

BRAKE CONNECTION Hydraulic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.34.C
SUSPENSION Hydraulic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.40.C
WHEELS AND TRACKS Wheels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.50.C
FRAME AND CAB ........................................................................ E

FRAME Primary frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E.10.B
SHIELD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E.20.A
USER CONTROLS AND SEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E.32.A
USER PLATFORM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E.34.A
ENVIRONMENT CONTROL Heating, ventilation and air-conditioning. . . . . . . . . . . . . . . . . . . E.40.D
HITCH AND WORKING TOOL ....................................................... H

HITCH Front hitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H.10.B
HITCH Rear hitch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H.10.C
HITCH Electronic draft control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H.10.D
INTRODUCTION
1
Contents
INTRODUCTION
Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Consumables Lubrications and Coolants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2
INTRODUCTION
Foreword [5195725]
Technical Information
This manual has been produced by a new technical information system. This new system is designed to deliver
technical information electronically through CD-ROM and in paper manuals. A coding system called ICE has been
developed to link the technical information to other Product Support functions e.g. Warranty.
Technical information is written to support the maintenance and service of the functions or systems on a customers
machine. When a customer has a concern on his machine it is usually because a function or system on his machine
is not working at all, is not working efficiently, or is not responding correctly to his commands. When you refer to the
technical information in this manual to resolve that customers concern, you will find all the information classified using
the new ICE coding, according to the functions or systems on that machine. Once you have located the technical
information for that function or system then you will find all the mechanical, electrical or hydraulic devices, compo-
nents, assemblies and sub assemblies for that function or system. You will also find all the types of information that
have been written for that function or system, the technical data (specifications), the functional data (how it works),
the diagnostic data (fault codes and troubleshooting) and the service data (remove, install adjust, etc.).
By integrating this new ICE coding into technical information , you will be able to search and retrieve just the right
piece of technical information you need to resolve that customers concern on his machine. This is made possible by
attaching 3 categories to each piece of technical information during the authoring process.
The first category is the Location, the second category is the Information Type and the third category is the Product:
• LOCATION - is the component or function on the machine, that the piece of technical information is going to
describe e.g. Fuel tank.
• INFORMATION TYPE - is the piece of technical information that has been written for a particular component or
function on the machine e.g. Capacity would be a type of Technical Data that would describe the amount of fuel
held by the Fuel tank.
• PRODUCT - is the model that the piece of technical information is written for.
Every piece of technical information will have those 3 categories attached to it. You will be able to use any combination
of those categories to find the right piece of technical information you need to resolve that customers concern on his
machine.
That information could be:

• the description of how to remove the cylinder head
• a table of specifications for a hydraulic pump
• a fault code
• a troubleshooting table
• a special tool
3
INTRODUCTION
How to Use this Manual

This manual is divided into Sections. Each Section is then divided into Chapters. Contents pages are included at the
beginning of the manual, then inside every Section and inside every Chapter. An alphabetical Index is included at the
end of a Chapter. Page number references are included for every piece of technical information listed in the Chapter
Contents or Chapter Index.
Each Chapter is divided into four Information types:

• Technical Data (specifications) for all the mechanical, electrical or hydraulic devices, components and, assem-
blies.
• Functional Data (how it works) for all the mechanical, electrical or hydraulic devices, components and assem-
blies.
• Diagnostic Data (fault codes, electrical and hydraulic troubleshooting) for all the mechanical, electrical or hy-
draulic devices, components and assemblies.
• Service data (remove disassembly, assemble, install) for all the mechanical, electrical or hydraulic devices,
components and assemblies.
Sections
Sections are grouped according to the main functions or a systems on the machine. Each Section is identified by
a letter A, B, C etc. The amount of Sections included in the manual will depend on the type and function of the
machine that the manual is written for. Each Section has a Contents page listed in alphabetic/numeric order. This
table illustrates which Sections could be included in a manual for a particular product.
SECTION
A - Distribution Systems
B - Power Production
C - Power Train
D - Travelling
E - Body and Structure
F - Frame Positioning
G - Tool Positioning
H - Working Arm
J - Tools and Couplers
K - Crop Processing
L - Field Processing
PRODUCT
Tractors X X X X X X X X
Vehicles with working arms: backhoes, X X X X X X X X X
excavators, skid steers, .....
Combines, forage harvesters, balers, .... X X X X X X X X X X
Seeding, planting, floating, spraying X X X X X X X X X
equipment, ....
Mounted equipment and tools, ..... X X X X
4
INTRODUCTION
This manual contains these Sections. The contents of each Section are explained over the following pages.
Contents
INTRODUCTION
DISTRIBUTION SYSTEMS A
POWER PRODUCTION B
POWER TRAIN C
TRAVELLING D
BODY AND STRUCTURE E
TOOL POSITIONING G
CROP PROCESSING K
Section Contents
SECTION A, DISTRIBUTION SYSTEMS
This Section covers the main systems that interact with most of the functions of the product. It includes the central
parts of the hydraulic, electrical, electronic, pneumatic, lighting and grease lubrication systems. The components that
are dedicated to a specific function are listed in the Chapter where all the technical information for that function is
included.
SECTION B, POWER PRODUCTION

This Section covers all the functions related to the production of power to move the machine and to drive various
devices.
SECTION C, POWER TRAIN

This Section covers all the functions related to the transmission of power from the engine to the axles and to internal
or external devices and additional Process Drive functions.
SECTION D, TRAVELLING
This Section covers all the functions related to moving the machine, including tracks, wheels, steering and braking. It
covers all the axles both driven axles and non-driven axles, including any axle suspension.
SECTION E, BODY AND STRUCTURE

This Section covers all the main functions and systems related to the structure and body of the machine. Including
the frame, the shields, the operator's cab and the platform.
SECTION G, TOOL POSITIONING

This Section covers all the functions related to the final and/or automatic positioning of the tool once the tool is posi-
tioned using the Working Arm or the machine frame.
SECTION K, CROP PROCESSING

This Section covers all the functions related to crop processing.
5
INTRODUCTION
Chapters
Each Chapter is identified by a letter and number combination e.g. Engine B.10.A The first letter is identical to the
Section letter i.e. Chapter B.10 is inside Section B, Power Production.
CONTENTS
The Chapter Contents lists all the technical data (specifications), functional data (how it works), service data (remove,
install adjust, etc..) and diagnostic data (fault codes and troubleshooting) that have been written in that Chapter for
that function or system on the machine.
Contents
POWER PRODUCTION
ENGINE _ 10.A
TECHNICAL DATA
ENGINE - General specification (B.10.A - D.40.A.10)
CS6050
FUNCTIONAL DATA
ENGINE - Dynamic description (B.10.A - C.30.A.10)

CS6050
SERVICE
ENGINE - Remove (B.10.A - F.10.A.10)
CS6050
DIAGNOSTIC
ENGINE - Troubleshooting (B.10.A - G.40.A.10)
CS6050
INDEX
The Chapter Index lists in alphabetical order all the types of information (called Information Units) that have been
written in that Chapter for that function or system on the machine.
Index
POWER PRODUCTION - B
ENGINE
ENGINE - Dynamic description (B.10.A - C.30.A.10)
CS6050
ENGINE - General specification (B.10.A - D.40.A.10)
CS6050
ENGINE - Remove (B.10.A - F.10.A.10)
CS6050
ENGINE - Troubleshooting (B.10.A - G.40.A.10)
CS6050
6
INTRODUCTION
Information Units and Information Search

Each chapter is composed of information units. Each information unit has the ICE code shown in parentheses which
indicates the function and the type of information written in that information unit. Each information unit has a page ref-
erence within that Chapter. The information units provide a quick and easy way to find just the right piece of technical
information you are looking for.
example information unit Stack valve - Sectional View (A.10.A.18 - C.10.A.30)

Information Unit ICE code A 10.A 18 C 10.A.30
ICE code classification Distribution Primary Stack valve Functional Sectional view
systems hydraulic data
power
CRIL03J033E01 1
Navigate to the correct information unit you are searching for by identifying the function and information type
from the ICE code.
• (1) Function and (2) Information type.
• (A) corresponds to the sections of the repair manual.
(B) corresponds to the chapters of the repair manual.
(C) corresponds to the type of information listed in the chapter contents, Technical data, Functional Data, Diag-
nostic or Service.
(A) and (B) are also shown in the page numbering on the page footer.
THE REST OF THE CODING IS NOT LISTED IN ALPHANUMERIC ORDER IN THIS MANUAL.
• You will find a table of contents at the beginning and end of each section and chapter.
You will find an alphabetical index at the end of each chapter.
• By referring to (A), (B) and (C) of the coding, you can follow the contents or index (page numbers) and quickly
find the information you are looking for.
Page Header and Footer

The page header will contain the following references:
• Section and Chapter description
The page footer will contain the following references:

• Publication number for that Manual, Section or Chapter.
• Version reference for that publication.
• Publication date
• Section, chapter and page reference e.g. A.10.A / 9
7
INTRODUCTION
Important information
All repair and maintenance works listed in this manual must be carried out only by staff belonging to the Case I H
Service network, strictly complying with the instructions given and using, whenever required, the special tools.
Anyone who carries out the above operations without complying with the prescriptions shall be responsible for the
subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional or
local dealers, reject any responsibility for damages due to the anomalous behaviour of parts and/or components not
approved by the manufacturer himself, including those used for the servicing or repair of the product manufactured
or marketed by the Manufacturer. In any case, no warranty is given or attributed on the product manufactured or
marketed by the Manufacturer in case of damages due to an anomalous behaviour of parts and/or components not
approved by the Manufacturer.
8
INTRODUCTION
Safety rules [3964943]

IMPORTANT NOTICE
All maintenance and repair operations described in this manual should be carried out exclusively by authorised work-
shops. All instructions should be carefully observed and special equipment where indicated should be used.
Anyone who carries out service operations described without carefully observing these instructions will be directly
responsible for any damage caused.
NOTES FOR EQUIPMENT

Equipment shown in this manual is:
• designed expressly for use on these tractors;
• necessary to make a reliable repair;
• accurately built and strictly tested to offer efficient and long-lasting working life.
NOTICES
The words “front”, “rear”, “right hand”, and “left hand” refer to the different parts as seen from the operator’s seat
oriented to the normal direction of movement of the tractor.
SAFETY RULES
PAY ATTENTION TO THIS SYMBOL

This warning symbol points out important messages involving personal
safety. Carefully read the safety rules contained herein and follow advised
precautions to avoid potential hazards and safeguard your safety.
In this manual you will find this symbol together with the following
key-words:
WARNING -it gives warning about improper repair operations and potential
consequences affecting the service technician’s personal safety.
DANGER - it gives specific warning about potential dangers for personal
safety of the operator or other persons directly or indirectly involved in
the operation.
TO PREVENT ACCIDENTS
Most accidents and personal injuries taking place in workshops are due from non-observance of some essential rules
and safety precautions.
The possibility that an accident might occur with any type of machines should not be disregarded, no matter how well
the machine in question was designed and built.
A wise and careful service technician is the best precautions against accidents.
Careful observance of this basic precaution would be enough to avoid many severe accidents.
DANGER
Never carry out any cleaning, lubrication or maintenance operations when the engine is running.
B013
SAFETY RULES
Generalities
• Carefully follow specified repair and maintenance procedures.
9
INTRODUCTION
• Do not wear rings, wristwatches, jewels, unbuttoned or flapping clothing such as ties, torn clothes, scarves,
open jackets or shirts with open zips which could get caught on moving parts. Use approved safety clothing
such as anti-slipping footwear, gloves, safety goggles, helmets, etc.
• Wear safety glasses with side guards when cleaning parts using compressed air.
• Damaged or frayed wires and chains are unreliable. Do not use them for lifting or towing.
• Wear suitable protection such as approved eye protection, helmets, special clothing, gloves and footwear when-
ever welding. All persons standing in the vicinity of the welding process should wear approved eye protection.
NEVER LOOK AT THE WELDING ARC IF YOUR EYES ARE NOT SUITABLY PROTECTED.
• Never carry out any repair on the machine if someone is sitting on the operator’s seat, except if they are qualified
operators assisting in the operation to be carried out.
• Never operate the machine or use attachments from a place other than sitting at the operator’s seat or at the
side of the machine when operating the fender switches.
• Never carry out any operation on the machine when the engine is running, except when specifically indicated.
Stop the engine and ensure that all pressure is relieved from hydraulic circuits before removing caps, covers,
valves, etc.
• All repair and maintenance operations should be carried out with the greatest care and attention.
• Disconnect the batteries and label all controls to warn that the tractor is being serviced. Block the machine and
all equipment which should be raised.
• Never check or fill fuel tanks or batteries, nor use starting liquid if you are smoking or near open flames as such
fluids are flammable.
• The fuel filling gun should always remain in contact with the filler neck. Maintain this contact until the fuel stops
flowing into the tank to avoid possible sparks due to static electricity build-up.
• To transfer a failed tractor, use a trailer or a low loading platform trolley if available.
• To load and unload the machine from the transportation means, select a flat area providing a firm support to the
trailer or truck wheels. Firmly tie the machine to the truck or trailer platform and block wheels as required by the
transporter.
• Always use lifting equipment of appropriate capacity to lift or move heavy components.
• Chains should always be safely fastened. Ensure that fastening device is strong enough to hold the load fore-
seen. No persons should stand near the fastening point.
• The working area should be always kept CLEAN and DRY. Immediately clean any spillage of water or oil.
• Never use gasoline, diesel oil or other flammable liquids as cleaning agents. Use non-flammable non-toxic
proprietary solvents.
• Do not pile up grease or oil soaked rags, as they constitute a great fire hazard. Always place them into a metal
container.
START UP
• Never run the engine in confined spaces which are not equipped with adequate ventilation for exhaust gas
extraction.
• Never bring your head, body, arms, legs, feet, hands, fingers near fans or rotating belts.
ENGINE
• Always loosen the radiator cap very slowly before removing it to allow pressure in the system to dissipate.
Coolant should be topped up only when the engine is stopped.
• Do not fill up fuel tank when the engine is running.
• Never adjust the fuel injection pump when the tractor is moving.
• Never lubricate the tractor when the engine is running.
ELECTRICAL SYSTEMS
• If it is necessary to use auxiliary batteries, cables must be connected at both sides as follows: (+) to (+) and
(-) to (-). Avoid short-circuiting the terminals. GAS RELEASED FROM BATTERIES IS HIGHLY FLAMMABLE.
10
INTRODUCTION
During charging, leave the battery compartment uncovered to improve ventilation. Avoid sparks or flames near
the battery area. Do no smoke.
• Do not charge batteries in confined spaces.
• Always disconnect the batteries before performing any type of service on the electrical system.
HYDRAULIC SYSTEMS
• Some fluid coming out from a very small port can be almost invisible and be strong enough to penetrate the skin.
For this reason, NEVER USE YOUR HANDS TO CHECK FOR LEAKS, but use a piece of cardboard or a piece
of wood for this purpose. If any fluid is injected into the skin, seek medical aid immediately. Lack of immediate
medical attention may result in serious infections or dermatitis.
• Always take system pressure readings using the appropriate gauges.
WHEELS AND TYRES

• Check that the tyres are correctly inflated at the pressure specified by the manufacturer. Periodically check for
possible damage to the rims and tyres.
• Stay at the tyre side when inflating.
• Check the pressure only when the tractor is unloaded and tyres are cold to avoid wrong readings due to over-
pressure.
• Never cut, nor weld a rim with the inflated tyre assembled.
• To remove the wheels, block both front and rear tractor wheels. Raise the tractor and install safe and stable
supports under the tractor in accordance with regulations in force.
• Deflate the tyre before removing any object caught into the tyre tread.
• Never inflate tyres using flammable gases as they may generate explosions and cause injuries to bystanders.
REMOVAL AND INSTALLATION

• Lift and handle all heavy components using lifting equipment of adequate capacity. Ensure that parts are sup-
ported by appropriate slings and hooks. Use lifting eyes provided to this purpose. Take care of the persons
near the loads to be lifted.
HEALTH AND SAFETY
CONTENT
Section Description Page
HEALTH AND SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ACIDS AND ALKALIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ADHESIVES AND SEALERS - see Fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ANTIFREEZE - see Fire, Solvents e.g. Isopropanol, Ethylene Glycol, Methanol. . . . . . 5
ARC WELDING - see Welding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
BATTERY ACIDS - see Acids and Alkalis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
BRAKE AND CLUTCH FLUIDS (Polyalkylene Glycols) - see Fire. . . . . . . . . . . . . 6
BRAZING - see Welding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
CHEMICAL MATERIALS - GENERAL - see Legal Aspects. . . . . . . . . . . . . . . . . 6
DO’S. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
DO NOTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
CORROSION PROTECTION MATERIALS - see Solvents, Fire. . . . . . . . . . . . . . . 6
DUSTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ELECTRIC SHOCK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
EXHAUST FUMES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
FIBRE INSULATION - see Dusts.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
FIRE - see Welding, Foams, Legal Aspects.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
FIRST AID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
FOAMS - Polyurethane - see Fire.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
11
INTRODUCTION
FUELS - see Fire, Legal Aspects, Chemicals - General, Solvents.. . . . . . . . . . . . . . . . 8

GAS CYLINDERS - see Fire.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
GENERAL WORKSHOP TOOLS AND EQUIPMENT. . . . . . . . . . . . . . . . . . . . . 9
LEGAL ASPECTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
LUBRICANTS AND GREASES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
PAINTS - see Solvents and Chemical Materials - General.. . . . . . . . . . . . . . . . . . . . . 10
SOLDER - see Welding.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SOLVENTS - see Chemical Materials - General Fuels (Kerosene), Fire.. . . . . . . . . .. 10
SUSPENDED LOADS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
WELDING - see Fire, Electric Shock, Gas Cylinders.. . . . . . . . . . . . . . . . . . . . . . . . 11
HEALTH AND SAFETY PRECAUTIONS

Many of the procedures associated with vehicle maintenance and repair involve physical hazards or other risks to
health. This section lists, alphabetically, some of these hazardous operations and the materials and equipment asso-
ciated with them. The precautions necessary to avoid these hazards are identified.
The list is not exhaustive and all operations and procedures and the handling of materials, should be carried out with
health and safety in mind.
ACIDS AND ALKALIS

see Battery acids, e.g. caustic soda, sulphuric acid.
Used in batteries and cleaning materials.
Irritant and corrosive to the skin, eyes, nose and throat. Causes burns.
Avoid splashes to the skin, eyes and clothing. Wear suitable protective gloves and goggles. Can destroy ordinary
protective clothing. Do not breathe mists.
Ensure access to water and soap is readily available for splashing accidents.
ADHESIVES AND SEALERS

see Fire
Highly Flammable, Flammable, combustible.
Generally should be stored in “No Smoking” areas; cleanliness and tidiness in use should be observed, e.g. dispos-
able paper covering benches; should be dispensed from applicators where possible; containers, including secondary
containers, should be labelled.
Solvent based Adhesives/Sealers

See Solvents.
Follow manufacturers instructions.
Water based Adhesives/Sealers

Those based on polymer emulsions and rubber lattices may contain small amounts of volatile toxic and harmful chem-
icals. Skin and eye contact should be avoided and adequate ventilation provided during use.
Resin based Adhesives/Sealers

e.g. epoxide and formaldehyde resin based.
Mixing should only be carried out in well ventilated areas as harmful or toxic volatile chemicals may be released.
Skin contact with uncured resins and hardeners can result in irritation; dermatitis and absorption of toxic or harmful
chemicals through the skin. Splashes can damage the eyes.
Provide adequate ventilation and avoid skin and eye contact. Follow manufacturers instructions.
Anaerobic, Cyanoacrylate and other Acrylic Adhesives

Many are irritant, sensitizing or harmful to the skin. Some are eye irritants.
12
INTRODUCTION
Skin and eye contact should be avoided and the manufacturers instructions followed.
Cyanoacrylate adhesives (super-glues) must not contact the skin or eyes. If skin or eye tissue is bonded cover with a
clean moist pad and get medical attention. do not attempt to pull tissue apart. Use in well ventilated areas as vapours
can cause irritation of the nose and eyes.
For two-pack systems see Resin based adhesives/sealers.
Isocyanate (Polyurethane) Adhesives/ Sealers

see Resin based Adhesives.
Individuals suffering from asthma or respiratory allergies should not work with or near these materials as sensitivity
reactions can occur.
Any spraying should preferably be carried out in exhaust ventilated booths removing vapours and spray droplets from
the breathing zone. Individuals working with spray applications should wear supplied air respirators.
ANTIFREEZE
see Fire, Solvents e.g. Isopropanol, Ethylene Glycol, Methanol.
Highly Flammable, Flammable, Combustible.
Used in vehicle coolant systems, brake air pressure systems, screenwash solutions.
Vapours given off from coolant antifreeze (glycol) arise only when heated.
Antifreeze may be absorbed through the skin in toxic or harmful quantities. Antifreeze if swallowed is fatal and medical
attention must be found immediately.
ARC WELDING
see Welding.
BATTERY ACIDS
see Acids and Alkalis.
Gases released during charging are explosive.
Never use naked flames or allow sparks near charging or recently charged batteries.
BRAKE AND CLUTCH FLUIDS (Polyalkylene Glycols)

see Fire.
Combustible.
Splashes to the skin and eyes are slightly irritating.
Avoid skin and eye contact as far as possible.
Inhalation of vapour hazards do not arise at ambient temperatures because of the very low vapour pressure.
BRAZING
see Welding.
CHEMICAL MATERIALS - GENERAL

see Legal Aspects.
Chemical materials such as solvents, sealers, adhesives, paints, resin foams, battery acids, antifreeze, brake fluids,
oils and grease should always be used with caution and stored and handled with care. They may be toxic, harmful,
corrosive, irritant or highly inflammable and give rise to hazardous fumes and dusts.
The effects of excessive exposure to chemicals may be immediate or delayed; briefly experienced or permanent;
cumulative; superficial; life threatening; or may reduce life-expectancy.
DO’S
Do remove chemical materials from the skin and clothing as soon as practicable after soiling. Change heavily soiled
clothing and have it cleaned.
Do carefully read and observe hazard and precaution warnings given on material containers (labels) and in any
accompanying leaflets, poster or other instructions. Material health and safety data sheets can be obtained from
Manufacturers.
13
INTRODUCTION
Do organise work practices and protective clothing to avoid soiling of the skin and eyes; breathing vapours/aerosols/
dusts/fumes; inadequate container labelling; fire and explosion hazards.
Do wash before job breaks; before eating, smoking, drinking or using toilet facilities when handling chemical materials.
Do keep work areas clean, uncluttered and free of spills.
Do store according to national and local regulations.
Do keep chemical materials out of reach of children.
DO NOTS
Do Not mix chemical materials except under the manufacturers instructions; some chemicals can form other toxic or
harmful chemicals; give off toxic or harmful fumes; be explosive when mixed together.
Do Not spray chemical materials, particularly those based on solvents, in confined spaces e.g. when people are
inside a vehicle.
Do Not apply heat or flame to chemical materials except under the manufacturers’ instructions. Some are highly
inflammable and some may release toxic or harmful fumes.
Do Not leave containers open. Fumes given off can build up to toxic, harmful or explosive concentrations. Some
fumes are heavier than air and will accumulate in confined areas, pits etc.
Do Not transfer chemical materials to unlabeled containers.
Do Not clean hands or clothing with chemical materials. Chemicals, particularly solvents and fuels will dry the skin
and may cause irritation with dermatitis. Some can be absorbed through the skin in toxic or harmful quantities.
Do Not use emptied containers for other materials, except when they have been cleaned under supervised conditions.
Do Not sniff or smell chemical materials. Brief exposure to high concentrations of fumes can be toxic or harmful.
Clutch Fluids
see Brake and Clutch Fluids.
Clutch Linings and Pads

see Brake and Clutch Linings and Pads.
CORROSION PROTECTION MATERIALS

see Solvents, Fire.
Highly flammable, flammable.
These materials are varied and the manufacturers instructions should be followed. They may contain solvents, resins,
petroleum products etc. Skin and eye contact should be avoided. They should only be sprayed in conditions of
adequate ventilation and not in confined spaces.
Cutting
see Welding.
De-Waxing
see Solvents and Fuels (Kerosene).
DUSTS
Powder, dusts or clouds may be irritant, harmful or toxic. Avoid breathing dusts from powdery chemical materials or
those arising from dry abrasion operations. Wear respiratory protection if ventilation is inadequate.
ELECTRIC SHOCK
Electric shocks can result from the use of faulty electrical equipment or from the misuse of equipment even in good
condition.
Ensure that electrical equipment is maintained in good condition and frequently tested.
Ensure that flexes, cables, plugs and sockets are not frayed, kinked, cut, cracked or otherwise damaged.
Ensure that electric equipment is protected by the correct rated fuse.
Never misuse electrical equipment and never use equipment which is in any way faulty. The results could be fatal.
Use reduced voltage equipment ( 110 volt) for inspection and working lights where possible.
14
INTRODUCTION
Ensure that the cables of mobile electrical equipment cannot get trapped and damaged, such as in a vehicle hoist.
Use air operated mobile equipment where possible in preference to electrical equipment.
In cases of electrocution:-
• switch off electricity before approaching victim
• if this is not possible, push or drag victim from source of electricity using dry non-conductive material
• commence resuscitation if trained to do so
• SUMMON MEDICAL ASSISTANCE
EXHAUST FUMES
These contain asphyxiating, harmful and toxic chemicals and particles such as carbon oxides, nitrogen oxides, alde-
hydes, lead and aromatic hydrocarbons. Engines should only be run under conditions of adequate extraction or
general ventilation and not in confined spaces.
Gasolene (Petrol) Engine

There may not be adequate warning properties of odour or irritation before immediate and delayed toxic or harmful
effects arise.
Diesel Engine
Soot, discomfort and irritation usually give adequate warning of hazardous fume concentrations.
FIBRE INSULATION
see Dusts.
Used in noise and sound insulation.
The fibrous nature of surfaces and cut edges can cause skin irritation. This is usually a physical and not a chemical
effect.
Precautions should be taken to avoid excessive skin contact through careful organisation of work practices and the
use of gloves.
FIRE
see Welding, Foams, Legal Aspects.
Many of the materials found on or associated with the repair of vehicles are highly flammable. Some give off toxic or
harmful fumes if burnt.
Observe strict fire safety when storing and handling flammable materials or solvents, particularly near electrical equip-
ment or welding processes.
Ensure before using electrical or welding equipment but that there is no fire hazard present.
Have a suitable fire extinguisher available when using welding or heating equipment.
FIRST AID
Apart from meeting any legal requirements it is desirable for someone in the workshop to be trained in first aid proce-
dures.
Splashes in the eye should be flushed with clean water for at least ten minutes.
Soiled skin should be washed with soap and water.
Inhalation affected individuals should be removed to fresh air immediately.
If swallowed or if effects persist consult a doctor with information (label) on material used.
Do not induce vomiting (unless indicated by manufacturer).
FOAMS - Polyurethane
see Fire.
Used in sound and noise insulation. Cured foams used in seat and trim cushioning.
Unreacted components are irritating and may be harmful to the skin and eyes. Wear gloves and goggles.
15
INTRODUCTION
Individuals with chronic respiratory diseases, asthma, bronchial medical problems or histories of allergic diseases
should not work with or near uncured materials.
The components, vapours, spray mists can cause direct irritation, sensitivity reactions and may be toxic or harmful.
Vapours and spray mists must not be breathed. These materials must be applied with adequate ventilation and res-
piratory protection. Do not remove respirator immediately after spraying, wait until vapour/ mists have cleared.
Burning of the uncured components and the cured foams can generate toxic and harmful fumes.
Smoking, open flames or the use of electrical equipment during foaming operations and until vapours/mists have
cleared should not be allowed.
Any heat cutting of cured foams or partially cured foams should be conducted with extraction ventilation (see Body
Section 44 Legal and Safety Aspects).
FUELS
see Fire, Legal Aspects, Chemicals - General, Solvents.
Used as fuels and cleaning agents.
Gasolene (Petrol).
Highly flammable.
Swallowing can result in mouth and throat irritation and absorption from the stomach can result in drowsiness and
unconsciousness. Small amounts can be fatal to children. Aspiration of liquid into the lungs, e.g. through vomiting,
is a very serious hazard.
Gasolene dries the skin and can cause irritation and dermatitis on prolonged or repeated contact. Liquid in the eye
causes severe smarting.
Motor gasolene may contain appreciable quantities of benzene, which is toxic upon inhalation and the concentrations
of gasolene vapours must be kept very low. High concentrations will cause eye, nose and throat irritation, nausea,
headache, depression and symptoms of drunkenness. Very high concentrations will result in rapid loss of conscious-
ness.
Ensure there is adequate ventilation when handling and using gasolene. Great care must be taken to avoid the serious
consequences of inhalation in the event of vapour build up arising from spillages in confined spaces.
Special precautions apply to cleaning and maintenance operations on gasolene storage tanks.
Gasolene should not be used as a cleaning agent. It must not be siphoned by mouth.
Kerosene (Paraffin)
Used also as heating fuel, solvent and cleaning agent.
Flammable.
Irritation of the mouth and throat may result from swallowing. The main hazard from swallowing arises if liquid aspi-
ration into the lungs occurs. Liquid contact dries the skin and can cause irritation or dermatitis. Splashes in the eye
may be slightly irritating.
In normal circumstances the low volatility does not give rise to harmful vapours. Exposure to mists and vapours from
kerosene at elevated temperatures should be avoided (mists may arise in de-waxing).
Avoid skin and eye contact and ensure there is adequate ventilation.
Gas-Oil (Diesel Fuel)

see Fuels (Kerosene).
Combustible.
Gross or prolonged skin contact with high boiling gas oils may also cause serious skin disorders including skin cancer.
GAS CYLINDERS
see Fire.
Gases such as oxygen, acetylene, carbon dioxide, argon and propane are normally stored in cylinders at pressures of
up to 140 bar( 2000 lb/in2) and great care should be taken in handling these cylinders to avoid mechanical damage to
them or to the valve gear attached. The contents of each cylinder should be clearly identified by appropriate markings.
Cylinders should be stored in well ventilated enclosures, and protected from ice and snow, or direct sunlight. Fuel
gases (e.g. acetylene and propane) should not be stored in close proximity to oxygen cylinders.
Care should be exercised to prevent leaks from gas cylinders and lines, and to avoid sources of ignition.
Only trained personnel should undertake work involving gas cylinders.
16
INTRODUCTION
Gases
see Gas Cylinders.
Gas Shielded Welding

see Welding.
Gas Welding
see Welding.
GENERAL WORKSHOP TOOLS AND EQUIPMENT

It is essential that all tools and equipment are maintained in good condition and the correct safety equipment used
where required.
Never use tools or equipment for any purpose other than that for which they were designed.
Never overload equipment such as hoists, jacks, axle and chassis stands or lifting slings. Damage caused by over-
loading is not always immediately apparent and may result in a fatal failure the next time that the equipment is used.
Do not use damaged or defective tools or equipment, particularly high speed equipment such as grinding wheels. A
damaged grinding wheel can disintegrate without warning and cause serious injury.
Wear suitable eye protection when using grinding, chiselling or sand blasting equipment.
Wear a suitable breathing mask when using sand blasting equipment, working with asbestos based materials or using
spraying equipment.
Glues
see Adhesives and Sealers.
High Pressure Air, Lubrication and Oil Test Equipment accordance with local regulations
see Lubricants and Greases.
Always keep high pressure equipment in good condition and regularly maintained, particularly at joints and unions.
Never direct a high pressure nozzle at the skin as the fluid may penetrate to the underlying tissue etc. and cause
serious injury.
LEGAL ASPECTS
Many laws and regulations make requirements relating to health and safety in the use of materials and equipment in
workshops. Always conform to the laws and regulations applicable to the country in which you are working.
Workshops should be familiar, in detail, with the associated laws and regulations. Consult the local factory inspec-
torate or appropriate authority if in any doubt.
LUBRICANTS AND GREASES

Avoid all prolonged and repeated contact with mineral oils, especially used oils. Used oils contaminated during service
(e.g. routine service change sump oils) are more irritating and more likely to cause serious effects including skin
cancer in the event of gross and prolonged skin contact.
Wash skin thoroughly after work involving oil. Proprietary hand cleaners may be of value provided they can be re-
moved from the skin with water. Do not use petrol, paraffin or other solvents to remove oil from the skin.
Lubricants and greases may be slightly irritating to the eyes.
Repeated or prolonged skin contact should be avoided by wearing protective clothing if necessary. Particular care
should be taken with used oils and greases containing lead. Do not allow work clothing to be contaminated with oil.
Dry clean or launder such clothing at regular intervals. Discard oil soaked shoes.
Do not employ used engine oils as lubricants or for any application where appreciable skin contact is likely to occur.
Used oils may only be disposed of in accordance with local regulations.
Noise Insulation Materials

see Foams, Fibre Insulation.
17
INTRODUCTION
PAINTS
see Solvents and Chemical Materials - General.
Highly Flammable, Flammable.
One Pack. Can contain harmful or toxic pigments, driers and other components as well as solvents. Spraying should
only be carried out with adequate ventilation.
Two Pack. Can also contain harmful and toxic unreacted resins and resin hardening agents. The manufacturers
instructions should be followed and the section of page 5 on resin based adhesives, isocyanate containing Adhesives
and Foams should be consulted.
Spraying should preferably be carried out in exhausted ventilated booths removing vapour and spray mists from the
breathing zone. Individuals working in booths should wear respiratory protection. Those doing small scale repair work
in the open shop should wear supplied air respirators.
Paint Thinners
see Solvents.
Petrol
see Fuels (Gasolene).
Pressurised Equipment
see High Pressure Air, Lubrication and Oil Test Equipment.
Resistance Welding
see Welding.
Sealers
see Adhesives and Sealers.
SOLDER
see Welding.
Solders are mixtures of metals such that the melting point of the mixture is below that of the constituent metals (nor-
mally lead and tin). Solder application does not normally give rise to toxic lead fumes, provided a gas/air flame is
used. Oxy-acetylene flames should not be used, as they are much hotter and will cause lead fumes to be evolved.
Some fumes may be produced by the application of any flame to surfaces coated with grease etc. and inhalation of
these should be avoided.
Removal of excess solder should be undertaken with care, to ensure that fine lead dust is not produced, which can
give toxic effects if inhaled. Respiratory protection may be necessary.
Solder spillage and filing should be collected and removed promptly to prevent general air contamination by lead.
High standards of personal hygiene are necessary in order to avoid indigestion of lead or inhalation of solder dust
from clothing.
SOLVENTS
see Chemical Materials - General Fuels (Kerosene), Fire.
e.g. Acetone, white spirit, toluene, xylene, trichlorethane.
Used in cleaning materials, de-waxing, paints, plastics, resins, thinners etc.
Highly Inflammable, Flammable.
Skin contact will degrease the skin and may result in irritation and dermatitis following repeated or prolonged contact.
Some can be absorbed through the skin in toxic or harmful quantities.
Splashes in the eye may cause severe irritation and could lead to loss of vision.
Brief exposure to high concentrations of vapours or mists will cause eye and throat irritation, drowsiness, dizziness,
headaches and in the worst circumstances, unconsciousness.
Repeated or prolonged exposures to excessive but lower concentrations of vapours or mists, for which there might
not be adequate warning indications, can cause more serious toxic or harmful effects.
Aspiration into the lungs (e.g. through vomiting) is the most serious consequence of swallowing.
18
INTRODUCTION
Avoid splashes to the skin, eyes and clothing. Wear protective gloves, goggles and clothing if necessary.
Ensure good ventilation when in use, avoid breathing fumes, vapours and spray mists and keep containers tightly
sealed. Do not use in confined spaces.
When the spraying material contains solvents, e.g. paints, adhesives, coatings, use extraction ventilation or personal
respiratory protection in the absence of adequate general ventilation.
Do not apply heat or flame except under specific and detailed manufacturers instructions.
Sound Insulation
see Fibre Insulation, Foams.
Spot Welding
see Welding.
SUSPENDED LOADS
There is always a danger when loads are lifted or suspended. Never work under an unsupported suspended or raised
load, e.g. jacked up vehicle, suspended engine, etc.
Always ensure that lifting equipment such as jacks, hoists, axle stands, slings, etc. are adequate and suitable for the
job, in good condition and regularly maintained.
Never improvise lifting tackle.
Underseal
see Corrosion Protection.
WELDING
see Fire, Electric Shock, Gas Cylinders.
Welding processes include Resistance Welding (Spot Welding), Arc Welding and Gas Welding.
Resistance Welding
This process may cause particles of molten metal to be emitted at high velocity and the eyes and skin must be pro-
tected.
Arc Welding
This process emits a high level of ultraviolet radiation which may cause eye and skin burns to the welder and to other
persons nearby. Gas-shielded welding processes are particularly hazardous in this respect. Personal protection must
be worn, and screens used to shield other people.
Metal spatter will also occur and appropriate eye and skin protection is necessary.
The heat of the welding arc will produce fumes and gases from the metals being welded and from any applied coatings
or contamination on the surfaces being worked on. These gases and fumes may be toxic and inhalation should
always be avoided. The use of extraction ventilation to remove the fumes from the working area may be necessary,
particularly in cases where the general ventilation is poor, or where considerable welding work is anticipated. In
extreme cases where adequate ventilation cannot be provided, supplied air respirators may be necessary.
Gas Welding
Oxy-acetylene torches may be used for welding and cutting and special care must be taken to prevent leakage of
these gases, with consequent risk of fire and explosion.
The process will produce metal spatter and eye and skin protection is necessary.
The flame is bright and eye protection should be used, but the ultra-violet emission is much less than that from arc
welding, and lighter filters may be used.
The process itself produces few toxic fumes, but such fumes and gases may be produced from coatings on the work,
particularly during cutting away of damaged body parts and inhalation of the fumes should be avoided.
In brazing, toxic fumes may be evolved from the metals in the brazing rod, and a severe hazard may arise if brazing
rods containing cadmium are used. In this event particular care must be taken to avoid inhalation of fumes and expert
advice may be required.
19
INTRODUCTION
SPECIAL PRECAUTIONS MUST BE TAKEN BEFORE ANY WELDING OR CUTTING TAKES PLACE ON VESSELS
WHICH HAVE CONTAINED COMBUSTIBLE MATERIALS, E.G. BOILING OR STEAMING OUT OF FUEL TANKS.
White Spirit
see Solvents.
ECOLOGY AND THE ENVIRONMENT

Soil, air and water are vital factors of agriculture and life in general. Where legislation does not yet rule the treatment
of some of the substances which are required by advanced technology, common sense should govern the use and
disposal of products of a chemical and petrochemical nature.
The following are recommendations which may be of assistance:

• Become acquainted with and ensure that you understand the relative legislation applicable to your country.
• Where no legislation exists, obtain information from suppliers of oils, filters, batteries, fuels, anti freeze, cleaning
agents, etc., with regard to their effect on man and nature and how to safely store, use and dispose of these
substances. Agricultural consultants will, in many cases, be able to help you as well.
HELPFUL HINTS
1. Avoid filling tanks using unsuitable containers or inappropriate pressurised fuel delivery systems which may
cause considerable spillage.
2. In general, avoid skin contact with all fuels, oils, acids, solvents, etc. Most of them contain substances which
can be harmful to your health.
3. Modern oils contain additives. Do not burn contaminated fuels and/or waste oils in ordinary heating systems.
4. Avoid spillage when draining off used engine coolant mixtures, engine, gearbox and hydraulic oils, brake fluids,
etc. Do not mix drained brake fluids or fuels with lubricants. Store them safely until they can be disposed of in
a proper way to comply with local legislation and available resources.
5. Modern coolant mixtures, i.e. antifreeze and other additives, should be replaced every two years. They should
not be allowed to get into the soil but should be collected and disposed of safely.
6. Do not open the air-conditioning system yourself. It contains gases which should not be released into the at-
mosphere. Your dealer or air conditioning specialist has a special extractor for this purpose and will have to
recharge the system anyway.
7. Repair any leaks or defects in the engine cooling or hydraulic system immediately.
8. Do not increase the pressure in a pressurised circuit as this may lead to the components exploding.
9. Protect hoses during welding as penetrating weld splatter may burn a hole or weaken them, causing the loss of
oils, coolant, etc.
20
INTRODUCTION
Torque [9696959]
Minimum hardware tightening torques for normal assembly applications unless otherwise
stated
NOTICE: Shown below is the suggested initial torque tightening sequences for general applications, tighten in se-
quence from item 1 through to the last item of the hardware.
df5019-1 1
Imperial hardware
Nominal SAE SAE SAE SAE SAE SAE LOCK- LOCK-
Size GRADE 2 GRADE GRADE 5 GRADE GRADE GRADE NUTS NUTS
Unplated 2 plated Unplated 5 plated 8Unplated 8 plated GR.B GR.B
or Silver w/ZnCr or Silver w/ZnCr or Silver w/ZnCr w/GR5 w/GR8
plated GOLD plated GOLD plated GOLD BOLT BOLT
1/4 6.2 Nm 8.1 Nm 9.7 Nm 13 Nm 14 Nm 18 Nm 6.9 Nm 9.8 Nm
55 lb in 72 lb in 86 lb in 112 lb in 121 lb in 157 lb in 61 lb in 86 lb in
5/16 13 Nm 17 Nm 20 Nm 26 Nm 28 Nm 37 Nm 14 Nm 20 Nm
115 lb in 149 lb in 178 lb in 229 lb in 250 lb in 324 lb in 125 lb in 176 lb in
17 lb ft 22 lb ft 26 lb ft 34 lb ft 37 lb ft 48 lb ft 19 lb ft 26 lb ft
1.0 289 Nm 373 Nm 742 Nm 960 Nm 1048 Nm 1356 Nm 523 Nm 739 Nm
21
INTRODUCTION
Metric hardware
Nominal CLASS 5.8 CLASS 5.8 CLASS 8.8 CLASS 8.8 CLASS 10.9 CLASS 10.9 LOCKNUT
Size UNPLATED UNPLATED UNPLATED UNPLATED UNPLATED UNPLATED CL.8
w/CL8.8
BOLT
M4 1.7 Nm 2.2 Nm 2.6 Nm 3.4 Nm 3.7 Nm 4.8 Nm 1.8 Nm
15 lb in 19 lb in 23 lb in 30 lb in 33 lb in 42 lb in 16 lb in
M6 5.8 Nm 7.6 Nm 8.9 Nm 12 Nm 13 Nm 17 Nm 6.3 Nm
M8 14 Nm 18 Nm 22 Nm 28 Nm 31 Nm 40 Nm 15 Nm
21 lb ft 27 lb ft 32 lb ft 41 lb ft 45 lb ft 58 lb ft 22 lb ft
20083680 2
Identification - Hexagon cap screw and carriage bolts classes 5.6 and onwards
1.Manufacturers identification 2. Property class
20083681 3
Identification - Hexagonal nuts and locknuts classes 05 onwards

1. Manufacturers identification 2. Property class
3. Clock marking
22
INTRODUCTION
20083682 4
Identification - Cap screws and carriage bolts

1. SAE grade 2 2. SAE grade 5
3. SAE grade 8 4. Regular nuts
5. SAE grade 5 hex nuts 6. SAE grade 8 hex nuts
20083683 5
Locknuts - grade identification

Grade A : no notches Grade B : one circumferential notch
Grade C : two circumferential notches
20083684 6

Grade A : no marks Grade B : three marks
Grade C : six marks
23
INTRODUCTION
20083685 7

Grade A : no marks Grade B : letter B
Grade C : letter C
24
INTRODUCTION
Consumables Lubrications and Coolants [11922313]

Lubrications
The correct engine oil viscosity grade is dependent upon ambient temperature. Refer to the chart when selecting oil
for your tractor engine.
SS09J076 1
NOTE: In areas where prolonged periods of extreme temperatures are encountered, local lubricant practices are
acceptable; such as the use of SAE 5W-30 in extreme low temperatures or SAE 50 in extreme high temperatures.
Biodegradable Transmission and Hydraulic Oil

A biodegradable oil has been approved for use in the transmission, 4WD front axle and hubs, and the hydraulic system
of your tractor. Although the oil is 90% biodegradable, it is important to follow safe handling and disposal practices.
Biodegradable oil should not be used in conjunction with other oils. Use the following procedure to replace standard
oil with biodegradable lubricant.
1. Operate the tractor until the oil that is being changed reaches a temperature greater than 60 °C (140 °F).
2. Stop the engine and immediately drain the oil.
3. Replace all transmission and hydraulic filters.
4. Add the biodegradable oil to the correct level and run the tractor to circulate the oil.
5. Check for oil leaks and recheck the oil level.
Sulphur in Fuel
The engine oil and filter change period are shown in the Lubrication and Maintenance in the operators manual. How-
ever, locally available fuel may have a high sulphur content, in which case the engine oil and filter change period
should be adjusted as follows:
Sulphur Content % Oil Change Period

Below 0.5 Normal
From 0.5 - 1.0 Half the normal
Above 1.0 One quarter normal
NOTE: The use of fuel with a sulphur content above 1.3% is not recommended.
25
INTRODUCTION
Coolants
To reduce the amount of deposits and corrosion, the water used in the cooling system must comply with the following
values.
Total Hardness Chloride Sulphate

300 parts per million 100 parts per million 100 parts per million
Using Plain water

If you reside in a country where antifreeze is not available, use clean water premixed with 5% chemical inhibitor.
CAUTION
Inhibitor solution is irritating to eyes and skin . It contains buffered potassium hydroxide.
B084
• Avoid contact with eyes or prolonged or repeated skin contact.

• Wear protective eyewear when using.
• In case of contact with eyes, flush with water for 15 minutes and obtain medical attention.
• Wash skin with soap and water after use.
• Keep out of reach of children.
Lubrications and Coolant Specifications

CIH INTERNATIONAL
RECOMMENDED FLUIDS AND APPLICATIONS
SPECIFICATION SPECIFICATION
ENGINE OIL
AKCELA NO. 1 ENGINE OIL 15W-40 API CI-4,
MS 1121
AKCELA NO. 1 ENGINE OIL 10W-30 ACEA E7
TRANSMISSION, REAR AXLE AND HYDRAULIC
SYSTEM OIL
AKCELA NEXPLORE API GL4,
FRONT AXLE (Axle and Hubs) MAT 3525 ISO VG32/46,
AKCELA NEXPLORE M2C 134D
FRONT P.T.O GEARBOX OIL
AKCELA NEXPLORE
ENGINE RADIATOR COOLANT
AKCELA PREMIUM ANTI-FREEZE
MS 1710 Ethylene Glycol
(mixed with 50% of water)
BRAKE OIL
AKCELA LHM FLUID n/a ISO 7308
AIR CONDITIONING COMPRESSOR OIL
Low Viscosity Oil SP10 n/a PAG-E13, ISO100 Viscosity
GREASE FITTINGS AND BEARINGS
AKCELA MULTI-PURPOSE GREASE 251H EP 251H EP NLGI2, Li-Ca
Regarding filling quantity - see Capacities ()
26
INTRODUCTION
Capacities [16227161]
MAXXUM / MAXXUM Multicontroller
UNIT 100 110 120 130 115 125 140
176 l 250 l
FUEL TANK
(46.5 US gal) (66 US gal)
COOLING SYSTEM (with cab)
25 l (6.6 US gal)
*) only for North America
*23 l (6.1 US gal)
MAXXUM 100, 110 and 115
21 l 23 l
21 l
COOLING SYSTEM (less cab) n/a (5.5 US (6.1 US n/a
(5.5 US gal)
gal) gal)
ENGINE (including filter) 10 l (2.64 US gal) 15 l (3.96 US gal)
TRANSMISSION / REAR AXLE
58 l 58 l
(with 12x12, Light Duty axle) n/a n/a
(15.3 US gal) (15.3 US gal)
65 l 65 l
(with 12x12, Heavy Duty axle) n/a n/a
(17.2 US gal) (17.2 US gal)
58.5 l 58.5 l
(15.5 US gal) (15.5 US gal)
65.5 l 65.5 l
(with 24x24, Heavy Duty axle) n/a
(17.3 US gal) (17.3 US gal)
55.5 l 55.5 l
(14.7 US gal) (14.7 US gal)
62 l
(with 16x16, Heavy Duty axle)
(16.4 US gal)
4WD FRONT AXLE - 9l
DIFFERENTIAL (2.38 US gal)
4WD FRONT HUBS (Class 3 1.25 l
Axle - less breaks) 0.33 US gal)
4WD FRONT HUBS (Class 3 3l
Axle - with breaks) (0.79 US gal)
4WD FRONT HUBS (Class 4 3.6 l
Axle - less breaks) (0.95 US gal)
4WD FRONT HUBS (Class 4 4l
Axle - with breaks (1.06 US gal)
27
INTRODUCTION
28
SERVICE MANUAL
HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS

A
Contents
HYDRAULIC, PNEUMATIC, ELECTRICAL,

ELECTRONIC SYSTEMS - A
PRIMARY HYDRAULIC POWER SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.10.A

MAXXUM 100 , MAXXUM 110 Multicontroller , MAXXUM 110 , MAXXUM 115 Multicontroller , MAXXUM 115 , MAXXUM 120 Multicontroller
, MAXXUM 120 , MAXXUM 125 Multicontroller , MAXXUM 125 , MAXXUM 130 Multicontroller , MAXXUM 130 , MAXXUM 140
Multicontroller , MAXXUM 140
PRIMARY HYDRAULIC POWER SYSTEM Closed center mechanical remote valve . . . . . A.10.B
MAXXUM 100 , MAXXUM 110 , MAXXUM 115 , MAXXUM 120 , MAXXUM 125 , MAXXUM 130 , MAXXUM 140
PRIMARY HYDRAULIC POWER SYSTEM Electro-hydraulic remote valve . . . . . . . . . . . . . . . A.10.C

PRIMARY HYDRAULIC POWER SYSTEM Open center mechanical remote valve. . . . . . . A.10.D
MAXXUM 100 , MAXXUM 110 , MAXXUM 115 , MAXXUM 120 , MAXXUM 125 , MAXXUM 130 , MAXXUM 140
SECONDARY HYDRAULIC POWER SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.12.A

HYDRAULIC COMMAND SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.14.A

ELECTRICAL POWER SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.30.A

MAXXUM 100 , MAXXUM 110 Multicontroller [Z7BE50001 - Z9BE60000 ] , MAXXUM 110 , MAXXUM 115 Multicontroller [Z7BE50001 -
Z9BE60000 ] , MAXXUM 115 , MAXXUM 120 Multicontroller [Z7BE50001 - Z9BE60000 ] , MAXXUM 120 , MAXXUM 125 Multicontroller
[Z7BE50001 - Z9BE60000 ] , MAXXUM 125 , MAXXUM 130 Multicontroller [Z7BE50001 - Z9BE60000 ] , MAXXUM 130 , MAXXUM
140 Multicontroller [Z7BE50001 - Z9BE60000 ] , MAXXUM 140
ELECTRICAL POWER SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.30.A

MAXXUM 110 Multicontroller [Z9BE40001 - ] , MAXXUM 110 Multicontroller [Z9BE60001 - ] , MAXXUM 115 Multicontroller [Z9BE40001 - ] ,
MAXXUM 130 Multicontroller [Z9BE60001 - ] , MAXXUM 140 Multicontroller [Z9BE40001 - ] , MAXXUM 140 Multicontroller [Z9BE60001 - ]
ELECTRONIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.50.A

A
FAULT CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.50.A
A
A
HYDRAULIC, PNEUMATIC, ELECTRICAL,
ELECTRONIC SYSTEMS - A
PRIMARY HYDRAULIC POWER SYSTEM - 10.A

A.10.A / 1
Contents
HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC

SYSTEMS - A
PRIMARY HYDRAULIC POWER SYSTEM - 10.A
TECHNICAL DATA
PRIMARY HYDRAULIC POWER SYSTEM

Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Special tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Hydraulic pump
Fixed displacement pump - General specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Fixed displacement pump - Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Variable displacement pump - General specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Variable displacement pump - Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Charge pump
General specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
FUNCTIONAL DATA
PRIMARY HYDRAULIC POWER SYSTEM

Overview - Variable Displacement Pump High Pressure Hydraulic Circuit 16 x 16 Models. . . . . . . . . . . 10
Static description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Overview - Variable Displacement Pump High Pressure Hydraulic Circuit 24 x 24 Models. . . . . . . . . . . 37
Overview - Fixed Displacement Pump Hydraulic Circuit 12 x 12 and 24 x 24 Models . . . . . . . . . . . . . . . 41
Hydraulic schema . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Hydraulic schema (16x16 CCLS with Electronic Draft Control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Hydraulic schema (16x16 CCLS with Mechanical Draft Control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
MAXXUM 100, MAXXUM 110, MAXXUM 115, MAXXUM 120, MAXXUM 125, MAXXUM 130, MAXXUM 140
Hydraulic schema (24x24 CCLS with Electronic Draft Control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Hydraulic pump
Fixed displacement pump - Static description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Fixed displacement pump - Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Fixed displacement pump - Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Variable displacement pump - Static description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Variable displacement pump - Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Variable displacement pump - Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Variable displacement pump - Dynamic description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Variable displacement pump - Dynamic description (System description CCLS) . . . . . . . . . . . . . . . . . . . 66
Charge pump
A.10.A / 2
Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Compensator
Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
SERVICE
Hydraulic pump
Fixed displacement pump - Remove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Fixed displacement pump - Overhaul . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Fixed displacement pump - Visual inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Variable displacement pump - Remove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Variable displacement pump - Overhaul . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Variable displacement pump - Replace (Input shaft seal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Variable displacement pump - Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Variable displacement pump - Pressure test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Variable displacement pump - Flow test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Test (Air Ingress) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Charge pump
Overhaul . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Compensator
Overhaul . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
A.10.A / 3
HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - PRIMARY HYDRAULIC POWER SYSTEM
PRIMARY HYDRAULIC POWER SYSTEM - Torque [6426649]
BSE3603A 1
BRJ4969C 2
A.10.A / 4
PRIMARY HYDRAULIC POWER SYSTEM - Special tools [6426667]

DESCRIPTION PART NUMBER
Tee adaptor 11/16 ORFS female x 380000570*
11/16 ORFS male x 7/16 UNF female
Adaptor M10 banjo x 7/16 UNF 380000572*

female
Adaptor 7/16 UNF female x M12 x 380000577*
1.5p male
Adaptor 7/16 UNF male 380000999
Adaptor M14 banjo x M14 x 1.5p 380000579*
female
Tee adaptor 7/16 UNF female x 1/4 380000580*
BSP hose tail x 1/2 hose
7/16 UNF male Quick release adaptor 380000492
Adaptor M10 x 1.0p x 7/16 UNF 380000493
female
Hand pump 380000215
Lift relief valve fitting 380000217
90 quick release fitting with adaptor 380001146.
M8 x 1.0 male
Blanking Cap 11/16 ORFS 380000599*
Pressure Gauge 0–10 bar 380000551#
Pressure Gauge 0–27 bar 3800001145
Pressure Gauge 0–40 bar (5 off) 380000552#
Pressure Gauge 0–250 bar 380000553 #
Remote valve coupling 380000554#
Quick release adaptor 380000543
Pressure gauge hose 380000545#
1/8 NPT fitting to attach hose 292246 380000544#
to gauge
T–adaptor 13/16 ORFS female x 380000842.
13/16 ORFS male x 7/16 UNF female
Adaptor M10 x 1.0p x 7/16 JIC male 380000494
(enables use of gauges with 7/16 JIC
hoses if used)
diagnostic switch 380000488
Bypass connector 380001147.
Bypass connector 380000561
Trailer brake fitting 380000550#
Open Centre Lift Pressure Regulating 380000231
Valve Adjusting Tool
Flow Meter 120 l/min)
* Part of hydraulic adaptor kit
380000464
# Part of hydraulic pressure test kit
380000240
Remote valve check valve removal 380002720
tool
Charge pump pressure test adaptor 380200015
Lift ram pressure test tee piece 13/16 380200012
ORFS
Oil cooler pressure test adaptor 380200006
Hydraulic pump pressure test adaptor 380200090
Lube pressure test adaptor 380200091
A.10.A / 5
Hydraulic pump Fixed displacement pump - General specification

[6427344]
Filter
Type Full-flow, screw-on cartridge
Location Pump intake, on the R.H. side of the rear axle housing
PUMP
Type Gear type, with oil suction from transmission casing
Location On the R.H. side of the rear axle housing
Manufacturer BOSCH
Drive Driven by PTO input shaft
Corresponding rated output I/min 80
(US gallon/min) 21.1
Hydraulic pump Fixed displacement pump - Torque [6427391]
BVE0672A 1
A.10.A / 6
Hydraulic pump Variable displacement pump - General specification

[6429501]
Variable Displacement Piston Pump
Type
(Swash Plate Controlled)
Rotation Clockwise
Minimum Pump Speed 800 RPM
Maximum Pump Speed 2662 RPM
Pump Speed @ 2200 RPM (enginespeed) 2514 RPM
Displacement 45 cm³/rev (2.75 in³/rev)
113 l/min (24.9 UK gpm)
Output (new pump) @ 2200 RPM (enginespeed)
29.8 US gpm
23 bar +/- 1
Standby Pressure
( 334 psi +/- 14.5)
210 bar +/- 5
Maximum System Pressure
( 3045 psi +/- 72.5)
245 bar +/- 5
Spike Clipper Relief Valve
( 3553 psi +/- 72.5)
Peak Pressure 315 bar (4568 psi)
Hydraulic pump Variable displacement pump - Torque [6429483]
BSE3603A 1
A.10.A / 7
BRJ4969C 2
A.10.A / 8
Charge pump - General specification [6429604]

Type Rotor Pump
Displacement 57 cm³/rev (3.48 in³/rev)
143 l/min (31.5 UK gpm)
Output (new pump) @ 2200 RPM (enginespeed)
37.8 US gpm
Charge Pressure Filter Dump Valve Open @ 6 bar (87 psi)
Charge Pressure Limiting Valve Open @ 1.72 bar (24.9 psi)
Charge Pressure Switch (making charge pressure warning light flash) Close @ 0.55 - 0.82 bar (8 - 11.9 psi)
A.10.A / 9
PRIMARY HYDRAULIC POWER SYSTEM - Overview - Variable

Displacement Pump High Pressure Hydraulic Circuit 16 x 16
Models. [6433132]
A.10.A / 10
A.10.A / 11
Variable Displacement Pump High Pressure Hydraulic Circuit 16 x 16 Models
1 To Additional Remote Control Valves 2 End Plate With Pilot Line Pressure Reducing Valve and
Load Sensing Shuttle Valve
3 Variable Displacement Hydraulic Pump 4 Low Pressure Switch
5 Mid Mounted Remote Control Valve 6 Boosted Lubrication Oil
7 Front Suspension Control Valve 8 Trailer Brake Valve
9 Power Beyond Ports 10 Subplate with Low Pressure Compensator Valve
11 Feed to Low Pressure circuit 12 Lift Cylinder
13 Electronic Draft Control Valve 14 Electro-Hydraulic Remote Control Valve
A High Pressure Circuit Oil B Steering Circuit

C Low Pressure Circuit Oil D Trapped Oil
E Return To Reservoir Oil F Suction Oil
G Charge Pump Oil H Lubrication Oil
A.10.A / 12
BSF4140A 1
A.10.A / 13
A.10.A / 14
PRIMARY HYDRAULIC POWER SYSTEM - Static description

[1703160]
The hydraulic systems can be separated into the following circuits:-
High Pressure Circuit

Hydraulic Lift Assembly.
Remote Control Valves.
Trailer Brake (Where Fitted)

Suspended Front Axle.
Front Lift (Where fitted).
Steering Circuit
Steering Motor and Cylinders
Low Pressure Circuit

Independent Power Take Off (PTO).
Differential Lock
Front Wheel Drive engagement
Transmission clutch and synchroniser engagement
Creeper engagement (Where fitted)
Front PTO (Where fitted)
50 kph engagement (Where fitted)
Lubrication Circuit
PTO Clutch Plates
Transmission Clutch Plates.
Transmission Shaft Pressure Lube

Pump Drive Gear Bearing.
Hydraulic Lift Cross Shaft
The high pressure circuit is of the `Closed Centre Load Sensing' design on all tractor model options fed by either a
Variable Displacement Pump or a Fixed Displacement Pump.
The steering, low pressure and lubrication circuits are fed by a separate fixed displacement pump via a solenoid
activated lubrication block..
Hydraulic Pump/ HPL/ Remote Valve Options

Less Hydraulic Trailer Brakes With Hydraulic Trailer Brakes Hydraulic Trailer Brake Italy
Fixed Disp. Variable Disp. Fixed Disp. Variable Disp. Fixed Disp. Variable Disp.
MDC EDC MDC EDC MDC EDC MDC EDC MDC EDC MDC EDC
Remotes 2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4
12 x 12 Y Y Y Y Y Y
A.10.A / 15
24 x 24 Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y
16 x 16 Y Y Y Y Y Y Y Y Y Y Y Y
Before commencing work on a tractor it is important to identify if the tractor has a variable displacement pump or fixed
displacement pumps and the type of transmission.
Figure 1 shows the variable displacement pump with a 16 x 16 Transmission.
BSE3575A 1
Figure 2 shows the variable displacement pump with a 16 x 16 Transmission and ARGO hydraulic oil filter fitted to
later models..
BAIL07APH323ASA 2
Figure 3 shows the fixed displacement pump with a 24 x 24 Transmission.
BSE3665A 3
Closed centre remote valves (1) and Electronic draft control .
A.10.A / 16
BSE3604B 4
Tractors installed with the electronic draft control hydraulic lift assembly use a unique operator control panel.
(1). Draft sensitivity control knob
(2). Drop rate control knob
(3). Height limit control knob
(4). Slip limit control knob
BSE2884A 5
Maxxum Models with armrest unit from Serial No. Z9BE40001- and Z9BE60001-
BRL6436B 6
The lift arm position control is unique to tractors with electronic draft control.
.
(1). Stop adjuster thumbwheel
(2). Stop
(3). Position control lever
(4). Draft loading wheel
A.10.A / 17
(5). Raise/lower switch
BSE2892B 7
.
Maxxum Models with armrest unit from Serial No. Z9BE40001 and Z9BE60001
The raise and lowering functions of the electronic draft control lift system can also be operated from the rear fender
switch (1).
BRE1483B 8
The closed centre model tractors can also have electro-hydraulic remote valves (1).
BSE3604B 9
Located below the Electronic Draft Control valve (Where fitted), is the Hydraulic Power Tapping port (Power Beyond)
block. This includes a priority valve (1) and also a low pressure regulating valve. This block also has a flange plate
which allows the addition of a trailer brake valve.
A.10.A / 18
BSF3967A_430 10
Fixed Displacement high pressure hydraulic systems can be identified from the following:-
Fixed displacement pump.
BSE3572A 11
Mechanical remote control valves
BSE3664A 12
Located below the Electronic Draft Control valve (Where fitted), is the Hydraulic Power Tapping port (Power Beyond)
block. This includes a priority valve and also a low pressure regulating valve. This block also has a flange plate which
allows the addition of a trailer brake valve.
1. Power Beyond Ports

2. Pressure Relief Valve
A.10.A / 19
BSE3845A 13
The type of transmission installed can be identified by inspecting the transmission control lever.
Tractors with 16 x 16 transmission have a single control lever (1) with two shift buttons.
Closed centre hydraulic system only.
Figure [Invalid Reference] shows Semi-Powershift control lever..
BSE2889C_437 14
Maxxum Models with armrest unit from Serial No. Z9BE40001- and Z9BE60001-
BAIL09CCM793AVA 15
Tractors installed with 24 x 24 transmission uses two control levers. The main transmission lever (1) is provided with
push buttons (2) and (3) to actuate the Dual Command function.
These tractors can use either variable displacement pump or a fixed displacement pump.
A.10.A / 20
BSE3688A_438 16
Tractors installed with 12 x 12 Command transmission uses two control levers. These are the main shift lever (1) and
the range lever (2).
BSE3689A_439 17
A.10.A / 21
CLOSED CENTRE LOAD SENSING HIGH PRESSURE HYDRAULIC CIRCUIT
1b0o2004061057 18
High Pressure Circuit Components and Pipework
Tractors with Variable Flow Piston Pump
1 Remote and EDC Control Valves 2 Trailer Brake Valve

3 Load Sense Lines 4 Flow and Pressure Compensator Valve
5 Variable Flow Hydraulic Pump 6 Feed to Remote Valves
7 To Hydraulic Lift Ram 8 Feed to Electro-Hydraulic Valve Pilot Line
A.10.A / 22
The principal of operation of the closed centre load sensing high pressure hydraulic circuit with variable flow piston
pump is to supply oil flow on demand. It also enables simultaneous operation of the trailer brakes, hydraulic lift,
remote control valve assemblies and front axle suspension where fitted. The load sensing variable flow piston pump
offers significant benefits in reducing the engine power loss that occurs in open centre systems where a high volume
of oil, often far in excess of demand, is continuously pumped round the hydraulic circuit even when they are not being
operated.
A fixed displacement pump (Charge Pump) serves as an initial displacement pump for the variable displacement pump
. The variable displacement pump first of all supplies oil to the trailer brake valve (where fitted), the remote valves
and electronic draft control valve and a pilot oil supply with lower priority. The highest load pressure is indicated to
the flow and compensating valve on the pump via the load sensing line. The flow and compensator valve controls
the pump pressure in such a way that it always exceeds the highest load pressure by a pre-set difference. A priority
valve for low pressure circuit demand is located in the bottom subplate of the remote valve stack. Tractors fitted with
Electro-hydraulic remote valves also have high pressure oil supplied from the variable displacement pump to the top
plate of the remote valve stack. The oil passes through the top plate via a small filter and a pressure limiting valve (
20 - 22 Bar). The oil is then directed to the pilot oil supply of the electro-hydraulic control valve.
BSF4142A 19
Tractors with Variable Flow Piston Pump
1 End Plate 2 Load Sensing port for Mid Mount Valve

3 Electro-Hydraulic Remote Valves 4 Electronic Draft Control Valve
5 Trailer Brake Valve (Where Fitted) 6 Load Sensing Line
7 Low Pressure Circuit Distribution Manifold 8 Low Pressure Feed
9 Flow and Pressure Compensator Valve 10 Variable Displacement Pump
11 High Pressure Feed to Electro-Hydraulic Remote 12 Feed To Hydraulic Lift Cylinder
Valves
13 Feed to Italian type trailer brake solenoids 14 High Pressure Feed to Electro-Hydraulic Valve Pilot
Line
The high pressure circuit is illustrated in PRIMARY HYDRAULIC POWER SYSTEM - Overview (A.10.A).
A.10.A / 23
Hydraulic pump assembly.
Figure 20 shows the variable displacement pump assembly.

Integral with the high pressure variable displacement pump is the load sensing valve, containing the pressure and
flow compensating valves, the steering pump , the charge pressure and main system filters and various electrical
switches.
BSE3575A 20
Figure 21 shows the fixed displacement pump assembly.
BSE3572A_434 21
Load sensing valve assembly (1), consists of a flow compensating valve (2) and a high pressure control valve (3). The
load sensing valve receives hydraulic signals from operated components through the load sense line (4) and relays
this to the pump which will adjust to satisfy the system demands.
Figure 22 shows the load sense valve assembly.
BSE3660A 22
Steering pump,
The steering pump is a separate unit but still driven from the same drive gear as the main pump.
A.10.A / 24
BSE3662A 23
Trailer brake valve which is located beneath the cab just in front of the hydraulic lift assembly. The valve diverts oil
pressure to the trailer brakes whenever both tractor brake pedals are depressed.
BSE3599A 24
The hydraulic lift Electronic Draft Control Valve is a stack type design mounted together with the Remote Control
Valves (1) at the rear below the cab, and incorporates the safety valve for the lift cylinders
The lift cylinder safety valve protects the lift cylinder from shock loadings and limits the pressure in the cylinder to 210
- 215 bar
The hydraulic lift control valve is a proportional solenoid operated valve, controlled by a microprocessor, to raise and
lower the hydraulic lift.
BSE3604A 25
Closed centre load sensing remote control valves
There are two types of remote valves available for the closed centre system. Standard fitment are the mechanical
remote valves operated via a cable from within the cab and optional on all 16 x 16 models are electro hydraulically
operated valves, (1), Figure 26, which are operated by electrical switches and have their own in-built processor to
control oil flow via a solenoid valve.
Up to four mechanical type valves can be installed.
A.10.A / 25
BSE3604B 26
Hydraulic Lift Cylinders.
Models with mechanical draft control utilize a main lift cylinder which is located internally within the rear axle top cover
and also one or two 50 mm external cylinders depending on specification , Figure 27.
BSE3844A 27
Models with electronic draft control utilize two external cylinders, one per lift arm, anchored to the rear axle with a
bracket, Figure 28.
BSE3666A 28
Suspended front axle control valve.
Located on the right hand side of the tractor and attached to the rear axle centre housing. Receives high pressure
oil, via the trailer brake valve, if fitted, and with the use of processor controlled PWM valves controls oil to a cylinder,
attached between the front axle and front support, to provide a hydraulically controlled suspended front axle.
A.10.A / 26
BSE3668A 29
BAIL07APH357HSA 30
Front axle to front support hydraulic control cylinder (1).
BSE3769A 31
Hydraulic system filters.
Figure 32 shows the main hydraulic filter (1) for tractors fitted with 12 x 12 Transmission with mechanical draft control.
BSE3021A 32
Figure 33 shows the main hydraulic filters for tractors with fixed displacement hydraulic pump. this type of pump is
only fitted to tractors with 24 x 24 with mechanical draft control.
A.10.A / 27
BSE2928A 33
1. Intake Filter 2. Transmission Feed Pressure Filter
The main filter (3) and the charge filter (1) Figure 34 are only installed on tractors with variable displacement pump
(CCLS system).
BSE2755A 34
The main filter (1) and the charge filter (2) Figure 27 are installed on tractors with variable displacement pump (CCLS
system).
BAIS06CCM055AVA 35
1. Main Intake (Suction) Filter 2. Charge Filter
Mid-Mount Remote Valves.
Optional additional remote valves are mounted under the cab. Connected into the high pressure oil line supplied from
the hydraulic pump after the trailer brake valve and operated via a joystick control in the cab.
A.10.A / 28
BSE3576A_435 36
BAIL06CCM063ASA 37
High Pressure Hydraulic System, Fixed Displacement Pump - Electrical Switches
BSE3661A 38
1. Oil Temperature Switch 2. Intake Filter restriction (vacuum) Switch

3. Steering Pressure Switch
A.10.A / 29
High Pressure Hydraulic System, Variable Displacement Pump(CCLS) - Electrical Switches
BSE3573A 39
1. Intake Filter restriction (vacuum) Switch 2. Low Oil Temperature Switch

3. Low Charge Pressure Warning Switch
BAIL07APH325ASA 40
1. Low Charge Pressure Warning Switch 2. Intake Filter restriction (vacuum) Switch
3. Low Oil Temperature Switch
Steering Motor
All models use a fixed displacement motor.
BSD2178A 41
Steering Cylinders.
Receives high pressure oil directly from the steering motor.
A.10.A / 30
BSE2868B 42
Load Sensing Shuttle Valve.
Located in each remote valve slice, the Electronic Draft Control valve and between the trailer brake valve, front sus-
pension valve and mid-mounted valves, where fitted, is the load sensing shuttle valve (2). This allows the function
with the highest pressure demand to send sensing pressure to the load sensing valve, Figure 44, on the variable
displacement pump.
BSB0388A_436 43
1. Valve Body
2. Flow Compensating Valve
3. Pressure Compensator Valve
4. Load Sensing Line
BSE3660A 44
With Reference to PRIMARY HYDRAULIC POWER SYSTEM - Overview (A.10.A).
Operation of the closed centre high pressure hydraulic circuit is as follows:-

The components in the high pressure hydraulic circuit are connected by their load sensing lines to the hydraulic load
sensing valve which controls the output of the hydraulic pump.
A.10.A / 31
When the trailer brakes, remote control valves, hydraulic lift or front axle suspension (where fitted) are operating, the
load sensing valve on variable flow piston pump, compares the pressure in the component load sense line with the
output pressure of the hydraulic pump.
If pump output pressure is less than the combined pressure of the load sense line and spring force of the flow con-
trol valve, then pump output continues to increase. When circuit demand is satisfied pump pressure overcomes the
combined pressure of the load sense line and flow compensating valve spring. This moves the spool in the flow com-
pensating valve to the right, allowing control pressure oil to be directed to the variable flow swash plate servo piston,
which de-strokes the pump to adjust output to circuit demand.
For a detailed explanation on the load sensing operating principle of the variable flow piston pump refer to Hydraulic
pump Fixed displacement pump - Static description (A.10.A).
High Pressure oil is fed to a subplate at the bottom of the remote valve stack where it is directed to the Trailer Brake
valve which has priority for safety reasons. The oil is then redirected to the Electronic Draft Control Valve and the
Electro-Hydraulic Remote Valves. Within the subplate is a pressure compensating valve which diverts the oil to the
low pressure system at a pressure of 17 - 18 bar.
High Pressure oil is also fed to the top of the Remote Valve stack through an end plate which incorporates a pressure
limiting valve and this supplies oil at 20 - 22 bar to the pilot line galleries in the Electro-Hydraulic Remote Valves.
Surplus oil from the charge pump to the variable displacement pump is fed past the 0.8 bar valve and boosts the
pressure in the lubrication circuit.
Refer to PRIMARY HYDRAULIC POWER SYSTEM - Overview (A.10.A).
FIXED DISPLACEMENT HIGH PRESSURE HYDRAULIC CIRCUIT
BSE3806A 45
Tractors with Mechanical Hydraulic Lift and Fixed Displacement Hydraulic Pump
1 Remote Control Valves 2 Feed To Mechanical Draft Control Valve

3 Mechanical Draft Control Valve 4 Steering Pump (Steering Circuit)
5 High Pressure Circuit Gear Pump 6 Hose To Pressure Relief Valve
A.10.A / 32
7 Feed To Lift Cylinder 8 Pressure Relief Valve( 195 - 205 Bar)

9 High Pressure Feed To Remote Valve Stack
On high pressure hydraulic systems with fixed displacement pump, all components are connected in series and pump
flow is continually circulating through the hydraulic system even when the circuits are not being operated.
The priority of operation is given to the order of components in the circuits, that is trailer brakes, remote valves and
hydraulic lift.
The high pressure hydraulic circuits for tractors installed with mechanically controlled hydraulic lift are shown in Fig-
ures 52 and include the components shown on the following pages.
Fixed displacement hydraulic pump assembly comprising of the high pressure gear pump and steering/low pressure
gear pump .
BSE3572A_440 46
High pressure circuit relief valve (1) located on the right hand side of the top cover diverts pump flow to sump if the
system pressure reaches 190 bar ( 2755 lbf/in2).
BSF4290A 47
The trailer brake valve is located beneath the cab on top of the hydraulic lift cover. The valve diverts oil pressure to
the trailer brakes whenever the right hand tractor brake pedals is depressed. This is unlike the valve installed on the
closed centre system where both pedals have to be depressed in order for the valve to operate.
The trailer brake has absolute priority over other services in the circuit.
A.10.A / 33
BSE3599A_441 48
The remote valves are available as two, three or four valves per tractor.
The valves can be double-acting with float and kick out.
Double acting convertible to single-acting with float.
Double acting convertible to single-acting.

When four remote valves are installed the optional flow divider valve (1) is available enabling simultaneous operation
of remote valve No 1 with another remote valve or hydraulic lift.
BSE3664A_442 49
On tractors which are fitted with mechanical hydraulic lift, the lift cylinder control valve (1) assembly is located at the
front of the hydraulic lift assembly. The lift cylinder safety valve is mounted on the rear face of the control valve which
must be removed to obtain access. This safety valve will operate at between 210 - 215 Bar.
BSF3981A 50
The low pressure regulating valve is located in the top manifold situated on the lubrication services distribution block
on the left hand side of the rear axle centre housing. This valve regulates the pressure in the low pressure circuit to
17 - 18 bar ( 246 - 261 lbf/in2).
Also located in this manifold are the oil cooler by-pass valve and the lubrication relief valve ( 7.3 - 8.3 bar).
When the oil is cold and pressure differential across the oil cooler is higher than 6 bar ( 87 lbf/in2) the cooler by-pass
valve (1) located on the right hand side of the transmission will operate to ensure that adequate flow to the lubrication
A.10.A / 34
circuit is maintained. This feature of diverting oil from the cooler assists in aiding a rapid warm up of oil in cold weather
conditions.
The steering pump / steering return oil is directed through the oil cooler at the front of the tractor and is limited to a
maximum pressure of 7 bar ( 101 lbf/in2) by the lubrication relief valve located in the lubrication services distribution
block on the left hand side of the rear axle centre housing.
BSE3775B 51
High Pressure Circuit for Tractors with Fixed Displacement Pump and Mechanical Hydraulic Lift
With Reference to Figure 52.
Both the high and low pressure pumps are driven by a `live' drive gear train directly connected to the PTO clutch input
drive shaft and driven by the engine flywheel.
Oil is drawn through the common intake port and filter to both the high and steering/low pressure pump assemblies.
The high pressure pump supplies constant oil flow according to engine speed, through the trailer brake and remote
valves via a subplate at the bottom of the remote valve stack. The subplate incorporates a flow control valve which
limits the maximum operating pressure.
Oil, after passing through the remote valves, enters the hydraulic lift control valve located at the front of the lift as-
sembly, which controls the raising and lowering of the lift.
All excess oil flow produced by the hydraulic pump is returned direct to the rear axle through the control valve spool
located in the hydraulic lift control valve assembly.
Also located within the assembly is the lift cylinder safety valve, which protects the lift cylinder and seals from exces-
sive peaks of pressure during operation.
For further details on operation of the mechanical hydraulic lift assembly, trailer brake valve and mechanical remote
refer to the appropriate Chapters in this Section of the Repair Manual :
HITCH Electronic draft control - Static description (H.10.D) (MECH LIFT),
Trailer brake valve - Static description (D.34.C) (TBV),
PRIMARY HYDRAULIC POWER SYSTEM Closed center mechanical remote valve - Static description (A.10.B)
(MECH REMOTES).
A.10.A / 35
BSF4116A 52
Fixed Displacement Pump High Pressure Hydraulic Circuit Operation
Tractors With Mechanical Hydraulic Lift
Hydraulic Lift Operating
Steering System System Pressure Trapped Oil

Oil Oil
Low Pressure Return to Lubrication Oil
Circuit Oil 17 - 18 Reservoir Oil
bar ( 246 - 261
lbf/in²)
Suction Oil
1. Lift Control Valve 2. Lift Cylinder Safety Valve

3. Mechanical Hydraulic Lift Assembly 4. Steering Motor
5. Low Pressure Circuit Pressure Regulating Valve 6. Steering and Low Pressure Circuit Gear Pump
7. Fixed Displacement Pump 8. Pressure Relief Valve ( 195 - 205 Bar)
9. Subplate with Pressure Compensator 10. Trailer Brake Valve
A.10.A / 36
PRIMARY HYDRAULIC POWER SYSTEM - Overview - Variable

Displacement Pump High Pressure Hydraulic Circuit 24 x 24
Models. [6438849]
A.10.A / 37
Variable Displacement Pump Closed Centre Load Sensing Hydraulic Circuit 24 x 24 Models
1 To Additional Remote Control Valves 2 End Plate With Load Sensing Shuttle Valve
3 Variable Displacement Hydraulic Pump 4 Mid Mounted Remote Control Valve
5 Low Pressure Switch 6 Boosted Lubrication Oil
7 Front Suspension Control Valve 8 Trailer Brake Valve
9 Power Beyond Ports 10 Subplate with Low Pressure Compensator Valve
11 Feed to Low Pressure circuit 12 Lift Cylinder
13 Electronic Draft Control Valve 14 Remote Control Valve
A High Pressure Circuit Oil B Steering Circuit

C Low Pressure Circuit Oil D Trapped Oil
E Return To Reservoir Oil F Suction Oil
G Charge Pump Oil H Lubrication Oil
A.10.A / 38
Hydraulic pump Fixed displacement pump - Static description

[1703079]
The hydraulic pumps are a gear type and fixed displacement according to ERPM.
The hydraulic pumps are mounted on the right hand side of the rear axle housing and are driven from gears splined
directly to the PTO drive shaft. Oil is supplied to the hydraulic pumps from the rear axle housing, via a common intake
filter.
The front hydraulic pump controls hydrostatic steering, front and rear differential locks, PTO and PTO brake, and four
wheel drive engagement.
The rear hydraulic pump supplies oil for the hydraulic lift, trailer brake valve, and remote control valves.
A.10.A / 57
Hydraulic pump Fixed displacement pump - Overview [1701595]
BVE0673A 1
Hydraulic Pump Assembly With Fixed Displacement Closed Centre System
1 Hydraulic lift system oil pump 2 Steering / low pressure oil pump
3 Main intake filter restriction (vacuum) switch 4 Main intake filter
5 Low oil temperature switch
A.10.A / 58
Hydraulic pump Fixed displacement pump - Exploded view

[1701819]
BSD2033A 1
Hydraulic Lift System Oil Pump Exploded View
1 Bearing Block 2 Oil Seal

3 Plastic Back-up Seal 4 O-ring Seal
5 Pump Housing 6 O-ring Seal
7 End Plate 8 Retaining Bolts
9 Drive Gears 10 Bearing Block
11 Oil Seal 12 Plastic Back-up Seal
13 End Plate
A.10.A / 59
Hydraulic pump Variable displacement pump - Static description

[6440386]
The variable flow closed centre load sensing hydraulic pump assembly is mounted on the right hand side of the rear
axle centre housing and contains within its body two hydraulic pumps.
• A charge pump of the gear type to supply oil at a charge pressure of 3 bar (44 psi) to a variable flow closed
centre load sensing hydraulic piston pump.
• A variable flow closed centre load sensing piston type hydraulic pump supplying oil to the high pressure circuits
for operation of:
Trailer Brake
Hydraulic Lift Assembly
Remote Control Valves
Front Axle Suspension
Front Lift
Mid Mount remote valves
A.10.A / 60
Hydraulic pump Variable displacement pump - Overview [13064140]
BSE3602A 1
1 Load Sensing Valve assembly 2 Steering Pump

Supplementary Lube valve and By-pass
3 4 Main Intake Filter restriction (vacuum) Switch
Valve
5 Main Filter 6 Low Oil Temperature Switch
Variable Displacement Pump and Charge
7 8 Charge Pump Filter
Pump
9 Low Charge Pressure Warning Switch 10 Main System Relief Valve 245 bar (3553 psi)
11 Pressure Feed to Remote Valve Block
A.10.A / 61
Hydraulic pump Variable displacement pump - Exploded view

[1701793]
BSE3588A 1
Variable Flow Piston Pump Components
1 Rod 2 Piston
3 Ò' Ring 4 Plug
5 Seal 6 Bearing
7 Shim 8 Shaft
9 Bearing 10 Valve Plate
11 Snap Ring 12 Spring
13 Seal 14 Pins
15 Rotor Cylinder 16 Cone
17 Plate 18 Pistons
19 Swash Plate 20 Thrust Bearing
21 Spring
A.10.A / 62
Hydraulic pump Variable displacement pump - Dynamic description

[13064219]
Principal of Operation
Both pumping elements are driven by a `live' drive gear train directly connected to the PTO clutch input drive shaft
and driven by the engine flywheel.
The operating principal of the fixed displacement gear pump is to provide a constant oil flow directly related to the
rotation speed of the pump
The operating principal of a variable flow piston pump is to provide oil flow on demand and minimises the engine
power absorbed in driving the hydraulic pump when the hydraulic circuits do not require maximum pump flow.
The variable flow piston pump in hydraulic systems therefore has distinct power loss advantages over fixed displace-
ment gear type pumps, which continually provide oil flow and absorb engine power even when the hydraulic circuits
do not require the total pump output.
BSD2188A 1
Variable Displacement Piston Pump - Sectional Drawing
1 Stroke control piston 2 Rod

3 Swash plate return spring 4 Driveshaft
5 Swash plate 6 Slipper (9 off)
7 Piston and barrel (9 off) 8 Inlet port
9 Shaft pre-load spring 10 Outlet port
A.10.A / 63
The major components of the variable flow piston pump with closed centre load sensing
are:
• A nine element pumping head.
• A plate mechanism (swash plate) to adjust piston stroke and corresponding pump output.
• A load sensing valve which monitors the requirements of the hydraulic circuits and signals the pump to increase
or decrease hydraulic oil flow accordingly.
The nine element pumping head is cylindrical in shape and has nine barrels, into each of which, is installed a piston.
On the end of each piston is pressed a slipper which always remains in contact with the face of the swash plate located
at the front of the pumping head.
The drive shaft, which is driven by the pump drive gear, rotates the pumping head. As the pumping head rotates, the
pistons move in and out of their barrels, following the contour of the swash plate. For every revolution of the drive
shaft each piston completes one pumping cycle.
The swash plate, which does not rotate but pivots about the front of the pumping head, is the control mechanism that
limits the stroke of each piston and works in conjunction with the pressure and flow compensating valves in the load
sensing line.
As the pumping head rotates each barrel passes over the inlet and then the outlet ports of the pump. During the inlet
cycle for each piston and barrel, oil is pumped into the barrel pushing the piston forward so that it always remains in
contact with the swash plate. The stroke of each piston and volume of oil charged into its barrel is therefore dependent
on the angle of the swash plate.
After a piston and barrel has completed the inlet stroke, further rotation of the head aligns the barrel with the outlet
port. Oil within the barrel is then forcibly ejected by the piston through the exhaust port to the hydraulic circuits.
BSE3585A 2
Variable Displacement Hydraulic Pump Installation
1 Trailer Brake Valve Assembly 2 Load Sensing Line

3 Flow and Compensator Valve 4 Steering Pump
5 Filter Restriction Vacuum Switch 6 Main Intake Filter
7 Low Oil Temperature Switch 8 Charge Pressure Filter
9 Variable Displacement Pump
A.10.A / 64
The location of the principal components in the hydraulic pump assembly are identified above. These items are shown
on the hydraulic circuit diagrams which describe the operating modes of the pump. The principal function of the valves
and switches is as follows:
Intake Filter and Restriction Switch

Oil for both the charge and steering pump is drawn from the rear axle centre housing via the intake filter. The filter
incorporates a by-pass valve, which is an integral part of the replaceable filter and it is therefore essential that the
correct filter is installed at every filter change.
When the filter is blocked the oil filter restriction vacuum switch is activated and illuminates the oil filter restriction
warning light on the instrument panel.
Because oil is more viscous (thicker) when cold and can falsely indicate that the filter requires servicing a low temper-
ature oil switch is also used in the filter restriction circuit. This switch ensures that the warning light will not operate
if the oil temperature is less than 40 °C (104 °F).
Low Charge Pressure Switch

The low charge pressure switch will cause a light to `Flash' on the instrument cluster whenever the charge pressure
is less than 0.75 bar (10.9 psi).
Charge Pressure Filter Dump Valve

The charge pressure filter dump valve is a safety relief valve for relieving excess pressure on the charge pump should
the filter be restricted. This valve will start to operate if the charge pressure exceeds 6 bar (87 psi).
Charge Pressure Valve

The charge pressure valve diverts excess oil supplied by the charge pump and not required by the variable flow piston
pump to the inlet port of the steering and lubrication circuit pump.
This valve starts to operate at a pressure of 1 bar (14.5 psi)and when fully open limits the charge pressure circuit oil
to 3 bar (43.5 psi).
Flow and Pressure Compensating Valves

Output from the variable flow piston pump is determined by adjusting the angle of the swash plate in the pump. The
flow compensating valve senses the circuit operating pressure and adjusts the swash plate angle to control pump
output.
If pump output and circuit pressure rises to 205 bar (2973 psi) the pressure compensating valve overrides the flow
compensating valve and adjusts the swash plate angle to limit maximum system pressure.
A.10.A / 65
Hydraulic pump Variable displacement pump - Dynamic description

(System description CCLS) [13064269]
The charge pressure pump draws oil through the charge pump inlet filter.
Oil drawn by the charge pump flows through the charge pressure filter to the variable flow piston pump and also
through the charge pressure valve to the inlet port of the steering pump.
Because output from the charge pump can exceed the combined demand of the steering and variable displacement
pumps an open gallery between the inlet side of the charge and steering pumps allows excess flow to the inlet side
of the steering.
The variable flow closed centre load sensing hydraulic pump operates progressively in 5 modes:
• Generating Low Pressure Standby pressure
• Low Pressure Standby
• High Pressure Circuit Maximum Demand
• High Pressure Circuit Low Demand
• Maximum System Pressure (High Pressure Standby)
1 Electro Hydraulic Remote (EHR) Valve 2 Low Pressure Pilot Line for EHR Control Spool
3 Load Sensing Line from EHR Valve 4 Electronic Draft Control (EDC) Valve
5 Load Sensing Line from EDC Valve 6 Lift Ram
7 Load Sensing Line from Trailer Brake Valve 8 Load Sensing Shuttle Valves
9 Flow Compensating Valve 22 bar (319 psi) 10 Pressure Compensating Valve 205 bar (2973
psi)
11 Variable Displacement Pump Assembly 12 Low Charge Pressure Warning Switch
13 Steering System Supply oil 14 Steering Pump
15 Charge Pressure Bypass Valve 3 bar (44 psi) 16 Supplementary lube valve 0.8 bar (12 psi)
17 Main Intake Filter Vacuum Switch 18 Main Intake Filter
19 Low Temperature Switch 40 °C (104 °F) 20 Charge Pump
21 Charge Pressure Filter 22 Charge Pressure Filter Dump Valve 6 bar (87
psi)
23 Main System Relief Valve 245 bar (3553 psi) 24 Trailer Brake Valve Outlet
25 Low Pressure Regulating Valve 26 Low Pressure Relief Valve 30 bar (435 psi)
27 Trailer Brake Valve 28 Low Pressure Regulating Valve Assembly
29 End Plate with Pressure Regulator Valve for 30 High Pressure Supply to Front Suspension or
Supply to EHR Pilot Line 20 - 22 bar (290 - Mid Mount Remotes, where fitted
319 psi)
31 Low pressure Supply to Transmission
clutches, Four Wheel Drive, Differential
Locks, PTO clutch and PTO Brake
A Load Sensing Line from High pressure circuit B Return to Reservoir from flow and pressure
components compensating valves.
C Gallery to Swash Plate servo piston from flow D System Pressure sensing gallery to flow and
and compensating valves pressure compensating valves
E System pressure supply to low pressure F Regulated Low pressure oil supply
regulating valve
G System pressure outlet from low pressure H Low pressure regulating valve spool sensing
regulating valve gallery
A.10.A / 66
BSF4141F 1
A.10.A / 67
Generating Low Pressure Standby

Low pressure standby is the system pressure 21 bar (305 psi), maintained by the hydraulic pump when high pressure
hydraulic circuits are not being operated.
Control of the swash plate, which regulates the output of the variable displacement piston pump, is achieved by the
flow and pressure compensating valves located on the top of the pump.
When the engine is first started, the swash plate return spring positions the swash plate for maximum output of the
pump. During engine start up, Low Standby Pressure has not yet been generated by the pump and the flow compen-
sating valve spool is held to the right by spring pressure. The position of the spool prevents oil pressure generated
by the pump, being applied through gallery D to the swash plate servo piston through gallery "C". The swash plate
consequently remains in the maximum flow position until the piston pump has developed standby pressure.
psi)
psi)
319 psi)
System Pressure 205 bar (2973 psi) Return To Reservoir
Standby Pressure 22 bar (319 psi) Steering Circuit
Control Pressure Low Pressure 17 bar (247 psi)
Charge Pressure 3 bar (44 psi) Trapped Oil
Suction Lubrication Oil
A.10.A / 68
BSF4141A 2
A.10.A / 69
Regulating Low Pressure Standby

When the pressure in the system is below 17 bar (247 psi) the Low-Pressure Priority valve is held by the spring to
give flow priority to the low-pressure systems.
As the pressure in the system increases to 17 bar (247 psi) the Low-Pressure Priority valve is moved against the
spring, by the pressure sensed through the orifice, to allow increased flow to the high pressure systems and regulates
the pressure in the low pressure system.
As system pressure continues increases to 22 bar (319 psi), known as Low Standby Pressure, the increase in pres-
sure is sensed in gallery D and applied to the end of the flow compensator spool. The spool gradually moves against
the spring allowing oil flow from gallery D to gallery C, Figure 3.
The controlled pressure rise in gallery C operates the swash plate servo piston, changing the angle of the swash plate
in relation to the pumping head. The change in angle reduces the operating stroke of the pistons and output of the
pump.
As pump output decreases and the pressure in gallery D reduces to less than 22 bar (319 psi), the spring in the flow
compensating valve gradually moves the spool to the left opening gallery C to sump through gallery B, via the spring
cavity of the pressure compensating valve. This reduces the pressure applied to the servo piston, allowing the servo
piston to retract at a controlled rate under pressure from the swash plate return spring, which re-adjusts the angle of
the swash plate to increase pump output.
This process where the flow compensating valve spool moves back and forth to control the pressure applied to the
servo piston, continues until there is a demand by the hydraulic system to increase output to operate the hydraulic lift,
remote control valves, front axle suspension (where fitted) or trailer brakes (where fitted).
psi)
psi)
319 psi)
A.10.A / 70
BSF4141B(R) 3
A.10.A / 71
High Pressure circuit High Demand

After the pump has reached standby pressure and one of the high pressure services is operated, the pressure rise in
the hydraulic circuit being operated is sensed by the load sensing line A.
The pressure in the sensing line is now applied to the spring loaded end of the flow compensator valve.
The combined pressure from the pilot line and flow compensating valve return spring causes the flow compensating
spool to move against the standby pressure in gallery D, preventing the flow of oil to the swash plate servo piston
through gallery C.
The movement of the spool opens gallery C to the return to sump gallery B, allowing the servo piston to retract under
pressure from the swash plate return spring, which re-adjusts the angle of the swash plate to increase pump output.
As the pressure in the system increases the Low Pressure Priority Valve works against the spring to regulate the low
pressure system to 17 bar (247 psi).
psi)
psi)
319 psi)
A.10.A / 72
BSF4141C 4
A.10.A / 73
High Pressure circuit Low Demand

As pump output increases so does the system pressure generated and applied to the end of the flow compensating
spool through gallery D.
When the hydraulic operating cycle nears completion, eg. the hydraulic lift is raised out of the ground and the main
spool in the electronic draft control valve gradually returns to the neutral position, the pressure in the load sensing line
similarly begins to decrease. When the pressure generated in gallery D is 22 bar (319 psi) greater than that in the
load sensing gallery A the flow compensator spool moves back against the spring to open gallery D to gallery C. The
controlled pressure rise in gallery C now operates the swash plate servo piston and changes the swash plate angle
to reduce pump output and the speed of lift.
It can now be seen that the basic principle of pump control, when operating the hydraulic high pressure circuits, is
similar to that for operation of the pump at standby pressure when there is no high pressure hydraulic demand. The
only difference is that because the pressure in the hydraulic system circuit being operated is sensed through the load
sensing line A, the pressure required to operate the flow compensating valve is higher than that for standby pressure
operation.
The Low-Pressure Priority Valve will continue to sense the changes in system pressure to regulate the low-pressure
system to 17 bar (247 psi).
psi)
psi)
319 psi)
A.10.A / 74
BSF4141D 5
A.10.A / 75
Limiting Maximum System Pressure

To limit the maximum output pressure of the piston pump under normal operating conditions, a pressure compensating
valve, located adjacent to the flow compensator valve, is incorporated in the swash plate control circuit. This valve
limits the pressure to 190 bar (2755 psi) and operates as follows:
As the pressure in gallery D increases to 205 bar (2973 psi) the pressure compensator valve spool moves against
the valve return spring and opens gallery D to gallery C. The pressure in gallery D is now applied to the servo piston
which changes the swash plate angle to reduce pump output to minimum flow. This operating mode is referred to as
high pressure standby.
If the pressure in gallery D for some reason exceeds the setting of the pressure compensating valve there is a system
safety valve set to 245 bar (3553 psi) to prevent consequential damage that may occur due to excessive pressures.
The Low-Pressure Priority Valve will continue to sense the changes in system pressure to regulate the low-pressure
system to 17 bar (247 psi).
psi)
psi)
319 psi)
A.10.A / 76
BSF4141E 6
A.10.A / 77
Charge pump - Exploded view [1701872]
BSE3587A_457 1
Charge Pump Components
1 End Plate 2 Seal

3 Coupling 4 Shaft
5 Rotor Housing 6 Charge Pump Housing
7 Seal 8 Pin
9 Hub 10 Screw Plug
11 System Relief Valve ( 245 bar (3552.5 psi)) 12 Check Valve Plug
13 Seal 14 Check Valve Spool
15 Main Charge Filter 16 Pump Rotor
17 Key 18 Screws
A.10.A / 78
BAIL07APH346FSA 2
Charge Pump Components
1 End Plate 2 Seal

3 Coupling 4 Shaft
5 Rotor Housing 6 Charge Pump Housing
7 Seal 8 Pin
9 Hub 10 Screw Plug
11 System Relief Valve ( 245 bar (3552.5 psi)) 12 Check Valve Plug
13 Seal 14 Check Valve Spool
15 Main Charge Filter 16 Pump Rotor
17 Key 18 Screws
A.10.A / 79
Compensator - Exploded view [1701904]
BSE3586A_454 1
Flow and Pressure Compensating Valves
1 Plug 2 Seal
3 Disc 4 Spring
5 Spring 6 Seat
7 Housing 8 Screw
9 Spool 10 Snap-ring
11 Plug 12 Plug
13 Seal 14 Seal
15 Damper Screw 16 Nozzle
17 Seat 18 Spring
19 Spring 20 Disc
21 Seal 22 Plug
23 Nut 24 Screw
25 Locknut
A.10.A / 80
Hydraulic pump Fixed displacement pump - Remove [1704224]

Prior operation:
Remove the battery cover and disconnect the battery negative cable (refer to Battery - Disconnect (A.30.A)).
Prior operation:
Raise the rear of the tractor, place an axle stand under the right hand side final drive case and remove the right hand
side rear wheel (refer to Rear wheel - Remove (D.50.C)).
Prior operation:
Remove the drain plug and drain oil into a suitable container.
Install the drain plug after the oil has drained (refer to REAR AXLE - Drain fluid (D.12.A)).
WARNING
Handle all parts carefully. Do not put your hands or fingers between parts. Wear suitable safety clothing -
safety goggles, gloves and shoes.
B026
1. Using a suitable filter strap, remove the oil filter (1).
BVE0444A 1
2. Disconnect the low oil temperature switch electrical

connector (1) and the main intake filter restriction
switch electrical connector (2).
Cut the cable tie and reposition the wiring harness.
BVE0445A 2
A.10.A / 81
3. Remove the steering / low pressure oil pump oil sup-

ply pipe.
BVE0446A 3
4. Remove the hydraulic lift system oil pump oil supply

pipe.
BVE0449A 4
5. Remove the main oil supply pipe lower retaining bolt

(1).
BVE0450A 5
6. Remove the oil supply manifold retaining nuts.
BVE0451A 6
A.10.A / 82
7. Remove the oil supply manifold (1) and the main oil
supply pipe (2) as an assembly.
BVE0452A 7
8. Detach the hydraulic lift system oil pump supply pipe.
BVE0453A 8
9. Remove the hydraulic lift system oil pump.
BVE0454A 9
A.10.A / 83
Hydraulic pump Fixed displacement pump - Overhaul [1705390]
WARNING
Handle all parts carefully. Do not put your hands or fingers between parts. Wear suitable safety clothing -
safety goggles, gloves and shoes.
B026
1. Install new oil seals and O-rings. When installing

oil seals in the bearing block ensure that the plas-
tic back-up seal (1) is correctly positioned in the rub-
ber seal (2). Hydraulic pump Fixed displacement
pump - Exploded view (A.10.A).
TIA35012 1
2. Install the driveshaft and driven gears into the hy-

draulic pump body, ensuring that the identification
marks (1) face in the same direction.
BVE0680A 2
3. Tighten the retaining bolts to the specified torque

value.
BVE0674A 3
A.10.A / 84
Hydraulic pump Fixed displacement pump - Visual inspection

[1705659]
1. Wash all components using a suitable degreaser.
2. Inspect the O-ring seal groove and the shaft oil seal
recess in the mounting flange, these should be un-
damaged and free from burrs.
3. Examine the gears, shafts, and bearing blocks for
wear. The pump must be renewed if:
4. The PTFE coated bearings (1) in the bearing blocks
are worn through revealing the bronze backing.
The gear side faces are scored. This concern is often
caused by contaminated oil.
There is a distinctive wear step on the side faces of
the gears and bearing blocks.
BVE0681A 1
5. IMPORTANT: When servicing the pump gears, par-

ticular attention must be paid to the following points:
The width of each gear set must be within 0.005 mm (
0.0002 in.) of each other to ensure satisfactory pump
efficiency.
6. Journals must be within 0.013 mm ( 0.0005 in.) of
each other.
7. Gear faces must be flat. This feature may be
checked using engineers blue on the bearing face
and rotating against the gear. This check will also
reveal any sharp edges on the teeth.
A.10.A / 85
Hydraulic pump Variable displacement pump - Remove [15215706]
Prior operation:
Remove the right hand rear wheel - see Rear wheel - Remove (D.50.C).
NOTE: The hydraulic pump is a heavy component and weighs 30 kg (66 lb). It is important that it is securely supported
when being removed from the tractor.
NOTE: If oil is not drained from transmission, do not remove tube from sump at sump end otherwise oil spillage will
occur.
NOTE: To prevent excessive loss of oil loosen intake filter by approximately one turn and leave for one minute to
allow oil in filter to drain into sump.
1. Drain oil into a suitable container.
2. Remove charge filter (1) by unscrewing anti-clock-
wise.
Remove the intake filter (3) by removing the retaining
bolts (2).
BSE2755A_455 1
3. Disconnect all electrical and hydraulic connections to

pump.
NOTE: Loosen the oil filter vent cap and leave for one
minute to allow oil in the filters to drain into the sump.
BAIS06CCM055AVB 2
Remove filter retaining bolts.
BAIL08CVT263AVA 3
A.10.A / 86
4. Ensure lubrication pipe banjo connector and brake

line retaining bracket are disconnected from pump
body.
5. Remove filter housing and related tubes and elbows
including the supplementary lube valve.
6. Undo pump retaining nuts and remove pump.
BSD2052A 4
Next operation:
Charge pump - Overhaul (A.10.A)
A.10.A / 87
Hydraulic pump Variable displacement pump - Overhaul [15223572]

Hydraulic pump Variable displacement pump - Exploded view (A.10.A)
Prior operation:
Hydraulic pump Variable displacement pump - Remove (A.10.A)
1. Remove pressure and flow compensating valves as-

sembly.
BSD2023A 1
2. Undo the 4 retaining bolts and remove circlip from

opposite end of pump. Gently remove charge Pump
from main pump assembly.
BSD2051A 2
3. Examine valve plate (1). Check to see if it is scored,

nicked, warped or damaged by cavitation. Look for
score marks or damage around the bearing surface
area. Check the inlet and discharge port area for
signs of contamination. This contamination may
show as grooves starting in the feathering notch.
BSD2025A 3
A.10.A / 88
4. Remove bearing cone (1) and splined connector.
70-421-491 4
5. Remove preload spacer from driveshaft. Remove

pumping head and piston from housing. Using a suit-
able marker identify each piston and slipper to their
corresponding barrel in the pumping head.
TIA35167 5
Pumping Head and Slipper Assembly

6. Separate pumping head and slipper assembly and
inspect for damage. Where damage is identified the
pumping element must be replaced.
1 Pistons and Slippers
2 Cone
3 Washer
4 Pumping Head
5 Pins (3 off)
TIA35168 6
A.10.A / 89
Pumping Head Spring Assembly

7. If necessary disassemble pumping head spring as-
sembly by compressing the collar against the spring.
1 Pumping Head
2 Washer
3 Spring
4 Collar
5 Retaining Ring
NOTICE: Due to high spring pressure take care when re-
moving retaining ring.
TIA35169 7
8. Remove swash plate (1) assembly.
70-421-461 8
9. Inspect components for wear and replace if dam-

aged.
Pump Reassembly
10. Before reassembling the load sensed variable dis-
placement pump, replace all worn and damaged
parts and assemblies and all seals and O rings.
Lubricate the seals and O rings with petroleum jelly
to retain them during reassembly and provide lubri-
cation to the dust and shaft seals. Also lubricate all
part surfaces freely with clean hydraulic fluid.
Install a new input shaft bearing cup (1), and swash
plate bearings (2).
70-421-973 9
A.10.A / 90
11. Install input shaft into housing.
70-421-456 10
12. Install swash plate control spring (1) and swash plate
bearings (2).
70-421-462 11
13. Reassemble the swash plate (1), into the housing by

tilting the swash plate with the push rod socket up
slightly and installing.
NOTE: Caution must be used when installing the complete
swash plate so as not to dislodge the swash plate spring
or the saddle bearings.
70-421-461_460 12
14. Insert the push rod (1), through the stroke piston bore
and reengage the end of the tube into the swash
plate socket.
70-421-476 13
A.10.A / 91
15. Tilt the swash plate up and insert the push rod (1),
down and into the socket. Make sure the push rod is
engaged in the socket correctly.
1b0o2004061062 14
16. Install the stroke control piston (2), in the bore. Screw
the plug (1), back on.
70-421-473 15
Pumping Head and Piston Assembly

17. Install the guide pins (1), in the block splines.
70-421-972 16
A.10.A / 92
18. Lubricate and install the bearing (1), spider and pis-
ton assemblies (2), on the pivot and into the block
assembly.
70-421-468 17
19. Check bearing preload before installing the rotating

group. Install bearing (1), and spacer (2), on the
shaft.
70-421-492 18
Next operation:
Install the charge pump as described in Charge pump - Overhaul (A.10.A).
A.10.A / 93
Hydraulic pump Variable displacement pump - Replace (Input shaft

seal) [15216440]
Prior operation:
Hydraulic pump Variable displacement pump - Remove (A.10.A)
1. When replacing the input shaft seal, make sure the

pump housings mounting flange is clean. Use circlip
pliers to remove the input shaft seal retaining ring.
1b0o2004061061 1
2. With the retaining ring removed, use a punch or sim-

ilar tool, and carefully pierce the top of the lip seal.
Using the punch, pry the seal from its bore.
70-421-485 2
3. Protect the inner lip of the new shaft seal (1), lubri-
cate and install the seal over the input shaft (2), and
into the pump housing.
70-421-528 3
4. Tap the shaft seal into the pump housing until it is just
slightly below flush of the counterbore face.
NOTE: Do not seat the seal this time.
A.10.A / 94
5. Use a seal driver, (1), such as a 31.8 mm (1.25 in)

ID 38.1 mm (1.5 in) OD x 63.5 mm (2.5 in) long pipe
as shown here, to press both the retaining ring and
shaft seal into the pump housing.
NOTE: Press the retaining ring in just far enough that it
snaps into the retaining ring groove machined into the
pump housing.
70-421-482_456 4
Next operation:
Hydraulic pump Variable displacement pump - Install (A.10.A)
A.10.A / 95
Hydraulic pump Variable displacement pump - Install [15215155]

Prior operation:
Charge pump - Overhaul (A.10.A)
1. Install the pump and tighten the nuts.
BSD2052A 1
2. Install filter housing, related tubes and elbows includ-

ing the supplementary lube valve.
3. Ensure lubrication pipe banjo connector and brake
line retaining bracket are connected to the pump
body.
4. Connect all electrical and hydraulic connections to
pump.
5. Install the intake filter (3) by installing the retaining
bolts (2).
Install charge filter (1) by screwing clockwise.
BSE2755A_455 2
Install the filter housing and tighten the retaining bolts to 40

N·m (29.5 lb ft).
BAIL08CVT263AVA 3
A.10.A / 96
6. Connect all the relevant hoses and pipes. Ensure the

oil filter vent cap is tightened.
BAIS06CCM055AVB 4
Next operation:
Install the right hand rear wheel - see Rear wheel - Install (D.50.C).
Refill the driveline with the correct specification oil - see Consumables Lubrications and Coolants.
A.10.A / 97
Hydraulic pump Variable displacement pump - Pressure test

[17129424]
The following tests check operation of the hydraulic pump and associated high pressure circuits.
NOTICE: Before performing any pressure testing operate the tractor until the oil in the rear axle is at normal operating
temperature 75 °C (167 °F).
Standby Pressure
1. Remove the pressure compensating valve plug
and install the 90 ° quick release fitting adaptor
380001146 (1).
- Test port thread M8 x 1.0
BVE0153A 1
2. Attach a 0 - 40 bar (0 - 580 psi) pressure gauge

380000552, using the quick release coupler
380000543 (1) and the hose 380000545.
BVE0154A 2
3. Set the engine speed to 1500 rev/min to observe the

system operation pressure or 2200 rev/min for the
maximum system pressure.
The pressure reading should be 22 - 24 bar ( 319 -
348 lbf/in²) and is the `Standby Pressure`.
NOTICE: Do Not operate the tractor brakes or any remote control valve lever, otherwise the system pressure will
increase to maximum pressure of 205 - 215 bar (2973 - 3118 psi) this will result in damage to the pressure gauge.
A.10.A / 98
4. If the pressure reading is not to the specification, ad-

just the flow compensating valve (1).
If the pressure reading is high, examine the flow com-
pensating valve (1) spool for sticking.
BVE0154B 3
Maximum Pressure
5. Remove the pressure compensating valve plug
and install the 90 ° quick release fitting adaptor
380001146 (1).
BVE0153A 4
6. Attach a 0 - 250 bar (0 - 3625 psi) pressure

gauge 380000553, using the quick release coupler
380000543 (1) and the hose 380000545.
BVE0154A 5
A.10.A / 99
7. Set the remote control valve number 1 in the Èxtend'

position.
Set the engine speed to 1500 rev/min to observe the
The pressure reading should be 205 - 215 bar (2973
- 3118 psi) and is the `Maximum Pressure`.
BVE0159C 6
8. If the pressure reading is not to specification adjust

the pressure compensating valve (2).
BVE0154B 7
Charge Pressure
9. Remove the charge pressure switch and install the
adaptor 380000572 (1) and the quick release fitting
380000492 (2).
Attach a 0 - 10 bar (0 - 145 psi) pressure gauge
380000551, using the quick release coupler
380000543 and the hose 380000545.
BSE2607A 8
A.10.A / 100
10. Install a 180 l/min (47.55 US gpm) flow meter be-

tween the remote control valves number 1 and num-
ber 2. Ensure the inlet hose of the flow meter is in-
stalled into the extend port of valve number 1.
Fully open the load valve on the flow meter.
Set the hydraulic oil flow to maximum.
BVE0158A 9
11. Set the remote control valve number 2 in the `Float'

position.
Set the remote control valve number 1 in the Èxtend'
position.
Set the engine speed to 1500 rev/min to observe the
BVE0159A 10
12. Move the remote control valve lever for the remote
control valve number 1 between the extend and neu-
tral position.
13. The following pressures should be observed:
• 6 - 8 bar (87 - 116 psi) - Neutral
• 2 bar (29 psi) - Extend
If the pressure reading is below 1.6 bar (23.2 psi),
replace the hydraulic oil filters and re-test.
If after re-test the charge pressure is still below the
specification, check the supplementary lube valve,
examine both the charge pressure filter dump valve
and the charge pressure valve before disassembling
the hydraulic oil pump to inspect for wear.
A.10.A / 101
Thank you very much
for your reading.
Please Click Here
Then Get More
Information.

CASE IH MAXXUM 125 TRACTOR Service Repair Manual PDF

Uploaded by

Copyright:

Available Formats

CASE IH MAXXUM 125 TRACTOR Service Repair Manual PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CASE IH MAXXUM 125 TRACTOR Service Repair Manual PDF

Uploaded by

Copyright:

Available Formats

What systems are covered in the service manual?

What systems are covered in the service manual?

What are the main components of the primary hydraulic power system?

What are the main components of the primary hydraulic power system?

SERVICE MANUAL

MAXXUM 100 , MAXXUM 110 Multicontroller , MAXXUM 110 , MAXXUM 115

SECONDARY HYDRAULIC POWER SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.12.A

ENGINE AND PTO IN ................................................................... B

TRANSMISSION, DRIVE AND PTO OUT ........................................ C

ADDITIONAL REDUCERS Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.30.D

FRONT PTO Hydraulic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.42.C

STEERING Hydraulic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.20.C

SERVICE BRAKE Hydraulic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.30.C

PARKING BRAKE Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.32.B

SUSPENSION Hydraulic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.40.C

WHEELS AND TRACKS Wheels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.50.C

FRAME AND CAB ........................................................................ E

HITCH AND WORKING TOOL ....................................................... H

That information could be:

How to Use this Manual

Each Chapter is divided into four Information types:

SECTION B, POWER PRODUCTION

SECTION C, POWER TRAIN

SECTION E, BODY AND STRUCTURE

SECTION G, TOOL POSITIONING

SECTION K, CROP PROCESSING

ENGINE - Dynamic description (B.10.A - C.30.A.10)

Information Units and Information Search

example information unit Stack valve - Sectional View (A.10.A.18 - C.10.A.30)

Page Header and Footer

The page footer will contain the following references:

Safety rules [3964943]

NOTES FOR EQUIPMENT

PAY ATTENTION TO THIS SYMBOL

WHEELS AND TYRES

REMOVAL AND INSTALLATION

HEALTH AND SAFETY

FUELS - see Fire, Legal Aspects, Chemicals - General, Solvents.. . . . . . . . . . . . . . . . 8

HEALTH AND SAFETY PRECAUTIONS

ACIDS AND ALKALIS

ADHESIVES AND SEALERS

Solvent based Adhesives/Sealers

Water based Adhesives/Sealers

Resin based Adhesives/Sealers

Anaerobic, Cyanoacrylate and other Acrylic Adhesives

Isocyanate (Polyurethane) Adhesives/ Sealers

BRAKE AND CLUTCH FLUIDS (Polyalkylene Glycols)

CHEMICAL MATERIALS - GENERAL

Clutch Linings and Pads

CORROSION PROTECTION MATERIALS

Gasolene (Petrol) Engine

Gas-Oil (Diesel Fuel)

Gas Shielded Welding

GENERAL WORKSHOP TOOLS AND EQUIPMENT

LUBRICANTS AND GREASES

Noise Insulation Materials

ECOLOGY AND THE ENVIRONMENT

The following are recommendations which may be of assistance:

Identification - Hexagonal nuts and locknuts classes 05 onwards