Scribd
Upload
186 views3 pages

Practical 24 PDF

This document describes experiments to measure the transpiration rate of plants using a potometer and to estimate the stomatal density of leaves. The procedure involves setting up a potometer with a leafy shoot, measuring the distance moved by an air bubble over time to determine transpiration rate, and peeling off leaf epidermis to count stomata under a microscope in order to calculate stomatal density. Factors such as light levels and air movement can influence transpiration rate measurements.

Uploaded by

Leo Tsoi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
186 views3 pages

Practical 24 PDF

This document describes experiments to measure the transpiration rate of plants using a potometer and to estimate the stomatal density of leaves. The procedure involves setting up a potometer with a leafy shoot, measuring the distance moved by an air bubble over time to determine transpiration rate, and peeling off leaf epidermis to count stomata under a microscope in order to calculate stomatal density. Factors such as light levels and air movement can influence transpiration rate measurements.

Uploaded by

Leo Tsoi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

62.........

Practical work

24. Measurement of the rate of transpiration using potometer

A simple experiment is described below to demonstrate


how the rate of transpiration of common plants found in
Hong Kong can be determined with the use of potometer.
Moreover, students can also be given the opportunity to
estimate the stomatal density of leaves from different
plants to evaluate the relationship between different
transpiration rates and this morphological feature.

A. Estimation of transpiration rate using a potometer

Fig. 1 Experimental set up

Procedure
1. Use a sharp razor blade to cut a leafy shoot under water.
2. Insert the leafy shoot through the hole of the stopper
provided with the potometer.
3. Fill the potometer with water and fit the stopper holding
the leafy shoot to the apparatus.
4. Use vaseline to seal all the connections of the apparatus.
Practical work.........63

5. Trap an air bubble in the capillary tube by the following


procedures:
• dip the end of the capillary tube into a beaker of
water,
• close the tap of the reservoir,
• take away the beaker of water and allow the plant
to transpire for a while, and
• re-immerse the capillary tube into the beaker of
water again.
6. Wait for about 5 minutes for the plant to equilibrate.
7. Estimate the rate of transpiration by measuring the
distance moved by the air bubble per unit time. Take
another measurement, and average the two readings.
8. Find out the total leaf surface area of the experimental
plant using a graph paper.
9. Transpiration rate can be expressed in terms of water
transpired per unit time per unit area of leaf surface.
10. If time permits, estimate the rate under different
environmental conditions, e.g. under direct incandescent
light illumination, under low light condition, in rapid air
movement (provided by a fan) or in still air.

Note
1. The total surface area of leaf should include the areas of
both upper and lower surfaces.
2. This potometer only measures the rate of water uptake,
it cannot find out the actual transpiration rate.
3. The volume of water transpired can be estimated using
the formula below:

Distance moved by air bubble = d cm


Cross-sectional area of capillary tube = a cm2
Volume of water transpired (V) = d x a cm3
64.........Practical work

B. Estimation of stomatal density on leaf surface

Procedure
1. Use a needle or a pair of fine forceps to make a
shallow cut on the lower surface of the leaf.
2. Use a pair of fine forceps to peel off the lower
epidermis.
3. Mount the epidermis in a drop of water on a
slide.
4. Using 100x magnification, move the slide to find
a portion which occupies the entire field of view,
count the number of stomata within the area
occupied.
5. Repeat step (4) 3-5 times to obtain a good
average value.
6. Repeat steps (1) to (5) for the upper epidermis of
the same leaf.
7. Given a copper wire of known diameter,
estimate the area covered by the microscope
field of view at 100x magnification.
8. Calculate the stomatal density of the upper and
lower epidermis of the plant.

Note
1. Plant materials suitable for this experiment are:
Hibiscus rosa-sinensis, Ligustrum sinense,
Bauhinia blakeana and Ficus microcarpa.
2. If it is difficult to obtain the epidermis by the
method described above, then try the nail
varnish method as mentioned in Practical work
6 of this Resource Kit.
3. Alternative method for estimating the diameter
is given in Practical work 5 of this Resource Kit.

You might also like