Scribd
Upload
95 views2 pages

Feedback in Amplifiers

The characteristics of an amplifier depend on transistor parameters like gain and impedances, which can vary. Feedback is used to overcome variations - it involves returning a fraction of the output signal to the input. Negative feedback reduces the input signal magnitude, while positive feedback increases it. For negative feedback, the amplifier gain is reduced to A/(1+Aβ), where β is the feedback ratio and Aβ is the loop gain. Positive feedback increases the gain to A/(1-βA).

Uploaded by

Dinesh Vel
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
95 views2 pages

Feedback in Amplifiers

The characteristics of an amplifier depend on transistor parameters like gain and impedances, which can vary. Feedback is used to overcome variations - it involves returning a fraction of the output signal to the input. Negative feedback reduces the input signal magnitude, while positive feedback increases it. For negative feedback, the amplifier gain is reduced to A/(1+Aβ), where β is the feedback ratio and Aβ is the loop gain. Positive feedback increases the gain to A/(1-βA).

Uploaded by

Dinesh Vel
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

FEEDBACK IN AMPLIFIERS

FEEDBACK IN AMPLIFIERS

The characteristics of an amplifier are highly dependent on transistor parameters like


current gain, input impedance and output impedance etc. The transistor parameters exhibit
variations due to ageing of transistors. Manufacturing processes cause variations in
parameters of transistors of the same type. To overcome any adverse effect on the overall
performance of an amplifier, feedback is used. Feedback is said to exist in an amplifier
circuit, when a fraction of the output signal is returned or fed back to the input and
combined with the input signal. If the magnitude of the input signal is reduced by the feed
back, the feed back is called negative or degenerative. If the magnitude of the input signal is
increased by the feed back, such feed back is called positive or regenerative.

Principle of feedback amplifier

For an ordinary amplifier i.e. without feedback, let V0 and Vi be the output voltage and
input voltage respectively. If A be the voltage gain of the amplifier, then

A =VO/Vi

The gain A is often called as open–loop gain. The general theory of feedback can be
explained with the help of block diagram shown in Fig 9.39. The feedback amplifier has two
parts (i.e) amplifier and feedback circuit. The feedback circuit usually consists of passive
components (resistor, capacitor, inductor). A fraction (say β) of the output voltage is fed
back to the input through the feedback circuit. Let V′ ο be the output voltge with feedback.

Feedback amplifier

Page 1
FEEDBACK IN AMPLIFIERS

Therefore, after feedback the input voltage V′ i becomes,

V′ i = Vi + βV′ ο ... (1)

For positive feedback, β is taken as positive. For negative feedback, β is taken as negative.

For positive feedback, the input voltage will be Vi + βV′ ο. When this is amplified A times by
the amplifier, the output voltage after feedback (V′ ο) will be A(Vi + βV′ ο)

∴ V′ ο = A (Vi + βV′ ο ) ... (2)

V′ ο (1– βA) = AVi ... (3)

Then the voltage gain of the amplifier with feedback is

Af = V′ο/Vι =A/1- βA

Since |1−βA| < 1, Af >A. The positive feedback increases the amplifier gain.

For negative feedback, the feedback fraction is – β

∴ Af = A/1− (−Aβ )= A/1 + Aβ

Since |1+βA| > 1, Af <A. Therefore negative feedback reduces the amplifier gain. The term
Aβ is called loop gain and β is called feedback ratio.

Page 2

You might also like