Single BQ

Summary
Description Page No Amount
Summary
WORK BELOW LOWEST FLOOR FINISH BQ/1/4 230,694.60
FRAME BQ/2/8 441,488.20
UPPER FLOOR BQ/3/2 507,277.98
ROOF BQ/4/8 202,915.35
STAIRS, RAMPS AND STAIRCASE FINISHES BQ/5/5 57,645.04
EXTERNAL WALLS BQ/6/2 123,085.62
INTERNAL WALLS AND PARTITIONS BQ/7/2 256,776.68
WINDOWS BQ/8/4 235,736.02
DOORS BQ/9/4 236,913.35
INTERNAL WALL FINISHES BQ/10/2 433,244.60
INTERNAL FLOOR FINISHES BQ/11/2 149,793.40
INTERNAL CEILING FINISHES BQ/12/2 134,183.45
EXTERNAL FINISHES BQ/13/2 89,657.30
PLUMBING SERVICES &SANITARY FITTINGS BQ/14/4 68,448.00
MECHANICAL & ELECTRICAL INSTALLATION BQ/15/2 33,000.00
BUILDER'S WORK BQ/16/2 31,241.04
LETTER BOXES AND SIGNS BQ/17/2 3,215.50
Total Per Unit (MYR) 3,235,316.13

Total Unit(s) X 5
Total Amount To Form Of Tender (MYR) 16,176,580.65
Summary Page I
WORK BELOW LOWEST FLOOR FINISH
Item Description Unit Qty Rate Amount
ELEMENT NO. 2 - WORK BELOW LOWEST FLOOR

FINISH
Excavate, get out, part return, fill in and

ram and deposit in making up levels where
directed within the site and remainder load
and cart away
A Oversite to reduce level m3 824 11.00 9,064.00
B Pile cap not exceeding 1.50m deep including

working around pile heads m3 141 9.00 1,269.00
C Ground beam not exceeding 1.50m deep m3 71 9.00 639.00
D Trench not exceeding 1.50m deep m3 24 9.00 216.00
E Prepare and apply 'Simechem' or other equal

and approved anti-termite chemical
treatment to building lot. The Tenderer
shall also allow for a warranty period of
10 years including annual inspection m2 2,288 2.90 6,635.20
F 100mm Bed of hardcore as described spread,

levelled, well rammed and consolidated,
watered and blinded with fine sand, well
rolled and finished to receive concrete bed
(measured separately) m2 2,288 4.80 10,982.40
50mm Concrete Grade 10 as described

blinding screed, spread and levelled under
G Pile cap including working around pile head m2 175 7.40 1,295.00
H Ground beam m2 272 7.40 2,012.80
J 150mm Base m2 20 7.40 148.00
K 100mm Bed m2 2,288 7.40 16,931.20
Reinforced concrete Grade 25 as described

in
L Ground beam m3 125 159.00 19,875.00
M 150mm Base m2 20 23.85 477.00
N 150mm Wall m2 44 23.85 1,049.40
P 100mm Bed m2 2,288 15.90 36,379.20
To Collection (MYR) 106,973.20
BQ/1/1
WORK BELOW LOWEST FLOOR FINISH (CONT'd)

FINISH (CONT'd)

in (CONT'd)
A Extra over for thicknessing to an

average width of 250mm and to a total depth
of 200mm including all additional
excavation, formwork, hardcore and
handpacking hardcore to one side m 30 12.00 360.00
B Ditto to an average width of 650mm and to a

total depth of 200mm ditto m 16 31.00 496.00
C Reinforced concrete Grade 30 as described

in pile cap m3 132 167.00 22,044.00
Mild steel bar reinforcement as described

in
D 10mm Diameter as column starter bar links kg 1,308 1.66 2,171.28
E 10mm Diameter as stirrups in ground beam kg 129 1.66 214.14
F 8mm Ditto kg 3,165 1.66 5,253.90
High yield steel bar reinforcement as

described in
Pile cap
G 20mm Diameter kg 2,901 1.55 4,496.55
H 16mm Ditto kg 8,905 1.55 13,802.75
J 12mm Ditto kg 5,052 1.64 8,285.28
K 10mm Ditto kg 125 1.64 205.00
Column Starter Bar
L 20mm Diameter kg 4,049 1.55 6,275.95
M 16mm Ditto kg 3,429 1.55 5,314.95
Ground beam
N 16mm Diameter kg 454 1.55 703.70
P 12mm Ditto kg 4,679 1.64 7,673.56
Q 10mm Ditto kg 1,631 1.64 2,674.84
BQ/1/2
WORK BELOW LOWEST FLOOR FINISH (CONT'd)

FINISH (CONT'd)

described in (CONT'd)
Ground beam (CONT'd)
A 10mm Diameter in base kg 260 1.64 426.40
B 10mm Diameter in wall kg 555 1.64 910.20
Sawn formwork as described to
C Sides of pile cap m2 279 20.00 5,580.00
D Sides of ground beam m2 1,573 20.00 31,460.00
E Sides of wall m2 93 20.00 1,860.00
F Edge of concrete not exceeding 100mm high m 31 2.30 71.30
G 75mm x 75mm Triangular fillet planted on

formwork to form rebate m 43 2.20 94.60
H Forming 100mm x 100mm deep scupper drain on

concrete slab including trowelling smooth
and all additional formwork m 31 7.60 235.60
J 75mm x 75mm x 6mm Thick mild steel as

described angle framing with and including
12mm diameter mild steel anchor bar 100mm
long welded to angle frame at 300mm centres
with fishtailed and cast into concrete
including painting exposed surfaces with
one coat metallic primer and two coats
bituminous paint m 43 43.00 1,849.00
K 75mm Precast concrete Grade 20 as described

cover slab size 300mm x 425mm long
reinforced with and including 3 Nos. 10mm
diameter mild steel bars horizontally and
10mm diameter mild steel bars vertically at
200mm centres with 2 Nos. lifting notches
at ends and placing in position no. 6 10.00 60.00
L 75mm Ditto size 300mm x 725mm long ditto no. 43 16.80 722.40
M 75mm Ditto size 300mm x 1025mm long ditto no. 20 24.00 480.00
BQ/1/3
Description Amount
Collection
Page No. BQ/1/1 106,973.20
Page No. BQ/1/2 79,971.90
Page No. BQ/1/3 43,749.50
Carried To Summary (MYR) 230,694.60
BQ/1/4
FRAME
FRAME
ELEMENT 2 - FRAME
VIBRATED REINFORCED CONCRETE GRADE 25 AS

DESCRIBED IN
A Column m3 102 175.00 17,850.00
B Projected coping m3 4 175.00 700.00
C Column on beam m3 1 175.00 175.00
D Circular column m3 38 175.00 6,650.00
E Stiffener (Provisional) m3 25 175.00 4,375.00
F Suspended ground beam m3 91 175.00 15,925.00
G Ditto; circular on plan of 1875mm radius m3 2 175.00 350.00
H Suspended curved ground beam m3 1 175.00 175.00
J Suspended floor beam m3 55 175.00 9,625.00
K Arch beam; to a varies radius m3 17 175.00 2,975.00
L Sloping roof beam m3 6 175.00 1,050.00
M Lower roof beam m3 48 175.00 8,400.00
N Upstand lower roof beam m3 9 175.00 1,575.00
P Upper roof beam m3 19 175.00 3,325.00
Q Lower ring beam m3 9 175.00 1,575.00
R Upper ring beam m3 6 175.00 1,050.00
S Plinth m3 5 175.00 875.00
T 200mm Thick wall m2 26 35.00 910.00
MILD STEEL BAR REINFORCEMENT TO CONCRETE AS

DESCRIBED IN
Column
U 6mm Diameter bar as links kg 511 1.90 970.90
V 8mm Diameter ditto kg 268 1.90 509.20
W 10mm Diameter ditto kg 269 1.90 511.10
BQ/2/1
FRAME
FRAME (CONT'd)
ELEMENT 2 - FRAME (CONT'd)

DESCRIBED IN (CONT'd)
Projected coping
A 6mm Diameter bar as links kg 18 1.90 34.20
Column on beam
B 6mm Diameter bar as links kg 2 1.90 3.80
Circular column
C 6mm Diameter bar as links kg 44 1.90 83.60
D 8mm Diameter ditto kg 327 1.90 621.30
Stiffener (Provisional)
E 6mm Diameter bar as links kg 138 1.90 262.20
Suspended ground beam
F 6mm Diameter bar as stirrups kg 68 1.90 129.20
G 8mm Diameter ditto kg 79 1.90 150.10
H 10mm Diameter ditto kg 1,399 1.90 2,658.10
Suspended ground beam, circular on plan of

1875mm radius
J 10mm Diameter bar as stirrups kg 111 1.90 210.90
Suspended curved ground beam
K 10mm Diameter bar as stirrups kg 21 1.90 39.90
Suspended floor beam
L 6mm Diameter bar as stirrups kg 118 1.90 224.20
M 8mm Diameter ditto kg 33 1.90 62.70
N 10mm Diameter ditto kg 3,192 1.90 6,064.80
Arch beam; to a varies radius
P 6mm Diameter bar as stirrups kg 36 1.90 68.40
Q 10mm Diameter ditto kg 144 1.90 273.60
BQ/2/2
FRAME
FRAME (CONT'd)

Sloping roof beam
A 10mm Diameter bar as stirrups kg 175 1.90 332.50
Lower roof beam
B 6mm Diameter bar as stirrups kg 37 1.90 70.30
C 10mm Diameter ditto kg 1,872 1.90 3,556.80
Upstand lower roof beam
D 8mm Diameter bar as stirrups kg 6 1.90 11.40
E 10mm Diameter ditto kg 240 1.90 456.00
Upper roof beam
F 8mm Diameter bar as stirrups kg 99 1.90 188.10
Lower ring beam
H 10mm Diameter bar as stirrups kg 314 1.90 596.60
Upper ring beam
J 10mm Diameter bar as stirrups kg 120 1.90 228.00
Plinth
K 10mm Diameter bar as stirrups kg 153 1.90 290.70
HIGH TENSILE BAR REINFORCEMENT TO CONCRETE

AS DESCRIBED IN
Column
L 16mm Diameter bar kg 13,049 1.90 24,793.10
M 20mm Diameter ditto kg 14,392 1.90 27,344.80
Projected coping
N 10mm Diameter bar kg 6 1.90 11.40
P 12mm Diameter ditto kg 85 1.90 161.50
BQ/2/3
FRAME
FRAME (CONT'd)

Column on beam
A 16mm Diameter bar kg 47 1.90 89.30
Circular column
B 16mm Diameter bar kg 1,436 1.90 2,728.40
C 20mm Diameter ditto kg 8,764 1.90 16,651.60
Stiffener (Provisional)
D 12mm Diameter bar kg 1,336 1.90 2,538.40
Suspended ground beam
E 12mm Diameter bar kg 45 1.90 85.50
F 16mm Diameter ditto kg 1,146 1.90 2,177.40
G 20mm Diameter ditto kg 6,570 1.90 12,483.00
H 25mm Diameter ditto kg 9,728 1.90 18,483.20
Suspended ground beam, circular on plan of

1875mm radius
J 20mm Diameter bar kg 650 1.90 1,235.00
Suspended curved ground beam
K 25mm Diameter bar kg 428 1.90 813.20
Suspended floor beam
L 12mm Diameter bar kg 24 1.90 45.60
M 16mm Diameter ditto kg 2,008 1.90 3,815.20
P 25mm Diameter ditto kg 15,334 1.90 29,134.60
Arch beam; to a varies radius
Q 12mm Diameter bar kg 297 1.90 564.30
R 16mm Diameter ditto kg 1,422 1.90 2,701.80
BQ/2/4
FRAME
FRAME (CONT'd)

Arch beam; to a varies radius (CONT'd)
A 20mm Diameter ditto kg 134 1.90 254.60
Sloping roof beam
B 16mm Diameter bar as starter bar kg 1,197 1.90 2,274.30
Lower roof beam
C 16mm Diameter bar kg 3,283 1.90 6,237.70
D 20mm Diameter ditto kg 5,004 1.90 9,507.60
E 25mm Diameter ditto kg 6,784 1.90 12,889.60
Upstand lower roof beam
F 12mm Diameter bar kg 127 1.90 241.30
H 20mm Diameter ditto kg 73 1.90 138.70
J 25mm Diameter ditto kg 3,173 1.90 6,028.70
Upper roof beam
K 16mm Diameter bar kg 1,521 1.90 2,889.90
L 20mm Diameter ditto kg 2,523 1.90 4,793.70
Lower ring beam
M 16mm Diameter bar kg 42 1.90 79.80
Upper ring beam
P 20mm Diameter bar kg 1,395 1.90 2,650.50
Plinth
Q 16mm Diameter bar kg 551 1.90 1,046.90
R 20mm Diameter ditto kg 483 1.90 917.70
BQ/2/5
FRAME
FRAME (CONT'd)

BRC FABRIC REINFORCEMENT WITH 150mm SIDE

AND END LAPS (MEASURED NETT - NO ALLOWANCE
MADE FOR LAPS)
A Two layers of BRC A8 in wall m2 26 24.00 624.00
SAWN FORMWORK AS DESCRIBED
B To sides of column m2 1,498 24.00 35,952.00
C Ditto column on beam m2 5 24.00 120.00
D Ditto circular column, 300mm radius m2 431 24.00 10,344.00
E Ditto stiffener (Provisional) m2 355 24.00 8,520.00
F Ditto wall m2 51 24.00 1,224.00
G To sides and soffit of suspended ground

beam m2 1,147 24.00 27,528.00
H Ditto; circular on plan of 1875mm radius m2 20 24.00 480.00
J Ditto suspended curved ground beam to a

radius of 3600mm m2 5 24.00 120.00
K Ditto suspended floor beam m2 726 24.00 17,424.00
L Ditto arch beam; to a varies radius m2 162 24.00 3,888.00
M Ditto lower roof beam m2 624 24.00 14,976.00
N Ditto upstand lower roof beam m2 75 24.00 1,800.00
P Ditto upper roof beam m2 209 24.00 5,016.00
Q Ditto lower ring beam m2 104 24.00 2,496.00
R Ditto upper ring beam m2 57 24.00 1,368.00
S Ditto plinth m2 56 24.00 1,344.00
T Ditto projected coping to follow designed

profile m2 37 24.00 888.00
U Ditto sides and soffit of sloping roof

beam; exceeding 15 degrees from horizontal m2 29 24.00 696.00
BQ/2/6
FRAME
FRAME (CONT'd)

SAWN FORMWORK AS DESCRIBED (CONT'd)
A Ditto sloping top ditto m2 12 24.00 288.00
To Collection (MYR) 288.00
BQ/2/7
FRAME
Description Amount
FRAME
Collection
Page No. BQ/2/1 79,551.20
Page No. BQ/2/2 10,887.00
Page No. BQ/2/3 58,673.90
Page No. BQ/2/4 103,470.20
Page No. BQ/2/5 53,809.90
Page No. BQ/2/6 134,808.00
Page No. BQ/2/7 288.00
BQ/2/8
UPPER FLOOR
UPPER FLOOR
ELEMENT NO. 4 - UPPER FLOOR
A 110mm Reinforced concrete Grade 25 as

described in suspended slab m2 11,045 17.50 193,287.50
B 10mm Diameter high yield steel bar

reinforcement as described in suspended
slab kg 8,552 1.64 14,025.28
C Layer of steel fabric reinforcement to B.S.

4483 (BRC. Ref. No. A6 - weighing not less
than 2.22 kg/m2) as described well lapped
at joints and embedded in suspended slab
(measured nett - no allowance made for
laps) m2 19,155 6.70 128,338.50
D Soffit of suspended slab m2 9,807 17.00 166,719.00
E Forming 100mm x 25mm deep scupper drain on

and all additional formwork m 861 5.70 4,907.70
BQ/3/1
UPPER FLOOR
Description Amount
UPPER FLOOR
Collection
Page No. BQ/3/1 507,277.98
BQ/3/2
ROOF
ROOF
ELEMENT NO. 5 - ROOF

in
A 110mm Suspended roof slab m2 56 17.30 968.80
B 185mm Ditto m2 60 29.00 1,740.00
C 10mm Diameter mild steel bar reinforcement

as described in suspended roof slab kg 63 1.66 104.58
D 10mm Diameter high yield steel bar

reinforcement ditto kg 223 1.64 365.72
E 10mm Diameter as dowel bar 300mm long,

twice bent with one end cast into
reinforced concrete beam and other end
morticed through and fixed to timber wall
plate with fixing nails (measured
separately) no. 800 1.00 800.00
F Layer of steel fabric reinforcement to B.S.

4483 as described (BRC Ref. No. A6 -
weighing not less than 2.22 kg. per m2)
well lapped at joints and embedded in
suspended roof slab (measured nett - no
allowance made for laps) m2 170 6.70 1,139.00
G Sawn formwork as described to soffit of

roof slab m2 103 17.00 1,751.00
H Forming 200mm x 75mm deep scupper drain on

and all additional formwork m 60 9.00 540.00
J 13mm Cement and sand (1:3) as described

protective screed to top of waterproofing
membrane (measure separately) to sides and
top of roof slab m2 121 5.75 695.75
K Supply and lay 1.3mm thick 'FOSROC'

Nitoproof 600 elastometric membrane as
described or other equal and approved
waterproofing system sandwiched between
concrete structure and cement and sand
protective screed (both measured
separately) with and including forming 12mm
wide contraction/expansion joints at 600mm
centres all as per manufacturer's
instruction to sides and top of roof slab m2 121 24.80 3,000.80
BQ/4/1
ROOF
ROOF (CONT'd)
ELEMENT NO. 5 - ROOF (CONT'd)

in (CONT'd)
A Extra over for working around 200mm x

75mm high scupper drain m 60 8.70 522.00
B 4.5mm Thick corrugated asbestos free cement

roofing sheet as 'Ardex Plus' or other
equal and approved fixed to timber purlins
all in accordance with manufacturer's
instruction (measured nett - no allowance
made for laps) m2 3,162 15.00 47,430.00
C Extra over for ridge capping as 'UAC -

Ardex Plus' or other equal and approved
bedded in cement and sand (1:3) mortar
including all necessary fixing accessories
and clips (ditto) m 345 12.00 4,140.00
The following in 136 Nos. timber roof

trusses each overall span 5.10m x 1.16m
rise all in sawn pressure treated Group 'B'
timber all fixed together with approved
'Pryda' or other equal and approved system
including hoisting and fixing at a height
of 13.60m above ground level (Type T1 )
D 40mm x 70mm Diagonal strut m 490 4.00 1,960.00
E 40mm x 70mm Bottom chord m 538 4.00 2,152.00
F 40mm x 95mm Rafter m 803 5.50 4,416.50
G 40mm x 95mm Waling plate m 157 5.50 863.50
H 'Pryda' or other equal and approved

'Multigrip' system no. 884 3.90 3,447.60
(End of 136 Nos. timber roof trusses type

'T1')

of 13.60m above ground level (Type T1A )
J 40mm x 70mm Diagonal strut m 87 4.00 348.00
BQ/4/2
ROOF
ROOF (CONT'd)

of 13.60m above ground level (Type T1A )
(CONT'd)
A 40mm x 70mm Bottom chord m 95 4.00 380.00
B 40mm x 95mm Rafter m 137 5.50 753.50
C 40mm x 95mm Waling plate m 28 5.50 154.00
D 'Pryda' or other equal and approved

'Multigrip' system no. 156 3.90 608.40

'T1A')

E 40mm x 70mm Diagonal strut m 1,952 4.00 7,808.00
F 40mm x 70mm Bottom chord m 480 4.00 1,920.00
G 40mm x 95mm Rafter m 944 5.50 5,192.00
H 40mm x 95mm Waling plate m 184 5.50 1,012.00
J 'Pryda' or other equal and approved

'Multigrip' system no. 1,040 3.90 4,056.00

'T2')
BQ/4/3
ROOF
ROOF (CONT'd)

A 40mm x 70mm Bottom chord m 60 4.00 240.00
B 40mm x 95mm Rafter m 68 5.50 374.00
C 'Pryda' or other equal and approved


'T3')

D 40mm x 70mm Bottom chord m 85 4.00 340.00
E 40mm x 95mm Rafter m 105 5.50 577.50
F 'Pryda' or other equal and approved


'T4')
G 230mm x 19mm Wrot pressure treated Grade

'B' as described fascia board m 448
Sawn pressure treated Group 'B' timber as

described
H 70mmx 40mm Purlins (Provisional) m 3,756 4.00 15,024.00
J 70mm x 40mm Diagonal web bracing m 469 4.00 1,876.00
K 95mm x 40mm Wall plate m 1,171 5.50 6,440.50
BQ/4/4
ROOF
ROOF (CONT'd)
The following in 2 Nos. of covered walkway

each overall size 42.00m length x 1.90m
wide x 2.70m high and fixing at a height
approximately 13.60m above ground floor
level
Mild steel as described
A 50mm x 100mm x 5mm Thick rectangukar hollow

section as tie beam kg 2,263 4.20 9,504.60
B 65mm x 150mm (extreme) x 6mm Thick

triangular stiffener plate welded to post
and base plate (both post and plate
measured separately) no. 128 2.00 256.00
C 70mm x 120mm x 6mm Thick connection plate

welded to beam (measured separately) no. 112 3.00 336.00
D 70mm x 120mm x 6mm Thick welded to plate

(ditto) no. 24 3.00 72.00
E 100mm x 100mm x 8mm Thick connection plate

welded to post (measured separately) no. 176 3.00 528.00
F 100mm x 100mm x 8mm Thick ditto welded to

beam (ditto) no. 88 3.00 264.00
G 100mm x 100mm (extreme) x 8mm Thick

connection plate welded to beam and bolted
to timber rafter (both beam and rafter
measured separately) no. 176 3.00 528.00
H 100mm x 140mm (extreme) x 8mm Thick ditto

(measured separately) no. 64 4.00 256.00
J 114.30mm Diameter x 6.3mm thick circular

hollow section as post kg 2,904 4.20 12,196.80
K 125mm x 125mm x 6mm Thick top plate no. 64 7.00 448.00
L 150mm x 250mm x 10mm Thick base plate no. 88 12.50 1,100.00
M 150mm x 500mm girth x 6mm Thick plate as

strap anchor welded to base plate and
embeded into concrete (measured separately) no. 64 12.50 800.00
N 16mm Diameter high tensile bolts 100mm

long, with head, nut and washer including
drilling through 16mm mild steel plate
(ditto) no. 448 1.80 806.40
BQ/4/5
ROOF
ROOF (CONT'd)
Mild steel as described (CONT'd)
A 16mm Diameter high tensile bolts 140mm

long, with head, nut and washer embedded
into concrete (ditto) no. 48 2.00 96.00
B 20mm Diameter high tensile bolts 100mm

long, with head, nut and washer including
drilling through 40mm thick timber trusses
(ditto) no. 148 2.50 370.00
C Prepared and apply two coats of primer and

two coats of micaceous iron oxide paint to
general surfaces of stuctural steelwork tonne 5.9 600.00 3,540.00
(End of 2 No. covered walkway)
D 30mm x 0.8mm Thick galvanised mild steel

flat strap as 'Pydra Strap Brace' m 634 4.00 2,536.00
No. 22 Gauge galvanised iron sheet

(measured nett - no allowance made for
laps)
E Flashing twice bent 300mm girth with one

edge dressed over concrete or brickwork and
other edge dressed over roofing sheet m 806 11.50 9,269.00
F Flashing once bent 500mm girth with one end

fixed to gutter and other edge dressed in
timber batten m 448 15.30 6,854.40
G Flashing three bent 500mm girth with one

edge dressed over concrete or brickwork and
other edge dressed over roofing sheet m 8 15.30 122.40
H 600mm x 600mm Vent pipe flashing with all

edges tucked into roofing sheet and
including forming perforation for 75mm
diameter pipe and all necessary painting
and sealing materials no. 40 21.00 840.00
No. 20 Gauge galvanised iron rainwater

downpipes (measured nett - no allowance
made for laps)
J Gutter 440mm girth, four times bent fixed

to timber trusses with approved brackets m 448 23.00 10,304.00
K Extra over for stop end no. 24 5.00 120.00
BQ/4/6
ROOF
ROOF (CONT'd)
No. 20 Gauge galvanised iron rainwater

downpipes (measured nett - no allowance
made for laps) (CONT'd)
A Ditto for opening to 100mm x 100mm rain

water downpipe outlet (measured separately) no. 36 9.50 342.00
B 100m x 100mm Pipe fixed to concrete or

brick wall with approved holderbats m 490 23.00 11,270.00
C Extra over for bend no. 36 7.70 277.20
D Ditto for swan neck no. 36 7.70 277.20
E Approved galvanised iron domed grating set

in on top of 100mm x 100mm rainwater
downpipe including filling joints with
mastic no. 36 21.00 756.00
F 75mm Diameter x 100mm long UPVC spout pipe

cast into concrete or brickwork no. 4 8.00 32.00
G 150mm x 150mm white uPVC floor trap cover

set into concrete roof slab and jointing to
uPVC pipe including cement and sand (1:3)
mortar no. 16 10.00 160.00
Prepare and apply one coat mordant solution

and three coats alkyd resin based paint on
the surfaces of galvanised iron surfaces
H Gutter m2 198 4.80 950.40
J Flashing m2 470 4.80 2,256.00
K Downpipes m2 196 4.80 940.80
L Knot with gold size, stop, prime with dull

aluminium wood primer and apply one
undercoat and two coats alkyd resin based
paint on surfaces of fascia board m2 104 4.80 499.20
BQ/4/7
ROOF
Description Amount
ROOF
Collection
Page No. BQ/4/1 11,105.65
Page No. BQ/4/2 65,279.60
Page No. BQ/4/3 21,883.90
Page No. BQ/4/4 25,737.80
Page No. BQ/4/5 27,095.80
Page No. BQ/4/6 34,051.80
Page No. BQ/4/7 17,760.80
BQ/4/8
STAIRS, RAMPS AND STAIRCASE FINISHES
ELEMENT NO. 6 - STAIRS, RAMPS AND STAIRCASE

FINISHES

in
A Staircase m3 19 159.00 3,021.00
B Landing beam m3 3 159.00 477.00
C 125mm Suspended landing slab m2 59 20.00 1,180.00
D 150mm Thick ramp slab including forming

groove line 12mm x 12mm at 100mm centres
(Provisional) m2 2 26.00 52.00
E 8mm Diameter mild steel bar reinforcement

as described stirrups in landing beam kg 102 1.66 169.32

described
Staircase
F 12mm Diameter kg 523 1.64 857.72
G 10mm Ditto kg 503 1.64 824.92
Landing beam
H 12mm Diameter kg 55 1.64 90.20
J 10mm Ditto kg 38 1.64 62.32
Suspended landing slab
K 12mm Diameter kg 917 1.64 1,503.88
L 10mm Ditto kg 497 1.64 815.08
Ramp slab
M 12mm Diameter (Provisional) kg 192 1.64 314.88
N 10mm Ditto (Provisional) kg 128 1.64 209.92
P Sloping soffit of staircase m2 96 17.00 1,632.00
Q Sides and soffit of landing beam m2 41 17.00 697.00
R Soffit of suspended landing slab m2 53 17.00 901.00
BQ/5/1

(CONT'd)

FINISHES (CONT'd)
Sawn formwork as described to (CONT'd)
A Undercut riser 168.75mm high m 308 4.00 1,232.00
B String of staircase 300mm (extreme) wide

including cutting to profile of tread and
riser m 160 7.50 1,200.00
C Edge of concrete exceeding 100mm and not

exceeding 200mm high m 4 4.60 18.40
Cement and sand (1:3) as described
D 28mm Paving trowelled smooth to landing m2 59 77.00 4,543.00
E 28mm Ditto to undercut riser 167mm high m 308 4.10 1,262.80
F 28mm Ditto to tread 255mm wide m 269 4.80 1,291.20
G Extra over for forming 2 rows of

grooveline each of 6mm wide to edge of
treads and landing m 308 3.00 924.00
Staircase Railing
H 50mm Diameter x 4mm thick tubular handrail m 98 21.00 2,058.00
J Extra over for bend no. 52 9.60 499.20
K Ditto for stopped end no. 4 9.60 38.40
L 19mm x 6mm Thick as mild steel flat as

bottom rail m 98 3.00 294.00
M Extra over for bend no. 32 3.00 96.00
N 30mm x 30mm x 3mm Thick SHS as main

baluster 900mm long one end welded to and
including 125mm x 60mm x 4mm mild steel
base plate welded to stair reinforcement
and other end welded to 50mm diameter mild
steel tabular handrail (measured
separately) no. 136 8.00 1,088.00
BQ/5/2

(CONT'd)

FINISHES (CONT'd)
Staircase Railing (CONT'd)
A 15mm x 15mm x 1.6mm Thick SHS as baluster

670mm long one end welded to 50mm diameter
mild steel tubular handrail and other end
welded to mild steel flat bottom rail (both
measured separately) no. 496 12.40 6,150.40
B 100mm x 75mm x 5mm Connecting plate

anchored to brick wall with bolts (measured
separately) no. 4 2.40 9.60
C 13mm Diameter bolt 100mm long, once bent

with head, nut and washers including
drilling through 5mm connecting plate
(measured separately) no. 8 2.90 23.20
Corridor Railing
D 19mm x 6mm Thick as mild steel flat as

bottom rail m 98 3.00 294.00
E 100mm x 50mm x 3.2m Thick RHS as handrail m 240 31.00 7,440.00
F 25mm x 25mm x 2.3mm Thick SHS as main

baluster 900mm long one end welded to 100mm
x 50mm x 2mm thick RHS handrail and other
end welded to mild steel flat bottom rail
(both measured separately) no. 1,760 5.50 9,680.00
G 150mm x 75mm x 4mm Connecting plate

anchored to brick wall with bolts (measured
separately) no. 160 2.00 320.00
H 13mm Diameter bolt 100mm long, once bent

with head, nut and washers including
drilling through 4mm connecting plate no. 320 2.00 640.00
Cement and sand (1:4) mixed with an

approved plasticiser internally as
described to
J 19mm Plain face to sloping soffit of

staircase m2 96 10.50 1,008.00
K 19mm Ditto to soffit of suspended landing

slab and sides and soffit of landing beam m2 87 10.50 913.50
BQ/5/3

(CONT'd)

FINISHES (CONT'd)

described to (CONT'd)
A 19mm Ditto to string of staircase m2 80 10.50 840.00
Prepare and apply one undercoat and two

coats emulsion paint on the following
plastered surfaces
B Sloping soffit of staircase m2 96 2.90 278.40
C Soffit of suspended landing slab and sides

and soffit of landing beam m2 87 2.90 252.30
D String of staircase m2 80 1.00 80.00
Prepare and apply one coat metallic primer

general surfaces of metalwork
Staircase Railing
E General surfaces of small pipe m 98 1.00 98.00
F General surfaces not exceeding 100mm girth m 424 0.60 254.40
G Ditto exceeding 100mm and not exceeding

200mm girth m 123 1.20 147.60
Prepare and apply one coat metallic primer

general surfaces of metalwork
Corridor Railing
H General surfaces not exceeding 100mm girth m 2,384 0.60 1,430.40
J Ditto exceeding 200mm and not exceeding

300mm girth m 240 1.80 432.00
BQ/5/4
Description Amount
Collection
Page No. BQ/5/1 12,808.24
Page No. BQ/5/2 14,545.00
Page No. BQ/5/3 26,478.70
Page No. BQ/5/4 3,813.10
BQ/5/5
EXTERNAL WALLS
EXTERNAL WALLS
ELEMENT NO. 7 - EXTERNAL WALLS
A Reinforced concrete Grade 25 as described

in stiffener m3 4 159.00 636.00
B 6mm Diameter mild steel bar reinforcement

as described links in stiffener kg 197 1.66 327.02
C 10mm Diameter high yield steel bar

reinforcement as described in stiffener kg 355 1.64 582.20
D Sawn formwork as described to sides of

stiffener m2 87 17.00 1,479.00
Brickwork in cement and sand bricks as

described in composition mortar as
described
E Half-brick wall reinforced with and

including brick reinforcement as described m2 3,243 20.00 64,860.00
F Ditto as balustrade wall m2 1,079 20.00 21,580.00
Brickwork in common bricks as described in

composition mortar as described
G Half-brick wall in common brick as

described reinforced with and including
brick reinforcement as described m2 626 24.00 15,024.00
H One-brick wall in common brick as described m2 58 48.00 2,784.00
J Ditto as balustrade wall m2 64 48.00 3,072.00
K Horizontal damp proof course as described

laid on half brick wall well lapped at
joints and junctions (measured nett - no
allowance made for laps) m 22 1.90 41.80
L Ditto one-brick wall (ditto) m 222 3.80 843.60
M 6mm Diameter mild steel as described

bonding tie 450mm girth one end hooked and
cast in concrete and other end built into
joints of brickwork including perforation
in formwork no. 11,760 1.00 11,760.00
N 75mm Diameter PVC pipe 150mm built into

joints of brickwork including wrapping at
end with selected filter material no. 32 3.00 96.00
BQ/6/1
EXTERNAL WALLS
Description Amount
EXTERNAL WALLS
Collection
Page No. BQ/6/1 123,085.62
BQ/6/2
INTERNAL WALLS AND PARTITIONS
ELEMENT NO. 8 - INTERNAL WALLS AND

PARTITIONS

in stiffener m3 22 159.00 3,498.00

as described links in stiffener kg 1,220 1.66 2,025.20

reinforcement as described in stiffener kg 2,307 1.64 3,783.48
D Sawn formwork as described to sides of

stiffener m2 562 17.00 9,554.00
E Half-brick wall in cement and sand bricks

as described in composition mortar as
brick reinforcement as described m2 7,090 20.00 141,800.00
F Ditto as balustrade wall m2 3 20.00 60.00
G Half-brick wall in common bricks as

described in composition mortar as
brick reinforcement as described m2 3,546 24.00 85,104.00
H Horizontal damp proof course as described

laid on half-brick wall well lapped at
joints and junctions (measured nett - no
allowance made for laps) m 80 1.90 152.00
J 6mm Diameter mild steel as described

bonding tie 450mm girth one end hooked and
cast in concrete and other end built into
joints of brickwork including perforation
in formwork no. 10,800 1.00 10,800.00
BQ/7/1
Description Amount
Collection
Page No. BQ/7/1 256,776.68
BQ/7/2
WINDOWS
WINDOWS
ELEMENT NO. 9 - WINDOWS

in
A Lintol m3 36 159.00 5,724.00
B Hood m3 5 159.00 795.00
Mild steel bar reinforcement as described
C 8mm Diameter as stirrups in lintol kg 2,452 1.66 4,070.32
D 10mm Diameter in hood kg 557 1.66 924.62

described in lintol
E 12mm Diameter kg 1,696 1.64 2,781.44
F 10mm Ditto kg 1,176 1.64 1,928.64
G Sides and soffit of lintol m2 430 17.00 7,310.00
H Sides and soffit of hood m2 80 17.00 1,360.00
J 15mm x 75mm Sawn pressure treated Group 'B'

timber as described packing piece plugged
and screwed to brickwork or concrete m 4,429 1.60 7,086.40
Wrot Group 'A' timber as described
K 44mm x 100mm Frame m 1,824 10.50 19,152.00
L 44mm x 100mm Mullion m 1,392 10.50 14,616.00
M 44mm x 119mm Frame, once rebated and

throated m 1,374 11.00 15,114.00
N 45mm x 119mm Frame, twice rebated m 432 11.00 4,752.00
P 44mm x 144mm Sill, once rebated, sunk

weathered and throated m 1,214 12.00 14,568.00
Q 16mm x 19mm Wrot pressure treated Group 'C'

beading m 864 1.50 1,296.00
R Form 13mm deep sloping grooves across grain

of timber for ends of 5mm x 150mm glass
louvre blade (measured separately) no. 5,440 0.50 2,720.00
BQ/8/1
WINDOWS
WINDOWS (CONT'd)
ELEMENT NO. 9 - WINDOWS (CONT'd)
Wrot Group 'A' timber as described (CONT'd)
A Pair galvanised steel aluminium laccquered

finish adjustable louvre frame 1114mm high
each with clips of 8 Nos. 150mm wide glass
louvre blade (measured separately) complete
with 1 No. friction lock handle and screwed
to timber frame no. 1,600 12.00 19,200.00
B Pair ditto with clips of 5 Nos. 150mm wide

glass louvre blade (measured separately)
ditto no. 320 7.50 2,400.00
C Pair ditto with clips of 3 Nos. 150mm wide

glass louvre blade (ditto) ditto no. 640 4.50 2,880.00
Supply, deliver to site and fix the

following natural anodised aluminium
windows as described infilled with glass
(measured separately) including all
necessary frames, sub-frames, transome,
mullions, glazing materials, glazing beads,
fixing screws, ironmongery and accessories
Tenderer To Note:
The sizes are only as a guide in tendering

and the tenderer shall supply all the units
in accordance with site measurements and no
claims will be entertained for any
discrepancy between the Drawings, Bills of
Quantities and Site Measurement
Rates for aluminium works shall include all

cutting and waste, cutting holes for
electrical wiring and conduits, etc.
D Aluminium adjustable louvred window overall

size 1200mm x 700mm high (LW1) no. 1 195.00 195.00
E Aluminium adjustable louvred window overall

size 2900mm x 700mm high comprising 3 No.
panels each size 967mm x 700mm high (LW3) no. 2 377.00 754.00
F Aluminium adjustable louvred window overall

size 3508mm x 700mm high comprising 3 No.
panels each size 877mm x 700mm high (LW2) no. 2 430.00 860.00
BQ/8/2
WINDOWS
WINDOWS (CONT'd)
ELEMENT NO. 9 - WINDOWS (CONT'd)
Tenderer To Note: (CONT'd)
A 3mm x 32mm Thick holdfast 229mm girth once

bent, twice holed and screwed to timber
frame and other end fishtailed and built
into joints of brickwork including priming
before fixing no. 5,120 1.00 5,120.00
B 12mm Diameter mild steel as described

security bar and fixed through timber frame
(In No. 6816) m 10,353 2.80 28,988.40
C 5mm Thick obscured glass louvre blades

150mm wide with polished and ground edges
and fixing into grooves in timber frame
(grooves measured separately) m 480 4.40 2,112.00
D 5mm Thick clear glass louvre blades 150mm

wide ditto (ditto) m 9,943 5.00 49,715.00
E Prepare and apply one coat dull aluminium

wood primer before fixing on back of timber
frame exceeding 100mm and not exceeding
200mm girth m 4,269 1.00 4,269.00
F Knot with gold size, stop, prime with dull

aluminium wood primer and apply three coats
alkyd resin based paint as described on
general surfaces of woodwork exceeding
100mm and not exceeding 200mm girth m 3,216 1.15 3,698.40
G Ditto exceeding 200mm and not exceeding

300mm girth m 3,020 1.70 5,134.00
H Prepare and apply one coat metallic primer

and three alkyd resin based paint as
described on general surfaces of metalwork
not exceeding 100mm girth m 10,353 0.60 6,211.80
BQ/8/3
WINDOWS
Description Amount
WINDOWS
Collection
Page No. BQ/8/1 104,198.42
Page No. BQ/8/2 26,289.00
Page No. BQ/8/3 105,248.60
BQ/8/4
DOORS
DOORS
ELEMENT NO. 10 - DOORS

in lintol m3 22 159.00 3,498.00

as described stirrups in lintol kg 266 1.66 441.56

reinforcement as described in lintol kg 1,949 1.64 3,196.36
D 10mm Ditto kg 1,352 1.64 2,217.28
E Sawn formwork as described to sides and

soffit of lintol m2 429 17.00 7,293.00
F 38mm Thick skeleton framed flush door in

wrot pressure treated Group 'B' timber as
described covered on both sides with 6mm
thick plywood as described with and
including 26mm x 38mm wrot Group 'A' timber
as described rebated lipping all round
mitred at angles and hanging on butt hinges
(measured separately and In No. 802 ) m2 1,326 38.20 50,653.20
G Pair 51mm one - hour fire rated door

overall size 830mm x 2065mm high in wrot
Group 'A' timber as described to the
approval of the Director General of Fire
Services Malaysia and hanging on butt
hinges (measured separately) no. 10 370.00 3,700.00
H 15mm x 75mm Sawn pressure treated Group 'B'

timber as described packing piece plugged
and screwed to brickwork or concrete m 5,331 1.60 8,529.60
J 44mm x 100mm Wrot Group 'A' timber as

described frame, once rebated m 5,027 11.00 55,297.00
K 44mm x 138mm Wrot Group 'A' timber as

described frame, twice rebated m 496 12.50 6,200.00
L 38mm Approved G.I. sheet door overall size

680mm x 2065mm high constructed in
galvanised hollow section framing and 1.2mm
galvanised iron sheet and hanging on and
including butt hinges (ironmongery measured
separately) (D2) no. 320 50.00 16,000.00
BQ/9/1
DOORS
DOORS (CONT'd)
ELEMENT NO. 10 - DOORS (CONT'd)
A Supply and install 65mm x 140mm

electro-galvanised steel 1.2mm thick door
frame as 'JIS G3313 SECC-P' or other equal
and approved with and including 3 Nos. pair
127mm x 90mm x 2.3mm stainless steel hinges
spot welded into vertical slot opening of
door frame complete with brick
ties/adaptor, striker plate, spreader bar,
bracket cushioning rubber stop and all
necessary backing plate and fixing screws
including all necessary cement and sand
(1:3) mortar infill and joint finishing to
suit opening size 1200mm x 2100mm high for
double leave one-hour fire rated door no. 10 137.00 1,370.00
Supply and fix the following ironmongery of

the type specified or other equal and
approved to timber/steel including all
necessary matching screws unless otherwise
described
B Pair 'REX' 100mm x 75mm nylon ring hinges no. 963 8.00 7,704.00
C Yale MY 5107-G13-US32D Entrance Knobset no. 800 31.00 24,800.00
D Yale MY 5102-G13-US32D Bathroom Knobset no. 320 29.00 9,280.00
E Yale PM444-C13 Security bolt no. 12 25.70 308.40
F Ditto rebated set no. 10 6.70 67.00
G 100mm Aluminium D handle no. 10 6.80 68.00
H 40mmm Diameter rubber stopper no. 960 1.90 1,824.00
J 'REX' 150mm x 50mm Stainless steel flush

bolt no. 10 10.50 105.00
K 'REX' 300mm x 50mm Stainless steel flush

bolt no. 10 13.80 138.00
L 3mm x 32mm Holdfast 229mm once bent, one

end fixed to sides of timber frame and
other end fishtailed and built into joints
of brickwork no. 8,656 1.00 8,656.00
M Prepare and apply one coat dull aluminium

wood primer as described before fixing on
back of timber exceeding 100mm and not
exceeding 200mm girth m 5,291 1.00 5,291.00
BQ/9/2
DOORS
DOORS (CONT'd)
ELEMENT NO. 10 - DOORS (CONT'd)
Knot, prime, stop with dull aluminium wood

primer and apply one undercoat and two
coats alkyd resin based paint on
A General surfaces of door m2 2,828 4.80 13,574.40
B Ditto on fire rated door m2 52 4.80 249.60
C General surfaces of timber exceeding 100mm

and not exceeding 200mm girth m 4,795 1.15 5,514.25
D Ditto exceeding 200mm and not exceeding

300mm girth m 496 1.70 843.20
E Prepare and apply one coat metallic primer

general surfaces of metal exceeding 200mm
and not exceeding 300mm girth m 54 1.75 94.50
BQ/9/3
DOORS
Description Amount
DOORS
Collection
Page No. BQ/9/1 157,026.00
Page No. BQ/9/2 59,611.40
Page No. BQ/9/3 20,275.95
BQ/9/4
INTERNAL WALL FINISHES
ELEMENT NO. 11 - INTERNAL WALL FINISHES
A 18mm Cement and sand (1:3) backing screed

to receive glazed wall tiles (measured
separately) to wall and column m2 2,492 6.20 15,450.40
B 19mm Cement and sand (1:4) mixed with an

described plain face to wall and column m2 28,031 8.60 241,066.60
C 19mm Ditto to side of balustrade wall m2 910 8.60 7,826.00
D 150mm x 150mm x 6mm Thick glazed ceramic

wall tiles as 'Guocera Monochrome
Monoporosa' or other equal and approved
bedded and jointed in cement mortar (1:3)
as described and pointed in tinted cement
to match to wall and column m2 2,492 35.00 87,220.00
E Prepare and apply one coat alkali resisting

primer and two coats emulsion paint as
described on plastered walls and columns m2 28,031 2.80 78,486.80
F Ditto to side of balustrade wall m2 1,141 2.80 3,194.80
BQ/10/1
Description Amount
Collection
Page No. BQ/10/1 433,244.60
BQ/10/2
INTERNAL FLOOR FINISHES
ELEMENT NO. 12 - INTERNAL FLOOR FINISHES
A 30mm Paving trowelled smooth to floor m2 9,888 8.60 85,036.80
B 30mm Ditto laid to falls and crossfalls m2 2,355 8.60 20,253.00
C 26mm Ditto to sides and base of scupper

drain m2 145 5.25 761.25
D 26mm Screed to floor to receive mosaic

tiles (measured separately) m2 511 5.25 2,682.75
E 15mm Screed to top and sides of kerb to

receive mosaic tiles (ditto) m2 286 4.00 1,144.00
F 15mm Paving to riser 50mm high m 2 3.00 6.00
G 15mm Ditto 100mm high m 147 3.80 558.60
H Supply and lay two coats 'Sikatop Seal 107'

or other equal and approved cementitious
waterproofing system as described at a rate
of 1 Kg/m2 per coat all in accordance with
manufacturer's instructions to floor m2 511 24.00 12,264.00
J Ditto to top and sides of kerb m 286 12.00 3,432.00
K Ditto skirting 100mm high m 1,613 3.00 4,839.00
L 18.5mm x 18.5mm x 4.5mm Thick homogeneous

mosaic tiles as MML Vintage or other equal
and approved, bedded and jointed in cement
mortar (1:3) as described and pointed with
coloured cement to match and in accordance
with the Architect's pattern to floor to
falls m2 511 32.00 16,352.00
M 18.5mm x 18.5mm x 4.5mm Ditto to top and

sides of kerb including forming coved tiles
to edges m2 77 32.00 2,464.00
BQ/11/1
Description Amount
Collection
Page No. BQ/11/1 149,793.40
BQ/11/2
INTERNAL CEILING FINISHES
ELEMENT NO. 13 - INTERNAL CEILING FINISHES
A 50mm x 50mm Sawn pressure treated Group 'B'

timber as described nogging m 1,624 2.75 4,466.00
B 50mm x 75mm Ditto ceiling joist m 1,668 2.75 4,587.00
C 50mm x 75mm Ditto Bearer m 3,507 2.75 9,644.25
D 50mm x 13mm Thick wrot pressure treated

Group 'C' timber as described decorative
moulded beading as per Drawing No. D6.1
detail 'Z' m 6,797 2.50 16,992.50
E 3.2mm Cement building sheet ceiling as

'UAC-Superflex' or other equal and approved
in 1220mm x 1220mm panel set out
symmetrically from the centre of the room
and fixed to timber framing (measured
separately) (The rate shall include for odd
panels at borders of room) m2 2,489 7.50 18,667.50
F Extra over for forming access panel size

1220mm x 1220mm including all additional
trimming and beading no. 206 12.00 2,472.00
G 3mm 'Vetonit' or other equal and approved

cement based ready-mixed plaster applied to
concrete soffit and sides and soffit of
beam in accordance with manufacturer's
instructions including touching up concrete
surfaces m2 11,144 4.25 47,362.00
H Prepare and apply three coats of emulsion

paint on general surfaces of cement
building sheet m2 2,489 2.80 6,969.20
J Prepare and apply one coat emulsion paint

as described on 'Vetonit' plastered
concrete soffit and sides and soffit of
beams m2 11,144 1.70 18,944.80
K Knot with gold size, stop, prime with dull

alkyd resin based paint as described on
surfaces of timber beads not exceeding
100mm girth m 6,797 0.60 4,078.20
BQ/12/1
Description Amount
Collection
Page No. BQ/12/1 134,183.45
BQ/12/2
EXTERNAL FINISHES
EXTERNAL FINISHES
ELEMENT NO. 14 - EXTERNAL FINISHES
A 28mm Paving trowelled smooth to floor m2 135 7.70 1,039.50
B 15mm Ditto to riser 150mm high m 5 3.00 15.00

approved plasticiser externally as
described
C 19mm Plainface to wall and column m2 4,551 9.00 40,959.00
D 19mm Plainface to top and sides of

balustrade wall m2 1,270 9.00 11,430.00
E 19mm Ditto to top, sides and soffit of hood m2 137 9.00 1,233.00
F 50mm x 50mm Sawn pressure treated Group `B'

timber as described nogging m 1,190 2.75 3,272.50
G 13mm x 50mm Wrot pressure treated Group `C'

timber as described bead m 1,190 2.50 2,975.00
H 3.2mm Cement building sheet as

'UAC-Superflex' or other equal and approved
in 610mm x 610mm panel set out
symmetrically from the centre of the
building and fixed to timber framing
(measured separately) exceeding 13.50m and
not exceeding 15.00m high m2 233 7.50 1,747.50
J Prepare and apply one coat alkali resisting

primer and two coats of emulsion paint on
general surfaces of cement building sheet
ceiling m2 233 2.80 652.40
Prepare and apply three coats 'Par

Weathercoat' or other equal and approved
paint as described on the following
surfaces
K Plastered wall and column m2 4,551 4.30 19,569.30
L Plastered top and sides of balustrade wall m2 1,270 4.30 5,461.00
M Plastered top, sides and soffit of hood m2 137 4.30 589.10
N Knot with gold size, stop, prime with dull

alkyd resin based paint on general surfaces
of woodwork not exceeding 100mm girth m 1,190 0.60 714.00
BQ/13/1
EXTERNAL FINISHES
Description Amount
EXTERNAL FINISHES
Collection
Page No. BQ/13/1 89,657.30
BQ/13/2
PLUMBING SERVICES &SANITARY FITTINGS
ELEMENT NO. 15 - PLUMBING SERVICES &

SANITARY FITTINGS
COLD WATER, SOIL AND WASTE WATER PLUMBING
Provide the P.C. Sum of Ringgit Two Hundred

And Ninety Thousand Only (RM 290,000.00)
for Plumbing And Sanitary Service to be
executed by a firm to be nominated by the
Architect
Allow for profit
Allow for attendance as described in

`Preliminaries' upon the Nominated
Sub-Contractor executing the above
SANITARY FITTINGS
Supply and fix the following sanitary

fittings of the type specified or other
equal and approved in standard colour
vitreous china unless otherwise stated
including all joints and connection to
supply, waste and overflow pipe where
necessary
A 150mm x 150mm Semi-recessed toilet roll

holder as `Claytan (Globe) Ref TA502'
complete with plastic roller including
setting in tiled wall in cement and sand
(1:3) mortar as described no. 160 16.50 2,640.00
B 150mm x 150mm Semi-recessed soap holder as

`Claytan (Globe) Ref. TA501' including
setting in tiled wall in cement and sand
(1:3) mortar as described no. 160 16.50 2,640.00
C 510mm x 406mm Wall hung wash hand basin as

`Claytan (Globe) Ref. WB704' complete with
15mm diameter `Premtex Ref. PRM-PLT2-90'
chromium plated pillar tap with acrylic
handle, 32mm diameter waste plug and chain
and 32mm diameter chromium plated plastic
bottle trap and including plugging and
screwing bracket to tiled wall no. 160 105.00 16,800.00
BQ/14/1

(CONT'd)

SANITARY FITTINGS (CONT'd)

necessary (CONT'd)
A Washdown pedestal water closet as `Claytan

(Globe) Ref. ST202' complete with S-trap,
light duty seat and cover, `Pakai- Mayor'
low level plastic cistern with lid, 12mm
ball valve to B.S. 1212, 20mm diameter
overflow pipe and plastic flush bend
supporting brackets and rubber joint
including plugging and screwing cistern
supporting brackets to tiled wall and pan
to tiled floor and jointing flush pipe to
cistern and pan no. 160 134.00 21,440.00
B Shower fitting comprising `DKI S303 '

chromium plated ball joint shower rose and
`S-301' arm, 15mm diameter F+F concealed
stopcock and `Premtex-SVC2-90' acrylic
handle and fixed to tiled wall no. 160 33.50 5,360.00
C 15mm Diameter `Premtex-PRM-HBR4-T2' bib tap

in rough chromium plated tap handle
including fixing to inlet no. 160 15.30 2,448.00
D Single bowl single drainer aluminium

kitchen sink as `TML Ref 42/18' overall
size 1080mm x 470mm with 1 No. 38mm
diameter stainless steel waste outlet, 1No.
15mm diameter `Premtex PRM-STW1-90'
chromium plated wall mounted sink tap with
swivel nozzle and matching wall flange with
acrylic handle, 1 No. 38mm diameter
chromium plated PVC bottle trap with and
including plugging and screwing bracket to
wall no. 160 107.00 17,120.00
BQ/14/2

(CONT'd)


necessary (CONT'd)
A On completion of the Plumbing Installation

and Sanitary Fittings test all piping for
water tightness, make good any defects and
leave everything in perfect working order
to the entire satisfaction of the Architect
and Local Authorites item
To Collection (MYR) 0.00
BQ/14/3
Description Amount
Collection
Page No. BQ/14/1 22,080.00
Page No. BQ/14/2 46,368.00
Page No. BQ/14/3 0.00
BQ/14/4
MECHANICAL & ELECTRICAL INSTALLATION
ELEMENT NO. 16 - MECHANICAL AND ELECTRICAL

INSTALLATION
ELECTRICAL SERVICES
A Provide the P.C. Sum of Ringgit Four

Hundred And Sixty Thousand Only (RM
460,000.00 for ELECTRICAL SERVICES to be
executed by a firm to be nominated by the
Architect LS - - 10,000.00
B Allow for profit % 5 - 500.00
C Allow for attendance as described in

Sub-Contractor executing the above % 5 - 500.00
TELEPHONE SERVICES
D Provide the P.C. Sum of Ringgit One Hundred

And Twelve Thousand Only (RM 112,000.00)
for TELEPHONE SERVICES to be executed by a
firm to be nominated by the Architect LS - - 10,000.00
E Allow for profit % 5 - 500.00
F Allow for attendance as described in

MATV INSTALLATION
G Provide the P.C. Sum of Ringgit One Hundred

Thousand Only (RM 100,000.00) for MATV
INSTALLATION to be executed by a firm to be
nominated by the Architect LS - - 10,000.00
H Allow for profit % 5 - 500.00
J Allow for attendance as described in

'Preliminaries' upon the Nominated
BQ/15/1
Description Amount
Collection
Page No. BQ/15/1 33,000.00
BQ/15/2
BUILDER'S WORK
BUILDER'S WORK
ELEMENT NO. 17 - BUILDER'S WORK IN

CONNECTION WITH SERVICES
A 75mm Thick reinforced concrete Grade 25 as

described in letter box plinth m2 4 11.92 47.68
B 115mm x 75mm High reinforced concrete Grade

25 as described in kerb m 464 1.37 635.68
C 10mm Diameter mild steel bar reinforcement

as described in kerb kg 1,068 1.66 1,772.88
D Sawn formwork as described to edge of

concrete not exceeding 100mm high m 928 2.30 2,134.40
E 75mm x 75mm x 6mm Thick mild steel angle

cast in concrete or brickwork kg 4,341 4.50 19,534.50
F 10mm Thick plywood as described decking

fixed on steel trusses m2 225 30.00 6,750.00
G Layer of steel fabric reinforcement to B.S.

4483 as described (BRC Ref. No. A6 -
weighing not less than 2.22kg per m2) well
lapped at joints and embedded in concrete
bed (measured nett - no allowance made for
laps) m2 4 6.70 26.80
H Sawn formwork as described to soffit of

letter box plinth and left in m2 4 17.00 68.00
J Ditto to edge of concrete not exceeding

100mm girth m 17 2.30 39.10
K Half-brick wall in cement sand bricks in

composition mortar as described with and
including brick reinforcement as described
plinth support m2 7 20.00 140.00
L 19mm Cement and sand (1:4) mixed with an

approved plasticiser as described plainface
to sides of plinth support m2 8 8.60 68.80
M Prepare and apply one coat alkali resisting

primer and two coats approved emulsion
paint as described on plastered sides of
plinth support m2 8 2.90 23.20
BQ/16/1
BUILDER'S WORK
Description Amount
BUILDER'S WORK
Collection
Page No. BQ/16/1 31,241.04
BQ/16/2
LETTER BOXES AND SIGNS
ELEMENT NO. 18 - LETTER BOXES AND SIGNS
A Supply and install aluminium composite

letter box unit overall size 1150mm
(extreme) x 430mm x 820mm (extreme) high
comprising 20 units letter box each size
230mm x 430mm x 205mm high in 18 Nos. of 5
vertical tiers, each unit complete with
doors, posting apertures and visible
frames, aluminium internal frames, letter
box locker and engraved numberings and
fixed to top of concrete/brick platform
(measured separately) including all fixing
accessories no. 8 330.00 2,640.00
B Supply and install signs for 'ALURAN

ELEKTRIK' overall size 80mm x 300mm the
following signs and directories including
all fixing screws and accessories no. 10 9.55 95.50
C Prepare and apply two coats emulsion paint

as Unit Number overall size 80mm x 200mm no. 160 3.00 480.00
BQ/17/1
Description Amount
Collection
Page No. BQ/17/1 3,215.50
BQ/17/2

Single BQ

Uploaded by

Copyright:

Available Formats

Single BQ

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Single BQ

Uploaded by

Copyright:

Available Formats

Summary

Description Page No Amount

WORK BELOW LOWEST FLOOR FINISH BQ/1/4 230,694.60

FRAME BQ/2/8 441,488.20

UPPER FLOOR BQ/3/2 507,277.98

ROOF BQ/4/8 202,915.35

STAIRS, RAMPS AND STAIRCASE FINISHES BQ/5/5 57,645.04

EXTERNAL WALLS BQ/6/2 123,085.62

INTERNAL WALLS AND PARTITIONS BQ/7/2 256,776.68

WINDOWS BQ/8/4 235,736.02

DOORS BQ/9/4 236,913.35

INTERNAL WALL FINISHES BQ/10/2 433,244.60

INTERNAL FLOOR FINISHES BQ/11/2 149,793.40

INTERNAL CEILING FINISHES BQ/12/2 134,183.45

EXTERNAL FINISHES BQ/13/2 89,657.30

PLUMBING SERVICES &SANITARY FITTINGS BQ/14/4 68,448.00

MECHANICAL & ELECTRICAL INSTALLATION BQ/15/2 33,000.00

BUILDER'S WORK BQ/16/2 31,241.04

LETTER BOXES AND SIGNS BQ/17/2 3,215.50

Total Per Unit (MYR) 3,235,316.13

WORK BELOW LOWEST FLOOR FINISH

ELEMENT NO. 2 - WORK BELOW LOWEST FLOOR

Excavate, get out, part return, fill in and

A Oversite to reduce level m3 824 11.00 9,064.00

B Pile cap not exceeding 1.50m deep including

C Ground beam not exceeding 1.50m deep m3 71 9.00 639.00

D Trench not exceeding 1.50m deep m3 24 9.00 216.00

E Prepare and apply 'Simechem' or other equal

F 100mm Bed of hardcore as described spread,

50mm Concrete Grade 10 as described

H Ground beam m2 272 7.40 2,012.80

J 150mm Base m2 20 7.40 148.00

K 100mm Bed m2 2,288 7.40 16,931.20

Reinforced concrete Grade 25 as described

L Ground beam m3 125 159.00 19,875.00

M 150mm Base m2 20 23.85 477.00

N 150mm Wall m2 44 23.85 1,049.40

P 100mm Bed m2 2,288 15.90 36,379.20

To Collection (MYR) 106,973.20

WORK BELOW LOWEST FLOOR FINISH (CONT'd)

ELEMENT NO. 2 - WORK BELOW LOWEST FLOOR

Reinforced concrete Grade 25 as described

A Extra over for thicknessing to an

B Ditto to an average width of 650mm and to a

C Reinforced concrete Grade 30 as described

Mild steel bar reinforcement as described

D 10mm Diameter as column starter bar links kg 1,308 1.66 2,171.28

E 10mm Diameter as stirrups in ground beam kg 129 1.66 214.14

F 8mm Ditto kg 3,165 1.66 5,253.90

High yield steel bar reinforcement as

G 20mm Diameter kg 2,901 1.55 4,496.55

H 16mm Ditto kg 8,905 1.55 13,802.75

J 12mm Ditto kg 5,052 1.64 8,285.28

K 10mm Ditto kg 125 1.64 205.00

Column Starter Bar

L 20mm Diameter kg 4,049 1.55 6,275.95

M 16mm Ditto kg 3,429 1.55 5,314.95

N 16mm Diameter kg 454 1.55 703.70