License #3010*1PGKAJSQP7BM4DY

SAP2000 Analysis Report

Prepared by
YOSEP SUHUN
15041000054

Model Name: TUGAS YOSEP.sdb

6 November 2018
TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

Contents
1. Model geometry........................................................................................................................................................ 5
1.1. Joint coordinates............................................................................................................................................... 5
1.2. Joint restraints................................................................................................................................................... 6
1.3. Element connectivity......................................................................................................................................... 6
2. Material properties.................................................................................................................................................... 7
3. Section properties..................................................................................................................................................... 8
3.1. Frames.............................................................................................................................................................. 8
3.2. Solids................................................................................................................................................................ 9
4. Load patterns............................................................................................................................................................ 9
4.1. Definitions......................................................................................................................................................... 9
5. Load cases.............................................................................................................................................................. 10
5.1. Definitions....................................................................................................................................................... 10
5.2. Static case load assignments.......................................................................................................................... 10
5.3. Response spectrum case load assignments................................................................................................... 10
6. Load combinations.................................................................................................................................................. 11
7. Structure results...................................................................................................................................................... 12
7.1. Mass summary................................................................................................................................................ 12
7.2. Modal results................................................................................................................................................... 13
7.3. Base reactions................................................................................................................................................ 13
8. Joint results............................................................................................................................................................. 14
9. Frame results.......................................................................................................................................................... 15
10. Material take-off.................................................................................................................................................... 24
11. Design preferences............................................................................................................................................... 24
11.1. Steel design................................................................................................................................................... 24
11.2. Concrete design............................................................................................................................................ 25
11.3. Aluminum design........................................................................................................................................... 25
11.4. Cold formed design....................................................................................................................................... 25

List of Figures
Figure 1: Finite element model...................................................................................................................................... 5
Figure 2: Deformed shape........................................................................................................................................... 12

List of Tables
Table 1: Joint Coordinates............................................................................................................................................. 5
Table 2: Joint Restraint Assignments............................................................................................................................ 6
Table 3: Connectivity - Frame........................................................................................................................................ 6
Table 4: Frame Section Assignments............................................................................................................................ 6
Table 5: Material Properties 02 - Basic Mechanical Properties..................................................................................... 7
Table 6: Material Properties 03a - Steel Data................................................................................................................ 7
Table 7: Material Properties 03b - Concrete Data......................................................................................................... 7
Table 8: Material Properties 03e - Rebar Data.............................................................................................................. 7
Table 9: Material Properties 03f - Tendon Data............................................................................................................. 7
Table 10: Frame Section Properties 01 - General, Part 1 of 4....................................................................................... 8
Table 10: Frame Section Properties 01 - General, Part 2 of 4....................................................................................... 8
Table 10: Frame Section Properties 01 - General, Part 3 of 4....................................................................................... 8
Table 10: Frame Section Properties 01 - General, Part 4 of 4....................................................................................... 8
Table 11: Frame Section Properties 02 - Concrete Column, Part 1 of 2........................................................................ 8
Table 11: Frame Section Properties 02 - Concrete Column, Part 2 of 2........................................................................ 9

YOSEP SUHUN Page 3 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

Table 12: Frame Section Properties 03 - Concrete Beam, Part 1 of 2........................................................................... 9
Table 12: Frame Section Properties 03 - Concrete Beam, Part 2 of 2........................................................................... 9
Table 13: Solid Property Definitions.............................................................................................................................. 9
Table 14: Load Pattern Definitions................................................................................................................................ 9
Table 15: Load Case Definitions, Part 1 of 2............................................................................................................... 10
Table 15: Load Case Definitions, Part 2 of 2............................................................................................................... 10
Table 16: Case - Static 1 - Load Assignments............................................................................................................. 10
Table 17: Function - Response Spectrum - User......................................................................................................... 10
Table 18: Combination Definitions............................................................................................................................... 11
Table 19: Assembled Joint Masses, Part 1 of 2........................................................................................................... 12
Table 19: Assembled Joint Masses, Part 2 of 2........................................................................................................... 13
Table 20: Modal Participating Mass Ratios................................................................................................................. 13
Table 21: Base Reactions........................................................................................................................................... 13
Table 22: Joint Displacements..................................................................................................................................... 14
Table 23: Joint Reactions............................................................................................................................................ 14
Table 24: Element Forces - Frames, Part 1 of 2.......................................................................................................... 15
Table 24: Element Forces - Frames, Part 2 of 2.......................................................................................................... 19
Table 25: Material List 2 - By Section Property............................................................................................................ 24
Table 26: Preferences - Steel Design - AISC 360-10, Part 1 of 4................................................................................ 24
Table 26: Preferences - Steel Design - AISC 360-10, Part 2 of 4................................................................................ 24
Table 26: Preferences - Steel Design - AISC 360-10, Part 3 of 4................................................................................ 24
Table 26: Preferences - Steel Design - AISC 360-10, Part 4 of 4................................................................................ 25
Table 27: Preferences - Concrete Design - ACI 318-14, Part 1 of 2............................................................................ 25
Table 27: Preferences - Concrete Design - ACI 318-14, Part 2 of 2............................................................................ 25
Table 28: Preferences - Aluminum Design - AA-ASD 2000......................................................................................... 25
Table 29: Preferences - Cold Formed Design - AISI-ASD96....................................................................................... 25

YOSEP SUHUN Page 4 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

1. Model geometry
This section provides model geometry information, including items such as joint coordinates, joint restraints, and
element connectivity.

Figure 1: Finite element model

1.1. Joint coordinates

Table 1: Joint Coordinates

Table 1: Joint Coordinates
Joint CoordSys CoordType GlobalX GlobalY GlobalZ
cm cm cm
1 GLOBAL Cartesian 0. 0. 0.
2 GLOBAL Cartesian 0. 0. 600.
3 GLOBAL Cartesian 0. 0. 1000.
4 GLOBAL Cartesian 0. 0. 1400.
5 GLOBAL Cartesian 600. 0. 0.
6 GLOBAL Cartesian 600. 0. 600.
7 GLOBAL Cartesian 600. 0. 1000.
8 GLOBAL Cartesian 600. 0. 1400.
9 GLOBAL Cartesian 1000. 0. 200.
10 GLOBAL Cartesian 1000. 0. 600.
11 GLOBAL Cartesian 1000. 0. 1000.

YOSEP SUHUN Page 5 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

1.2. Joint restraints

Table 2: Joint Restraint Assignments

Table 2: Joint Restraint Assignments
Joint U1 U2 U3 R1 R2 R3

1 Yes Yes Yes Yes Yes Yes

5 Yes Yes Yes Yes Yes Yes
9 Yes Yes Yes Yes Yes Yes

1.3. Element connectivity

Table 3: Connectivity - Frame

Table 3: Connectivity - Frame
Frame JointI JointJ Length
cm
1 1 2 600.
2 2 3 400.
3 3 4 400.
4 5 6 600.
5 6 7 400.
6 7 8 400.
7 9 10 400.
8 10 11 400.
9 7 11 400.
10 2 6 600.
11 3 7 600.
12 4 8 600.
13 6 10 400.

Table 4: Frame Section Assignments

Table 4: Frame Section Assignments
Frame AnalSect DesignSect MatProp

1 K 50/50 N.A. Default

2 K 50/50 N.A. Default
3 K 50/50 N.A. Default
4 K 50/50 N.A. Default
5 K 50/50 N.A. Default
6 K 50/50 N.A. Default
7 K 50/50 N.A. Default
8 K 50/50 N.A. Default
9 B 40/70 N.A. Default
10 B 40/70 N.A. Default
11 B 40/70 N.A. Default

YOSEP SUHUN Page 6 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

12 B 40/70 N.A. Default
13 B 40/70 N.A. Default

2. Material properties
This section provides material property information for materials used in the model.

Table 5: Material Properties 02 - Basic Mechanical Properties

Table 5: Material Properties 02 - Basic Mechanical Properties
Material UnitWeight UnitMass E1 G12 U12 A1
Kgf/cm3 Kgf-s2/cm4 Kgf/cm2 Kgf/cm2 1/C
4000Psi-1 2.4028E-03 2.4501E-06 253456.35 105606.81 0.2 9.9000E-06
A416Gr270 7.8490E-03 8.0038E-06 2003748.4 1.1700E-05
3
A615Gr60 7.8490E-03 8.0038E-06 2038901.9 1.1700E-05
2
A992Fy50 7.8490E-03 8.0038E-06 2038901.9 784193.04 0.3 1.1700E-05
2

Table 6: Material Properties 03a - Steel Data

Table 6: Material Properties 03a - Steel Data
Material Fy Fu FinalSlope
Kgf/cm2 Kgf/cm2
A992Fy50 3515.35 4569.95 -0.1

Table 7: Material Properties 03b - Concrete Data

Table 7: Material Properties 03b - Concrete Data
Material Fc eFc FinalSlope
Kgf/cm2 Kgf/cm2
4000Psi-1 281.23 281.23 -0.1

Table 8: Material Properties 03e - Rebar Data

Table 8: Material Properties 03e - Rebar Data
Material Fy Fu FinalSlope
Kgf/cm2 Kgf/cm2
A615Gr60 4218.42 6327.63 -0.1

Table 9: Material Properties 03f - Tendon Data

Table 9: Material Properties 03f - Tendon Data
Material Fy Fu FinalSlope
Kgf/cm2 Kgf/cm2
A416Gr270 17232.24 18982.88 -0.1

YOSEP SUHUN Page 7 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

3. Section properties
This section provides section property information for objects used in the model.

3.1. Frames

Table 10: Frame Section Properties 01 - General, Part 1 of 4

Table 10: Frame Section Properties 01 - General, Part 1 of 4
SectionName Material Shape t3 t2 tf tw t2b tfb
cm cm cm cm cm cm
B 40/70 4000Psi-1 Rectangular 70. 40.
FSEC1 A992Fy50 I/Wide Flange 30.48 12.7 0.9652 0.635 12.7 0.9652
K 50/50 4000Psi-1 Rectangular 50. 50.

Table 10: Frame Section Properties 01 - General, Part 2 of 4

Table 10: Frame Section Properties 01 - General, Part 2 of 4
SectionName Area TorsConst I33 I22 I23 AS2 AS3
cm2 cm4 cm4 cm4 cm4 cm2 cm2
B 40/70 2800. 960510.01 1143333.3 373333.33 0. 2333.33 2333.33
3
FSEC1 42.65 9.65 6572.42 330.13 0. 19.35 20.43
K 50/50 2500. 880208.33 520833.33 520833.33 0. 2083.33 2083.33

Table 10: Frame Section Properties 01 - General, Part 3 of 4

Table 10: Frame Section Properties 01 - General, Part 3 of 4
SectionName S33 S22 Z33 Z22 R33 R22
cm3 cm3 cm3 cm3 cm cm
B 40/70 32666.67 18666.67 49000. 28000. 20.2073 11.547
FSEC1 431.26 51.99 491.19 80.72 12.4145 2.7823
K 50/50 20833.33 20833.33 31250. 31250. 14.4338 14.4338

Table 10: Frame Section Properties 01 - General, Part 4 of 4

Table 10: Frame Section Properties 01 - General, Part 4 of 4
SectionName AMod A2Mod A3Mod JMod I2Mod I3Mod MMod WMod

B 40/70 1. 1. 1. 1. 1. 1. 1. 1.
FSEC1 1. 1. 1. 1. 1. 1. 1. 1.
K 50/50 1. 1. 1. 1. 1. 1. 1. 1.

Table 11: Frame Section Properties 02 - Concrete Column, Part 1 of 2

Table 11: Frame Section Properties 02 - Concrete Column, Part 1 of 2
SectionName RebarMatL RebarMatC ReinfConfig LatReinf Cover NumBars3D NumBars2D
ir ir
cm

YOSEP SUHUN Page 8 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

K 50/50 A615Gr60 A615Gr60 Rectangular Ties 4. 3 3

Table 11: Frame Section Properties 02 - Concrete Column, Part 2 of 2

Table 11: Frame Section Properties 02 - Concrete Column, Part 2 of 2
SectionName BarSizeL BarSizeC SpacingC NumCBars2 NumCBars3
cm
K 50/50 #9 #4 15. 3 3

Table 12: Frame Section Properties 03 - Concrete Beam, Part 1 of 2

Table 12: Frame Section Properties 03 - Concrete Beam, Part 1 of 2
SectionName RebarMatL RebarMatC TopCover BotCover
cm cm
B 40/70 A615Gr60 A615Gr60 6. 6.

Table 12: Frame Section Properties 03 - Concrete Beam, Part 2 of 2

Table 12: Frame Section Properties 03 - Concrete Beam, Part 2 of 2
SectionName TopLeftArea TopRghtAre BotLeftArea BotRghtAre
a a
cm2 cm2 cm2 cm2
B 40/70 0. 0. 0. 0.

3.2. Solids

Table 13: Solid Property Definitions

Table 13: Solid Property Definitions
SolidProp Material MatAngleA MatAngleB MatAngleC
Degrees Degrees Degrees
Solid1 4000Psi-1 0. 0. 0.

4. Load patterns
This section provides loading information as applied to the model.

4.1. Definitions

Table 14: Load Pattern Definitions

Table 14: Load Pattern Definitions
LoadPat DesignType SelfWtMult AutoLoad

BEBAN MATI Dead 1.

BEBAN HIDUP Live 1.
BEBAN ANGIN Wind 1. None

YOSEP SUHUN Page 9 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

5. Load cases
This section provides load case information.

5.1. Definitions

Table 15: Load Case Definitions, Part 1 of 2

Table 15: Load Case Definitions, Part 1 of 2
Case Type InitialCond ModalCase BaseCase MassSource DesActOpt

BEBAN MATI LinStatic Zero Prog Det

MODAL LinModal Zero Prog Det
BEBAN HIDUP LinStatic Zero Prog Det
BEBAN ANGIN LinStatic Zero Prog Det

Table 15: Load Case Definitions, Part 2 of 2

Table 15: Load Case
Definitions, Part 2 of 2
Case DesignAct

BEBAN MATI Non-

Composite
MODAL Other
BEBAN HIDUP Short-Term
Composite
BEBAN ANGIN Short-Term
Composite

5.2. Static case load assignments

Table 16: Case - Static 1 - Load Assignments

Table 16: Case - Static 1 - Load Assignments
Case LoadType LoadName LoadSF

BEBAN MATI Load pattern BEBAN MATI 1.

BEBAN HIDUP Load pattern BEBAN HIDUP 1.
BEBAN ANGIN Load pattern BEBAN ANGIN 1.

5.3. Response spectrum case load assignments

Table 17: Function - Response Spectrum - User

Table 17: Function - Response Spectrum - User

YOSEP SUHUN Page 10 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

Name Period Accel FuncDamp
Sec
UNIFRS 0. 1. 0.05
UNIFRS 1. 1.

6. Load combinations
This section provides load combination information.

Table 18: Combination Definitions

Table 18: Combination Definitions
ComboName ComboType CaseName ScaleFactor

COMB1 Linear Add BEBAN MATI 1.2

COMB1 BEBAN HIDUP 1.6
COMB2 Linear Add BEBAN MATI 1.2
COMB2 BEBAN HIDUP 0.5
COMB2 BEBAN ANGIN 1.3

YOSEP SUHUN Page 11 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

7. Structure results
This section provides structure results, including items such as structural periods and base reactions.

Figure 2: Deformed shape

7.1. Mass summary

Table 19: Assembled Joint Masses, Part 1 of 2

Table 19: Assembled Joint Masses, Part 1 of 2
Joint MassSource U1 U2 U3 R1 R2 R3 CenterX
Kgf-s2/cm Kgf-s2/cm Kgf-s2/cm Kgf-cm-s2 Kgf-cm-s2 Kgf-cm-s2 cm
1 MSSSRC1 1.84 1.84 1.84 0. 0. 0. 0.
2 MSSSRC1 5.12 5.12 5.12 0. 0. 0. 0.
3 MSSSRC1 4.51 4.51 4.51 0. 0. 0. 0.
4 MSSSRC1 3.28 3.28 3.28 0. 0. 0. 0.
5 MSSSRC1 1.84 1.84 1.84 0. 0. 0. 600.
6 MSSSRC1 6.49 6.49 6.49 0. 0. 0. 600.
7 MSSSRC1 5.88 5.88 5.88 0. 0. 0. 600.
8 MSSSRC1 3.28 3.28 3.28 0. 0. 0. 600.
9 MSSSRC1 1.23 1.23 1.23 0. 0. 0. 1000.
10 MSSSRC1 3.82 3.82 3.82 0. 0. 0. 1000.
11 MSSSRC1 2.6 2.6 2.6 0. 0. 0. 1000.
SumAccelUX MSSSRC1 39.89 0. 0. 0. 0. 0. 454.791
SumAccelUY MSSSRC1 0. 39.89 0. 0. 0. 0. 454.791
SumAccelUZ MSSSRC1 0. 0. 39.89 0. 0. 0. 454.791

YOSEP SUHUN Page 12 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

Table 19: Assembled Joint Masses, Part 2 of 2

Table 19: Assembled Joint Masses, Part 2 of 2
Joint MassSource CenterY CenterZ
cm cm
1 MSSSRC1 0. 0.
2 MSSSRC1 0. 600.
3 MSSSRC1 0. 1000.
4 MSSSRC1 0. 1400.
5 MSSSRC1 0. 0.
6 MSSSRC1 0. 600.
7 MSSSRC1 0. 1000.
8 MSSSRC1 0. 1400.
9 MSSSRC1 0. 200.
10 MSSSRC1 0. 600.
11 MSSSRC1 0. 1000.
SumAccelUX MSSSRC1 0. 794.349
SumAccelUY MSSSRC1 0. 794.349
SumAccelUZ MSSSRC1 0. 794.349

7.2. Modal results

Table 20: Modal Participating Mass Ratios

Table 20: Modal Participating Mass Ratios
OutputCase StepNum Period UX UY UZ SumUX SumUY SumUZ
Sec
MODAL 1. 0.98572 0. 0.72 0. 0. 0.72 0.
MODAL 2. 0.35603 0. 2.935E-02 0. 0. 0.75 0.
MODAL 3. 0.255885 0.94 0. 2.053E-05 0.94 0.75 2.053E-05
MODAL 4. 0.194552 0. 0.2 0. 0.94 0.95 2.053E-05
MODAL 5. 0.138538 0. 3.254E-03 0. 0.94 0.95 2.053E-05
MODAL 6. 0.113812 0. 2.314E-03 0. 0.94 0.95 2.053E-05
MODAL 7. 0.090865 5.219E-02 0. 2.066E-05 0.99 0.95 4.120E-05
MODAL 8. 0.072689 0. 3.478E-02 0. 0.99 0.99 4.120E-05
MODAL 9. 0.062952 0. 2.470E-03 0. 0.99 0.99 4.120E-05
MODAL 10. 0.056637 8.757E-03 0. 3.300E-04 1. 0.99 3.712E-04
MODAL 11. 0.055675 0. 1.064E-02 0. 1. 1. 3.712E-04
MODAL 12. 0.026578 7.032E-06 0. 0.66 1. 1. 0.66

7.3. Base reactions

Table 21: Base Reactions

Table 21: Base Reactions
OutputCase GlobalFX GlobalFY GlobalFZ GlobalMX GlobalMY GlobalMZ
Kgf Kgf Kgf Kgf-cm Kgf-cm Kgf-cm
BEBAN MATI -2.842E-14 0. 48117.09 0. -20490106.6 0.
BEBAN HIDUP 2.842E-14 0. 39131.09 0. -17801306.6 0.

YOSEP SUHUN Page 13 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

BEBAN ANGIN -6000. 0. 39117.09 0. -24590106.6 0.

8. Joint results
This section provides joint results, including items such as displacements and reactions.

Table 22: Joint Displacements

Table 22: Joint Displacements
Joint OutputCase U1 U2 U3 R1 R2 R3
cm cm cm Radians Radians Radians
1 BEBAN MATI 0. 0. 0. 0. 0. 0.
1 BEBAN HIDUP 0. 0. 0. 0. 0. 0.
1 BEBAN ANGIN 0. 0. 0. 0. 0. 0.
2 BEBAN MATI -0.002376 0. -0.01616 0. 0.000092 0.
2 BEBAN HIDUP -0.002911 0. -0.011946 0. 0.00005 0.
2 BEBAN ANGIN 0.21022 0. -0.008246 0. 0.000282 0.
3 BEBAN MATI -0.005098 0. -0.022867 0. 0.000059 0.
3 BEBAN HIDUP -0.00604 0. -0.016764 0. 0.000034 0.
3 BEBAN ANGIN 0.346251 0. -0.011476 0. 0.000244 0.
4 BEBAN MATI -0.00179 0. -0.025845 0. 0.00015 0.
4 BEBAN HIDUP -0.003232 0. -0.018796 0. 0.000089 0.
4 BEBAN ANGIN 0.469642 0. -0.012847 0. 0.000199 0.
5 BEBAN MATI 0. 0. 0. 0. 0. 0.
5 BEBAN HIDUP 0. 0. 0. 0. 0. 0.
5 BEBAN ANGIN 0. 0. 0. 0. 0. 0.
6 BEBAN MATI -0.001898 0. -0.019041 0. -0.000065 0.
6 BEBAN HIDUP -0.002621 0. -0.014659 0. -0.000033 0.
6 BEBAN ANGIN 0.209518 0. -0.01331 0. 0.000042 0.
7 BEBAN MATI -0.004987 0. -0.026612 0. -0.000043 0.
7 BEBAN HIDUP -0.006004 0. -0.020334 0. -0.00002 0.
7 BEBAN ANGIN 0.344479 0. -0.019388 0. 0.0001 0.
8 BEBAN MATI -0.002562 0. -0.029592 0. -0.000137 0.
8 BEBAN HIDUP -0.003667 0. -0.022367 0. -0.000077 0.
8 BEBAN ANGIN 0.467807 0. -0.022082 0. 0.000058 0.
9 BEBAN MATI 0. 0. 0. 0. 0. 0.
9 BEBAN HIDUP 0. 0. 0. 0. 0. 0.
9 BEBAN ANGIN 0. 0. 0. 0. 0. 0.
10 BEBAN MATI -0.001757 0. -0.003874 0. -0.000027 0.
10 BEBAN HIDUP -0.002495 0. -0.003931 0. -0.000029 0.
10 BEBAN ANGIN 0.208428 0. -0.007289 0. 0.000265 0.
11 BEBAN MATI -0.005178 0. -0.005489 0. -0.000061 0.
11 BEBAN HIDUP -0.006173 0. -0.005548 0. -0.000053 0.
11 BEBAN ANGIN 0.343494 0. -0.010085 0. 0.000041 0.

Table 23: Joint Reactions

Table 23: Joint Reactions
Joint OutputCase F1 F2 F3 M1 M2 M3
Kgf Kgf Kgf Kgf-cm Kgf-cm Kgf-cm
1 BEBAN MATI 215.71 0. 18868.3 0. 44452.08 0.
1 BEBAN HIDUP 129.82 0. 14418.35 0. 27838.64 0.
1 BEBAN ANGIN -903.2 0. 10510.8 0. -333004.74 0.

YOSEP SUHUN Page 14 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

5 BEBAN MATI -127.49 0. 21910.81 0. -23850.83 0.
5 BEBAN HIDUP -53.19 0. 17283.5 0. -8609.26 0.
5 BEBAN ANGIN -1414.83 0. 15857.96 0. -433793.7 0.
9 BEBAN MATI -88.22 0. 7337.98 0. -8598.51 0.
9 BEBAN HIDUP -76.63 0. 7429.24 0. -5870.22 0.
9 BEBAN ANGIN -3681.97 0. 12748.33 0. -823811.65 0.

9. Frame results
This section provides frame force results.

Table 24: Element Forces - Frames, Part 1 of 2

Table 24: Element Forces - Frames, Part 1 of 2
Frame Station OutputCase P V2 V3
cm Kgf Kgf Kgf
1 0. BEBAN MATI -18868.3 -215.71 0.
1 300. BEBAN MATI -17066.22 -215.71 0.
1 600. BEBAN MATI -15264.14 -215.71 0.
1 0. BEBAN HIDUP -14418.35 -129.82 0.
1 300. BEBAN HIDUP -12616.27 -129.82 0.
1 600. BEBAN HIDUP -10814.2 -129.82 0.
1 0. BEBAN ANGIN -10510.8 903.2 0.
1 300. BEBAN ANGIN -8708.73 903.2 0.
1 600. BEBAN ANGIN -6906.65 903.2 0.
2 0. BEBAN MATI -11825.05 -780.65 0.
2 200. BEBAN MATI -10623.66 -780.65 0.
2 400. BEBAN MATI -9422.28 -780.65 0.
2 0. BEBAN HIDUP -8833.26 -472.39 0.
2 200. BEBAN HIDUP -7631.87 -472.39 0.
2 400. BEBAN HIDUP -6430.49 -472.39 0.
2 0. BEBAN ANGIN -6317.88 732.54 0.
2 200. BEBAN ANGIN -5116.5 732.54 0.
2 400. BEBAN ANGIN -3915.11 732.54 0.
3 0. BEBAN MATI -5919.46 -912.63 0.
3 200. BEBAN MATI -4718.07 -912.63 0.
3 400. BEBAN MATI -3516.69 -912.63 0.
3 0. BEBAN HIDUP -4420.24 -514.88 0.
3 200. BEBAN HIDUP -3218.86 -514.88 0.
3 400. BEBAN HIDUP -2017.47 -514.88 0.
3 0. BEBAN ANGIN -3372.88 828.66 0.
3 200. BEBAN ANGIN -2171.5 828.66 0.
3 400. BEBAN ANGIN -970.11 828.66 0.
4 0. BEBAN MATI -21910.81 127.49 0.
4 300. BEBAN MATI -20108.74 127.49 0.
4 600. BEBAN MATI -18306.66 127.49 0.
4 0. BEBAN HIDUP -17283.5 53.19 0.
4 300. BEBAN HIDUP -15481.42 53.19 0.
4 600. BEBAN HIDUP -13679.35 53.19 0.
4 0. BEBAN ANGIN -15857.96 1414.83 0.
4 300. BEBAN ANGIN -14055.88 1414.83 0.
4 600. BEBAN ANGIN -12253.8 1414.83 0.
5 0. BEBAN MATI -13193.76 441.82 0.
5 200. BEBAN MATI -11992.38 441.82 0.
5 400. BEBAN MATI -10790.99 441.82 0.

YOSEP SUHUN Page 15 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

5 0. BEBAN HIDUP -10190.63 172.59 0.
5 200. BEBAN HIDUP -8989.24 172.59 0.
5 400. BEBAN HIDUP -7787.86 172.59 0.
5 0. BEBAN ANGIN -10830.27 2519.56 0.
5 200. BEBAN ANGIN -9628.89 2519.56 0.
5 400. BEBAN ANGIN -8427.5 2519.56 0.
6 0. BEBAN MATI -5922.73 912.63 0.
6 200. BEBAN MATI -4721.35 912.63 0.
6 400. BEBAN MATI -3519.96 912.63 0.
6 0. BEBAN HIDUP -4421.95 514.88 0.
6 200. BEBAN HIDUP -3220.56 514.88 0.
6 400. BEBAN HIDUP -2019.18 514.88 0.
6 0. BEBAN ANGIN -5469.31 2171.34 0.
6 200. BEBAN ANGIN -4267.92 2171.34 0.
6 400. BEBAN ANGIN -3066.54 2171.34 0.
7 0. BEBAN MATI -7337.98 88.22 0.
7 200. BEBAN MATI -6136.59 88.22 0.
7 400. BEBAN MATI -4935.21 88.22 0.
7 0. BEBAN HIDUP -7429.24 76.63 0.
7 200. BEBAN HIDUP -6227.85 76.63 0.
7 400. BEBAN HIDUP -5026.47 76.63 0.
7 0. BEBAN ANGIN -12748.33 3681.97 0.
7 200. BEBAN ANGIN -11546.95 3681.97 0.
7 400. BEBAN ANGIN -10345.56 3681.97 0.
8 0. BEBAN MATI -3759.44 338.83 0.
8 200. BEBAN MATI -2558.06 338.83 0.
8 400. BEBAN MATI -1356.67 338.83 0.
8 0. BEBAN HIDUP -3761.37 299.8 0.
8 200. BEBAN HIDUP -2559.99 299.8 0.
8 400. BEBAN HIDUP -1358.6 299.8 0.
8 0. BEBAN ANGIN -5630.1 1747.9 0.
8 200. BEBAN ANGIN -4428.71 1747.9 0.
8 400. BEBAN ANGIN -3227.33 1747.9 0.
9 0. BEBAN MATI -338.83 -1334.43 0.
9 50. BEBAN MATI -338.83 -998.04 0.
9 100. BEBAN MATI -338.83 -661.65 0.
9 150. BEBAN MATI -338.83 -325.26 0.
9 200. BEBAN MATI -338.83 11.12 0.
9 200. BEBAN MATI -338.83 11.12 0.
9 250. BEBAN MATI -338.83 347.51 0.
9 300. BEBAN MATI -338.83 683.9 0.
9 350. BEBAN MATI -338.83 1020.29 0.
9 400. BEBAN MATI -338.83 1356.67 0.
9 0. BEBAN HIDUP -299.8 -1339.5 0.
9 50. BEBAN HIDUP -299.8 -1003.11 0.
9 100. BEBAN HIDUP -299.8 -666.73 0.
9 150. BEBAN HIDUP -299.8 -330.34 0.
9 200. BEBAN HIDUP -299.8 6.05 0.
9 200. BEBAN HIDUP -299.8 13.05 0.
9 250. BEBAN HIDUP -299.8 349.44 0.
9 300. BEBAN HIDUP -299.8 685.83 0.
9 350. BEBAN HIDUP -299.8 1022.21 0.
9 400. BEBAN HIDUP -299.8 1358.6 0.
9 0. BEBAN ANGIN -1747.9 536.23 0.
9 50. BEBAN ANGIN -1747.9 872.62 0.
9 100. BEBAN ANGIN -1747.9 1209. 0.
9 150. BEBAN ANGIN -1747.9 1545.39 0.

YOSEP SUHUN Page 16 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

9 200. BEBAN ANGIN -1747.9 1881.78 0.
9 200. BEBAN ANGIN -1747.9 1881.78 0.
9 250. BEBAN ANGIN -1747.9 2218.17 0.
9 300. BEBAN ANGIN -1747.9 2554.55 0.
9 350. BEBAN ANGIN -1747.9 2890.94 0.
9 400. BEBAN ANGIN -1747.9 3227.33 0.
10 0. BEBAN MATI 564.94 -3439.09 0.
10 50. BEBAN MATI 564.94 -2852.71 0.
10 100. BEBAN MATI 564.94 -2266.32 0.
10 150. BEBAN MATI 564.94 -1679.93 0.
10 200. BEBAN MATI 564.94 -1093.54 0.
10 250. BEBAN MATI 564.94 -507.16 0.
10 300. BEBAN MATI 564.94 79.23 0.
10 350. BEBAN MATI 564.94 665.62 0.
10 400. BEBAN MATI 564.94 1252.01 0.
10 450. BEBAN MATI 564.94 1838.4 0.
10 500. BEBAN MATI 564.94 2424.78 0.
10 550. BEBAN MATI 564.94 3011.17 0.
10 600. BEBAN MATI 564.94 3597.56 0.
10 0. BEBAN HIDUP 342.57 -1980.94 0.
10 50. BEBAN HIDUP 342.57 -1644.55 0.
10 100. BEBAN HIDUP 342.57 -1308.16 0.
10 150. BEBAN HIDUP 342.57 -971.78 0.
10 200. BEBAN HIDUP 342.57 -635.39 0.
10 250. BEBAN HIDUP 342.57 -299. 0.
10 300. BEBAN HIDUP 342.57 37.39 0.
10 350. BEBAN HIDUP 342.57 373.78 0.
10 400. BEBAN HIDUP 342.57 710.16 0.
10 450. BEBAN HIDUP 342.57 1046.55 0.
10 500. BEBAN HIDUP 342.57 1382.94 0.
10 550. BEBAN HIDUP 342.57 1719.33 0.
10 600. BEBAN HIDUP 342.57 2055.71 0.
10 0. BEBAN ANGIN -829.34 -588.77 0.
10 50. BEBAN ANGIN -829.34 -252.38 0.
10 100. BEBAN ANGIN -829.34 84.01 0.
10 150. BEBAN ANGIN -829.34 420.4 0.
10 200. BEBAN ANGIN -829.34 756.78 0.
10 250. BEBAN ANGIN -829.34 1093.17 0.
10 300. BEBAN ANGIN -829.34 1429.56 0.
10 350. BEBAN ANGIN -829.34 1765.95 0.
10 400. BEBAN ANGIN -829.34 2102.33 0.
10 450. BEBAN ANGIN -829.34 2438.72 0.
10 500. BEBAN ANGIN -829.34 2775.11 0.
10 550. BEBAN ANGIN -829.34 3111.5 0.
10 600. BEBAN ANGIN -829.34 3447.89 0.
11 0. BEBAN MATI 131.98 -3502.82 0.
11 50. BEBAN MATI 131.98 -2916.43 0.
11 100. BEBAN MATI 131.98 -2330.05 0.
11 150. BEBAN MATI 131.98 -1743.66 0.
11 200. BEBAN MATI 131.98 -1157.27 0.
11 250. BEBAN MATI 131.98 -570.88 0.
11 300. BEBAN MATI 131.98 15.51 0.
11 350. BEBAN MATI 131.98 601.89 0.
11 400. BEBAN MATI 131.98 1188.28 0.
11 450. BEBAN MATI 131.98 1774.67 0.
11 500. BEBAN MATI 131.98 2361.06 0.
11 550. BEBAN MATI 131.98 2947.44 0.

YOSEP SUHUN Page 17 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

11 600. BEBAN MATI 131.98 3533.83 0.
11 0. BEBAN HIDUP 42.49 -2010.24 0.
11 50. BEBAN HIDUP 42.49 -1673.86 0.
11 100. BEBAN HIDUP 42.49 -1337.47 0.
11 150. BEBAN HIDUP 42.49 -1001.08 0.
11 200. BEBAN HIDUP 42.49 -664.69 0.
11 250. BEBAN HIDUP 42.49 -328.31 0.
11 300. BEBAN HIDUP 42.49 8.08 0.
11 350. BEBAN HIDUP 42.49 344.47 0.
11 400. BEBAN HIDUP 42.49 680.86 0.
11 450. BEBAN HIDUP 42.49 1017.25 0.
11 500. BEBAN HIDUP 42.49 1353.63 0.
11 550. BEBAN HIDUP 42.49 1690.02 0.
11 600. BEBAN HIDUP 42.49 2026.41 0.
11 0. BEBAN ANGIN -2096.12 -542.23 0.
11 50. BEBAN ANGIN -2096.12 -205.84 0.
11 100. BEBAN ANGIN -2096.12 130.55 0.
11 150. BEBAN ANGIN -2096.12 466.93 0.
11 200. BEBAN ANGIN -2096.12 803.32 0.
11 250. BEBAN ANGIN -2096.12 1139.71 0.
11 300. BEBAN ANGIN -2096.12 1476.1 0.
11 350. BEBAN ANGIN -2096.12 1812.48 0.
11 400. BEBAN ANGIN -2096.12 2148.87 0.
11 450. BEBAN ANGIN -2096.12 2485.26 0.
11 500. BEBAN ANGIN -2096.12 2821.65 0.
11 550. BEBAN ANGIN -2096.12 3158.04 0.
11 600. BEBAN ANGIN -2096.12 3494.42 0.
12 0. BEBAN MATI -912.63 -3516.69 0.
12 50. BEBAN MATI -912.63 -2930.3 0.
12 100. BEBAN MATI -912.63 -2343.91 0.
12 150. BEBAN MATI -912.63 -1757.53 0.
12 200. BEBAN MATI -912.63 -1171.14 0.
12 250. BEBAN MATI -912.63 -584.75 0.
12 300. BEBAN MATI -912.63 1.64 0.
12 350. BEBAN MATI -912.63 588.03 0.
12 400. BEBAN MATI -912.63 1174.41 0.
12 450. BEBAN MATI -912.63 1760.8 0.
12 500. BEBAN MATI -912.63 2347.19 0.
12 550. BEBAN MATI -912.63 2933.58 0.
12 600. BEBAN MATI -912.63 3519.96 0.
12 0. BEBAN HIDUP -514.88 -2017.47 0.
12 50. BEBAN HIDUP -514.88 -1681.09 0.
12 100. BEBAN HIDUP -514.88 -1344.7 0.
12 150. BEBAN HIDUP -514.88 -1008.31 0.
12 200. BEBAN HIDUP -514.88 -671.92 0.
12 250. BEBAN HIDUP -514.88 -335.53 0.
12 300. BEBAN HIDUP -514.88 0.85 0.
12 350. BEBAN HIDUP -514.88 337.24 0.
12 400. BEBAN HIDUP -514.88 673.63 0.
12 450. BEBAN HIDUP -514.88 1010.02 0.
12 500. BEBAN HIDUP -514.88 1346.4 0.
12 550. BEBAN HIDUP -514.88 1682.79 0.
12 600. BEBAN HIDUP -514.88 2019.18 0.
12 0. BEBAN ANGIN -2171.34 -970.11 0.
12 50. BEBAN ANGIN -2171.34 -633.73 0.
12 100. BEBAN ANGIN -2171.34 -297.34 0.
12 150. BEBAN ANGIN -2171.34 39.05 0.

YOSEP SUHUN Page 18 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

12 200. BEBAN ANGIN -2171.34 375.44 0.
12 250. BEBAN ANGIN -2171.34 711.83 0.
12 300. BEBAN ANGIN -2171.34 1048.21 0.
12 350. BEBAN ANGIN -2171.34 1384.6 0.
12 400. BEBAN ANGIN -2171.34 1720.99 0.
12 450. BEBAN ANGIN -2171.34 2057.38 0.
12 500. BEBAN ANGIN -2171.34 2393.76 0.
12 550. BEBAN ANGIN -2171.34 2730.15 0.
12 600. BEBAN ANGIN -2171.34 3066.54 0.
13 0. BEBAN MATI 250.61 -1515.34 0.
13 50. BEBAN MATI 250.61 -1178.95 0.
13 100. BEBAN MATI 250.61 -842.56 0.
13 150. BEBAN MATI 250.61 -506.18 0.
13 200. BEBAN MATI 250.61 -169.79 0.
13 200. BEBAN MATI 250.61 -169.79 0.
13 250. BEBAN MATI 250.61 166.6 0.
13 300. BEBAN MATI 250.61 502.99 0.
13 350. BEBAN MATI 250.61 839.38 0.
13 400. BEBAN MATI 250.61 1175.76 0.
13 0. BEBAN HIDUP 223.17 -1433. 0.
13 50. BEBAN HIDUP 223.17 -1096.62 0.
13 100. BEBAN HIDUP 223.17 -760.23 0.
13 150. BEBAN HIDUP 223.17 -423.84 0.
13 200. BEBAN HIDUP 223.17 -87.45 0.
13 200. BEBAN HIDUP 223.17 -80.45 0.
13 250. BEBAN HIDUP 223.17 255.94 0.
13 300. BEBAN HIDUP 223.17 592.32 0.
13 350. BEBAN HIDUP 223.17 928.71 0.
13 400. BEBAN HIDUP 223.17 1265.1 0.
13 0. BEBAN ANGIN -1934.06 2024.36 0.
13 50. BEBAN ANGIN -1934.06 2360.75 0.
13 100. BEBAN ANGIN -1934.06 2697.13 0.
13 150. BEBAN ANGIN -1934.06 3033.52 0.
13 200. BEBAN ANGIN -1934.06 3369.91 0.
13 200. BEBAN ANGIN -1934.06 3369.91 0.
13 250. BEBAN ANGIN -1934.06 3706.3 0.
13 300. BEBAN ANGIN -1934.06 4042.69 0.
13 350. BEBAN ANGIN -1934.06 4379.07 0.
13 400. BEBAN ANGIN -1934.06 4715.46 0.

Table 24: Element Forces - Frames, Part 2 of 2

Table 24: Element Forces - Frames, Part 2 of 2
Frame Station OutputCase T M2 M3
cm Kgf-cm Kgf-cm Kgf-cm
1 0. BEBAN MATI 0. 0. -44452.08
1 300. BEBAN MATI 0. 0. 20259.65
1 600. BEBAN MATI 0. 0. 84971.37
1 0. BEBAN HIDUP 0. 0. -27838.64
1 300. BEBAN HIDUP 0. 0. 11106.98
1 600. BEBAN HIDUP 0. 0. 50052.61
1 0. BEBAN ANGIN 0. 0. 333004.74
1 300. BEBAN ANGIN 0. 0. 62044.42
1 600. BEBAN ANGIN 0. 0. -208915.9
2 0. BEBAN MATI 0. 0. -167015.62
2 200. BEBAN MATI 0. 0. -10886.35
2 400. BEBAN MATI 0. 0. 145242.93

YOSEP SUHUN Page 19 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

2 0. BEBAN HIDUP 0. 0. -100052.77
2 200. BEBAN HIDUP 0. 0. -5574.67
2 400. BEBAN HIDUP 0. 0. 88903.43
2 0. BEBAN ANGIN 0. 0. 133807.81
2 200. BEBAN ANGIN 0. 0. -12700.74
2 400. BEBAN ANGIN 0. 0. -159209.3
3 0. BEBAN MATI 0. 0. -152494.28
3 200. BEBAN MATI 0. 0. 30031.96
3 400. BEBAN MATI 0. 0. 212558.2
3 0. BEBAN HIDUP 0. 0. -84644.28
3 200. BEBAN HIDUP 0. 0. 18332.42
3 400. BEBAN HIDUP 0. 0. 121309.11
3 0. BEBAN ANGIN 0. 0. 150879.25
3 200. BEBAN ANGIN 0. 0. -14852.93
3 400. BEBAN ANGIN 0. 0. -180585.11
4 0. BEBAN MATI 0. 0. 23850.83
4 300. BEBAN MATI 0. 0. -14395.96
4 600. BEBAN MATI 0. 0. -52642.76
4 0. BEBAN HIDUP 0. 0. 8609.26
4 300. BEBAN HIDUP 0. 0. -7347.38
4 600. BEBAN HIDUP 0. 0. -23304.02
4 0. BEBAN ANGIN 0. 0. 433793.7
4 300. BEBAN ANGIN 0. 0. 9343.71
4 600. BEBAN ANGIN 0. 0. -415106.29
5 0. BEBAN MATI 0. 0. 95674.75
5 200. BEBAN MATI 0. 0. 7311.62
5 400. BEBAN MATI 0. 0. -81051.51
5 0. BEBAN HIDUP 0. 0. 38953.76
5 200. BEBAN HIDUP 0. 0. 4436.35
5 400. BEBAN HIDUP 0. 0. -30081.07
5 0. BEBAN ANGIN 0. 0. 523049.98
5 200. BEBAN ANGIN 0. 0. 19138.93
5 400. BEBAN ANGIN 0. 0. -484772.13
6 0. BEBAN MATI 0. 0. 151511.81
6 200. BEBAN MATI 0. 0. -31014.42
6 400. BEBAN MATI 0. 0. -213540.66
6 0. BEBAN HIDUP 0. 0. 84132.15
6 200. BEBAN HIDUP 0. 0. -18844.55
6 400. BEBAN HIDUP 0. 0. -121821.24
6 0. BEBAN ANGIN 0. 0. 420192.84
6 200. BEBAN ANGIN 0. 0. -14074.98
6 400. BEBAN ANGIN 0. 0. -448342.8
7 0. BEBAN MATI 0. 0. 8598.51
7 200. BEBAN MATI 0. 0. -9044.78
7 400. BEBAN MATI 0. 0. -26688.06
7 0. BEBAN HIDUP 0. 0. 5870.22
7 200. BEBAN HIDUP 0. 0. -9455.76
7 400. BEBAN HIDUP 0. 0. -24781.75
7 0. BEBAN ANGIN 0. 0. 823811.65
7 200. BEBAN ANGIN 0. 0. 87418.53
7 400. BEBAN ANGIN 0. 0. -648974.6
8 0. BEBAN MATI 0. 0. 56605.82
8 200. BEBAN MATI 0. 0. -11160.32
8 400. BEBAN MATI 0. 0. -78926.46
8 0. BEBAN HIDUP 0. 0. 51917.27
8 200. BEBAN HIDUP 0. 0. -8043.41
8 400. BEBAN HIDUP 0. 0. -68004.09

YOSEP SUHUN Page 20 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

8 0. BEBAN ANGIN 0. 0. 275845.04
8 200. BEBAN ANGIN 0. 0. -73735.34
8 400. BEBAN ANGIN 0. 0. -423315.73
9 0. BEBAN MATI 0. 0. -74477.01
9 50. BEBAN MATI 0. 0. -16165.34
9 100. BEBAN MATI 0. 0. 25326.95
9 150. BEBAN MATI 0. 0. 49999.85
9 200. BEBAN MATI 0. 0. 57853.37
9 200. BEBAN MATI 0. 0. 57853.37
9 250. BEBAN MATI 0. 0. 48887.49
9 300. BEBAN MATI 0. 0. 23102.23
9 350. BEBAN MATI 0. 0. -19502.42
9 400. BEBAN MATI 0. 0. -78926.46
9 0. BEBAN HIDUP 0. 0. -64183.92
9 50. BEBAN HIDUP 0. 0. -5618.58
9 100. BEBAN HIDUP 0. 0. 36127.36
9 150. BEBAN HIDUP 0. 0. 61053.92
9 200. BEBAN HIDUP 0. 0. 69161.1
9 200. BEBAN HIDUP 0. 0. 69161.1
9 250. BEBAN HIDUP 0. 0. 60098.88
9 300. BEBAN HIDUP 0. 0. 34217.28
9 350. BEBAN HIDUP 0. 0. -8483.72
9 400. BEBAN HIDUP 0. 0. -68004.09
9 0. BEBAN ANGIN 0. 0. 329395.74
9 50. BEBAN ANGIN 0. 0. 294174.66
9 100. BEBAN ANGIN 0. 0. 242134.2
9 150. BEBAN ANGIN 0. 0. 173274.35
9 200. BEBAN ANGIN 0. 0. 87595.11
9 200. BEBAN ANGIN 0. 0. 87595.11
9 250. BEBAN ANGIN 0. 0. -14903.52
9 300. BEBAN ANGIN 0. 0. -134221.54
9 350. BEBAN ANGIN 0. 0. -270358.94
9 400. BEBAN ANGIN 0. 0. -423315.73
10 0. BEBAN MATI 0. 0. -251986.99
10 50. BEBAN MATI 0. 0. -94691.97
10 100. BEBAN MATI 0. 0. 33283.66
10 150. BEBAN MATI 0. 0. 131939.91
10 200. BEBAN MATI 0. 0. 201276.77
10 250. BEBAN MATI 0. 0. 241294.24
10 300. BEBAN MATI 0. 0. 251992.33
10 350. BEBAN MATI 0. 0. 233371.02
10 400. BEBAN MATI 0. 0. 185430.33
10 450. BEBAN MATI 0. 0. 108170.25
10 500. BEBAN MATI 0. 0. 1590.78
10 550. BEBAN MATI 0. 0. -134308.07
10 600. BEBAN MATI 0. 0. -299526.31
10 0. BEBAN HIDUP 0. 0. -150105.37
10 50. BEBAN HIDUP 0. 0. -59468.12
10 100. BEBAN HIDUP 0. 0. 14349.75
10 150. BEBAN HIDUP 0. 0. 71348.23
10 200. BEBAN HIDUP 0. 0. 111527.32
10 250. BEBAN HIDUP 0. 0. 134887.03
10 300. BEBAN HIDUP 0. 0. 141427.34
10 350. BEBAN HIDUP 0. 0. 131148.27
10 400. BEBAN HIDUP 0. 0. 104049.82
10 450. BEBAN HIDUP 0. 0. 60131.97
10 500. BEBAN HIDUP 0. 0. -605.26

YOSEP SUHUN Page 21 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

10 550. BEBAN HIDUP 0. 0. -78161.88
10 600. BEBAN HIDUP 0. 0. -172537.89
10 0. BEBAN ANGIN 0. 0. 342723.71
10 50. BEBAN ANGIN 0. 0. 363752.38
10 100. BEBAN ANGIN 0. 0. 367961.67
10 150. BEBAN ANGIN 0. 0. 355351.57
10 200. BEBAN ANGIN 0. 0. 325922.08
10 250. BEBAN ANGIN 0. 0. 279673.2
10 300. BEBAN ANGIN 0. 0. 216604.93
10 350. BEBAN ANGIN 0. 0. 136717.28
10 400. BEBAN ANGIN 0. 0. 40010.24
10 450. BEBAN ANGIN 0. 0. -73516.19
10 500. BEBAN ANGIN 0. 0. -203862.01
10 550. BEBAN ANGIN 0. 0. -351027.21
10 600. BEBAN ANGIN 0. 0. -515011.8
11 0. BEBAN MATI 0. 0. -297737.21
11 50. BEBAN MATI 0. 0. -137255.84
11 100. BEBAN MATI 0. 0. -6093.85
11 150. BEBAN MATI 0. 0. 95748.74
11 200. BEBAN MATI 0. 0. 168271.95
11 250. BEBAN MATI 0. 0. 211475.77
11 300. BEBAN MATI 0. 0. 225360.2
11 350. BEBAN MATI 0. 0. 209925.25
11 400. BEBAN MATI 0. 0. 165170.91
11 450. BEBAN MATI 0. 0. 91097.18
11 500. BEBAN MATI 0. 0. -12295.94
11 550. BEBAN MATI 0. 0. -145008.45
11 600. BEBAN MATI 0. 0. -307040.34
11 0. BEBAN HIDUP 0. 0. -173547.71
11 50. BEBAN HIDUP 0. 0. -81445.19
11 100. BEBAN HIDUP 0. 0. -6162.07
11 150. BEBAN HIDUP 0. 0. 52301.67
11 200. BEBAN HIDUP 0. 0. 93946.02
11 250. BEBAN HIDUP 0. 0. 118770.98
11 300. BEBAN HIDUP 0. 0. 126776.56
11 350. BEBAN HIDUP 0. 0. 117962.74
11 400. BEBAN HIDUP 0. 0. 92329.54
11 450. BEBAN HIDUP 0. 0. 49876.95
11 500. BEBAN HIDUP 0. 0. -9395.02
11 550. BEBAN HIDUP 0. 0. -85486.38
11 600. BEBAN HIDUP 0. 0. -178397.14
11 0. BEBAN ANGIN 0. 0. 310088.55
11 50. BEBAN ANGIN 0. 0. 328790.37
11 100. BEBAN ANGIN 0. 0. 330672.8
11 150. BEBAN ANGIN 0. 0. 315735.84
11 200. BEBAN ANGIN 0. 0. 283979.49
11 250. BEBAN ANGIN 0. 0. 235403.76
11 300. BEBAN ANGIN 0. 0. 170008.64
11 350. BEBAN ANGIN 0. 0. 87794.13
11 400. BEBAN ANGIN 0. 0. -11239.77
11 450. BEBAN ANGIN 0. 0. -127093.05
11 500. BEBAN ANGIN 0. 0. -259765.72
11 550. BEBAN ANGIN 0. 0. -409257.78
11 600. BEBAN ANGIN 0. 0. -575569.23
12 0. BEBAN MATI 0. 0. -212558.2
12 50. BEBAN MATI 0. 0. -51383.44
12 100. BEBAN MATI 0. 0. 80471.94

YOSEP SUHUN Page 22 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

12 150. BEBAN MATI 0. 0. 183007.92
12 200. BEBAN MATI 0. 0. 256224.52
12 250. BEBAN MATI 0. 0. 300121.73
12 300. BEBAN MATI 0. 0. 314699.55
12 350. BEBAN MATI 0. 0. 299957.98
12 400. BEBAN MATI 0. 0. 255897.03
12 450. BEBAN MATI 0. 0. 182516.69
12 500. BEBAN MATI 0. 0. 79816.96
12 550. BEBAN MATI 0. 0. -52202.16
12 600. BEBAN MATI 0. 0. -213540.66
12 0. BEBAN HIDUP 0. 0. -121309.11
12 50. BEBAN HIDUP 0. 0. -28845.16
12 100. BEBAN HIDUP 0. 0. 46799.41
12 150. BEBAN HIDUP 0. 0. 105624.59
12 200. BEBAN HIDUP 0. 0. 147630.38
12 250. BEBAN HIDUP 0. 0. 172816.79
12 300. BEBAN HIDUP 0. 0. 181183.8
12 350. BEBAN HIDUP 0. 0. 172731.43
12 400. BEBAN HIDUP 0. 0. 147459.67
12 450. BEBAN HIDUP 0. 0. 105368.52
12 500. BEBAN HIDUP 0. 0. 46457.99
12 550. BEBAN HIDUP 0. 0. -29271.93
12 600. BEBAN HIDUP 0. 0. -121821.24
12 0. BEBAN ANGIN 0. 0. 180585.11
12 50. BEBAN ANGIN 0. 0. 220681.08
12 100. BEBAN ANGIN 0. 0. 243957.67
12 150. BEBAN ANGIN 0. 0. 250414.87
12 200. BEBAN ANGIN 0. 0. 240052.68
12 250. BEBAN ANGIN 0. 0. 212871.1
12 300. BEBAN ANGIN 0. 0. 168870.13
12 350. BEBAN ANGIN 0. 0. 108049.78
12 400. BEBAN ANGIN 0. 0. 30410.04
12 450. BEBAN ANGIN 0. 0. -64049.09
12 500. BEBAN ANGIN 0. 0. -175327.6
12 550. BEBAN ANGIN 0. 0. -303425.5
12 600. BEBAN ANGIN 0. 0. -448342.8
13 0. BEBAN MATI 0. 0. -151208.8
13 50. BEBAN MATI 0. 0. -83851.57
13 100. BEBAN MATI 0. 0. -33313.74
13 150. BEBAN MATI 0. 0. 404.7
13 200. BEBAN MATI 0. 0. 17303.76
13 200. BEBAN MATI 0. 0. 17303.76
13 250. BEBAN MATI 0. 0. 17383.43
13 300. BEBAN MATI 0. 0. 643.72
13 350. BEBAN MATI 0. 0. -32915.39
13 400. BEBAN MATI 0. 0. -83293.88
13 0. BEBAN HIDUP 0. 0. -110280.11
13 50. BEBAN HIDUP 0. 0. -47039.62
13 100. BEBAN HIDUP 0. 0. -618.51
13 150. BEBAN HIDUP 0. 0. 28983.21
13 200. BEBAN HIDUP 0. 0. 41765.53
13 200. BEBAN HIDUP 0. 0. 41765.53
13 250. BEBAN HIDUP 0. 0. 37378.48
13 300. BEBAN HIDUP 0. 0. 16172.03
13 350. BEBAN HIDUP 0. 0. -21853.8
13 400. BEBAN HIDUP 0. 0. -76699.02
13 0. BEBAN ANGIN 0. 0. 423144.47

YOSEP SUHUN Page 23 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

13 50. BEBAN ANGIN 0. 0. 313516.81
13 100. BEBAN ANGIN 0. 0. 187069.77
13 150. BEBAN ANGIN 0. 0. 43803.34
13 200. BEBAN ANGIN 0. 0. -116282.48
13 200. BEBAN ANGIN 0. 0. -116282.48
13 250. BEBAN ANGIN 0. 0. -293187.69
13 300. BEBAN ANGIN 0. 0. -486912.29
13 350. BEBAN ANGIN 0. 0. -697456.27
13 400. BEBAN ANGIN 0. 0. -924819.64

10. Material take-off

This section provides a material take-off.

Table 25: Material List 2 - By Section Property

Table 25: Material List 2 - By Section Property
Section ObjectType NumPieces TotalLength TotalWeight
cm Kgf
K 50/50 Frame 8 3600. 21624.93
B 40/70 Frame 5 2600. 17492.16

11. Design preferences

This section provides the design preferences for each type of design, which typically include material reduction
factors, framing type, stress ratio limit, deflection limits, and other code specific items.

11.1. Steel design

Table 26: Preferences - Steel Design - AISC 360-10, Part 1 of 4

Table 26: Preferences - Steel Design - AISC 360-10, Part 1 of 4
THDesign FrameType PatLLF SRatioLimit MaxIter SDC SeisCode SeisLoad ImpFactor

Envelopes SMF 0.75 0.95 1 D Yes Yes 1.

Table 26: Preferences - Steel Design - AISC 360-10, Part 2 of 4

Table 26: Preferences - Steel Design - AISC 360-10, Part 2 of 4
SystemRho SystemSds SystemR SystemCd Omega0 Provision AMethod SOMethod SRMethod

1. 0.5 8. 5.5 3. LRFD Direct General 2nd Tau-b Fixed

Analysis Order

Table 26: Preferences - Steel Design - AISC 360-10, Part 3 of 4

Table 26: Preferences - Steel Design - AISC 360-10, Part 3 of 4
NLCoeff PhiB PhiC PhiTY PhiTF PhiV PhiVRolledI PhiVT PlugWeld

YOSEP SUHUN Page 24 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

0.002 0.9 0.9 0.9 0.75 0.9 1. 0.9 Yes

Table 26: Preferences - Steel Design - AISC 360-10, Part 4 of 4

Table 26: Preferences - Steel Design - AISC 360-10, Part 4 of 4
HSSWelding HSSReduce CheckDefl DLRat SDLAndLLR LLRat TotalRat NetRat
T at

ERW No No 120. 120. 360. 240. 240.

11.2. Concrete design

Table 27: Preferences - Concrete Design - ACI 318-14, Part 1 of 2

Table 27: Preferences - Concrete Design - ACI 318-14, Part 1 of 2
THDesign NumCurves NumPoints MinEccen PatLLF UFLimit SeisCat Rho Sds

Envelopes 24 11 Yes 0.75 0.95 D 1. 0.5

Table 27: Preferences - Concrete Design - ACI 318-14, Part 2 of 2

Table 27: Preferences - Concrete Design - ACI 318-14, Part 2 of 2
PhiT PhiCTied PhiCSpiral PhiV PhiVSeismi PhiVJoint
c

0.9 0.65 0.75 0.75 0.6 0.85

11.3. Aluminum design

Table 28: Preferences - Aluminum Design - AA-ASD 2000

Table 28: Preferences - Aluminum Design - AA-ASD 2000
FrameType SRatioLimit LatFact UseLatFact

Moment Frame 1. 1.333333 No

11.4. Cold formed design

Table 29: Preferences - Cold Formed Design - AISI-ASD96

Table 29: Preferences - Cold Formed Design - AISI-ASD96
FrameType SRatioLim OmegaBS OmegaBU OmegaBL OmegaVS OmegaVN OmegaT OmegaC
it S TB S

Braced Frame 1. 1.67 1.67 1.67 1.67 1.5 1.67 1.8

YOSEP SUHUN Page 25 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

GAMBAR BIDANG M

KOMBINASI 1

YOSEP SUHUN Page 26 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

KOMBINASI 2

GAMBAR BIDANG D

YOSEP SUHUN Page 27 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

KOMBINASI 1

KOMBINASI 2

GAMBAR BIDANG N

YOSEP SUHUN Page 28 of 29

TUGAS YOSEP.sdb SAP2000 v19.2.1 - License #3010*1PGKAJSQP7BM4DY

Contents 06 November 2018

KOMBINASI 1

KOMBINASI 2

YOSEP SUHUN Page 29 of 29