Superposition Theorem

Topic :- Superposition Theorem
Superposition Theorem
• The superposition theorem extends the use of Ohm’s Law to
circuits with multiple sources.
• Definition :- The current through, or voltage across, an
element in a linear bilateral network equal to the
algebraic sum of the currents or voltages produced
independently by each source.
• The Superposition theorem is very helpful in determining the
voltage across an element or current through a branch when
the circuit contains multiple number of voltage or current
sources.
Superposition Theorem
 In order to apply the superposition theorem to a network, certain
conditions must be met :
1. All the components must be linear, for e.g.- the current is
proportional to the applied voltage (for resistors), flux linkage is
proportional to current (in inductors), etc.
2. All the components must be bilateral, meaning that the current is the
same amount for opposite polarities of the source voltage.
3. Passive components may be used. These are components such as
resistors, capacitors, and inductors, that do not amplify or rectify.
4. Active components may not be used. Active components include
transistors, semiconductor diodes, and electron tubes. Such
components are never bilateral and seldom linear.
Procedure for applying Superposition Theorem
 Circuits Containing Only Independent Sources
• Consider only one source to be active at a time.
• Remove all other IDEAL VOLTAGE SOURCES by SHORT CIRCUIT & all
other IDEAL CURRENT SOURCES by OPEN CIRCUIT.
Voltage source
Current source is
is replaced by a
replaced by a
Short Circuit
Open Circuit
• If there are practical sources, replace them by the
combination of ideal source and an internal resistances (as
shown in figure).
• After that, short circuit the ideal voltage source & open
circuit the ideal current source (as shown in figure).
Example : 1
Find the current flowing
through R.
Short Circuiting Voltage

1. source V2 & finding the
current I1
Example : 1
Short Circuiting Voltage
2. source V1 & finding the
current I2
The net current is :-
Same answer is obtained by another method (shown below) which would turn
out to be tedious when applied to bigger circuits as in next example….
Example :2
R1 R2
15 V 100 W 20 W 13 V
V1 10 W R3 V2
R1 R2
15 V 100 W 20 W
V2 shorted
V1 10 W R3
REQ = 106.7 W, IT = 0.141 A and IR3 = 0.094 A

Example :2
R1 R2
15 V 100 W 20 W 13 V
V1 10 W R3 V2
R1 R2
100 W 20 W 13 V
V1 shorted
10 W R3 V2
REQ = 29.09 W, IT = 0.447 A and IR3 = 0.406 A

Example :2
R1 R2
15 V 100 W 20 W 13 V
V1 V2
0.094 A 0.406 A
With V2 shorted
REQ = 106.7 W, IT = 0.141 A and IR3 = 0.094 A
With V1 shorted
REQ = 29.09 W, IT = 0.447 A and IR3 = 0.406 A
Adding the currents gives IR3 = 0.5 A

Example :2
R1 R2
15 V 100 W 20 W 13 V
V1 10 W R3 V2
0.5 A
With 0.5 A flowing in R3, the voltage across R3 must

be 5 V (Ohm’s Law). The voltage across R1 must
therefore be 10 volts (KVL) and the voltage across R2
must be 8 volts (KVL). Solving for the currents in R1
and R2 will verify that the solution agrees with KCL.
IR1 = 0.1 A and IR2 = 0.4 A
IR3 = 0.1 A + 0.4 A = 0.5 A

 Circuits Containing Independent as well as
Dependent Sources
• Consider only one source to be active at a time.
• Remove all other IDEAL INDEPENDENT VOLTAGE SOURCES by
SHORT CIRCUIT & all other IDEAL INDEPENDENTCURRENT
SOURCES by OPEN CIRCUIT - as per the original procedure of
superposition theorem
• BUT NEITHER SHORT CIRCUIT NOR OPEN
CIRCUIT THE DEPENDENT SOURCE. LEAVE
THEM INTACT AND AS THEY ARE
(a) Dependent Voltage Source
A voltage source whose parameters are controlled by voltage/current else
where in the system
v = µVx v = ρix
VDVS CDVS
(Voltage Dependent (Current Dependent
Voltage source) Voltage source)
(b) Dependent Current Source

A current source whose parameters are controlled by voltage/current else
where in the system
v = βix
v = αVx
CDCS
VDCS
(Current Dependent
(Voltage Dependent
Current source)
Current source)
Example : 3
Find i0 in the circuit shown below. The circuit involves a dependent source. The
current may be obtained as by using superposition as :
i’0 is current due to 4A current source

i’’0 is current due to 20V voltage source
 i0  i0'  i0''
14
To obtain i’0we short circuit the 20V i2
sources
i1
For loop 1
i1  4 A. i3
For loop 2
3(i2  i1 )  2i2  5i ' 0  1(i2  i3 )  0

For loop 3
5(i3  i1 )  1(i3  i2 )  5i0'  4i3  0

i' 0  i1  i 3
52
For solving i1, i2, i3 i0 
'
A
15 17
To obtain i’’0 , we open circuit the 4A sources
For loop 4
i4
6i 4  i 5  5i  0
''
0
For loop 5
- i 4  10i5  20  5i0''  0
i5
i0''  i5
For solving i4 and i5
60
i  A
''
Therefore, i 0  i '0  i '0'

0
17
52 60
 
17 17
8
 A
16 17
A LIMITATION :- Superposition is not applicable to
Power
The superposition theorem does not apply to power calculations as the power is
proportional to current squared or voltage squared. Consider the following :
I T  I1  I 2 The total power

The power delivered to the circuits are
must be
determined
P1  I12 R, P2  I 22 R, and PT  I T2 R
using the total
PT  ( I1  I 2 ) 2 R  I12 R  I 22 R  2 I1 I 2 R current not by
 P1  P2  I12 R  I 22 R superposition
17
THANK YOU

Superposition Theorem

Uploaded by

Copyright:

Available Formats

Superposition Theorem

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Superposition Theorem

Uploaded by

Copyright:

Available Formats

Topic :- Superposition Theorem

Short Circuiting Voltage

The net current is :-

REQ = 106.7 W, IT = 0.141 A and IR3 = 0.094 A

REQ = 29.09 W, IT = 0.447 A and IR3 = 0.406 A

Adding the currents gives IR3 = 0.5 A

With 0.5 A flowing in R3, the voltage across R3 must

IR1 = 0.1 A and IR2 = 0.4 A

IR3 = 0.1 A + 0.4 A = 0.5 A

(b) Dependent Current Source

i’0 is current due to 4A current source

3(i2  i1 )  2i2  5i ' 0  1(i2  i3 )  0

5(i3  i1 )  1(i3  i2 )  5i0'  4i3  0

Therefore, i 0  i '0  i '0'

I T  I1  I 2 The total power

You might also like