What is Geothermal Energy?

Mary H. Dickson and Mario Fanelli

Istituto di Geoscienze e Georisorse, CNR , Pisa, Italy

Prepared on February 2004

INTRODUCTION

Heat is a form of energy and geothermal energy is, literally, the heat contained

within the Earth that generates geological phenomena on a planetary scale. ‘Geothermal

energy’ is often used nowadays, however, to indicate that part of the Earth'
s heat that

can, or could, be recovered and exploited by man, and it is in this sense that we will use

the term from now on.

Brief geothermal history

The presence of volcanoes, hot springs, and other thermal phenomena must have led

our ancestors to surmise that parts of the interior of the Earth were hot. However, it was

not until a period between the sixteenth and seventeenth century, when the first mines

were excavated to a few hundred metres below ground level, that man deduced, from

simple physical sensations, that the Earth'

s temperature increased with depth.

The first measurements by thermometer were probably performed in 1740 by De

Gensanne, in a mine near Belfort, in France (Buffon, 1778). By 1870, modern scientific

methods were being used to study the thermal regime of the Earth (Bullard, 1965), but it

was not until the twentieth century, and the discovery of the role played by radiogenic

heat, that we could fully comprehend such phenomena as heat balance and the Earth'
s

thermal history. All modern thermal models of the Earth, in fact, must take into
account the heat continually generated by the decay of the long-lived radioactive

isotopes of uranium (U238, U235), thorium (Th232) and potassium (K40), which are

present in the Earth (Lubimova, 1968). Added to radiogenic heat, in uncertain

proportions, are other potential sources of heat such as the primordial energy of

planetary accretion. Realistic theories on these models were not available until the

1980s, when it was demonstrated that there was no equilibrium between the radiogenic

heat generated in the Earth'

s interior and the heat dissipated into space from the Earth,

and that our planet is slowly cooling down. To give some idea of the phenomenon

involved and its scale, we will cite a heat balance from Stacey and Loper (1988), in
12
which the total flow of heat from the Earth is estimated at 42 x 10 W (conduction,
12
convection and radiation). Of this figure, 8 x 10 W come from the crust, which

represents only 2% of the total volume of the Earth but is rich in radioactive isotopes,
12
32.3 x 10 W come from the mantle, which represents 82% of the total volume of the
12
Earth, and 1.7 x 10 W come from the core, which accounts for 16% of the total

volume and contains no radioactive isotopes. (See Figure 1 for a sketch of the inner

structure of the Earth). Since the radiogenic heat of the mantle is estimated at 22 x
12 12
10 W, the cooling rate of this part of the Earth is 10.3 x 10 W.

In more recent estimates, based on a greater number of data, the total flow of heat

from the Earth is about 6 percent higher than the figure utilized by Stacey and Loper in

1988. Even so, the cooling process is still very slow. The temperature of the mantle

has decreased no more than 300 to 350 °C in three billion years, remaining at

about 4000 °C at its base. It has been estimated that the total heat content of the Earth,

reckoned above an assumed average surface temperature of 15 °C, is of the order of

24 21
12.6 x 10 MJ, and that of the crust is of the order of 5.4 x 10 MJ (Armstead, 1983).

The thermal energy of the Earth is therefore immense, but only a fraction could be

2
utilized by mankind. So far our utilization of this energy has been limited to areas in

which geological conditions permit a carrier (water in the liquid phase or steam) to

‘transfer’ the heat from deep hot zones to or near the surface, thus giving rise to

geothermal resources; innovative techniques in the near future, however, may offer new

perspectives in this sector.

Figure 1
The Earth's crust, mantle, and core. Top right: a section through the crust and the
uppermost mantle.

In many areas of life, practical applications precede scientific research and

technological developments, and the geothermal sector is a good example of this. In the

early part of the nineteenth century the geothermal fluids were already being exploited

for their energy content. A chemical industry was set up in that period in Italy (in the

zone now known as Larderello), to extract boric acid from the boric hot waters

3
emerging naturally or from specially drilled shallow boreholes. The boric acid was

obtained by evaporating the boric waters in iron boilers, using the wood from nearby

forests as fuel. In 1827 Francesco Larderel, founder of this industry, developed a system

for utilising the heat of the boric fluids in the evaporation process, rather than burning

wood from the rapidly depleting forests (Figure 2).

Figure 2
The “covered lagoon” used in the first half of the 19th century in the Larderello area,
Italy, to collect the hot boric waters and extract the boric acid.

Exploitation of the natural steam for its mechanical energy began at much the same

time. The geothermal steam was used to raise liquids in primitive gas lifts and later in

reciprocating and centrifugal pumps and winches, all of which were used in drilling or

the local boric acid industry. Between 1850 and 1875 the factory at Larderello held the

monopoly in Europe for boric acid production. Between 1910 and 1940 the low-

pressure steam in this part of Tuscany was brought into use to heat the industrial and

residential buildings and greenhouses. Other countries also began developing their

geothermal resources on an industrial scale. In 1892 the first geothermal district heating

4
system began operations in Boise, Idaho (USA). In 1928 Iceland, another pioneer in the

utilization of geothermal energy, also began exploiting its geothermal fluids (mainly hot

waters) for domestic heating purposes.

By 1904 the first attempt was being made at generating electricity from geothermal

steam; again, it was to take place at Larderello (Figure 3).

Figure 3
The engine used at Larderello in 1904 in the first experiment in generating electric
energy from geothermal steam, along with its inventor, Prince Piero Ginori Conti.

The success of this experiment was a clear indication of the industrial value of

geothermal energy and marked the beginning of a form of exploitation that was to

develop significantly from then on. Electricity generation at Larderello was a

commercial success. By 1942 the installed geothermoelectric capacity had reached

127,650 kWe. Several countries were soon to follow the example set by Italy. In 1919

the first geothermal wells in Japan were drilled at Beppu, followed in 1921 by wells

drilled at The Geysers, California, USA. In 1958 a small geothermal power plant began

operating in New Zealand, in 1959 another began in Mexico, in 1960 in the USA,

followed by many other countries in the years to come.

5
Present status of geothermal utilization

After the Second World War many countries were attracted by geothermal energy,

considering it to be economically competitive with other forms of energy. It did not

have to be imported, and, in some cases, it was the only energy source available locally.

Table 1. Installed geothermal generating capacities world-wide from 1995 to 2000

(from Huttrer, 2001), and at the end of 2003.
Country 1995 2000 1995-2000 % 2003
(MWe) (MWe) (increase in increase (MWe)
MWe ) (1995-2000)
Argentina 0.67 - - - -
Australia 0.15 0.15 - - 0.15
Austria - - - - 1.25
China 28.78 29.17 0.39 1.35 28.18
Costa Rica 55 142.5 87.5 159 162.5
El Salvador 105 161 56 53.3 161
Ethiopia - 7 7 - 7
France 4.2 4.2 - - 15
Germany - - - - 0.23
Guatemala - 33.4 33.4 - 29
Iceland 50 170 120 240 200
Indonesia 309.75 589.5 279.75 90.3 807
Italy 631.7 785 153.3 24.3 790.5
Japan 413.7 546.9 133.2 32.2 560.9
Kenya 45 45 - - 121
Mexico 753 755 2 0.3 953
New Zealand 286 437 151 52.8 421.3
Nicaragua 70 70 - - 77.5
Papua New Guinea - - - - 6
Philippines 1227 1909 682 55.8 1931
Portugal 5 16 11 220 16
Russia 11 23 12 109 73
Thailand 0.3 0.3 - - 0.3
Turkey 20.4 20.4 - - 20.4
USA 2816.7 2228 - - 2020

Total 6833.35 7972.5 1728.54 16.7 8402.21

The countries that utilise geothermal energy to generate electricity are listed in

Table1, which also gives the installed geothermal electric capacity in 1995 (6833 MWe),

6
in 2000 (7972 MWe) and the increase between 1995 and the year 2000 (Huttrer, 2001).

The same Table also reports the total installed capacity at the end of 2003 (8402 MWe).

The geothermal power installed in the developing countries in 1995 and 2000 represents

38 and 47% of the world total, respectively.

The utilization of geothermal energy in developing countries has exhibited an

interesting trend over the years. In the five years between 1975 and 1979 the geothermal

electric capacity installed in these countries increased from 75 to 462 MWe; by the end

of the next five-year period (1984) this figure had reached 1495 MWe, showing a

rate of increase during these two periods of 500% and 223%, respectively (Dickson and

Fanelli, 1988). In the next sixteen years, from 1984 to 2000, there was a further

increase of almost 150%. Geothermal power plays a fairly significant role in the energy

balance of some areas; for example, in 2001 the electric energy produced from

geothermal resources represented 27% of the total electricity generated in the

Philippines, 12.4% in Kenya, 11.4% in Costa Rica, and 4.3% in El Salvador.

As regards non-electric applications of geothermal energy, Table 2 gives the

installed capacity (15,145 MWt) and energy use (190,699 TJ/yr) world-wide for the

year 2000. During that year 58 countries reported direct uses, compared to 28 in 1995

and 24 in 1985. The number of countries with direct uses has very likely increased since

then, as well as the total installed capacity and energy use.

The most common non-electric use world-wide (in terms of installed capacity) is heat

pumps (34.80%), followed by bathing (26.20%), space-heating (21.62%), greenhouses

(8.22%), aquaculture (3.93%), and industrial processes (3.13%) (Lund and Freeston,

2001).

7
Table 2. Non-electric uses of geothermal energy in the world (2000): installed thermal
power (in MWt) and energy use (in TJ/yr). Taken from Lund and Freeston (2001).
Country Power Energy
(MWt) (TJ/yr)
Algeria 100 1586
Argentina 25.7 449
Armenia 1.0 15
Australia 34.4 351
Austria 255.3 1609
Belgium 3.9 107
Bulgaria 107.2 1637
Canada 377.6 1023
Caribbean Islands 0.1 1
Chile 0.4 7
China 2282.0 37 908
Colombia 13.3 266
Croatia 113.9 555
Czech Republic 12.5 128
Denmark 7.4 75
Egypt 1.0 15
Finland 80.5 484
France 326.0 4895
Georgia 250.0 6307
Germany 397.0 1568
Greece 57.1 385
Guatemala 4.2 117
Honduras 0.7 17
Hungary 472.7 4086
Iceland 1469.0 20170
India 80.0 2517
Indonesia 2.3 43
Israel 63.3 1713
Italy 325.8 3774
Japan 1167.0 26933
Jordan 153.3 1540
Kenya 1.3 10
Korea 35.8 753
Lithuania 21.0 599
Macedonia 81.2 510
Mexico 164.2 3919
Nepal 1.1 22
Netherlands 10.8 57
New Zealand 307.9 7081
Norway 6.0 32
Peru 2.4 49
Philippines 1.0 25
Poland 68.5 275

8
Portugal 5.5 35
Romania 152.4 2871
Russia 308.2 6144
Serbia 80.0 2375
Slovak Republic 132.3 2118
Slovenia 42.0 705
Sweden 377.0 4128
Switzerland 547.3 2386
Thailand 0.7 15
Tunisia 23.1 201
Turkey 820.0 15756
United Kingdom 2.9 21
USA* 3766.0 20302
Venezuela 0.7 14
Yemen 1.0 15

Total 15145.0 190699

*
During 2003 these figures increased to 4350 MWt and 22,250 TJ/yr (Lund, 2003)

NATURE OF GEOTHERMAL RESOURCES

The Earth's thermal engine

The geothermal gradient expresses the increase in temperature with depth in the

Earth'
s crust. Down to the depths accessible by drilling with modern technology, i.e.

over 10,000 m, the average geothermal gradient is about 2.5-3 °C/100 m. For example,

if the temperature within the first few metres below ground-level, which on average

corresponds to the mean annual temperature of the external air, is 15 °C, then we can

reasonably assume that the temperature will be about 65°-75 °C at 2000 m depth, 90°-

105 °C at 3000 m and so on for a further few thousand metres. There are, however, vast

areas in which the geothermal gradient is far from the average value. In areas in which

the deep rock basement has undergone rapid sinking, and the basin is filled with

geologically ‘very young’ sediments, the geothermal gradient may be lower than 1

°C/100 m. On the other hand, in some ‘geothermal areas’ the gradient is more than ten

times the average value.

9
 The difference in temperature between deep hotter zones and shallow colder zones

generates a conductive flow of heat from the former towards the latter, with a tendency

to create uniform conditions, although, as often happens with natural phenomena, this

situation is never actually attained. The mean terrestrial heat flow of continents and
-2
oceans is 65 and 101 mWm , respectively, which, when areally weighted, yield a global
-2
mean of 87 mWm (Pollack et al., 1993). These values are based on 24,774

measurements at 20,201 sites covering about 62% of the Earth'

s surface. Empirical

estimators, referenced to geological map units, enabled heat flow to be estimated in

areas without measurements. The heat flow analysis by Pollack et al. (1993) is the most

recent in print form. The University of North Dakota is currently providing access via

internet to an updated heat flow database comprising data on oceanic and continental

areas.

The temperature increase with depth, as well as volcanoes, geysers, hot springs, etc.,

are in a sense the visible or tangible expression of the heat in the interior of the Earth,

but this heat also engenders other phenomena that are less discernible by man, but of

such magnitude that the Earth has been compared to an immense ‘thermal engine’. We

will try to describe these phenomena, referred to collectively as the plate tectonics

theory, in simple terms, and their relationship with geothermal resources.

Our planet consists of a crust, which reaches a thickness of about 20-65 km in

continental areas and about 5-6 km in oceanic areas, a mantle, which is roughly 2900

km thick, and a core, about 3470 km in radius (Figure 1). The physical and chemical

characteristics of the crust, mantle and core vary from the surface of the Earth to its

centre. The outermost shell of the Earth, known as the lithosphere, is made up of the

crust and the upper layer of the mantle. Ranging in thickness from less than 80 km in

oceanic zones to over 200 km in continental areas, the lithosphere behaves as a rigid

10
body. Below the lithosphere is the zone known as the asthenosphere, 200-300 km in

thickness, and of a ‘less rigid’ or ‘more plastic’ behaviour. In other words, on a

geological scale in which time is measured in millions of years, this part of the Earth

behaves in much the same way as a fluid in certain processes.

Because of the difference in temperature between the different parts of the

asthenosphere, convective movements and, possibly, convective cells were formed some

tens of millions of years ago. Their extremely slow movement (a few centimetres per

year) is maintained by the heat produced continually by the decay of the radioactive

elements and the heat coming from the deepest parts of the Earth. Immense volumes of

deep hotter rocks, less dense and lighter than the surrounding material, rise with these

movements towards the surface, while the colder, denser and heavier rocks near the

surface tend to sink, re-heat and rise to the surface once again, very similar to what

happens to water boiling in a pot or kettle.

In zones where the lithosphere is thinner, and especially in oceanic areas, the

lithosphere is pushed upwards and broken by the very hot, partly molten material

ascending from the asthenosphere, in correspondence to the ascending branch of

convective cells. It is this mechanism that created and still creates the spreading ridges

that extend for more than 60,000 km beneath the oceans, emerging in some places

(Azores, Iceland) and even creeping between continents, as in the Red Sea. A relatively

tiny fraction of the molten rocks upwelling from the asthenosphere emerges from the

crests of these ridges and, in contact with the seawater, solidifies to form a new oceanic

crust. Most of the material rising from the asthenosphere, however, divides into two

branches that flow in opposite directions beneath the lithosphere. The continual

generation of new crust and the pull of these two branches in opposite directions has

caused the ocean beds on either side of the ridges to drift apart at a rate of a few

11
centimetres per year. Consequently, the area of the ocean beds (the oceanic lithosphere)

tends to increase. The ridges are cut perpendicularly by enormous fractures, in some

cases a few thousand kilometres in length, called transform faults.

These phenomena lead to a simple observation: since there is apparently no increase

in the Earth'
s surface with time, the formation of new lithosphere along the ridges and

the spreading of the ocean beds must be accompanied by a comparable shrinkage of the

lithosphere in other parts of the globe. This is indeed what happens in subduction zones,

the largest of which are indicated by huge ocean trenches, such as those extending along

the western margin of the Pacific Ocean and the western coast of South America. In the

subduction zones the lithosphere folds downwards, plunges under the adjacent

lithosphere and re-descends to the very hot deep zones, where it is "digested" by the

mantle and the cycle begins all over again. Part of the lithospheric material returns to a

molten state and may rise to the surface again through fractures in the crust. As a

consequence, magmatic arcs with numerous volcanoes are formed parallel to the

trenches, on the opposite side to that of the ridges. Where the trenches are located in the

ocean, as in the Western Pacific, these magmatic arcs consist of chains of volcanic

islands; where the trenches run along the margins of continents the arcs consist of

chains of mountains with numerous volcanoes, such as the Andes. Figure 4 illustrates

the phenomena we have just described.

Spreading ridges, transform faults and subduction zones form a vast network that

divides our planet into six immense and several other smaller lithospheric areas or

plates (Figure 5). Because of the huge tensions generated by the Earth'
s thermal engine

12
 Figure 4

Schematic cross-section showing plate tectonic processes

and the asymmetry of the zones producing and consuming lithospheric material, these

plates drift slowly up against one another, shifting position continually.

Figure 5
World pattern of plates, oceanic ridges, oceanic trenches, subduction zones, and
geothermal fields. Arrows show the direction of movement of the plates towards the
subduction zones. (1) Geothermal fields producing electricity; (2) mid-oceanic ridges
crossed by transform faults (long transversal fractures); (3) subduction zones, where
the subducting plate bends downwards and melts in the asthenosphere.

13
 The margins of the plates correspond to weak, densely fractured zones of the

crust, characterised by an intense seismicity, by a large number of volcanoes and,

because of the ascent of very hot materials towards the surface, by a high terrestrial heat

flow. As shown in Figure 5, the most important geothermal areas are located around

plate margins.

Geothermal systems

Geothermal systems can therefore be found in regions with a normal or slightly

above normal geothermal gradient, and especially in regions around plate margins

where the geothermal gradients may be significantly higher than the average value. In

the first case the systems will be characterised by low temperatures, usually no higher

than 100 °C at economic depths; in the second case the temperatures could cover a wide

range from low to very high, and even above 400 °C.

What is a geothermal system and what happens in such a system? It can be described

schematically as ‘convecting water in the upper crust of the Earth, which, in a confined

space, transfers heat from a heat source to a heat sink, usually the free surface’

(Hochstein, 1990). A geothermal system is made up of three main elements: a heat

source, a reservoir and a fluid, which is the carrier that transfers the heat. The heat

source can be either a very high temperature (> 600 °C) magmatic intrusion that has

reached relatively shallow depths (5-10 km) or, as in certain low-temperature systems,

the Earth'
s normal temperature, which, as we explained earlier, increases with depth.

The reservoir is a volume of hot permeable rocks from which the circulating fluids

extract heat. The reservoir is generally overlain by a cover of impermeable rocks and

connected to a surficial recharge area through which the meteoric waters can replace or

partly replace the fluids that escape from the reservoir through springs or are extracted

14
by boreholes. The geothermal fluid is water, in the majority of cases meteoric water, in

the liquid or vapour phase, depending on its temperature and pressure. This water often

carries with it chemicals and gases such as CO2, H2S, etc. Figure 6 is a greatly

simplified representation of an ideal geothermal system.

Figure 6
Schematic representation of an ideal geothermal system.

The mechanism underlying geothermal systems is by and large governed by fluid

convection. Figure 7 describes schematically the mechanism in the case of an

intermediate-temperature hydrothermal system. Convection occurs because of the

heating and consequent thermal expansion of fluids in a gravity field; heat, which is

supplied at the base of the circulation system, is the energy that drives the system.

Heated fluid of lower density tends to rise and to be replaced by colder fluid of high

density, coming from the margins of the system.

15
 Figure 7
Model of a geothermal system. Curve 1 is the reference curve for the boiling point of
pure water. Curve 2 shows the temperature profile along a typical circulation route
from recharge at point A to discharge at point E (From White, 1973).

Convection, by its nature, tends to increase temperatures in the upper part of a system as

temperatures in the lower part decrease (White, 1973).

The phenomenon we have just described may seem quite a simple one but the

reconstruction of a good model of a real geothermal system is by no means easy

to achieve. It requires skill in many disciplines and a vast experience, especially when

dealing with high -temperature systems. Geothermal systems also occur in nature in a

variety of combinations of geological, physical and chemical characteristics, thus giving

rise to several different types of system.

Of all the elements of a geothermal system, the heat source is the only one that need

be natural. Providing conditions are favourable, the other two elements could be

‘artificial’. For example, the geothermal fluids extracted from the reservoir to drive the

turbine in a geothermal power-plant could, after their utilization, be injected back into

16
the reservoir through specific injection wells. In this way the natural recharge of the

reservoir is integrated by an artificial recharge. For many years now re-injection has also

been adopted in various parts of the world as a means of drastically reducing the impact

on the environment of geothermal plant operations.

Artificial recharge through injection wells can also help to replenish and maintain

‘old’ or ‘exhausted’ geothermal fields. For example, in The Geysers field in California,

USA, one of the biggest geothermal fields in the world, production began to decline

dramatically at the end of the 1980s because of a lack of fluids. The first project of this

type, the Southeast Geysers Effluent Recycling Project, was launched in 1997, to

transport treated wastewater for 48 km to the geothermal field. This project has led to

the reactivation of a number of power plants that had been abandoned because of a lack

of fluids. In the second system, the Santa Rosa Geysers Recharge Project, 41.5 million

litres per day of tertiary treated waste-water will be pumped from the Santa Rosa

regional sewage treatment plant and other cities through a 66-km pipeline to The

Geysers field, where it will recharge the reservoir through specially drilled boreholes.

In the so-called Hot Dry Rock (HDR) projects, which were experimented for the first

time at Los Alamos, New Mexico, USA, in 1970, both the fluid and the reservoir are

artificial. High-pressure water is pumped through a specially drilled well into a deep

body of hot, compact rock, causing its hydraulic fracturing. The water permeates these

artificial fractures, extracting heat from the surrounding rock, which acts as a natural

reservoir. This '

reservoir'is later penetrated by a second well, which is used to extract

the heated water. The system therefore consists of (i) the borehole used for hydraulic

fracturing, through which cold water is injected into (ii) the artificial reservoir, and (iii)

the borehole used to extract the hot water. The entire system, complete with surface

utilization plant, could form a closed loop (Garnish, 1987) (see Figure 8).

17
 Figure 8
Schematic of a commercial-scale Hot Dry Rock.

The Los Alamos project was the forerunner for other similar projects in Australia,

France, Germany, Japan and the UK. After a period of relative neglect, these projects

have been given renewed impulse from the discovery, firstly, that deep rocks have a

certain degree of natural fracturation, and further, that the methodologies and

technologies adopted will depend on local geologic conditions. The most advanced

research in the HDR sector was that being conducted in Japan and under the European

project at Alsace (France). Several projects launched in Japan in the 1980s (at Hijiori,

Ogachi and Yunomori), and heavily financed by the Japanese government and industry,

have produced interesting results both from the scientific and industrial standpoints. The

European HDR project, on the other hand, has been implemented over a number of

phases, including the drilling of two wells, one of which has reached bottom-hole at

5060 m. Very promising results have been obtained from their geophysical surveys and

18
hydraulic tests, and the European Project seems, for the moment, to be the most

successful (Tenzer, 2001).

DEFINITION AND CLASSIFICATION OF GEOTHERMAL

RESOURCES

There is no standard international terminology in use throughout the geothermal

community, which is unfortunate, as this would facilitate mutual comprehension. The

following are some of the most common definitions and classifications in this discipline.

According to Muffler and Cataldi (1978), when we speak generically about

geothermal resources, what we are usually referring to is what should more accurately

be called the accessible resource base; that is, all of the thermal energy stored between

the Earth'
s surface and a specified depth in the crust, beneath a specified area and

measured from local mean annual temperature. The accessible resource base includes

the useful accessible resource base (= Resource ) — that part of the accessible resource

base that could be extracted economically and legally at some specified time in the

future (less than a hundred years). This category includes the identified economic

resource (= Reserve ) — that part of the resources of a given area that can be extracted

legally at a cost competitive with other commercial energy sources and that are known

and characterised by drilling or by geochemical, geophysical and geological evidence.

Figure 9 illustrates in graphic form these and other terms that may be used by

geothermal specialists.

19
 Figure 9
Diagram showing the different categories of geothermal resources. (From Muffler and
Cataldi, 1978). The vertical axis is the degree of economic feasibility; the horizontal
axis is the degree of geological assurance.

The most common criterion for classifying geothermal resources is, however, that

based on the enthalpy of the geothermal fluids that act as the carrier transporting heat

from the deep hot rocks to the surface. Enthalpy, which can be considered more or less

proportional to temperature, is used to express the heat (thermal energy) content of the

fluids, and gives a rough idea of their '

value'
. The resources are divided into low,

medium and high enthalpy (or temperature) resources, according to criteria that are

generally based on the energy content of the fluids and their potential forms of

utilization. Table 3 reports the classifications proposed by a number of authors. A

20
standard method of classification, as with terminology, would avoid confusion and

ambiguity but, until such a method exists, we must indicate the temperature values or

ranges involved case by case, since terms such as low, intermediate and high are

meaningless at best, and frequently misleading.

Table 3. Classification of geothermal resources (°C)

(a) (b) (c) (d) (e)
Low enthalpy resources < 90 <125 <100 150 190
Intermediate enthalpy 90-150 125-225 100-200 - -
resources
High enthalpy resources >150 >225 >200 >150 >190

Source: (a) Muffler and Cataldi (1978).

(b) Hochstein (1990).
(c) Benderitter and Cormy (1990).
(d) Nicholson (1993).
(e) Axelsson and Gunnlaugsson (2000)

Frequently a distinction is made between water- or liquid-dominated geothermal

systems and vapour-dominated (or dry steam) geothermal systems (White, 1973). In

water-dominated systems liquid water is the continuous, pressure-controlling fluid

phase. Some vapour may be present, generally as discrete bubbles. These geothermal

systems, whose temperatures may range from < 125 to > 225 °C, are the most widely

distributed in the world. Depending on temperature and pressure conditions, they can

produce hot water, water and steam mixtures, wet steam and, in some cases, dry steam.

In vapour-dominated systems liquid water and vapour normally co-exist in the reservoir,

with vapour as the continuous, pressure-controlling phase. Geothermal systems of this

type, the best-known of which are Larderello in Italy and The Geysers in California, are

somewhat rare, and are high-temperature systems. They normally produce dry-to-

superheated steam.

21
 The terms wet, dry and superheated steam, which are used frequently by

geothermists, need some explanation for readers who are not of an engineering

background. To make it as simple as possible, let us take the example of a pot filled

with liquid water in which pressure can be kept constant at 1 atm (101.3 kPa). If we then

heat the water, it will begin boiling once it reaches a temperature of 100 °C (boiling

temperature at a pressure of 1 atm) and will pass from the liquid to the gas (vapour)

phase. After a certain time the pot will contain both liquid and vapour. The vapour

coexisting with the liquid, and in thermodynamic equilibrium with it, is wet steam. If we

continue to heat the pot and maintain the pressure at 1 atm, the liquid will evaporate

entirely and the pot will contain steam only. This is what we call dry steam. Both wet

and dry steam are called “saturated steam”. Finally, increasing the temperature to, say,

120 °C, and keeping the pressure at 1 atm, we will obtain superheated steam with a

superheating of 20 °C, i.e. 20 °C above the vaporisation temperature at that pressure. At

other temperatures and pressures, of course, these phenomena also take place in the

underground, in what one author many years ago called “nature'

s tea-kettle”.

Another division between geothermal systems is that based on the reservoir

equilibrium state (Nicholson, 1993), considering the circulation of the reservoir fluid

and the mechanism of heat transfer. In the dynamic systems the reservoir is continually

recharged by water that is heated and then discharged from the reservoir either to the

surface or into underground permeable formations. Heat is transferred through the

system by convection and circulation of the fluid. This category includes high-

temperature (>150 °C) and low-temperature (<150 °C) systems. In the static systems

(also known as stagnant or storage systems) there is only minor or no recharge to the

reservoir and heat is transferred only by conduction. This category includes low-

temperature and geopressured systems. The geopressured systems are characteristically

22
found in large sedimentary basins (e.g. Gulf of Mexico, USA) at depths of 3 - 7 km. The

geopressured reservoirs consist of permeable sedimentary rocks, included within

impermeable low-conductivity strata, containing pressurized hot water that remained

trapped at the moment of deposition of the sediments. The hot water pressure

approaches lithostatic pressure, greatly exceeding the hydrostatic pressure. The

geopressured reservoirs can also contain significant amounts of methane. The

geopressured systems could produce thermal and hydraulic energy (pressurized hot

water) and methane gas. These resources have been investigated extensively, but so far

there has been no industrial exploitation.

Geothermal field is a geographical definition, usually indicating an area of

geothermal activity at the earth’s surface. In cases without surface activity this term may

be used to indicate the area at the surface corresponding to the geothermal reservoir

below (Axelsson and Gunnlaugsson, 2000).

As geothermal energy is usually described as renewable and sustainable, it is

important to define these terms. Renewable describes a property of the energy source,

whereas sustainable describes how the resource is utilised.

The most critical factor for the classification of geothermal energy as a renewable

energy source is the rate of energy recharge. In the exploitation of natural geothermal

systems, energy recharge takes place by advection of thermal water on the same time

scale as production from the resource. This justifies our classification of geothermal

energy as a renewable energy resource. In the case of hot, dry rocks, and some of the hot

water aquifers in sedimentary basins, energy recharge is only by thermal conduction;

due to the slow rate of the latter process, however, hot dry rocks and some sedimentary

reservoirs should be considered as finite energy resources (Stefansson, 2000).

23
 The sustainability in consumption of a resource is dependent on its original quantity,

its rate of generation and its rate of consumption. Consumption can obviously be

sustained over any period of time in which a resource is being created faster than it is

being depleted. The term sustainable development is used by the World Commission on

Environment and Development to indicate development that ‘….meets the needs of the

present generation without compromising the needs of future generations’. In this

context, sustainable development does not imply that any given energy resource needs

to be used in a totally sustainable fashion, but merely that a replacement for the resource

can be found that will allow future generations to provide for themselves despite the fact

that the particular resource has been depleted. Thus, it may not be necessary that a

specific geothermal field be exploited in sustainable fashion. Perhaps we should direct

our geothermal sustainability studies towards reaching and then sustaining a certain

overall level of geothermal production at a national or regional level, both for electric

power generation and direct heat applications, for a certain period, say 300 years, by

bringing new geothermal systems on line as others are depleted (Wright, 1998).

EXPLORATION

Objectives of exploration

The objectives of geothermal exploration are (Lumb, 1981):

1. To identify geothermal phenomena.

2. To ascertain that a useful geothermal production field exists.

3. To estimate the size of the resource.

4. To determine the type of geothermal field.

5. To locate productive zones.

24
 6. To determine the heat content of the fluids that will be discharged by the wells in

the geothermal field.

7. To compile a body of basic data against which the results of future monitoring can

be viewed.

8. To determine the pre-exploitation values of environmentally sensitive parameters.

9. To acquire knowledge of any characteristics that might cause problems during

field development.

The relative importance of each objective depends on a number of factors, most of

which are tied to the resource itself. These include anticipated utilization, technology

available, economics, as well as situation, location and time, all of which affect the

exploration programme. For example, the preliminary reconnaissance of geothermal

manifestations assumes much greater importance in a remote, unexplored area than in a

well-known area; estimating the size of the resource may be less important if it is to be

used in a small-scale application that obviously requires much less heat than is already

discharging naturally; if the energy is to be used for district-heating or some other

application needing low-grade heat, then a high-temperature fluid is no longer an

important objective (Lumb, 1981).

A large number of methods and technologies are available in order to reach these

objectives. Many of these methods are in current use and have already been widely

experimented in other sectors of research. The techniques and methodologies that have

proved successful in mineral and oil or gas exploration will however not necessarily be

the best solution in geothermal exploration. Conversely, techniques of little use in oil

exploration could turn out to be ideal tools in the search for natural heat (Combs and

Muffler, 1973).

25
Exploration methods

Geological and hydrogeological studies are the starting point of any exploration

programme, and their basic function is that of identifying the location and extension of

the areas worth investigating in greater detail and of recommending the most suitable

exploration methods for these areas. Geological and hydrogeological studies have an

important role in all subsequent phases of geothermal research, right up to the siting of

exploratory and producing boreholes. They also provide the background information for

interpreting the data obtained with the other exploration methods and, finally, for

constructing a realistic model of the geothermal system and assessing the potential of

the resource. The information obtained from the geological and hydrogeological studies

may also be used in the production phase, providing valuable information for the

reservoir and production engineers. The duration and cost of exploration can be

appreciably reduced by a good exploration programme and an efficient coordination of

the research.

Geochemical surveys (including isotope geochemistry) are a useful means of

determining whether the geothermal system is water- or vapour-dominated, of

estimating the minimum temperature expected at depth, of estimating the homogeneity

of the water supply, of inferring the chemical characteristics of the deep fluid, and of

determining the source of recharge water. Valuable information can also be obtained on

the type of problems that are likely to arise during the re-injection phase and plant

utilization (e.g. changes in fluid composition, corrosion and scaling on pipes and plant

installations, environmental impact) and how to avoid or combat them. The geochemical

survey consists of sampling and chemical and/or isotope analyses of the water and gas

from geothermal manifestations (hot springs, fumaroles, etc.) or wells in the study area.

As the geochemical survey provides useful data for planning exploration and its cost is

26
relatively low compared to other more sophisticated methods, such as the geophysical

surveys, the geochemical techniques should be utilised as much as possible before

proceeding with other more expensive methodologies.

Geophysical surveys are directed at obtaining indirectly, from the surface or from

depth intervals close to the surface, the physical parameters of deep geological

formations. These physical parameters include:

• temperature (thermal survey)

• electrical conductivity (electrical and electromagnetic methods)

• propagation velocity of elastic waves (seismic survey)

• density (gravity survey)

• magnetic susceptibility (magnetic survey).

Some of these techniques, such as seismics, gravity and magnetics, which are

traditionally adopted in oil research, can give valuable information on the shape, size,

depth and other important characteristics of the deep geological structures that could

constitute a geothermal reservoir, but they give little or no indication as to whether these

structures actually contain the fluids that are the primary objective of research. These

methodologies are, therefore, more suited to defining details during the final stages of

exploration, before the exploratory wells are sited. Information on the existence of

geothermal fluids in the geological structures can be obtained with the electrical and

electromagnetic prospectings, which are more sensitive than the other surveys to the

presence of these fluids and to variations in temperature; these two techniques have

been applied widely with satisfactory results. The magnetotelluric method, which

exploits the electromagnetic waves generated by solar storms, has been greatly

improved over the last few years, and now offers a vast spectrum of possible

applications, despite the fact that it requires sophisticated instrumentation and is

27
sensitive to background noise in urbanised areas. The main advantage of the

magnetotelluric method is that it can be used to define deeper structures than are

attainable with the electric and the other electro-magnetic techniques. The Controlled

Source Audiomagnetotelluric method (CSAMT), developed recently, uses artificially

induced waves instead of natural electro-magnetic waves. The penetration depth is

shallower with this technique, but it is quicker, cheaper, and provides far more detail

than the classic MT method.

Thermal techniques (temperature measurements, determination of geothermal

gradient and terrestrial heat flow) can often provide a good approximation of the

temperature at the top of the reservoir.

All geophysical techniques are expensive, although some more than others. Nor can

they be used indiscriminately in any situation or condition, as a method that produces

excellent results in a determinate geological environment may give very unsatisfactory

results in another. In order to reduce costs, it is therefore very important that the

geophysical method(s) be selected very carefully beforehand by geophysicists working

in close collaboration with geologists (Meidav, 1998).

Drilling of exploratory wells represents the final phase of any geothermal exploration

programme and is the only means of determining the real characteristics of the

geothermal reservoir and thus of assessing its potential (Combs and Muffler, 1973). The

data provided by exploratory wells should be capable of verifying all the hypotheses and

models elaborated from the results of surface exploration and of confirming that the

reservoir is productive and that it contains enough fluids of adequate characteristics for

the utilization for which it is intended. Siting of the exploratory wells is therefore a very

delicate operation.

28
Exploration programme

Before drawing up a geothermal exploration programme all existing geological,

geophysical and geochemical data must be collected and integrated with any data

available from previous studies on water, minerals and oil resources in the study area

and adjacent areas. This information frequently plays an important role in defining the

objectives of the geothermal exploration programme and could lead to a significant

reduction in costs.

The exploration programme is usually developed on a step-by-step basis:

reconnaissance, pre-feasibility and feasibility. During each of these phases we gradually

eliminate the less interesting areas and concentrate on the most promising ones. The

methods used also become progressively more sophisticated and more detailed as the

programme develops. The size and budget of the entire programme should be

proportional to its objectives, to the importance of the resources we expect to find, and

to the planned forms of utilization. The programme schedule should be flexible and

reassessed as the results come in from the various surveys of each phase; similarly the

geological-geothermal model should be progressively updated and improved. These

periodic re-assessments of the programme should ideally eliminate any operations that

are no longer necessary and insert others, according to the results attained at each stage.

Clearly any reduction in the number and size of the prospectings will lead to a decrease

in costs, and also a corresponding increase in the risk of error or failure. Conversely, by

decreasing the risk of error we increase the overall cost. The economic success of a

geothermal exploration programme hinges on finding the proper balance between the

two.

29
UTILIZATION OF GEOTHERMAL RESOURCES

Electricity generation is the most important form of utilization of high-temperature

geothermal resources (> 150 °C). The medium-to-low temperature resources (< 150 °C)

are suited to many different types of application. The classical Lindal diagram (Lindal,

1973), which shows the possible uses of geothermal fluids at different temperatures, still

holds valid (Figure 10, derived from the original Lindal diagram, with the addition of

electricity generation from binary cycles. Fluids at temperatures below 20 °C are rarely

used and in very particular conditions, or in heat pump applications. The Lindal diagram

emphasises two important aspects of the utilization of geothermal resources

(Gudmundsson, 1988): (a) with cascading and combined uses it is possible to enhance

the feasibility of geothermal projects and (b) the resource temperature may limit the

possible uses. Existing designs for thermal processes can, however, be modified for

geothermal fluid utilization in certain cases, thus widening its field of application.

Figure 10
Diagram showing the utilization of geothermal fluids (derived from Lindal, 1973)

30
Electricity generation

Electricity generation mainly takes place in conventional steam turbines and binary

plants, depending on the characteristics of the geothermal resource.

Conventional steam turbines require fluids at temperatures of at least 150 °C and are

available with either atmospheric (back-pressure) or condensing exhausts. Atmospheric

exhaust turbines are simpler and cheaper. The steam, direct from dry steam wells or,

after separation, from wet wells, is passed through a turbine and exhausted to the

atmosphere (Figure 11).

Figure 11
Sketch of an atmospheric exhaust geothermal power-plant. The flow of geothermal fluid
is indicated in red.

With this type of unit, steam consumption (from the same inlet pressure) per

kilowatt-hour produced is almost double that of a condensing unit. However, the

atmospheric exhaust turbines are extremely useful as pilot plants, stand-by plants, in the

case of small supplies from isolated wells, and for generating electricity from test wells

during field development. They are also used when the steam has a high non-

condensable gas content (>12% in weight). The atmospheric exhaust units can be

constructed and installed very quickly and put into operation in little more than 13-14

31
months from their order date. This type of machine is usually available in small sizes

(2.5 - 5 MWe).

The condensing units, having more auxiliary equipment, are more complex than the

atmospheric exhaust units and the bigger sizes can take twice as long to construct and

install. The specific steam consumption of the condensing units is, however, about half

that of the atmospheric exhaust units. Condensing plants of 55 - 60 MWe capacity are

very common, but recently plants of 110 MWe have also been constructed and installed

(Figure 12).

Figure 12
Sketch of a condensing geothermal power-plant. The flow of high-temperature fluid is
indicated in red, and the cooling water in blue.

Generating electricity from low-to-medium temperature geothermal fluids and from

the waste hot waters coming from the separators in water - dominated geothermal

fields has made considerable progress since improvements were made in binary fluid

technology. The binary plants utilize a secondary working fluid, usually an organic fluid

(typically n-pentane), that has a low boiling point and high vapour pressure at low

temperatures when compared to steam. The secondary fluid is operated through a

32
conventional Rankine cycle (ORC): the geothermal fluid yields heat to the secondary

fluid through heat exchangers, in which this fluid is heated and vaporises; the vapour

produced drives a normal axial flow turbine, is then cooled and condensed, and the

cycle begins again (Figure 13).

Figure 13
Sketch of a geothermal binary power plant. The flow of geothermal fluid is in red, the
secondary fluid in green, and the cooling water in blue.

By selecting suitable secondary fluids, binary systems can be designed to utilise

geothermal fluids in the temperature range 85-170 °C. The upper limit depends on the

thermal stability of the organic binary fluid, and the lower limit on technical-economic

factors: below this temperature the size of the heat exchangers required would render

the project uneconomical. Apart from low-to-medium temperature geothermal fluids

and waste fluids, binary systems can also be utilised where flashing of the geothermal

fluids should preferably be avoided (for example, to prevent well sealing). In this case,

down-hole pumps can be used to keep the fluids in a pressurised liquid state, and the

energy can be extracted from the circulating fluid by means of binary units.

33
 Binary plants are usually constructed in small modular units of a few hundred kWe to

a few MWe capacity. These units can then be linked up to create power-plants of a few

tens of megawatts. Their cost depends on a number of factors, but particularly on the

temperature of the geothermal fluid produced, which influences the size of the turbine,

heat exchangers and cooling system. The total size of the plant has little effect on the

specific cost, as a series of standard modular units is joined together to obtain larger

capacities.

Binary plant technology is a very cost-effective and reliable means of converting into

electricity the energy available from water-dominated geothermal fields (below 170 °C).

A new binary system, the Kalina cycle, which utilizes a water-ammonia mixture as

working fluid, was developed in the 1990s. The working fluid is expanded, in super-

heated conditions, through the high-pressure turbine and then re-heated before entering

the low-pressure turbine. After the second expansion the saturated vapour moves

through a recuperative boiler before being condensed in a water-cooled condenser. The

Kalina cycle is more efficient than existing geothermal ORC binary power plants, but is

of more complex design.

Small mobile plants, conventional or not, can not only reduce the risk inherent to

drilling new wells but, what is more important, they can help in meeting the energy

requirements of isolated areas. The standard of living of many communities could be

considerably improved were they able to draw on local sources of energy. Electricity

could facilitate many apparently banal, but extremely important operations, such as

pumping water for irrigation, freezing fruit and vegetables for longer conservation.

The convenience of the small mobile plants is most evident for areas without ready

access to conventional fuels, and for communities that would be too expensive to

connect to the national electric grid, despite the presence of high voltage transmission

34
lines in the vicinity. The expense involved in serving these small by-passed

communities is prohibitive, since the step-down transformers needed to tap electricity

from high voltage lines cost more than US$ 675,000 each, installed, and the simplest

form of local distribution of electricity, at 11 kV using wooden poles, costs a minimum

of US$ 20,000 per kilometre (US$ 1994). By comparison, the capital cost (US$ 1998)

of a binary unit is of the order of 1500-2500 US$/kW installed, excluding drilling costs.

The demand for electric capacity per person at off-grid sites will range from 0.2 kW in

less-developed areas to 1.0 kW or higher in developed areas. A 100 kWe plant could

serve 100 to 500 people. A 1000 kWe plant would serve 1000 to 5000 people (Entingh

et al., 1994).

Direct heat uses

Direct heat use is one of the oldest, most versatile and also the most common form of

utilization of geothermal energy (Table 2). Bathing, space and district heating,

agricultural applications, aquaculture and some industrial uses are the best known forms

of utilization, but heat pumps are the most widespread (12.5% of the total energy use in

2000). There are many other types of utilization, on a much smaller scale, some of

which are unusual.

Space and district heating have made great progress in Iceland, where the total

capacity of the operating geothermal district heating system had risen to about 1200

MWt by the end of 1999 (Figure 14), but they are also widely distributed in the East

European countries, as well as in the United States, China, Japan, France, etc.

35
 Figure 14
Simplified flow diagram of the geothermal district heating system of Reykjavik. (From
Gudmundsson, 1988)

Geothermal district heating systems are capital intensive. The main costs are initial

investment costs, for production and injection wells, down-hole and transmission

pumps, pipelines and distribution networks, monitoring and control equipment, peaking

stations and storage tanks. Operating expenses, however, are comparatively lower than

in conventional systems, and consist of pumping power, system maintenance, control

and management. A crucial factor in estimating the initial cost of the system is the

thermal load density, or the heat demand divided by the ground area of the district. A

high heat density determines the economic feasibility of a district heating project, since

the distribution network is expensive. Some economic benefit can be achieved by

combining heating and cooling in areas where the climate permits. The load factor in a

system with combined heating and cooling would be higher than the factor for heating

alone, and the unit energy price would consequently improve (Gudmundsson, 1988).

36
 Space cooling is a feasible option where absorption machines can be adapted to

geothermal use. The technology of these machines is well known, and they are readily

available on the market. The absorption cycle is a process that utilises heat instead of

electricity as the energy source. The refrigeration effect is obtained by utilising two

fluids: a refrigerant, which circulates, evaporates and condenses, and a secondary fluid

or absorbent. For applications above 0 °C (primarily in space and process conditioning),

the cycle uses lithium bromide as the absorbent and water as the refrigerant. For

applications below 0 °C an ammonia/water cycle is adopted, with ammonia as the

refrigerant and water as the absorbent. Geothermal fluids provide the thermal energy to

drive these machines, although their efficiency decreases with temperatures lower than

105 °C.

Figure 15
Typical application of ground-coupled heat pump system (from Sanner et al., 2003).

37
 Geothermal space conditioning (heating and cooling) has expanded considerably

since the 1980s, following on the introduction and widespread use of heat pumps. The

various systems of heat pumps available permit us to economically extract and utilise

the heat content of low-temperature bodies, such as the ground and shallow aquifers,

ponds, etc. (Sanner, 2001) (see, for example, Figure 15).

As engineers already know, heat pumps are machines that move heat in a direction

opposite to that in which it would tend to go naturally, i.e. from a cold space or body to

a warmer one. A heat pump is effectively nothing more than a refrigeration unit

(Rafferty, 1997). Any refrigeration device (window air conditioner, refrigerator, freezer,

etc.) moves heat from a space (to keep it cool) and discharges that heat at higher

temperatures. The only difference between a heat pump and a refrigeration unit is the

desired effect, cooling for the refrigeration unit and heating for the heat pump. A second

distinguishing factor of many heat pumps is that they are reversible and can provide

either heating or cooling in the space. The heat pumps, of course, need energy to

operate, but in suitable climatic conditions and with a good design, the energy balance

will be a positive one (Figure 16).

Ground-coupled and ground-water heat pump systems have now been installed in

great numbers in at least 30 countries, for a total thermal capacity of more than 9500

MWt (in 2003). The majority of these installations are in the USA (500,000 installations

for a total of 3730 MWt), Sweden (200,000 installations totalling 2000 MWt), Germany

(40,000 installations totalling 560 MWt ), Canada (36,000 installations totalling 435

MWt), Switzerland (25,000 installations totalling 440 MWt), and Austria (23,000

installations totalling 275 MWt) (Lund et al., 2003). Aquifers and soils with

temperatures in the 5 to 30 °C range are being used in these systems.

38
 Figure 16
Sketch of a heat pump in heating mode (courtesy of the Geo-Heat Center, Klamath
Falls, Oregon, USA)

The agricultural applications of geothermal fluids consist of open-field agriculture

and greenhouse heating. Thermal water can be used in open-field agriculture to irrigate

and/or heat the soil. The greatest drawback in irrigating with warm waters is that, to

obtain any worthwhile variation in soil temperature, such large quantities of water are

required at temperatures low enough to prevent damage to the plants that the fields

would be flooded. One possible solution to this problem is to adopt a subsurface

irrigation system coupled to a buried-pipeline soil-heating device. Heating the soil in

buried pipelines without the irrigation system could decrease the heat conductivity of

the soil, because of the drop in humidity around the pipes, and consequent thermal

insulation. The best solution seems to be that of combining soil heating and irrigation.

The chemical composition of the geothermal waters used in irrigation must be

monitored carefully to avoid adverse effects on the plants. The main advantages of

temperature control in open-field agriculture are: (a) it prevents any damage ensuing

39
from low environmental temperatures, (b) it extends the growing season, increases plant

growth, and boosts production, and (c) it sterilises the soil (Barbier and Fanelli, 1977).

The most common application of geothermal energy in agriculture is, however, in

greenhouse heating, which has been developed on a large scale in many countries. The

cultivation of vegetables and flowers out-of-season, or in an unnatural climate, can now

draw on a widely experimented technology. Various solutions are available for

achieving optimum growth conditions, based on the optimum growth temperature of

each plant (Figure 17), and on the quantity of light, on the CO2 concentration in the

greenhouse environment, on the humidity of the soil and air, and on air movement.

Figure 17
Growth curves for some crops. (From Beall and Samuels, 1971)

The walls of the greenhouse can be made of glass, fibreglass, rigid plastic panels or

plastic film. Glass panels are more transparent than plastic and will let in far more light,

but will provide less thermal insulation, are less resistant to shocks, and are heavier and

more expensive than the plastic panels. The simplest greenhouses are made of single

40
plastic films, but recently some greenhouses have been constructed with a double layer

of film separated by an air space. This system reduces the heat loss through the walls by

30 - 40%, and thus greatly enhances the overall efficiency of the greenhouse.

Greenhouse heating can be accomplished by forced circulation of air in heat exchangers,

hot-water circulating pipes or ducts located in or on the floor, finned units located along

the walls and under benches, or a combination of these methods (Figure 18).

Figure 18
Heating systems in geothermal greenhouses. Heating installations with natural air
movement ((natural convection): (a) aerial pipe heating; (b) bench heating; (c) low-
position heating pipes for aerial heating. (d) Soil heating. Heating installations with
forced air movement (forced convection): (e) lateral position;(f) aerial fan; (g) high-
position ducts; (h) low-position ducts. (From von Zabeltitz, 1986.)

41
 Exploitation of geothermal heat in greenhouse heating can considerably reduce their

operating costs, which in some cases account for 35% of the product costs (vegetables,

flowers, house-plants and tree seedlings).

Farm animals and aquatic species, as well as vegetables and plants, can benefit in

quality and quantity from optimum conditioning of their environmental temperature

(Figure 19). In many cases geothermal waters could be used profitably in a combination

of animal husbandry and geothermal greenhouses. The energy required to heat a

breeding installation is about 50% of that required for a greenhouse of the same surface

area, so a cascade utilization could be adopted. Breeding in a temperature-controlled

environment improves animal health, and the hot fluids can also be utilised to clean,

sanitise and dry the animal shelters and waste products (Barbier and Fanelli, 1977).

Figure 19
Effect of temperature on growth or production of food animals. (From Beall and
Samuels, 1971).

42
 Aquaculture , which is the controlled breeding of aquatic forms of life, is gaining

world-wide importance nowadays, due to an increasing market demand. Control of the

breeding temperatures for aquatic species is of much greater importance than for land

species, as can be seen in Figure 19, which shows that the growth curve trend of aquatic

species is very different from that of land species. By maintaining an optimum

temperature artificially we can breed more exotic species, improve production and

even, in some cases, double the reproductive cycle (Barbier and Fanelli, 1977). The

species that are typically raised are carp, catfish, bass, tilapia, mullet, eels, salmon,

sturgeon, shrimp, lobster, crayfish, crabs, oysters, clams, scallops, mussels and abalone.

Aquaculture also includes alligator and crocodile breeding, as tourist attractions and

for their skins, which could prove a lucrative activity. Past experience in the United

States has shown that, by maintaining its growth temperature at about 30 °C, an alligator

can be grown to a length of about 2 m in 3 years, whereas alligators bred under natural

conditions will reach a length of only 1.2 m over the same period. These reptiles have

been bred on farms in Colorado and Idaho for some years now, and the Icelanders are

planning something similar.

The temperatures required for aquatic species are generally in the 20 - 30 °C range.

The size of the installation will depend on the temperature of the geothermal source, the

temperature required in the fish ponds and the heat losses from the latter.

The cultivation of Spirulina can also be considered a form of aquaculture. This

single-celled, spiral-shaped, blue-green micro-algae is frequently called ‘super-food’

because of its nutrient density; it has also been proposed to solve the problem of famine

in the poorest countries of the world, although at the moment it is being marketed as a

nutritional food supplement. Spirulina is now being farmed in a number of tropical and

sub-tropical countries, in lakes or artificial basins, where conditions are ideal for its fast

43
and widespread growth (a hot, alkaline environment rich in CO2). Geothermal energy

has already been used successfully to provide the heat needed to grow Spirulina

throughout the year in temperate countries.

The entire temperature range of geothermal fluids, whether steam or water, can be

exploited in industrial applications, as shown in the Lindal diagram (Figure 10). The

different possible forms of utilization include process heating, evaporation, drying,

distillation, sterilisation, washing, de-icing, and salt extraction. Industrial process heat

has applications in 19 countries (Lund and Freeston, 2001), where the installations tend

to be large and energy consumption high. Examples also include concrete curing,

bottling of water and carbonated drinks, paper and vehicle parts production, oil

recovery, milk pasteurisation, leather industry, chemical extraction, CO2 extraction,

laundry use, diatomaceous earth drying, pulp and paper processing, and borate and boric

acid production. There are also plans to utilise low-temperature geothermal fluids to de-

ice runaways and disperse fog in some airports. A cottage industry has developed in

Japan that utilises the bleaching properties of the H2S in geothermal waters to produce

innovative and much admired textiles for ladies'clothing. In Japan they have also

experimented a technique for manufacturing a lightweight '

geothermal wood'that is

particularly suited to certain types of constructions. During treatment in the hot spring

water the polysaccharides in the original wood hydrolise, rendering the material more

porous and thus lighter.

Economic considerations

The elements that have to be considered in any cost estimate, whether assigned to

plant or operating costs, and the price of the '

products'of geothermal energy, are all

more numerous and more complicated than in other forms of energy. All these elements

must nevertheless be carefully evaluated before launching a geothermal project. We can

44
only offer a few indications of a more general character, which, together with

information on local conditions and on the value of the geothermal fluids available,

should help the potential investor to reach a decision.

A resource-plant system (geothermal power facility) consists of the geothermal

wells, the pipelines carrying the geothermal fluids, the utilization plant and,

frequently, a re-injection system as well. The interaction of all these elements bears

heavily on investment costs, and must therefore be subjected to careful analysis. To

give an example, in the generation of electricity, a discharge-to-the-atmosphere plant

is the simplest solution, and is therefore cheaper than a condensing plant of the same

capacity. It will, however, require almost twice as much steam as the condensing

plant to operate, and, consequently, twice as many wells to feed it. Since wells are

very expensive, a condensing power plant is effectively a cheaper option than the

discharge-to-atmosphere plant. The latter is, in fact, usually chosen for reasons other

than economy.

Geothermal fluids can be transported over fairly long distances in thermally

insulated pipelines. In ideal conditions, the pipelines can be as long as 60 km.

However, the pipelines, the ancillary equipment needed (pumps, valves, etc.), and

their maintenance, are all quite expensive, and could weigh heavily on the capital

cost and operating costs of a geothermal plant. The distance between the resource

and the utilization site should therefore be kept as small as possible.

The capital cost of a geothermal plant is usually higher, and sometimes much higher,

than that of a similar plant run on a conventional fuel. Conversely, the energy

45
 driving a geothermal plant costs far less than conventional fuel, and corresponds to

the cost of maintaining the geothermal elements of the plant (pipelines, valves,

pumps, heat exchangers, etc.). The higher capital outlay should be recovered by the

savings in energy costs. The resource-plant system should therefore be designed to

last long enough to amortise the initial investment and, wherever possible, even

longer.

Appreciable savings can be achieved by adopting integrated systems that offer a

higher utilization factor (for example, combining space-heating and cooling) or

cascade systems, where the plants are connected in series, each utilising the waste

water from the preceding plant (for example, electricity generation + greenhouse

heating + animal husbandry) (Figure 20).

Figure 20
Cascade uses of geothermal energy (courtesy of the Geo-Heat Center, Klamath Falls,
Oregon, USA)

46
 In order to reduce maintenance costs and shut-downs, the technical complexity of

the plant should be on a level that is accessible to local technical personnel or to

experts who are readily available. Highly specialised technicians or the

manufacturers should ideally be needed only for large-scale maintenance operations

or major breakdowns.

Finally, if the geothermal plant is to produce consumer products, a careful market

survey must be carried out beforehand to guarantee an outlet for these products. The

necessary infrastructures for the economic transport of the end-product from the

production site to the consumer should already exist, or be included in the initial

project.

Table 4. Energy and investment costs for electric energy production from renewables
(from Fridleifsson, 2001)
Current energy Potential future Turnkey
cost energy cost investment cost
US¢/kWh US¢/kWh US$/kW
Biomass 5 - 15 4 - 10 900 - 3000
Geothermal 2 - 10 1-8 800 - 3000
Wind 5 - 13 3 - 10 1100 - 1700
Solar (photovoltaic) 25 - 125 5 - 25 5000 - 10 000
Solar (thermal electricity) 12 - 18 4 - 10 3000 - 4000
Tidal 8 – 15 8 – 15 1700 - 2500

The foregoing observations can be applied to any form of utilization of geothermal

energy and any local conditions and are therefore of a purely qualitative nature. For a

quantitative idea of investments and costs we recommend the World Energy Assessment

Report, prepared by UNDP, UN-DESA and the World Energy Council, and published in

47
2000. The WEA data are given in Tables 4 and 5, which also compare geothermal

energy with other renewable forms of energy (Fridleifsson, 2001).

Table 5. Energy and investment costs for direct heat from renewables (from
Fridleifsson, 2001)
Current Potential future Turnkey
energy cost energy cost investment cost
US¢/kWh US¢/kWh US$/kW
Biomass (including ethanol) 1-5 1-5 250 - 750
Geothermal 0.5 - 5 0.5 - 5 200 - 2000
Wind 5 - 13 3 - 10 1100 - 1700
Solar heat low temperature 3 - 20 2 - 10 500 - 1700

ENVIRONMENTAL IMPACT

During the 1960s, when our environment was healthier than it is nowadays and we

were less aware of any threat to the earth, geothermal energy was still considered a

'
clean energy'
. There is actually no way of producing or transforming energy into a form

that can be utilised by man without making some direct or indirect impact on the

environment. Even the oldest and simplest form of producing thermal energy, i.e.

burning wood, has a detrimental effect, and deforestation, one of the major problems in

recent years, first began when our ancestors cut down trees to cook their food and heat

their houses. Exploitation of geothermal energy also has an impact on the environment,

but there is no doubt that it is one of the least polluting forms of energy.

Sources of pollution

In most cases the degree to which geothermal exploitation affects the environment is

proportional to the scale of its exploitation (Lunis and Breckenridge,1991). Table 6

summarises the probability and relative severity of the effects on the environment of

developing geothermal direct-use projects. Electricity generation in binary cycle plants

48
will affect the environment in the same way as direct heat uses. The effects are

potentially greater in the case of conventional back-pressure or condensing power-

plants, especially as regards air quality, but can be kept within acceptable limits.

Table 6. Probability and severity of potential environmental impact of direct-use

projects
Impact Probability of occurring Severity of consequences
Air quality pollution L M
Surface water pollution M M
Underground pollution L M
Land subsidence L L to M
High noise levels H L to M
Well blow-outs L L to M
Conflicts with cultural and L to M M to H
archaeological features
Social-economic problems L L
Chemical or thermal pollution L M to H
Solid waste disposal M M to H

L = Low; M = Moderate; H= High

Source: Lunis and Breckenridge (1991)

Any modification to our environment must be evaluated carefully, in deference to the

relevant laws and regulations (which in some countries are very severe), but also

because an apparently insignificant modification could trigger a chain of events whose

impact is difficult to fully assess beforehand. For example, a mere 2-3 °C increase in the

temperature of a body of water as a result of discharging the waste water from a

utilization plant could damage its ecosystem. The plant and animal organisms that

are most sensitive to temperature variations could gradually disappear, leaving a fish

species without its food source. An increase in water temperature could impair

development of the eggs of other fish species. If these fish are edible and provide the

necessary support for a community of fishermen, then their disappearance could be

critical for the community at large.

49
 The first perceptible effect on the environment is that of drilling, whether the

boreholes are shallow ones for measuring the geothermal gradient in the study phase, or

exploratory/producing wells. Installation of a drilling rig and all the accessory

equipment entails the construction of access roads and a drilling pad. The latter will
2
cover an area ranging from 300—500 m for a small truck-mounted rig (max. depth
2
300—700 m) to 1200—1500 m for a small-to-medium rig (max. depth of 2000 m).

These operations will modify the surface morphology of the area and could damage

local plants and wildlife. Blow-outs can pollute surface water; blow-out preventers

should be installed when drilling geothermal wells where high temperatures and

pressures are anticipated (Lunis and Breckenridge, 1991). During drilling or flow-tests

undesirable gases may be discharged into the atmosphere. The impact on the

environment caused by drilling mostly ends once drilling is completed.

The next stage, installation of the pipelines that will transport the geothermal fluids,

and construction of the utilization plants, will also affect animal and plant life and the

surface morphology. The scenic view will be modified, although in some areas such as

Larderello, Italy, the network of pipelines criss-crossing the countryside and the power-

plant cooling towers have become an integral part of the panorama and are indeed a

famous tourist attraction.

Environmental problems also arise during plant operation. Geothermal fluids (steam

or hot water) usually contain gases such as carbon dioxide (CO2), hydrogen sulphide

(H2S), ammonia (NH3), methane (CH4), and trace amounts of other gases, as well as

dissolved chemicals whose concentrations usually increase with temperature. For

example, sodium chloride (NaCl), boron (B), arsenic (As) and mercury (Hg) are a

source of pollution if discharged into the environment. Some geothermal fluids, such as

those utilised for district-heating in Iceland, are freshwaters, but this is very rare. The

50
waste waters from geothermal plants also have a higher temperature than the

environment and therefore constitute a potential thermal pollutant.

Air pollution may become a problem when generating electricity in conventional

power-plants. Hydrogen sulphide is one of the main pollutants. The odour threshold for

hydrogen sulphide in air is about 5 parts per billion by volume and subtle physiological

effects can be detected at slightly higher concentrations (Weres, 1984). Various

processes, however, can be adopted to reduce emissions of this gas. Carbon dioxide is

also present in the fluids used in the geothermal power plants, although much less CO2

is discharged from these plants than from fossil-fuelled power stations: 13 – 380 g for

every kWh of electricity produced in the geothermal plants, compared to the 1042

g/kWh of the coal-fired plants, 906 g/kWh of oil-fired plants, and 453 g/kWh of natural

gas-fired plants (Fridleifsson, 2001). Binary cycle plants for electricity generation and

district-heating plants may also cause minor problems, which can virtually be overcome

simply by adopting closed-loop systems that prevent gaseous emissions.

Discharge of waste waters is also a potential source of chemical pollution. Spent

geothermal fluids with high concentrations of chemicals such as boron, fluoride or

arsenic should be treated, re-injected into the reservoir, or both. However, the low-to-

moderate temperature geothermal fluids used in most direct-use applications generally

contain low levels of chemicals and the discharge of spent geothermal fluids is seldom a

major problem. Some of these fluids can often be discharged into surface waters after

cooling (Lunis and Breckenridge, 1991). The waters can be cooled in special storage

ponds or tanks to avoid modifying the ecosystem of natural bodies of waters (rivers,

lakes and even the sea).

Extraction of large quantities of fluids from geothermal reservoirs may give rise to

subsidence phenomena, i.e. a gradual sinking of the land surface. This is an irreversible

51
phenomenon, but by no means catastrophic, as it is a slow process distributed over vast

areas. Over a number of years the lowering of the land surface could reach detectable

levels, in some cases of the order of a few tens of centimetres and even metres, and

should be monitored systematically, as it could damage the stability of the geothermal

buildings and any private homes in the neighbourhood. In many cases subsidence can be

prevented or reduced by re-injecting the geothermal waste waters.

The withdrawal and/or re-injection of geothermal fluids may trigger or increase the

frequency of seismic events in certain areas. However these are microseismic events

that can only be detected by means of instrumentation. Exploitation of geothermal

resources is unlikely to trigger major seismic events, and so far has never been known to

do so.

The noise associated with operating geothermal plants could be a problem where the

plant in question generates electricity. During the production phase there is the higher

pitched noise of steam travelling through pipelines and the occasional vent discharge.

These are normally acceptable. At the power plant the main noise pollution comes from

the cooling tower fans, the steam ejector, and the turbine '
hum'(Brown, 2000). The

noise generated in direct heat applications is usually negligible.

PRESENT AND FUTURE

The thermal energy present in the underground is enormous. A group of experts has

estimated (Table 7) the geothermal potential of each continent in terms of high- and

low-temperature resources (International Geothermal Association, 2001).

52
Table 7. Geothermal potential world-wide (IGA, 2001).
High-temperature resources suitable for Low-temperature
electricity generation resources suitable
for direct use in
million TJ/yr of
heat (lower limit)
Conventional Conventional and binary
technology in technology in TWh/yr of
TWh/yr of electricity
electricity
Europe 1830 3700 > 370
Asia 2970 5900 > 320
Africa 1220 2400 > 240
North America 1330 2700 > 120
Latin America 2800 5600 > 240
Oceania 1050 2100 > 110

World potential 11 200 22 400 > 1400

If exploited correctly, geothermal energy could certainly assume an important role in

the energy balance of some countries. In certain circumstances even small-scale

geothermal resources are capable of solving numerous local problems and of raising the

living standards of small isolated communities.

The data reported by Fridleifson (2003) give some idea of the role played by

geothermal energy with respect to other renewable energy sources: of the total

electricity produced from renewables in 1998, i.e. 2826 TWh, 92% came from hydro

power, 5.5% from biomass, 1.6% from geothermal, 0.6% from wind, 0.05% from solar,

and 0.02% from tidal. Biomass constitutes 93% of the total direct heat production from

renewables, geothermal represents 5% and solar heating 2%.

REFERENCES

ARMSTEAD, H.C.H., 1983. Geothermal Energy. E. & F. N. Spon, London, 404 pp.

53
AXELSSON, G. and GUNNLAUGSSON, E., 2000. Background: Geothermal

utilization, management and monitoring. In: Long-term monitoring of high- and low

enthalpy fields under exploitation, WGC 2000 Short Courses, Japan, 3-10.

BARBIER, E. and FANELLI, M., 1977. Non-electrical uses of geothermal energy.

Prog. Energy Combustion Sci., 3, 73-103.

BEALL, S. E, and SAMUELS, G., 1971. The use of warm water for heating and cooling

plant and animal enclosures. Oak Ridge National Laboratory, ORNL-TM-3381,

56 pp.

BENDERITTER, Y. and CORMY, G., 1990. Possible approach to geothermal research

and relative costs. In:Dickson, M.H. and Fanelli, M., eds., Small Geothermal

Resources: A Guide to Development and Utilization, UNITAR, New York, pp. 59—

69.

BROWN, K. L., 2000. Impacts on the physical environment. In: Brown, K.L., ed.,

Environmental Safety and Health Issues in Geothermal Development, WGC 2000

Short Courses, Japan, 43—56.

BUFFON, G.L., 1778. Histoire naturelle, générale et particulière. Paris, Imprimerie

Royale, 651 p.

BULLARD, E.C., 1965. Historical introduction to terrestrial heat flow. In : Lee,

W.H.K., ed. Terrestrial Heat Flow, Amer. Geophys. Un., Geophys. Mon. Ser., 8,

pp.1-6.

COMBS, J. and MUFFLER, L.P.J., 1973. Exploration for geothermal resources. In :

Kruger, P. and Otte, C., eds., Geothermal Energy, Stanford University Press,

Stanford, pp.95—128.

54
ENTINGH, D. J., EASWARAN, E. and McLARTY, L., 1994. Small geothermal

electric systems for remote powering. U.S. DoE, Geothermal Division, Washington,

D.C., 12 pp.

FRIDLEIFSSON, I.B., 2001. Geothermal energy for the benefit of the people.

Renewable and Sustainable Energy Reviews, 5, 299-312.

FRIDLEIFSSON, I. B., 2003. Status of geothermal energy amongst the world’s energy

sources. IGA News, No.52, 13-14.

GARNISH, J.D., ed., 1987. Proceedings of the First EEC/US Workshop on Geothermal

Hot-Dry Rock Technology, Geothermics 16, 323—461.

GUDMUNDSSON, J.S., 1988. The elements of direct uses. Geothermics, 17,119—136.

HOCHSTEIN, M.P., 1990. Classification and assessment of geothermal resources. In:

Dickson, M.H. and Fanelli, M., eds., Small Geothermal Resources: A Guide to

Development and Utilization, UNITAR, New York, pp. 31—57.

HUTTRER, G.W., 2001. The status of world geothermal power generation 1995-2000.

Geothermics, 30, 7-27.

INTERNATIONAL GEOTHERMAL ASSOCIATION, 2001. Report of the IGA to the

UN Commission on Sustainable Development, Session 9 (CSD-9), New York, April.

LINDAL, B., 1973. Industrial and other applications of geothermal energy. In:

Armstead, H.C.H., ed., Geothermal Energy, UNESCO, Paris, pp.135—148.

LUBIMOVA, E.A., 1968. Thermal history of the Earth. In: The Earth's Crust and

Upper Mantle, Amer. Geophys. Un., Geophys. Mon. Ser., 13, pp.63—77.

LUMB, J. T., 1981. Prospecting for geothermal resources. In: Rybach, L. and Muffler,

L.J.P., eds., Geothermal Systems, Principles and Case Histories, J. Wiley & Sons,

New York, pp. 77—108.

55
LUND, J. W., SANNER, B., RYBACH, L., CURTIS, R., HELLSTROM, G., 2003.

Ground-source heat pumps. Renewable Energy World, Vol.6, no.4, 218-227.

LUND, J. W., 2003. The USA country update. IGA News, No. 53, 6-9.

LUND, J. W., and BOYD, T. L., 2001. Direct use of geothermal energy in the U.S. –

2001. Geothermal Resources Council Transactions, 25, 57-60.

LUND, J. W., and FREESTON, D., 2001. World-wide direct uses of geothermal energy

2000. Geothermics 30, 29- 68.

LUNIS, B. and BRECKENRIDGE, R., 1991. Environmental considerations. In: Lienau,

P.J. and Lunis, B.C.,eds., Geothermal Direct Use, Engineering and Design Guidebook,

Geo-Heat Center, Klamath Falls, Oregon, pp.437—445.

MEIDAV,T.,1998. Progress in geothermal exploration technology. Bulletin Geothermal

Resources Council, 27, 6,178-181.

MUFFLER, P. and CATALDI, R., 1978. Methods for regional assessment of

geothermal resources. Geothermics , 7, 53—89.

NICHOLSON, K., 1993. Geothermal Fluids. Springer Verlag, Berlin, XVIII—264 pp.

POLLACK, H.N., HURTER, S.J. and JOHNSON, J.R.,1993. Heat flow from the Earth'
s

interior: Analysis of the global data set. Rev. Geophys. 31, 267—280.

RAFFERTY, K., 1997. An information survival kit for the prospective residential

geothermal heat pump owner. Bull. Geo-Heat Center , 18, 2, 1—11.

SANNER, B., KARYTSAS, C., MENDRINOS, D. and RYBACH, L., 2003. Current

status of ground source heat pumps and underground thermal energy storage.

Geothermics, Vol.32, 579-588.

STACEY, F.D. and LOPER, D.E., 1988. Thermal history of the Earth: a corollary

concerning non-linear mantle rheology. Phys. Earth. Planet. Inter. 53, 167 - 174.

56
STEFANSSON,V., 2000. The renewability of geothermal energy. Proc. World

Geothermal Energy, Japan. On CD-ROM

TENZER, H., 2001. Development of hot dry rock technology. Bulletin Geo-Heat

Center, 32, 4, 14-22.

WERES, O., 1984. Environmental protection and the chemistry of geothermal fluids.

Lawrence Berkeley Laboratory, Calif. , LBL 14403, 44 pp.

WHITE, D. E., 1973. Characteristics of geothermal resources. In: Kruger, P. and Otte,

C.,eds., Geothermal Energy, Stanford University Press, Stanford, pp. 69-94.

WRIGHT, P.M., 1998. The sustainability of production from geothermal resources.

Bull. Geo-Heat Center, 19, 2, 9-12.

57