Inst Over Current

Download as pdf or txt
Download as pdf or txt
You are on page 1of 20

GE I-28803G

INSTRUCTIONS

INSTANTANEOUS OVERCURRENT RELAYS

Types

PJCI1N
lix
pJcilz
PJC11AT
PJC1IAV
PJC1IAW
PJC12D
PJC12E
PJC12N
PJC12R
PJC12U
PJC13E
PJC13H
PJC13J
PJC14C
PJCI4E

GE Meter and Control


205 Great Valley Parkway
Malvern, PA 19355-1337
GEI-28803

INSTANTANEOUS OVERCURRENT RELAYS


TYPE PJC

APPL I CATION

The Type PJC plunger relays are designed for general service. These relays are non
directional and instantaneous when in operation.

Type NC relays are normally used for overcurrent protection of feeder circuits;
they can also be used for various current control functions. When these relays are
used in conjunction with thermal or time—overcurrent relays, they can be used to
protect a motor against very high currents, since they will operate before the main
relays respond. The AC relays are applicable where continuous operation in the
pickup position is not required.

CHARACTERISTICS

Characteristic time-current curves are shown in Figure 1.

The pickup of current relays without taps (1.5, 3, 6, 12 amperes) is adjustable from
1/3 to 1-1/3 of the continuous rating up to and including the 12 ampere rating. The
calibration ranges of the tapped coil (5, 10 amperes) and higher current untapped
coil (25 amperes) relays are listed in Table 11 under BURDENS.

The contacts reset at approximately 90 to 95% of the pickup on AC circuits when


using the contact arrangement of one normally-open contact and one normally—closed
contact. For DC circuits, the dropout is 60 to 90% of the pickup current. These
values are not adjustable; however, a slight change could be made by varying the
contact pressures (refer to ADJUSTMENTS in the INSTALLATION section).

RATINGS
CON TACTS

The carrying rating of the contacts is 5 amperes continuously or 30 amperes for


tripping. The interrupting ratings of the contacts are shown in Table I.

TABLE I

DC AC
Volts 24 48 125 250 115 230 460
Amps 5 2 1 0.3 5 2

These instructions do not purport to cover all detaiLs or variations in rquipnt nor to provide for
every possible ccatingenc’ to be met in connection with installation, operation or aIntenanC.. Should
further information be desired or should particulCr probieire arise which are not covered sufficiently for
the purchasers purposes, the matter should be reterred to the General £J.ctric Co)any.
To the extent required the products described herein meet applicable ANSI. IStS and NFMA standards,
but no such assurance is given with respect to local codes and ordinances because they varj greatly.

2
GE 1—28803

COILS
These coils are suitable
The ratings of the standard coils are listed listed below.
for DC and frequencies from 25 to 60 cycles.

Tapped: 5 and 10 amperes


Untapped: 1.5, 3, 6, 12 and 25 amperes

BURDENS
OPERATING COiLS
TABLE II

Rated Calibration VA at 5 amps W at 5 amps W at 5 amps


Range 60 Cycles 60 Cycles DC
Amps.
0.5— 2 165 55 24
1.5
1 4 41 12.7 6
3 -

5 2 —50 9.6 5.3 1.98


6 2 - 8 11.5 3.56 1.6
4 -100 2.65 0.8 0.43
10
4 16 2.65 0.8 0.43
12 -

25 10 -40 0.4 0.125 0.08


20 80 0.1 0.03 0.056
25 -

40 -160 0.025 0.008 0.025


L 25
applied on the minimum pickup
VA and W in the dropout position, with pickup current
y 1.7 and 0.6, respec tively.
setting at 60 cycles, are approximatel

AUXILIARY COILS
and 1 ampere coils are 6.1 and 0.24 ohms,
The resistance of the 0.2 ampere
respectively.
RECEIVING, HANDLING AND STORAGE
l panel, will be shipped in
These relays, when not included as part of a contro
e. immediately upon receipt of a
cartons designed to protect them against damag If injury or damage
transit.
relay, examine it for any damage sustained in
a damag e claim at once with the
resulting from rough handling is evident, file Genera l Electric Sales
neares t
transportation company and promptly notify the
Office.
relay in order that none of the
Reasonable care should be exercised in unpacking the
parts are injured or the adjustments disturbed.
should be stored in their
If the relays are not to be installed immediately, they
re, dust and metallic chips.
original cartons in a place that is free from moistu
find its way inside when the
Foreign matter collected on the outside of the case may
on of the relay.
cover is removed, and cause trouble in the operati

3
GEI-28803

CONSTRUCT ION

The Type PJC relays consist of one or more units mounted in a metal case. The units
are of the plunger type and have an adjustable pickup current range. The moving
contacts are fastened to a TEXTOLITE R contact barrier that is molded to the plunger
rod. The armature assembly is positioned by a calibrating tube that is assembled to
a magnet frame. These parts, together with a coil, pole piece, stationary contacts
and a target, are assembled on a molded TEXTOLITE R base. In some units, there is
an additional coil mounted on the magnet frame, which is part of a hinged-armature
element. This coil performs an electrical holding function, keeping the plunger-rod
assembly and the target in the operated (picked up) position until the holding coil
is de-energized.

The types of relays summarized in Table III have any of a combination of the
following features: one or more relay units; two or four contacts; with or without
a mechanical or electrical target, and electrical holding; self or hand reset of
contacts and coils; with or without taps.

TABLE III

. Target Outline
No. of Contacts M Mech Reset Size & Panel mt.
Type Relay Each Unit E Elec. H Hand Coil Holding of Drilling Conn..
Units No. Code 0 None S Self Taps Coil Case Figs. Figs.

PJC11M 1 2 all N S X - Si 13 2
PJC11X 3 2 all N S X — M2 16 4
PJC11Z 3 2 all N S — - M2 16 5
PJC11AT 3 2 ii M-O S - - M2 16 12
PJC11AV 1 2 all M—O S - — Si 13 3
PJC11AW 2 2 all M—O S — — S2 14 6
PJCJ2D 1 2 all N H - — Si 13 3
PJC12E 1 2 all N H X — Si 13 2
PJC12N 2 2 all N H — — S2 14 6
PJC12R 3 2 all N H — — M2 16 5
PJC12U 2 2 all N *S H - - S2 14 6
PJC13E 3 2 all E S — X Mi 15 7
PJC13H 2 2 all E S - X S2 14 8
PJC13J 1 2 all E S — X Si 13 9
PJC14C 1 4 all N S — — Si 13 11
PJC14E 1 4 all E S — X S2 14 10

*
Left unit, self reset; Right unit, hand reset.

The Types PJC12D, 12E, i2N, 12R, and 12U have a hand contact reset feature. When
the relay operates, a latch drops into place to hold the plunger up. When the relay
is in the latched-up position, the normally-closed contacts will be open, but the
normally-open contacts may, or may not, be closed. The relay is reset by pushing
the reset button.

All targets are provided with external reset buttons, which also reset the contacts
of hand-reset types of relays.

4
GEI—28803

CASE
and an
The case is suitable for either surface or semi-flush panel mounting,
hardware is provided for either mounting. The cover attache s to the
assortment of
carries the reset mechanism when one is require d. Each cover screw
case and also
has provision for a sealing wire.

The case has studs or screw connections at both ends, or at the bottom only, for the
external connections. The electrical connections between the relay units and the
stationary
case studs are made through spring-backed contact fingers mounted in
molded inner and outer blocks, between which nests a removable connec ting plug that
d
The outer blocks, attache to the case, have the studs for
completes the circuits.
have the termin als for the internal
the external connections, and the inner blocks
connections.
and is a
The relay mechanism is mounted in a steel framework called the cradle,
This cradle is
complete unit, with all leads being terminated at the inner block.
by a guide pin at
held firmly in the case by a latch at the top and the bottom and
the back of the case. The cases and cradles are so constructed that the relay
s making the
cannot be inserted in the case upside down. The connecting plug, beside
tive blocks of the cradle and case, also
electrical connections between the respec
The cover, which is fastene d to the case by
locks the lower latch in place.
thurnbscrews, holds the connec ting plug in place.
drawn out;
To draw out the relay unit, the cover is first removed, then the plug
t transformer circuits.)
(Shorting bars are provided in the case to short the curren
easily drawn out. To replace
the latches are then released, and relay unit can be
the relay unit, the reverse order is followed.
plug to test the
A separate testing plug can be inserted in place of the connecting
voltage, or
relay in place on the panel, either from its own source of current and
Or, the relay unit can be drawn out and replace d by another
from other sources.
that has been tested in the laboratory.
INSTALLATION

LOCATION
vibration, and
The location should be clean and dry, free from dust and excessive
well lighted to facilitate inspection and testing.

MOUNTING

The relay should be mounted on a vertical surface. The outline and panel drilling
diagrams for each model are referre d to in Table III.

conductor
One of the mounting studs or screws should be permanently grounded by a
not less than #12 B&S gage copper wire or its equivalent.

5
GEI-28803

CONNECTIONS

The internal connection diagrams for the various relays are referred to in Table
‘II.

All relays, except those having three units, are provided with shorting bars on the
individual contacts and operating coils. The shorting bars on the coils are
required to prevent opening the secondary of the current transformer when the
connection plug is withdrawn. The shorting bars on the contacts are arranged to be
optional , and an internal connection lead is provided to make the extra connection.
For example, Figure 2 for the Type PJC11M relay shows that one end of the connection
lead on terminal 3 can be connected to terminal 1 (see dotted line). Then, if
terminals 2 and 3 are used, the contacts will be shorted out when the plug is
removed. When terminals 1 and 2 are used, the connection between terminals 1 and 3
should be removed.

ADJUSTMENTS

The relays have been adjusted at the factory; however, before they are put into
operation, it is advisable to check each relay to be sure that the adjustments have
not been disturbed. If they have, the following points should be observed in
restoring them.

CONTACTS

The normal adjustment of contacts will give 3/64 inch wipe. This may be adjusted by
bending the contact stops that are located between the stationary cGntact springs
and the ribs on the molded base. The bend should be made about 1/4 inch from the
front tip of the stop. A change in wipe on the normally-closed contacts affects the
pickup for a given armature setting in the de-energized position. A decrease in
wipe will increase the pickup, and an increase in wipe will decrease the pickup
value. The normal wipe should not be exceeded, since this produces excessive
creeping of the armature below the pickup value of the relay. Another undesirable
effect is reduction of contact gap.

The contact pressure at the maximum pickup or dropout positions may be adjusted by
bending the stationary-contact springs, near the part attached to the base. This
adjustment may change the contact gap and contact wipe slightly. Adjustment of the
contact stops within the normal range does not affect the contact pressure at the
maximum pickup or dropout positions, because the contact springs are separated from
the stops in these positions.

When there is one normally-open and one normally-closed contact, the initial tension
should be adjusted for 15 grams, measured at the contact tip. If there are two
normally—open or two normally-closed contacts, the initial tension must be reduced
to 5 grams.

AUXILIARY HOLDING UNIT

The holding unit is normally adjusted to keep the plunger in the operated (picked
up) position after the main coil has been de-energized. If adjustment is required,
the pole piece should be set, while in the operated position, so that there us
approximately 1/32 inch of gap between its end and the surface of the armature. The

6
GEI-28803

slotted end of the pole piece is accessible through a hole in the top of the magnet
frame. The locknut provided should be tightened after the proper setting has been
The holding unit should operate at 80% of its nameplate rating. If a
obtained.
target is provided, it should operate and be in full view when the holding coil is
energized.
OPERATION

In these types of relay, the moving contacts are operated directly by the plunger
assembly. For models provided with an electrical target, the target has no
armature
mechanical relation with the plunger assembly; instead, it is lifted by the
All targets rise, when lifted, whether mechanical or
of the auxiliary element.
target shield to a position where the target face is
electrical, from behind the
visible. The target is latched up in the exposed position until reset by hand.

The electrical holding of a target is provided by an auxiliary armature holding up


the plunger assembly when the auxiliary coil is energized. This auxiliary coil is
not intended to lift the plunger from the de-energized position.

Hand-reset contact action is made possible by passing the target wires through
the
When the plunger armature is
two pins located at the bottom of the plunger rod.
is lifted and is held by the target latch. The top
attracted upward, the target
rod from dropping until the latch is disturbed by
target pin prevents the plunger
the manual movement of the reset button on the relay cover.

S ETT I NG
the
Any desired setting, within the calibrating ranges, may be obtained by turning
armature on the plunger rod. The armature is provided with an interna l locking
spring which requires no adjustments.
as
For relays with tapped coils, the pickup depends on the tap connection as well
the armature setting. The pickup values for all Type PJC relays are given on the
nameplate. This is the value at which the relay will just pick up and close its “a”
contacts if the armature is adjusted to the calibrating mark in the de-energized
05 i ti Ofl.

PERIODIC CHECKS AND ROUTINE MAINTENANCE

In view of the vital role of protective relays in the operation of a power system,
it is important that a periodic test program be followed. The interval between
periodic checks will vary depending upon environment , type of relay and the user’s
experience with periodic testing. Until the user has accumulated enough experience
to select the test interval best suited to his individual requirements , it is
listed under ADJUSTME NTS in the INSTALLAT ION section be
suggested that the points
checked at least once every six months.

CONTACT CLEANING
This
For cleaning fine silver contacts, a flexible burnishing tool should be used.
of metal with an etched-rough ened surface, resembling
consists of a flexible strip
in effect a superfine file. The polishing action is so delicate that no scratches
are left, yet corroded material will be removed rapidly and thoroughly. The
flexibility of the tool ensures the cleaning of the actual points of contact.

7
GEI-28803

Fine silver contacts should not be cleaned with knives, files, or abrasive paper or
cloth. Knives or files may leave scratches which increase arcing and deterioration
of the contacts. Abrasive paper or cloth may leave minute particles of insulating
abrasive material in the contacts and thus prevent closing.

The burnishing tool described above can be obtained from the factory.

RENEWAL PARTS

Sufficient quantities of renewal parts should be kept in stock for the prompt
replacement of any that are worn, broken or damaged.

When ordering renewal parts, address the nearest Sales Office of the General
Electric Company. Specify the name of the part wanted, quantity required, and
complete nameplate data, including the serial number, of the relay.

Since the last edition, changes have been made in Figures 3 and 14.

“.4”..
OPEN

3.0
CONTACT ADJUSTMENTS
NORMALLY OPEN CLOSED
UOSE WIPE 3/64-
3/64
GAP 3/64 3/64
a .5 TRAVEL 9/64 9/64

.1,

U.,
2.0
-4
0
>.
I.— I

‘I..
1.5
U.,
-I
)I._CLOSING TIME OF OPEN CONTACT
I-)
>-
0

1.0
OPENING TIME OF CLOSED CONTACT
r
. = =:
I..

.pi: S

I 1.5 2 3 4 5 6 7 8 910 20 30 40 50
TIMES PICK- UP

Figure 1 (0418A0711-1) Typical Time-Current Curves for the Contacts of Type PJC Relays

8
GCI-28803

MAKE DOTTED CONNECTIONS IF SHORTING BARS ARE REQUIRED


OPERATING COIL

2 6 8 10

SHORT FINGERS

Figure 2 (K—6209009—3) Internal Connections


for Type PJC11M and PJC12E Relays (Front View)

MAKE DOTTED CONNECTIONS IF SHORTING BARS ARE REQUIRED

— L
I

U

I
I R
I Z 3 02
1J±I
ITTT
I::— FROWT ViEW

3 5
0 S
a 6 10
* SHORT FICER

Figure 3 (K-6375600—4) Internal Connections


for Type PJC11AV and PJC12O Relays (Front View)

9
GEI—28803

Ii

a
2 6 10 _HCT
F NOEP

Figure 4 (K-6400236-1) Internal Connections for Type PJC11X Relay (Front View)
11

P[F?A FN(

NC
11

4 4 b

T
NCR
F I NC[

Figure 5 (K-6400331-3) Internal Connections


for Type PJC1IZ and PJC12R Relays (Front View)

10
GEI-28803

11 ‘3 15 19
. Q

TuN
MAKE IDITED CONI4ECTIS IF ORTIMG
LEFT

4 L 3

• =Offt FINGER
RIGHT

Figure 6 (K-6375604—8) Internal Connections


for Type PJC11AW, PJC12N and PJC12U Relays (Front View)

ic —SHoqr
F It[

Figure 7 (K-6154906-2) Internal Connections for Type PJC13E Relay (Front View)

11
GEI-28803

Lb L
15

• [Fr

H.C.

IONS
/LT_
IF SHORTING BARS ARE RtQuIiED

H.C.
V N-I
RIGHT

2 B
*.zS4ORT FINGER
Figure 8 (K—6375601-3) Internal Connections for Type PJC13H Relay (Front View)

MAKE DOTTED CONNECTIONS IF SHORTING BARS ARE REQUIRED

‘/H
DC PC
I LO EQ
DI RI
IL AL I
N I
I G
N I
G

1 7

2 4 10
*=SHOR NGEF?

Figure 9 (K-6375829.-2) Internal Connections for Type PJC13J Relay (Front View)

12
GEI-28803

I ILl
I
LJ
OP E RAT NC
Co IL

-tie

Figure 10 (K-6556533—1) Internal Connections for Type PJC14E Relay (Front View)
CODE NUMBERS
40 31 I 22 13 04

±J1± L
L
1 L ±
TTT TIFTT
±±±
TT T
FRONT VIEW

T L

N
G
-J

4 2 4 6 6 10
SHORT FNO[R

Figure 11 (K-640Q542-?) Internal Connections for Type PJC14C Relay (Front View)

13
GE 1-28803

11 13 15 17

U *

--J OPERATING CDI

. * L

2 4 6 8 10

Figure 12 (K-6305854-2) Internal Connections for Type PJC11AT Relay

14
GE 1-28803

PANEL LUCA1 ION


SEM I-FLUSH (2) 5/16--18 STUDS
FOR SURFAr,E MTG.

CUTOUT MAY REPLACE


DRILLED HOLES

PANEL DRILLING PANEL DRILLING


FOR SEMI-FLUSH MOUNTING FOR SURFACE MOUNTING
FRONT VIEW FRONT VIEW

3.0
TYPICAL DiM. 76MM
INCHES VIEW SHOWING ASSEMBLY OF HARDWARE
MM FOR SURFACE MTG. ON STEEL PANELS

Figure 13 (K—6209271-8) Outline and Panel Drilling Dimensions for Size Si Case

15
GE 1-28803

PANEL LOCATION
5/16—18 STUfl
SEMI -FLUSH 1 0-32 SURFACE MflJ
6. 625
168MM
1917 1513 H
00000
00000
20 18 16 14 12

10.312 -(4) 10—32 X 3/8


STUD
26 1MM MTCJ. SCREWS
NUMBERING
97531
GLASS 00000
00000
10 8 6 4 2
1.125 BACK VIEW
1/4 DRILL 29MM
4 HOLES CUTOUTS MAY REPLACE
6MM DRILLED HOLES

.218
5MM • 500
12MM
(TYPICAL )

PANEL DRILLING PANEL DRILLING


FLIP SEMI-FLUSH MOUNTING FOR SURFACE MOUNTING
FRONT VIEW FRONT VIEW

5/16—18 STUD
TYPICAL DIM.
INCHES VIEW
MM FOR

Figure 14 (K-6209272171) Outline and Panel Drilling Dimensions for Size S2 Case

16
GEI-28803

PANEL LOCATION
SEMI-FLUSH SURFACE 5/16—18 STUDS
6 625
. f-(4)
168MM FOR SURFACE MTG.

14.375
365MM
15 1P 6)1
384 MM STUD
.SREWS 1 0-32 NUMPER I NG
STUDS
97531
GLASS 00000
:i
00000
10 8 6 4 2
‘—‘-I
1. 125J
29MM
L_ .75j BACK VIEW
1/4 DRILL 19MM
6.187 3,0 CUTOUT MAY REPLACE
4 HOLES DRILLED HOLES
6MM 15 7MM ‘l76MM
5/8 DRILL 3.500
4 HOLES 8MM
15MM4
I-
7.406 4156
5.187 1 05MM
131MM 18 0MM
8 312’ ‘
PilMhHf
1 0 375
.
CUTIIUT 14.812
P63MM 6 906J 7.281
375MM 15Mjj 185MM
-- 468
37MM 4
I 7J
,
18
18MM 6MM
218 .500
5.25
5MM
687
5MM j 133MM 12MM
(TYPICAL)

144MM / 3/4 DRILL


PANE L 10 HOLES
PANEL DRILLING 19KM PANEL DRILLING
FOR SEMI-FLUSH MOUNTING FOR SURFACE MOUNTING
FRONT VIEW FRONT VIEW

CASE 5/16-18 STUD


TYPICAL DIM.
INCHES
1
VIEW SHOWING ASSEMPLY OF HARDWARE
MM FOR SURFACE MTG, ON STEEL PANELS

Figure 15 (K-6209213-5) Outline and Panel Drilling Dimensions for Size Ml Case

17
GEI-28803

PANEL LUAT I[r —(4) 5/16-18 STUDS


SEM I -FLUSH SURFACE 10-321 FOR SURFACE NTG.
6 625
168MM IS
19171513 11
00000
00000
20 18 16 14 12

STUD
6) l0—3 X 3/8 NUMBERING
MTG. SCREWS

97531
00000
tZZEZç 00000
10 8 6 4 2
125 BACK VIEW
CUTOUT MAY REPLACE
DRILLED HE1LE

PANEL DRILLING
FOR SURFACE MOUNTING
PANEL DRILLING FRONT VIF!
FOR SEMI-FLUSH MOUNTING
FRONT VIEW

TYPICAL DIN.
INCHES
MM

Figure 16 (K—6209274—6) Outline and Panel Drilling Dimensions for Size M2 Case

18
GE Power Management
215 Anderson Avenue
Markham, Ontario
Canada L6E 1B3
Tel: (905) 294-6222
Fax: (905) 201-2098
www.ge.comlindsyslpm

You might also like