Man Act GB Vec211r4

ACTIVE
Operating Instructions
Frequency Inverter 230 V / 400 V
0.55 kW ... 132.0 kW
General Information about the Documentation
The present documentation refers to the frequency inverters ACT 201 and ACT 401
series. With their factory settings, both series of devices are suited for a wide range of
applications. The modular hardware and software structure enables customer-specific
adaptation of the frequency inverters. Applications with high functionality and dynam-
ics requirements can be realized easily.
For better clarity, the documentation is structured according to the customer-specific

requirements made on the frequency inverter.
Quick Start Guide

The Quick Start Guide describes the basic steps required for mechanical and electrical
installation of the frequency inverter. The guided commissioning supports you in the
selection of necessary parameters and the configuration of the frequency inverter by
the software.
Operating Instructions
The Operating Instructions describe and document all functions of the frequency in-
verter. The parameters required for adapting the frequency inverter to specific appli-
cations as well as the wide range of additional functions are described in detail.
Application Manual
The application manual supplements the documentation for purposeful installation and
commissioning of the frequency inverter. Information on various subjects connected
with the use of the frequency inverter are described specific to the application.
Installation Instructions
Complementing the Quick Start Guide and the Operating Instructions, the Installation
Instructions provide information on how to install and use the additional/optional
components.
If you need a copy of the documentation or additional information, contact your local
representative of BONFIGLIOLI.
The following pictograms and signal words are used in the documentation:
Danger!
Danger refers to an immediate threat. Non-compliance with the precaution described
may result in death, serious injury or material damage.
Warning!
Warning refers to a possible threat. Non-compliance with the warning may result in
death, serious injury or material damage.
Caution!
Caution refers to an indirect threat. Non-compliance may result in personal or material
damage.
Attention!
Attention refers to a possible operational behavior or an undesired condition that can
occur in accordance with the reference text.
Note
Note and the related text provide useful information which supplements the corre-
sponding part of the documentation.
06/07 Operating Instructions ACTIVE 1

TABLE OF CONTENTS
1 General Safety Instructions and Information on Use .................................................... 8

1.1 General Information ...................................................................................... 8
1.2 Purpose of the Frequency Inverters .............................................................. 9
1.3 Transport and Storage ................................................................................... 9
1.4 Handling and Installation .............................................................................. 9
1.5 Electrical Connection ................................................................................... 10
1.6 Information on Use...................................................................................... 10
1.7 Maintenance and Service ............................................................................. 10
2 Scope of Supply............................................................................................................ 11
2.1 ACT 201 (up to 3.0 kW) and ACT 401 (up to 4.0 kW).................................. 11
2.2 ACT 201 (4.0 up to 9.2 kW) and ACT 401 (5.5 up to 15.0 kW).................... 12
2.3 ACT 401 (18.5 up to 30.0 kW) ..................................................................... 13
2.4 ACT 401 (37.0 up to 65.0 kW) ..................................................................... 14
2.5 ACT 401 (75.0 up to 132.0 kW) ................................................................... 15
3 Technical Data.............................................................................................................. 16
3.1 General technical data ................................................................................. 16
3.2 Technical data of control electronics ........................................................... 17
3.3 ACT 201 (0.55 up to 3.0 kW, 230 V) ............................................................ 18
3.4 ACT 201 (4.0 up to 9.2 kW, 230 V) .............................................................. 19
3.5 ACT 401 (0.55 up to 4.0 kW, 400 V) ............................................................ 20
3.6 ACT 401 (5.5 up to 15.0 kW, 400 V) ............................................................ 21
3.7 ACT 401 (18.5 up to 30.0 kW, 400 V) .......................................................... 22
3.8 ACT 401 (37.0 up to 65.0 kW, 400 V) .......................................................... 23
3.9 ACT 401 (75.0 up to 132.0 kW, 400 V) ........................................................ 24
3.10 Operation Diagrams..................................................................................... 25
4 Mechanical Installation................................................................................................ 26
4.1 ACT 201 (up to 3.0 kW) and ACT 401 (up to 4.0 KW).................................. 26
4.2 ACT 201 (4.0 up to 9.2 kW) and ACT 401 (5.5 up to 15.0 kW).................... 27
4.3 ACT 401 (18.5 up to 30.0 kW) ..................................................................... 28
4.4 ACT 401 (37.0 up to 65.0 kW) ..................................................................... 29
4.5 ACT 401 (75.0 up to 132.0 kW) ................................................................... 30
5 Electrical Installation ................................................................................................... 31

5.1 EMC Information.......................................................................................... 32
5.2 Block diagram .............................................................................................. 33
5.3 Optional Components .................................................................................. 34
5.4 Connection of the device ............................................................................. 35
5.4.1 Dimensioning of the conductor cross section ........................................................ 35
5.4.1.1 Typical conductor cross sections.......................................................................... 35
5.4.2 Mains Connection ............................................................................................... 36
2 Operating Instructions ACTIVE 06/07

5.4.3 Motor connection ............................................................................................... 37
5.4.3.1 Motor cable length, without filter ......................................................................... 37
5.4.3.2 Motor cable length, with output filter dU/dt .......................................................... 37
5.4.3.3 Motor cable length, with sine filter ....................................................................... 37
5.4.3.4 Group drive ....................................................................................................... 38
5.4.3.5 Speed sensor connection .................................................................................... 38
5.4.4 Connection of a Brake Resistor ............................................................................ 38
5.5 Connection of the construction sizes........................................................... 39
5.5.1 ACT 201 (up to 3.0 kW) and ACT 401 (up to 4.0 kW) ............................................ 39
5.5.2 ACT 201 (4.0 up to 9.2 kW) and ACT 401 (5.5 up to 15.0 kW) ............................... 41
5.5.3 ACT 401 (18.5 up to 30.0 kW)............................................................................. 43
5.5.4 ACT 401 (37.0 up to 65.0 kW)............................................................................. 45
5.5.5 ACT 401 (75.0 up to 132.0 kW) ........................................................................... 47
5.6 Control Terminals ........................................................................................ 49
5.6.1 Relay Output ..................................................................................................... 50
5.6.2 Control Terminals – Terminal Diagram ................................................................. 51
5.6.2.1 Configuration 110 – Sensorless Control ................................................................ 51
5.6.2.2 Configuration 111 – Sensorless Control with Technology Controller......................... 52
5.6.2.3 Configuration 410 – Sensorless Field-Oriented Control........................................... 52
5.6.2.4 Configuration 411 – Sensorless Field-Oriented Control with Technology Controller ... 53
5.6.2.5 Configuration 430 – Sensorless Field-Oriented Control, speed or torque controlled... 53
5.6.2.6 Configuration 210 – Field-Oriented Control, speed controlled ................................. 54
5.6.2.7 Configuration 211 – Field-Oriented Control, with Technology Controller .................. 54
5.6.2.8 Configuration 230 – Field-Oriented Control, speed and torque controlled................. 55
6 Control Unit KP500 ...................................................................................................... 56

6.1 Menu Structure ............................................................................................ 57
6.2 Main Menu ................................................................................................... 57
6.3 Actual Value Menu (VAL) ............................................................................. 58
6.4 Parameter Menu (PARA).............................................................................. 59
6.5 Copy Menu (CPY) ......................................................................................... 60
6.5.1 Reading the Stored Information........................................................................... 60
6.5.2 Menu Structure .................................................................................................. 61
6.5.3 Selecting the Source........................................................................................... 61
6.5.4 Selecting the Destination .................................................................................... 62
6.5.5 Copy Operation .................................................................................................. 62
6.5.6 Error Messages .................................................................................................. 63
6.6 Read data from the KP 500 control unit ...................................................... 64
6.6.1 Activating .......................................................................................................... 64
6.6.2 Transfer data..................................................................................................... 65
6.6.3 Reset to Normal Mode ........................................................................................ 66
6.7 Control Menu (CTRL) ................................................................................... 66
6.8 Controlling the Motor via the Control Unit .................................................. 67
7 Commissioning of the Frequency Inverter................................................................... 70

7.1 Switching on Mains Voltage......................................................................... 70
7.2 Setup Using the Control Unit ....................................................................... 70
7.2.1 Configuration ..................................................................................................... 71
7.2.2 Data Set............................................................................................................ 72
7.2.3 Motor Type........................................................................................................ 72
7.2.4 Machine Data..................................................................................................... 73
7.2.5 Plausibility check ................................................................................................ 74
7.2.6 Parameter identification ...................................................................................... 75

7.2.7 Application data ................................................................................................. 77
7.2.7.1 Acceleration and deceleration.............................................................................. 77
7.2.7.2 Set points at multi-functional input ...................................................................... 78
7.2.7.3 Selection of an actual value for display................................................................. 78
7.3 Check direction of rotation .......................................................................... 79
7.4 Speed sensor................................................................................................ 80
7.4.1 Speed sensor 1 .................................................................................................. 80
7.4.2 Speed sensor 2 .................................................................................................. 81
7.5 Set-up via the Communication Interface .................................................... 82
8 Inverter Data ............................................................................................................... 84

8.1 Serial Number .............................................................................................. 84
8.2 Optional Modules ......................................................................................... 84
8.3 Inverter Software Version ........................................................................... 84
8.4 Set Password ............................................................................................... 84
8.5 Control Level ................................................................................................ 85
8.6 User Name.................................................................................................... 85
8.7 Configuration ............................................................................................... 85
8.8 Language ..................................................................................................... 88
8.9 Programming ............................................................................................... 88
9 Machine Data ............................................................................................................... 89

9.1 Rated Motor Parameters.............................................................................. 89
9.2 Further motor parameters ........................................................................... 90
9.2.1 Stator Resistance ............................................................................................... 90
9.2.2 Leakage Coefficient ............................................................................................ 90
9.2.3 Magnetizing Current ........................................................................................... 91
9.2.4 Rated Slip Correction Factor ................................................................................ 91
9.3 Internal values............................................................................................. 92
9.4 Speed sensor 1............................................................................................. 92
9.4.1 Operation mode speed sensor 1 .......................................................................... 92
9.4.2 Division marks, speed sensor 1............................................................................ 93
10 System Data ................................................................................................................. 94

10.1 Actual Value System .................................................................................... 94
10.2 Volume Flow and Pressure .......................................................................... 94
11 Operational Behavior ................................................................................................... 95

11.1 Starting Behavior ......................................................................................... 95
11.1.1 Starting Behavior of Sensorless Control System..................................................... 95
11.1.1.1 Starting Current ................................................................................................. 97
11.1.1.2 Frequency Limit ................................................................................................. 97
11.1.2 Flux Formation................................................................................................... 97
11.2 Stopping Behavior........................................................................................ 98
11.2.1 Switch-Off Threshold ........................................................................................ 100
11.2.2 Holding Time ................................................................................................... 100
11.3 Direct current brake................................................................................... 100
11.4 Auto Start................................................................................................... 101
11.5 Search Run................................................................................................. 102

11.6 Positioning ................................................................................................. 103
11.6.1 Reference Positioning ....................................................................................... 104
11.6.2 Axis Positioning............................................................................................. 10712
Error and warning behavior............................................................................... 109
12.1 Overload Ixt ............................................................................................... 109
12.2 Temperature .............................................................................................. 109
12.3 Controller Status........................................................................................ 110
12.4 IDC Compensation Limit ............................................................................ 110
12.5 Frequency Switch-Off Limit ....................................................................... 110
12.6 Motor Temperature.................................................................................... 111
12.7 Phase Failure ............................................................................................. 111
12.8 Automatic Error Acknowledgment............................................................. 112
13 Reference Values........................................................................................................ 113

13.1 Frequency Limits........................................................................................ 113
13.2 Slip Frequency ........................................................................................... 113
13.3 Percentage Value Limits ............................................................................ 113
13.4 Frequency Reference Channel ................................................................... 114
13.4.1 Block Diagram ................................................................................................. 115
13.5 Reference Percentage Channel.................................................................. 117
13.5.1 Block Diagram ................................................................................................. 117
13.6 Fixed Reference Values.............................................................................. 119
13.6.1 Fixed Frequencies ............................................................................................ 119
13.6.2 JOG-Frequency ................................................................................................ 119
13.6.3 Fixed Percentages ............................................................................................ 120
13.7 Frequency ramps ....................................................................................... 120
13.8 Percentage Value Ramps ........................................................................... 123
13.9 Block Frequencies ...................................................................................... 123
13.10 Motor Potentiometer ................................................................................. 124
13.10.1 Motorpoti (MP)................................................................................................. 125
13.10.2 Motorpoti (KP) ................................................................................................. 125
13.10.3 Controlling the Motor via the Control Unit........................................................... 126
13.11 Repetition frequency input ........................................................................ 127
14 Control Inputs and Outputs ....................................................................................... 128

14.1 Multi-function input MFI1.......................................................................... 128
14.1.1 Analog Input MFI1A ......................................................................................... 128
14.1.1.1 Characteristic................................................................................................... 128
14.1.1.2 Scaling ............................................................................................................ 130
14.1.1.3 Tolerance Band and Hysteresis.......................................................................... 130
14.1.1.4 Filter Time Constant ......................................................................................... 131
14.1.1.5 Error and warning behavior............................................................................... 132
14.2 Multi-function output MFO1 ...................................................................... 132
14.2.1 Analog Output MFO1A ...................................................................................... 133
14.2.1.1 Output Characteristic........................................................................................ 133
14.2.2 Frequency Output MFO1F ................................................................................. 134
14.2.2.1 Scaling ............................................................................................................ 134
14.3 Digital Outputs........................................................................................... 135
14.3.1 Setting Frequency ............................................................................................ 136
14.3.2 Reference value reached................................................................................... 136
14.3.3 Flux Formation Ended....................................................................................... 137
14.3.4 Open brake ..................................................................................................... 137
14.3.5 Current Limitation ............................................................................................ 137
14.3.6 External Fan .................................................................................................... 137
14.3.7 Warning Mask .................................................................................................. 138
14.4 Digital Inputs ............................................................................................. 140
14.4.1 Start command ................................................................................................ 143
14.4.2 3-Wire-Control ................................................................................................. 143
14.4.3 Error Acknowledgment ..................................................................................... 144
14.4.4 Timer .............................................................................................................. 144
14.4.5 Thermo-contact ............................................................................................... 144
14.4.6 n-/M-Control Change-Over ................................................................................ 144
14.4.7 Data Set Change-Over ...................................................................................... 145
14.4.8 Fixed Value Change-Over.................................................................................. 146
14.4.9 Motor Potentiometer......................................................................................... 147
14.5 Function Modules....................................................................................... 147
14.5.1 Timer .............................................................................................................. 147
14.5.1.1 Time Constant ................................................................................................. 148
14.5.2 Comparator ..................................................................................................... 150
14.5.3 Logic Modules .................................................................................................. 151
15 V/f - Characteristic..................................................................................................... 156

15.1 Dynamic Voltage Pre-Control .................................................................... 157
16 Control Functions ....................................................................................................... 158

16.1 Intelligent current limits ........................................................................... 158
16.2 Voltage controller ...................................................................................... 159
16.3 Technology Controller................................................................................ 163
16.4 Functions of Sensorless Control ................................................................ 171
16.4.1 Slip compensation ............................................................................................ 171
16.4.2 Current limit value controller ............................................................................. 171
16.5 Functions of Field-Orientated Control ....................................................... 172
16.5.1 Current Controller ............................................................................................ 172
16.5.2 Torque Controller ............................................................................................. 174
16.5.2.1 Limit Value Sources .......................................................................................... 174
16.5.3 Speed controller............................................................................................... 175
16.5.3.1 Limitation of Speed Controller ........................................................................... 177
16.5.3.2 Limit Value Sources .......................................................................................... 178
16.5.4 Acceleration Pre-Control ................................................................................... 178
16.5.5 Field Controller ................................................................................................ 179
16.5.5.1 Limitation of field controller............................................................................... 180
16.5.6 Modulation Controller ....................................................................................... 180
16.5.6.1 Limitation of Modulation Controller .................................................................... 181
17 Special Functions ....................................................................................................... 182

17.1 Pulse Width Modulation............................................................................. 182
17.2 Fan ............................................................................................................. 183
17.3 Bus controller............................................................................................. 183
17.4 Brake Chopper and Brake Resistance........................................................ 185
17.4.1 Dimensioning of Brake Resistor ......................................................................... 186
17.5 Motor Circuit Breaker................................................................................. 187
17.6 V-belt Monitoring....................................................................................... 188

17.7 Functions of Field-Orientated Control ....................................................... 189
17.7.1 Motor Chopper................................................................................................. 189
17.7.2 Temperature Adjustment .................................................................................. 190
17.7.3 Encoder Monitoring .......................................................................................... 191
18 Actual Values.............................................................................................................. 192

18.1 Actual Values of the Frequency Inverter ................................................... 192
18.2 Actual Values of the Machine..................................................................... 193
18.3 Actual Value Memory ................................................................................. 194
18.4 Actual Values of the System ...................................................................... 195
18.4.1 Actual Value System ......................................................................................... 195
18.4.2 Volume Flow and Pressure ................................................................................ 196
19 Error Protocol ............................................................................................................. 197

19.1 Error List .................................................................................................... 197
19.1.1 Error Messages ................................................................................................ 197
19.2 Error Environment ..................................................................................... 199
20 Operational and Error Diagnosis ................................................................................ 201

20.1 Status Display ............................................................................................ 201
20.2 Status of Digital Signals............................................................................. 201
20.3 Controller Status........................................................................................ 202
20.4 Warning Status .......................................................................................... 203
21 Parameter List............................................................................................................ 204

21.1 Actual Value Menu (VAL) ........................................................................... 204
21.2 Parameter Menu (PARA)............................................................................ 207

1 General Safety Instructions and Information on Use
Warning! The specifications and instructions contained in the documentation must
be complied with strictly during installation and commissioning. Only
qualified staff who has read the documentation and, in particular, the
safety instructions carefully is allowed to carry out installation or com-
missioning work or to operate the frequency inverters. The term „Quali-
fied Staff“ refers to anybody who is familiar with the installation, assem-
bly, commissioning and operation of the frequency inverter and has the
proper qualification for the job.
The present documentation was prepared with great care and it was subjected to
extensive and repeated reviews. For reasons of clarity, it was not possible to include
all details of all types of the product in the documentation. Neither was it possible to
consider all conceivable installation, operation or maintenance situations. If you re-
quire further information or if you meet with specific problems which are not dealt
with in sufficient detail in the documentation, contact your local BONFIGLIOLI agent.
We would also like to point out that the contents of this documentation do not form
part of any previous or existing agreement, assurance or legal relationship. Neither
are they intended to supplement or replace such agreements, assurances or legal
relationships. The manufacturer's obligations are exclusively specified in the relevant
purchase contract. This contract also contains all and any warranty regulations which
may apply to the relevant scope of supply. These contractual warranty provisions are
neither extended nor limited by the specifications contained in this documentation.
The manufacturer reserves the right to correct or amend the specifications, product
information and omissions in these operating instructions without notice. The manu-
facturer shall not be liable for any damage, injuries or costs which may be caused by
the aforementioned reasons.
1.1 General Information

Warning! The DC-link circuit of the frequency inverter is charged during operation,
i.e. there is always the risk of contact with high voltage. Frequency in-
verters are used for driving moving parts and they may become hot at
the surface during operation.
Any unauthorized removal of the necessary covers, improper use, wrong
installation or operation may result in serious injuries or material dam-
age.
In order to avoid such injuries or damage, only qualified staff may carry
out the transport, installation, setup or maintenance work required. The
standards EN 50178, IEC 60364 (Cenelec HD 384 or DIN VDE 0100), IEC
60664-1 (Cenelec HD 625 or VDE 0110-1), BGV A2 (VBG 4) as well as
the applicable national regulations must be complied with. The term
„Qualified Staff“ refers to anybody who is familiar with the installation,
assembly, commissioning and operation of the frequency inverter as well
as the possible hazards and has the proper qualification for the job.

1.2 Purpose of the Frequency Inverters
Warning! The frequency inverters are electrical drive components intended for
installation in industrial plants or machines. Commissioning and start of
operation is not allowed until it has been verified that the machine
meets the requirements of the EC Machinery Directive 98/37/EEC and
EN 60204. In accordance with the CE marking requirements, the fre-
quency inverters also comply with the Low Voltage Directive 72/23/EEC
as well as EN 50178 / DIN VDE 0160 and EN 61800-2. The user shall be
responsible for making sure that the requirements of the EMC Directive
89/336/EEC are met. Frequency inverters are only available at special-
ized dealers and are exclusively intended for professional use as per
EN 61000-3-2.
The frequency inverters are also marked with the UL label according to
UL508c, which proves that they also meet the requirements of the
CSA Standard C22.2-No. 14-95.
The technical data, connection specifications and information on ambi-
ent conditions are indicated on the name plate and in the documentation
and must be complied with in any case. Anyone involved in any kind of
work at the device must have read the instructions carefully and under-
stood them before starting the work.
1.3 Transport and Storage

The frequency inverters must be transported and stored in an appropriate way. Dur-
ing transport and storage the devices must remain in their original packaging. The
units may only be stored in dry rooms which are protected against dust and moisture
and are exposed to little temperature deviations only. Observe the climatic conditions
according to EN 50178 and the marking on the packaging. The frequency inverters
must not be stored for more than one year without connecting them to nominal volt-
age.
1.4 Handling and Installation

Warning! Damaged or destroyed components must not be put into operation be-
cause they may be a health hazard.
The frequency inverters are to be used in accordance with the documentation as well
as the applicable directives and standards. They must be handled carefully and pro-
tected against mechanical stress. Do not bend any components or change the isolat-
ing distances. Do not touch any electronic components or contacts. The devices are
equipped with components which are sensitive to electrostatic energy and can easily
be damaged if handled improperly. Any use of damaged or destroyed components
shall be considered as a non-compliance with the applicable standards. Do not re-
move any warning signs from the device.
06/07 06/07 Operating Instructions

Operating ACTIVE
Instructions ACTIVE 9 9
1.5 Electrical Connection
Warning! Before any assembly or connection work, discharge the frequency in-
verter. Verify that the frequency inverter is discharged.
Do not touch the terminals because the capacitors may still be charged.
Comply with the information given in the operating instructions and on
the frequency inverter label.
When working at the frequency inverters, comply with the applicable standards BGV
A2 (VBG 4), VDE 0100 and other national directives. Comply with the electrical instal-
lation instructions given in the documentation as well as the relevant directives. The
manufacturer of the industrial machine or plant is responsible for making sure that
the limit values specified in the EMC product standard EN 61800-3 for electrical vari-
able-speed drives are complied with. The documentation contains information on
EMC-conforming installation. The cables connected to the frequency inverters may
not be subjected to high-voltage insulation tests unless appropriate circuitry meas-
ures are taken before. Otherwise the unit may be damaged.
1.6 Information on Use

Warning! The frequency inverter may be connected to power supply every 60 s.
Consider this for a jog operation of a mains contactor. For commission-
ing or after an emergency stop, a non-recurrent, direct restart is permis-
sible.
After a failure and restoration of the power supply, the motor may start
unexpectedly if the AutoStart function is activated. Install protective
equipment if personal injury or material damage is possible.
Before commissioning and start of normal operation, make sure to fix all
covers and check all terminals. Check the additional monitoring and
protective devices according to EN 60204 and applicable the safety di-
rectives (e.g. Working Machines Act, Accident Prevention Directives
etc.).
No connection work may be performed, while the system is in operation.
1.7 Maintenance and Service

Warning! Unauthorized opening and improper interventions can lead to personal
injury or material damage. Repairs on the frequency inverters may only
be carried out by the manufacturer or persons authorized by the manu-
facturer. Check protective equipment regularly.
10 10 Operating Instructions
Operating ACTIVE
Instructions ACTIVE 06/07 06/07
2 Scope of Supply
Thanks to the modular hardware components, the frequency inverters can be inte-
grated in the automation concept easily. The scope of delivery described can be sup-
plemented by optional components and adapted to the customer-specific require-
ments. The plug-in type connection terminals enable a safe function and an economi-
cal assembly.
2.1 ACT 201 (up to 3.0 kW) and ACT 401 (up to 4.0 kW)
Scope of Supply
Scope of Supply
A Frequency inverter
B Terminal strip X1 (Phoenix ZEC 1,5/ST7,5)
Plug-in terminals for mains connection and DC linking
C Terminal strip X10 (Phoenix ZEC 1.5/3ST5.0)
Plug-in terminals for the relay output
D Standard fixtures for vertical assembly
E Brief Instructions and manuals on CD
F Terminal strip X2 (Phoenix ZEC 1,5/ST7,5)
Plug-in terminal for brake resistor and motor connection
G Control terminals X210A / X210B (Wieland DST85 / RM3.5)
Plug-in terminal for connection of the control signals
Note: Please check incoming goods for quality, quantity and nature without
delay. Obvious defects such as exterior damage of the packing and/or
the unit must be notified to the sender within seven days for insurance
reasons.
06/07 06/07 Operating

Operating Instructions ACTIVE
2.2 ACT 201 (4.0 up to 9.2 kW) and ACT 401 (5.5 up to
15.0 kW)
Scope of Supply
Scope of Supply
B Terminal strip X10 (Phoenix ZEC 1.5/3ST5.0)
C Standard fixtures with fixing screws (M4x20, M4x60)
for vertical assembly
D Brief Instructions and manuals on CD
E Control terminals X210A / X210B (Wieland DST85 / RM3.5)
delay. Obvious defects such as exterior damage of the packing and/or the
unit must be notified to the sender within seven days for insurance rea-
sons.
12 12 Operating
2.3 ACT 401 (18.5 up to 30.0 kW)
Scope of Supply
Scope of Supply
C Standard fixtures with fixing screws (M4x20, M4x70)
sons.

2.4 ACT 401 (37.0 up to 65.0 kW)
Scope of Supply
Scope of Supply
C Standard fixtures with fixing screws (M5x20)
sons.
14 14 Operating
2.5 ACT 401 (75.0 up to 132.0 kW)
Scope of Supply
Scope of Supply
C Control terminals X210A / X210B (Wieland DST85 / RM3.5)
sons.

3 Technical Data
3.1 General technical data
CE conformity The frequency inverters ACT meet the requirements of the low-voltage directive
73/23/EEC and the requirements of the standards EN 50178 and EN 61800-2.
EMC directive For proper installation of the frequency inverter in accordance with the standard
EN 61800-3 comply with the installation instructions in this operation manual.
Interference The frequency inverters meet the requirements of the standard EN 61800-3 for
immunity factor operation in industrial environment.
UL approval The frequency inverters are marked with the UL label according to UL508c, which
proves that they also meet the requirements of the CSA Standard C22.2-No. 14-
95.
Ambient Operation: 0 … 55 °C; for exceeding 40 °C comply with the derating.

temperature
Climate class Operation: 3K3 (EN60721-3-3)

Relative air humidity 15 ... 85 %, not condensing
Degree IP20 on the condition of proper installation of the covers and terminals.
of protection
Mounting altitude Up to 1000 m at rated operating conditions.

Up to 4000 m with derating.
Storage According to EN 50178;

BONFIGLIOLI VECTRON recommends the connection of the device to mains volt-
age for 60 minutes latest after one year of storage.
Functions Appropriate control behaviours (configurations) adapted for motors and applica-
tions
− Speed-/torque control switch-over
− Various protective functions for motor and frequency inverter
− Positioning absolute or relative to a reference point
− Synchronization to a rotating drive
− Special brake control and load detection for hoist drives
− S-ramps for jerk limitation at acceleration and deceleration
− Technology- (PI) controller
− Parameterization of master-slave operation via system bus
− Error protocol
− Simplified and enhanced operation via PC (commissioning, parameterization,
record back-up, diagnosis with scope)
Parameterization − Freely programmable digital inputs and outputs

− Various modules for logical operations and signal processing
− Four discrete records including motor parameters
16 16 Operating
3.2 Technical data of control electronics
Control terminal X210A Control terminal X210B

X210A.1 DC 20 V output (Imax=180 mA) X210B.1 Digital input 1)
X210A.2 Ground 20 V/ Ground 24 V (ext.) X210B.2 GND
X210A.3 Digital input Controller Release X210B.3 Digital output 1)
X210A.4 Digital inputs 1) X210B.4 Multi-function output 1) (voltage
signal proportional actual frequency
value, factory setting)
X210A.5 X210B.5 Supply voltage DC 10 V for refer-
ence value potentiometer,
(Imax=4 mA)
X210A.6 X210B.6 Multi-function input 1) (Reference
speed 0 … +10 V, factory setting)
X210A.7 X210B.7 Ground 10 V
Relay output X10

S3OUT.1 Monitoring function (factory setting)
1)
The control terminals are freely configurable.
Note:
The various configurations set the control terminals to defined adjustments. These adjustments can
be adapted to user-specific applications and various functions can be assigned to the freely pro-
grammable control terminals.
Technical data of the control terminals

Digital inputs (X210A.3…X210B.1): Low Signal: DC 0…3 V, High Signal: DC 12…30 V,
Input resistance: 2.3 kΩ, response time: 16 ms, PLC compatible
X210A.6 and X210A.7 additional: frequency signal: DC 0 V...30 V, 10 mA at DC 24 V, fmax=150 kHz
Digital output (X210B.3): Low Signal: DC 0…3 V, High Signal: DC 12…30 V,
maximum output current: 40 mA, PLC compatible
Multi-function output (X210B.4):
analog signal: DC 24 V, maximum output current: 40 mA, pulse-width modulated (fPWM= 116 Hz),
digital signal: Low Signal: DC 0…3 V, High Signal: DC 12…30 V, output current: 40 mA, PLC compati-
ble,
frequency signal: output voltage: DC 0…24 V, maximum output current: 40 mA,
maximum output frequency: 150 kHz
Multi-function input (X210B.6):
analog signal: input voltage: DC 0… 10 V (Ri=70 kΩ), input current: DC 0…20 mA (Ri=500 Ω),
digital signal: Low Signal: DC 0…3 V, High Signal: DC 12 V…30 V, response time: 16 ms, PLC com-
patible
Conductor cross section:
The terminals are suitable for the conductor cross sections:
with wire end ferrule: 0.25…1.0 mm²
without wire end ferrule: 0.14…1.5 mm²

3.3 ACT 201 (0.55 up to 3.0 kW, 230 V)
Type
ACT 201 -05 -07 -09 -11 -13 -15
Output motor side
Recommended shaft output P kW 0.55 0.75 1.1 1.5 2.2 3.0 4)
Output current I A 3.0 4.0 5.4 5) 7.0 9.5 12.5 4) 5)
Long-term overload current (60 s) I A 4.5 6.0 7.3 10.5 14.3 16.2
Short-term overload current (1 s) I A 6.0 8.0 8.0 14.0 19.0 19.0
Output voltage U V Maximum up to mains voltage, three-phase
Protection - - Short circuit / earth fault proof
Rotary field frequency f Hz 0 ... 1000, depending on switching frequency
Switching frequency f kHz 2. 4. 8. 12. 16
Output brake resistor
min. brake resistor R Ω 100 100 100 37 37 37
Recommended brake resistor
R Ω 230 160 115 75 55 37
(UdBC = 385 V)
Input, mains side
Mains current 3) , 3ph/PE 3 4 5.5 1) 7 9.5 10.5 1)
I A
1ph/N/PE; 2ph/PE 5.4 7.2 9.5 2) 13.2 16.5 2) 16.5 2) 4) 7)
Mains voltage U V 184 ... 264
Mains frequency f Hz 45 ... 66
Fuse 3ph/PE 6 10 16 16
I A
1ph/N/PE; 2ph/PE 10 16 20 20
UL Type 250 VAC RK5, 3ph/PE 6 10 15 15
I A
1ph/N/PE; 2ph/PE 10 15 20 20
Mechanics
Dimensions HxWxD mm 190x60x175 250x60x175
Weight (approx.) m kg 1.2 1.6
Degree of protection - - IP20 (EN60529)
Terminals A mm2 0.2 ... 1.5
Form of assembly - - vertical
Ambient conditions
Energy dissipation
P W 43 53 73 84 115 170
(2 kHz switching frequency)
Coolant temperature Tn °C 0 ... 40 (3K3 DIN IEC 721-3-3)
Storage temperature TL °C -25 ... 55
Transport temperature TT °C -25 ... 70
Rel. air humidity - % 15 ... 85; not condensing
If required by the customer, the switching frequency may be increased if the output current is reduced at the
same time. Comply with the applicable standards and regulations for this operating point.
Output current 6)
Switching frequency
Frequency inverter nominal power
2 kHz 4 kHz 8 kHz 12 kHz 16 kHz
0.55 kW 3.0 A 3.0 A 3.0 A 2.5 A 2.0 A
0.75 kW 4.0 A 4.0 A 4.0 A 3.4 A 2.7 A
1.1 kW 5.4 A 2) 5.4 A 2) 5) 5.4 A 2) 5) 4.5 A 2) 5) 3.7 A 5)
1.5 kW 7.0 A 7.0 A 7.0 A 5.9 A 4.8 A
2.2 kW 9.5 A 2) 9.5 A 2) 9.5 A 2) 8.0 A 2) 6.5 A
3.0 kW 2) 4) 12.5 A 1) 12.5 A 1) 5)
12.5 A 1) 5)
10.5 A 1) 5) 8.5 A 5)
1)
Three-phase connection requires a commutating choke.
2)
One- and two-phase connection requires a commutating choke.
3)
Mains current with relative mains impedance ≥ 1% (see chapter„Electrical installation“)
4)
Maximum output current is 9.5 A for one- and two-phase connection.
5)
Switching frequency is reduced in thermal limit range
6)
Maximum current in continuous operation
7)
The device for one-phase connection is not included in the product catalogue. It is available on demand.
18 18 Operating
3.4 ACT 201 (4.0 up to 9.2 kW, 230 V)
Type
ACT 201 -18 -19 -21 -22
Output motor side
Recommended shaft output P kW 4.0 5.5 7.5 4) 9.2
Output current I A 18.0 22.0 32.0 35.0
Long-term overload current (60 s) I A 26.3 30.3 44.5 51.5
Short-term overload current (1 s) I A 33.0 33.0 64.0 64.0
Rotary field frequency f Hz 0 ... 1000, depending on switching frequency
Switching frequency f kHz 2, 4, 8, 12, 16
min. brake resistor R Ω 24 24 12 12
R Ω 30 24 16 12
(UdBC = 385 V)
Input, mains side
Mains current 3), 3ph/PE 18 20 1) 28.2 1) 35.6 1)
I A
1ph/N/PE; 2ph/PE 28 2) 7) - 4) - 4) - 4)
Fuse 3ph/PE 25 25 35 50
I A 4)
1ph/N/PE; 2ph/PE 35 - - 4) - 4)
UL Type 250 VAC RK5, 3ph/PE 20 25 30 40
I A
1ph/N/PE; 2ph/PE
Mechanics
Terminals A mm2 0.2 … 6 0.2 … 16
Ambient conditions
Energy dissipation
P W 200 225 310 420
(2 kHz switching frequency)
Output current 6)
Switching frequency
4.0 kW 18.0 A 2) 18.0 A 2) 18.0 A 2) 15.1 A 2) 12.2 A
4)
5.5 kW 23.0 A 1) 22.7 A 1). 5) 22.0 A 1), 5) 18.5 A 5) 15.0 A 5)
4)
7.5 kW 32.0 A 1) 32.0 A 1) 32.0 A 1) 26.9 A 1) 21.8 A
4)
9.2 kW 40.0 A 1) 38.3 A 1), 5) 35.0 A 1), 5) 29.4 A 1), 5) 23.8 A 5)
1)
2)
One- and two-phase connection requires a commutating choke.
3)
4)
Only three-phase connection
5)
Switching frequency is reduced in thermal limit range.
6)
7)
The device for one-phase connection is not included in the product catalogue. It is available on demand.

3.5 ACT 401 (0.55 up to 4.0 kW, 400 V)
Type
ACT 401 -05 -07 -09 -11 -12 -13 -15 -18
Output motor side
Recommended shaft output P kW 0.55 0.75 1.1 1.5 1.85 2.2 3.0 4.0
Output current I A 1.8 2.4 3.2 3.8 3) 4.2 5.8 7.8 9.0 3)
Long-term overload current (60 s) I A 2.7 3.6 4.8 5.7 6.3 8.7 11.7 13.5
Short-term overload current (1 s) I A 3.6 4.8 6.4 7.6 8.4 11.6 15.6 18.0
Rotary filed frequency f Hz 0 ... 1000, depending on switching frequency
min. brake resistor R Ω 300 300 300 300 136 136 136 92
R Ω 930 634 462 300 300 220 148 106
(UdBC = 770 V)
Input, mains side
1)
Mains current 2) 3ph/PE I A 1.8 2.4 2.8 3.3 1) 4.2 5.8 6.8 1)
7.8 1)

Fuse 3ph/PE I A 6 10
UL-Type 600 VAC RK5. 3ph/PE I A 6 10
Mechanics
Terminals A mm2 0.2 ... 1.5
Ambient conditions
Energy dissipation
P W 40 46 58 68 68 87 115 130
(2 kHz Switching frequency)
Output current 4)
Switching frequency
0.55 kW 1.8 A 1.8 A 1.8 A 1.5 A 1.2 A
0.75 kW 2.4 A 2.4 A 2.4 A 2.0 A 1.6 A
1.1 kW 3.2 A 1) 3.2 A 1) 3.2 A 1) 2.7 A 1) 2.2 A
1.5 kW 1) 3.8 A 3.8 A 3) 3.8 A 3) 3.2 A 3) 2.6 A 3)
1.85 kW 4.2 A 4.2 A 4.2 A 3.5 A 2.9 A
2.2 kW 5.8 A 5.8 A 5.8 A 4.9 A 3.9 A
3.0 kW 7.8 A 1) 7.8 A 1) 7.8 A 1) 6.6 A 1) 5.3 A
4.0 kW 9.0 A 1) 9.0 A 1) 3) 9.0 A 1) 3) 7.6 A 1) 3) 6.1 A 3)
1)
2)
3)
4)
20 20 Operating
3.6 ACT 401 (5.5 up to 15.0 kW, 400 V)
Type
ACT 401 -19 -21 -22 -23 -25
Output. motor side
Recommended shaft output P kW 5.5 7.5 9.2 11.0 15.0
Output current I A 14.0 18.0 22.0 3) 25.0 32.0
Long-term overload current (60 s) I A 21.0 26.3 30.3 37.5 44.5
Short-term overload current (1 s) I A 28.0 33.0 33.0 50.0 64.0
min. brake resistor R Ω 48 48 48 32 32
R Ω 80 58 48 48 32
(UdBC = 770 V)
Input, mains side
1)
Mains current 2) 3ph/PE I A 14.2 15.8 20.0 1) 26.0 28.2 1)

Fuse 3ph/PE I A 16 25 35
UL-Type 600 VAC RK5. 3ph/PE I A 20 30 40
Mechanics
Terminals A mm2 0.2 ... 6 0.2 ... 16
Ambient conditions
Energy dissipation
P W 145 200 225 240 310
Output current
Switching frequency
5.5 kW 14.0 A 14.0 A 14.0 A 11.8 A 9.5 A
7.5 kW 18.0 A 1) 18.0 A 1) 18.0 A 1) 15.1 A 1) 12.2 A
9.2 kW 1)
23.0 A 22.7 A 3) 22.0 A 3) 18.5 A 3) 15.0 A 3)
11 kW 25.0 A 25.0 A 25.0 A 21.0 A 17.0 A
15 kW 32.0 A 1) 32.0 A 1) 32.0 A 1) 26.9 A 1) 21.8 A
1)
2)
3)
4)

3.7 ACT 401 (18.5 up to 30.0 kW, 400 V)
Type
ACT 401 -27 -29 -31
Output. motor side
Recommended shaft output P kW 18.5 22.0 30.0
Output current I A 40.0 45.0 60.0
Long-term overload current (60 s) I A 60.0 67.5 90.0
Short-term overload current (1 s) I A 80.0 90.0 120.0
Switching frequency f kHz 2, 4, 8
min. brake resistor R Ω 16
R Ω 26 22 16
(UdBC = 770 V)
Input, mains side
1)
Mains current 2) 3ph/PE I A 42.0 50.0 58.0
Fuse 3ph/PE I A 50 63
UL-Type 600 VAC RK5. 3ph/PE I A 50 60
Mechanics
Dimensions HxWxD mm 250x200x260
Weight (approx.) m kg 8
Terminals A mm2 up to 25
Ambient conditions
Energy dissipation
P W 445 535 605
Output current 3)
Switching frequency
2 kHz 4 kHz 8 kHz
18.5 kW 40.0 A 40.0 A 40.0 A
22 kW 45.0 A 45.0 A 45.0 A
30 kW 60.0 A 1) 60.0 A 1) 60.0 A 1)
1)
2)
3)
22 22 Operating
3.8 ACT 401 (37.0 up to 65.0 kW, 400 V)
Type
ACT 401 -33 -35 -37 -39
Output. motor side
Recommended shaft output P kW 37.0 45.0 55.0 65.0
Switching frequency f kHz 2. 4. 8
Output brake resistor 5)
min. brake resistor R Ω 7.5
R Ω 13 11 9 7.5
(UdBC = 770 V)
Input, mains side
Mains current 2) 3ph/PE I A 87.0 104.0 105.0 1) 120.0 1)

Fuse 3ph/PE I A 100 125 125 125
UL-Type 600 VAC RK5. 3ph/PE I A 100 125 125 125
Mechanics
Weight (approx.) m kg 20
Terminals A mm2 up to 70
Form of assembly - - Vertical
Ambient conditions
Energy dissipation
P W 665 830 1080 1255
Output current 4)
Switching frequency
2 kHz 4 kHz 8 kHz
37 kW 75.0 A 75.0 A 75.0 A
45 kW 90.0 A 90.0 A 90.0 A
55 kW 110.0 A 1) 110.0 A 1) 110.0 A 1)
65 kW 125.0 A 1), 3) 125.0 A 1), 3) 125.0 A 1), 3)
1)
2)
3)
4)
5)
Optional the frequency inverter of this size is purchasable without brake transistor.

3.9 ACT 401 (75.0 up to 132.0 kW, 400 V)
Type
ACT 401 -43 -45 -47 -49
Output. motor side
Recommended shaft output P kW 75.0 90.0 110.0 132.0
Switching frequency f kHz 2, 4, 8
Output brake resistor (external) 5)
min. brake resistor R Ω 4.5 3.0
R Ω 6.1 5.1 4.1 3.8
(UdBC = 770 V)
Input, mains side
1) 1)
Mains current 2) 3ph/PE I A 143.0 172.0 208.0 1) 249.0 1)

Fuse 3ph/PE I A 160 200 250 315
UL-Type 600 VAC RK5. 3ph/PE I A 175 200 250 300
Mechanics
Weight (approx.) m kg 45 48
Terminals A mm2 up to 2 x 95
Form of assembly - - Vertical
Ambient conditions
Energy dissipation
P W 1600 1900 2300 2800
Output current 4)
Switching frequency
2 kHz 4 kHz 8 kHz
75 kW 150 A 150 A 150 A
90 kW 180 A 180 A 180 A
110 kW 210 A 210 A 210 A3)
132 kW 250 A 250 A 250 A3)
1)
2)
3)
4)
5)
Optional the frequency inverter of this size is purchasable without brake transistor.
24 24 Operating
3.10 Operation Diagrams
The technical data of the frequency inverters refer to the nominal point which was
selected to enable a wide range of applications. A functionally and efficient dimension-
ing (de-rating) of the frequency inverters is possible based on the following diagrams.
Site altitude
Power reduction (Derating), max. coolant temperature,
5%/1000 m above sea level, 3.3 °C/1000 m above sea level,
hmax = 4000 m
Coolant temperature in °C
100 55
Output current in %
85 45
60
40
20
1000 2000 3000 4000 1000 2000 3000 4000

Mounting altitude in m above sea level Mounting altitude in m above sea level
Coolant temperature
Power reduction (Derating)
2.5%/K upper 40 °C, Tmax= 55 °C
100
Output current in %
80
63
40
20
0 10 20 30 40 50 55
Coolant temperature in °C
Mains voltage
Reduction of output current at constant output power (Derating)
0.22%/ V upper 400 V, Umax= 480 V
100
Output current in %
83
63
40
20
0 400 420 440 460 480

Mains voltage equal output voltage in V

4 Mechanical Installation
The frequency inverters of degree of protection IP20 are designed, as a standard, for
installation in electrical cabinets.
• During installation, both the installation and the safety instructions as well as the
device specifications must be complied with.
Warning! To avoid serious physical injuries or major material damage, only quali-
fied persons are allowed to work on the devices.
Warning! During assembly, make sure that no foreign particles (e.g. filings, dust,
wires, screws, tools) can get inside the frequency inverter. Otherwise
there is the risk of short circuits and fire.
The frequency inverters comply with protection class IP20 only if the
covers and terminals are mounted properly.
The units may only be used if these requirements are met.
4.1 ACT 201 (up to 3.0 kW) and ACT 401 (up to 4.0 KW)
The frequency inverter is mounted in a vertical position on the assembly panel by
means of the standard fittings.
The following illustration shows the different mounting possibilities.
Standard installation
b c
x b1 b1 c1
a a1 a2
x
x 100 mm
Assembly is effected by inserting the long side of the fixing plate in the heat sink and
screwing it to the mounting plate.
The dimensions of the device and the installation dimensions are those of the stan-
dard device without optional components and are given in millimeters.
Dimensions in mm Installation dimensions in mm

Frequency inverter a b c a1 a2 b1 c1
0.55 kW ... 1.1 kW 190 60 178 210 ... 230 260 30 133
ACT 201
1.5 kW ... 3.0 kW 250 60 178 270 ... 290 315 30 133
0.55 kW ... 1.5 kW 190 60 178 210 ... 230 260 30 133
ACT 401
1.85 kW ... 4.0 kW 250 60 178 270 ... 290 315 30 133
Caution! Mount the devices with sufficient clearance to other components so that
the cooling air can circulate freely. Avoid soiling by grease and air pollu-
tion by dust, aggressive gases, etc.
26 26 Operating
4.2 ACT 201 (4.0 up to 9.2 kW) and ACT 401 (5.5 up to
15.0 kW)
means of the standard fittings. The following illustration shows the standard fitting.
b c
x b1 c1
a1 a a2
x
x 100 mm
fixing bracket top

(fixing with screws M4x20)
fixing bracket bottom

(fixing with screws M4x60)
Assembly is done by screwing the two fixing brackets to the heat sink of the fre-
quency inverter and the assembly panel.
The frequency inverters are provided with fixing brackets, which are fitted using four
thread-cutting screws.
4.0 … 5.5 kW 250 100 200 270 ... 290 315 12 133
ACT 201
7.5 … 9.2 kW 250 125 200 270 ... 290 315 17.5 133
5.5 ... 9.2 kW 250 100 200 270 ... 290 315 12 133
ACT 401
11.0 … 15.0 kW 250 125 200 270 ... 290 315 17.5 133

4.3 ACT 401 (18.5 up to 30.0 kW)
b
x c
b1
c1
a1 a a2
x
x 100 mm
fixing bracket top fixing bracket bottom

(fixing with screws M4x20) (fixing with screws M4x70)
thread-cutting screws. The dimensions of the device and the installation dimensions
are those of the standard device without optional components and are given in milli-
meters.
18.5 kW ... 30.0 kW 250 200 260 270 … 290 315 20 160
28 28 Operating
4.4 ACT 401 (37.0 up to 65.0 kW)
b c
x b1 c1
a a2
a1
x
x 100 mm
fixing braket top fixing braket bottom

(fixing with screws M5x20) (fixing with screws M5x20)
thread-cutting screws. The dimensions of the device and the installation dimensions
are those of the standard device without optional components and are given in milli-
meters.
37.0 kW ... 65.0 kW 400 275 260 425 .. 445 470 20 160

4.5 ACT 401 (75.0 up to 132.0 kW)
The frequency inverter is mounted in a vertical position on the assembly panel. The
following illustration shows the standard fitting.
c
c1
x 300 mm c2
x b
c3
x x 300 mm
b1
b2
b3
a1
The diameter of the assembly holes is 9 mm.
Assembly is done by screwing the back plate of the frequency inverter to the assembly
panel.

Frequency inverter a b c a1 b1 b2 b3 c1 c2 c3
75.0 ... 132.0 kW 510 412 351 480 392 382 342 338 305 110
30 30 Operating
5 Electrical Installation
The electrical installation must be carried out by qualified staff according to the gen-
eral and regional safety and installation directives. For a safe operation of the fre-
quency inverter it is necessary that the documentation and the device specifications
be complied with during installation and commissioning. In the case of special applica-
tions, you may also have to comply with further guidelines and instructions.
Danger! When the frequency inverter is disconnected from power supply, the
mains, DC-link voltage and motor terminals may still be live for some
time. Wait for some minutes until the DC link capacitors have discharged
before starting to work at the unit.
The connecting cables must be protected externally, considering the maximum volt-
age and current values of the fuses. The mains fuses and cable cross-sections are to
be selected according to EN 60204-1 and DIN VDE 0298 Part 4 for the nominal oper-
ating point of the frequency inverter. According to UL/CSA, the frequency inverter is
suitable for operation at a supply network of a maximum of 480 VAC which delivers a
maximum symmetrical current of 5000 A (effective value) if protected by fuses of
class RK5. Only use copper cables with a temperature range of 60/75 °C.
Warning! The frequency inverters are to be grounded properly, i.e. large connec-
tion area and with good conductivity. The leakage current of the fre-
quency inverters may be > 3.5 mA. According to EN 50178 a permanent
connection must be provided. The protective conductor cross-section
required for grounding the fixing plate must be at least 10 mm², or a
second protective conductor must be installed electrically parallel to the
first one. In these applications, the cross-section must correspond to the
recommended cross-section of the wire.
Note: The degree of protection IP20 can only be reached if the terminals are
fitted on the frequency inverter and the covers are properly mounted.
Connection conditions
− The frequency inverter is suited for connection to the public or industrial supply
mains according to the technical data. If the transformer output of the supply
mains is ≤ 500 kVA, the optional mains commutation choke is only necessary for
the frequency inverters identified in the technical data. The other frequency invert-
ers are suitable for connection without a mains commutating choke with a relative
mains impedance ≥ 1%.
− It must be checked, based on the specifications of EN 61000-3-2, if the devices
can be connected to the public supply means without taking additional measures.
The frequency inverters ≤ 9.2 kW with integrated EMC filter comply with the emis-
sion limits of the product standard EN 61800-3 up to a motor cable length of 10 m,
without additional measures being required. Increased requirements in connection
with the specific application of the frequency inverter are to be met by means of
optional components. Commutating chokes and EMC filters are optionally available
for the series of devices.
− Operation on unearthed mains (IT mains) is admissible after disconnection of the Y
capacitors in the interior of the device.
− Interference-free operation with residual-current device is guaranteed at a tripping
current ≥ 30 mA if the following points are observed:
− Pulse-current and alternating-current sensitive residual current devices (Type
A to EN 50178) in the case of a connection of frequency inverters with one-
phase power supply (L1/N)
− All-current sensitive residual current devices (Type B to EN 50178) in the case
of a connection of frequency inverters with two-phase (L1/L2) or three-phase
(L1/L2/L3) power supply.
− Use EMC filters with reduced leakage current or, if possible, do not use EMC
filters at all.
− The length of the shielded motor cable is ≤ 10 m and there are no additional
capacitive components between the mains or motor cables and PE.

5.1 EMC Information
The frequency inverters are designed according to the requirements and limit values
of product norm EN 61800-3 with an interference immunity factor (EMI) for operation
in industrial applications. Electromagnetic interference is to be avoided by expert in-
stallation and observation of the specific product information.
Measures
− Install the frequency inverters and commutating chokes on a metal mounting
panel. Ideally, the mounting panel should be galvanized.
− Provide proper equipotential bonding within the system or the plant. Plant compo-
nents such as control cabinets, control panels, machine frames, etc. must be con-
nected by means of PE cables.
− Connect the frequency inverter, the commutating choke, external filters and other
components to an earthing point via short cables.
− Keep the cables as short as possible, make sure that cables are installed properly
using appropriate cable clamps, etc.
− Contactors, relays and solenoids in the electrical cabinet are to be provided with
suitable interference suppression components.
A Mains Connection
A
The length of the mains supply cable is not lim-
B ited. However, it must be installed separate from
the control, data and motor cables.
B DC link connection
The frequency inverters are to be connected to
the same mains potential or a common direct
voltage source. Cables longer than 300 mm are to
be shielded. The shield must be connected to the
mounting panel on both sides.
C Control Connection
The control and signal cables must be kept physi-
cally separate from the power cables. The shield
of the control cables is to be connected to ground
potential properly, i.e. with good conductivity, on
both sides. Analog signal lines are to be con-
C nected to the shield potential on one side.
D
D Motor and brake resistor
The shield of the motor cable is to be connected
to ground potential properly on both sides. On the
motor side use a metal compression gland. On the
frequency inverter side an appropriate shield
clamp is to be used. The signal cable used for
monitoring the motor temperature must be kept
separate from the motor cable. Connect the shield
of this line on both sides. If a brake resistor is
used, the connection cable must also be shielded,
and the shield is to be connected to earth poten-
tial on both sides.
Attention! The frequency inverters meet the requirements of the low-voltage direc-
tive 73/23/EEC and the requirements of the EMC directive 89/336/EEC.
The EMC product standard EN 61800-3 relates to the drive system. The
documentation provides information on how the applicable standards
can be complied if the frequency inverter is a component of the drive
system. The declaration of conformity is to be issued by the supplier of
the drive system.
32 32 Operating
5.2 Block diagram
X10
A 1 S3OUT
2 X1 L1 L2 L3 + -
3
X210A
1 +20 V / 180 mA
2 GND 20 V
S1IND
B 3
S2IND + -
C 4
S3IND
5 U, I
S4IND
6
S5IND CPU
7
X210B
S6IND
1
2 GND 20 V
S1OUT
D 3
MFO1
E 4
5 +10 V / 4 mA
I
MFI1 A
F 6
D
7 GND 10 V X2 U V W Rb1 Rb2
A Relay connection S3OUT

Change-over contact, min. 50 000 switching operations,
response time approx. 40 ms, maximum contact load:
− make contact AC 5 A / 240 V, DC 5 A (ohmic) / 24 V DC
− break contact AC 3 A / 240 V, DC 1 A (ohmic) / 24 V DC
B Digital input S1IND

Digital signal, controller enable signal, response time approx. 16 ms (on), 10 μs (off),
Umax = DC 30 V, 10 mA at DC 24 V, PLC compatible
C Digital input S2IND ... S6IND

Digital signal: response time approx. 16 ms, Umax= DC 30 V, 10 mA at DC 24 V, PLC
compatible, frequency signal: DC 0...30 V, 10 mA at DC 24 V, fmax = 150 kHz
D Digital output S1OUT

Digital signal, DC 24 V, Imax = 40 mA,
PLC compatible, overload and short-circuit proof
E Multi-function output MFO1

Analog signal: DC 24 V, Imax = 40 mA, pulse-width modulated, fPWM = 116 Hz
Digital signal: DC 24 V, Imax = 40 mA,
frequency signal: DC 0...24 V, Imax = 40 mA, fmax = 150 kHz,
PLC compatible, overload and short-circuit proof
F Multi-function input MFI1

Analog signal: resolution 12 Bit, DC 0...10 V (Ri = 70 kΩ), 0...20 mA (Ri = 500 Ω),
digital signal: response time approx. 16 ms, Umax = DC 30 V, 4 mA at DC 24 V,
PLC compatible

5.3 Optional Components
Thanks to the modular hardware components, the frequency inverters can be inte-
grated in the automation concept easily. The standard and optional modules are rec-
ognized during the initialization, and the controller functionality is adjusted automati-
cally. For the information required for installation and handling of the optional mod-
ules, refer to the corresponding documentation.
Danger! The hardware modules at slots B and C may only be assembled and dis-
assembled after the frequency inverter has been disconnected safely from
power supply. Wait for some minutes until the DC link capacitors have
discharged before starting the work.
• The unit may only be connected with the power supply switched off.
• Make sure that the frequency inverter is discharged.
Hardware modules
A Control Unit KP500

Connection of the optional control unit KP500 or an interface
adapter KP232.
B Communication module CM
A Plug-in section for connection to various communication pro-
tocols:
− CM-232: RS232 interface
− CM-485: RS485 interface
− CM-PDP: Profibus-DP interface
B − CM-CAN: CANopen interface
C Expansion module EM
Slot for customer-specific adaptation of the control inputs
and outputs to various applications:
C
− EM-ENC: extended speed sensor evaluation
− EM-RES: resolver evaluation
− EM-IO: analog and digital inputs and outputs
− EM-SYS: system-bus
(system bus in combination with CM-CAN communication
module upon request)
Attention! If two optional components with CAN-Protocol controller are installed,

the system-bus interface in the EM expansion module is deactivated!
34 34 Operating
5.4 Connection of the device
5.4.1 Dimensioning of the conductor cross section

Dimension the wire according to the electrical load and applied voltage. Use a suitable
conductor cross section to reduce the voltage drop at the wire. The motor can not
obtain the full torque if the voltage drop at the wire is too high. Comply to the coun-
try-specific and application-specific regulations and to the UL-Notes. Suitable fuse
protection values for the mains connection are listed in the chapter “Technical data”.
Dimension the conductor cross section of the protective conductor (PE) according to
EN 61800-5-1:
Mains cable cross section Protective conductor (PE)
Up to 10 mm² Instal two protective conductors with the same
conductor cross section as for the mains cable or
10 mm2 conductor cross section.
10…16 mm² Instal a protective conductor with the same con-
ductor cross section as for the mains cable.
16…35 mm² Instal a protective conductor with 16 mm² conduc-
tor cross section.
> 35 mm² Instal a protective conductor with the half cross
section of the mains cable cross section.
5.4.1.1 Typical conductor cross sections

The following tables give an overview with typical conductor cross sections (copper
cable with PVC insulation, 30 °C ambient temperature, continuous mains current
maximum 100% of rated mains current). Dependening on the operation conditions
other conductor cross sections may be applicable.
230 V: one-phase (L/N) and two-phase (L1/L2) connection

ACT 201 Mains cable PE-conductor Motor cable
-05 0.55 kW
2x1.5 mm² or
-07 0.75 kW 1.5 mm² 1.5 mm²
1x10 mm²
-09 1.1 kW
-11 1.5
2x2.5 mm² or
-13 2.2 kW 2.5 mm² 1.5 mm²
1x10 mm²
-15 3 kW
2x4 mm² or
-18 4 kW 4 mm² 4 mm²
1x10 mm²
230 V: three-phase connection (L1/L2/L3)

-05 0.55 kW
-07 0.75 kW
-09 1.1 kW 2x1.5 mm² or
1.5 mm² 1.5 mm²
-11 1.5 kW 1x10 mm²
-13 2.2 kW
-15 3 kW
-18 4 kW 2x4 mm² or
4 mm² 4 mm²
-19 5.5 kW 1x10 mm²
2x 6 mm² or
-21 7.5 kW 6 mm² 6 mm²
1x10 mm²
-22 9.2 kW 10 mm² 1x10 mm² 10 mm²

400 V: three-phase connection (L1/L2/L3)
-05 0.55 kW
-07 0.75 kW
-09 1.1 kW
-11 1.5 kW 2x1.5 mm² or
1.5 mm² 1.5 mm²
-12 1.85 kW 1x10 mm²
-13 2.2 kW
-15 3 kW
-18 4 kW
-19 5.5 kW 2x2.5 mm² or
2.5 mm² 2.5 mm²
-21 7.5 kW 1x10 mm²
-22 9.2 kW 2x4 mm² or
4 mm² 4 mm²
-23 11 kW 1x10 mm²
2x6 mm² or
-25 15 kW 6 mm² 6 mm²
1x10 mm²
-27 18.5 kW
10 mm² 1x10 mm² 10 mm²
-29 22 kW
-31 30 kW 16 mm² 1x16 mm² 16 mm²
-33 37 kW 25 mm² 1x16 mm² 25 mm²
-35 45 kW
35 mm² 1x16 mm² 35 mm²
-37 55 kW
-39 65 kW 50 mm² 1x25 mm² 50 mm²
-43 75 kW 70 mm² 1x35 mm² 70 mm²
-45 90 kW 95 mm² 1x50 mm² 95 mm²
-47 110 kW 2x70 mm² 1x70 mm² 2x70 mm²
-49 132 kW 2x95 mm² 1x95 mm² 2x95 mm²
5.4.2 Mains Connection

The mains fuses and cable cross-sections are to be selected according to EN 60204-1
and DIN VDE 0298 Part 4 for the nominal operating point of the frequency inverter.
According to UL/CSA, approved Class 1 copper lines with a temperature range of
60/75°C and matching mains fuses are to be used for the power cables. The electrical
installation is to be done according to the device specifications and the applicable
standards and directives.
Caution! The control, mains and motor lines must be kept physically separate
from one another. The cables connected to the frequency inverters may
not be subjected to high-voltage insulation tests unless appropriate cir-
cuitry measures are taken before. Otherwise the unit may be damaged.

5.4.3 Motor connection
BONFIGLIOLI VECTRON recommends shielded cable for the motor connection to the
frequency inverter. The shield is to be connected to PE potential properly, i.e. with
good conductivity, on both sides. The control, mains and motor lines must be kept
physically separate from one another. The user must comply with the applicable limits
stipulated in the relevant national and international directives as regards the applica-
tion, the length of the motor cable and the switching frequency.
5.4.3.1 Motor cable length, without filter

Permissible length of motor cable without output filter
Frequency inverter unshielded cable shielded cable
0.55 kW … 1.5 kW 50 m 25 m
1.85 kW … 4.0 kW 100 m 50 m
5.5 kW … 9.2 kW 100 m 50 m
11.0 kW … 15.0 kW 100 m 50 m
18.5 kW … 30.0 kW 150 m 100 m
37.0 kW … 65.0 kW 150 m 100 m
75.0 kW … 132.0 kW 150 m 100 m
The specified lengths of the motor cables must not be exceeded if no output filter is
installed.
Note: The frequency inverters ≤ 9.2 kW with integrated EMC filter comply with
the emission limits stipulated in EN 61800-3 if the motor cable is not
longer than 10 m. The frequency inverters ≤ 9.2 kW of the construction
size 3 with integrated EMC filter comply with the emission limits stipulated
in EN 61800-3 if the motor cable is not longer than 20 m Customer-
specific requirements can be met by means of an optional filter.
5.4.3.2 Motor cable length, with output filter dU/dt

Longer motor cables can be used after taking appropriate technical measures, e.g.
use of low-capacitance cables and output filters. The following table includes standard
values if an output filter is used.
Permissible length of motor cable with output filter

Frequency inverter unshielded cable shielded cable
0.55 kW … 1.5 kW on inquiry on inquiry
1.85 kW … 4.0 kW 150 m 100 m
5.5 kW … 9.2 kW 200 m 135 m
11.0 kW … 15.0 kW 225 m 150 m
18.5 kW … 30.0 kW 300 m 200 m
37.0 kW … 65.0 kW 300 m 200 m
75.0 kW … 132.0 kW 300 m 200 m
5.4.3.3 Motor cable length, with sine filter

Longer motor cables can be used if sine filters are installed. The high-frequency cur-
rent components will be filtered out which results in smoothed current and allows
longer motor cables. Take the voltage drop at the wire and the sine filter into account.
The voltage drop causes an increase of the output current. Verify that the increased
output current can be achieved by the frequency inverter. Consider this for the engi-
neering.
If the motor cable is longer than 300 m please contact the BONFIGLIOLI service.

5.4.3.4 Group drive
For a group drive (several motors at one frequency inverter) the total length must be
shared in the number of motors according to the table values. A group drive with
synchronous servomotors is not possible.
Use a thermocouple for monitoring (for example PTC resistor) at each motor to avoid
damage.
5.4.3.5 Speed sensor connection

Install the speed sensor lines physically separate from the motor cables. Comply with
the manufacturer’s data of the speed sensor.
Install the shielding near to the frequency inverter and keep the speed sensor lines as
short as possible.
5.4.4 Connection of a Brake Resistor

The connection of a brake resistor is done via terminal X2.
Danger! Switch off power supply before connecting or disconnecting the brake
resistor cables. Dangerous voltage may be present at the motor terminals
and the terminals of the brake resistor even after the frequency inverter
has been disconnected safely from power supply. Wait for some minutes
until the DC link capacitors have discharged before starting to work at the
unit.
Caution! The brake resistor must be equipped with a temperature switch. The tem-
perature switch must disconnect the frequency inverter from mains supply
if the brake resistor is overloaded.
X2
Rb1 Rb2
L1 L2 L3
K1
Rb
Rb1 Rb2 X1
T1 T2
K1
Note: Keep the brake resistor lines as short as possible.
38 38 Operating
5.5 Connection of the construction sizes
5.5.1 ACT 201 (up to 3.0 kW) and ACT 401 (up to 4.0 kW)
The mains connection of the frequency inverter is done via plug-in terminal X1. The
connection of the motor and the brake resistor to the frequency inverter is done via
plug-in terminal X2. Degree of protection IP20 (EN60529) is only guaranteed if the
terminals are plugged in.
Danger! Switch off power supply before connecting or disconnecting the
keyed plug-in terminals X1 and X2. Dangerous voltage may be present
at the mains terminals and the DC terminals even after the frequency
inverter has been disconnected safely from power supply. Wait for some
minutes until the DC link capacitors have discharged before starting the
work.
Mains power connection ACT 201 (up to 3.0 kW) and

ACT 401 (up to 4.0 kW)
X1 Phoenix ZEC 1,5/ .. ST7,5
0.2 … 1.5 mm
2
AWG 24 … 16
0.2 … 1.5 mm
2
AWG 24 … 16
0.25 … 1.5 mm
2
AWG 22 … 16
0.25 … 1.5 mm
2
AWG 22 … 16
550 W … 1.1 kW
+ - L1 L2 L3 + - L1 L2 L3 + - L1 L2 L3
L1 N PE L1 L2 PE L1 L2 L3 PE
1ph / 230V AC 2ph / 230V AC 3ph / 230V AC
3ph / 400V AC
1.5 kW … 3.0 kW 1.5 kW … 3.0 kW 1.5 kW … 4.0 kW
+ - L1 L1 L2 L3 + - L1 L1 L2 L3 + - L1 L1 L2 L3
L1 N PE L1 L2 PE L1 L2 L3 PE
1ph / 230V AC 2ph / 230V AC 3ph / 230V AC
3ph / 400V AC
1 With a mains current above 10 A, the mains power connection 230 V 1ph/N/PE
and the mains power connection 230 V 2ph/N/PE are to be done on two termi-
nals.

Motor power connection ACT 201 (up to 3.0 kW) and
ACT 401 (up to 4.0 kW)
Phoenix ZEC 1,5/ .. ST7,5

0.2 … 1.5 mm2
AWG 24 … 16
0.2 … 1.5 mm2
AWG 24 … 16
0.25 … 1.5 mm2
AWG 22 … 16
0.25 … 1.5 mm2
AWG 22 … 16
X2
Rb1 Rb2 U V W
U V W U V W
Delta connection Star connection M

3~
Connection of brake resistor with temperature switch
X2
X2
Rb1 Rb2 U V W Phoenix ZEC 1,5/ .. ST7,5
0.2 … 1.5 mm
2
AWG 24 … 16
0.2 … 1.5 mm2
AWG 24 … 16
0.25 … 1.5 mm
2
Rb AWG 22 … 16
Rb1 Rb2
0.25 … 1.5 mm
2
T1 T2 AWG 22 … 16

5.5.2 ACT 201 (4.0 up to 9.2 kW) and ACT 401 (5.5 up to
15.0 kW)
mains cable to terminal X1 and the motor cable and the brake resistor
to terminal X2. Dangerous voltage may be present at the mains termi-
nals and the DC terminals even after the frequency inverter has been
disconnected safely from power supply. Wait for some minutes until the
DC link capacitors have discharged before starting the work.
Mains power connection ACT 201 (4.0 up to 9.2 kW) and

ACT 401 (5.5 up to 15.0 kW)
X1
X1
L1 L2 L3 - +
L1 L2 L3 PE
3ph / 230V AC
3ph / 400V AC
ACT 201-18 (4.0 kW):

X1
L1 L2 L3 - +
L1 N PE
1ph / 230V AC
4.0 kW & 9.2 kW 11 kW & 15 kW

6qmm / RM7,5 16qmm / RM10+15
0.2 & 6 mm 2 0.2 & 16 mm 2
AWG 24 & 10 AWG 24 & 6
0.2 & 6 mm 2 0.2 & 16 mm 2
AWG 24 & 10 AWG 24 & 6
0.25 & 4 mm 2 0.25 & 10 mm 2
AWG 22 & 12 AWG 22 & 8
0.25 & 4 mm 2 0.25 & 10 mm 2
AWG 22 & 16 AWG 22 & 8
ACT 201-18 (4.0 kW): one- and three-phase connection is possible.

ACT 201-19 (5.5 kW) and above: three-phase connection is possible

Motor power connection ACT 201 (4.0 up to 9.2 kW) and
ACT 401 (5.5 up to 15.0 kW)
X2
U V W Rb1 Rb2
X2
M
U V W U V W 3~
Delta connection Star connection
4.0 kW … 9.2 kW 11.0 kW … 15.0 kW

6qmm / RM7,5 16qmm / RM10+15
0.2 … 6 mm2 0.2 … 16 mm2
AWG 24 … 10 AWG 24 … 6
2 2
0.2 … 6 mm 0.2 … 16 mm
AWG 24 … 10 AWG 24 … 6
0.25 … 4 mm2 0.25 … 10 mm2
AWG 22 … 12 AWG 22 … 8
0.25 … 4 mm2 0.25 … 10 mm2
AWG 22 … 16 AWG 22 … 8
Connection of brake resistorwith temperature switch

X2
U V W Rb1 Rb2
X2
Rb
Rb1 Rb2
T1 T2
4.0 kW … 9.2 kW 11.0 kW … 15.0 kW
6qmm / RM7,5 16qmm / RM10+15
2 2
0.2 … 6 mm 0.2 … 16 mm
AWG 24 … 10 AWG 24 … 6
2 2
0.2 … 6 mm 0.2 … 16 mm
AWG 24 … 10 AWG 24 … 6
0.25 … 4 mm2 0.25 … 10 mm2
AWG 22 … 12 AWG 22 … 8
0.25 … 4 mm2 0.25 … 10 mm2
AWG 22 … 16 AWG 22 … 8

5.5.3 ACT 401 (18.5 up to 30.0 kW)
Mains power connection ACT 401 (18.5 up to 30.0 kW)
X1
18.5 kW … 30.0 kW
X1 PHOENIX MKDSP 25/ 6-15,00-F
L1 L2 L3 - + 2.5 Nm
22.1 lb-in
0.5 … 35 mm2
AWG 20 … 2
0.5 … 25 mm2
AWG 20 … 4
1.00 … 25 mm2
L1 L2 L3 PE AWG 18 … 4
3ph / 400V AC 1.5 … 25 mm2
AWG 16 … 4

Motor power connection ACT 401 (18.5 up to 30.0 kW)
X2
U V W Rb1 Rb2
X2
2.5 Nm
22.1 lb-in M
3~
18.5 kW … 30 kW
25/ 6-15,00
0.5 … 35 mm2
AWG 20 … 2
0.5 … 25 mm2
AWG 20 … 4 U V W U V W
1.00 … 25 mm2
AWG 18 … 4
1.5 … 25 mm2
AWG 16 … 4 Star connection Delta connection
X2
U V W Rb1 Rb2
X2
Rb
Rb1 Rb2
18.5 kW … 30 kW T1 T2
25/ 6-15,00
2.5 Nm
0.5 … 35 mm
2
22.1 lb-in
AWG 20 … 2
0.5 … 25 mm
2
AWG 20 … 4
1.00 … 25 mm
2
AWG 18 … 4
1.5 … 25 mm
2
AWG 16 … 4

5.5.4 ACT 401 (37.0 up to 65.0 kW)
X1
37.0 kW … 65.0 kW
X1 threaded bolt M8x25
2
wire cross section up to 70 mm
L1 L2 L3 - +
8 Nm
70.8 lb-in
L1 L2 L3 PE
3ph / 400V AC

X2
37.0 kW … 65.0 kW
X2
threaded bolt M8x25
wire cross section up to 70 mm
2
U V W Rb1 Rb2
8 Nm
70.8 lb-in
U V W U V W
M
3~ Star connection Delta connection
X2
37.0 kW … 65.0 kW
X2 threaded bolt M8x25
Wire cross section up to 70 mm
2
U V W Rb1 Rb2
8 Nm
70.8 lb-in
Rb
Rb1 Rb2
T1 T2
Note: Optional, the inverters in this size can be purchased without brake
chopper. The terminals Rb1 and Rb2 are then not connected internally.

5.5.5 ACT 401 (75.0 up to 132.0 kW)
mains cable, motor cable and the brake resistor. Dangerous voltage may
be present at the mains terminals and the DC terminals even after the
frequency inverter has been disconnected safely from power supply.
Wait for some minutes until the DC link capacitors have discharged be-
fore starting the work.
U V W
10 Nm
88.5 lb-in
Rb2 ZK+
L1 L2 L3 ZK-
L1 L2 L3
L1 L2 L3 PE
3ph / 400V AC
Threaded bolt M8x20

10 Nm
88.5 lb-in
U V W
Rb2 ZK+
U V W
L1 L2 L3 ZK-
M
3~
U V W U V W
Star connection Delta connection
Threaded bolt M8x20
10 Nm
88.5 lb-in
U V W
Rb2 ZK+
ZK+ Rb2
L1 L2 L3 ZK-
Rb
ZK+ Rb2
T1 T2
Threaded bolt M8x20
Note: Optional, the inverters in this size can be purchased without brake
chopper and are then not provided with the terminal Rb2 for a brake
resistor connection.

5.6 Control Terminals
The control and software functionality can be freely configured to ensure a reliable
and economical operation. The operating instructions describe the factory settings of
the standard connections in the relevant Configuration 30 as well as the software
parameters to be set up.
Caution! Switch off power supply before connecting or disconnecting the keyed
control inputs and outputs. Otherwise, components may be damaged.
Control Terminals
Wieland DST85 / RM3,5
0.14 … 1.5 mm2
AWG 30 … 16
0.14 … 1.5 mm
2
AWG 30 … 16
0.25 … 1.0 mm
2
AWG 22 … 18
0.25 … 0.75 mm2
AWG 22 … 20
0.2 … 0.3 Nm
1.8 … 2.7 lb-in
Control terminal X210A

Ter. Description
1 Voltage output 20 V, Imax=180 mA 1)
2 Ground / GND 20 V
3 Digital input S1IND, Umax= DC 30 V, 10 mA at DC 24 V, PLC compatible,
response time approx. 16ms (on), 10 μs (off)
4 Digital input EM-S2IND, Umax= DC 30 V, 10 mA at DC 24 V, PLC compatible,
response time approx. 16 ms
5 Digital input EM-S3IND, Umax= DC 30 V, 10 mA at DC 24 V, PLC compatible,
6 Digital input S4IND, Umax = DC 30 V, 10 mA at DC 24 V, PLC compatible,
frequency signal: 0...30 V, 10 mA at 24 V, fmax = 150 kHz
7 Digital input S5IND, Umax = DC 30 V, 10 mA at DC 24 V, PLC compatible,
frequency signal: 0...30 V, 10 mA at 24 V, fmax = 150 kHz
Control terminal X210B
Ter. Description
1 Digital input S6IND, Umax=30 V, 10 mA at 24 V, PLC compatible,
2 Ground / GND 20 V
3 Digital output S1OUT, U= DC 24 V, Imax=40 mA, overload and short-circuit proof
4 Multi-function output MFO1,
analog signal: U= DC 24 V, Imax=40 mA, pulse-width modulated, fPWM=116 Hz
digital signal: U= DC 24 V, Imax=40 mA, overload and short-circuit proof,
frequency signal: DC 0...24 V, Imax=40 mA, fmax=150 kHz
5 Reference output DC 10 V, Imax=4 mA
6 Multi-function input MFI1,
analog signal: resolution 12 Bit, DC 0... 10 V (Ri=70 kΩ), 0...20 mA (Ri=500 Ω),
digital signal: response time approx. 16 ms, Umax= DC 30 V, 4 mA at DC 24 V,
PLC compatible
7 Ground / GND 10 V
1)
The power supply at terminal X210A.1 may be loaded with a maximum current of
Imax = 180 mA. The maximum current available is reduced by the digital output
S1OUT and multifunctional output MFO1.

5.6.1 Relay Output
By default, the freely programmable relay output is linked to the monitoring function
(factory setting). The logic link to various functions can be freely configured via the
software parameters. Connection of the relay output is not absolutely necessary for
the function of the frequency inverter.
Relay Output
X10 Phoenix ZEC 1,5/3ST5,0
0.2 … 1.5 mm2
X10 AWG 24 … 16
1 0.2 … 1.5 mm2
2 S3OUT AWG 24 … 16
3 0.25 … 1.5 mm2
AWG 22 … 16
0.25 … 1.5 mm2
AWG 22 … 16
Control terminal X10
Ter. Description
1 .. 3 Relay output, floating change-over contact, min. 50 000 switching operations,
response time approx. 40 ms,
max. contact load, make contact AC 5 A / 240 V, DC 5 A (ohmic) / 24 V
max. contact load, break contact AC 3 A / 240 V, DC 1 A (ohmic) / 24 V
50 50 Operating
5.6.2 Control Terminals – Terminal Diagram
The control hardware and the software of the frequency inverter are freely configur-
able to a great extent. Certain functions can be assigned to the control terminals, and
the internal logic of the software modules can be freely selected.
Thanks to the modular design, the frequency inverter can be adapted to a great
range of different driving tasks.
The demands made of the control hardware and software are well known in the case
of standard driving tasks. This control terminal logic and internal function assign-
ments of the software modules are available in standard configurations. These as-
signments can be selected via parameter Configuration 30. For information on other
configurations, please contact us.
5.6.2.1 Configuration 110 – Sensorless Control

Configuration 110 contains the functions for variable-speed control of a 3-phase ma-
chine in a wide range of standard applications. The motor speed is set according to
the selected ratio of the reference frequency to the necessary voltage.
X210A Control terminal X210A
1 +20 V/180 mA X210A.1 Supply voltage +20 V
2 GND 20 V
X210A.2 Ground 20 V
3 S1IND
4 S2IND X210A.3 Controller release / error acknowl-
5 S3IND edgment
6 S4IND X210A.4 Start of clockwise operation
7 S5IND X210A.5 Start of anticlockwise operation
M X210A.6 Data set change-over 1
X210B X210A.7 Data set change-over 2
1 S6IND
2 GND 20 V Control terminal X210B
- + X210B.1 Motor thermal contact
- + 3 S1OUT
V 4 MFO1A X210B.2 Ground 20 V
5 +10 V/ 4 mA X210B.3 Operating message
6 MFI1A X210B.4 Analog signal of actual frequency
7 GND 10 V X210B.5 Supply voltage +10 V
Reference value potentiometer
X210B.6 Reference speed 0 ...+10 V
X210B.7 Ground 10 V

5.6.2.2 Configuration 111 – Sensorless Control with Technol-
ogy Controller
Configuration 111 extends the functionality of the sensorless control by software func-
tions for easier adaptation to the customer's requirements in different applications.
The Technology Controller enables flow rate, pressure, level or speed control.
2 GND 20 V
X210A.2 Ground 20 V
3 S1IND
5 S3IND edgment
6 S4IND X210A.4 Fixed percentage value change-
7 S5IND over 1
M X210A.5 Fixed percentage value change-
over 2
X210B
X210A.6 Data set change-over 1
1 S6IND
2 GND 20 V X210A.7 Data set change-over 2
- +
- 3 S1OUT
V + 4 MFO1A Control terminal X210B
5 +10 V/4 mA X210B.1 Motor thermal contact
+
6 MFI1A X210B.2 Ground 20 V
- 7 GND 10 V X210B.3 Operating message
X210B.4 Analog signal of actual frequency
X210B.5 Supply voltage +10 V
X210B.6 Actual percentage value 0 ...+10 V
X210B.7 Ground 10 V
5.6.2.3 Configuration 410 – Sensorless Field-Oriented Con-

trol
Configuration 410 contains the functions for sensorless, field-oriented control of a 3-
phase machine. The current motor speed is determined from the present currents and
voltages in combination with the machine parameters. Separate control of torque and
flux-forming current enables a high drive dynamics at a high load moment.
2 GND 20 V
X210A.2 Ground 20 V
3 S1IND
5 S3IND edgment
1 S6IND
- + 3 S1OUT
5 +10 V/4 mA X210B.3 Operating message
X210B.7 Ground 10 V
52 52 Operating
trol with Technology Controller
Configuration 411 extends the functionality of the sensor-less field-oriented control of
Configuration 410 by a Technology Controller. The Technology Controller enables a
control based on parameters such as flow rate, pressure, filling level or speed.
2 GND 20 V
X210A.2 Ground 20 V
3 S1IND
5 S3IND edgment
7 S5IND over 1
M X210A.5 no function assigned
1 S6IND X210A.7 Data set change-over 2
- 2 GND 20 V
+ 3 S1OUT Control terminal X210B
- +
V 4 MFO1A X210B.1 Motor thermal contact
+ 5 +10 V/4 mA X210B.2 Ground 20 V
6 MFI1A
X210B.3 Operating message
- 7 GND 10 V
X210B.7 Ground 10 V

trol, speed or torque controlled
Configuration 430 extends the functionality of the sensor-less field-oriented control of
Configuration 410 by a Torque Controller. The reference torque is represented as a
percentage and it is transmitted into the corresponding operational performance of
the application. Change-over between variable-speed control and torque-dependent
control is done via a digital control input.
2 GND 20 V
X210A.2 Ground 20 V
3 S1IND
5 S3IND edgment
7 S5IND X210A.5 n-/T change-over control function
1 S6IND
- + 3 S1OUT
6 MFI1A
7 GND 10 V
X210B.7 Ground 10 V

5.6.2.6 Configuration 210 – Field-Oriented Control, speed
controlled
Configuration 210 contains the functions for speed-controlled, field-oriented control of
a 3-phase machine with speed sensor feedback. The separate control of torque and
flux-forming current enables high drive dynamics with a high load moment. The nec-
essary speed sensor feedback results in a precise speed and torque performance.
2 GND 20 V
X210A.2 Ground 20 V
3 S1IND
5 S3IND edgment
+ - B
A
M X210A.6 Speed sensor track B
X210B X210A.7 Speed sensor track A
1 S6IND
- + 3 S1OUT
X210B.7 Ground 10 V
5.6.2.7 Configuration 211 – Field-Oriented Control, with

Technology Controller
Configuration 211 extends the functionality of the speed-controlled, field-oriented
control of Configuration 210 by a Technology Controller. The Technology Controller
enables a control based on parameters such as flow rate, pressure, filling level or
speed.
2 GND 20 V
3 S1IND X210A.2 Ground 20 V
+ - 5 S3IND edgment
B
A
7 S5IND over 1
M X210A.5 no function assigned
X210B X210A.6 Speed sensor track B
1 S6IND X210A.7 Speed sensor track A
2 GND 20 V
- + Control terminal X210B
- 3 S1OUT
V + 4 MFO1A X210B.1 Motor thermal contact
5 +10 V/4 mA X210B.2 Ground 20 V
+ 6 MFI1A X210B.3 Operating message
- 7 GND 10 V
X210B.7 Ground 10 V
54 54 Operating
5.6.2.8 Configuration 230 – Field-Oriented Control, speed
and torque controlled
Configuration 230 extends the functionality of Configuration 210 by functions for
torque-dependent, field-oriented control. The reference torque is represented as a
2 GND 20 V
X210A.2 Ground 20 V
3 S1IND
5 S3IND edgment
+ - B
A
7 S5IND X210A.5 n-/T change-over control function
M X210A.6 Speed sensor track B
X210B X210A.7 Speed sensor track A
1 S6IND
- + 3 S1OUT
X210B.7 Ground 10 V

6 Control Unit KP500
The optional KP500 control unit is a practical tool for controlling the frequency inverter
and setting and displaying the frequency inverter parameters.
The control unit is not absolutely necessary for the operation of the frequency inverter
and can be plugged on when required.
B C
D E
F H
G
I
Keys
A RUN Used for starting the drive and opening the CTRL menu.
Press the RUN key to open the motor potentiometer function.
STOP Used for opening the CTRL menu, stopping the drive and acknowledging
faults.
J Used for navigating in the menu structure and selecting parameters.
▲ ▼
Used for increasing/decreasing parameter values.
ENT Accessing parameters or changing the menu within the menu structure.
Confirmation of the selected function or the set parameter.
ESC Used for aborting parameters or switching back to the previous menu within
the menu structure. Canceling the function or resetting the parameter value.
FUN Used for switching over the key function, access to special functions.
Display
B Three-digit 7-segment display to show the parameter number.
C One-digit 7-segment display for display of the active data record, direction of rota-
tion etc.
D Display of the selected menu branch:
VAL Display actual values.
PARA Select parameters and adjust parameter values.
CTRL Select a function for adjustment and/or display via the control unit:
SEtUP guided commissioning.
CtrL motor potentiometer and jog function.
CPY Copy parameters via the control unit:
ALL All the parameter values are copied.
Act Only the active parameter values are copied.
FOr Control unit memory is formatted and deleted.
E Status and operating messages:
WARN Warning about a critical operating behavior.
FAULT Message indicating that the unit was switched off due to a fault.
RUN Flashing: signals readiness for operation.
Lights up: signals that the unit is operating and the output stage is enabled.
REM Active remote control via interface connection.
F Function switch-over with the FUN key.
F Five-digit 7-segment display for display of parameter value and sign.
G Physical unit of the parameter value displayed.
H Active acceleration or deceleration ramp.
I Current direction of rotation of the drive.

6.1 Menu Structure
The menu structure of the control unit is arranged as shown in the following illustra-
tion. In the optionally available PC user software VPlus, the functions and parameters
are structured in various levels depending on their function. The software contains the
full set of information and enables a flexible use of the parameter setting and control
options.
6.2 Main Menu

The various parameters and information of the frequency inverter can be displayed by
means of the control unit. The different functions and parameters are grouped to-
gether in four menu branches. From any point in the menu structure you can return
to the main menu by pressing the ESC key either continuously or repeatedly.
Note: In the following description of the key functions, a plus (+) between the
key symbols indicates that the keys have to be pressed at the same time.
A comma (,) between the key symbols indicates that the keys have to be
pressed one after the other.
Menu branch VAL

Display of actual values
Menu branch PARA
Display and edit parameters
Menu branch CPY
Copy parameters
Menu branch CTRL
Select control and test functions
Use the arrow keys to select the required menu branch. The selected menu branch is
displayed (flashing).
Select the menu branch by pressing the ENT key. The first parameter or the first func-
tion in the selected menu branch will be displayed.
Press the ESC key to return to the main menu of the control unit.
Keys
▲ ▼ Navigate through the menu structure and select a menu branch.
ENT Open the selected menu branch.
ESC Cancel the current menu branch and return to the main menu.

Operating ACTIVE
6.3 Actual Value Menu (VAL)
In the VAL menu branch, the control unit displays a variety of actual values, depend-
ing on the configuration selected and the options installed. The parameters and basic
software functions linked to the corresponding actual value are documented in the
operating instructions.
ESC
ENT
A ENT
ESC
D
B C
A Use the arrow keys to select the required number from the actual values dis-
played in numerical order.
In the current record, the record-related actual value parameters are displayed,
including the corresponding data record number. The seven-segment display
shows data record 0 if the actual values in the four data sets are identical.
Keys
▲+▼ Display the actual value parameter upon switch-on.
FUN , ▲ Display last actual value parameter (highest number).
FUN , ▼ Display first actual value parameter (lowest number).
B Use the ENT key to select the parameter. The parameter is displayed including
its current value, unit and the active data record.
C During commissioning, operation and error analysis, it is possible to monitor

each actual value parameter specifically.
Some of the actual value parameters are arranged in the four available data
records. If the parameter values in the four data records are identical, the actual
value is displayed in data record 0. If the actual values in the four data records
are different, diFF is displayed in data record 0.
Keys
▲,▼ Switch to another of the data set in the case of related actual
values.
FUN , ▲ Determine minimum value and display it permanently.
FUN , ▼ Determine maximum value and display it permanently.
FUN , ENT Display of mean value of the actual value during the
monitoring period.
D Use the ENT key to save the selected actual value as a parameter displayed at
switch-on. The message SEt (with parameter number) is displayed for a short
time. When the frequency inverter is switched on the next time, this actual value
will be displayed automatically.
E After saving the parameter, you can monitor and display the value again. Use
the ESC key to switch to the parameter selection of the VAL menu branch.
58 58 Operating
6.4 Parameter Menu (PARA)
The parameters to be configured during the guided commissioning were selected from
common applications and can be supplemented as required by further settings in the
PARA menu branch. The parameters and basic software functions linked to the corre-
sponding actual value are documented in the operating instructions.
ENT
A ENT
D
ESC
B C
A Use the arrow keys to select the required number from the parameters displayed
in numerical order. The parameter number is displayed with the active data set
(flashes).
In the current data set, the related parameters are displayed, including the cor-
responding data set number. The seven-segment display shows data set 0 if the
parameter values in the four data sets are identical.
Keys
▲+▼ Change to the last parameter edited.
FUN , ▲ Display of last parameter (highest number).
FUN , ▼ Display of first parameter (lowest number).
B Use the ENT key to select the parameter. The parameter is displayed including
its value, unit and the active data set. If settings are edited in data set 0, the
parameter values are changed in the four data sets.
C Use the arrow keys to adjust the parameter value or to select an operation
mode. The adjustment possibilities you have depend on the parameter.
Keep the arrow keys pressed for a while to change the displayed values quickly.
If you release the keys again, the speed at which the values change is reduced
again.
If the parameter value starts to flash, the speed at which the values change is
reset to the initial value again.
Keys
▲+▼ Set parameter to factory setting.
FUN , ▲ Set parameter to highest value.
FUN , ▼ Set parameter to smallest value.
FUN , ENT Change of the data set in the case of data set related parameters.
D Use the ENT key to save the parameter. For a short time, the message SEt in-
cluding the parameter number and the data set is displayed. To leave the pa-
rameter unchanged, press the ESC key.
Messages
Err1: EEPrO Parameter has not been saved.
Err2: StOP Parameter can only be read (i.e. not edited) when the unit is in
operation.
Err3: Error Other error.
E After saving the parameter, you can edit the value again or return to the pa-
rameter selection menu by pressing the ESC key.

6.5 Copy Menu (CPY)
With the copy function of the control unit you can copy the parameter values from the
frequency inverter to a non-volatile memory of the control unit (upload) and store
(download) them to a frequency inverter again.
The copy function makes the parameterization of recurring applications much easier.
The function archives all parameter values, regardless of access control and value
range. The memory space available in the control unit for the files is dynamically
scaled to match the scope of the data.
Note: The Copy Menu (CPY) is accessible in control level 3. The control level
can be adjusted, if necessary, via parameter Control Level 28.
6.5.1 Reading the Stored Information

When you open the CPY menu branch, the data stored in the
control unit are read out. This process takes a few seconds.
During this time, init and a progress indicator are displayed.
After the initialization in the copy menu, the function can be
selected.
If the information stored in the control unit is not valid, the
initialization is stopped and an error message is displayed.
In this case, the memory in the control unit must be formatted
as follows:
• Use the ENT key to confirm the error message.

• Use the arrow keys to select the function FOr.
• Use the ENT key to confirm the selection.
During the formatting operation, FCOPY and a progress
indicator are displayed.
The process takes a few seconds. When the process is
complete, the message rdY is displayed.
• Confirm the message by pressing the ENT key.
Now, you can select the copy function as described in the fol-
lowing.
60 60 Operating
6.5.2 Menu Structure
The copy menu CPY contains three main functions. Use the arrow keys to select the
required function. Select the source and the destination for the process. The memory
space available in the non-volatile memory of the control unit is displayed on the
three-digit seven-segment display as a percentage value.
Function – FOr
Use the function FOr to format and delete the memory in the
control unit. This may be necessary if a new control unit is
used for the first time.
Function – ALL
All readable and writable parameter values are transferred.
• Confirm this selection by pressing the ENT key and con-
tinue by selecting the source.
Function – Act
Only the active parameter values of the frequency inverter are
copied to the control unit. The number of active parameter
values depends on the current selected configuration of the
frequency inverter.
When data are copied from the control unit to the frequency
inverter, all parameter values stored are transferred, like in the
case of the ALL function.
• Confirm the selection Act by pressing the ENT key and
continue by selecting the source.
6.5.3 Selecting the Source

The parameters of the ALL and Act sub-functions in the CPY menu branch can be
parameterized to meet the requirements of the specific application.
The available memory space of the control unit is shown on the seven-segment
display.
• Use the arrow keys to select the data source (Src.) for the copy operation (up-
load). You can use either the data sets of the frequency inverter (Src. x) or the
files of the control unit (Src. Fy) as the data source.
• Confirm the selected data source by pressing the ENT key and continue by select-
ing the destination.
Display Description
Src. 0 The data of the four data records of the frequency inverter are copied.
Src. 1 The data of data record 1 of the frequency inverter are copied.
Src. E An empty data record for deletion of a file in the control unit.
Src. F1 File 1 is transferred from the memory of the control unit. 1)
1)
Empty files which are not filled with data yet cannot be used as signal sources. The
control unit memory is managed dynamically (see Chapter “Copy Menu (CPY)”)

6.5.4 Selecting the Destination
Select the destination (dSt.) of the copy operation (application-specific). The data
source is transferred to the selected target (download).
• Use the arrow keys to select the destination (dSt.) for the copied data
(download). Depending on the data source selected, either the data records of the
frequency inverter (dSt. x) or empty files of the control unit (dSt. F y) can be used
as the target.
• Confirm the selection by pressing the ENT key. The copy process is started and
COPY is displayed.
Display Description
dSt. 0 The four data records of the frequency inverter are overwritten.
dSt. 1 The data are copied to data record 1 of the frequency inverter.
dSt. F1 The data are copied to file 1 of the control unit. 1)
1)
Already existing files are not offered as possible targets.
6.5.5 Copy Operation

Attention! Before the parameter settings are transferred to the frequency inverter,
the individual parameter values are checked.
The value range and the parameter settings can differ according to the
power range of the frequency inverter. If parameter values are outside
of the value range, an error message will be displayed.
While the copy operation is in process, the message COPY

and, as a progress indicator, the number of the currently cop-
ied parameter will be displayed.
In the case of the Act function, the active parameter values
are copied only. Using the ALL function, parameters which are
not relevant to the selected configuration are copied, too.
Depending on the selected copy function (ALL or Act), the

copy operation is completed after some 100 seconds and the
display reads rdY.
Press the ENT key to switch to the copy menu. Use the ESC
key to switch to the target selection menu.
If the ESC key is pressed during the copy operation, the copy
operation is aborted before the transmission of the data is
complete. The message Abr and the number of the last pa-
rameter which was copied are displayed.
Press the ENT key to return to the selection in the copy menu.
Use the ESC key to switch to the target selection menu.
62 62 Operating
6.5.6 Error Messages
The copy function archives all parameters, regardless of the
access control and the value range. Some of the parameters
are only writable if the frequency inverter is not in operation.
The controller input (S1IND) may not be activated during the
copy operation, otherwise the data transmission is aborted.
The message S1Ind and the number of the last parameter
which was copied are displayed. If the controller enable input
is deactivated again, the aborted copy operation is continued.
The data transmission from the selected source to the destina-

tion is continuously monitored by the copy function. If an error
occurs, the copy operation is aborted and the message Err
and an error code are displayed.
Error Messages
Code Meaning
0 1 Write error in memory of control unit;
repeat the copy operation. If error message is displayed again, format
the memory.
2 Read error in memory of control unit;
repeat the copy operation. If error message is displayed again, format
the memory.
3 The size of the memory of the control unit was not determined cor-
rectly.
If this error occurs repeatedly, replace the control unit.
4 Not enough memory; the data are incomplete.
Delete the incomplete file and date no longer needed from the control
unit.
5 The communication has been disturbed or interrupted;
repeat the copy operation, delete the incomplete file if necessary.
1 0 Invalid identification of a file in the control unit;
delete faulty file and format memory if necessary.
2 The memory space of the selected target file is occupied;
delete file or use different target file in the control unit.
3 The source file to be read in the control unit is empty;
only files containing reasonable data should be selected as a source.
4 Defective file in control unit;
delete faulty file and format memory, if necessary.
2 0 The memory in the control unit is not formatted;
format the memory via the FOr function in the copy menu.
3 0 Error during reading of a parameter from the frequency inverter;
check connection between the control unit and the frequency inverter
and repeat reading operation.
1 Error during writing of a parameter in the frequency inverter;
Check connection between the control unit and the frequency inverter
and repeat the writing operation.
2 Unknown parameter type;
delete faulty file and format memory if necessary.
4 0 The communication has been disturbed or interrupted;
repeat the copy operation, delete the incomplete file if necessary.

6.6 Read data from the KP 500 control unit
The Parameter transfer operation mode enables the transmission of data from the
KP 500 control unit to the frequency inverter. In this operation mode, all functions of
the control unit are disabled except for the COPY function. Data transmission from the
frequency inverter to the control unit is also disabled.
Activation of the KP 500 control unit for Parameter transfer mode is prepared via the
parameter Program(ming) 34. For this purpose, the KP 500 control unit must be con-
nected to the frequency inverter.
Program(ming) 34 Function
The KP 500 control unit is prepared for parameter
111 - Parameter transfer transmission. A connected frequency inverter can re-
ceive data from the control unit.
110 - Normal mode Reset the KP 500 control unit to standard mode.
Attention! The KP 500 control unit can be activated for Parameter transfer only if
at least one file is stored in the control unit. Otherwise, the error mes-
sage "F0A10" will be displayed.
6.6.1 Activating
The KP 500 control unit can be configured both via the keys of the KP 500 and via any
other available CM communication module. To configure and activate the KP 500 con-
trol unit, proceed as follows:
Activation via keyboard of the control unit

• In the parameter menu PARA, use the arrow keys to select parameter Pro-
gram(ming) 34 and confirm the selection by pressing the ENT key.
• Use the arrow keys to enter the value 111 – Parameter transfer and confirm your
selection by pressing the ENT key.
Now, the control unit is ready for activation.
Before data can be transferred, the control unit must be initialized.
• Disconnect the control unit from the frequency inverter and re-connect it to the
same or another frequency inverter.
The initialization operation is started. During the initialization, init and a progress
indicator are displayed. After the initialization, the KP 500 control unit is ready for
transferring data to the frequency inverter.
Note: Setting the parameter Program(ing) 34 to 111 – Parameter transfer

can be undone by means of the control unit, provided that the control
unit has not been initialized yet.
• In parameter Program(ing) 34, use the arrow keys to enter the
value 110 – Normal Mode and confirm by pressing the ENT key.
64 64 Operating
Activation via CM Communication Module
Attention! Activation of the control unit via a communication connection is only
possible if the frequency inverter is equipped with an optional CM com-
munication module and the communication is effected via this module.
For this purpose, the control unit must be connected to the frequency
inverter.
• Establish a communication connection to the frequency inverter.

• Start the communication and select parameter Program(ing) 34 via the commu-
nication interface.
• Via the communication interface, enter and confirm the value 111 in parameter
Program(ing) 34.
• Via the communication interface, enter and confirm the value 123 in parameter
Program(ing) 34.
Frequency inverter is initialized again. The display of the control unit reads
"rESEt". Then, the initialization operation is started.
6.6.2 Transfer data

In order to transmit a file from the control unit to the frequency inverter, proceed as
follows:
• Connect the KP 500 control unit to the frequency inverter.

After the initialization, the data sources which are available for download are dis-
played.
• Use the arrow keys to select the data source (Src.F.y) for the copy operation from
the control unit to the frequency inverter.
The files stored in the control unit can be used as data sources.
Note: The files stored in the control unit contain all information and pa-
rameters stored in the control unit according to the selected copy
function ALL or Act (see Chapter “Copy Menu (CPY)”).
• Confirm the selection by pressing the ENT key.
The copy operation is started. The message COPY and the number of the cur-
rently processed parameter will be displayed to indicate the progress of the opera-
tion.
After the copy operation is complete, the control unit is initialized again.

6.6.3 Reset to Normal Mode
A KP 500 control unit which was activated as a Download Keypad can be reset to
standard operation mode with full functionality via a special key sequence on the con-
trol unit or via any available CM communication module.
Resetting at control unit

• Press the control unit keys RUN and STOP at the same time for about 1 second.
The display shows – – – – – . Subsequent the topmost operation level of the
control unit display is available.
• In the parameter menu PARA, use the arrow keys to select parameter Pro-
gram(ming) 34 and confirm the selection by pressing the ENT key.
• Use the arrow keys to enter the value 110 – Normal Mode and confirm your se-
lection by pressing the ENT key.
• Disconnect the control unit from the frequency inverter and re-connect it.
After the initialization, the control unit is ready for operation with its full function-
ality.
Resetting via CM communication module and/or control software VPlus

Attention! Resetting the control unit via a communication connection is only possi-
ble if the frequency inverter is equipped with an optional CM communi-
cation module and the communication is effected via this module.
• Establish a communication connection to the frequency inverter.

• Start the communication and select parameter Program(ing) 34 via the commu-
nication connection.
• Via the communication connection, enter and confirm the value 110 in parameter
Program(ing) 34.
• Via the communication connection, enter and confirm the value 123 in parameter
Program(ing) 34.
The frequency inverter is reset. The display of the control unit reads "rESEt".
After reset, the control unit is ready for operation with its full functionality.
6.7 Control Menu (CTRL)

Note: In order to be able to control the drive via the control unit, the digital
controller input S1IND must be connected and set to "High-Signal" in
order to enable the output stage.
Warning! • Switch off power supply before connecting and disconnecting control
terminal S1IND.
• When the frequency inverter is disconnected from power supply, the
mains, DC-link voltage and motor terminals may still be live for
some time. Wait for some minutes until the DC link capacitors have
discharged before starting to work at the unit.
66 66 Operating
The frequency inverters can be controlled by means of the control unit and/or a com-
munication module. In the CTRL menu branch, various functions are available which
make commissioning easier and enable the control of the inverter via the control unit.
If you want to control the frequency inverter via an optional communication module,
the necessary adjustments can be made via parameter Local/Remote 412. Via this
parameter, you can specify which functions will be available to the controller. Depend-
ing on the operation mode selected, only some of the control menu functions are
available. Refer to Chapter “Bus controller” for a detailed description of the parameter
Local/Remote 412.
6.8 Controlling the Motor via the Control Unit

The control unit enables controlling the connected motor in accordance with the se-
lected operation mode of parameter Local/Remote 412.
Note: In order to be able to control the drive via the control unit, the digital
controller input S1IND (controller release) must be connected and set to
"High-Signal" in order to enable the output stage.
terminal S1IND.
mains, DC-link voltage and motor terminals may still be live for
some time. Wait for some minutes until the DC link capacitors have
discharged before starting to work at the unit.
: When the RUN key was pressed, the drive was in operation already.

The CTRL menu branch can be accessed via the navigation
within the menu structure. The CtrL function contains sub-
functions which are displayed according to the operating point
of the frequency inverter.
Press the RUN key anywhere within the menu structure to
access the motor potentiometer function PotF. for clockwise
operation or Potr for anti-clockwise operation directly.
If the drive is running already, the display reads intF (foward,

clockwise operation) / intr (reverse, anti-clockwise operation)
for the function internal reference value or inPF (forward,
clockwise operation) / inPr (reverse, anti-clockwise operation)
for the function
"Motorpoti (KP)".
The function Motorpoti (KP) enables a link to other reference
value sources in the frequency reference value channel. The
function is described in Chapter “Motorpoti (KP)”.
Motor potentiometer function Pot

Use the arrow keys to adjust the output frequency of the fre-
quency inverter from the minimum frequency 418 to the
maximum frequency 419. The acceleration corresponds to the
factory settings (2 Hz/s) for parameter Ramp Keypad-
Motorpoti 473. The parameters Acceleration (Clockwise) 420
and Deceleration (Clockwise) 421 are considered in the case
of low acceleration values.
Function Motorpoti (KP) inP

Use the arrow keys to adjust the output frequency of the fre-
quency inverter from the Minimum Frequency 418 to the
Maximum Frequency 419. The adjusted frequency value by
means of the control unit can be connected with further refer-
ence values via Reference Frequency Source 475. (Refer to
chapter “Frequency Reference Channel” and "Motorpoti (KP)".)
Internal reference value int

The drive is in operation, i.e. output signals are present at the
frequency inverter and the current actual value is displayed.
Press an arrow key to switch to the motor potentiometer func-
tion Pot. The current frequency value is taken over in the mo-
tor potentiometer function Pot.
JOG frequency JOG

This function is useful for manual setup and positioning of a
machine. The frequency of the output signal is set to the en-
tered value if the FUN key is pressed.
• Press FUN key to switch from the internal reference value

int or the motor potentiometer function Pot to the pa-
rameter JOG frequency 489.
• Keep the FUN key pressed and press the arrow keys to
adjust the required frequency.
• (The frequency value last adjusted is saved as the JOG
frequency 489.)
• Release the FUN key to stop the drive.
• (The display returns to the previous function Pot or int or
to inP if function "Motorpoti (KP)" is active.)

Key functions
ENT Reversal of the direction of rotation independent of the control signal on
the terminals Clockwise S2IND or Anticlockwise S3IND.
ESC Cancel function and return to the menu structure.
FUN Switch from internal set point int or rather motor potentiometer function
Pot to JOG frequency; the drive starts.
Release the key to switch to the sub-function and stop the drive.
RUN Start drive; alternative to control signal S2IND or S3IND.
STOP Stop drive; alternative to control signal S2IND or S3IND.
Attention! If you press the ENT key, the direction of rotation is changed inde-
pendent of the signal on the terminals Clockwise S2IND or Anticlockwise
S3IND.
If the minimum frequency 418 has been set to 0.00 Hz, the direction
of rotation of the motor changes as soon as the sign of the reference
frequency value changes.

Operating ACTIVE
7 Commissioning of the Frequency Inverter
7.1 Switching on Mains Voltage
After completion of the installation work, make sure to check all control and power
connections again before switching on the mains voltage. If all electrical connections
are correct, make sure that the frequency inverter is not enabled (control input S1IND
open). After power-up, the frequency inverter carries out a self-test and the relay
output (X10) reports "Fault".
After a few seconds, the self-test is complete, the relay (X10) picks up and signals "no
fault ".
If the unit is in "as-delivered" condition or after resetting the unit to the factory set-
tings, the guided commissioning procedure is started automatically. On the control
unit, the “SetUP“ menu from the menu branch CTRL is displayed.
7.2 Setup Using the Control Unit

The guided commissioning of the frequency inverter determines all parameter settings
relevant to the required application. The available parameters were selected based on
known standard drive applications. This facilitates the selection of the important pa-
rameters. After successful completion of the SETUP routine, the actual value Actual
frequency 241 from the VAL menu branch is displayed on the control unit. Now, the
user should check whether further parameters are relevant for the application.
Note: The guided commissioning contains the function for parameter identifica-
tion. The parameters are determined by way of measurement and set
accordingly. In the case of higher requirements as regards the accuracy of
the speed/torque control, you should carry out the guided commissioning
procedure once again under operating conditions because part of the
machine data depends on the operating temperature.
When the unit is in "as-delivered" condition, the guided commis-
sioning procedure is started automatically. After successful commis-
sioning, the guided commissioning can be carried out again later via
the sub-menu CTRL.
• Use the ENT key to switch to the CTRL sub-menu.
• In the CTRL sub-menu, select the menu item "SEtUP" and con-
firm by pressing the ENT key.
• Use the ENT key to select parameter Configuration 30. ENT
The available configurations are displayed automatically depending

on the selected Control level 28.
• Use the arrow keys to enter the number of the required con- ENT
figuration. (for a description of the configurations, refer to the

following chapter)
If the setup was changed, the hardware and software functionality
will be configured. The message "SEtUP" is displayed again.
Confirm this message by pressing the ENT key in order to continue
the commissioning procedure.
• Switch to the next parameter.
• After initialization, confirm the selected configuration by pressing the ENT key.
• Continue the guided commissioning procedure according to the following chap-

ters.

7.2.1 Configuration
Parameter Configuration 30 determines the assignment and basic function of the
control inputs and outputs as well as the software functions. The software of the fre-
quency inverter offers several configuration options. These differ with respect to the
way in which the drive is controlled. Analog and digital inputs can be combined and
complemented by optional communication protocols as further reference value
sources. The operating instructions describe the configurations and the relevant pa-
rameters in the third Control level 28 (adjustment of parameter Control level 28 to
value 3).
Configuration 110, sensorless control

the V/f characteristic in accordance with the voltage/frequency ratio.
Configuration 111, sensorless control with technology controller

Configuration 111 extends the functionality of the sensor-less control by software
functions for easier adaptation to the customer's requirements in different applica-
tions. The Technology Controller enables flow rate, pressure, level or speed control.
Configuration 410, sensorless field-oriented control

Configuration 410 contains functions for sensor-less, field-oriented control of a 3-
phase machine. The current motor speed is determined from the present currents and
voltages in combination with the machine parameters. In this configuration, parallel
connection of several 3-phase motors is possible to a limited extent only.

with Technology Controller
Configuration 411 extends the functionality of Configuration 410 by a Technology
Controller. The Technology Controller enables a control based on parameters such as
flow rate, pressure, filling level or speed.

with speed/torque control
Configuration 210, field-oriented control

Configuration 211, field-oriented control with technology controller

Controller. The Technology Controller enables a control based on parameters such as
flow rate, pressure, filling level or speed.
Configuration 230, field-orientated control with speed/torque control


7.2.2 Data Set
The data set change-over function enables the selection of one of four data sets for
storing parameter settings.
If data set 0 is selected (factory setting), the parameter values stored in data set 0 are
copied to data sets 1 through 4. In this way, all values determined during the guided
commissioning procedure are saved in all data sets. In the factory settings, the fre-
quency inverter uses data set 1 as the active data set. (For information on data set
change-over via logic signals, refer to the chapter "Data Set Change-Over").
For example, if data set 2 is selected for guided commissioning ("SETUP"), all values
which were determined or entered are saved in this data set. In this case, the other
data sets do not contain any defined values. For the operation of the frequency in-
verter, data set 2 must be selected as the active data set in this case.
Data Set Setup

dS Function
0 All data sets (DS0)
1 Data set 1 (DS1)
2 Data set 2 (DS2)
3 Data set 3 (DS3)
4 Data set 4 (DS4)
7.2.3 Motor Type

The properties of the control functions and methods to be set vary depending on the
motor which is connected. The parameter Motor type 369 offers a range of motor
variants with the corresponding table values. The verification of the entered rated val-
ues and the guided commissioning are carried out on the basis of the parameterized
motor type. The selection of motor types varies depending on the requirements of the
different control methods. In operating instructions the functionality and operating
performance are described for 3-phase motors.
Motor type 369 Function

0 - Unknown The motor is not a standard type.
1 - Asynchronous Three-phase asynchronous motor, squirrel cage.
2 - Synchronous Three-phase synchronous motor.
3 - Reluctance Three-phase reluctance motor.
10 - Transformer Transformer with three primary windings.
Caution! Polling and presetting of parameter values depends on the operation mode
selected for parameter Motor type 369.
If the motor type is not entered correctly, the drive may be damaged.
When the motor type is specified, the machine data must be entered. This is described
in the following chapter. The data are polled in accordance with the table below.
72 72 Operating
7.2.4 Machine Data
The machine data to be entered during the guided commissioning procedure are indi-
cated on the type plate or the data sheet of the motor. The factory settings of the
machine parameters are based on the nominal data of the frequency inverter and the
corresponding four-pole three-phase motor. The entered and calculated machine data
are checked for plausibility during the guided commissioning procedure. The user
should verify the factory-set rated data of the three-phase motor.
UFIN, IFIN, PFIN are rated values of the frequency inverter.
Parameter Settings
No. Description Min. Max. Fact. sett.
370 Rated Voltage 0.17⋅UFIN 2⋅UFIN UFIN
371 Rated Current 0.01⋅IFIN 10⋅o ⋅ IFIN IFIN
372 Rated Speed 96 min-1 60 000 min-1 nN
374 Rated Cosinus Phi 0.01 1.00 cos(ϕ)N
375 Rated Frequency 10.00 Hz 1000.00 Hz 50.00
376 Rated mechanical power 0.01⋅PFIN 10⋅PFIN PFIN
• Use the arrow keys to select the required parameter and edit the parameter
value.
• Use the ENT key to confirm the selected parameter and the parameter values
entered.
Attention! The rated data of the motor are to be entered according to the specifica-
tions on the rating plate for the motor connection type used (star or
delta connection). If the data entered deviate from the rating plate, the
parameters will not be identified correctly. Parameterize the rated data
according to the specifications for the motor winding connection indi-
cated on the rating plate. Take the higher rated current of the connected
asynchronous motor into account.

7.2.5 Plausibility check
After the machine data (and the speed sensor data, if applicable) have been entered,
the calculation or examination of the parameters is started automatically. The display
changes over to "CALC" for a short time. If the verification of the machine data is
successful, the guided commissioning procedure continues with the identification of
the parameters.
Verification of the machine data should only be skipped by experienced users. The
configurations contain complex control processes which depend to a large degree on
the correctness of the machine parameters entered.
The warning and error messages displayed during the verification process have to be
observed. If a critical condition is detected during the guided commissioning, it is dis-
played by the control unit. Depending on the deviation from the expected parameter
value, either a warning or an error message is displayed.
− To ignore the warning or error messages, press the ENT key. The guided commis-
sioning is continued. However, it is recommended that the data be checked and
corrected if necessary.
− To correct the entered parameter values after the warning or error message, press
the ESC key. Use the arrow keys to switch to the parameter value which is to be
corrected.
Warning Messages
Code Measures / Remedy
No warning message present. This message can be read out via an optional
SA000
communication module.
The value of the parameter Rated voltage 370 is out of the rated voltage
SA001 range of the frequency inverter. The maximum reference voltage is indi-
cated on the rating plate of the frequency inverter.
For a three-phase motor, the calculated efficiency is in the limit range.
SA002 Check the values entered for the parameters Rated voltage 370, Rated
current 371 and Rated power 376.
The value entered for parameter Rated cos phi 374 is outside of the nor-
SA003
mal range (0.6 to 0.95). Check the value.
For three-phase motor, the calculated slip is in the limit range.
SA004 Check the values entered for parameters Rated speed 372 and Rated fre-
quency 375.
74 74 Operating
If an error message is displayed, the rated values must be checked and corrected.
The guided commissioning procedure is repeated until the rated values have been
entered correctly. Aborting the guided commissioning procedure by pressing ESC key
should only be done by expert users because it may be possible that rated values
have not been entered or determined correctly.
Error Messages
SF000 No error message exists.
The value entered for parameter Rated current 371 is too low. Correct the
SF001
value.
The value for parameter Rated current 371 is too high, referred to pa-
SF002
rameters Rated power 376 and Rated voltage 370. Correct the values.
The value entered for parameter Rated cos phi 374 is wrong (greater than
SF003
1 or smaller than 0.3). Correct the value.
The calculated slip frequency is negative. Correct the values entered for
SF004
parameters Rated speed 372 and Rated frequency 375.
The calculated slip frequency is too high.
SF005 Correct the values entered for parameters Rated speed 372 and Rated fre-
quency 375.
The calculated total output of the drive is lower than the rated power. Cor-
SF006
rect the value entered for parameter Rated power 376.
The set configuration is not supported by the guided commissioning. For
SF007 parameter Configuration 30, select one of the configurations described in
these operating instructions.
7.2.6 Parameter identification

In addition to the parameterized rated data, the selected configuration demands
knowledge of further machine data not stated on the rating plate of the three-phase
machine. In addition to entering the rated motor parameters or as an alternative, the
required machine data can also be measured during the guided commissioning proc-
ess. The machine data are measured while the drive is at a standstill. The measured
values are entered in the parameter automatically either directly or after the calcula-
tion. The procedure and the duration of the parameter identification depend on the
type of machine connected and the device.
After checking the machine data entered, the guided commissioning switches to the
parameter identification.
• Confirm the display "PAidE" by pressing the ENT key.
During the parameter identification, the connected load is measured.
The safety functions of the frequency inverter avoid a release of the power unit if no
signal is present at digital input S1IND. If a signal was already applied at the begin-
ning of the guided commissioning, the "S1Ind" message is not displayed.
Note: The parameter identification feature of the frequency inverter requires

the presence of a signal at digital input S1IND for release of the power
unit.

Operating ACTIVE
Warning! Switch off power supply before connecting and disconnecting control
terminal S1IND.
When the frequency inverter is disconnected from power supply, the
time. Wait for some minutes until the DC link capacitors have discharged
before starting to work at the unit.
• Confirm the final "rEAdY" message by pressing the ENT key.

Canceling the operation with the ESC key or withdrawing the release signal S1IND
results in an incomplete take-over of the values.
Note: In the case of higher requirements as regards the accuracy of the

speed/torque control, you should carry out the guided commissioning
procedure once again under operating conditions because part of the
machine data depends on the operating temperature.
During this procedure, confirm the machine data already entered.
After completion of the parameter identification, warning messages may be displayed.

Depending on the warning message code, the following instructions should be fol-
lowed and the measures indicated should be taken.
Warning Messages
SA0021 The stator resistance is very high. The following causes are possible:
− The motor cable cross-section is not sufficient.
− The motor cable is too long.
− The motor cable is not connected correctly.
− The contacts are not in a proper condition (corrosion).
SA0022 The rotor resistance is very high. The following causes are possible:
− The motor cable cross-section is not sufficient.
− The motor cable is too long.
− The motor cable is not connected correctly.
− The contacts are not in a proper condition (corrosion).
SA0041 The slip speed was not determined correctly. Check the values entered for
SA0042 The slip speed was not determined correctly. Check the values entered for
SA0051 The machine data for star connection were entered, the motor, however, is
connected in delta. For star operation, change the motor cable connection.
For delta operation, check the entered rated motor values.
Repeat the parameter identification.
SA0052 The machine data for delta connection were entered, the motor, however,
is connected in star. For delta operation, change the motor cable connec-
tion. For star operation, check the entered rated motor values.
Repeat the parameter identification.
SA0053 A phase asymmetry was measured. Check the cables at the terminals of
the motor and the frequency inverter for proper connection and check the
contacts for corrosion.
76 76 Operating
After completion or during the parameter identification, error messages may be dis-
played. Depending on the error code, the following instructions should be followed
and the measures indicated should be taken.
Error Messages
SF0011 The main inductance measurement has failed because the motor has a
high slip. Correct the rated motor values in parameters 370, 371, 372,
374, 375 and 376. Carry out the guided commissioning once again. In
case an error message is displayed again, enter the value 110 for parame-
ter Configuration 30 (sensorless regulation according to U/f-characteristic)
if value 410 was set so far. Carry out the guided commissioning once
again.
SF0012 The leakage inductance measurement has failed because the motor has a
high slip. Correct the rated motor values in parameters 370, 371, 372,
374, 375 and 376. Carry out the guided commissioning once again. In
case an error message is displayed again, enter the value 110 for parame-
ter Configuration 30 (sensorless regulation according to U/f-characteristic)
if value 410 was set so far. Carry out the guided commissioning once
again.
SF0021 The measurement of the stator resistance did not deliver a plausible value.
Check the cables at the terminals of the motor and the frequency inverter
for proper connection and check the contacts for corrosion and safe con-
tact. Repeat the parameter identification.
SF0022 The measurement of the rotor resistance did not deliver a plausible value.
Check the cables at the terminals of the motor and the frequency inverter
for proper connection and check the contacts for corrosion and safe con-
tact. Repeat the parameter identification.
7.2.7 Application data

Due to the wide range of drive applications with the resulting parameter settings it is
necessary to check further parameters. The parameters polled during the guided
commissioning procedure were selected from standard applications. After completion
of commissioning, further parameters can be set in the PARA menu branch.
7.2.7.1 Acceleration and deceleration

The settings define how fast the output frequency changes after a reference value
change or a start, stop or brake command.
Parameter Settings
420 Acceleration (Clockwise) 0.00 Hz/s 999.99 Hz/s 5.00 Hz/s
421 Deceleration (Clockwise) 0.00 Hz/s 999.99 Hz/s 5.00 Hz/s
Attention! The deceleration of the drive is monitored in the default parameter set-
ting Voltage controller operation mode 670. The deceleration ramp can
be extended in the case of an increase in the DC link voltage during
regenerative operation and/or during the braking process.

7.2.7.2 Set points at multi-functional input
The multi-functional input MFI1 can be parameterized for a reference value signal in
Operation mode 452. Operation mode 3 should only be selected by expert users for
drive control via Fixed frequency 1 480 and Fixed frequency 2 481.
Operation mode 452 Function

1 - Voltage Input Voltage signal (MFI1A), 0V ... 10V
2 - Current Input Current signal (MFI1A), 0mA ... 20mA
3 - Digital Input Digital signal (MFI1D), 0V ...24V
• Confirm the "End" display by pressing the ENT key.

The guided commissioning of the frequency inverter is terminated via a reset and the
initialization of the frequency inverter. The relay output X10 signals a fault.
After successful initialization of the frequency inverter, the factory-set parameter Ac-
tual frequency 241 is displayed. If a signal is present at digital inputs S1IND (control-
ler release) and S2IND (start clockwise operation) or at digital inputs S1IND (control-
ler release) and S3IND (start of anti-clockwise operation), the drive is accelerated to
the adjusted minimum frequency 418 (default values: 3.50 Hz in configurations 110,
111, 410, 411, 430 and 0.00 Hz in configurations 210, 211, 230).
7.2.7.3 Selection of an actual value for display

After commissioning, the value of parameter Actual frequency 241 is displayed at the
control unit KP500.
If another actual value is to be displayed after a restart, make the following settings:
• Use the arrow keys to select the actual value to be displayed as from now.
• Use the ENT key to display the value of the parameter.
• Press the ENT key again. "SEt" is displayed for confirmation.
As from now, the selected actual value is displayed after each restart.
If the parameter settings were made via the optional control software or in the PARA
menu branch of the control unit, the display of the selected actual value must be acti-
vated manually. Use the ESC key to switch to the selection of the actual value for
display again.
78 78 Operating
7.3 Check direction of rotation
Warning! Dangerous voltage may be present at the motor terminals and the ter-
minals of the brake resistor even after the frequency inverter has been
disconnected from power supply. Wait for some minutes until the DC
link capacitors have discharged before starting to work at the unit.
To check if the reference value and the actual direction of rotation of the drive corre-
spond to one another, proceed as follows:
• Operate the drive at low speed, i.e. specify a reference value of approx. 10%.
• Release the frequency inverter briefly {signal at digital inputs S1IND (controller
release) and S2IND (start of clockwise operation) or S1IND (controller release)
and S3IND (start of anti-clockwise operation)}.
• Check if the motor shaft turns in the required direction.
In case the sense of rotation is wrong, exchange two motor phases, e.g. U and V
at the terminals of the frequency inverter. The mains-side connection of the fre-
quency inverter does not affect the sense of rotation of the drive. In addition to
checking the drive, the corresponding actual values and operating messages can
be read out by means of the control unit.
Note: The commissioning of the frequency inverter is complete and can be

complemented by further settings in the PARA menu. The set parame-
ters have been selected in such a way that they are sufficient for com-
missioning in most applications. The other settings which are relevant to
the application can be checked according to the operating instructions.
If the controller release of the frequency inverter at S1IND is switched off the power
output stage will be disabled. The motor will coast down or, if installed, a break will
be activated.

7.4 Speed sensor
For some configurations an incremental speed sensor must be connected. Dependent
on the speed sensor type it can be connected to the basic device or to an expansion
module. Some applications require the connection to the basic device as well as to the
expansion module.
The source of the actual speed value is selected via parameter Actual Speed
Source 766. By default, speed sensor 1 is used as the actual speed source. If speed
sensor 2 of an expansion module delivers the actual value signal for the speed con-
troller, speed sensor 2 must be selected as the source.
Actual Speed Source 766 Function

The actual speed source is speed sensor 1 of the
1 - Speed Sensor 1
basic device (factory setting).
The actual speed source is speed sensor 2 of an
2 - Speed Sensor 2
expansion module.1)
1)
Only available if an expansion module is installed.
Dependent on the application and applied speed sensors the settings of parameters
must be adapted according to the following table.
Parameter Only Only Both

speed sensor 1 speed sensor 2 speed sensors
490 Operation Mode >0 0 - Off >0
speed sensor 1
491 Division Marks 1…8192 X 1…8192
speed sensor 1
493 Operation Mode 0 - Off 0 >0
speed sensor 2
494 Division Marks X 1…8192 1…8192
speed sensor 2
495 Level X Selection Selection
766 Actual Speed Source 1 2 1 or 2
X: can be set to any value, it is not evaluated
The above-mentioned parameters are selectable dependent on configuration setting
and installed expansion module.
Note: Some applications require two speed sensors. Parameter Actual Speed Source
766 must be set to the motor speed sensor for motor control. The other
speed sensor is used external. Comply with the application manuals “Elec-
tronic gear” and “Positioning”.
7.4.1 Speed sensor 1

Connect the speed sensor tracks to the digital inputs S5IND (track A), S4IND (track B)
and S6IND (track Z).
The speed sensor type and the evaluation required are adjusted via the Operation
Mode 490 of speed sensor 1.
For a detailed description of possible settings refer to section 9.4.
Parameter Settings
No. Description Min. Max. Fact.
490 Operation Mode speed sensor 1 Selection
491 Division Marks speed sensor 1 1 8192 1024
Note: Dependent on the Operation Mode 490 of speed sensor 1 the digital inputs
S4IND, S5IND and S6IND are disabled for other functions. The functions will
not be evaluated.
80 80 Operating
7.4.2 Speed sensor 2
Speed sensor 2 must be connected to an expansion module. For connection, functions
and detailed parameter description refer to the applicable operation instructions man-
ual of the expansion module.
Parameter Settings
No. Description Min. Max. Fact.
493 Operation Mode speed sensor 2 Selection
494 Division Marks speed sensor 2 1 8192 1024
495 Level Selection
The parameters 493, 494 and 495 are selectable dependent on the installed expan-
sion module.
Note: Dependent on the Operation Mode 493 of speed sensor 2 some digital inputs
of the expansion module are disabled for other functions. The functions will
not be evaluated.

7.5 Set-up via the Communication Interface
Parameter-setting and commissioning of the frequency inverter via one of the optional
communication interfaces include the plausibility check and the parameter identifica-
tion functions. The parameters can be adjusted by qualified users. The parameter
selection during the guided commissioning procedure includes the basic parameters.
These are based on standard applications of the corresponding configuration and are
therefore useful for commissioning.
Caution! Parameter settings may only be changed by qualified staff. Before starting
the commissioning process, read the documentation carefully and comply
with the safety instructions.
The parameter SETUP Selection 796 defines the function which is carried out directly
after the selection (if controller release signal is present at digital input S1IND). The
operation modes include functions which are also carried out automatically one after
the other during the guided commissioning procedure.
SETUP Selection 796 Function

0 - Clear Status The auto set-up routine does not perform a function
The warning message is acknowledged and the auto set-up
1 - Continue
routine is continued.
The auto set-up routine is stopped and a RESET of the fre-
2 - Abort
quency inverter is performed.
The auto set-up routine is performed in data set 0 and the
Complete Setup,
10 - parameter values are stored in all of the four data sets iden-
DS0
tically.
Complete Setup, The parameter values of the auto set-up are stored in data
11 -
DS1 set 1.
12 -
DS2 set 2.
13 -
DS3 set 3.
14 -
DS4 set 4.
Check Machine The auto set-up routine checks the rated motor parameters
20 -
Data, DS0 in the four data sets.
Check Machine The rated motor parameters in data set 1 are checked for
21 -
Data, DS1 plausibility.
22 -
23 -
24 -
The auto set-up routine determines extended motor data via
Calculation and the parameter identification feature, calculates dependent
30 -
Para-Ident., DS0 parameters and stores the parameter values in all of the four
data sets identically.
Calculation and Further motor data are measured, dependent parameters are
31 -
Para-Ident., DS1 calculated and the parameter values are saved in data set 1.
32 -
33 -
34 -
82 82 Operating
The individual steps of the auto set-up routine can be monitored and checked via pa-
rameter SETUP Status 797. The setup routine via the communication interface continu-
ously updates the status parameter which can be read out via the interface.
Status Messages
Message Meaning
Ok Auto set-up routine has been carried out.
PC Phase 1 The plausibility check of the motor data is active.
PC Phase 2 The calculation of dependent parameters is active.
The parameter identification requires a controller release
S1IND
signal at digital input S1IND.
The rated motor values are checked by the parameter identi-
Parameter identification
fication feature.
Setup already active The setup routine via the control unit is being carried out.
The parameter identification requires a controller release
No release signal
signal at digital input S1IND.
Error Error during the auto set-up routine.
Warning The parameter identification feature diagnosed an unbalance
phase asymmetry during the measurements in the three motor phases.
Warning Messages
Code Message Meaning
The value of the parameter Rated voltage 370 is out of the
Rated rated voltage range of the frequency inverter. The maximum
SA0001
Voltage reference voltage is indicated on the rating plate of the fre-
quency inverter.
For a three-phase motor, the calculated efficiency is in the
limit range. Check and correct, if necessary, the values en-
SA0002 Efficiency
tered for the parameters Rated voltage 370, Rated current
371 and Rated power 376.
Rated The value entered for parameter Rated cos phi 374 is out-
SA0003
Cos Phi side of the normal range (0.6 to 0.95). Correct the value.
For three-phase motor, the calculated slip is in the limit
Slip
SA0004 range. Check and, if necessary, correct Rated speed 372 and
Frequency
Rated frequency 375.
Error Messages
Code Message Meaning
Rated cur- The value entered for parameter Rated current 371 is too
SF0001
rent too low low. Correct the value.
Rated cur- The value for parameter Rated current 371 is too high, re-
SF0002 rent too ferred to parameters Rated power 376 and Rated voltage
high 370. Correct the values.
Rated Cos The value entered for parameter Rated cos phi 374 is wrong
SF0003
Phi (greater than 1 or smaller than 0.3). Correct the value.
The calculated slip frequency is negative. Check and, if nec-
Negative slip
SF0004 essary, correct the values entered for parameters Rated
frequency
speed 372 and Rated frequency 375.
Slip The calculated slip frequency is too high. Check and, if nec-
SF0005 frequency essary, correct the values entered for parameters Rated
too large speed 372 and Rated frequency 375.
The calculated total output of the drive is lower than the
Output
SF0006 rated power. Correct and check, if necessary, the value en-
balance
tered for parameter Rated power 376.
Config. not The set configuration is not supported by the auto set-up
SF0007
supported routine.

8 Inverter Data
The series ACT frequency inverters are suited for a wide range of applications. The
modular hardware and software structure enables customer-specific adaptation. The
available hardware functionality of the frequency inverter is displayed in the control
unit and the optional control software VPlus. The software parameters can be ad-
justed to meet the requirements of the specific application.
8.1 Serial Number

The Serial Number 0 is entered on the nameplate during the fabrication of the fre-
quency inverter. Information on the device type and the fabrication data (8-digit
number) are indicated. Additionally, the serial number is printed on the nameplate.
Serial number 0 : ACT 401 – 09 ; 04102013

Nameplate: Type: ACT 401 – 09 ; Serial No.: 04102013
8.2 Optional Modules

Modular extension of the hardware is possible via the plug-in slots. The Optional
modules 1 detected by the frequency inverter and the corresponding designations of
the modules are displayed on the control unit and in the optional control software
VPlus after initialization. For the parameters required for the expansion module, refer
to the corresponding operating instructions.
CM-232 ; EM-IO-01
8.3 Inverter Software Version

The firmware stored in the frequency inverter defines the available parameters and
functions of the software. The software version is indicated in parameter Inverter
software version 12. In addition to the version, the 6-digit software key is printed on
the name plate of the frequency inverter.
Inverter software version 12 : 4.2.3

Nameplate: Version: 4.2.3 ; Software: 140 012
8.4 Set Password

As a protection against unauthorized access, the parameter Set password 27 can be
set such that anyone who wants to change parameters must enter this password be-
fore. A change of parameter is only possible if the password in entered correctly. If
the Set password 27 parameter is set to zero, no password is required for access to
the parameters. The previous password is deleted.
Parameter Settings
27 Set Password 0 999 0
84 84 Operating
8.5 Control Level
The Control level 28 defines the scope of the functions to be parameterized. The
operating instructions describe the parameters on the third control level. These pa-
rameters should only be set by qualified users.
Parameter Settings
28 Control Level 1 3 1
8.6 User Name

The User name 29 can be entered via the optional control software VPlus. The plant
or machine designation cannot be displayed completely via the control unit.
32 alpha-numerical characters
8.7 Configuration
The Configuration 30 determines the assignment and basic function of the control
inputs and outputs as well as the software functions. The software of the frequency
inverters offers various configuration options. These differ with respect to the way in
which the drive is controlled. Analog and digital inputs can be combined and comple-
mented by optional communication protocols. The operating instructions describe the
following configurations and the relevant parameters in the third Control level 28
(adjustment of parameter Control level 28 to value 3).
Configuration 110, sensorless control

the V/f characteristic in accordance with the voltage/frequency ratio.
Configuration 111, sensorless control with technology controller

Configuration 111 extends the functionality of the sensor-less control by software
functions for easier adaptation to the customer's requirements in different applica-
tions. Depending on the application, the technology controller may be used, which
enables the control of flow rate, pressure, contents level or speed.

Configuration 410 contains the functions for sensor-less, field-oriented control of a
3-phase machine. The current motor speed is determined from the present currents
and voltages in combination with the machine parameters. In this configuration, par-
allel connection of several 3-phase motors is possible to a limited extent only.

with Technology Controller
Controller, which enables the control of flow rate, pressure, contents level or speed

with speed/torque control
Configuration 210, field-oriented control

Configuration 211, field-oriented control with technology controller

Controller, which enables the control of flow rate, pressure, contents level or speed.
Configuration 230, field-orientated control with speed/torque control


In the table, you will find a list of functions which are available in the different configurations.
Configuration
V/f - charac-
field-oriented control
teristic
sensorless sensorless sensor
Function Chapter 110 111 410 411 430 210 211 230
Speed control 16.5.3 x x x x x
Torque control 16.5.2 x x
Switch-over speed/torque con-
14.4.6 x x
trol
Dynamic Voltage Pre-Control 15.1 x x
Intelligent current limits 16.1 x x x x x x x x
Voltage controller 16.2 x x x x x x x x
Technology controller: 16.3 x x x
− pressure control 16.3 x x x
− flow rate control 16.3 x x x
− Contents level control 16.3 x x x
− Speed control 16.3 x x x
Slip compensation 16.4.1 x
Current limit value controller 16.4.2 x x
Current Controller 16.5.1 x x x x x x
Limit Value Sources 16.5.2.1 x x x x x x
Acceleration Pre-Control 16.5.4 x x x x x x
Field Controller 16.5.5 x x x x x x
Modulation Controller 16.5.6 x x x x x x
Starting behavior: 11.1 x x x x x x x x
− Starting current impression 11.1.1.1 x x x x x
− Flux Formation 11.1.2 x x x x x x
Stopping behavior: 11.2 x x x x x x x x
− Direct current brake 11.3 x x
Auto Start 11.4 x x x x x x x x
Search Run 11.5 x x x x x x x x
Reference point positioning 11.6.1 x x x
Axle Positioning 11.6.2 x
Frequency Reference Channel 13.4 x x x x x
Reference percentage channel 13.5 x x x x x
Fixed Frequencies 13.6.1 x x x x x x x
Fixed Percentages 13.6.3 x x x x x
Block Frequencies 13.9 x x x x x x x
Repetition frequency input 13.11 x x x x x x x x
Brake Chopper 17.4 x x x x x x x x
Motor Circuit Breaker 17.5 x x x x x x x x
V-belt Monitoring 17.6 x x x x x x x x
Motor Chopper 17.7.1 x x x x x x
Temperature Adjustment 17.7.2 x x x x x x
Encoder Monitoring 17.7.3 x x x

8.8 Language
The parameters are stored in the frequency inverter in various languages. The pa-
rameter description is displayed in the selected Language 33, e.g. by the PC program
VPlus,.
Language 33 Function
0 - Deutsch Parameter description in German.
1 - English Parameter description in English.
2 - Italiano Parameter description in Italian.
8.9 Programming
The parameter Program(ming) 34 enables acknowledgment of a fault message and
resetting to the factory settings. The display of the control unit reads "dEFLt" or "rE-
SEt" and the LEDs indicate the status of the frequency inverter.
Program(ming) 34 Function
The KP 500 control unit is prepared for parameter trans-
111 - Parameter transfer mission. A connected frequency inverter can receive data
from the control unit.
110 - Normal mode Reset the KP 500 control unit to standard mode.
The current error message can be acknowledged via
123 - RESET digital input S1IND or the software parameter. The dis-
play of the control unit reads "rESEt".
The parameters of the selected configuration are over-
4444 - Default written - except for a few exceptions - by the default
settings. The display of the control unit reads "dEFLt".
Note: The parameters Control Level 28, Language 33 as well as Configura-

tion 30 are not changed during the reset to the default settings (Pro-
gram(ing) 34 = 4444).
88 88 Operating
9 Machine Data
The input of the machine data is the foundation for the functionality of the control
functions and methods. In the course of the guided commissioning, the necessary
parameters are inquired according to the selected Configuration 30.
9.1 Rated Motor Parameters

Set the rated parameters of the three-phase asynchronous machine according to the
name plate or the data sheet of the motor. The default settings of the machine pa-
rameters are based on the nominal data of the frequency inverter and the corre-
sponding four-pole three-phase motor. The machine data required for the control
functions and methods are checked for plausibility and calculated in the course of the
commissioning.
The user should check the rated values specified by default.
Parameter Settings
370 Rated Voltage 0.17⋅UFIN 2⋅UFIN UFIN
371 Rated Current 0.01⋅IFIN 10⋅o ⋅ IFIN IFIN
372 Rated Speed 96 min-1 60 000 min-1 nN
373 No. of Pole Pairs 1 24 2
374 Rated cosine (ϕ) 0.01 1.00 cos(ϕ)N
375 Rated Frequency 10.00 Hz 1000.00 Hz 50.00
376 Rated mechanical power 0.01⋅PFIN 10⋅PFIN PFIN
In the case of three-phase machines, the speed can be increased at a constant torque
if the motor winding can be switched over from star to delta connection. The change-
over results in a change of the dependent parameters by a factor of square root of 3.
Attention! The rated data of the motor are to be entered according to the specifi-
cations on the rating plate for the motor connection type used (star or
delta connection). If the data entered deviate from the rating plate, the
parameters will not be identified correctly. Parameterize the rated data
according to the specifications for the motor winding connection indi-
cated on the rating plate. Take the higher rated current of the con-
nected asynchronous motor into account.

9.2 Further motor parameters
In particular the field-oriented control requires the determination of further data which
cannot be read off the name plate of the 3-phase machine for the precise calculation
of the machine model. In the course of the guided commissioning, the parameter
identification was carried out to measure the further motor parameters.
9.2.1 Stator Resistance

The resistance of the stator winding was measured during the guided commissioning.
The measured value is stored as a phase value in parameter Stator resistance 377
and is 3 times smaller than the winding resistance in delta connection.
By default, the equivalent stator resistance of a standard motor is entered to match
the nominal power of the frequency inverter.
Parameter Settings
377 Stator Resistance 0 mΩ 65535 mΩ RsN
The stator resistance can be optimized while the machine is in no-load operation. At
the steady-state operating point, the torque-forming current Isq 216 and/or the esti-
mated Active current 214 should be zero. Due to the temperature-dependent of the
stator resistance, the adjustment should be done at a winding temperature which is
also reached during normal operation.
A correct measurement will optimize the control functions.
9.2.2 Leakage Coefficient

The leakage coefficient of the machine defines the ratio of the leakage inductivity to
the main inductivity. The torque and flux-forming current components are thus cou-
pled via the leakage coefficient. Optimization of the leakage coefficient within the
field-orientated control systems requires acceleration to various operating points of
the drive. Unlike the torque-forming current Isq 216, the flow-forming current Isd
215 should be largely independent of the load torque. The flow-forming current com-
ponent is inversely proportional to the leakage coefficient. If the leakage coefficient is
increased, the torque-forming current increases and the flux-forming component
drops. The adjustment should result in a relatively constant actual current Isd 215,
matching the parameter Rated magnetizing current 716, regardless of the load on the
drive.
The sensorless control system uses the parameter Leakage coefficient 378 in order to
optimize the synchronization to one drive.
Parameter Settings
378 Leakage Coeff. 1.0 % 20.0 % 7.0 %
90 90 Operating
9.2.3 Magnetizing Current
The Rated magnetizing current 716 is a measure of the flux in the motor and thus of
the voltage which is present at the machine in no-load condition depending on the
speed. The guided commissioning determines this value at about 30% of the Rated
current 371. This current can be compared to the field current of an externally ex-
cited direct current machine.
In order to optimize the sensor-less field-oriented control system, the machine has to
be operated without load at a rotational frequency which is below the Rated frequency
375. The accuracy of the optimization increases with the adjusted Switching fre-
quency 400 and when the drive is in no-load operation. The flux-forming actual cur-
rent value Isd 215 to be read out should roughly match the set Rated magnetizing
current 716.
The field-orientated control with speed sensor feedback uses the parameterized Rated
magnetizing current 716 for the flux in the motor.
The dependence of the magnetizing on the frequency and voltage at the correspond-
ing nominal operating point in question is taken into account by a magnetizing charac-
teristic. The characteristic is calculated via three points, in particular in the field weak-
ening range above the rated frequency. The parameter identification has determined
the magnetizing characteristic of the motor and set the parameters Magnetizing cur-
rent 50% 713, Magnetizing current 80% 713 and Magnetizing current 110% 713.
Parameter Settings
713 Magnetizing current 50% Flux 1.00% 50.00% 31.00%
716 Rated Magnetizing Current 0.01⋅IFIN o ⋅ IFIN 0.3⋅IFIN
9.2.4 Rated Slip Correction Factor

The rotor time constant results from the inductivity of the rotor circuit and the rotor
resistance. Due to the temperature-dependence of the rotor resistance and the satu-
ration effects of the iron, the rotor time constant is also dependent on temperature
and current. The load behavior and thus the rated slip depend on the rotor time con-
stant. The guided commissioning determines the machine data during the parameter
identification and sets the parameter Rated slip correction factor 718 accordingly. For
the fine adjustment or a check of the rotor time constant, proceed as follows: Load
the machine at fifty percent of the Rated frequency 375. As a result, the voltage must
be approximately fifty percent of the Rated voltage 370, with a maximum tolerance of
5 %. If this is not the case, the correction factor must be changed accordingly. The
larger the correction factor is set, the stronger the voltage drop when the machine is
loaded. The value calculated by the rotor time constants can be read out via the ac-
tual value Current rotor time constant 227. The adjustment should be done at a
winding temperature which is also reached during normal operation of the motor.
Parameter Settings
718 Rated Slip Correction Factor 0.01% 300.00% 100.00%

9.3 Internal values
The following parameters are used for the internal processing of motor data. An ad-
justment is not necessary.
Parameter Parameter
No. Description No. Description
368 Internal value 01 705 Internal value 08
9.4 Speed sensor 1

The frequency inverters are to be adapted to the application depending on the re-
quirements. A part of the available Configurations 30 demand continuous measure-
ment of the actual speed for the control functions and methods. The necessary con-
nection of an incremental speed sensor is done on the digital control terminals S5IND
(track A) and S4IND (track B) of the frequency inverter.
9.4.1 Operation mode speed sensor 1

Operation mode speed sensor 1 490 can be selected according to the connected in-
cremental speed sensor. A unipolar speed sensor is to be connected to the standard
control terminals.

Speed measurement is not active; the digital inputs
0 - Off
are available for other functions.
Two-channel speed sensor with recognition of direc-
1 – Single Evaluation tion of rotation via track signals A and B;
one signal edge is evaluated per division mark.
Two-channel speed sensor with recognition of direc-
Quadruple
4– tion of rotation via track signals A and B;
evaluation
four signal edges are evaluated per division mark.
One-channel speed sensor via track signal A; the ac-
Single evaluation tual speed value is positive. One signal edge is evalu-
11 –
without sign ated per division mark. The digital input S4IND is
available for further functions.
One-channel speed sensor via track signal A; the ac-
Double evaluation tual speed value is positive. Two signal edges are
12 –
without sign evaluated per division mark. The digital input S4IND is
available for further functions.
Same as in operation mode 1. The actual speed value
Single evaluation
101 – is inverted. (Alternative to exchanging the track sig-
inverted
nals)
Same as in operation mode 4. The actual speed value
Quadruple evalua-
104 – is inverted. (Alternative to exchanging the track sig-
tion inverted
nals)
Single evaluation Same as operation mode 11. The actual speed value is
111 –
negative negative.
Double evaluation Same as operation mode 12. The actual speed value is
112 –
negative negative.
92 92 Operating
Attention! In configurations 210, 211 and 230, digital input S4IND is by default set
for the evaluation of a speed sensor signal (track B).
If an operation mode without sign is selected (Operation Mode 11 or
Operation Mode 12), this input is not set for the evaluation of a speed
sensor signal and can be used for other functions.
9.4.2 Division marks, speed sensor 1

The number of increments of the connected speed sensor can be adjusted via parame-
ter Division marks, speed sensor 1 491. Select the division marks of the speed sensor
according to the speed range of the application.
The maximum number of division marks Smax is defined by the frequency limit of
fmax=150 kHz of the digital inputs S5IND (track A) and S4IND (track B).
60 s / min
Smax = 150000 Hz ⋅
n max fmax = 150000 Hz
For example: nmax = Max. speed of the motor in RPM
60s
S = 150000 Hz ⋅ = 6000
max 1500
To guarantee true running of the drive, an encoder signal must be evaluated at least
every 2 ms (signal frequency f = 500 Hz). The minimum number of division marks Smin
of the incremental encoder for a required minimum speed nmin can be calculated from
this requirement.
60 s / min
Smin = 500 Hz ⋅ nmin = Min. speed of the motor in RPM
A ⋅ n min A = Evaluation (1, 2, 4)
For example:
60 s
S = 500 Hz ⋅ = 1500
min 2 ⋅10
Parameter Settings
491 Division marks, speed sensor 1 1 8192 1024

10 System Data
The various control functions and methods according to the selected Configura-
tion 30 are supplemented by control and special functions. For monitoring the appli-
cation, process parameters are calculated from electrical control parameters.
10.1 Actual Value System

The parameter Factor Actual Value System 389 can be used if the drive is monitored
via the parameter Actual Value System 242.
The Actual Frequency 241 to be monitored is multiplied by the Factor Actual Value
System 389 and can be read out via the parameter Actual Value System 242, i.e.
Actual Frequency 241 x Factor Actual Value System 389 = Actual Value Sys-
tem 242.
Parameter Settings
389 Factor Actual Value System -100.000 100.000 1.000
10.2 Volume Flow and Pressure

The parameterization of the factors Nominal Volumetric Flow 397 and Nominal
Pressure 398 is necessary if the matching actual values Volumetric flow 285 and
Pressure 286 are used to monitor the drive. The conversion is done using the electri-
cal control parameters.
Volume Flow 285 and Pressure 286 are referred to the Effective Current 214 in the
case of the sensor-less control methods. In the case of the field-oriented control
methods, they are referred to the torque-forming current component Isq 216.
Parameter Settings
397 Nominal Volumetric Flow 1 m3/h 99999 m3/h 10 m3/h
398 Nominal Pressure 0.1 kPa 999.9 kPa 100.0 kPa
Line mains or channel characteristic:
H
kPa B1 Pconst.- method
A
bad point method

B2
Q
m /h
3
Point A in the figure describes the rating point of a pump. The transition to partial
load operation mode B1 can be effected at a constant pressure H (change of convey-
ing flow Q, pressure H remains constant). The transition to partial load operation
mode B2 can be effected according to the bad point method (change of pressure H
and conveying flow Q). Both methods can be realized with the integrated technology
controller in configurations 111 and 211. The actual values displayed are calculated
according to the bad point method independently of the selected Operation
Mode 440 of the technology controller.

11 Operational Behavior
The operational behavior of the frequency inverter can be adjusted to the application
by setting the parameters appropriately. In particular the starting and stopping behav-
ior can be selected according to the selected Configuration 30. Additionally, features
such as Auto Start, synchronization and positioning functions facilitate the integration
in the application.
11.1 Starting Behavior

The start of the 3-phase machine can be parameterized in accordance with the control
functions and methods. In contrast to the sensor-less control method, the field-
oriented control methods only require the definition of the limit values Max. Flux For-
mation Time 780 and Current during Flux Formation 781 for the adjustment of the
starting behavior. The acceleration behavior of the sensor-less control method in con-
figurations 110 and 111 can be selected as described in the following chapter.
11.1.1 Starting Behavior of Sensorless Control System

The parameter Operation Mode 620 for the starting behavior is available in configu-
rations 110 and 111. Depending on the operation mode selected, the machine is mag-
netized first or a starting current is impressed. The voltage drop across the stator
resistance which reduces the torque in the lower frequency range can be compen-
sated by the IxR compensation.
To ensure the correct function of the IxR compensation, the stator resistance is de-
termined during the guided commissioning. The IxR compensation is only activated
after the stator resistance was determined correctly.
Operation Mode 620 Starting Behavior

At the start the voltage with the th value of parameter
Starting Voltage 600 is set at an output frequency of
0 Hz. After this, the output voltage and the output fre-
quency are changed according to the control method.
0 - Off
The break-away torque and the current at the start is
determined by the adjusted starting voltage. It may be
necessary to optimize the starting behavior via the pa-
rameter Starting Voltage 600.
In this operation mode, the Current during Flux-
Formation 781 for magnetization is impressed into the
motor after release. The output frequency is kept at zero
1 - Magnetization
Hz for the Maximum Flux-Formation Time 780. After
this time has expired, the output frequency follows the
adjusted V/f characteristic. (see operation mode 0- Off)
Operation mode 2 includes operation mode 1. After the
Maximum Flux-Formation Time 780 has elapsed, the
output frequency is increased according to the set accel-
eration. If the output frequency reaches the value set
Magnetization +
2- with the parameter Frequency Limit 624, the Starting
current impression
Current 623 is withdrawn. There is a smooth transition
to 1.4 times the frequency limit to the set V/f characteris-
tic. As from this operating point, the output current de-
pends on the load.
Table "Operation Modes for Starting Behavior" continued on next page.

Operation mode Starting Behavior
Operation mode 3 includes operation mode 1 of the start
function. When the output frequency reaches the value
Magnetization + set with parameter Frequency Limit 624, the increase of
3-
IxR compensation the output voltage by the IxR compensation becomes
effective. The V/f characteristic is displaced by the portion
of voltage which depends on the stator resistance.
In this operation mode, the current set with the parame-
ter Current during Flux-Formation 781 is impressed into
the motor for magnetization after release. The output
frequency is kept at zero Hz for the Maximum Flux-
Formation Time 780. After the time has elapsed, the
output frequency is increased according to the set accel-
Magnetization + eration. If the output frequency reaches the value set
4 - current imp. + IxR with the parameter Frequency Limit 624, the Starting
compensation Current 623 is withdrawn. There is a smooth transition
to the V/f characteristic, and a load-dependent output
current is obtained. At the same time, the increase of the
output voltage by the IxR compensation becomes effec-
tive as from this output frequency. The V/f characteristic
is displaced by the portion of voltage which depends on
the stator resistance.
Operation mode 12 contains an additional function to
guarantee a starting behavior under heavy duty condi-
tions. The magnetization and starting current impression
Magnetization + are done according to operation mode 2. The ramp stop
12 - current imp. w. takes the current consumption of the motor at the corre-
ramp stop sponding operating point into account and controls the
frequency and voltage change by stopping the ramp. The
Controller Status 275 signals the intervention of the con-
troller by displaying the message “RSTP“.
In this operation mode, the functions of operation mode
12 are extended by the compensation of the voltage drop
across the stator resistance. When the output frequency
Magnetization +
reaches the value set with parameter Frequency Limit
14 - current imp. w. r.
624, the increase of the output voltage by the IxR com-
+ IxR comp.
pensation becomes effective. The V/f characteristic is
displaced by the portion of voltage which depends on the
stator resistance.
In contrast to field-oriented control systems, sensor-less control systems feature a

current controller which controls the starting behavior. The PI controller checks the
current impression by parameter Starting Current 623. The proportional and integrat-
ing parts of current controller can be adjusted via parameters Amplification 621 and
Integral Time 622, respectively. The control functions can be deactivated by setting
the parameters to 0.
Parameter Settings
621 Amplification 0.01 10.00 1.00
622 Integral Time 1 ms 30000 ms 50 ms
96 96 Operating
11.1.1.1 Starting Current
Configurations 110, 111 and 410, 411 and 430 for control of a 3-phase machine use
the starting current impression in operation modes 2, 4, 12 and 14 for the parameter
Operation Mode 620. The Starting Current 623 guarantees, in particular for heavy
starting, sufficient torque until the Frequency Limit 624 is reached.
Applications in which high current is permanently needed at a low speed are to be
realized using forced-ventilated motors for thermal reasons.
Parameter Settings
623 Starting Current 0.0 A o ⋅ IFIN IFIN
11.1.1.2 Frequency Limit

The Starting current 623 is impressed in configurations 110, 111, 410, 411 and 430
for control of a 3-phase machine until the Frequency Limit 624 is reached. Permanent
operating points below the frequency limit are only admissible if forced-ventilated mo-
tors are used. The transition to the control method of the selected configuration 30
takes place above the frequency limit.
Parameter Settings
624 Frequency Limit 0.00 Hz 100.00 Hz 2.60 Hz
11.1.2 Flux Formation

Field-oriented control in the configurations 210, 211, 230, 410, 411 and 430 are based
on separate regulation of the flux-forming and torque-forming current components.
Upon startup, the machine is magnetized and a current is impressed first. With the
parameter Current during Flux-Formation 781 the magnetization current Isd is set,
with the parameter Maximum Flux-Formation Time 780 the maximum time for the
current impression is set.
The current impression is done until the reference value of the rated magnetizing cur-
rent is reached or the Maximum Flux-Formation Time 780 is exceeded.
Parameter Settings
300 ms 1)
780 Maximum Flux-Formation Time 1 ms 10000 ms
1000 ms 2)
781 Current during Flux Formation 0.1⋅IFIN o ⋅ IFIN IFIN
The factory setting of parameter Maximum flux formation time 780 depends on the setting of
parameter Configuration 30:
1)
configurations 1xx
2)
configurations 2xx / 4xx

11.2 Stopping Behavior
The stopping behavior of the three-phase machine can be defined via parameter Op-
eration Mode 630. Via the digital logic signals Start Clockwise 68 and Start Anti-
clockwise 69, stopping is activated. By combining the logic signals which are assigned
to the digital inputs by default, the stopping behavior can be selected from the follow-
ing table.
Stopping Behavior
Start Clockwise = 0 and Start Anticlockwise = 0
Stopping behavior 0
Stopping behavior 1
Stopping behavior 2
Stopping behavior 3
Stopping behavior 4
Stopping behavior 5
Stopping behavior 6
Stopping behavior 7
Operation Mode 630
Stopping behavior 0
0 1 2 3 4 5 6 7
(Free stopping)
Start Clockwise = 1 and Start Anticlockwise = 1
Stopping behavior 1
(Stop 10 11 12 13 14 15 16 17
and Switch off)
Stopping behavior 2
(Stop 20 21 22 23 24 25 26 27
and Hold)
Stopping behavior 3
(Stop 30 31 32 33 34 35 36 37
and DC brakes)
Stopping behavior 4
(Emergency Stop 40 41 42 43 44 45 46 47
and Switch off)
Stopping behavior 5
(Emergency Stop 50 51 52 53 54 55 56 57
and Hold)
Stopping behavior 6
(Emergency Stop 60 61 62 63 64 65 66 67
and Brake)
Stopping behavior 7
70 71 72 73 74 75 76 77
(DC brakes)
Operation Mode 630 of the stopping behavior is to be parameterized according to the

matrix. The selection of the operation modes can vary according to the control method
and the available control inputs.
Example: The machine is to stop according to stopping behavior 2 if the digital logic
signals Start Clockwise 68 = 0 and Start Anticlockwise 69 = 0.
Additionally, the machine is to stop according to stopping behavior 1 if the digital logic
signals Start Clockwise 68 = 1 and Start Anticlockwise 69 = 1.
To achieve this, the parameter Operation Mode 630 must be set to 12.
By selecting the stopping behavior you also select the control of a mechanical brake if
operation mode „41- Open brake“ is used for one digital output for controlling the
brake.
98 98 Operating
Stopping Behavior
Stopping behavior 0
The inverter is disabled immediately. The drive deener-
gized immediately and coasts freely.
Free stopping
The drive is brought to a standstill at the set deceleration.
As soon as the drive is at a standstill, the inverter is dis-
Stopping behavior 1 abled after a holding time. The holding time can be set via
the parameter Holding Time 638.
Stop Depending on the setting of the parameter Starting Func-
+ Switch off tion 620, the Starting Current 623 is impressed or the
Starting Voltage 600 is applied for the duration of the
holding time.
The drive is brought to a standstill at the set deceleration
Stopping behavior 2 and remains permanently supplied with current.
Depending on the setting of the parameter Starting func-
Stop + Hold tion 620, the Starting Current 623 is impressed as from
standstill or the Starting Voltage 600 is applied.
The drive is brought to a standstill at the set deceleration.
As from standstill, the direct current set via parameter
Stopping behavior 3 Braking Current 631 is impressed for the Braking Time
632.
Stop + DC brakes Comply with the notes in chapter "DC brake".
Stopping behaviors 3, 6 and 7 are only available in the
configurations for sensor-less control.
The drive is brought to a standstill at the emergency stop
deceleration. As soon as the drive is at a standstill, the
Stopping behavior 4 inverter is disabled after a holding time.
The holding time can be set via the parameter Holding
Emergency stop Time 638. Depending on the setting of the parameter
+ switch off Starting Function 620, the Starting Current 623 is im-
pressed as from standstill or the Starting Voltage 600 is
applied.
The drive is brought to a standstill at the set emergency
Stopping behavior 5 stop deceleration and remains permanently supplied with
current.
Emergency stop + Depending on the setting of the parameter Starting Func-
Hold tion 620, the Starting Current 623 is impressed as from
standstill or the Starting Voltage 600 is applied.
The drive is brought to a standstill at the set emergency
stop deceleration. As from standstill, the direct current set
Stopping behavior 6
via parameter Braking Current 631 is impressed for the
Braking Time 632.
Emergency stop +
Comply with the notes in chapter "DC brake".
Brake
Direct current braking is activated immediately. The direct
current set with the parameter Braking Current 631 is
Stopping behavior 7
impressed for the die Braking Time 632.
Comply with the notes in chapter "DC brake".
Direct current brake
Comply with the notes for controlling a mechanical brake in chapter 14.3.4 Open
brake.

11.2.1 Switch-Off Threshold
The Switch-off Threshold Stop Function 637 defines the frequency as from which a
standstill of the drive is recognized. This percentage parameter value is applied to the
set Maximum Frequency 419.
The switch-off threshold is to be adjusted according to the load behavior of the drive
and the device output, as the drive must be controlled to a speed below the switch-off
threshold.
Parameter Settings
637 Switch-Off Threshold 0.0 % 100.0 % 1.0 %
Attention! If the motor builds up a stopping torque, it may be possible that the
switch-off threshold stop function is not reached due to the slip fre-
quency and the standstill of the drive is not recognized. In this case,
increase the value of the Switch-off Threshold Stop Function 637.
11.2.2 Holding Time

The Holding Time Stop Function 638 is considered in stopping behaviors 1, 3, 4 and
6. Controlling to zero speed results in the motor heating up and should only be done
for a short period in the case of internally ventilated motors.
Parameter Settings
638 Holding Time 0.0 s 200.0 s 1.0 s
11.3 Direct current brake

Stopping behaviors 3, 6, 7 and the search run function include the direct current brake.
Depending on the setting of the stop function, a direct current is impressed into the
motor either directly or, when it is at a standstill, after the demagnetization time. The
impression of the Braking current 631 results in the motor heating up and should only
be done for a short period in the case of internally ventilated motors.
Parameter Settings
631 Braking Current 0.00 A √2⋅IFIN √2⋅IFIN
The setting of the parameter Braking Time 632 defines the time-controlled stopping
behavior. Contact-controlled operation of the direct current brake is activated by enter-
ing the value zero for the Braking Time 632.
Time controlled:
The direct current brake is controlled by the status of signals Start clockwise and Start
anticlockwise. The current set by the parameter Braking Current 631 flows until the
time set by the parameter Braking Time 632 has expired. During the braking time the
status of both signals Start clockwise and Start anticlockwise are logical 0 (low) or
logical 1 (high).

Operating ACTIVE
Contact-controlled:
If the parameter Braking Time 632 is set to the value 0.0 s, the direct current brake is
controlled by the Start clockwise and Start anticlockwise signals. The time monitoring
and limitation by Braking Time 632 are deactivated. The braking current flows up to
the logical status 0 (low) of the controller release (S1IND).
Parameter Settings
632 Braking Time 0.0 s 200.0 s 10.0 s
To avoid current surges, which can possibly lead to a fault switch-off of the frequency
inverter, a direct current may only be impressed into the motor after the motor has
been demagnetized. As the demagnetization time depends on the motor used, it can
be set with the parameter Demagnetizing Time 633.
The selected demagnetizing time should be approximately three times the Act. Rotor
Time Constant 227.
Parameter Settings
633 Demagnetizing Time 0.1 s 30.0 s 5.0 s
The selected stopping behavior is supplemented by a current controller to control the

direct current brake. The PI controller checks the current impression of the set Brak-
ing Current 631. The proportional and integrating parts of current controller can be
adjusted via parameters Amplification 634 and Integral Time 635, respectively. The
control functions can be deactivated by setting the parameters to 0.
Parameter Settings
634 Amplification 0.00 10.00 1.00
11.4 Auto Start

The Auto Start function is suitable for applications which permit a start at mains volt-
age by their function. By activation of the auto-start function via parameter Operation
Mode 651, the frequency inverter accelerates the drive after connection of the mains
voltage. The controller release signal and the start command are necessary according
to the regulations. When the motor is switched on, it is accelerated according to the
parameterization and the reference value signal.

The drive is accelerated, after application of the mains
voltage, as soon as the controller enabling signal and the
0 - Off
start command are switched from stop to start (edge
evaluation).
The drive is accelerated by the frequency inverter as soon
1 - Switched on
as the mains voltage is applied (level evaluation).
Warning! Comply with standard EN 60204 and VDE provision 0100 part 227 and
provision 0113, in particular Sections 5.4, protection against automatic
restart after main line voltage failure and voltage recovery, and Section
5.5, undervoltage protection.
Appropriate measures must be taken to exclude any risk for staff, ma-
chines and production goods.
In addition to that, all specific regulations relevant to the application as
well as all national directives are to be complied with.

Operating ACTIVE
11.5 Search Run
The synchronization to a rotating drive is necessary in applications which drive the
motor by their behavior or in which the drive is still rotating after a fault switch-off.
Via Operation Mode 645 = Search Run, the motor speed is synchronized to the cur-
rent motor speed without an "Overcurrent" fault message. After this, the motor is
accelerated to the reference speed at the set acceleration. This synchronization func-
tion determines the current rotary frequency of the drive via a search run in operation
modes 1 to 5.
The synchronization in operation modes 10 to 15 is accelerated by short test impulses.
Rotary frequencies of up to 250 Hz are determined within 100 ms to 300 ms. For
higher frequencies, a wrong frequency is determined and the synchronization fails. In
the "Quick synchronization" operation modes, the search run cannot determine
whether an synchronization attempt has failed.

0 - Off The synchronization to a rotating drive is deactivated.
The search direction is defined by the sign in front of the
reference value. If a positive reference value (clockwise
Search direction
field of rotation) is entered, the search is in a positive
1 - acc. to specified
direction (clockwise field of rotation), with a negative
reference value
reference value, the search is in a negative direction (an-
ticlockwise field of rotation).
The first attempt is to synchronize to the drive in positive
First clockwise, then
direction (clockwise field of rotation). If this attempt fails,
2 - anti-clockwise,
it is tried to synchronize to the drive in negative direction
DCB
(anticlockwise field of rotation).
The first attempt is to synchronize to the drive in negative
First anti-clockwise,
direction (anticlockwise field of rotation). If this attempt
3 - then clockwise,
fails, it is tried to synchronize to the drive in positive di-
DCB
rection (clockwise field of rotation).
Synchronization to the drive is only done in positive direc-
4 - Clockwise only, DCB
tion (clockwise field of rotation).
Anti-clockwise only, Synchronization to the drive is only done in negative di-
5-
DCB rection (anticlockwise field of rotation).
An attempt is made to synchronize to the drive in positive
Quick Synchroniza-
10 - direction (clockwise field of rotation) and in negative di-
tion
rection (anticlockwise field of rotation).
The search direction is defined by the sign in front of the
reference value. If a positive reference value (clockwise
Quick Synch. acc. to field of rotation) is entered, the search is in a positive
11 -
Preset Value direction (clockwise field of rotation), with a negative
reference value, the search is in a negative direction (an-
ticlockwise field of rotation).
Quick Sync., Clock- Synchronization to the drive is only done in positive direc-
14 -
wise Only tion (clockwise field of rotation).
Quick Sync., Anti- Synchronization to the drive is only done in negative di-
15 -
clockwise Only rection (anticlockwise field of rotation).
Operation modes 1, 4 and 5 define a direction of rotation for the search run and avoid
a deviating direction. The search run can accelerate drives by checking the rotary
frequency if the drives have a low moment of inertia and/or a small load moment.
In operation modes 10 to 15, it cannot be ruled out that a wrong direction of rotation
is determined in quick synchronization. For example, a frequency not equal to zero
may be determined although the drive is at a standstill. If there is no overcurrent, the
drive is accelerated accordingly. The direction of rotation is defined in operation
modes 11, 14 and 15.
102 102 Operating

The synchronization changes the parameterized starting behavior of the selected con-
figuration. First, the start command activates the search run in order to determine the
rotary frequency of the drive. In operation modes 1 to 5, the Current / Rated motor
current 647 is used for synchronization as a percentage of the Rated current 371.
Parameter Settings
647 Current / Rated Motor Current 1.00 % 100.00 % 70.00 %
The sensor-less control is extended for the search run by a PI-Controller, which regu-
lates the parameterized Current / Rated Motor Current 647. The proportional and
integrating part of the current controller can be set via the parameters Amplification
648 and Integral Time 649. The control functions can be deactivated by setting the
parameters to 0.
Parameter Settings
648 Amplification 0.00 10.00 1.00
If the parameter for synchronization Operation Mode 645 was set to operation mode
1 to 5 (search run), the search run is not started before the Demagnetizing Time 633
has elapsed.
If synchronization to the drive is not possible, the Braking Current 631 is impressed
into the motor in operation modes 1 to 5 for the duration of the Break.-Time after
Search Run 646. The impression of the direct current set in the parameters of the
direct current brake results in the motor heating up and should only be done for a
short period in the case of internally ventilated motors.
Parameter Settings
646 Break. Time after Search Run 0.0 s 200.0 s 10.0 s
11.6 Positioning
Positioning is done in operation mode "Reference positioning" via the definition of the
positioning distance or in operation mode "Axle positioning" via the definition of the
position angle.
Reference positioning uses a digital reference signal from a selectable signal source
for positioning the drive independent of the speed.
Axle positioning uses a digital reference signal from a speed sensor.
The function "Reference positioning" is available in configurations 110, 410 and 210
and is activated by selecting operation mode 1 for parameter Operation Mode 458.
The function "Axle positioning" is available in configuration 210 (Operation mode 210
for parameter Configuration 30) and is activated by selecting operation mode 2 for
parameter Operation Mode 458.

0 - Off Positioning switched off.
Positioning from reference point via definition of
positioning distance (rotations). The reference
1 - Reference positioning
point is acquired via a Signal Source 459.
Available in Configuration: 110, 210, 410.
Reference positioning via definition of the posi-
2 - Axle Positioning tioning angle, reference signal from speed sensor.
Available in Configuration: 210.

11.6.1 Reference Positioning
The feedback of the current position is referred to the revolutions of the motors rela-
tive to the time of the reference signal. The accuracy of the positioning for the applica-
tion to be realized is dependent on the current Actual Frequency 241, the Decelera-
tion (Clockwise) 421, the No. of Pole Pairs 373, the selected Positioning distance
460 and the parameterized control behavior.
The distance between the reference point and the required position is to be defined in
motor revolutions. The calculation of the distance covered is done with the selected
Positioning distance 460 according to the application.
The setting 0.000 U for the Positioning distance 460 causes an immediate stop of the
drive according to the selected stopping behavior for Operation Mode 630.
Parameter Settings
460 Positioning Distance 0.000 U 1000000.000 U 0.000 U
The actual value parameter Rotations 470 facilitates the setting and optimization of
the function. The revolutions of the motor displayed should correspond to the Posi-
tioning distance 460 at the required position.
The minimum number of revolutions needed until the required position is reached de-
pends on the Actual Frequency 241 and Deceleration (Clockwise) 421 (or Decelera-
tion Anticlockwise 423) as well as the No. of Pole Pairs 373 of the motor.
f2
Umin = min. number of rotations
U = f = Actual frequency 241
min 2⋅a ⋅p a = Deceleration 421 (423)
p = No. of Pole Pairs 373 of motor
Example: f = 20 Hz, a = 5 Hz/s, p = 2 ⇒ Umin = 20

At an actual frequency of 20 Hz and a deceleration of 5 Hz/s, at least 20 revolutions
are required until the drive stops at the required position. This is the minimum value
for the Positioning distance 460, a shorter positioning distance is not possible. If the
number of revolutions to the required position is to be lower, either the frequency
must be reduced, the deceleration must be increased or the reference point must be
shifted.
The digital signal for acquisition of the reference point and the logic link can be se-
lected by the parameter Signal Sources 459. The link of the digital inputs S2IND,
S3IND and S6IND to further functions is to be checked according to selected Configu-
ration 30 (e.g., in configurations 110 and 210, digital input S2IND is linked to the
function "Start of clockwise operation").
The signals for positioning and a stopping behavior should not be assigned to the same
digital input.
Signal Sources 459 Function

2 - S2IND, falling edge The positioning starts with the change of the logic
3 - S3IND, falling edge signal from 1 (HIGH) to 0 (LOW) at the reference
6 - S6IND, falling edge point.
The positioning starts with the change of the logic
1x - SxIND, rising edge
signal from 0 (LOW) to 1 (HIGH).
The positioning begins with the change of the
2x - SxIND, rising/falling edge
logic signal.
104 104 Operating

The acquisition of the reference position via a digital signal can be influenced by a
variable dead time while the control command is read and processed. The signal
propagation time is compensated by a positive value for the Signal correction 461. If
a negative signal correction is set, processing of the digital signal is delayed.
Parameter Settings
461 Signal Correction -327.68 ms +327.67 ms 0.00 ms
The influences on the positioning which depend on the operating point can be cor-
rected empirically via the parameter Load correction 462. If the required position is
not reached, the delay interval is increased by a positive load correction value. The
distance between the reference point and the required position is extended. Negative
values accelerate the braking process and reduce the positioning distance. The limit of
the negative signal correction results from the application and the Positioning distance
460.
Parameter Settings
462 Load Correction -32768 +32767 0
The behavior of the positioning after the required position of the drive is reached can
be defined via the parameter Activity after positioning 463.
Activity after positioning 463 Function

The drive is stopped with the stopping behavior of
0 - End of positioning
Operation Mode 630.
The drive is stopped until the next signal edge;
1 - Wait for positioning signal with a new edge of the position signal, it is accel-
erated in the previous direction of rotation.
The drive is held until the next signal edge; with a
2 - Reversal by new edge new edge of the position signal, it is accelerated in
the opposite direction of rotation.
The drive is stopped and the power output stage
3- Positioning; off
of the inverter is switched off.
The drive is stopped for the Waiting Time 464;
4- Start by time control after the waiting time, it is accelerated in the pre-
vious direction of rotation.
The drive is held for the Waiting Time 464; after
5- Reversal by time control the waiting time, it is accelerated in the opposite
direction of rotation.
The position reached can be maintained for the Waiting Time 464, then until the drive
is accelerated according to operation mode 4 or 5.
Parameter Settings
464 Waiting Time 0 ms 3600000 ms 0 ms

Positioning, Operation Mode 458 = 1
The diagram shows how the positioning to the set positioning distance is effected. The
positioning distance remains constant at different frequency values. At the reference
point, the position signal SPosi is generated. Starting from frequency fmax, the positioning
is effected at the set Deceleration (Clockwise) 421. At a lower frequency value f1, the
frequency remains constant for some time before the drive is stopped at the set decel-
eration.
If, during acceleration or deceleration of the machine, positioning is started by the
signal SPosi, the frequency at the time of the positioning signal is maintained.
f
fm ax
f1
Deceleration (Clockwise) 421
Um i n U
S pos i
Digital Input 6
Examples of reference positioning as a function of the parameter settings selected.
− The reference point is registered according to the parameter Signal Sources 459
in operation mode 16–S6IND, rising edge by a signal on digital input 6.
− The Positioning distance 460 with parameter value 0.000U (default) defines a
direct stop of the drive with the deceleration behavior selected in parameter Op-
eration Mode 630 and the selected Deceleration (Clockwise) 421. If a Position-
ing distance 460 is set, the positioning is effected at the set deceleration.
− The Signal correction 461 of the signal propagation time from the measurement
point to the frequency inverter is not used if it is set to 0 ms.
− The Load correction 462 can compensate a faulty positioning by the load behav-
ior. By default, this function is deactivated, i.e. set to 0.
− The Activity after positioning 463 is defined by operation mode 0–End of posi-
tioning.
− The Waiting Time 464 is not considered because operation mode 0 is selected for
the parameter Activity after positioning 463.
− The actual value Rotations 470 enables a direct comparison to the required Posi-
tioning distance 460. In the case of deviations, a Signal correction 461 or Load
correction 462 can be carried out.
106 106 Operating

11.6.2 Axle Positioning
For axle positioning a feedback system is mandatory. In most cases, an expansion
module for the feedback evaluation is needed as well.. An optional expansion module
and operating modes 1004 and 1104 for parameter Operation mode speed sensor 2
493 enable the evaluation of a speed sensor signal with reference impulse. The ad-
justment of this parameter is described in the manual of the optional expansion mod-
ule. The positioning is started if a start signal is received and the frequency drops
below an adjustable frequency limit. The machine stops with the selected stopping
behavior at the entered position angle.
To ensure the correct function of the axle positioning, the speed controller should be
optimized after the guided commissioning. This is described in the chapter "Speed
Controller".
Via the parameter Reference orientation 469, the angle between the reference point
and the required position is entered.
If this value is changed while the machine is at a standstill, the positioning operation
is carried out again at a frequency of 0.5 Hz. For this, a stopping behavior must be
selected for the parameter Operation Mode 630 which impresses a starting current
either permanently when the drive is at a standstill or for the stopping time (refer to
chapter „Stopping Behavior“).
Parameter Settings
469 Reference Orientation 0.0° 359.9° 0.0°
Caution! During the positioning operation, the direction of rotation of the drive
may change, regardless of whether the command Start clockwise or
Start anticlockwise was activated.
Make sure that the change of the direction of rotation cannot result in
any personal or material damage.
The positioning is started by a start command from a signal source (e.g. digital input)
which must be assigned to the parameter Start Positioning of Axle 37. The signal
source can be selected from the operation modes for digital inputs described in chap-
ter "Digital Inputs".
The positioning starts on condition that the Actual Frequency 241 of the output sig-
nal is lower than the value entered in parameter Positioning Frequency 471. Due to
a stopping behavior, the actual frequency drops below the positioning frequency.
Parameter Settings
471 Positioning Frequency 1.00 Hz 50.00 Hz 50.00 Hz
Via the parameter Max. positional error 472, the maximum permissible deviation
from the Reference orientation 469 can be set.
Parameter Settings
472 Max positional error 0.1° 90.0° 3.0°

Via parameter time constant positioning contr. 479, the time constant for controlling
the positional error can be set. The value of the time constant should be increased if
oscillations of the drive around the reference orientation occur during the positioning.
Parameter Settings
Time constant positioning
479 1.00 ms 9999.99 ms 20.00 ms
controller
To make sure that the set position is maintained if a load torque is applied, a stopping
behavior should be selected for parameter Operation Mode 630 which impresses a
starting current either permanently when the drive is at a standstill or for the stopping
time.
The status message „60-Arrived at desired Position“ which is displayed when the ref-
erence orientation is reached can be assigned to a digital output. The message is
output on the following conditions:
− Operation mode 2 (axle positioning) for parameter Operation Mode 458 is se-
lected.
− The controller release signal at digital input S1IND is switched on.
− Start Positioning of Axle 37 is activated.
− The speed sensor monitoring is activated, i.e. operation mode 2 (error message)
for parameter Operation Mode 760 of the speed sensor monitoring is selected.
− Operation mode 1004 or 1104 (quadruple evaluation with reference impulse) is
selected for the speed sensor input.
− The Actual Frequency 241 is lower than 1 Hz.
− The deviation of the current position from the reference orientation is lower than
the Max positional error 472.
The current position after Start Positioning of Axle 37 is recognized by the frequency
inverter as follows:
− During commissioning, after switching on the frequency inverter, a search mode is
performed for 3 rotations at a rotational frequency of 1 Hz in order to detect the
reference signal. As soon as the reference signal was recognized twice, the drive
is positioned to the Reference orientation 469.
− If the motor was already rotating before axle positioning was enabled, the posi-
tioning to the Reference orientation 469 is performed without search mode be-
cause the position of the reference point was already detected by the frequency
inverter.
If the positioning is carried out, after controller enabling and start command, when
the motor is at a standstill:
− The motor is positioned clockwise to the reference orientation if the value for the
reference orientation is higher than the value adjusted before.
− The motor is positioned anticlockwise to the reference orientation if the value for
the reference orientation is lower than the value adjusted before.
The sense of rotation during the positioning is independent of whether Start Clockwise
or Start Anticlockwise was activated.
The time required until the reference orientation is reached depends on:
− Actual Frequency
− Frequency ramp for deceleration
− Rotational angle to reference orientation
− Max positional error
− Time constant positioning controller

12 Error and warning behavior
Operation of the frequency inverter and the connected load are monitored continu-
ously. The monitoring functions are to be parameterized with the corresponding limit
values specific to the application. If the limits were set below the switch-off limit of
the frequency inverter, a fault switch-off can be prevented by suitable measures if a
warning message is issued.
The warning message is displayed by the LED's of the frequency inverter and can be
read out on the control unit via the parameter Warnings 269 or output via one of the
digital control outputs.
12.1 Overload Ixt

The admissible load behavior depends on various technical data of the frequency in-
verters and the ambient conditions.
The selected Switching Frequency 400 defines the nominal current and the available
overload for one second and sixty seconds, respectively. The Warning Limit Short-
Term Ixt 405 and Warning Limit Long-Term Ixt 406 are to be parameterized accord-
ingly.
Parameter Settings
405 Warning Limit Short Term Ixt 6% 100 % 80 %
406 Warning Limit Long Term Ixt 6% 100 % 80 %
12.2 Temperature
The ambient conditions and the power dissipation at the current operating point result
in the frequency inverter heating up. In order to avoid a fault switch-off of the fre-
quency inverter, the Warning Limit Heat Sink Temperature 407 for the heat sink
temperature limit and the Warning Limit Inside Temperature 408 as an internal tem-
perature limit are to be parameterized. The temperature value at which a warning
message is output is calculated from the type-dependent temperature limit minus the
adjusted warning limit.
The switch-off limits of the frequency inverter are an internal temperature of 65 °C
and a heat sink temperature range of 80°C up to 90°C.
Parameter Settings
407 Warning Limit Heat Sink Temp. -25 °C 0 °C -5 °C
408 Warning Limit Inside Temp. -25 °C 0 °C -5 °C

12.3 Controller Status
The intervention of a controller can be indicated via the control unit or LEDs. The
selected control method and the matching monitoring functions prevent a switch-off
of the frequency inverter. The intervention of the function changes the operating be-
havior of the application and can be displayed by the status messages with parameter
Controller Status 275. The limit values and events which result in the intervention by
the corresponding controller are described in the corresponding chapters.
The behavior during the intervention of a controller is configured with the parameter
Controller Status Message 409.

The intervention of a controller is not reported.
0 - No Message The controllers influencing the operating behavior are
displayed in the Controller status 275 parameter.
The limitation by a controller is displayed as a warning
1 – Warning Status
by the control unit.
Warning Status and The limitation by a controller is displayed as a warning
11 –
LED by the control unit and the LEDs.
Please refer to chapter 14.3.7 Warning Mask and chapter 20.3 Controller Status for a
list of controllers and further possibilities to evaluate the controller states.
12.4 IDC Compensation Limit

At the output of the frequency inverter a DC component can occur in the output cur-
rent due to unbalances. This DC voltage component can be compensated by the fre-
quency inverter. The maximum output voltage of the compensation is set with pa-
rameter IDC Compensation Limit 415. If a higher voltage than the set limit is needed
for the compensation of a DC voltage component, error “F1301 IDC COMPENSATION“
is triggered.
If this fault occurs, it should be checked whether the load is defective. Possibly the
voltage limit may have to be increased.
If the parameter IDC Compensation Limit 415 is reduced to zero, the DC compensa-
tion is deactivated.
Parameter Settings
1.5 1)
415 IDC Compensation Limit 0.0 V 1.5 V
0.0 2)
The factory setting of parameter Limit IDC compensation 415 depends on the setting of pa-
rameter Configuration 30:
1)
Configurations 1xx
2)
Configurations 2xx / 4xx
12.5 Frequency Switch-Off Limit

The maximum permissible output frequency of the frequency inverter can be set with
parameter Frequency Switch-Off Limit 417. If this frequency limit is exceeded by the
Stator frequency 210 or the Actual Frequency 241, the frequency inverter is
switched off and the fault message “F1100“ is displayed.
Parameter Settings
417 Frequency Switch-Off Limit 0.00 Hz 999.99 Hz 999.99 Hz
110 110 Operating

12.6 Motor Temperature
The configuration of the control terminals includes the monitoring of the motor tem-
perature. The monitoring function can be parameterized specific to the application via
the parameter Motor Temp. Operation Mode 570. The integration into the application
is improved by an operating mode with a delayed switch-off.

0 - Off Motor temperature monitoring switched off.
Therm.-Cont.: The critical point of operation is displayed by the control
1-
Warning only unit and parameter Warnings 269.
The fault switch-off is displayed by message F0400. The
2 - Error Switch-Off fault switch-off can be acknowledged via the control
unit or the digital input.
Therm.-Cont.: The fault switch-off according to operation mode 2 is
3 - Err.Switch-Off delayed by one minute.
1 min delayed
4 - Err.Switch-Off delayed by five minutes.
5 min delayed
5 - Err.Switch-Off delayed by ten minutes.
10 min delayed
Via parameter Therm. Contact 204, a digital input signal can be linked to the Motor
Temp. Operation Mode 570.
12.7 Phase Failure

A failure of one of the three motor or mains can lead to a damage in the frequency
inverter, the motor and the mechanical drive components. To prevent damage to
these components, the phases failure is monitored. Parameter Phase supervision 576
allows to adjust the behavior in case of a failure.
Phase Supervision 576 Function

In the case of a phase failure, the fault switch-off takes
Mains
10 - place after 5 minutes, fault F0703 is displayed. During
Error Switch-Off
this time, the warning message A0100 is displayed.
The phase supervision switches the frequency inverter
off:
Mains & Motor − immediately, in the case of a motor phase failure;
11 -
Error Switch-Off fault message F0403 is displayed,
− after 5 minutes in the case of a mains phase failure;
fault message F0703 is displayed.
Mains In the case of a mains phase failure, the drive is stopped
20 -
Shutdown after 5 minutes, fault F0703 is displayed.
The drive is stopped:
Mains & Motor
21 - − immediately, in the case of a motor phase failure,
Shutdown
− after 5 minutes in the case of a mains phase failure.

12.8 Automatic Error Acknowledgment
The automatic error acknowledgment enables acknowledgment of the faults Overcur-
rent F0500, Overcurrent F0507 and Overvoltage F0700 without intervention by an
overriding control system or the user. If one of the these errors occurs, the frequency
inverter switches off the power semi-conductors and waits for the time defined by the
parameter Restart Delay 579. If the error must be acknowledged, the speed of the
machine is determined via the quick catching function and it is synchronized to the
rotating machine. The automatic error acknowledgment makes use of quick catching
operation mode, regardless of the parameter for search run, Operation Mode 645.
The information given on this function in chapter "Search run" must be observed.
With parameter Allowed No. of Auto-Acknowl. 578, you can define the number of
automatic error acknowledgements which are permitted within 10 minutes.
An acknowledgement repeated above the permissible number within 10 minutes will

result in the frequency inverter being switched off. The errors Overcurrent F0500,
Overcurrent F0507 and Overvoltage F0700 have separate error acknowledgement
counters.
Parameter Settings
578 Allowed No. of Auto-Acknowl. 0 20 5
579 Restart Delay 0 ms 1000 ms 20 ms
112 112 Operating

13 Reference Values
The ACT series frequency inverters can be configured specific to the application and
enable customer-specific adaptation of the module hardware and software structure.
13.1 Frequency Limits

The output frequency of the frequency inverter and thus the speed setting range are
defined by the parameters Minimum Frequency 418 and Maximum Frequency 419.
The corresponding control methods use these two limit values for scaling and calculat-
ing the frequency.
Parameter Settings
3.50 Hz 1)
418 Minimum Frequency 0.00 Hz 999.99 Hz
0.00 Hz 2)
419 Maximum Frequency 0.00 Hz 999.99 Hz 50.00 Hz
The factory setting is dependend on the adjustment of parameter Configuration 30:
1)
3.5 Hz in configurations 1xx, 4xx
2)
0.00 Hz in configurations 2xx
13.2 Slip Frequency

The torque-forming current component and thus the slip frequency of the 3-phase
machine depend on the required torque in the case of the field-oriented control meth-
ods. The field-oriented control method also includes the parameter Slip Frequency
719 to limit the torque in the calculation of the machine model. The rated slip calcu-
lated from the rated motor parameters is limited in accordance with the Slip Fre-
quency 719 which is parameterized as a percentage.
Parameter Settings
719 Slip Frequency 0% 10000 % 250 %
13.3 Percentage Value Limits

The setting range of the percentages is defined by the parameters Minimum Refer-
ence Percentage 518 and Maximum Reference Percentage 519. The relevant control
methods use these two limit values for scaling and calculating the frequency.
Parameter Settings
518 Minimum Reference Percentage 0.00 % 300.00 % 0.00 %
519 Maximum Reference Percentage 0.00 % 300.00 % 100.00 %

13.4 Frequency Reference Channel
The various functions for the defining the reference frequency are connected via the
frequency reference value channel. The Reference Frequency Source 475 determines
the additive assignment of the available reference value sources depending on the
hardware installed.
Reference frequency source 475 Function
Reference value source is the multifunctional in-
1 - Abs. Analog Value MFI1A
put 1 in Operation Mode 452 - Analog signal.
The fixed frequency according to the Fixed Fre-
Abs. Val. Fixed Frequency
10 - quency Change-Over 1 66 and Fixed frequency
(FF)
change-over 2 67 as well as the current data set.
11 - Abs. Value MFI1A + FF Combination of the operation modes 10 and 1.
Reference value source is the function Frequency
20 - Abs. Value Motorpoti (MP) Motorpoti Up 62 and Frequency Motorpoti
Down 63.
21 - Abs. Value MFI1A + MP Combination of the operation modes 20 and 1.
Abs.Val. Speed Sensor 1 The frequency signals in Operation Mode 490
30 -
(F1) are evaluated as a reference value.
31 - Abs. Val. MFI1A + F1 Combination of the operation modes 30 and 1.
The frequency signal on the digital input accord-
Abs. Repetition Frequency
32 - ing to Operation mode 496 for the repetition
Input (F3)
frequency input.
33 - Abs. Val. MFI1A + F3 Combination of operation modes 1 and 32.
The KP 500 control unit is the reference value
40 - Abs. Value Motorpoti (KP) source, with keys ▲ for increasing the frequency
and ▼ for reducing the frequency.
41 - Abs. Value MFI1A + KP Combination of the operation modes 40 and 1.
Abs. Val.
Combination of the operation modes 1, 10, 40, 32
80 - MFI1A + FF + KP + F1 + F3
(+ analog input extension module)1).
+ (EM-S1INA)1)
Abs. Val. Combination of the operation modes 1, 10, 40,
81 - MFI1A + FF + KP + F1 + F3 30, 32
+ (EM-S1INA)1) (+ analog input extension module)1).
Abs. Val. Combination of the operation modes 1, 10, 40, 32
82 - MFI1A + FF + KP + F3 (+ absolute amount speed sensor 2 (F2))2)
+ (F2)2) + (EM-S1INA)1) (+ analog input extension module)1.
89 - MFI1A + FF + KP + F1 + F3 30, 32(+ absolute amount speed sensor 2 (F2))2)
+ (F2)2) + (EM-S1INA)1) (+ analog input extension module)1).
Abs. Val. MFI1A + FF + MP Combination of the operation modes 1, 10, 20, 32
90 -
+ F3 + (EM-S1INA)1) (+ analog input extension module)1).
Abs. Val. MFI1A + FF + MP Combination of the operation modes 1, 10, 20,
91 -
+ F1 + F3+ (EM-S1INA)1) 30, 32 (+ analog input extension module)1).
Abs. Val. MFI1A + FF + MP Combination of the operation modes 1, 10, 20, 32
92 - + F3 + (F2)2) (+ absolute amount speed sensor 2 (F2))2)
+ (EM-S1INA)1) (+ analog input extension module)1).
99 - MFI1A + FF + MP + F1 + 30, 32 (+ absolute amount speed sensor 2 (F2))2)
F3 + (F2)2) + (EM-S1INA)1) (+ analog input extension module)1).
101 to 199 Operation modes with signs (+/-).
1)
The reference value source is only available if an extension module with analog input is con-
nected. For information, refer to the extension module operating instructions.
2)
The reference value source is only available if an extension module with speed sensor input is
connected. For information, refer to the extension module operating instructions.
114 114 Operating

13.4.1 Block Diagram
The following table describes the software switches shown in the circuit diagram as a
function of the selected Reference Frequency Source 475.
Switch position on circuit diagram

Operation
MFI1A FF MP F1 F3 KP Sign
mode
1 1 Abs. value
10 1 Abs. value
11 1 1 Abs. value
20 1 Abs. value
21 1 1 Abs. value
30 1 Abs. value
31 1 1 Abs. value
32 1 Abs. value
33 1 1 Abs. value
40 1 Abs. value
41 1 1 Abs. value
80 1 1 1 1 Abs. value
81 1 1 1 1 1 Abs. value
82 1 1 1 1 Abs. value
89 1 1 1 1 1 Abs. value
90 1 1 1 1 Abs. value
91 1 1 1 1 1 Abs. value
92 1 1 1 1 Abs. value
99 1 1 1 1 1 Abs. value
101 1 +/-
110 1 +/-
111 1 1 +/-
120 1 +/-
121 1 1 +/-
130 1 +/-
131 1 1 +/-
132 1 +/-
133 1 1 +/-
140 1 +/-
141 1 1 +/-
180 1 1 1 1 +/-
181 1 1 1 1 1 +/-
182 1 1 1 1 +/-
189 1 1 1 1 1 +/-
190 1 1 1 1 +/-
191 1 1 1 1 1 +/-
192 1 1 1 1 +/-
199 1 1 1 1 1 +/-

116
Reference frequency source
116
Operation mode 475
Repetition frequency
0 F3
S2IND % 0
J re l.
S3IND
f
S6IND
1
Operation mode 496
Divider 497
Speed sensor 1
F1
S4IND 0
J re l.
f
S5IND 1
Blocking frequency
Operation mode 490
Absolute Start / Stop /
Division marks 491
S election of rotation
+ f2 Internal reference
Motorpoti Frequency limits
+ f1 frequency 22 8
0
Frequency motorpoti MP -+ f max
up 62 0 + Reference
Max. - f1 -1 f requency value
-+ f min
Min. 1 - f2 Min. Frequency 418 Start clockwise 68
Max. Frequency 419 Start anti-
Frequency motorpoti
clockwise 69
down 63
1st Blocking frequency 447
MFI1A
2nd Blocking frequency 448
Multifunction 0
Frequency hysteresis 449
analog
1
MFI1
digital

Operation mode 452
FF
Circuit diagram of frequency reference value channel
Fixed frequency
0
Fixed frequency 1 480
Fixed frequency 3 482 1
Change-over 1 66
Change-over 2 67
Motorpoti (KP)
Key Frequency-Motorpoti KP
up 0
Max.
Min. 1
Frequeny-Motorpoti
06/07
Key down
06/07
13.5 Reference Percentage Channel
The reference percentage channel combines various signal sources for definition of
the reference values. The percentage scaling facilitates integration into the applica-
tion, taking various process parameters into account.
The Reference Percentage Source 476 determines the additive assignment of the
available reference value sources depending on the hardware installed.
reference percentage source 476 Function

Reference value source is the multifunctional
1 - Abs. Analog Value MFI1A
input 1 in Operation Mode 452 - Analog signal.
The percentage according to Fixed Percent
10 - Abs. Fix. Perc. Val. (FP) Change-Over 1 75, Fixed Percent Change-Over
2 76 and the current data set.
11 - Abs. Value MFI1A + FP Combination of operation modes 1 and 10.
Reference value source is the function Percent
20 - Abs. Value Motorpoti (MP) Motorpoti Up 72 and Percent Motorpoti
Down 73.
21 - Abs. Value MFI1A + MP Combination of operation modes 1 and 20.
The frequency signal on the digital input accord-
Abs. Repetition Frequency
32 - ing to Operation Mode 496 of the repetition fre-
Input (F3)
quency input.
33 - Abs. Val. MFI1A + F3 Combination of operation modes 1 and 32.
Abs. Value MFI1A + FP + Combination of the operation modes 1, 10, 20, 32
90 -
MP + F3 (+ EM-S1INA) 1) (+ analog input of an extension module) 1).
1)
The reference value source is only available if an optional extension module with
analog input is connected. For information, refer to the extension module operating
instructions.
13.5.1 Block Diagram

The following table describes the software switches shown in the circuit diagram as a
function of the selected Reference Percentage Source 476.
Switch position on circuit diagram

Operation
MFI1A FP MP F3 Sign
mode
1 1 Abs. value
10 1 Abs. value
11 1 1 Abs. value
20 1 Abs. value
21 1 1 Abs. value
32 1 Abs. value
33 1 1 Abs. value
90 1 1 1 1 Abs. value
101 1 +/-
110 1 +/-
111 1 1 +/-
120 1 +/-
121 1 1 +/-
132 1 +/-
133 1 1 +/-
190 1 1 1 1 +/-

118
118
Reference percentage source
Operation mode 476
Repetition frequency
0
S2IND %
rel.
S3IND
f
S6IND
Divider 497
Motorpoti
Percentage-Motorpoti MP
up 72 0
Max. Absolute Start / Stop /
Selection of rotation
Min. 1 Reference
Percentage-Motorpoti Percentage limits percentage value 229
0
down 73 %max
Reference
+ -1 percentage value

Multifunction %min

analog
Start clockwise 68
Circuit diagram of percent reference value channel
Max. reference Start anti-

MFI1 clockwise 69
digital percentage 519
Operation mode 452
FP
Fixed percentage
0
Fixed percentage 1 520
Fixed percentage 3 522 1
Change-over 1 75
Change-over 2 76
06/07
06/07
13.6 Fixed Reference Values
The fixed reference values are to be parameterized as fixed frequencies or fixed per-
centages according to the configuration and function.
The signs of the fixed reference values determine the direction of rotation. A positive
sign means a clockwise rotation, a negative sign means an anticlockwise rotation. The
direction can only be changed via the sign if the Reference Frequency Source 475 or
Reference Percentage Source 476 is parameterized to an operation mode with sign
(+/-). The direction of rotation can also be stated with the digital signal sources as-
signed to the parameters Start Clockwise 68 and Start Anticlockwise 69.
The fixed reference values are to be parameterized in four data sets and are assigned
to further sources via the reference value channel. The use of the functions Data Set
Change-Over 1 70 and Data Set Change-Over 2 71 thus enables the setting of 16
fixed reference values.
13.6.1 Fixed Frequencies

The four fixed frequencies define reference values which are selected via the parame-
ters Fixed Frequency Change-Over 1 66 and Fixed Frequency Change-Over 2 67.
The parameter Reference Frequency Source 475 defines the addition of the various
sources in the reference frequency channel.
Parameter Settings
480 Fixed Frequency 1 -999.99 Hz 999.99 Hz 0.00 Hz
By combining the logic states of the fixed frequency change-over modes 1 and 2,
fixed frequencies 1 through 4 can be selected:
Fixed Frequency Control

Fixed Frequency Fixed Frequency
Function / active fixed value
Change-Over 1 66 Change-Over 2 67
0 0 Fixed Frequency 1 480
0 = contact open 1 = contact closed
13.6.2 JOG-Frequency
The JOG function forms part of the functions for controlling the drive mechanism via
the control unit. Use the arrow keys to change the JOG frequency within the function.
The frequency of the output signal is set to the entered value if the FUN key is
pressed. The drive starts and the machine turns at the set JOG-Frequency 489. If
the JOG frequency has been changed using the arrow keys, this value is stored.
Parameter Settings
489 JOG-Frequency -999.99 Hz 999.99 Hz 5.00 Hz

13.6.3 Fixed Percentages
The four percentage values define reference values which are selected via the parame-
ters Fixed Percent Change-Over 1 75 and Fixed Percent Change-Over 2 76. The
parameter Reference Percentage Source 476 defines the addition of the various
sources in the reference percentage channel.
Parameter Settings
520 Fixed Percentage 1 -300.00 % 300.00 % 0.00 %
By combining the logic states of the fixed percentage change-over modes 1 and 2,
Fixed Percentage Control

Fixed percentage value Fixed percentage value
Function / active fixed value
change-over 1 75 change-over 2 76
0 0 Fixed Percentage 1 520
13.7 Frequency ramps

The ramps determine how fast the frequency value is changed if the reference value
changes or after a start, stop or brake command. The maximum admissible ramp gra-
dient can be selected according to the application and the current consumption of the
motor.
If the settings of the frequency ramps are identical for both directions of rotation, the
parameterization via the parameters Acceleration (Clockwise) 420 and Deceleration
(Clockwise) 421 is sufficient. The values of the frequency ramps are taken over for
Acceleration Anticlockwise 422 and Deceleration Anticlockwise 423 if these have
been parameterized to the factory setting of -0.01 Hz/s.
The parameter value of 0.00 Hz/s for the acceleration blocks the corresponding direc-
tion of rotation.
Parameter Settings
420 Acceleration (Clockwise) 0.00 Hz/s 9999.99 Hz/s 5.00 Hz/s
421 Deceleration (Clockwise) 0.01 Hz/s 9999.99 Hz/s 5.00 Hz/s
422 Acceleration Anticlockwise -0.01 Hz/s 9999.99 Hz/s -0.01 Hz/s
423 Deceleration Anticlockwise -0.01 Hz/s 9999.99 Hz/s -0.01 Hz/s
120 120 Operating

The ramps for Emergency Stop Clockwise 424 and Emergency Stop Anticlockwise
425 of the drive to be activated via the parameter for stopping behavior Operation
Mode 630 must be selected according to the application. The non-linear (S-shaped)
course of the ramps is not active in the case of an emergency stop of the drive.
Parameter Settings
424 Emergency Stop Clockwise 0.01 Hz/s 9999.99 Hz/s 5.00 Hz/s
425 Emergency Stop Anticlockwise 0.01 Hz/s 9999.99 Hz/s 5.00 Hz/s
+f m ax
Rotary field
clockwise Acceleration Deceleration (Clockwise) 421
(Clockwise) 420 or
Emergency Stop C lockwise 424
t
Acceleration Deceleration anticlockwise 423
Rotary field (anticlockwise) 422 or
anticlockwise Emergency Stop anticlockwise 425
-f ma x
The parameter Maximum Leading 426 limits the difference between the output of the
ramp and the current actual value of the drive. The set maximum deviation is a dead
time for the control system which should be kept as low as possible.
In case the drive is loaded heavily and high acceleration and deceleration values are
selected it is possible, that a set controller limit is reached while the drive is acceler-
ated or decelerated. In this case, the drive cannot follow the defined acceleration or
deceleration ramps. With Maximum Leading 426, you can limit the max. leading of
the ramp.
Parameter Settings
426 Maximum Leading 0.01 Hz 999.99 Hz 5.00 Hz
Example: Fixed value at ramp output = 20 Hz, current actual value of drive = 15 Hz,
selected Maximum Leading 426 = 5 Hz
The frequency at the ramp output is increased to 15 Hz only and it is not increased
further. The difference (leading) between the frequency value at the ramp output and
the current actual frequency of the drive is limited to 5 Hz in this way.
The load occurring in a linear acceleration of the drive is reduced by the adjustable
modification speeds (S curve). The non-linear course of the frequency is defined as a
ramp and states the time range in which the frequency is to be guided to the set ramp.
The values set with parameters 420 to 423 are maintained regardless of the selected
ramp times.

Setting the ramp time to 0 ms deactivates the function S curve and enables the use of
the linear ramps. The data set change-over of the parameters within an acceleration
phase of the drive demands the defined take-over of the values. The controller calcu-
lates the values required in order to reach the reference value from the ratio of the
acceleration to the ramp time and uses it until the acceleration phase is finished. With
this method, exceeding the reference values is avoided and a data set change-over
between extremely deviating values becomes possible.
Parameter Settings
430 Ramp Rise Time Clockwise 0 ms 65000 ms 0 ms
431 Ramp Fall Time Clockwise 0 ms 65000 ms 0 ms
432 Ramp Rise Time Anticlockwise 0 ms 65000 ms 0 ms
433 Ramp Rise Time Anticlockwise 0 ms 65000 ms 0 ms
Ramp Fall Time Clockwise 431
Ramp Rise Time Clockwise 43 0
+f m ax
Rotary field
clockwise Frequency reference value = 0.00 Hz
t
t au fr
Rotary field t au f
anticlockwise
-f ma x
Ramp Rise Time Anticlockwise 432

Ramp Rise Time Anticlockwise 433
Example: Calculation of the acceleration time in clockwise rotation at an accelera-

tion from 20 Hz to 50 Hz (fmax) and an acceleration ramp of 2 Hz/s for
parameter Acceleration (Clockwise) 420. The parameter Ramp Rise
Time Clockwise 430 is set to 100 ms.
Δf taufr = acceleration time

t aufr = clockwise rotary field
ar
∆f = change of frequency
50 Hz − 20 Hz acceleration ramp
t aufr = = 15 s
2 Hz/s
ar = Acceleration
Clockwise
t auf = t aufr + t Vr
t auf = 15 s + 100 ms = 15.1 s tVr = Ramp Rise Time Clockwise
acceleration time +
tauf = ramp rise time
122 122 Operating

13.8 Percentage Value Ramps
The percentage value ramps scale the change of the reference value (in percent) for
the corresponding input function. The acceleration and deceleration of the drive are
parameterized via the frequency ramps.
The behavior Gradient Percentage Ramp 477 corresponds to a function which takes
the time response of the drive system into account. If the parameter is set to 0 %/s,
this function is deactivated and a direct reference value modification for the following
function is obtained.
The default value depends on the parameter Configuration 30.
Parameter Settings
477 Gradient Percentage Ramp 0 %/s 60.000 %/s x %/s
13.9 Block Frequencies

In certain applications, it is necessary to fade out reference frequencies. In this way,
resonance points of the system as stationary operating points are avoided. The pa-
rameters 1st Blocking Frequency 447 and 2nd Blocking Frequency 448 with the
parameter Frequency Hysteresis 449 define two resonance points.
A block frequency is active if the parameter values of the block frequency and the
frequency hysteresis are not equal to 0.00 Hz.
The area faded out as a stationary working point by the hysteresis is passed through
as quickly as possible according to the selected ramp for V. If the output frequency is
limited as a result of the selected control parameter settings, e.g. if the current limit is
reached, the hysteresis is passed through with a delay. The behavior of the reference
value can be determined from its direction of movement according to the following
diagram.
Parameter Settings
447 1st Blocking Frequency 0.00 Hz 999.99 Hz 0.00 Hz
448 2nd Blocking Frequency 0.00 Hz 999.99 Hz 0.00 Hz
449 Frequency Hysteresis 0.00 Hz 100.00 Hz 0.00 Hz
reference value output
hysteresis hysteresis
fblock internal
fblock-hysteresis fblock+hysteresis reference value

13.10 Motor Potentiometer
The motor potentiometer is used for controlling the motor speed using
• digital control signals (Function Motorpoti MP) or

• the keys of the KP 500 control unit (Function Motorpoti KP)
The following functions are assigned to the Up/Down control commands:
Activation
Motorpoti (MP) Motorpoti (KP) Function
Up Down Up Down
Output signal does not change.
0 0 – –
Output value rises
1 0 ▲ –
at set ramp.
Output value drops
0 1 – ▼
at set ramp.
Output value is reset
1 1 ▲+▼
to initial value.

▲ ▼ = arrow keys at KP 500 control unit
The motor potentiometer function as well as its assignment to other reference value
sources can be selected in the corresponding reference value channels via parameters
Reference Frequency Source 475 or Reference Percentage Source 476.
Refer to Chapters "Frequency Reference Channel" and "Reference percentage chan-
nel" for the possible reference value source assignments.
The availability of the functions "Motorpoti (MP)" and "Motorpoti (KP)" varies in the
different reference value channels:
Reference value channel

Reference Frequency Reference Percent-
Source 475 age Source 476
Motorpoti (MP) X X
Motorpoti (KP) X 0
X = Function available 0 = Function not available
Depending on the active reference value channel, the function is assigned to a digital
signal via parameters Frequency Motorpoti Up 62, Frequency Motorpot. Down 63 or
Percent Motorpo. Up 72, Percent Motorpoti Down 73.
Refer to Chapter "Digital Inputs" for a list of the available digital signals.
124 124 Operating

The Operation Mode 474 of the motor potentiometer function defines the behavior of
the function at various operating points of the frequency inverter.
Operation Mode 474 Function

In the operation mode motor potentiometer non-
0 - Not Latching storing (not latching), the drive goes to the set
minimum reference value at each start.
In the operation mode storing (latching) the motor
goes to the reference value selected before the
1 - latching switch-off at the start. The reference value is also
stored when the device is switched off.
The operation mode Motorpoti taking over is to be

used for the data set change-over of the reference
2 - Taking Over
value channel. The current reference value is used
by changing to the motorpoti function.
This operation mode combines the behavior in op-
3 - Taking Over and Latching
eration mode 1 and 2.
13.10.1 Motorpoti (MP)

The Function "Motorpoti (MP)" can be parameterized via the parameters Reference
Frequency Source 475 or Reference Percentage Source 476.
Frequency Reference Channel

Via the digital control inputs, the required functions Frequency Motorpoti Up 62 and
Frequency Motorpot. Down 63 are activated.
The reference values are limited via parameters Minimum Frequency 418 and Maxi-
mum Frequency 419.
Reference percentage channel

Via the digital control inputs, the required functions Percentage Motorpoti Up 72 and
Percentage Motorpot. Down 73 are activated. The reference values are limited via
parameters Minimum Percentage 518 and Maximum Percentage 519.
13.10.2 Motorpoti (KP)

The function "Motorpoti (KP)" is only available in the reference frequency channel.
The function and its assignment to other reference value sources can be selected via
parameter Reference Frequency Source 475.
Via the keys of the KP 500 control unit, the required functions Frequency Motorpoti
Up 62 and Frequency Motorpot. Down 63 are activated.
The reference values are limited via parameters Minimum Frequency 418 and Maxi-
mum Frequency 419.
The function is used as described in Chapter "Controlling the

Motor via the Control Unit".
When the function Motorpoti (KP) is active "inPF" will be dis-
played for clockwise operation and "inPr" will be displayed for
anti-clockwise operation.

The control unit keys have the following functions:
Key functions
▲/▼ Increase / reduce frequency.
ENT Reversal of the direction of rotation independent of the control signal on

the terminals Clockwise S2IND or Anticlockwise S3IND.
ENT Save the selected function as default value. The direction of rotation is not
(1 sec) exchanged.
ESC Cancel function and return to the menu structure.
FUN Switch from internal set point inP to JOG frequency; the drive starts.
Release the key to switch to the sub-function and stop the drive.
RUN Start drive; alternative to control signal S2IND or S3IND.
STOP Stop drive; alternative to control signal S2IND or S3IND.
13.10.3 Controlling the Motor via the Control Unit

The parameter Reference Frequency Source 475 enables the assignment of the refer-
ence value sources in the frequency reference value channel. Operation modes can be
set without the function "Motorpoti (KP)".
If an operation mode is selected without "Motorpoti (KP)", it is still possible to control
a connected motor via the keys of the KP 500 control unit.
The function is activated as described in "Control Unit KP500, Controlling the Motor via
the Control Unit".
The speed of the modification of the reference value is limited by the parameter Ramp
Keypad-Motorpoti 473.
Parameter Settings
473 Ramp Keypad-Motorpoti 0.00 Hz/s 999.99 Hz/s 2.00 Hz/s
126 126 Operating

13.11 Repetition frequency input
The use of a frequency signal completes the various possibilities of the reference
value specification. The signal at one of the available digital inputs is evaluated ac-
cording to the selected Operation Mode 496.

0 - Off Repetition frequency is zero.
S2IND One edge of the frequency signal at terminal
21 -
Single Evaluation pos. X210A.4 is evaluated with a positive sign.
S2IND Both edges of the frequency signal at terminal
22 -
Double Evaluation pos. X210A.4 are evaluated with a positive sign.
31 -
Single Evaluation pos. X210A.5 is evaluated with a positive sign.
32 -
Double Evaluation pos. X210A.5 are evaluated with a positive sign.
61 -
Single Evaluation pos. X210B.1 is evaluated with a positive sign.
62 -
Double Evaluation pos. X210B.1 are evaluated with a positive sign.
Operation modes 21 to 62 with evaluation of the
121 to 162
frequency signal, but with a negative sign.
Note: If a digital input is configured as a repetition frequency input, this input

cannot be used for other functions.
Check the link of the digital inputs to other functions.
The signal frequency at the selected repetition frequency input can be scaled via the
parameter Divider 497. The parameter figure is comparable with the division marks
of a speed sensor per rotation of the drive. The frequency limit of the parameterized
digital input is to be taken into account for the frequency of the input signal.
Parameter Settings
497 Divider 1 8192 1024
Note: The reference value specification within the different functions enables
the use of the repetition frequency signal as a percentage figure. A sig-
nal frequency of 100 Hz at the repetition frequency input corresponds to
100%, 1 Hz corresponds to 1%. The parameter Divider 497 is to be
used in a way comparable with the speed sensor simulation.

14 Control Inputs and Outputs
The modular structure of the frequency inverters enables a wide spectrum of applica-
tions on the basis of the available hardware and software functionality. The control
inputs and outputs of terminals X210A and X210B described in the following can be
linked to software modules freely via the described parameters.
14.1 Multi-function input MFI1

Multifunction input MFI1 can either be configured as a voltage, current or a digital
input. Depending on the selected Operation Mode 452 for the multifunction input, a
link to various functions of the software is possible. The unused operation modes are
assigned the signal value 0 (LOW).

1 - Voltage Input voltage signal (MFI1A), 0 V ... 10 V
2 - Current Input current signal (MFI1A), 0 mA ... 20 mA
3 - Digital Input digital signal (MFI1D), 0 V ... 24 V
Note: The sampling rate of multi-function input MFI1D is slower than that of
digital signals S1IND, S2IND, etc. For this reason, this input should only
be used for signals which are not time-critical.
14.1.1 Analog Input MFI1A

Multifunction input MFI1 is configured by default for an analog reference value source
with a voltage signal of 0 V to 10 V.
Alternatively, you can select the operation mode for an analog current signal of 0 mA
to 20 mA. The current signal is continuously monitored and the fault message "F1407"
displayed if the maximum figure is exceeded.
14.1.1.1 Characteristic
Mapping of the analog input signal onto a reference frequency value or a reference
percentage value is possible for various requirements. Parameterization can be done
via two points of the linear characteristic of the reference value channel.
Point 1 with coordinates X1 and Y1 and point 2 with coordinates X2 and Y2 can be set
in four data sets.
Parameter Settings
454 Point X1 0.00 % 100.00 % 2.00 %
455 Point Y1 -100.00 % 100.00 % 0.00 %
456 Point X2 0.00 % 100.00 % 98.00 %
457 Point Y2 -100.00 % 100.00 % 100.00 %
The coordinates of the points relate, as a percentage, to the analog signal with 10 V
or 20 mA and parameter Maximum Frequency 419 or parameter Maximum Reference
Percentage 519. The direction of rotation can be changed via the digital inputs
and/or by selection of the points.
Attention! The monitoring of the analog input signal via the parameter Er-
ror/Warning Behavior 453 demands the examination of the parameter
Point X1 454.

The following characteristic is set by default and can be adapted to the application via
the parameters mentioned.
Y
( X2 / Y2 )
pos. maximum value Point 1:
X1 = 2.00% ⋅ 10 V = 0.20 V
Y1 = 0.00% ⋅ 50.00 Hz = 0.00 Hz
Point 2:
X2 = 98.00% ⋅ 10 V = 9.80 V
Y2 = 100.00% ⋅ 50.00 Hz = 50.00 Hz
0V +10V X
(0mA) ( X1 / Y1 ) (+20mA)
neg. maximum value
The freely configurable characteristic enables setting a tolerance at the ends as well
as a reversal of the direction of rotation.
The following example shows the inverse reference value specification with additional
reversal of the direction of rotation. This is often used in pressure control systems.
Y
pos. maximum value Point 1:
100%
( X1 / Y1 ) X1 = 2.00% ⋅ 10 V = 0.20 V
Y1 = 100.00% ⋅ 50.00 Hz = 50.00 Hz
Point 2:
+10V
(+20mA) X2 = 98.00% ⋅ 10 V = 9.80 V
Y2 = −80.00% ⋅ 50.00 Hz = −40.00 Hz
0V X
(0mA)
The reversal of the direction of rotation is
effected in this example at an analog
input signal of 5.5V.
-80%
( X2 / Y2 )
The definition of the analog input characteristic can be calculated via the two-point
form of the line equation. The speed Y of the drive is controlled according to the ana-
log control signal X.
Y2 - Y1
Y= ⋅ (X − X1) + Y1
X2 - X1

14.1.1.2 Scaling
The analog input signal is mapped to the freely configurable characteristic. The maxi-
mum admissible setting range of the drive can be set via the frequency limits or per-
centage limits according to the configuration selected. In the case of the parameteri-
zation of a bipolar characteristic, the set minimum and maximum limits for both direc-
tions of rotation are effective. The percentage values of the characteristic points are
relative to the limits selected.
Parameter Settings
3.50 Hz 1)
418 Minimum Frequency 0.00 Hz 999.99 Hz
0.00 Hz 2)
419 Maximum Frequency 0.00 Hz 999.99 Hz 50.00 Hz
The factory settings depend on the setup of parameter Configuration 30:

1)
2)
The control system uses the maximum value of the output frequency, which is calcu-
lated from the Maximum Frequency 419 and the compensated slip of the drive. The
frequency limits define the speed range of the drive, and the percentage values sup-
plement the scaling of the analog input characteristic in accordance with the functions
configured.
Parameter Settings
518 Minimum Reference Percentage 0.00 % 300.00 % 0.00 %
519 Maximum Reference Percentage 0.00 % 300.00 % 100.00 %
14.1.1.3 Tolerance Band and Hysteresis

The analog input characteristic with change of sign of the reference value can be
adapted by the parameter Tolerance Band 450 of the application. The adjustable
tolerance band extends the zero passage of the speed relative to the analog control
signal. The parameter value (percent) is relative to the maximum current or voltage
signal.
Parameter Settings
450 Tolerance Band 0.00 % 25.00 % 2.00 %
(X2 / Y2) (X2 / Y2)

pos. maximum value pos. maximum value
0V +10V 0V +10V
(0mA) (+20mA) (0mA) (+20mA)
zero point
tolerance band
(X1 / Y1) (X1 / Y1)
neg. maximum value neg. maximum value
Without tolerance band With tolerance band
130 130 Operating

The default Minimum Frequency 418 or Minimum Percentage 518 extends the pa-
rameterized tolerance band to the hysteresis.
(X2 / Y2)
pos. maximum value
pos. minimum value
+10V
neg. minimum value (+20mA)
zero point
tolerance band
(X1 / Y1)
neg. maximum value
Tolerance band with set maximum frequency
For example, the output variable coming from positive input signals is kept on the
positive minimum value until the input signal becomes lower than the value for the
tolerance band in the negative direction. Then, the output variable follows the set
characteristic.
14.1.1.4 Filter Time Constant

The time constant of the filter for the analog reference value can be set via the pa-
rameter Filter Time Constant 451.
The time constant indicates the time during which the input signal is averaged by
means of a low pass filter, e.g. in order to eliminate fault effects.
The setting range is between 0 ms and 5000 ms in 15 steps.
Filter Time Constant 451 Function

Filter deactivated – analog reference value is for-
0 - Time Constant 0 ms
warded unfiltered.
2 - Time Constant 2 ms Filter activated – averaging of the input signal via
4 - Time Constant 4 ms the set value of the filter time constants.

14.1.1.5 Error and warning behavior
For monitoring the analog input signal, an operation mode can be selected via pa-
rameter Error/Warning Behavior 453.
Error/Warning Behavior 453 Function

0 - Off The input signal is not monitored.
If the input signal is lower than 1 V or 2 mA, a
1 - Warning < 1V/2mA
warning message is issued.
2 - Shut Down < 1V/2mA warning message is issued; the drive is deceler-
ated according to stopping behavior 2.
Error Switch-Off
3- warning and fault message is issued and the drive
< 1V/2mA
coasts to a standstill (stopping behavior 0).
Monitoring of the analog input signal is active regardless of the release of the fre-
quency inverter according to the operation mode selected.
Operation mode 2 defines the shut-down and stopping of the drive, regardless of the
setting of parameter Operation Mode 630 for the stopping behavior. The drive is
stopped according to stopping behavior 2. If the set holding time has expired, an er-
ror message is issued. The drive can be started again by switching the start signal on
and off.
Operation mode 3 defines the free coasting of the drive (like described for stopping
behavior 0), regardless of the setting of parameter Operation Mode 630 for the stop-
ping behavior.
Attention! The monitoring of the analog input signal via the parameter Er-
ror/Warning Behavior 453 demands the examination of the parameter
Point X1 454.
Example: Error/Warning Behavior 453 = “2 - Shut Down < 1V/2mA” or “3 - Error
Switch-Off < 1V/2mA. In the factory setting of parameter Point X1 454 shut down or
error switch-off is activated at an output frequency unequal to 0 Hz. If shut down or
error switch-off should be activated at an output frequency equal to 0 Hz the parame-
ter Point X1 454 must be adjusted (e.g. X1=10% /1 V).
Y
50 Hz
(X1=2% / Y1=0%)
0 Hz
0,2 V 1V 9,8 V X
14.2 Multi-function output MFO1

Multifunction output MFO1 can either be configured as a digital, analog or a repetition
frequency output. Depending on the selected Operation mode 550 for the multifunc-
tion output, a link to various functions of the software is possible. The operation
modes not used are deactivated internally.

0 - Off Output has the logic signal LOW.
1 - Digital Digital output, 0 ... 24 V.
2 - Analog Analog output, 0 ... 24 V.
Repetition frequency output, 0 ... 24 V, fmax = 150
3 - Repetition frequency
kHz.
132 132 Operating
14.2.1 Analog Output MFO1A
By default, the multifunction output MFO1 is configured for the output of a pulse
width modulated output signal with a maximum voltage of DC 24 V.
The selected configuration determines which actual values can be selected for pa-
rameter Analog Operation 553 of multifunction output 1.
Analog operation 553 Function

0 - Off Analog operation MFO1 is switched off.
Absolute value of stator frequency 1,
1 - Abs. Fs
0.00 Hz ... Maximum Frequency 419.
Absolute value of stator frequency,
Abs. Fs betw.
2- Minimum Frequency 418 ... Maximum Fre-
fmin/fmax
quency 419.
Absolute value of speed sensor signal 1,
3 - Abs. Speed Sensor 1
Absolute value of actual frequency,
7 - Abs. Actual Frequency
Absolute value of current active current IACTIVE,
20 - Abs. Iactive
0.0 A ... FU rated current.
Abs. value of flux-forming current component,
21 - Abs. Isd
Abs. value of torque-forming current component,
22 - Abs. Isq
Absolute value of current active power PACTIVE,
30 - Abs. Pactive
0.0 kW ... Rated Power 376.
Absolute value of calculated torque M,
31 - Abs. M
0.0 Nm ... rated torque.
Abs. Inside Tempera- Abs. value of measured inside temperature,
32 -
ture 0 °C ... 100 °C.
Abs. Heat Sink Tem- Abs. value of measured heat sink temperature,
33 -
perature 0 °C ... 100 °C.
Abs. Analog Input Absolute signal value at analog input 1,
40 -
MFI1A 0.0 V ... 10.0 V.
Absolute current value of the measured output cur-
50 - Abs. I rents,
DC link voltage Ud,
51 - DC link voltage
0.0 V ... 1000.0 V.
Output voltage V,
52 - V
0.0 V ... 1000.0 V.
Absolute value of calculated volumetric flow
53 - Volume Flow
0.0 m3/h ... Nominal Volumetric Flow 397.
Absolute value of calculated pressure
54 - Pressure
0.0 kPa ... Nominal Pressure 398.
101 to 133 Operation modes in analog operation with signs.
14.2.1.1 Output Characteristic

The voltage range of the output signal at multifunction output 1 can be adjusted. The
value range of the actual value selected via parameter Analog Operation 553 is as-
signed to the value range of the output signal which is adjusted via the parameters
Voltage 100% 551 and Voltage 0% 552.

Parameter Settings
551 Voltage 100% 0.0 V 22.0 V 10.0 V
552 Voltage 0% 0.0 V 22.0 V 0.0 V
Actual abs. value Analog Operation 553: Analog Operation 553 with signs:
+24V +24V
+10V +10V
+5V
0V 0V
0% -100% 0% 100%
50% 100%
With the parameters Voltage 100% 551 and Voltage 0% 552, the voltage range at
100% and 0% of the output parameter is set. If the output value exceeds the refer-
ence value, the output voltage also exceeds the value of the parameter Voltage 100%
551 up to the maximum value of 24V.
14.2.2 Frequency Output MFO1F

The multifunctional output MFO1 can be used as a frequency output if the corre-
sponding Operation Mode 550 is selected. The 24V output signal is assigned to the
abs. value of the speed or frequency via the parameter Repetition Freq. Operation
555. The selection of the operation modes depends on the expansion modules in-
stalled as an option.
Repetition Freq. Operation Function

555
0 - Off Repetition frequency operation MFO1 switched off.
1 - Actual Frequency Abs. value of the Actual Frequency 241.
2 - Stator Frequency Abs. value of the Stator Frequency 210.
3 - Frequency Speed Sensor 1 Abs. value of the Encoder 1 Frequency 217.
5 - Repetition Frequency Input Abs. value of the Repetition Frequency Input 252.
14.2.2.1 Scaling
The repetition frequency mode for the multifunction output corresponds to the emula-
tion of an incremental sensor. The parameter Division Marks 556 must be param-
eterized according to the frequency to be output.
Parameter Settings
556 Division marks 30 8192 1024
The frequency limit of fmax=150 kHz must not be exceeded in the calculation of the
parameter Division marks 556, i.e. the requirement
150000 Hz
Smax ∗ abs. frequency value ∗ 150 kHz must be met. S max =
Frequency value

14.3 Digital Outputs
The OP. Mode Digital Output 1 530 and the relay output with the parameter Op.
Mode Digital Output 3 532 link the digital outputs to various functions. The selection
of the functions depends on the parameterized configuration. The use of the multi-
functional output MFO1 as a digital output demands selection of an Operation Mode
550 and linking via parameter Digital Operation 554.
Operation mode 530,532,554 Function

0 - Off Digital output is switched off.
Frequency inverter is initialized and on stand-by
1 - Ready or Standby Signal
or in operation.
Controller release signal and a start command are
2 - Run Signal
present, output frequency available.
Message is displayed via the parameter Current
3 - Error Signal
Error 259 or Warnings 269.
The Stator Frequency 210 is higher than the
4 - Setting Frequency
parameterized Setting Frequency 510.
Reference Frequency The Actual Frequency 241 of the drive has
5-
reached reached the Internal Reference Frequency 228.
Reference Percentage The Actual Percentage Value 230 has reached
6-
Reached the Reference Percentage Value 229.
The Warning Limit Short-Term Ixt 405 or Warn-
7 - Ixt warning
ing Limit Long-Term Ixt 406 has been reached.
Warning Max. heat sink temperature TK of 80 °C minus the
8-
Heat sink temperature Warning Limit Heat Sink Temp. 407 reached.
Warning Max. inside temperature Ti of 65 °C minus the
9-
Inside temperature Warning Limit Inside Temperature 408 reached.
Warning behavior according to parameterized
10 - Warning Motor Temperature Motor Temp. Operation Mode 570 at max. motor
temperature TPTC.
The message is displayed via parameter Warn-
11 - Warning General
ings 269.
The selected limit values Warning Limit Heat Sink
Temp. 407, Warning Limit Inside Temp 408 or
12 - Warning over temperature
the maximum motor temperature have been ex-
ceeded.
Failure of the mains voltage and power regulation
13 - Mains Failure active according to Operation Mode 670 for the
voltage controller.
Warning Motor Protect. Parameterized Operation Mode 571 for the motor
14 -
Switch protection switch has triggered.
A controller or the Operation Mode 573 of the
15 - Warning Current Limitation
intelligent current limits limit the output current.
Controller Current Limit. The overload reserve for 60 s has been used up
16 -
Long Term Ixt and the output current is being limited.
Controller Current Limit. The overload reserve for 1 s has been used up
17 -
Short Term Ixt and the output current is being limited.
Max. heat sink temperature TK reached, intelli-
18 - Controller Current Limit. TK
gent current limits of Operation Mode 573 active.
Controller Current Limit. Max. motor temperature reached, intelligent cur-
19 -
Motor Temp. rent limits of Operation Mode 573 active.
The comparison according to the selected OP.
20 - Comparator 1
mode Comparator 1 540 is true.
Table "Operation Modes for Digital Outputs" continued on next page.

Operation mode Function
21 - Comparator 2
Warning of Operation Mode 581 of V-belt moni-
22 - Warning V-belt
toring.
The selected Operation Mode Timer 1 790 gen-
23 - Timer 1
erates an output signal of the function.
The selected Operation Mode Timer 2 793 gen-
24 - Timer 2
erates an output signal of the function.
Message of the configurable parameter Create
25 - Warning Mask
Warning Mask 536.
30 - Flux Formation Ended Magnetic field has been impressed.
Activation of a brake unit depending on the Op-
eration Mode 620 for the starting behavior, Op-
41 - Open brake
eration Mode 630 for the stopping behavior or
the configured brake control system.
The Switch-On Temperature 39 has been
43 - External Fan
reached.
Reference orientation 469 of axle positioning
60 - Arrived at desired Position
reached.
Signal from output of logic module 1, according to
70 - Logic Function 1
parameterized Operation Mode Logic 1 198.
100 to 173 Operation modes inverted (LOW active).
14.3.1 Setting Frequency

If operation mode 4 is selected for a digital output, the corresponding output be-
comes active if the Stator Frequency 210 has exceeded the value set under the pa-
rameter Setting Frequency 510.
The relevant output is switched over again as soon as the Stator Frequency 210 falls
below the value selected for the setting frequency.
Parameter Settings
510 Setting Frequency 0.00 Hz 999.99 Hz 3.00 Hz
14.3.2 Reference value reached

In operation mode 5 or 6 for a digital output, a message is generated via the corre-
sponding output when the actual frequency or actual percentage value has reached
the reference value.
The maximum deviation can be defined as a percentage of the adjustable range (Max
- Min) via the parameter Max. Control Deviation 549.
Parameter Settings
549 Max. Control Deviation 0.01 % 20.00 % 5.00 %

14.3.3 Flux Formation Ended
If operation mode 30 is selected for a digital output the corresponding output be-
comes active when the flux formation is ended. The time for the flux formation results
from the operating state of the machine and the set parameters for magnetizing the
machine. The magnetizing can be defined via the starting behavior and is influenced
by the amount of the set starting current.
14.3.4 Open brake

The Open brake function in operation mode 41 enables the activation of a corre-
sponding unit via the digital control output. The function uses both the control com-
mands via the contact inputs and the set starting and stopping behavior for controlling
the digital output.
According to the configured starting behavior, the output is switched on when the
magnetizing of the motor is finished. The brake is released and the drive is acceler-
ated.
The stopping behavior of the drive depends on the configuration of the parameters
Operation Mode 630. This is described in chapter "Stopping Behavior".
If stopping behavior 2 or 5 with stop function is selected, the drive is controlled to
zero speed and the digital output is not switched off. In the other operation modes of
the stop behavior, the control of the brake is possible. At the start of a free coasting
of the drive, the digital output is switched off.
This is similar to the behavior in the case of the stopping behavior with shutdown. The
drive is decelerated and supplied with current for the set holding time. Within the set
holding time, the control output is switched off and thus the brake activated.
Control of Brake
Operation mode "41-Open brake" switches off the digital
Stopping Behavior
output assigned to the function immediately. The me-
0
chanical brake is activated.
Operation mode "41-Open brake" switches off the digital
Stopping Behavior
output assigned to the function when Switch-Off Thresh-
1, 3, 4, 6, 7
old 637 is reached. The mechanical brake is activated.
Operation mode "41-Open brake" leaves the digital output
Stopping Behavior
assigned to the function switched on. The mechanical
2, 5
brake remains open.
14.3.5 Current Limitation

Operation modes 15 to 19 link the digital outputs and the relay output to the func-
tions of the intelligent current limits. The reduction of power by the set figure in per-
cent of the rated current depends on the selected operation mode. Accordingly, the
event for intervention of the current limitation can be output via the operation modes
of the digital outputs. If the function of the intelligent current limits is deactivated
within the sensor-less control, operation modes 16 to 19 are switched off in the same
way.
14.3.6 External Fan

Operation mode 43 enables the control of an external fan. Via the digital output, the
fan is switched on if the controller is released and Start clockwise or Start anticlock-
wise are switched on, or if the Switch-On Temperature 39 for the internal fan was
reached.

14.3.7 Warning Mask
The logic signals of various monitoring and control functions can be set via the opera-
tion mode for parameter Create Warning Mask 536. According to the application, any
number of warnings and controller status messages can be combined. This enables
internal or external control via a common output signal.
Create Warning Mask 536 Function

0 - No Change Configured warning mask is not modified.
The warnings and controller status messages stated
1- Activate everything
are linked in the warning mask.
The warnings reports stated are linked in the warn-
2- Activate all Warnings
ing mask.
Activate all Controller The controller status reports stated are linked in the
3-
States warning mask.
10 - Warning Ixt The frequency inverter is overloaded.
Overload reserve for 1 s minus the Warning Limit
11 - Warning Short-Term Ixt
Short-Term Ixt 405 has been reached.
Overload reserve for 60 s minus the Warning Limit
12 - Warning Long-Term Ixt
Long-Term Ixt 406 has been reached.
Max. heat sink temperature TK of 80 °C minus the
Warning Heat Sink Tem-
13 - Warning Limit Heat Sink Temperature 407 has
perature
been reached.
Warning Max. inside temperature Ti of 65 °C minus the
14 -
Inside Temperature Warning Limit Inside Temperature 408 reached.
The controller stated in Controller Status 355 limits
15 - Warning Limit
the reference value.
16 - Warning Init Frequency inverter is initialized.
Warning behavior according to parameterized Mo-
Warning Motor Tempera-
17 - tor Temp. Operation Mode 570 at max. motor
ture
temperature TPTC.
Warning
18 - Phase Supervision 576 reports a phase failure.
Phase Failure
Warning Operation Mode 571 for the motor protective
19 -
Motor Protection Switch switch has triggered.
The Maximum Frequency 419 has been exceeded.
20 - Warning Fmax
The frequency limitation is active.
Warning The input signal is lower than 1V/2mA according to
21 -
Analog Input MFI1A the operation mode Error/Warning Behavior 453.
Warning The input signal is lower than 1V/2mA according to
22 -
Analog Input EM-S1INA the operation mode Error/Warning Behavior 453.
Warning A Slave at the system bus signals a fault;
23 -
System bus Warning is only relevant with option EM-SYS.
The DC link voltage has reached the type-
24 - Warning Udc
dependent minimum value.
The Operation Mode 581 for V-belt monitoring
25 - Warning V-belt
signals no-load operation of the application.
Controller Controller is active according to the Operation
30 -
Udc Dynamic Operation Mode 670 for the voltage controller.
The output frequency in the case of a mains failure
31 - Controller Shutdown
is below the Shutdown Threshold 675.
32 - Controller Mains Failure active according to Operation Mode 670 for the
voltage controller.
138 138 Operating

The DC link voltage has exceeded the Reference
33 - Controller Udc Limitation
DC-Link Limitation 680.
Controller The Dyn. Voltage Pre-Control 605 accelerates the
34 -
Voltage Pre-Control control characteristics.
35 - Controller I abs The output current is limited.
Controller The output power or the torque is limited on the
36 -
Torque Limitation speed controller.
Controller Switch-over of field-orientated control between
37 -
Torque Control speed and torque-controlled.
The Operation Mode 620 selected in starting be-
38 - Ramp Stop
havior limits the output current.
Contr. Intel. Curr. Lim. Overload limit of the long-term Ixt (60s) reached,
39 -
LT-Ixt intelligent current limits active.
Contr. Intel. Curr. Lim. Overload limit of the short-term Ixt (1s) reached,
40 -
ST-Ixt intelligent current limits active.
Contr. Intel. Curr. Lim. Max. heat sink temperature TK reached, Operation
41 -
Tc Mode 573 for the intelligent current limits active.
Contr. Intel. Curr. Lim. Max. motor temperature TPTC reached, Operation
42 -
Motor Temp. Mode 573 for the intelligent current limits active.
Controller The reference frequency has reached the Maximum
43 -
Torque Limitation Frequency 419. The frequency limitation is active.
Removal or deactivation of the operation mode
101 to 143
within the warning mask.
The selected warning mask can be read out via the parameter Actual Warning Mask
537. The above operation modes, which can be set in the configurable Create Warn-
ing Mask 536 are encoded in the Actual Warning Mask 537. The code results from
hexadecimal addition of the individual operation modes and the matching abbrevia-
tion.
Warning code Operation mode 536

A FFFF FFFF - 1- Activate everything
A 0000 FFFF - 2- Activate all Warnings
A FFFF 0000 - 3- Activate all Controller States
A 0000 0001 Ixt 10 - Warning Ixt
A 0000 0002 IxtSt 11 - Warning Short-Term Ixt
A 0000 0004 IxtLt 12 - Warning Long-Term Ixt
A 0000 0008 Tc 13 - Warning Heat Sink Temperature
A 0000 0010 Ti 14 - Warning Inside Temperature
A 0000 0020 Lim 15 - Warning Limit
A 0000 0040 INIT 16 - Warning Init
A 0000 0080 MTemp 17 - Warning Motor Temperature
A 0000 0100 Mains 18 - Warning Phase Failure
A 0000 0200 PMS 19 - Warning Motor Protection Switch
A 0000 0400 Flim 20 - Warning Fmax
A 0000 0800 A1 21 - Warning Analog Input MFI1A
A 0000 1000 A2 22 - Warning Analog Input MFI2A
A 0000 2000 Sysbus 23 - Warning System bus
A 0000 4000 UDC 24 - Warning Udc
A 0000 8000 BELT 25 - Warning V-belt
Table "Operation Modes of Warning Mask" continued on next page.

Operating ACTIVE
Warning code Operation mode 536
A 0001 0000 UDdyn 30 - Controller Udc Dynamic Operation
A 0002 0000 UDstop 31 - Controller Shutdown
A 0004 0000 UDctr 32 - Controller Mains Failure
A 0008 0000 UDlim 33 - Controller Udc Limitation
A 0010 0000 Boost 34 - Controller Voltage Pre-Control
A 0020 0000 Ilim 35 - Controller I abs
A 0040 0000 Tlim 36 - Controller Torque Limitation
A 0080 0000 Tctr 37 - Controller Torque Control
A 0100 0000 Rstp 38 - Ramp Stop
A 0200 0000 IxtLtlim 39 - Contr. Intel. Curr. Lim. LT-Ixt
A 0400 0000 IxtStlim 40 - Contr. Intel. Curr. Lim. ST-Ixt
A 0800 0000 Tclim 41 - Contr. Intel. Curr. Lim. Tc
A 1000 0000 MtempLim 42 - Contr. Intel. Curr. Lim. Motor Temp.
A 2000 0000 Flim 43 - Controller Freq. Limitation
14.4 Digital Inputs

The assignment of the control signals to the available software functions can be
adapted to the application in question. Depending on the Configuration 30 selected,
the default assignment or the selection of the operation mode differ. In addition to
the available digital control inputs, further internal logic signals are available as
sources.
The individual software functions are assigned to the various signal sources via pa-
rameterizable inputs. This enables a flexible use of the digital control signals.
Digital Inputs Function

6 - On Signal input is switched on.
7 - Off Signal input is switched off.
Technology Controller Start command technology controller (configura-
13 -
Start tion 111 or 411).
61 - Error Signal Output Monitoring function signals an operational fault.
Signal at digital input S1IND (X210A.3)
70 - S1IND
(controller release linked permanently).
Signal at digital input S2IND (X210A.4) or remote
71 - S2IND
control via communication interface.
72 - S3IND
73 - S4IND
74 - S5IND
Signal at digital input S6IND (X210B.1) or remote
75 - S6IND
Signal at multifunction input MFI1 (X210B.6) in
76 - MFI1D Operation Mode 452 = 3 - digital input or re-
mote control via communication interface.
The defined warnings mask of parameter Create
157 - Warning Mask Warning Mask 536 signals a critical operating
point.
Table "Operation Modes for Digital Control Signals" continued on next page.

Operating ACTIVE
Output signal of the time function according to
158 - Timer 1
the input connection Timer 1 83.
Output signal of the time function according to
159 - Timer 2
the input connection Timer 2 84.
Reference Frequency Signal when the Actual Frequency 241 has
163 -
reached reached the reference frequency.
Signal when the Setting Frequency 510 is smaller
164 - Setting Frequency
than or equal to the Actual Frequency 241.
The monitoring functions report an overload of
165 - Warning Ixt
the frequency inverter.
Warning Max. heat sink temperature TK of 80 °C less the
166 -
Heat sink temperature Warning Limit Heat Sink Temp 407 reached.
Warning Max. inside temperature Ti of 65 °C less the
167 -
Inside temperature Warning Limit Inside Temp. 408 reached.
Warning behavior according to parameterized
Warning
168 - Motor Temp. Operation mode 570 at max. motor
Motor Temperature
temperature TPTC.
Signal when Warnings 269 are displayed with a
169 - General Warning
critical operating point.
The selected limit values Warning Limit Heat Sink
Temp. 407, Warning Limit Inside Temp 408 or
170 - Warning Over temperature
the maximum motor temperature have been ex-
ceeded.
171 - Output Comparator 1
Inverted Output Operation mode 171 with inverted logic
172 -
Comparator 1 (LOW active).
173 - Output Comparator 2
Inverted Output Operation mode 173 with inverted logic
174 -
Comparator 2 (LOW active).
Signal, according to parameterized
175 - Digital Signal 1
Operation Digital Output 1 530.
Signal according to parameterized
176 - Digital Signal 2 Digital Operation 554 at multi-function output
MFO1.
Signal, according to parameterized
177 - Digital Signal 3
Operation Mode Digital Output 3 532.
Reference Percentage High when the Actual Percentage Value 230 has
178 -
Reached reached the Reference Percentage Value 229.
179 - Mains Failure active according to Operation Mode 670 for the
voltage controller.
Warning Parameterized Operation Mode 571 of the motor
180 -
Motor Protection Switch protection switch has triggered.
220 - Logic module 1
221 - Logic module 1 inverted Inverted signal from output of logic module 1.
Table "Operation Modes for Digital Control Signals" continued on next page.

Operating ACTIVE
Operation modes 70 to 76 of the digital inputs
270 to 276
inverted (LOW active).
Reference orientation 469 of axle positioning
282 - Arrived at desired Position
reached.
Signal at digital input 1 of an EM extension mod-
320 - EM-S1IND 2)
ule or remote control via communication interface
321 - EM-S2IND 2)
322 - EM-S3IND 2)
520 - EM-S1IND inverted Operation mode 320 inverted.
525 - S1IND (Hardware) 1) Digital input S1IND (X210A.3).
530 - S6IND (Hardware) 1) Digital input S6IND (X210B.1).
Multifunction input MFI1 (X210B.6) in
531 - MFI1D (Hardware) 1)
Operation Mode 452 = 3 - digital input.
532 - EM-S1IND (Hardware) 1) Digital input 1 of an EM extension module.
Operation modes 525 to 533 of the digital inputs
537 to 545
inverted (LOW active).
Signal if an optional expansion module EM with
700 - RxPDO1 Boolean1 3)
system bus is used.
system bus is used.
system bus is used.
system bus is used.
Operation modes 700 to 703 for RxPDO2 with an
710 to 713 3)
expansion module EM.
Operation modes 700 to 703 for RxPDO3 with an
720 to 723 3)
expansion module EM.
730 - Sysbus Emergency 3)
system bus is used.
1)
The digital signal is independent of the setting of parameter Local/Remote 412.
2)
Refer to operating instructions of extension modules EM-IO
3)
Refer to operating instructions "System bus EM-SYS extension module“
142 142 Operating

14.4.1 Start command
The parameters Start Clockwise 68 and Start Anticlockwise 69 can be linked to the
available digital control inputs or the internal logic signals. The drive is only acceler-
ated according to the control method after a start command.
The logic functions are used for the specification of the direction of rotation, but also
for using the parameterized Operation Mode 620 for the starting behavior and the
Operation Mode 630 for the stopping behavior.
14.4.2 3-Wire-Control
In the case of the 3-wire control, the drive is controlled by means of digital pulses.
The drive is prepared for the start via the logic state of the signal Start 3-Wire Con-
trol 87 and started by a Start Clockwise (Parameter Start Clockwise 68) or a Start
Anti-Clockwise (Parameter Start Anti-Clockwise 69) pulse. The drive is stopped by
switching the signal Start 3-Wire Control 87 off.
The control signals for Start Clockwise and Start Anticlockwise are pulses. The func-
tions Start Clockwise and Start Anticlockwise are latching signals if the signal Start 3-
Wire Control 87 is switched on. The lock is released if the stop signal is switched off.
Machine R R
L 2
1
Start clockwise
Start anticlockwise
Start
t
(R) Clockwise (1) Signals are ignored

(L) Anti-clockwise (2) Time t < 32 msec
The drive is started according to the configured starting behavior when the signal
Start 3-Wire-Control 87 is switched on and a positive signal edge for Start Clockwise
or Start Anti-Clockwise is detected.
Once the drive has been started, new edges (1) on the start signals are ignored.
If the start signal is shorter than 32 msec (2) or if both start signals were switched on
within 32 msec (2), the drive will be stopped according to the configured stopping
behavior.
3-wire control is activated via parameter Local/Remote 412:
Local/Remote 412 Function

Ctrl. 3-Wire, direc- 3-wire; control of direction of rotation and signal
5-
tion Cont. 3-Wire Control 87 via contacts.
Ctrl. 3-Wire + KP, 3-wire and control unit; control of direction of rotation
46 -
Dir. Cont. + KP and signal 3-Wire Control 87 via contacts or control unit.
For further operation modes of parameter Local/Remote 412, refer to Chapter “Bus
controller”.

14.4.3 Error Acknowledgment
The frequency inverters feature various monitoring functions which can be adapted
via the error and warning behavior. Switching the frequency inverter off at the various
operating points should be avoided by an application-related parameterization. If
there is a fault switch-off, this message can be acknowledged via the parameter Pro-
gram(ming) 34 or the logic signal connected with the parameter Error Acknowledg-
ment 103.
14.4.4 Timer
The time functions can be selected via the parameters Operation Mode Timer 1 790
and Operation Mode Timer 2 793. The sources of the logic signals are selected with
the parameters Timer 1 83 and Timer 2 84 and processed according to the config-
ured timer functions.
14.4.5 Thermo-contact
The monitoring of the motor temperature is a part of the error and warning behavior
which can be configured as required. The parameter Thermo contact 204 links the
digital input signal to the defined Motor Temp. Operation Mode 570 which is de-
scribed in chapter "Motor Temperature". The temperature monitoring via a digital
input checks the input signal for the threshold value. Accordingly, a thermo contact or
an additional circuit must be used if a temperature-dependent resistor is used.
14.4.6 n-/M-Control Change-Over

The field-orientated control procedures in configurations 230 and 430 contain the
functions for speed or torque-dependent control of the drive. The change-over can be
done during running operation of the drive, as an additional functionality monitors the
transition between the two control procedures. The speed controller or the torque
controller is active, depending on the n-/M Control Change-Over 164.
144 144 Operating

14.4.7 Data Set Change-Over
Parameter values can be stored in four different data sets. This enables the use of
various parameter values depending on the current operation point of the frequency
inverter.
The change-over between the four data sets is done via the logic signals assigned to
the parameters Data Set Change-Over 1 70 and Data Set Change-Over 2 71.
The actual value parameter Active Data Set 249 shows the selected data set.
Activation
Data Set Change- Data Set Change-
Function/active data set
Over 1 70 Over 2 71
0 0 Data set 1 (DS1)
If Configuration 30 = 110, 111, 410, 411 or 430 is selected, in the factory setting a
timer function is interconnected between the digital input S4IND and the data set
change-over 1.
Timer 1 83
73 - S4IND 158 - Timer 1
P. 83 Data set change-over 1 70
The data set change-over 1 is linked with timer 1.

Data set change-over 1 70 = 158 – Timer 1
Timer 1 is linked with the digital input S4IND (terminal X210A.6)
Timer 1 = 73 – S4IND
In the factory setting the data set change-over 1 is not affected by the Timer 1:
Signal delay Time 1 Timer 1 791 = 0.00 s/m/h
Signal duration Time 2 Timer 1 792 = 0.00 s/m/h

14.4.8 Fixed Value Change-Over
Depending on the selected configuration, the reference values are specified via the
assignment of the Reference frequency source 475 or Reference percentage source
476. Accordingly, there can be a change between the fixed values by way of linking
the logic signals to the parameters Fixed frequency change-over 1 66, Fixed fre-
quency change-over 2 67 or the parameters Fixed percent change-over 1 75, Fixed
percent change-over 2 76.
By combining the logic states of the fixed frequency change-over modes 1 and 2,
Fixed Frequency Control

Fixed Frequency Chan- Fixed Frequency Chan- Function / active fixed value
ge-Over 1 66 ge-Over 2 67
By combining the logic states of the fixed percentage change-over modes 1 and 2,
Fixed Percentage Control

Fixed percentage value Fixed percentage valueFunction / active fixed value
change-over 1 75 change-over 2 76
146 146 Operating

14.4.9 Motor Potentiometer
The parameters Reference Frequency Source 475, and Reference Percentage
Source 476 contain operation modes with motor potentiometer. Operation Mode 474
defines the behavior of the motor potentiometer function and the parameters Fre-
quency Motorpoti Up 62, Frequency Motorpot. Down 63 or Percent Motorpoti
Up 72, Percent Motorpot. Down 73 the link to the available logic signals.
Motor Potentiometer Control

Motorpoti Up Motorpoti Down Function
0 0 Output signal does not change.
1 0 Output value rises at set ramp.
0 1 Output value drops at set ramp.
1 1 Output value is reset to initial value.
14.5 Function Modules
14.5.1 Timer
The timer function can be linked to various functions for time-control of digital signals.
The parameters Operation Mode Timer 1 790 and Operation Mode Timer 2 793
define the evaluation of the digital input signals and the unit of time of the time func-
tion.
Operation mode 790, 793 Function

0 - Off Signal output is switched off.
Positive signal edge starts timer (trigger),
1 - Normal, Rising Edge, Sec. time 1 delays the output signal,
time 2 defines the signal period.
next positive signal edge within time 1 starts the
2 - Retrigger, Rising Edge, Sec.
delay in time again (Retrigger), time 2 defines the
signal period.
if no input signal is received within time 1 the
AND-Connect., Rising Edge,
3- delay starts again (Retrigger),
Sec.
if no input signal is received within time 2, the
signal period is terminated.
Operation modes 1...3, negative signal edge
11 to 13
starts timer.
101 to 113 Operation modes 1...3, [in minutes].
201 to 213 Operation modes 1...3, [in hours].
By default, the functions are linked according to the following illustration:

Timer 1 83
73 - S4IND 158 - Timer 1
P. 83 Data Set Change-Over 1 70
Timer 2 84
175 - Digital signal 1 159 - Timer 2
P. 84

The sources of the digital signals (e.g. 73-S4IND, 175-Digital signal 1) are selected via
the parameters Timer 1 83 and Timer 2 84. Timer 1 is linked to digital input 4 and
Timer 2 is linked to the logic signal digital signal 1.
The output signal of the timer can be assigned via the corresponding parameters of
the operation mode of a digital input or output. By default, Data Set Change-Over 1 is
linked to Timer 1 and Digital Output 1 530 is linked to Timer 2.
14.5.1.1 Time Constant

The logic sequence of input and output signals is to be set separately for both timer
functions via the time constants. The default parameter values result in a direct link of
the input and output signal without a delay.
Note: Before starting the timer, select the operation mode and set the times in
order to avoid non-defined states.
Parameter Settings
791 Time 1 Timer 1, signal delay 0.00 s/m/h 650.00 s/m/h 0.00 s/m/h
792 Time 2 Timer 1, signal duration 0.00 s/m/h 650.00 s/m/h 0.00 s/m/h
794 Time 1 Timer 2, signal delay 0.00 s/m/h 650.00 s/m/h 0.00 s/m/h
795 Time 2 Timer 2, signal duration 0.00 s/m/h 650.00 s/m/h 0.00 s/m/h
Examples of the timer function depending on the selected operation mode and the
input signal:
Normal, positive edge

Parameter Operation mode Timer = 1
Input
Time 1 Time 2
Output
As soon as the positive signal edge is received at the input, time 1 starts. After the
expiry of the delay, the output signal is activated for signal duration time 2.

Retrigger, positive edge
Input
Time 1 Time 1 Time 2
Output
As soon as the positive signal edge is received at the input, time 1 is started. If a posi-
tive signal edge is detected within the delay, time 1 starts again. After the expiry of
the delay, the output signal is switched for the signal duration time 2.
: Time not run out completely

: Time run out completely
AND connection, positive edge

Input
Time 1 Time 1 Time 2
Output
As soon as the positive signal edge is received at the input, time 1 is started. If a posi-
tive signal edge is detected within the delay, time 1 starts again. After the expiry of
the delay, the output signal is switched for the signal duration time 2. Within the sig-
nal duration time 2, the output is switched off by the input signal. If the input signal is
present during the whole time 2, the output signal remains on in this time.
: Time not run out completely
: Time run out completely

14.5.2 Comparator
With the help of software functions Comparator 1 and 2, various comparisons of ac-
tual values with percentage-adjustable fixed values can be done.
The actual values to be compared can be selected from the following table with the
parameters Op. Mode Comparator 1 540 and Op. Mode Comparator 2 543.
If an expansion module is connected, further operation modes are available.
0 - Off Comparator is switched off.
1 - Absolute current R.m.s Current 211 > Rated Current 371.
2 - Abs. Active Current Active Current 214 > Rated Current 371.
Stator Frequency 210 > Maximum Fre-
3- Abs. Stator Frequency
quency 419.
Encoder 1 Speed 218 > maximum speed (cal-
4- Abs. Actual Speed 1 culated from Maximum Frequency 419 and No.
of Pole Pairs 373).
Repetition Frequency Input 252 >Maximum
5- Abs. Actual Repetition Freq.
Frequency 419.
Winding Temp., Winding Temperature 226 >
6-
Temp. Follow-Up. temperature 100 °C.
Actual Frequency 241 > Maximum Fre-
7- Abs. Actual Frequency
quency 419.
9- DC link voltage DC Link Voltage 222 > Direct voltage 1000 V.
10 - Abs. Isq Isq 216 > Rated Current 371.
11 - Abs Filtered Active Current Active Current 214 > Rated Current 371.
Internal Reference Frequency 228 >
12 - Abs. Internal Ref. Frequency
Maximum Frequency 419.
Reference Percentage Value 229 >
13 - Abs. Ref. Percentage Value
Maximum Reference Percentage 519.
Abs. Actual Percentage Actual Percentage Value 230 >
14 -
Value Maximum Reference Percentage 519.
Analog Input
15 - Analog Input MFI1A 251 > input signal 100 %.
MFI1A Abs. Amount
The switch-on and switch-off thresholds for compactors 1 and 2 are set by the pa-
rameters Comparator On above 541, 544 and Comparator Off below 542, 545.
The percentage limits of the corresponding reference values are indicated.
Parameter Settings
541 Comparator 1 On above - 300.00 % 300.00 % 100.00 %
542 Comparator 1 Off below - 300.00 % 300.00 % 50.00 %
544 Comparator 2 On above - 300.00 % 300.00 % 100.00 %
545 Comparator 2 Off below - 300.00 % 300.00 % 50.00 %
150 150 Operating

The setting of the percentage limits of the comparators enables the following logical
links. The comparison with signs is possible in the corresponding operation modes of
the comparators.
1 1
0 0
% %
off on on off
below above above below
14.5.3 Logic Modules

With the Logic Modules function, it is possible to link external digital signals and inter-
nal logic signals of the frequency inverter to one another. Four identical logic modules
are available. These modules can be parameterized independent of one another. The
results of the logic operations can be used for further functions within and outside of
the frequency inverter. In addition to the combinatory logic functions AND, OR and
EXOR, the sequential logic functions RS flip-flop, D flip-flop and Toggle flip-flop are
available.
Each module has two logic inputs and one logic output. The inputs can be parameter-
ized and can be assigned to different signal sources. The signal sources are listed in
the logic table in chapter "Digital Inputs". Additionally, the logic modules can be inter-
connected to each other via the corresponding parameterization. The functionality of
the parameters is the same in each of the four logic modules.
Note: The logic modules are processed internally in the frequency inverter one
after the other depending on their number. For example, logic module 1
is processed before logic module 2.
When designing application-specific logic links, e.g. in the case of time-
critical applications:
− Make sure to comply with the correct order of the logic modules.
− Observe the processing time of 16 ms.
The following table shows the assignment of the parameters to the individual logic
modules:
Module Operation mode Input 1 Input 2

Operation Mode
Logic module 1 Input 1 Logic 1 199 Input 2 Logic 1 200
Logic 1 198
Operation Mode
Logic 2 201
Operation Mode
Logic module 3 Input 1 Logic 3 206 Input 2 Logic 3, 207
Logic 3 205
Operation Mode
Logic 4 503

The parameters Operation Mode Logic 1 198, Operation Mode Logic 2 201, Opera-
tion Mode Logic 3 205 and Operation Mode Logic 4 503 include the following func-
tions:

0 - Off Signal output is switched off.
Input 1 and input 2 are linked to each other via a logic AND
1 - AND
operation.
Input 1 and input 2 are linked to each other via a logic OR
2 - OR
operation.
Input 1 and input 2 are linked to each other via a logic Ex-
3 - XOR clusive OR operation. Output Q will be logic "1" only if differ-
ent logic levels are present at input 1 and input 2.
Input 1 is the set input,
input 2 is the reset input of the RS flip-flop.
Logic "1" at the set input will set output Q to "1". Logic "1"
10 - RS Flip-Flop
at the reset input will set output Q to "0".
If logic "0" is present at both inputs, the output signal is kept
at the last status.
The output signal changes with the positive edge of the clock
20 - Toggle Flip-Flop signal at input 1.
Input 2 is wired internally in this configuration.
If a positive clock edge is received at input 2 (clock pulse
30 - D Flip-Flop input C), the signal present at input 1 (data input D) is
transmitted to output Q.
Examples of the logic functions depending on the selected operation mode:
AND Operation
Parameter Operation Mode Logic = 1
E1 E2 Q E1
E1 0 0 0
& Q 0 1 0 E2
E2 1 0 0
1 1 1 Q
E1: input 1; E2: input 2; Q: output
If logic "1" is present at input 1 and input 2, output Q is logic "1". If both inputs or
either one input are logic "0", output Q will be logic "0", too.

OR Operation
E1 E2 Q E1
E1 0 0 0
>1 Q 0 1 1 E2
=
E2 1 0 1
1 1 1 Q
If logic "1" is present at input 1 or input 2 or at both inputs, output Q is "1". If both
inputs are "0", output Q will be logic "0", too.
EXOR Operation
E1 E2 Q E1
E1 0 0 0
=1 Q 0 1 1 E2
E2 1 0 1
1 1 0 Q
Output Q is logic "1" if inputs 1 and 2 have different logic states. If both inputs have
the same logic state, output Q will be logic "0".

RS Flip-Flop
E1
Q Status
S
E1 S Q 0 0 Qn-1 hold
0 1 0 reset
E2 R 1 0 1 set
1 1 0 off
E1; S
E2; R
E1: set; E2:reset; Q: output
Set: Logic "1" at the set input will set output Q to logic "1".
Store: If a logic "0" is present at the S input, output Q remains unchanged.
Reset: If the R input is set to logic "1", output Q is set to logic "0".
Off: If both inputs are set to logic "1", output Q will be logic "0".
Toggle Flip-Flop
E1
Q Status
T
Q 1 Qn-1 hold
E1 T 0–>1 Qn-1 output invers (toggle)
1–>0 Qn-1 hold
0 Qn-1 hold
E1; T
E1: clock input T; Q: output
The T flip-flop changes its output state with each positive clock edge at input 1 (clock
pulse input T). In all other signal states of the clock input (static logic "0" or logic "1"
or negative clock edge), the output signal remains unchanged.
Note: Input 2 is deactivated in this configuration. A parameterization of input

2 via the corresponding parameters will be have no effect for this rea-
son.
154 154 Operating

D Flip-Flop
E1 Q Status
E1; D D
Q
0 0 Qn-1 hold
E2; C 1 0 Qn-1 hold
0 0–>1 0 sample
1 0–>1 1 sample
E2; C
E1; D
E1: data input D; E2: clock input C; Q: output
If logic "0" is present at input 2 (clock input C), the previous logic state is maintained
at the output independent of the status of input 1 (data input D).
If a positive clock edge is received at clock pulse input C, the signal present at data
input D is transmitted to the output. The output maintains its state Qn-1 until the next
positive clock edge is received.
If a negative clock edge is received, the output signal remains unchanged.

15 V/f - Characteristic
The sensor-less control in configurations 110 and 111 is based on the proportional
change of output voltage compared to the output frequency according to the config-
ured characteristic.
By setting the V/f-characteristic, the voltage of the connected 3-phase motor is con-
trolled according to the frequency. The torque to be applied by the motor at the cor-
responding operating point demands the control of the output voltage proportional to
the frequency. At a constant output voltage / output frequency ratio of the frequency
inverter, the magnetization is constant in the nominal operating range of the 3-phase
motor. The rating point of the motor or end point of the V/f-characteristic is set via
the guided commissioning with the parameter Cut-Off Voltage 603 and the parame-
ter Cut-Off Frequency 604.
The lower frequency range, where an increased voltage is necessary for the start of
the drive, is critical. The voltage at output frequency = zero is set with the parameter
Starting Voltage 600. An increase in voltage deviating from the linear course of the
V/f-characteristic can be defined by the parameters Voltage Rise 601 and Rise Fre-
quency 602. The percentage parameter figure is calculated from the linear V/f-
characteristic. Via the parameters Minimum Frequency 418 and Maximum Frequency
419, the working range of the machine or the V/f-characteristic is defined.
U 418 (FMIN) 419 (FMAX)

Working range
603 (UC)
601 (UK)
600 (US)
602 (FK) 604 (FC) f
(FMIN): Minimum Frequency 418, (FMAX): Maximum Frequency 419,

(US): Starting Voltage 600,
(UK): Voltage Rise 601, (FK): Rise Frequency 602,
(UC): Cut-Fff Voltage 603, (FC): Cut-Off Frequency 604
Parameter Settings
600 Starting Voltage 0.0 V 100.0 V 5.0 V
601 Voltage Rise -100 % 200 % 10 %
602 Rise Frequency 0% 100 % 20 %
603 Cut-Off Voltage 60.0 V 560.0 V 400.0 V
604 Cut-Off Frequency 0.00 Hz 999.99 Hz 50.00 Hz
Note: The guided commissioning takes the parameterized rated motor values
and reference data of the frequency inverter into account when it comes
to pre-setting the V/f-characteristic. In the case of three-phase ma-
chines, the speed can be increased at a constant torque if the motor
winding can be switched over from star to delta connection. If the data
for delta connection indicated on the name plate of the three-phase
motor were entered, the cut-off frequency is increased automatically by
the square root of three.
156 156 Operating

The default Cut-Off Voltage 603 (UC) and Cut-Off Frequency 604 (FC) are derived
from the motor data Rated Voltage 370 and Rated Frequency 375. With the param-
eterized Starting Voltage 600 (US), the linear equation of the V/f-characteristic re-
sults.
⎛ UC − US ⎞ ⎛ 400.0 V - 5.0 V ⎞
U=⎜ ⎟ ⋅ f + US = ⎜ ⎟ ⋅ f + 5.0 V
⎝ FC − 0 ⎠ ⎝ 50.00 Hz − 0.00 Hz ⎠
The Rise Frequency 602 (FK) is entered as a percentage of the Cut-Off Frequency
604 (FC), the default value is f=10 Hz. The output voltage for the default Voltage
Rise 601 (UK) is calculated as U=92.4V.
⎡⎛ UC − US ⎞ ⎤ ⎡⎛ 400 V - 5 V ⎞ ⎤
U = ⎢⎜ ⎟ ⋅ (FK ⋅ FC) + US⎥ ⋅ (1 + UK ) = ⎢⎜ ⎟ ⋅ (0.2 ⋅ 50 Hz ) + 5 V ⎥ ⋅ 1.1 = 92.4 V
⎣⎝ FC − 0 ⎠ ⎦ ⎣⎝ 50 Hz − 0 Hz ⎠ ⎦
15.1 Dynamic Voltage Pre-Control

The Dyn. Voltage Pre-Control 605 accelerates the control behavior of the current
limit controller (parameter Operation Mode 610) and the voltage controller (parame-
ter Operation Mode 670). The output voltage value resulting from the V/f character-
istic is changed by addition of the calculated voltage pre-control.
Parameter Settings
605 Dyn. Voltage Pre-Control 0% 200 % 100 %

Operating ACTIVE
16 Control Functions
The frequency inverters provide a selection of established control methods in Con-
figuration 30. The selected control structure can be parameterized as required and
optimized for the application by further functions.
16.1 Intelligent current limits

The current limits to be set according to the application avoid inadmissible loading of
the connected load and prevent a fault switch-off of the frequency inverter. The func-
tion extends the current controller available in the control system. The overload re-
serve of the frequency inverter can be used optimally by means of the intelligent cur-
rent limits, in particular in applications with dynamic load alternations. The criterion to
be selected via the parameter Operation Mode 573 defines the threshold to the acti-
vation of the intelligent current limit. The parameterized rated motor current or the
reference current of the frequency inverter is synchronized as the limit value of the
intelligent current limits.

0 - Off The function is switched off.
1 - Ixt Limitation to the overload of the frequency inverter (Ixt).
10 - Tc Limitation to the maximum heat sink temperature (TC).
11 - Ixt + Tc Operation mode 1 and 10 (Ixt + TC).
20 - Motor Temp. Limitation to the motor temperature (TMotor).
21 - Motor Temp.+ Ixt Operation mode 20 and 1 (TMotor + Ixt).
30 - Tc + Motor Temp. Operation mode 10 and 20 (TC + TMotor).
Tc + Motor Temp.
31 - Operation mode 10, 20 and (TC + TMotor+ Ixt).
+ Ixt
The threshold value selected via the parameter Operation Mode 573 is monitored by
the intelligent current limits. In the operation modes with motor and heat sink tem-
perature monitoring, the reduction of power selected with the parameter Power Limit
574 is done when the threshold value has been reached. This is achieved by a reduc-
tion of the output current and the speed in motor operation. The load behavior of the
connected machine must be a function of the speed to ensure a sensible use of the
intelligent current limits. The total time of the power reduction as a result of an in-
creased motor or heat sink temperature contains not only the cooling time, but also
the additionally defined Limitation Time 575.
The definition of the power limit should be selected as small as possible in order to
give the drive sufficient time to cool down. The reference value is the nominal power
of the frequency inverter or the set rated power of the motor.
Parameter Settings
574 Power Limit 40.00 % 95.00 % 80.00 %
575 Limitation Time 5 min 300 min 15 min
In the operation modes with overload reserve (Ixt) there is a reduction of the output
current when the threshold value is exceeded, with a distinction being made between
long and short-term overload reserve. After the short-term overload (1 s) has been
used up, the output current is reduced to the long-term overload current matching the
present switching frequency. After the long-term overload current has been used up
(60 s), the output current is reduced to the rated current which also depends on the
switching frequency. If the output current has already been reduced due to the fact
that the long-term overload has used up, the short-term overload is no longer avail-
able even if it has not been used up beforehand. The defined overload reserve (Ixt) of
the frequency inverter is available again after a power reduction lasting 10 minutes.

16.2 Voltage controller
The voltage controller contains the functions necessary for monitoring the DC link
voltage.
− The DC link voltage which rises in generator operation or in the braking process of
the 3-phase machine is controlled to the set limit value by the voltage controller.
− The mains failure regulation uses the rotation energy of the drive to bridge short-
term power failures.
The voltage controller is set with the parameter Operation Mode 670 in accordance
with the application.

0 - Off The function is switched off.
Overvoltage controller switched on,
1 - Udc-Limitation active
with motor chopper.
Mains failure regulation switched on,
2 - Mains Support active
with motor chopper, for quick shutdown.
Udc-Limit. & Mains Overvoltage controller and mains failure regulation
3-
Supp. active switched on, with motor chopper.
Mains Support active, Mains failure regulation switched on,
12 -
Chopper not active without motor chopper.
Udc-Limit. & Mains
Overvoltage controller and mains failure regulation
13 - Supp. active,
switched on, without motor chopper.
without Chopper
The function motor chopper is available in the field-oriented control methods (in con-
figurations 210, 230, 410, 411 and 430).
When an operation mode with motor chopper is selected, set the Trigger Threshold
507 to the Reference DC-Link Limitation 680.
Operation mode Overvoltage control,

Voltage controller: Parameter Operation Mode 670 = 1
Ud, f
Overvoltage controller active
680
Ud
f
421 or 423 681
The overvoltage controller prevents a switch-off of the frequency inverter in generator

operation. The reduction of the drive speed by a ramp gradient selected via the pa-
rameter Deceleration Clockwise 421 or Deceleration Anticlockwise 423 can lead to
an overvoltage in the DC link.

If the voltage exceeds the value set by the parameter Reference DC-Link Limitation
680, the deceleration is reduced in such a way that the DC link voltage is regulated to
the set value. If the DC link voltage cannot be regulated to the set reference value by
the reduction of the deceleration, the deceleration is stopped and the output fre-
quency raised. The output frequency is calculated by addition of the parameter value
Max. Frequency Rise 681 to the frequency at the operating point of the controller
intervention.
Parameter Settings
No. Description ACT Min. Max. Fact. sett.
201 225 387.5 380
680 Reference DC-Link Limitation
401 425 775 760
681 Max. Frequency Rise 0.00 Hz 999.99 Hz 10.00 Hz
Operation mode mains failure regulation.

Voltage controller: Parameter Operation Mode 670 = 2
Ud, f
Ud
672
671
Gradient limited Standard ramp

by 673 or 683 or 674
Mains voltage
Power failure Resumption of power t
With the mains failure regulation, short-term mains failures can be bridged. A mains
failure is recognized if the DC link voltage has fallen below the set value of the pa-
rameter Mains Failure Threshold 671. If a mains failure is recognized, the controller
tries to regulate the DC link voltage to the value set with the parameter Reference
Mains Support Value 672. For this, the output frequency is continuously reduced and
the motor with its rotating masses put into generator operation. The reduction of the
output frequency is done according to the configuration with a maximum of the cur-
rent set by the parameter Gen. Ref. Current Limit 683 or the ramp Mains Support
Deceleration 673.
The threshold values of the voltage controller are calculated starting with the current
DC link voltage leading from the parameters Mains Failure Threshold 671 and Refer-
ence Mains support Value 672.
If the mains voltage is restored before a switch-off is effected by the mains undervolt-
age detection system, the drive is accelerated to its reference frequency at the set
acceleration or according to the parameter Acceleration on Mains Resumption 674. If
the value of parameter Acceleration on Mains Resumption 674 is set to the default
value of 0.00 Hz/s, the drive is accelerated at the values set for the ramp parameters
Acceleration (Clockwise) 420 or Acceleration Anticlockwise 422.

Parameter Settings
671 Mains Failure Threshold -200.0 V -50.0 V -100.0 V
672 Reference Mains Support Value -200.0 V -10.0 V -40.0 V
Note: The frequency inverter reacts to the signals at the control inputs both
when the power failure regulation is switched on and in normal operation.
A control via externally supplied control signals is only possible in the case
of a no-break supply. As an alternative, supply through the frequency
inverter is to be used.
Operation mode mains failure regulation (continued)

Ud, f
676
Ud
672
671
f
673 or 683
675
Mains voltage
Power failure Off t
The DC link voltage which is available in the case of a power failure is supplied by the
motor. The output frequency is continuously reduced and the motor with its rotating
masses is switched over to generator operation. The maximum reduction of the out-
put frequency is done at the current set by the parameter Gen. Ref. Current Limit
683 or the ramp Mains Support Deceleration 673 until the frequency limit Shutdown
Threshold 675 is reached. If the energy of the system for bridging the mains failure is
not sufficient, the delay occurs at maximum ramp gradient as from the Shutdown
Threshold 675.
The time required until the motor has come to a standstill results from the regenera-
tive energy of the system which results in an increase in the DC link voltage. The DC
link voltage set with the parameter Reference Shutdown Value 676 is used by the
voltage controller as a control figure and kept constant. The voltage rise enables op-
timization of the braking behavior and the time until the drive has come to a standstill.
The behavior of the controller can be compared to stopping behavior 2 (Shutdown +
Stop), as the voltage controller brings the drive to a standstill at the maximum decel-
eration ramp and supplies it with the remaining DC link voltage.
If the mains voltage is restored after the shutdown of the drive but before the under-
voltage switch-off has been reached, the frequency inverter signals a fault. The con-
trol unit displays the fault message "F0702".
If the mains failure without shutdown (Shutdown Threshold 675 = 0 Hz) takes so
long that the frequency has been reduced to 0 Hz, the drive is accelerated to the ref-
erence frequency when the mains supply is restored.

If the mains failure with or without shutdown takes so long that the frequency in-
verter shuts off completely (LEDs = OFF), the frequency inverter will be in the
"Standby" state when the mains supply is restored. If the inverter is released again,
the drive will start. If the drive is to start automatically after restoration of the mains
supply and if the inverter is released permanently, Operation Mode 651 of Auto Start
must be switched on.
Parameter Settings
No. Description ACT Min. Max. Fact. sett.
675 Shutdown Threshold 0.00 Hz 999.99 Hz 0.00 Hz
201 225 387.5 365
676 Reference Shutdown Value
401 425 775 730
The voltage controller uses the limit values of the DC link voltage. The frequency
change necessary for this is parameterized by the generator reference current value
or rather the ramp. The Gen. Ref. Current Limit 683 or the ramp Mains Support De-
celeration 673 defines the maximum deceleration of the drive necessary in order to
reach the voltage value Reference Mains Support Value 672. The Acceleration on
Mains Resumption 674 replaces the set values of the ramp parameters Acceleration
(Clockwise) 420 or Acceleration Anticlockwise 422 if the value set in the factory is
changed. The voltage control in a mains failure changes from the frequency limit
Shutdown Threshold 675 from Reference Mains Support Value 672 to the Reference
Shutdown Value 676.
Parameter Settings
683 Gen. Ref. Current Limit 0.0 A o ⋅ IFIN IFIN
673 Mains Support Deceleration 0.01 Hz/s 9999.99 Hz/s 50.00 Hz/s
674 Acceleration on Mains Resumption 0.00 Hz/s 9999.99 Hz/s 0.00 Hz/s
The proportional and integrating part of the current controller can be set via parame-
ters Amplification 677 and Integral Time 678. The control functions are deactivated
by setting the parameters to 0. The controllers are P and I controllers in the corre-
sponding settings.
Parameter Settings
677 Amplification 0.00 30.00 - 1)
678 Integral Time 0 ms 10000 ms - 1)
1)
The factory settings are depending on the selected control function. Corresponding
with the setting of the parameter Configuration 30 the following values are as-
signed:
Configuration 1xx: Amplification 677 = 1.0 / Integral Time 678 = 8 ms
Configuration 2xx; 4xx: Amplification 677 = 2.0 / Integral Time 678 = 23 ms
162 162 Operating

16.3 Technology Controller
The technology controller, the behavior of which corresponds to a PI controller, is
available as an additional function in configuration 111, 211 and 411. The connection
of reference and actual value of the application with the functions of the frequency
inverter enables process control without further components. In this way, applications
such as pressure, volume flow or speed control can be implemented easily.
The configuration of the reference percentage source and the assignment of the ac-
tual percentage source are to be considered.
Structural image: Technology Controller
Technology controller
Reference
percentage source 476
-
Actual values:
Actual percentage value 230
Actual percentage source 478 Reference percentage value 229
For the reference value, the technology controller also demands the assignment of an
analog application value with the parameter Actual Percentage Source 478. The dif-
ference between reference and actual value is used by the technology controller to
control the drive system. The measured actual value is mapped via a signal converter
onto the input signal of the reference percentage source.

The analog signal on the multifunctional input 1 in
1 - Analog Input MFI1A
Operation Mode 452 - analog operation.
Rep. Frequency Input The frequency signal at the digital input according to
32 -
(F3) the selected Operation Mode 496.
Caution! The default assignment of parameter Start clockwise 68 to the logic sig-
nal of the technology controller must be observed:
Start Clockwise 68 = 13 - Technology Controller Start.
This assignment may not be changed. The technology controller becomes
active with the controller release at digital input S1IND.
Structural image: Inputs for Actual Percentage Source
Repetition Frequency Actual Percentage Source 478
Input
0 F3
S2IND 0
f
S3IND
%
S6IND
1
Operation mode 496
Devider 497
MFI1A
Multifunctional Input 0
analog Istwerte:
1
+ Actual Percentage Value 230
MFI1
digital
Operation mode 452

The function selected via the parameter Operation Mode 440 defines the behavior of
the technology controller

The technology controller is switched off, the refer-
0 - Off ence value specification is done via the reference per-
centage channel.
For pressure and volume flow control with linear oper-
1 - Standard
ating behavior and actual value monitoring.
Contents level control at defined motor speed with
2 - Liquid Level 1
actual value missing.
Contents level control at defined motor speed with
3 - Liquid Level 2
actual value missing or high control deviation.
Speed control with analog feedback of the actual
4 - Speed controller
speed.
Indirect volume flow Volume flow control with square rooted actual value.
5-
control
The behavior of the technology controller corresponds to a PI controller with the com-
ponents
− proportional component Amplification 444
− integral component Integral time 445
The sign of the amplification determines the direction of control, i.e. with a rising ac-
tual value and pos. sign of the amplification, the output frequency is reduced (e.g. in
pressure control). With a rising actual value and neg. sign of the amplification, the
output frequency is increased (e.g. in temperature control systems, refrigerating ma-
chines, condensers).
The integral component can be used to reduce the steady-state control deviation (de-
viation between actual value and reference value) over a period of time. If the inte-
gral component is too dynamic1) the system will be unstable and oscillates. If the in-
tegral component is too passive2) the steady-state control deviation will not be cor-
rected adequately.
Therefore the integral component must be adjustet installation-dependent.
1)
Dynamic behavior: fast correction of deviations.
2)
Passive behavior: slow correction of deviations.
Parameter Max. P-Component 442 limits the frequency change at the controller out-
put. This prevents oscillations of the system at steep acceleration ramps.
Via Parameter Hysteresis 443 changes of the integral component in a specified range
(hysteresis band) can be rejected. This causes more passiv behavior of the technology
controller and helps to filter noise signals of the controller actual value and to mini-
mize control corrections.
f
Hysteresis 443
Parameter Settings
441 Fixed Frequency -999.99 Hz +999.99 Hz 0.00 Hz
442 max. P-Component 0.01 Hz 999.99 Hz 50.00 Hz
443 Hysteresis 0.01 % 100.00 % 10.00 %
444 Amplification -15.00 +15.00 1.00
446 Ind. Volume Flow Control Factor 0.10 2.00 1.00

Note: The parameterization of the technology controller in the individual data
sets enables an adaptation to various operating points of the application
with the data set change-over via control contacts.
Operation mode standard, parameter Operation Mode 440 = 1

This operation mode can be used, for example, for pressure or volumetric flow control
with linear operation behavior.
The minimum value monitoring prevents an acceleration of the drive if the actual
value is missing.
If the actual value is missing (< 0.5%) the output frequency is guided to the Mini-
mum frequency 418. This is done using the set Deceleration (clockwise) 421.
If the actual value is available again, the controller continues operation automatically.
Limitation
+
Difference
0
1
I-Component
Max.
Max. P-Component
Integral Time 445

I
Amplification 444
Minimum value
> 0.50%
P
-
+
< 0.50%
Ref. Percentage
Act. Percentage
P.478
Ref. Percentage
Technology
Frequency
Source 478
Controller
Source 476
Channel
Fixed

Operation mode filling level 1, parameter Operation Mode 440 = 2
This operation mode can be used, for example, for contents level control.
If the actual value is missing, the function brings the output frequency to an adjust-
able value.
value is missing.
If the actual value is missing (< 0.5%) the output frequency is guided to the Fixed
frequency 441. This is done using the set Deceleration (clockwise) 421.
The Fixed frequency 441 must be in the range between Minimum frequency 418 and
Maximum frequency 419. If the Fixed frequency 441 is set to a value smaller than
the Minimum frequency 418, the output frequency is guided to Minimum frequency
418. The frequency will not drop below Minimum frequency 418.
If the actual value is available again, the controller continues operation automatically.
Limitation
+
I-Component
Max.
Max. P-Component
Integral Time 445

I
Amplification 444
Minimum value
> 0.50%
P
-
+
< 0.50%
Ref. Percentage
Act. Percentage
P.478
Ref. Percentage
Technology
Frequency
Source 478
Controller
Source 476
Channel
Fixed

Operation mode filling level 2, parameter Operation Mode 440 = 3
This operation mode can be used, for example, for contents level control.
value is missing.
If the actual value is missing (< 0.5%) the output frequency is guided to the Fixed
frequency 441. This is done using the set Deceleration (clockwise) 421.
If there is no control deviation (actual value =reference value) or if the control devia-
tion is negative (actual value>reference value), the output frequency is guided to
Minimum frequency 418. This is done using the set Deceleration (clockwise) 421.
The drive accelerates as soon as an actual value is present again or the control devia-
tion exceeds the positive Hysteresis 443. The drive stops as soon as the the control
deviation falls below the negative Hysteresis 443. Limitation
+
I-Component
Max.
Max. P-Component
Integral Time 445

I
Amplification 444
P
Minimum value
> 0.50%
Difference
0
1
-
+
< 0.50%
Ref. Percentage
Act. Percentage
P.478
Ref. Percentage
Technology
Frequency
Source 478
Controller
Source 476
Channel
Fixed

Operation mode speed controller, parameter Operation Mode 440 = 4
This operation mode is suited for speed controls with an analog actual value transmit-
ter (e.g. analog speedometer via analog input or HTL encoder via frequency input).
The motor is accelerated or decelerated according to the control deviation.
The output frequency is limited by the Maximum frequency 419.
Limitation
+
I-Component
Max.
Max. P-Component
Integral Time 445

I
Amplification 444
P
-
+
Act. Percentage
Ref. Percentage
Technology
Ref. Percentage
Source 478
Controller
Source 476
Channel

Operation mode indirect volume flow control,
parameter Operation Mode 440 = 5
This operation mode is suitable for volume flow control based on pressure measure-
ment.
The square rooted actual value enables, for example, direct measurement of the ac-
tive pressure in the system via the intake nozzle of the fan. The active pressure has a
square proportion to the volume flow and thus forms the control figure for the volume
flow control. The calculation corresponds to the "Law of Proportionality" which is gen-
erally valid for centrifugal machines.
Adaptation to the application in question and measurement are done via the Ind. vol-
ume flow control factor 446. The actual values are calculated from the system data to
be parameterized, reference pressure and volume flow, according to the bad point
method, as described in chapter "Volume Flow and Pressure".
The output frequency is limited by the Minimum frequency 418 and Maximum fre-
quency 419.
Limitation
+
I-Component
Max.
Max. P-Component
Integral Time 445

I
Amplification 444
P
Volume flow
-
+
Ref. Percentage
Act. Percentage
Ref. Percentage
Technology
Source 478
Controller
Source 476
Channel

Structural image: Indirect volume flow control
Technology controller
Reference percentage source 476

-
Ind. volume flow control factor 446 x Actual values:

Volumetric flow 285
Pressure 286
Actual percentage source 478

16.4 Functions of Sensorless Control
The configurations of the sensor-less control contain the following additional func-
tions, which supplement the behavior according to the parameterized V/f characteris-
tic.
16.4.1 Slip compensation

The load-dependent difference between the reference speed and the actual speed of
the 3-phase motor is referred to as the slip. This dependency can be compensated by
the current measurement in the output phases of the frequency inverter.
The activation of Operation Mode 660 for the slip compensation enables speed con-
trol without feedback. The stator frequency and speed are corrected depending on the
load. Before the slip compensation can be activated, the guided commissioning has to
be carried out. The Stator Resistance 377 is required to ensure a correct function and
is measured during the guided commissioning.

0 - Off The slip compensation is deactivated.
1 - Switched on The load-dependent slip speed is compensated.
The control behavior of the slip compensation can only be optimized via the parame-
ters in the case of specific applications. The parameter Amplification 661 determines
the correction of the speed and the effect of the slip compensation proportionally to
the change of load. The Max. Slip Ramp 662 defines the max. frequency change per
second in order to avoid an overload in the case of a load change.
The parameter Minimum Frequency 663 determines the frequency as from which the
slip compensation becomes active.
Parameter Settings
661 Amplification 0.0 % 300.0 % 100.0 %
662 Max. Slip Ramp 0.01 Hz/s 650.00 Hz/s 5.00 Hz/s
663 Minimum Frequency 0.01 Hz 999.99 Hz 0.01 Hz
16.4.2 Current limit value controller

Via a load-dependent speed control, the current limit controller ensures that the drive
system is not overloaded. This is extended by the intelligent current limits described in
the previous chapter. The current limit value controller reduces the load on the drive,
e.g. during acceleration, by stopping the acceleration ramp. The switch-off of the
frequency inverter which happens when the acceleration ramps have been set at an
excessive gradient is prevented in this way.
The current limit value controller is switched on and off via parameter Operation
Mode 610.
The current limit controller functions and the intelligent
0 - Off
current limits have been deactivated.
1 - Switched on The current limit controller is active.
Behavior in motor operation:
If the current set via parameter Current Limit 613 is exceeded, the activated current
limit controller will reduce the output frequency until the current limit is no longer
exceeded. The output frequency is reduced, as a maximum, to the frequency set by
parameter Frequency Limit 614. If the current is below the Current Limit 613, the
output frequency increases to the reference value again.

Behavior in generator operation:
If the current set via parameter Current Limit 613 is exceeded, the activated current
limit controller will increase the output frequency until the current limit is no longer
exceeded. The output frequency is increased, as a maximum, to the set Maximum
Frequency 419. If the current is below the Current Limit 613, the output frequency
is reduced to the required reference value again.
Parameter Settings
613 Current Limit 0.0 A o ⋅ IFIN o ⋅ IFIN
614 Frequency Limit 0.00 Hz 999.99 Hz 0.00 Hz
The control behavior of the current limit controller can be set via the proportional
component, parameter Amplification 611, and the integrating component, parameter
Integral Time 612. If an optimization of the controller parameters is necessary in
exceptional cases, a setting should be done by changing parameter Current Limit
613abruptly.
Parameter Settings
611 Amplification 0.01 30.00 1.00
Note: The dynamics of the current limit value controller and the voltage control-
ler is influenced by the setting of the parameter Dyn. Voltage Pre-Control
605.
16.5 Functions of Field-Orientated Control

The field-orientated control modes are based on a cascade control and the calculation
of a complex machine model. In the course of the guided commissioning, a map of
the connected machine is produced by the parameter identification and transferred to
various parameters. Some of these parameters are visible and can be optimized for
various operating points.
16.5.1 Current Controller

The inner control loop of the field-orientated control consists of two current control-
lers. The field-orientated control thus impresses the motor current into the machine
via two components to be controlled.
This is done by:
− controlling the flux-forming current value Isd
− controlling the torque-forming current value Isq
By separate controlling of these two parameters, a decoupling of the system equiva-
lent to an externally excited direct current machine is achieved.
The set-up of the two current controllers is identical and enables joint setting of am-
plification as well as the integral time for both controllers. For this, the parameters
Amplification 700 and Integral Time 701 are available. The proportional and integra-
tion component of the current controllers can be switched off by setting the parame-
ters to zero.
Parameter Settings
700 Amplification 0.00 8.00 0.13
701 Integral Time 0.00 ms 10.00 ms 10.00 ms

Operating ACTIVE
The guided commissioning has selected the parameters of the current controller in
such a way that they can be used without having to be changed in most applications.
If, in exceptional cases, an optimization of the behavior of the current controllers is to
be done, the reference value step-change during the flux-formation phase can be
used for this. If parameterized appropriately, the reference value of the flux-forming
current components jumps to the value Current During Flux-Formation 781 and
then changes in a controlled way to the magnetizing current after the expiry of the
Maximum Flux-Formation Time 780. The operating point necessary for the adjust-
ment demands the setting of parameter Minimum Frequency 418 to 0.00 Hz, as the
drive is accelerated after magnetizing. The measurement of the step response, which
is defined by the ratio of the currents mentioned, should be done in the motor supply
line by means of a measuring current transformer of a sufficient bandwidth.
Note: The internally calculated actual value for the flux-forming current compo-
nent cannot be output via the analog output for this measurement as the
time resolution of the measurement is not sufficient.
To set the parameters of the PI controller, the Amplification 700 is increased first
until the actual value overshoots distinctly during the control process. Now, the ampli-
fication is reduced to about a half again and then the Integral Time 701 is synchro-
nized until actual value overshoots slightly during the control process.
The settings of the current controllers should not be too dynamic in order to ensure a
sufficient reserve range. The control tends to increased oscillations if the reserve
range is reduced.
The dimensioning of the current controller parameters by calculation of the time con-
stant is to be done for a switching frequency of 2 kHz. For other switching frequen-
cies, the values are adapted internally so that the setting can remain unchanged for
all switching frequencies. The dynamic properties of the current controller improve if
the switching and scanning frequency increases.
The fixed time interval for the modulation results in the following scanning frequencies
of the current controller via parameter Switching Frequency 400.
Settings
Switching frequency Scanning Frequency
2 kHz 1) 2 kHz
4 kHz 4 kHz
8 kHz 8 kHz
12 kHz 8 kHz
16 kHz 8 kHz
1)
This switching frequency can only be set for the parameter Min. Switching Fre-
quency 401.

16.5.2 Torque Controller
The torque-controlled configurations 230 and 430 often demand limitation of the
speed in the operating points without load moment. The controller increases the
speed in order to reach the reference torque until the Frequency Upper Limit 767 or
the Frequency Lower Limit 768 is reached. As from the limit value the drive is con-
trolled to maximum speed, which corresponds to the behavior of the speed controller.
Thus, the controller is limited to the Maximum Frequency 419.
Parameter Settings
767 Frequency Upper Limit -999.99 Hz 999.99 Hz 999.99 Hz
768 Frequency Lower Limit -999.99 Hz 999.99 Hz 999.99 Hz
16.5.2.1 Limit Value Sources

The limitation of the frequency can be done by setting fixed values and also by linking
to an analog input parameter. The analog value is limited via parameters Minimum
Reference Percentage 518 and Maximum Reference Percentage 519, but does not
consider the Gradient Percentage Ramp 477 of the reference percentage value chan-
nel.
The assignment is done for the torque controller via parameters Frequency Upper
Limit Source 769 and Frequency Lower Limit Source 770.

The source is the multifunctional input 1 in an
analog Operation Mode 452.
The selected parameter values are taken into
110 - Fixed Limit
account to limit the speed controller.
201 - Inv. Analog Input MFI1A Operation mode 101, inverted.
210 - Inv. Fixed Limit Operation mode 110, inverted.
174 174 Operating

16.5.3 Speed controller
The source of the actual speed value is selected via parameter Actual Speed
Source 766. By default, speed sensor 1 is used as the actual speed source. If speed
sensor 2 of an extension module is to deliver the actual value signal for the speed
controller, speed sensor 2 must be selected as the source.
Actual Speed Source 766 Function

The actual speed source is speed sensor 1 of the
1 - Speed Sensor 1
basic device (factory setting).
The actual speed source is speed sensor 2 of an
2 - Speed Sensor 2
extension module.1)
1)
Only available if extension module is installed
The control of the torque-forming current components is done in the outer control
loop by the speed controller. Via parameter Operation Mode 720, you can select the
operation mode for the speed controller. The operation mode defines the use of the
parameterizable limits. These are referred to the direction of rotation and the direc-
tion of the torque and depend on the selected configuration.

The controller is deactivated or the torque-forming
0 - Speed Controller Off
component is zero.
The limitation of the speed controller assigns the up-
per limit to the motor operation of the drive. Inde-
Limits for
1- pendent of the direction of rotation, the same limit is
Motor / Generator
used. The same applies in the case of regenerative
operation with the lower limit.
The assignment of the limit is done by the sign of the
value to be limited. Independent of the motor or gen-
Limits for
2- erator operating points of the drive, the positive limi-
pos. / neg. Torque
tation is done by the upper limit. The lower limit is
regarded as a negative limitation.

Operation mode 2
anticlockwise clockwise anticlockwise clockwise
generator motor generator motor
n n
motor generator motor generator
Current limit 728

Current limit generator op. 729
The properties of the speed controller can be adapted for adjustment and optimization
of the controller. The amplification and integral time of the speed controller are to be
set via parameters Amplification 1 721 and Integral Time 1 722. For the second
speed range, parameters Amplification 2 723, Integral Time 2 724 can be set. The
distinction between the speed ranges is done by the value selected via parameter
Speed Control Switch-Over Limit 738. The parameters Amplification 1 721 and In-
tegral time 1 722 are taken into account in the case of the default parameter Speed
Control Switch-Over Limit 738. If parameter Speed Control Switch-Over Limit 738
is set to a value higher than 0.00 Hz, parameters Amplification 1 721, Integral Time
1 722 are active below the limit and parameters Amplification 2 723, Integral Time 2
724 are active above the limit.
The parameterized amplification at the current operating point can additionally be
assessed via the parameter Backlash Damping 748 depending on the control devia-
tion. In particular the small signal behavior in applications with a gearbox can be im-
proved by a value higher than zero percent.
The parameter Backlash damping 748 is available depending on the device type.
Parameter Settings
721 Amplification 1 0.00 200.00 - 1)
722 Integral Time 1 0 ms 60000 ms - 1)
723 Amplification 2 0.00 200.00 - 1)
724 Integral Time 2 0 ms 60000 ms - 1)
738 Speed Control Switch-Over Limit 0.00 Hz 999.99 Hz 55.00 Hz
748 Backlash Damping 0% 300 % 100 %
1)
The default setting is relative to the recommended machine data for the amplifica-
tion and integral time. This enables a first function test in a large number of appli-
cations. The distinction of the parameter settings 1 or 2 for the current frequency
range is done by the software according to the selected limit value.
The optimization of the speed controller can be done with the help of a reference
value step-change. The amount of the step-change is defined by the set ramp or limi-
tation. The optimization of the PI controller should be done at the maximum admissi-
ble reference value change rate. First, the amplification is increased until the actual
value overshoots distinctly during the control process. This is indicated by a strong
oscillation of the speed and by the running noises. In the next step, reduce the ampli-
fication slightly (1/2 ...3/4 etc.). Then reduce the integral time (larger I component)
until the actual value overshoots only slightly in the control process.
If necessary, check the speed control settings in the case of dynamic operations (ac-
celeration, deceleration). The frequency at which a switch-over of the controller pa-
rameters is effected can be set via parameter Speed Control Switch-Over Limit 738.

16.5.3.1 Limitation of Speed Controller
The output signal of the speed controller is the torque-forming current component
Isq. The output and the I component of the speed controller can be limited via pa-
rameters Current Limit 728, Current Limit Generator Operation 729, Torque Limit
730, Torque Limit Generator Operation 731 or Power Limit 739, Power Limit Gen-
erator Operation 740. The limits of the proportional component are set via parameter
P-Comp. Torque Upper Limit 732 and parameter P-Comp. Torque Lower Limit 733.
− The output value of the controller is limited by an upper and a lower current limit,
parameter Current Limit 728 and parameter Current Limit Generator Op. 729.
The limit values are entered in Amperes. The current limits of the controller can
be linked to the fixed limits and analog input parameters. The assignment is done
via the parameters Isq Limit Source Motor Op. 734 and Isq Limit Source Gen-
erator Op. 735.
− The output value of the controller is limited by an upper and a lower torque limit,
parameter Torque Limit 730 and parameter Torque Limit Generator Op.. 731.
The limit values are input as a percentage of the rated motor torque. The assign-
ment of fixed values or analog limit values is done via the parameters Torque
Limit Source Motor Op. 736 and Torque Limit Source Gen. Op 737.
− The output value of the P component is limited with parameter P-Comp. Torque
Upper Limit 732 and P-Comp. Torque Lower Limit 733. The limit values are in-
put as torque limits as a percentage of the rated motor torque.
− The power output by the motor is proportional to the product of speed and
torque. This output power can be limited at the controller output with a Power
Limit 739 and Power Limit Generator Operation 740. The power limits are en-
tered in kW.
Parameter Settings
728 Current Limit 0.0 A o ⋅ IFIN o ⋅ IFIN
729 Current Limit Generator Operation -0.1 A o ⋅ IFIN o ⋅ IFIN
730 Torque Limit 0.00 % 650.00 % 650.00 %
731 Torque Limit Generator Operation 0.00 % 650.00 % 650.00 %
732 P-Comp. Torque Upper Limit 0.00 % 650.00 % 100.00 %
733 P-Comp. Torque Lower Limit 0.00 % 650.00 % 100.00 %
739 Power Limit 0.00 kW 2⋅o⋅PFIN 2⋅o⋅PFIN
740 Power Limit Generator Operation 0.00 kW 2⋅o⋅PFIN 2⋅o⋅PFIN
Anticlockwise Clockwise
operation operation
M
Torque Limit Generator

Operation 731 Torque Limit 730
generator motor
motor generator n
Torque Limit Generator

Torque Limit 730 Operation 731
Speed is limited by
Maximum Frequency 419

16.5.3.2 Limit Value Sources
As an alternative to limiting the output values by a fixed value, linking to an analog
input value is also possible. The analog value is limited via parameters Minimum Ref-
erence Percentage 518 and Maximum Reference Percentage 519, but does not con-
sider the Gradient Percentage Ramp 477 of the reference percentage value channel.
The assignment is done with the help of the parameters Isq Limit Source Motor Op-
eration 734 and Isq Limit Source Generator Op. 735 for the torque-forming current
component Isq.
The sources for torque limits are selectable via parameters Torque Limit Source Mo-
tor Op 736 and Torque Limit Source Gen. Op.737

The source is the multifunctional input 1 in an
analog Operation Mode 452.
The frequency signal on the repetition frequency
105 - Rep. Frequency Input (F3)
input corresponding to Operation Mode 496.
The selected parameter values for limiting the
110 - Fixed Limit
speed controller are taken into account.
Note: The limit values and assignment to different limit value sources are data
set related in the configurations. The use of the data set change-over
demands an examination of the parameters in question.
16.5.4 Acceleration Pre-Control

The acceleration pre-control is active in the speed-controlled configurations and can
be activated via parameter Operation Mode 725 for acceleration pre-control.

0 - Off The control system is not influenced.
The acceleration pre-control is active according to
1 - Switched on
the limit values.
The acceleration pre-control controlled parallel to the speed controller reduces the
reaction time of the drive system to a change of reference values. The minimum ac-
celeration time defines the modification speed of the reference speed value as from
which a torque necessary for acceleration of the drive is pre-controlled. The accelera-
tion of the mass is a function of the Mech. Time Constant 727 of the system. The
value calculated from the increase of the reference value and the multiplication factor
of the torque required is added to the output signal of the speed controller.
Parameter Settings
726 Minimum Acceleration 0.1 Hz/s 6500.0 Hz/s 1.0 Hz/s
727 Mech. Time Constant 1 ms 60000 ms 10 ms
For optimal setting, the acceleration pre-control is switched on and the mechanical
time constant is set to the minimum value. The output value of the speed controller is
compared to the minimum acceleration time during the acceleration processes. The
frequency ramp is to be set to the highest value occurring in operation at which the
output value of the speed controller is not yet limited. Now, the value of the Minimum
Acceleration 726 is set to half the set acceleration ramp so that it is ensured that the
acceleration pre-control is active. The acceleration pre-control is not raised by increas-
ing the Mech. Time Constant 727 until the output values corresponds to the time
modification of the drive during the acceleration processes.
178 178 Operating

16.5.5 Field Controller
The flux-forming current component is controlled by the field controller. The guided
commissioning optimizes the parameters of the field controller by measuring the time
constant and magnetizing curve of the connected 3-phase machine. The parameters
of the field controller are selected such that they can be used without changes in most
applications. The proportional and the integrating part of the field controller are to be
set via parameters Amplification 741 and Integral Time 742.
Parameter Settings
717 Reference Flux 0.01 % 300.00 % 100.00 %
741 Amplification 0.0 100.0 5.0
Optimization of the controller parameters of the field parameter should be done in the
basic speed range. The frequency to be set should be slightly lower than the limit of
the modulation controller selected via parameter Reference Modulation 750 so that
the modulation controller is not active. Optimization of the Reference Flux 717 is only
required in exceptional cases. The set percentage value changes the flux-forming
current component proportionally to the torque-forming current component. The cor-
rection of the rated magnetizing current by means of the reference flux thus changes
the torque of the drive. If the parameter Reference Flux 717 is decreased drastically
(change-over from 100% to 50%), the parameter Isd can be oscillographed. The
course of the signal of the flux-forming current Isd should reach the stationary value
after overshooting without oscillation. The integral time of the field controller should
be selected according to the half rotor time constant calculated by the software. The
actual value to be read out via parameter Act. Rotor Time Constant 227 divided by
two is to be used in the first approach for the parameter Integral Time Field Control-
ler 742. If a quick transition into field weakening is necessary for the application, the
integral time should be reduced. The amplification is to be selected relatively large in
order to achieve a good dynamics of the controller. Attention should be paid to the
fact that an increased overshoot is necessary for a good control behavior in controlling
of a load with low-pass behavior, for example a 3-phase machine.

16.5.5.1 Limitation of field controller
The output signal of the field controller, the integrating and proportional components
are limited via parameter Ref. Isd Upper Limit 743 and parameter Ref. Isd Lower
Limit 744. The guided commissioning has set the parameter Ref. Isd Upper Limit
743 according to the parameter Rated Current 371.
Parameter Settings
743 Ref. Isd Upper Limit 0.1⋅IFIN o ⋅ IFIN IFIN
744 Ref. Isd Lower Limit - IFIN IFIN 0.0
The limits of the field controller define not only the maximum current occurring, but
also the dynamic properties of the controller. The upper and lower limits restrict the
modification speed of the machine flux and the torque resulting from it. In particular
the speed area above the nominal frequency should be observed for the modification
of the flux-forming component. The upper limit is to be estimated from the product of
the set magnetizing current and the correction factor Reference Flux 717, although
the limit must not exceed the overload current of the drive.
16.5.6 Modulation Controller

The modulation controller, which is designed as an I regulator, automatically adapts
the output value of the frequency inverter to the machine behavior in the basic speed
area and in the field weakening area. If the modulation exceeds the value set with
parameter Reference Modulation 750, the field-forming current component and thus
the flux in the machine are reduced.
In order to make the best possible use of the voltage available, the figure selected via
parameter Operation mode 753 is put into proportion to the DC link voltage. That
means that with a high mains voltage there is also a high output voltage available, the
drive only reaches the field weakening area later and produces a higher torque.

The modulation is calculated from the ratio of torque-
0 - Usq-Control
forming voltage component Usq to the DC link voltage.
V-Absolute Value The modulation is calculated from the absolute voltage
1-
Control value to the DC link voltage ratio.
The integrating part of the modulation controller is to be set via parameter Integral
Time 752.
Parameter Settings
750 Reference Modulation 3.00 % 105.00 % 102.00 %
180 180 Operating

The percentage setting of the Reference Modulation 750 is basically depending on
the leakage inductivity of the machine. The default value was selected such that in
most cases the remaining deviation of 5% is sufficient as a reserve range for the cur-
rent controller. For the optimization of the controller parameters, the drive is acceler-
ated with a flat ramp into the area of field weakening, so that the modulation control-
ler intervenes. The limit is set via parameter Reference Modulation 750. Then, the
control loop can be excited with a unit step function by modifying the reference
modulation (change-over between 95% and 50%). By means of an oscillographed
measurement of the flux-forming current component on the analog output of the fre-
quency inverter, the controlling process of the modulation controller can be assessed.
The course of the signal of the flux-forming current Isd should reach the stationary
value after overshooting without oscillation. An oscillating of the course of the current
can be damped by increasing the integral time. The parameter Integral Time 752
should roughly correspond to the actual value Act. Rotor Time Constant 227.
16.5.6.1 Limitation of Modulation Controller

The output signal of the modulation controller is the internal reference flux. The con-
troller output and the integrating part are limited via the parameter Reference Imr
Lower Limit 755 and the product of Rated Magnetizing Current 716 with Reference
Flux 717. The magnetizing current parameter forming the upper limit is to be set to
the rated value of the machine. For the lower limit, select a value which also builds up
an adequate flux in the machine in the field weakening area. The limitation of the
control deviation at the output of the modulation controller prevents a possible oscilla-
tion of the control loop in the case of load surges. The parameter Control Deviation
Limitation 756 is stated as an absolute value and acts both as a positive and a nega-
tive limit.
Parameter Settings
755 Reference Imr Lower Limit 0.01⋅IFIN o ⋅ IFIN 0.01⋅IFIN
756 Control Deviation Limitation 0.00 % 100.00 % 10.00 %

17 Special Functions
The configurable functions of the corresponding control methods enable another field
of application of the frequency inverters. The integration in the application is made
easier by special functions.
17.1 Pulse Width Modulation

The motor noises can be reduced by changing over the parameter Switching Fre-
quency 400. The maximum reduction of the switching frequency should not exceed a
ratio of 1:10 to the frequency of the output signal for a sine-shaped output signal. The
maximum possible switching frequency depends on the drive output and the ambient
conditions. For the required technical data refer to the corresponding table and the
device type diagrams.
Parameter Settings
2 kHz 1)
400 Switching frequency 2 kHz 16 kHz
4 kHz 2)
The factory setting of parameter Switching frequency 400 depends on the setting of parameter
Configuration 30:
1)
configurations 1xx
2)
configurations 2xx / 4xx/ 5xx
The heat losses increase proportionally to the load point of the frequency inverter and
the switching frequency. The automatic reduction adjusts the switching frequency to
the current operating state of the frequency inverter in order to provide the output
performance required for the drive task at the greatest possible dynamics and a low
noise level.
The switching frequency is adjusted between the limits which can be set via parame-
ters Switching frequency 400 and Min. Switching Frequency 401. If the Min. Switch-
ing Frequency 401 is larger than or equal to the Switching Frequency 400, the
automatic reduction is deactivated.
Parameter Settings
401 Min. Switching Frequency 2 kHz 16 kHz 2 kHz
The change of the switching frequency depends on the heat sink temperature switch-
off limit and the output current.
The temperature limit to be exceeded so that the switching frequency is reduced can
be set via parameter Reduction Limit Heat Sink Temp. 580. If the heat sink tempera-
ture falls below the threshold set via parameter Reduction Limit Heat Sink Temp. 580
by 5 °C, the switching frequency is increased again step by step.
Parameter Settings
580 Reduction Limit Heat Sink Temp. -25 °C 0 °C -4 °C
Note: The limit for the switching frequency reduction is influenced by the
intelligent current limits depending on the selected Operation Mode
573 and the output current. If they have been switched off or provide
the full overload current, the switching frequency is reduced when the
output current exceeds the limit of 87.5% of the long-term overload
current (60s). The switching frequency is increased if the output cur-
rent drops below the reference current of the next highest switching
frequency.

17.2 Fan
The switch-on temperature of the heat sink fan can be set with the parameter Switch-
on temperature 39.
If mains voltage is applied to the frequency inverter, and the heat sink temperature
exceeds the set temperature, the heat sink fan is switched on. Independent from pa-
rameter Switch-on temperature 39, the heat sink fan will be switched on, as soon as
the frequency inverter is switched on and enabled and the start signal is received.
If the heat sink temperature drops below the set temperature by 5 °C, or if the con-
troller enable signal is inhibited, the heat sink fan is switched off when the minimum
ON-time has elapsed.
The minimum ON-time of the heat sink fan is set internally to 1 minute. When the
temperature drops below the Switch-on temperature 39 during this time since start-
ing, the fan will continue to operate until the running ON-time is reached.
Operation mode 43 for digital outputs additionally enables the control of an exter-
nal fan. Via the digital output, the fan is switched on if the controller is released and
Start clockwise or Start anticlockwise are switched on, or if the Switch-on temperature
39 for the internal fan was reached.
Like in the case of the internal heat sink fan, the minimum ON-time of the external fan
is 1 minute.
Parameter Settings
39 Switch-On Temperature 0 °C 60 °C 0 °C
17.3 Bus controller

Note: In order to be able to control the drive, the digital controller input S1IND
must be connected and set to "High-Signal" in order to enable the out-
put stage.
terminal S1IND.
time. Wait for some minutes until the DC link capacitors have dis-
charged before starting to work at the unit.
The frequency inverters can be extended by different options for data communication
and can be integrate in an automation and control system in this way. Parameteriza-
tion and commissioning can be done via the optional communication card, the operat-
ing unit or the interface adapter. The parameter Local/Remote 412 defines the oper-
ating behavior and enables a change between the control via contacts or the control
unit and/or the interface.

Local/Remote 412 Function
Control via The Start and Stop commands as well as the direction of
0-
Contacts rotation are controlled via digital signals.
The Start and Stop commands as well as the direction of
Control via
1- rotation are controlled via the DRIVECOM State machine
Statemachine
of the communication interface.
Control via
2- rotation are controlled via logic signals through the
remote contacts
communication protocol.
Control via Keypad, The Start and Stop commands are controlled from the
3 - direction of rot. via control unit and the direction of rotation is controlled via
contacts digital signals.
Cont. via KP or Cont., The Start and Stop commands are controlled from the
4 - direction of rot. via control unit or via digital signals. The direction of rota-
cont. tion is controlled via digital signals only.
Ctrl. 3-Wire, direction 3-wire; control of direction of rotation and signal
5-
Cont. 3-Wire Control 87 via contacts.
Control via KP,
13 - direction of rot. via
rotation are controlled via the control unit.
KP
Control via KP +
The Start and Stop commands are controlled from the
cont.,
14 - control unit or via digital signals. The direction of rota-
direction of rot. via
tion is controlled via the control unit only.
contact
The Start and Stop commands are controlled via digital
Control via contacts,
20 - signals. Fixed direction of rotation, clockwise rotation
clockwise rot. only
only.
Control via keypad, The start and stop commands are controlled via keypad.
23 -
clockwise rot. only Fixed direction of rotation, clockwise rotation only.
The Start and Stop commands are controlled from the
Control via cont. +KP,
24 - control unit or via digital signals. Fixed direction of rota-
clockwise rot. only
tion, clockwise rotation only.
Operation mode 20 to 24, anticlockwise direction of ro-
30 to 34
tation only.
Control via KP, The start and stop commands are controlled via digital
43 - direction of rot. via signals. The direction of rotation is controlled from the
contact + KP control unit or via digital signals.
Control via cont.+ KP, Both the Start and Stop commands as well as the sense
44 - direction of rot. via of rotation can be controlled from either the control unit
cont. + KP or via digital signals.
3-wire and control unit; control of direction of rotation
Ctrl. 3-Wire + KP, Dir.
46 - and signal
Cont. + KP
3-Wire Control 87 via contacts or control unit.

17.4 Brake Chopper and Brake Resistance
The frequency inverters feature a brake chopper transistor. The external brake resis-
tor is connected to terminals Rb1 and Rb2. The parameter Trigger Threshold 506
defines the switch-on threshold of the brake chopper. The generator output of the
drive, which leads to the increase in the DC link voltage, is converted to heat by the
external brake resistor above the limit set via parameter Trigger Threshold 506.
Parameter Settings
506 Trigger Threshold Udmin+25V 1000.0 V UdBC
Default settings of parameter Trigger Threshold 506:

- 385 V for ACT series of devices ACT 201
- 770 V for ACT series of devices ACT 401
The parameter Trigger Threshold 506 is to be set in such a way that it is between
the maximum DC link voltage which the mains can generate and the maximum admis-
sible DC link voltage of the frequency inverter.
U Netz ⋅1.1 ⋅ 2 < Ud BC < Ud max
If the parameter Trigger Threshold 506 is set larger than the maximum admissible
DC link voltage, the brake chopper cannot become active, the brake chopper is
switched off.
If the parameter Trigger Threshold 506 is set to a value below the DC link voltage
generated by the mains, error message F0705 (chapter "Error Messages") is displayed
if the start command is issued to the frequency inverter.
If the DC link voltage exceeds the maximum values of 400 V for the ACT 201 series of
devices and 800 V for the ACT 401 series of devices, respectively, error message
F0700 is displayed (chapter "Error Messages").
The sampling period of the function is 125 µs.

After exceeding the trigger threshold the brake chopper remains in switched-on condi-
tion for at least 125 µs, even if the DC link voltage will fall below the trigger threshold
in this time.
Ud
Trigger Threshold 506
Brake chopper
ON
OFF
t
125 µs

17.4.1 Dimensioning of Brake Resistor
The following values must be known for dimensioning:
− Peak braking power Pb Peak in W

− Resistance Rb in Ω
− Duty cycle DC in %
• Calculation of peak braking power Pb Peak
Pb Peak = Peak braking power in W

J = Moment of inertia of drive system kgm2
Pb Peak =
( 2
J ⋅ n1 − n 2
2
) n1 = Speed of drive system before the braking op-
eration in min-1
182 ⋅ t b n2 = Speed of drive system after the braking opera-
tion in min-1
tb = Braking time in s
• Calculation of resistance Rb
U d BC
2 Rb = Resistance in Ω
Rb = Ud BC = Switch-on threshold in V
Pb Peak Pb Peak = Peak braking power in W
The switch-on threshold Ud BC is the DC link voltage at which the brake resistor is
switched on. The switch-on threshold can be set, as described above, via parameter
Trigger Threshold 506.
Caution! The resistance of the brake resistor must not be less than the minimum
value Rb min -10%. The values for Rb min are listed in chapter "Technical
Data".
If the calculated resistance Rb of the brake resistor is between two standard series
values, the lower resistance is to be selected.
• Calculation of duty cycle DC
tb DC = Duty cycle
DC = tb = Braking time
t cycle
tcycle = Cycle time
Example:
tb = 48 s, tcycle = 120 s
tb t
DC = b = 0.4 = 40%
tcycle t cycle
In the case of infrequent short braking operations, typical values of the duty cycle DC
are at 10 %, for long braking operations (≥ 120 s) typical values are at 100%. In the
case of frequent deceleration and acceleration operations, it is recommended that the
duty cycle DC be calculated according to the above formula.
The calculated values for Pb Peak, Rb and DC can be used by the resistor manufacturers
for determining the resistor-specific permanent power.
Warning! The brake resistor is to be connected according to the specifications and

instructions in chapter "Connection of a Brake Resistor".
186 186 Operating

17.5 Motor Circuit Breaker
Motor circuit breakers are used for protecting a motor and its supply cable against
overheating by overload. Depending on the overload level, they disconnect the motor
from mains supply immediately in the case of a short-circuit or they disconnect the
motor if an overload has occurred for some time.
Conventional motor circuit breakers are
commercially available for various applica-
tions with different trigger characteristics (L,
G/U, R and K), as shown in the diagram on
the right. As frequency inverters in most
minutes
cases are used for supplying motors which
are classified as operating equipment with
very high starting currents, exclusively the K
characteristic was realized in this function.
Unlike the operation of a conventional motor
seconds
Protection switch which disconnects the
equipment to be protected immediately if
the trigger threshold is reached, this func-
tion provides the possibility of issuing a
warning instead of disconnecting the equip-
ment immediately.
1/1000 seconds
The rated current of the motor protection
switch refers to the rated motor current
stated via parameter Rated Current 371 of
the corresponding data set.
The rated values of the frequency inverter
are to be considered accordingly when it
comes to dimensioning the application.
x nominal current
The function of the motor circuit breaker can be linked to different data sets. In this
way, it is possible to operate different motors via one frequency inverter. Thus, each
motor can be equipped with its own motor protection switch.
In case a motor is operated via the frequency inverter for which some setting values,
e.g. minimum and maximum frequency, are changed via the data set switch-over,
only one motor circuit breaker may be installed. This functionality can be differenti-
ated by selecting the parameter Operation Mode 571 for single motor operation or
multiple motor operation.
0 - Off The function is deactivated
In each of the four data sets, the rated values are
K-Char.,Mul.Motor
1- monitored. Overloading the drive is prevented by the
Op.,Err.Sw.Off
fault switch-off "F0401".
K- The rated values in the first data set are used inde-
2 - Char.,Sing.Motor,Err.S pendently of the active data set. Overloading the drive
w.-Off is prevented by the fault switch-off "F0401".
In each of the four data sets, the rated values are
K-Char.,Multi-Motor
11 - monitored. Overloading the drive mechanism is sig-
Op.,Warning
naled by a warning message "A0200".
The rated values in the first data set are used inde-
K-Char.,Single-
22 - pendently of the active data set. Overloading the drive
Motor,Warning
mechanism is signaled by a warning message "A0200".

Multiple motor operation
Parameter Operation Mode 571 = 1 or 11
In multiple motor operation, it is assumed that for each data set a corresponding mo-
tor is used. For this, one motor and one motor protection switch are assigned to each
data set. In this operation mode, the rated values of the active data set are moni-
tored. The current output current of the frequency inverter is only taken into account
if the motor protection switch is activated by the data set. In the motor protection
switch of the other data sets, zero current is expected, with the result that the ther-
mal decay functions are taken into account. In combination with the data set change-
over, the function of the motor protection switches is similar to that of motors con-
nected alternately to the mains with their own protection switches.
Single motor operation

Parameter Operation Mode 571 = 2 or 22
In single motor operation, only one motor protection witch, which monitors the output
current of the frequency inverter, is active. In the case of a data set change-over,
only the switch-off limits derived from the rated machine parameters are changed
over. Accumulated thermal values are used after the change-over as well. In the case
of the data set change-over, please ensure that the machine data are stated identi-
cally for all data sets. In combination with the data set change-over, the function of
the motor protection switch is similar to that of motors connected alternately to the
mains with one common protection switch.
Motor protection, in particular self-ventilation motors, is improved via the Frequency
Limit 572 which can be set as a percentage of the rated frequency. The measured
output current in operating points below the frequency limit is assessed by a factor of
2 higher in the calculation of the trigger characteristic.
Parameter Settings
572 Frequency Limit 0% 300 % 0%
17.6 V-belt Monitoring

Continuous monitoring of the load behavior and thus of the connection between the
3-phase machine and the load is the task of the V-belt monitoring system. The pa-
rameter Operation Mode 581 defines the function behavior if the Active Current 214
(sensor-less control) or the torque-forming current component Isq 216 (field-oriented
control method) is below the set Trigger Limit Iactive 582 for longer than the pa-
rameterized Delay Time 583.

0 - Off The function is deactivated.
If the active current drops below the threshold value,
1 - Warning
the warning "A8000" is displayed.
The unloaded drive is switched off and fault message
2 - Error
"F0402" is displayed.
188 188 Operating

The error and warning messages can be read out by means of the digital outputs or
reported to an overriding control system. The Trigger Limit Iactive 582 is to be pa-
rameterized as a percentage of the Rated Current 371 for the application and the
possible operating points.
Parameter Settings
582 Trigger Limit Iactive 0.1% 100.0 % 10.0 %
583 Delay Time 0.1 s 600.0 s 10.0 s
17.7 Functions of Field-Orientated Control

The field-orientated control modes are based on a cascade control and the calculation
of a complex machine model. The various control functions can be supplemented by
special functions specific to the application.
17.7.1 Motor Chopper

The field-orientated control modes contain the function for adapted implementation of
the generator energy into heat in the connected three-phase machine. This enables
the realization of dynamic speed changes at minimum system costs. The torque and
speed behavior of the drive system is not influenced by the parameterized braking
behavior. The parameter Trigger Threshold 507 of the DC link voltage defines the
switch-on threshold of the motor chopper function.
Parameter Settings
507 Trigger Threshold Udmin+25V 1000.0 UdMC
The parameter Trigger Threshold 507 is to be set in such a way that it is between
the maximum DC link voltage which the mains can generate and the maximum admis-
sible DC link voltage of the frequency inverter.
U Mains ⋅1.1⋅ 2 < U dMC < Ud max

If the parameter Trigger Threshold 507 is set larger than the maximum admissible
DC link voltage, the motor chopper cannot become active, the motor chopper is
switched off.
If the set Trigger Threshold 507 is smaller than the maximum DC link voltage the
mains can generate, error message F0706 (chapter "Error Messages") is displayed
when the frequency inverter is switched on.

17.7.2 Temperature Adjustment
The field-orientated control modes are based on the most precise calculation of the
machine model possible. The rotor time constant is an important machine variable for
the calculation. The value to be read out via the parameter Act. Rotor Time Constant
227 is calculated from the inductivity of the rotor circuit and the rotor resistance. The
dependence of the rotor time constant on the motor temperature can be taken into
account in the case of particularly high precision requirements via a suitable meas-
urement. Via Operation Mode 465 for the temperature adjustment, you can select
different methods and actual value sources for temperature measurement.

Temperature synchronization
1 - Temp. Meas. on MFI1A (0 ... 200 °C => 0 ... 10 V / 0 ... 20 mA),
actual temperature value at multifunctional input 1.
Determination of temperature by frequency in-
4 - Temp. Meas. at Start verter via measurement of the winding resistance
without external temperature measurement.
Operation mode 1 requires an external temperature measurement system which
evaluates the temperature sensor and maps the temperature range from 0...200 °C to
an analog voltage or current signal. The Operation Mode 452 of multifunction input
MFI1 must be selected accordingly.
Operation mode 4 is available in configurations 210 and 230. When the signals Con-
troller release and Start clockwise or Start anticlockwise are present, the motor tem-
perature and the rotor time constant are synchronized by means of the measured
winding resistance.
The material used for the rotor winding of the motor is taken into account via the
parameter Temperature Coefficient 466. This value defines the change of the rotor
resistance as a function of the temperature for a certain material of the rotor winding.
Typical temperature coefficients are 39%/100 °C for copper and 36%/100 °C for alu-
minum at a temperature of 20°C.
The temperature characteristic within the software is calculated via the aforemen-
tioned temperature coefficient and the parameter Temperature Adjustment 467. The
adjustment temperature enables an additional optimization of the rotor time constant
alongside the parameter Rated Slip Correction Factor 718.
Parameter Settings
466 Temperature Coefficient 0.00%/100 °C 300.00%/100 °C 39.00%/100 °C
467 Adjusting Temperature -50 °C 300 °C 35 °C
The synchronization of the rotor time constant as a function of the winding tempera-
ture can be adjusted. The default values should normally be sufficiently precise so that
neither an adjustment of the rotor time constants via the parameter Rated Slip Cor-
rection Factor 718 nor an adjustment of the temperature synchronization via the
parameter Temperature Coefficient 466 is necessary. If an adjustment is necessary,
please remember that the rotor time constant is calculated by the guided commission-
ing via the machine data. The Adjusting Temperature 467 is to be set to the tempera-
ture at which the optimization of the extended machine data was carried out. The
temperature can be read out via the actual value parameter Winding Temperature
226 and can be used in the optimization for the parameter.
190 190 Operating

17.7.3 Encoder Monitoring
Failures of the speed sensor lead to a faulty behavior of the drive, as the measured
speed forms the foundation of the control mode. By default, the speed sensor moni-
toring system continuously monitors the speed sensor signal, the track signal and the
division marks. If, while the frequency inverter is released, a faulty signal is recog-
nized for longer than the timeout, a fault switch-off is effected. If the parameter Op-
eration Mode 760 is set to zero, the monitoring function is deactivated.

A fault message is displayed according to the timeouts
2 - Error
set.
The speed sensor monitoring is to be parameterized in the sub functions according to

the application. The monitoring function becomes active with the release of the fre-
quency inverter and the start command. The timeout defines a monitoring time in
which the condition for the fault switch-off must be fulfilled without interruption. If
one of the timeouts is set to zero, this monitoring function is deactivated.
Parameter Settings
761 Timeout: Signal Fault 0 ms 65000 ms 1000 ms
762 Timeout: Channel fault 0 ms 65000 ms 1000 ms
763 Timeout: Direction fault 0 ms 65000 ms 1000 ms
Timeout: Signal Fault

The actual speed measured is compared with the output value of the speed controller.
If the actual speed value is exactly zero for the time selected with the parameter
Timeout: Signal fault 761, although a reference value is available, the fault is dis-
played with the message "F1430".
Timeout: Channel fault

The actual speed measurement monitors the sequence in time of the signals in the
quadruple evaluation of the speed sensor operation mode. If the speed sensor signal
is faulty for the time selected with the parameter Timeout: Channel fault 762, the
fault is displayed with the message "F1431".
Timeout: Direction fault

The actual speed measured is compared with the reference speed. If the sign be-
tween reference value and actual value differs for the time selected with the parame-
ter Timeout: Direction fault 763, the fault is displayed with the message "F1432".
The monitoring function is reset when the drive mechanism has moved in the refer-
ence value direction by a quarter of a revolution.

18 Actual Values
The various control functions and methods include electrical control variables and
various calculated actual values of the machine or system. The different actual values
can be read out for operational and error diagnosis via a communication interface or
in the VAL menu branch of the operating unit.
18.1 Actual Values of the Frequency Inverter

The modular hardware of the frequency inverter enables application-specific adapta-
tion. Further actual value parameters can be displayed as a function of the selected
configuration and the installed expansion cards.
Actual Values of the Frequency Inverter

No. Description Function
222 DC link voltage Direct voltage in the DC link.
Output voltage of the frequency inverter relative
223 Modulation
to the mains voltage (100% = UFIN).
Sum of the Reference Frequency Sources 475 as
Internal Reference Fre-
228 a reference value from the frequency reference
quency
value channel.
Sum of the Reference Percentage Sources 476
229 Reference Percentage Value as a reference value from the reference percent-
age channel.
Actual value signal on the Actual Percentage
230 Actual Percentage Value
Source 478.
Operating hours in which the output stage of the
244 Working Hours Counter
inverter is active.
Operating hours of the frequency inverter in
245 Operation Hours Counter
which supply voltage is available.
The data set actively in use according to Data
249 Active data set Set Change-Over 1 70 and Data Set Change-
Over 2 71.
Decimally coded status of the six digital inputs
250 Digital Inputs and of multifunctional input 1 in Operation Mode
452 - digital input.
Input signal on multifunctional input 1 in Opera-
251 Analog Input MFI1A
tion Mode 452 - analog input.
Signal on repetition frequency input according to
252 Repetition frequency input
Operation Mode 496.
Decimally coded status of the two digital outputs
254 Digital Outputs and of multifunctional output 1 in Operation
Mode 550 – digital.
255 Heat Sink Temperature Measured heat sink temperature.
256 Inside Temperature Measured inside temperature.
Output signal on multifunctional output 1 in Op-
257 Analog Output MFO1A
eration Mode 550 – analog.
259 Current Error Error message with error code and abbreviation.
Warning message with error code and abbrevia-
269 Warnings
tion.
The reference value signal is limited by the con-
275 Controller Status
troller coded in the controller status.
Repetition frequency output Output signal on multifunctional input 1 in Op-
278
MFO1F eration Mode 550 – repetition frequency.
Note: The actual values can be read out and monitored in the VAL menu
branch of the operating unit. The parameter Control Level 28 in the
PARA menu branch defines the selection of the actual value parameters.

18.2 Actual Values of the Machine
The frequency inverter controls the behavior of the machine in the various operating
points. As a function of the configuration selected and the expansion cards installed,
control variables and further actual value parameters of the machine can be dis-
played.
Actual Values of the Machine

The output frequency (motor frequency) of the
210 Stator Frequency
frequency inverter.
Calculated effective output current (motor cur-
211 R.m.s Current
rent) of the frequency inverter.
Calculated R.m.s. figure of the phase-to-phase
212 Output Voltage
voltage (motor voltage) of the frequency inverter
Active power calculated from the voltage, the
213 Active Power
current and the control variables.
Active current calculated from the rated motor
214 Active Current
parameters, the control variables and the current
Current component of the field-orientated control
215 Isd
forming the magnetic flux.
Torque-forming current component of field-
216 Isq
orientated control.
Calculated from the data on encoder 1, the No.
217 Encoder 1 Frequency
of Pole Pairs 373 and the encoder signal.
218 Encoder 1 Speed Calculation from encoder 1 frequency.
Difference from the synchronous frequency cal-
221 Slip Frequency culated from the rated motor parameters, the
control variables and the current.
Torque at the current output frequency calcu-
224 Torque lated from the voltage, the current and the con-
trol variables.
Current magnetic flux relative to the rated motor
225 Rotor Flux
parameters.
Measured temperature of the motor winding
226 Winding Temperature according to Operation Mode 465 for tempera-
ture adjustment.
Time constant calculated for the operating point
227 Act. Rotor Time Constant of the machine from the rated motor parame-
ters, the rated and control variables.
Voltage component of the field-orientated control
235 Flux-Forming Voltage
forming the magnetic flux.
Voltage component of the field-orientated control
236 Torque-Forming Voltage
forming the torque.
Magnetic flux calculated according to the rated
238 Flux Value
values and the operating point of the motor.
Reactive current calculated from the rated motor
239 Reactive Current
parameters, the control variables and the current
240 Actual Speed Measured and/or calculated speed of drive.
241 Actual Frequency Measured and/or calculated frequency of drive.
PARA menu branch defines the selection of the actual value parameters
to be selected.

18.3 Actual Value Memory
The assessment of the operating behavior and the maintenance of the frequency in-
verter in the application is facilitated by storing various actual values. The actual value
memory guarantees monitoring of the individual variables for a definable period. The
parameters of the actual value memory can be read out via a communication interface
and displayed via the operating unit. In addition, the operating unit provides monitor-
ing of the peak and mean values in the VAL menu branch.
Actual value memory

Utilization of the device-dependent overload of
231 Peak Value Long Term Ixt
60 seconds.
Utilization of the device-dependent overload of 1
232 Peak Value, Short Term Ixt
second.
287 Peak Value Vdc The maximum DC link voltage measured.
The average DC link voltage calculated in the
288 Average Value Vdc
period of observation.
The highest measured heat sink temperature of
289 Peak Value Heat Sink Temp.
the frequency inverter.
Average Value Heat Sink The average heat sink temperature calculated in
290
Temp. the period of observation.
Peak Value Inside Tempera- The maximum measured inside temperature in
291
ture the frequency inverter.
Average Value Inside Tem- The average inside temperature calculated in the
292
perature period of observation.
The highest absolute current calculated from the
293 Peak value Irms
measured motor phases.
The average absolute current calculated in the
294 Average value Irms
period of observation.
Peak Value Active Power The largest calculated active power in motor
295
pos. operation.
Maximum generator active power calculated
Peak Value Active Power
296 from the voltage, the current and the control
neg.
variables.
The average active power calculated in the pe-
297 Average Value Active Power
riod of observation.
The calculated energy to the motor in motor
301 Energy, positive
operation.
The calculated energy from the motor in genera-
302 Energy, negative
tor operation.
PARA menu branch defines the selection of the actual value parameters
to be selected.
194 194 Operating

The Reset Memory 237 parameter to be selected in the PARA menu branch of the
operating unit enables purposeful resetting of the individual average and peak values.
The peak value and the average value with the values stored in the period are over-
written with the parameter value zero.

0 - No deleting Values of actual value memory remain unchanged.
Peak Value Long Term
1- Reset Peak Value Long-Term Ixt 231.
Ixt
Peak Value Short Term
2- Reset Peak Value Short-Term Ixt 232.
Ixt
3 - Peak Value Vdc Reset Peak Value Vdc 287.
4 - Average Value Vdc Delete Average Value Vdc. 288.
5 - Peak Value Tc Reset Peak Value Heat Sink Temp. 289.
6 - Average Value Tc Delete Average Value Heat Sink Temp. 290.
7 - Peak Value Ti Reset Peak Value Inside Temperature 291.
8 - Average Value Ti Delete Average Value Inside Temperature 292.
9 - Peak value Irms Reset Peak Value Irms 293.
10 - Average value Irms Delete Average Value Irms 294.
11 - Peak Value Pactive pos. Reset Peak Value Active Power pos. 295.
12 - Peak Value Pactive neg. Reset Peak Value Active Power neg. 296.
13 - Average Value Pactive Delete Average Value Active Power 297.
16 - Energy, positive Reset parameter Energy, positive 301.
17 - Energy, negative Reset parameter Energy, negative 302.
100 - All Peak Values Reset all peak values stored.
101 - All Average Values Delete average values and stored values.
102 - All Values Delete the entire actual value memory.
18.4 Actual Values of the System

The calculation of the actual values of the system is based on the parameterized sys-
tem data. Specific to the application, the parameters are calculated from the factors,
electrical variables and the controls. The correct display of the actual values is a func-
tion of the data of the system to be parameterized.
18.4.1 Actual Value System

The drive can be monitored via the actual value Actual Value System 242.
The Actual Frequency 241 to be monitored is multiplied by the Factor Actual Value
System 389 and can be read out via the parameter Actual Value System 242, i.e.
Actual Frequency 241 x Factor Actual Value System 389 = Actual Value System
242.
Actual Value System

242 Actual Value System Calculated frequency of drive

18.4.2 Volume Flow and Pressure
The parameterization of the factors Nominal Volumetric Flow 397 and Nominal
Pressure 398 is necessary if the matching actual values Volumetric flow 285 and
Pressure 286 are used to monitor the drive. The conversion is done using the electri-
cal control parameters. Volume Flow 285 and Pressure 286 are referred to the Ef-
fective Current 214 in the case of the sensor-less control methods. In the case of the
field-oriented control methods, they are referred to the torque-forming current com-
ponent Isq 216.
Volume Flow and Pressure

285 Volumetric Flow Calculated volume flow with the unit m3/h
Pressure calculated according to the characteris-
286 Pressure
tic with the unit kPa
196 196 Operating

19 Error Protocol
The various control methods and the hardware of the frequency inverter include func-
tions which continuously monitor the application. The operational and error diagnosis
is facilitated by the information stored in the error protocol.
19.1 Error List

The last 16 fault messages are stored in chronological order and the No. of Errors
362 shows the number of errors which have occurred since commissioning of the
frequency inverter. In the VAL menu branch of the control unit, the error code FXXXX
is displayed. The meaning of the error key is described in the following chapter "Error
Messages". Via the PC program, the number of operation hours (h), operation minutes
(m) and the fault message can additionally be read out. The current operating hours
can be read out via the Operation Hours Counter 245. The fault report can be ac-
knowledged via the keys of the operating unit and according to the assignment Error
Acknowledgment 103.
Error List
310 Last Error hhhhh:mm ; FXXXX fault message.
311 Last Error but one hhhhh:mm ; FXXXX fault message.
312 to 325 Eerror 3 to error 16.
Number of errors occurred after commissioning
362 No. of errors occurred
of the frequency inverter.
The error and warning behavior of the frequency inverter can be set in various ways.
The automatic error acknowledgment enables acknowledgment of the faults Overcur-
rent F0500, Overcurrent F0507 and Overvoltage F0700 without intervention by an
overriding control system or the user. The No. of self acknowledged Errors 363
shows the total number of automatic error acknowledgments.
Error List
363 No. of acknowledgment Errors Total number of automatic error acknowledg-
ment with synchronization.
19.1.1 Error Messages

The error code stored following a fault comprises the error group FXX and the follow-
ing code number XX.
Error Messages
Code Meaning
F00 00 No fault has occurred.
Overload
F01 00 Frequency inverter overloaded.
02 Frequency inverter overloaded (60 s), check load behavior.
F01
03 Short-term overload (1 s), check motor and application parameters.
Heat Sink
00 Heat sink temperature too high, check cooling and fan.
F02
01 Temperature sensor defective or ambient temperature too low.
Table "Error Messages" continued on next page.

Inside
Code Meaning
00 Inside temperature too high, check cooling and fan.
F03
01 Inside temperature too low, check electrical cabinet heating.
Motor Connection
Motor temperature too high or sensor defective, check connection
00
S6IND.
F04 01 Motor circuit breaker tripped, check drive.
02 V-belt monitoring reports no load on the drive.
03 Phase failure, check motor and wiring.
Output current
00 Overloaded, check load situation and ramps.
03 Short circuit or earth fault, check motor and wiring.
04 Overloaded, check load situation and current value limit controller.
F05
05 Asymmetric motor current, check current and wiring.
06 Motor phase current too high, check motor and wiring.
07 Message from phase monitoring, check motor and wiring.
DC link voltage
DC link voltage too high, check deceleration ramps and connected brake
00
resistor.
01 DC link voltage too low, check mains voltage.
02 Power failure, check mains voltage and circuit.
F07
03 Phase failure, check mains fuses and circuit.
04 Reference DC-Link Limitation 680 too low, check mains voltage.
05 Brake chopper Trigger Threshold 506 too low, check mains voltage.
06 Motor chopper Trigger Threshold 507 too low, check mains voltage.
Electronics voltage
01 Electronics voltage 24 V too low, check control terminal.
F08
04 Electronics voltage too high, check wiring of control terminals.
Output frequency
00 Output frequency too high, check control signals and settings.
F11 Max. frequency reached by control, check deceleration ramps and con-
01
nected brake resistor.
Motor Connection
00 Earth fault on output, check motor and wiring.
Set IDC-Compensation Limit 415 reached, check motor and cabling,
F13 01
increase limit, if necessary.
10 Minimum current monitoring, check motor and wiring.
Control Connection
01 Reference value on multifunctional input 1 faulty, check signal.
07 Overcurrent on multifunctional input 1, check signal.
F14 30 Speed sensor signal defective, check connections S4IND and S5IND.
31 One track of the speed sensor signal is missing, check connections.
32 Direction of rotation of speed sensor wrong, check connections.
Optional Components
Data transmission from control unit KP 500 to inverter failed. In the
F0A 10
control unit must be stored at least 1 file.
The communication module was fitted to slot B without disconnection of
F0B 13
the mains voltage, switch mains voltage off.
In addition to fault messages mentioned, there are further fault messages. However
these messages are only used for internal purposes and are not listed here. If you
receive fault messages which are not listed here, please contact us by phone.

19.2 Error Environment
The parameters of the error environment help troubleshooting both in the settings of
the frequency inverter and also in the complete application. The error environment
documents the operational behavior of the frequency inverter at the time of the last
four faults.
Error Environment
330 DC link voltage Direct voltage in the DC link.
Calculated output voltage (motor voltage) of the
331 output voltage
frequency inverter.
The output frequency (motor frequency) of the
332 Stator Frequency
frequency inverter.
Calculated from the data on encoder 1, the No.
333 Encoder 1 Frequency
of Pole Pairs 373 and the encoder signal.
335 Phase Current Ia Measured current in motor phase U.
336 Phase Current Ib Measured current in motor phase V.
337 Phase Current Ic Measured current in motor phase W.
Calculated effective output current (motor cur-
338 R.m.s Current
rent) of the frequency inverter.
Current component forming the magnetic flux or
339 Isd / Reactive Current
the calculated reactive current.
Current component forming the torque or the
340 Isq / Active Current
calculated active current.
Magnetizing current relative to the rated motor
341 Rotor Magnetizing Current
parameters and the operating point.
Torque calculated from the voltage, the current
342 Torque
and the control variables.
Input signal on multifunctional input 1 in Opera-
343 Analog Input MFI1A
tion Mode 452 - analog input.
Output signal on multifunctional output 1 in Op-
346 Analog Output MFO1A
eration Mode 550 – analog.
Signal at repetition frequency output according
349 Repetition Frequency Output
to Operation Mode 550 – repetition frequency.
Decimally coded status of the six digital inputs
350 Status of Digital Inputs and of multifunctional input 1 in Operation Mode
452 - digital input.
Decimally coded status of the two digital outputs
351 Status of Digital Outputs and of multifunctional output 1 in Operation
Mode 550 – digital.
The time of the error in hours (h), minutes (m)
352 Time since Release and seconds (s) after the release signal:
hhhhh:mm:ss . sec/10 sec/100 sec/1000.
353 Heat Sink Temperature Measured heat sink temperature.
354 Inside Temperature Measured inside temperature.
The reference value signal is limited by the con-
355 Controller Status
troller coded in the controller status.
356 Warning Status The warning messages coded in warning status.
Table "Error Environment" continued on next page.

Error Environment
357 Int. Value 1 Software service parameter.
358 Int. Value 2 Software service parameter.
359 Long Value 1 Software service parameter.
360 Long Value 2 Software service parameter.
The Checksum 361 parameter shows whether the storage of the error environment
was free of errors (OK) or incomplete (NOK).
Error Environment
361 Checksum Check protocol of the error environment.

20 Operational and Error Diagnosis
Operation of the frequency inverter and the connected load are monitored continu-
ously. Various functions document the operational behavior and facilitate the opera-
tional and error diagnosis.
20.1 Status Display

The green and red light-emitting diodes give information about the operating point of
the frequency inverter. If the control unit is connected, the status messages are addi-
tionally displayed by the display elements RUN, WARN and FAULT.
Status Display
green LED red LED Display Description
off off - No supply voltage.
on on - Initialization and self-test.
flashes off RUN flashes Ready for operation, no output signal.
on off RUN Operating message.
RUN flashes +
on flashes Operational message, current Warning 269.
WARN flashes
RUN flashes +
flashes flashes Ready for operation, current Warning 269.
WARN flashes
off flashes FAULT flashes Last Error 310 of frequency inverter.
off on FAULT Last Error 310, acknowledge fault.
20.2 Status of Digital Signals

The status display of the digital input and output signals enables checking of the vari-
ous control signals and their assignment to the corresponding software functions, in
particular during commissioning.
Coding of the status of the digital signals
Assignment: Bit
7 6 5 4 3 2 1 0
Control signal 8
Control signal 7
Control signal 6
Control signal 5
Control signal 4
Control signal 3
Control signal 2
Control signal 1

A decimal value is displayed, indicating the status of the digital signals in bits after
conversion into a binary figure.
Example: Decimal figure 33 is displayed. Converted into the binary system, the
number reads OOIOOOOI. Thus, the following contact inputs or out-
puts are active:
− Control signal at digital input or output 1
− Control signal at digital input or output 6
20.3 Controller Status

The controller status can be used to establish which of the control functions are ac-
tive. If several controllers are active at the time, a controller code composed of the
sum total of the individual codes is displayed. The display of the controller status by
the control unit and the light-emitting diodes can be parameterized via the Controller
-Status Message 409.
Coding of the controller status
CXXXX ABCDE
⏐ ⏐
Controller code Controller abbreviation
Code Controller Status
C 00 00 - No controller active
Voltage controller is in the rise phase according to Operation
C 00 01 UDdyn
Mode 670.
The output frequency in the case of a mains failure is below
C 00 02 UDstop
the Shutdown Threshold 675.
Failure of the mains voltage and power regulation active ac-
C 00 04 UDctr
cording to Operation Mode 670 of the voltage controller.
The DC link voltage has exceeded the Reference DC-Link
C 00 08 UDlim
Limitation 680.
The Dyn. Voltage Pre-Control 605 accelerates the control
C 00 10 Boost
behavior.
The output current is limited by the current limit value control-
C 00 20 Ilim
ler or the speed controller.
The output power or the torque are limited on the speed con-
C 00 40 Tlim
troller.
Switch-over of field-orientated control between speed and
C 00 80 Tctr
torque-controlled control method.
The Operation Mode 620 selected in starting behavior limits
C 01 00 Rstp
the output current.
Overload limit of the long-term Ixt (60s) reached, intelligent
C 02 00 IxtLtLim
current limits active.
Overload limit of the short-term Ixt (1s) reached, intelligent
C 04 00 IxtStLim
current limits active.
Max. heat sink temperature TK reached, intelligent current
C 08 00 Tclim
limits of Operation Mode 573 active.
Max. motor temperature reached, intelligent current limits of
C 10 00 PTClim
Operation Mode 573 active.
The reference frequency has reached the Maximum Fre-
C 20 00 Flim
quency 419. The frequency limitation is active.
Example: The controller status is displayed

C0024 UDctr Ilim
The controller status results from the hexadecimal sum of the controller
codes (0004+0020 = 0024).
At the same, the power failure regulation and also the current limitation
of the speed controller are active.

20.4 Warning Status
The current warning is displayed by a message in the warning status and can be used
for an early message of a critical operational condition. The combination of different
warnings can be set in parameter Create Warning Mask 536. If a warning is present,
it is displayed by the flashing red LED and WARN is displayed on the control unit. If
several warnings are present, the warning status is displayed as the sum of the indi-
vidual warning codes.
Coding of the warning status
AXXXX ABCDE
⏐ ⏐
Warning code Abbreviation for the warning
Code Warning Status

A 00 00 - No warning message present.
A 00 01 Ixt Frequency inverter overloaded (A0002 or A0004).
Overload for 60 s relative to the nominal output of the fre-
A 00 02 IxtSt
quency inverter.
Short-time overload for 1 s relative to the nominal output of the
A 00 04 IxtLt
frequency inverter.
Max. heat sink temperature TK of 80 °C less the Warning Limit
A 00 08 Tc
Heat Sink Temp 407 reached.
Max. inside temperature Ti of 65 °C less the Warning Limit In-
A 00 10 Ti
side Temp. 408 reached.
The controller stated in Controller Status 275 limits the refer-
A 00 20 Lim
ence value.
A 00 40 INIT Frequency inverter is initialized.
Warning behavior according to parameterized Motor Temp. Op-
A 00 80 PTC
eration Mode 570 at max. motor temperature TMotor.
A 01 00 Mains Phase Supervision 576 reports a phase failure.
Motor circuit breaker parameterized in Operation Mode 571
A 02 00 PMS
tripped.
The Maximum Frequency 419 was exceeded. The frequency
A 04 00 Flim
limitation is active.
The input signal MFI1A is lower than 1 V / 2 mA according to
A 08 00 A1
the operation mode for the Error/Warning Behavior 453.
The input signal is lower than 1 V / 2 mA according to the op-
A 10 00 A2
eration mode for the Error/Warning Behavior 453.
A Slave at the system bus signals a fault;
A 20 00 SYS
Warning is only relevant with option EM-SYS.
The DC link voltage has reached the type-dependent minimum
A 40 00 UDC
value.
The Operation Mode 581 for V-belt monitoring signals no-load
A 80 00 BELT
operation of the application.
Example: The warning status is displayed.
A008D Ixt IxtLt Tc PTC
The warning status results from the hexadecimal sum of the warning
codes (0001+0004+0008+0080 = 008D).
The short-term overload (1 s), warning limit heat sink temperature and
warning limit motor temperature warnings are present.

21 Parameter List
The parameter list is structured according to the menu branches of the control unit.
The parameters are listed in ascending numerical order.. A headline (shaded) can
appear several times, i.e. a subject area may be listed at different places in the table.
For better clarity, the parameters have been marked with pictograms:
The parameter is available in the four data sets.

The parameter value is set by the SETUP routine.
This parameter cannot be written when the frequency inverter is in operation.
IFIN, UFIN, PFIN: rated values of the frequency inverter, o: overload capacity of frequency inverter
21.1 Actual Value Menu (VAL)

No. Description Unit Display range Chapter
210 Stator Frequency Hz 0.00 ... 999.99 18.2
211 R.m.s Current A 0.0 ... Imax 18.2
212 Output Voltage V 0.0 ... UFIN 18.2
213 Active Power kW 0.0 ... Pmax 18.2
214 Active Current A 0.0 ... Imax 18.2
215 Isd A 0.0 ... Imax 18.2
216 Isq A 0.0 ... Imax 18.2
217 Encoder 1 Frequency Hz 0.00 ... 999.99 9.4
218 Encoder 1 Speed 1/min 0 ... 60000 9.4
221 Slip Frequency Hz 0.0 ... 999.99 18.2
222 DC link voltage V 0.0 ... Udmax-25 18.1
223 Modulation % 0 ... 100 18.1
224 Torque Nm ± 9999.9 18.2
225 Rotor Flux % 0 ... 100 18.2
226 Winding Temperature deg.C 0 ... 999 17.7.2
227 Act. Rotor Time Constant ms 0 ... τmax 18.2
228 Internal Reference Frequency Hz 0.00 ... fmax 18.1
229 Reference Percentage Value % ± 300.00 18.1
230 Actual Percentage Value % ± 300.00 18.1
Actual value memory
231 Peak Value Long Term Ixt % 0.00 ... 100.00 18.3
232 Peak Value Short Term Ixt % 0.00 ... 100.00 18.3
235 Flux-Forming Voltage V 0.0 ... UFIN 18.2
236 Torque-Forming Voltage V 0.0 ... UFIN 18.2
238 Flux Value % 0.0 ... 100.0 18.2
239 Reactive Current A 0.0 ... Imax 18.2
240 Actual Speed 1/min 0 ... 60000 18.2
241 Actual Frequency Hz 0.0 ... 999.99 18.2
Actual Values of the System
242 Actual Value System Hz 0.0 ... 999.99 18.4.1

244 Working Hours Counter h 99999 18.1
245 Operation Hours Counter h 99999 18.1
249 Active Data Set - 1 ... 4 14.4.7
250 Digital Inputs - 00 ... 255 20.2
251 Analog Input MFI1A % ± 100.00 14.1.1
252 Repetition frequency input Hz 0.0 ... 999.99 13.11
254 Digital Outputs - 00 ... 255 20.2
255 Heat Sink Temperature deg.C 0 ... Tkmax 18.1
256 Inside Temperature deg.C 0 ... Timax 18.1
257 Analog Output MFO1A V 0.0 ... 24.0 14.2.1
259 Current Error - FXXXX 18.1
269 Warnings - AXXXX 18.1
275 Controller Status - CXXXX 18.1
278 Frequency MFO1F Hz 0.00 ... fmax 14.2.2
Actual Values of the System
285 Volumetric Flow m3/h 0 ... 99999 18.4.2
286 Pressure kPa 0.0 ... 999.9 18.4.2
Actual value memory
287 Peak Value Vdc V 0.0 ... Udmax 18.3
288 Average Value Vdc V 0.0 ... Udmax 18.3
289 Peak Value Heat Sink Temp. deg.C 0 ... Tkmax 18.3
290 Average Value Heat Sink Temp. deg.C 0 ... Tkmax 18.3
291 Peak Value Inside Temperature deg.C 0 ... Timax 18.3
292 Average Value Inside Temperature deg.C 0 ... Timax 18.3
293 Peak value Irms A 0.0 ... o ⋅ IFIN 18.3
294 Average value Irms A 0.0 ... o ⋅ IFIN 18.3
295 Peak Value Active Power pos. kW 0.0 ... o⋅PFIN 18.3
296 Peak Value Active Power neg. kW 0.0 ... o⋅PFIN 18.3
297 Average Value Active Power kW 0.0 ... o⋅PFIN 18.3
301 Energy, positive kWh 0 ... 99999 18.3
302 Energy, negative kWh 0 ... 99999 18.3
Error List
310 Last Error h:m; F 00000:00; FXXXX 19.1
311 Last Error but one h:m; F 00000:00; FXXXX 19.1
312 Error 3 h:m; F 00000:00; FXXXX 19.1
313 Error 4 h:m; F 00000:00; FXXXX 19.1
314 Error 5 h:m; F 00000:00; FXXXX 19.1
315 Error 6 h:m; F 00000:00; FXXXX 19.1
316 Error 7 h:m; F 00000:00; FXXXX 19.1
317 Error 8 h:m; F 00000:00; FXXXX 19.1
318 Error 9 h:m; F 00000:00; FXXXX 19.1
319 Error 10 h:m; F 00000:00; FXXXX 19.1
320 Error 11 h:m; F 00000:00; FXXXX 19.1
321 Error 12 h:m; F 00000:00; FXXXX 19.1
322 Error 13 h:m; F 00000:00; FXXXX 19.1
323 Error 14 h:m; F 00000:00; FXXXX 19.1
324 Error 15 h:m; F 00000:00; FXXXX 19.1
325 Error 16 h:m; F 00000:00; FXXXX 19.1

Error Environment
330 DC link voltage V 0.0 ... Udmax 19.2
331 output voltage V 0.0 ... UFIN 19.2
332 Stator Frequency Hz 0.00 ... 999.99 19.2
333 Encoder 1 Frequency Hz 0.00 ... 999.99 19.2
335 Phase Current Ia A 0.0 ... Imax 19.2
336 Phase Current Ib A 0.0 ... Imax 19.2
337 Phase Current Ic A 0.0 ... Imax 19.2
338 R.m.s Current A 0.0 ... Imax 19.2
339 Isd / Reactive Current A 0.0 ... Imax 19.2
340 Isq / Active Current A 0.0 ... Imax 19.2
341 Rotor Magnetizing Current A 0.0 ... Imax 19.2
342 Torque Nm ± 9999.9 19.2
343 Analog Input MFI1A % ± 100.00 19.2
346 Analog Output MFO1A V 0.0 ... 24.0 19.2
349 Repetition Frequency Output Hz 0.00 ... 999.99 19.2
350 Status of Digital Inputs - 00 ... 255 20.2
351 Status of Digital Outputs - 00 ... 255 20.2
352 Time since Release h:m:s.ms 00000:00:00.000 19.2
353 Heat Sink Temperature deg.C 0 ... Tkmax 19.2
354 Inside Temperature deg.C 0 ... Timax 19.2
355 Controller Status - C0000 ... CFFFF 20.3
356 Warning Status - A0000 ... AFFFF 20.4
357 Int Value 1 - ± 32768 19.2
358 Int Value 2 - ± 32768 19.2
359 Long Value 1 - ± 2147483647 19.2
360 Long Value 2 - ± 2147483647 19.2
361 Checksum - OK / NOK 19.2
Error List
362 No. of Errors - 0 ... 32767 19.1
363 No. of self acknowledged Errors - 0 ... 32767 19.1
Positioning
470 Rotations U 0.000 ... 1⋅106 11.6
Digital Outputs
537 Actual Warning Mask - AXXXXXXXX 14.3.7
Self-configuration
797 SETUP Status - OK / NOK 7.5

21.2 Parameter Menu (PARA)
Inverter Data
No. Description Unit Setting range Chapter
0 Serial Number - Characters 8.1
1 Optional Modules - Characters 8.2
12 Inverter Software Version - Characters 8.3
27 Set Password - 0 ... 999 8.4
28 Control Level - 1 ... 3 8.5
29 User Name - 32 characters 8.6
30 Configuration - Selection 8.7
33 Language - Selection 8.8
34 Program(ming) - 0 ... 9999 8.9
37 Start Positioning of Axle - Selection 11.6.2
Fan
39 Switch-On Temperature deg.C 0 ... 60 17.2
Digital Inputs
62 Frequency Motorpoti Up - Selection 14.4.9
63 Frequency Motorpot. Down - Selection 14.4.9
66 Fixed Frequency Change-Over 1 - Selection 14.4.8
67 Fixed Frequency Change-Over 2 - Selection 14.4.8
68 Start Clockwise - Selection 14.4.1
69 Start Anticlockwise - Selection 14.4.1
70 Data set change-over 1 - Selection 14.4.7
71 Data set change-over 2 - Selection 14.4.7
72 Percent Motorpoti Up - Selection 14.4.9
73 Percent Motorpoti Down - Selection 14.4.9
75 Fixed percentage value change-over 1 - Selection 14.4.8
76 Fixed percentage value change-over 2 - Selection 14.4.8
83 Timer 1 - Selection 14.4.4
84 Timer 2 - Selection 14.4.4
87 Start 3-wire-control - Selection 14.4.2
103 Error Acknowledgment - Selection 14.4.3
164 n-/M-Control Change-Over - Selection 14.4.6
Logic Modules
198 Operation mode Logic 1 - Selection 14.5.3
199 Input 1 Logic 1 - Selection 14.5.3
Digital Inputs
204 Therm. Contact - Selection 14.4.5
Logic Modules
Actual value memory
237 Reset Memory - Selection 18.3

Controlled commissioning
369 Motor Type - Selection 7.2.3
Rated Motor Parameters
370 Rated Voltage V 0.17⋅UFIN ... 2⋅UFIN 9.1
371 Rated Current A 0.01⋅IFIN ... 10⋅o ⋅ IFIN 9.1
372 Rated Speed U/min 96 ... 60000 9.1
373 No. of Pole Pairs - 1 ... 24 9.1
374 Rated Cosinus Phi - 0.01 ... 1.00 9.1
375 Rated Frequency Hz 10.00 ... 1000.00 9.1
376 Rated Mech. Power kW 0.1⋅PFIN ... 10⋅PFIN 9.1
Further motor parameters
377 Stator Resistance mOhm 0 ... 65535 9.2
378 Leakage Coeff. % 1.0 ... 20.0 9.2
System data
389 Factor Actual Value System - -100.000 ... 100.000 10.1
397 Nominal Volumetric Flow m3/h 1 ... 99999 10.2
398 Nominal Pressure kPa 0.1 ... 999.9 10.2
Pulse Width Modulation
400 Switching frequency - Selection 17.1
401 Min. Switching Frequency - Selection 17.1
Error/warning behavior
405 Warning Limit Short Term Ixt % 6 ... 100 12.1
406 Warning Limit Long Term Ixt % 6 ... 100 12.1
407 Warning Limit Heat Sink Temp. deg.C -25 ... 0 12.2
408 Warning Limit Inside Temp. deg.C -25 ... 0 12.2
409 Controller-Status Message - Selection 12.3
Bus controller
412 Local/Remote - Selection 17.3
415 IDC Compensation Limit V 0.0 ... 1.5 12.4
417 Frequency Switch-Off Limit Hz 0.00 ... 999.99 12.5
Frequency Limits
418 Minimum Frequency Hz 0.00 ... 999.99 13.1
419 Maximum Frequency Hz 0.00 ... 999.99 13.1
Frequency ramps
420 Acceleration (Clockwise) Hz/s 0.00 ... 9999.99 13.7
421 Deceleration (Clockwise) Hz/s 0.01 ... 9999.99 13.7
422 Acceleration Anticlockwise Hz/s -0.01 ... 9999.99 13.7
423 Deceleration Anticlockwise Hz/s -0.01 ... 9999.99 13.7
424 Emergency Stop Clockwise Hz/s 0.01 ... 9999.99 13.7
425 Emergency Stop Anticlockwise Hz/s 0.01 ... 9999.99 13.7
426 Maximum Leading Hz 0.01 ... 999.99 13.7
430 Ramp Rise Time Clockwise ms 0 ... 65000 13.7
431 Ramp Fall Time Clockwise ms 0 ... 65000 13.7
432 Ramp Rise Time Anticlockwise ms 0 ... 65000 13.7
433 Ramp Rise Time Anticlockwise ms 0 ... 65000 13.7

440 Operation mode - Selection 16.3
441 Fixed Frequency Hz -999.99 ... 999.99 16.3
442 max. P-Component Hz 0.01 ... 999.99 16.3
443 Hysteresis % 0.01 ... 100.00 16.3
444 Amplification - -15.00 ... 15.00 16.3
445 Integral Time ms 0 ... 32767 16.3
446 Ind. Volume Flow Control Factor - 0.10 ... 2.00 16.3
Block Frequencies
447 1st Blocking Frequency Hz 0.00 ... 999.99 13.9
448 2nd Blocking Frequency Hz 0.00 ... 999.99 13.9
449 Frequency Hysteresis Hz 0.00 ... 100.00 13.9
Multifunctional input 1
450 Tolerance Band % 0.00 ... 25.00 14.1.1.3
451 Filter Time Constant ms Selection 14.1.1.4
453 Error/Warning Behavior - Selection 14.1.1.5
454 Point X1 % 0.00 ... 100.00 14.1.1.1
455 Point Y1 % -100.00 ... 100.00 14.1.1.1
456 Point X2 % 0.00 ... 100.00 14.1.1.1
457 Point Y2 % -100.00 ... 100.00 14.1.1.1
Positioning
459 Signal Source - Selection 11.6.1
460 Positioning Distance U 0.000 ... 1 106 11.6.1
461 Signal Correction ms -327.68 ... 327.67 11.6.1
462 Load Correction - -32768 ... 32767 11.6.1
463 Activity after Positioning - Selection 11.6.1
464 Waiting Time ms 0 ... 3.6 106 11.6.1
Temperature Adjustment
465 Operation mode - Selection 17.7.2
466 Temperature Coefficient %/100 0.00 ... 300.00 17.7.2
467 Adjusting Temperature deg.C -50.0 ... 300.0 17.7.2
Positioning
469 Reference Orientation ° 0.0 ... 359.9 11.6.2
471 Positioning Frequency Hz 1.00 ... 50.00 11.6.2
472 Max positional error ° 0.1 ... 90.0 11.6.2
Motor Potentiometer
473 Ramp Keypad-Motorpoti Hz/s 0.01 ... 999.99 13.10
Frequency Reference Channel
475 Reference Frequency Source - Selection 13.4
Reference percentage channel
476 Reference Percentage Source - Selection 13.5
Percentage ramp
477 Gradient Percentage Ramp %/s 0 ... 60000 13.8
478 Actual Percentage source - Selection 16.3
Positioning
479 time constant positioning controller ms 1.00 ... 9999.99 11.6.2

Fixed Frequencies
480 Fixed Frequency 1 Hz -999.99 ... 999.99 13.6.1
489 JOG-Frequency Hz -999.99 ... 999.99 13.6.2
Speed Sensor 1
491 Division marks - 1 ... 8192 9.4.2
Repetition frequency input
497 Divider - 1 ... 8192 13.11
Logic Modules
Brake Chopper
506 Trigger Threshold V Udmin+25 ... 1000.0 17.4
Motor Chopper
507 Trigger Threshold V Udmin+25 ... 1000.0 17.7.1
Digital Outputs
510 Setting Frequency Hz 0.00 ... 999.99 14.3.1
Percentage Value Limits
518 Minimum Reference Percentage % 0.00 ... 300.00 13.3
519 Maximum Reference Percentage % 0.00 ... 300.00 13.3
Fixed Percentages
520 Fixed Percentage 1 % -300.00 ... 300.00 13.6.3
Digital Outputs
530 Op. Mode Digital Output 1 - Selection 14.3
532 Op. Mode Digital Output 3 - Selection 14.3
536 Create Warning Mask - Selection 14.3.7
540 Op. Mode Comparator 1 - Selection 14.5.2
541 Comparator On above % -300.00 ... 300.00 14.5.2
542 Comparator Off below % -300.00 ... 300.00 14.5.2
543 Op. Mode Comparator 2 - Selection 14.5.2
544 Comparator On above % -300.00 ... 300.00 14.5.2
545 Comparator Off below % -300.00 ... 300.00 14.5.2
549 Max. Control Deviation % 0.01 ... 20.00 14.3.2
Multifunctional output 1
551 Voltage 100% V 0.0 ... 24.0 14.2.1.1
552 Voltage 0% V 0.0 ... 24.0 14.2.1.1
553 Analog Operation - Selection 14.2.1
554 Digital Operation - Selection 14.3
555 Repetition Freq. Operation - Selection 14.2.2
556 Division marks - 30 ... 8192 14.2.2.1
570 Motor Temp. Operation Mode - Selection 12.6

Motor Circuit Breaker
572 Frequency Limit % 0 ... 300 14.2.2.1
Intelligent current limits
574 Power Limit % 40.00 ... 95.00 16.1
575 Limitation Time min 5 ... 300 16.1
576 Phase Supervision - Selection 12.7
578 Allowed No. of Auto-Acknowl. - 0 ... 20 12.7
579 Restart Delay ms 0 ... 1000 12.8
Pulse Width Modulation
580 Reduction Limit Heat Sink Temp. deg.C -25 ... 0 17.1
V-belt Monitoring
582 Trigger Limit Iactive % 0.1 ... 100.0 17.6
583 Delay Time s 0.1 ... 600.0 17.6
V/f characteristic
600 Starting Voltage V 0.0 ... 100.0 15
601 Voltage Rise % -100 ... 200 15
602 Rise Frequency % 0 ... 100 15
603 Cut-Off Voltage V 60.0 ... 560.0 15
604 Cut-Off Frequency Hz 0.00 ... 999.99 15
605 Dyn. Voltage Pre-Control % 0 ... 200 15.1
Current limit value controller
611 Amplification - 0.01 ... 30.00 16.4.2
612 Integral Time ms 1 10000 16.4.2
613 Current Limit A 0.0 ... o ⋅ IFIN 16.4.2
614 Frequency Limit Hz 0.00 ... 999.99 16.4.2
Starting Behavior
621 Amplification - 0.01 ... 10.00 11.1.1
622 Integral Time ms 1 ... 30000 11.1.1
623 Starting Current A 0.0 ... o ⋅ IFIN 11.1.1.1
624 Frequency Limit Hz 0.00 ... 100.00 11.1.1.2
Stopping Behavior
Direct current brake
631 Braking Current A 0.00 ... √2⋅IFIN 11.3
632 Braking Time s 0.0 ... 200.0 11.3
633 Demagnetizing Time s 0.1 ... 30.0 11.3
634 Amplification - 0.00 ... 10.00 11.3
635 Integral Time ms 0 ... 1000 11.3
Stopping Behavior
637 Switch-Off Threshold % 0.0 ... 100.0 11.2.1
638 Holding Time s 0.0 ... 200.0 11.2.2

Search Run
646 Brak. Time after Search Run s 0.0 ... 200.0 11.5
647 Current / Rated Motor Current % 1.00 ... 100.00 11.5
648 Amplification - 0.00 ... 10.00 11.5
649 Integral Time ms 0 ... 1000 11.5
Auto Start
Slip compensation
661 Amplification % 0.0 ... 300.0 16.4.1
662 Max. Slip Ramp Hz/s 0.01 ... 650.00 16.4.1
663 Minimum Frequency Hz 0.01 ... 999.99 16.4.1
Voltage controller
671 Mains Failure Threshold V -200.0 ... –50.0 16.2
672 Reference Mains Support Value V -200.0 ... –10.0 16.2
673 Mains Support Deceleration Hz/s 0.01 ... 9999.99 16.2
674 Acceleration on Mains Resumption Hz/s 0.00 ... 9999.99 16.2
675 Shutdown Threshold Hz 0.00 ... 999.99 16.2
676 Reference Shutdown Value V Udmin+25 ... Udmax-25 16.2
677 Amplification - 0.00 ... 30.00 16.2
678 Integral Time ms 0 ... 10000 16.2
680 Reference DC-Link Limitation V Udmin+25 ... Udmax-25 16.2
681 Max. Frequency Rise Hz 0.00 ... 999.99 16.2
683 Gen. Ref. Current Limit A 0.0 ... o ⋅ IFIN 16.2
Current Controller
700 Amplification - 0.00 ... 2.00 16.5.1
701 Integral Time ms 0.00 ... 10.00 16.5.1
713 Magnetizing Current 50% Flux % 1 ... 50 9.2.3
716 Rated Magnetizing Current A 0.01⋅IFIN ... o⋅IFIN 9.2.3
Field Controller
717 Reference Flux % 0.01 ... 300.00 16.5.5
718 Rated Slip Correction Factor % 0.01 ... 300.00 9.2.4
Frequency Limits
719 Slip Frequency % 0 ... 10000 13.1
Speed controller
721 Amplification 1 - 0.00 ... 200.00 16.5.3
722 Integral Time 1 ms 0 ... 60000 16.5.3
723 Amplification 2 - 0.00 ... 200.00 16.5.3
724 Integral Time 2 ms 0 ... 60000 16.5.3
Acceleration Pre-Control
726 Minimum Acceleration Hz/s 0.1 ... 6500.0 16.5.4
727 Mech. Time Constant ms 1 ... 60000 16.5.4

Speed controller
728 Current Limit A 0.0 ... o ⋅ IFIN 16.5.3.1
729 Current Limit Generator Operation A -0.1 ... o ⋅ IFIN 16.5.3.1
730 Torque Limit % 0.00 ... 650.00 16.5.3.1
731 Torque Limit Generator Operation % 0.00 ... 650.00 16.5.3.1
732 P-Comp. Torque Upper Limit % 0.00 ... 650.00 16.5.3.1
733 P-Comp. Torque Lower Limit % 0.00 ... 650.00 16.5.3.1
Speed controller
734 Isq Limit Source Motor Operation - Selection 16.5.3.2
735 Isq Limit Source Generator Op. - Selection 16.5.3.2
736 Torque Limit Source Motor Op. - Selection 16.5.3.2
737 Torque Limit Source Gen. Op. - Selection 16.5.3.2
738 Speed Control Switch-Over Limit Hz 0.00 ... 999.99 16.5.3
739 Power Limit kW 0.00 ... 2⋅o⋅PFIN 16.5.3.1
740 Power Limit Generator Operation kW 0.00 ... 2⋅o⋅PFIN 16.5.3.1
Field Controller
741 Amplification - 0.0 ... 100.0 16.5.5
742 Integral Time ms 0.0 ... 1000.0 16.5.5
743 Ref. Isd Upper Limit A 0.1⋅IFIN ... o⋅IFIN 16.5.5.1
744 Ref. Isd Lower Limit A -IFIN ... IFIN 16.5.5.1
Speed controller
748 Backlash Damping % 0 ... 300 16.5.3
Modulation Controller
750 Reference Modulation % 3.00 ... 105.00 16.5.6
752 Integral Time ms 0.0 ... 1000.00 16.5.6
755 Reference Imr Lower Limit A 0.01⋅IFIN ... o⋅IFIN 16.5.6.1
756 Control Deviation Limitation % 0.00 ... 100.00 16.5.6.1
Encoder Monitoring
761 Timeout: Signal Fault ms 0 ... 65000 17.7.3
762 Timeout: Channel fault ms 0 ... 65000 17.7.3
763 Timeout: Direction fault ms 0 ... 65000 17.7.3
Torque Controller
767 Frequency Upper Limit Hz -999.99 ... 999.99 16.5.2
768 Frequency Lower Limit Hz -999.99 ... 999.99 16.5.2
769 Frequency Upper Limit Source - Selection 16.5.2.1
770 Frequency Lower Limit Source - Selection 16.5.2.1
Starting Behavior
780 Max. Flux-Formation Time ms 1 ... 10000 11.1.2
781 Current during Flux Formation A 0.1⋅IFIN ... o⋅IFIN 11.1.2

Timer
790 Operation Mode Timer 1 - Selection 14.5.1
791 Time 1 Timer 1 s/m/h 0 ... 650.00 14.5.1
792 Time 2 Timer 1 s/m/h 0 ... 650.00 14.5.1
793 Operation Mode Timer 2 - Selection 14.5.1
794 Time 1 Timer 2 s/m/h 0 ... 650.00 14.5.1
795 Time 2 Timer 2 s/m/h 0 ... 650.00 14.5.1
Self-configuration
796 SETUP Select - Selection 7.5

Bonfiglioli has been designing and developing innovative
and reliable power transmission and control solutions
for industry, mobile machinery and renewable energy
applications since 1956.
www.bonfiglioli.com
Bonfiglioli Riduttori S.p.A. tel: +39 051 647 3111 VEC 211 R4
Via Giovanni XXIII, 7/A fax: +39 051 647 3126
40012 Lippo di Calderara di Reno [email protected]
Bologna, Italy www.bonfiglioli.com

Man Act GB Vec211r4

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Man Act GB Vec211r4

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Man Act GB Vec211r4

Uploaded by

Copyright:

Available Formats

ACTIVE

For better clarity, the documentation is structured according to the customer-specific

Quick Start Guide

06/07 Operating Instructions ACTIVE 1

1 General Safety Instructions and Information on Use .................................................... 8

5 Electrical Installation ................................................................................................... 31

2 Operating Instructions ACTIVE 06/07

6 Control Unit KP500 ...................................................................................................... 56

7 Commissioning of the Frequency Inverter................................................................... 70

06/07 Operating Instructions ACTIVE 3

8 Inverter Data ............................................................................................................... 84

9 Machine Data ............................................................................................................... 89

10 System Data ................................................................................................................. 94

11 Operational Behavior ................................................................................................... 95

4 Operating Instructions ACTIVE 06/07

13 Reference Values........................................................................................................ 113

14 Control Inputs and Outputs ....................................................................................... 128

15 V/f - Characteristic..................................................................................................... 156

16 Control Functions ....................................................................................................... 158

17 Special Functions ....................................................................................................... 182

6 Operating Instructions ACTIVE 06/07

18 Actual Values.............................................................................................................. 192

19 Error Protocol ............................................................................................................. 197

20 Operational and Error Diagnosis ................................................................................ 201

21 Parameter List............................................................................................................ 204

06/07 Operating Instructions ACTIVE 7

1.1 General Information

8 Operating Instructions ACTIVE 06/07

1.3 Transport and Storage

1.4 Handling and Installation

06/07 06/07 Operating Instructions

1.6 Information on Use

1.7 Maintenance and Service

06/07 06/07 Operating

06/07 06/07 Operating

06/07 06/07 Operating

Ambient Operation: 0 … 55 °C; for exceeding 40 °C comply with the derating.

Climate class Operation: 3K3 (EN60721-3-3)

Mounting altitude Up to 1000 m at rated operating conditions.

Storage According to EN 50178;

Parameterization − Freely programmable digital inputs and outputs

Control terminal X210A Control terminal X210B

Relay output X10

Technical data of the control terminals

06/07 06/07 Operating

06/07 06/07 Operating

Mains voltage U V 320 ... 528

Mains voltage U V 320 ... 528

06/07 06/07 Operating

Mains voltage U V 320 ... 528

06/07 06/07 Operating

Mains voltage U V 320 ... 528

1000 2000 3000 4000 1000 2000 3000 4000

0 400 420 440 460 480

06/07 06/07 Operating

Dimensions in mm Installation dimensions in mm

fixing bracket top