Scribd
Upload
224 views2 pages

1-11-B 1. Tools and Equipment: Deadline Anchor Maintenance

Uploaded by

Abdul Hameed Omar

1. The document provides procedures for deadline anchor maintenance, including sensator adjustment and routine maintenance. 2. Sensator adjustment procedures include checking the 5/8" gap, pumping fluid into the sensator if needed, and checking that the weight indicator reads 27 kDaN. 3. Routine maintenance involves hanging off the top drive, checking for wear and that pins and bolts are secure, and inspecting for leaks.

Copyright:

© All Rights Reserved
Download as DOC, PDF, TXT or read online from Scribd
Download as doc, pdf, or txt

1-11-B 1. Tools and Equipment: Deadline Anchor Maintenance

Uploaded by

Abdul Hameed Omar
224 views2 pages
1. The document provides procedures for deadline anchor maintenance, including sensator adjustment and routine maintenance. 2. Sensator adjustment procedures include checking the 5/8" gap, pumping fluid into the sensator if needed, and checking that the weight indicator reads 27 kDaN. 3. Routine maintenance involves hanging off the top drive, checking for wear and that pins and bolts are secure, and inspecting for leaks.

Original Description:

for dead anchore

Original Title

Deadline

Copyright

© © All Rights Reserved

Available Formats

DOC, PDF, TXT or read online from Scribd

Did you find this document useful?

Is this content inappropriate?

1. The document provides procedures for deadline anchor maintenance, including sensator adjustment and routine maintenance. 2. Sensator adjustment procedures include checking the 5/8" gap, pumping fluid into the sensator if needed, and checking that the weight indicator reads 27 kDaN. 3. Routine maintenance involves hanging off the top drive, checking for wear and that pins and bolts are secure, and inspecting for leaks.

Copyright:

© All Rights Reserved
Download as DOC, PDF, TXT or read online from Scribd
Download as doc, pdf, or txt
224 views2 pages

1-11-B 1. Tools and Equipment: Deadline Anchor Maintenance

Uploaded by

Abdul Hameed Omar
1. The document provides procedures for deadline anchor maintenance, including sensator adjustment and routine maintenance. 2. Sensator adjustment procedures include checking the 5/8" gap, pumping fluid into the sensator if needed, and checking that the weight indicator reads 27 kDaN. 3. Routine maintenance involves hanging off the top drive, checking for wear and that pins and bolts are secure, and inspecting for leaks.

Copyright:

© All Rights Reserved
Download as DOC, PDF, TXT or read online from Scribd
Download as doc, pdf, or txt
You are on page 1/ 2

1-11-B

DEADLINE ANCHOR MAINTENANCE


1. TOOLS AND EQUIPMENT
MEASURING TAPE / NOZZLE GAUGE / SST GAUGE
MARTIN DECKER FLUID
MARTIN DECKER PUMP
ADJUSTABLE SPANNER
ASSOCIATED PUBLICATIONS
LEVER
HAMMER WRENCH / HAMMER

2. SAFETY INFORMATION AND PRECAUTIONS


HOLD A PRE-JOB SAFETY MEETING.

DEADLINE ANCHOR MAINTENANCE IS NORMALLY DONE WHILE SLIP OR CUT


DRILLING LINE. TO BE CARRIED OUT UNDER THE SUPERVISION OF THE DRILLER/
TOURPUSHER/TOOLPUSHER.

TRAVELLING BLOCK MUST BE HUNG OFF FOR MAINTENANCE ROUTINE.

ENSURE PUMP AND W-15 FLUID IS CLEAN, BEFORE PUMPING UP


SENSATOR.

3. PROCEDURES
3.1 FOR SENSATOR ADJUSTMENT
1. REMOVE ANCHOR GUARDS IF APPLICABLE.

2. CHECK GAP ON THE SENSATOR. GAP SHOULD BE 5/8" AND CAN BE


MEASURED WITH A NOZZLE GAUGE , OR HAVE THE MECHANIC MAKE A
GAUGE FROM 1/8" STAINLESS STEEL 4" LONG X 1" WIDE WITH A 5/8" WIDE X
3/4" LONG SECTION CUT OUT AT ONE END AND A HOLE AT THE OTHER END
TO HANG THE GAUGE ON THE UNIT.

3. IF GAP IS SMALLER THAN 5/8" CHECK HOSES AND SENSATOR. ALSO


CHECK DRILLERS CONSOLE AT HOSE BLOCK AND GAUGE PIPING FOR
POSSIBLE LEAKS.

4. REMOVE PROTECTION NUT, INSTALL PUMP LOOSELY ON FITTING


AND FILL WITH FLUID. PUMP AND ALLOW A LITTLE FLUID TO LEAK AND
EXPEL ANY AIR IN PUMP. TIGHTEN PUMP AND PUMP FLUID UNTIL SLIGHT
MOVEMENT IS INDICATED AT THE WEIGHT INDICATOR GAUGE.

5. CHECK GAP, PUMP MORE IF NECESSARY AND BLEED OFF ANY OVER
PRESSURE AT THE LINE ANCHOR CHECK VALVE.
6. REFIT PROTECTION NUT.

NOTE: SENSATOR CAN BE PUMPED UP WITH BLOCKS HUNG


OFF OR WITH TOP DRIVE WEIGHT.

_______________________________________________________________
PPC Manual Sept 95 Rev/1 Page 1
1-11-B
DEADLINE ANCHOR MAINTENANCE
A) WITH TOP DRIVE HUNG, PUMP UP UNTIL SLIGHT WEIGHT INDICATED
THENBLEED OFF TO ZERO. WHEN PICKING UP ENSURE WEIGHT INDICATOR
READS 27 K DaN.

B) WITH TOP DRIVE ONLY HANGING IN MAST, PUMP UP TO 5/8" GAP ON


SENSATOR AND CHECK WEIGHT INDICATOR READS 27 K DaN.

C) SENSATOR SHOULD BE CHECKED PRIOR TO JARRING OR IF


EXPERIENCING TIGHT HOLE WITH EXCESSIVE OVERPULL.

THE PREFERRED METHOD FOR SENSATOR ADJUSTMENT IS METHOD "A".

METHOD "B" SHOULD ONLY BE USED IN A SITUATION WHERE IT IS


IMPRACTICAL TO HANG THE TOP DRIVE AT THE TIME.

3.2 FOR ROUTINE MAINTENANCE


1. HANG OFF TOP DRIVE ON BLOCK HANGING LINE.

2. CHECK WEAR IN SENSATOR PINS, AND THAT SPLIT PINS ARE IN PLACE.

3. CHECK TIE DOWN BOLTS ARE TIGHT.

4. CHECK NUT TIGHT ON LINE GUARD BOLTS.

5. CHECK NO LEAKS ON SENSATOR AND FITTINGS.

6. CHECK BOLTS ON LINE CLAMP ARE TIGHT.

_______________________________________________________________
PPC Manual Sept 95 Rev/1 Page 2

You might also like