Scribd Logo
Upload

Welcome to Scribd!

  • 111 views

    HP Procurve Switch - Basic Configuration Guide II

    Uploaded by

    பாரதி ராஜா
    This document provides instructions for configuring basic network settings and SNMP on an HP Procurve switch, including enabling DHCP relay, configuring RSTP, enabling IP routing between VLANs, resetting to factory defaults, enabling remote logging, and securing the switch by configuring SNMPv3 with users, groups, and disabling insecure SNMPv1/v2c access. Useful troubleshooting commands are also listed.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    HP Procurve Switch - Basic Configuration Guide II

    Uploaded by

    பாரதி ராஜா
    111 views1 page
    This document provides instructions for configuring basic network settings and SNMP on an HP Procurve switch, including enabling DHCP relay, configuring RSTP, enabling IP routing between VLANs, resetting to factory defaults, enabling remote logging, and securing the switch by configuring SNMPv3 with users, groups, and disabling insecure SNMPv1/v2c access. Useful troubleshooting commands are also listed.

    Original Description:

    procurve

    Original Title

    HP Procurve Switch – Basic Configuration Guide II

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for configuring basic network settings and SNMP on an HP Procurve switch, including enabling DHCP relay, configuring RSTP, enabling IP routing between VLANs, resetting to factory defaults, enabling remote logging, and securing the switch by configuring SNMPv3 with users, groups, and disabling insecure SNMPv1/v2c access. Useful troubleshooting commands are also listed.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    111 views1 page

    HP Procurve Switch - Basic Configuration Guide II

    Uploaded by

    பாரதி ராஜா
    This document provides instructions for configuring basic network settings and SNMP on an HP Procurve switch, including enabling DHCP relay, configuring RSTP, enabling IP routing between VLANs, resetting to factory defaults, enabling remote logging, and securing the switch by configuring SNMPv3 with users, groups, and disabling insecure SNMPv1/v2c access. Useful troubleshooting commands are also listed.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    HP Procurve Switch – Basic Configuration Guide II ITAdminGuide.

    com

    InterVLAN routing DHCP Relay Configure SNMPv3

    (config)# vlan 192 !disable default and insecure snmp community


    (vlan-192)# ip helper-address 172.20.100.1
    (config)# no snmp-server community public

    Configure Rapid Spanning Tree Protocol (config)# snmpv3 enable


    Creating user 'initial'
    Authentication Protocol: MD5
    (config)# spanning-tree
    Enter authentication password: **********
    !Use RSTP (Rapid STP) instead, because of Privacy protocol is DES
    slow convergence of STP Enter privacy password: **********

    User 'initial' is created


    (config)# spanning-tree force-version rstp-operation
    Would you like to create a user that uses SHA? n
    !Inorder for users VLAN to communicate
    with Server VLAN Useful Troubleshooting Commands (self explanatory) User creation is done. SNMPv3 is now functional.
    (config)# ip routing Would you like to restrict SNMPv1 and SNMPv2c messages to have read only
    show system information access (you can set this later by the command 'snmp restrict-access'): y
    show vlans
    Reset to factory default show mac-address b40c25-ff6613 !If you want to add user to Manager group, privileged.
    show trunks !SNMPv3 access group should only use ver3 security model.
    (config)# erase startup-config show lacp (config)# snmpv3 group managerpriv user cacti sec-model ver3
    Configuration will be deleted and device show spanning-tree
    rebooted, continue [y/n]? Y show power-over-ethernet brief !If you want to add user to Operator group, unprivileged.
    !summary of network traffic of each port (config)# snmpv3 group operatorauth user cacti sec-model ver3
    show int display
    Enable Remote Logging (syslog) !Event logs !Specify your preferred username and password
    log –r //most recent first (config)# snmpv3 user cacti auth md5 authenticationpass priv aes privatepass
    (config)# logging 172.20.100.155 log [IP address] //events of specific IP
    !delete default initial user for security reasons.
    (config)# no snmpv3 user initial
    Configure SNMPv1 and SNMPv2c
    OPTIONAL
    !completely turn off snmpv1/2
    !ITADMINCOM is community string. 172.20.100.150 is trap receiver.
    (config)# snmpv3 only
    (config)# snmp-server host 172.20.100.150 ITADMINCOM
    !Allow your server for operator access to HP switch
    !community with manager privilege can access all MIB objects, but read-only.
    (config)# ip authorized-managers 172.20.100.150 255.255.255.255 access operator
    config)# snmp-server community ITADMINCOM manager restricted
    TROUBLESHOOTING
    !community with operator privilege can access all MIB objects except CONFIG MIB, but read-only
    !To view all snmpv3 users
    config)# snmp-server community ITADMINCOM operator restricted
    (config)# show snmpv3 user
    TROUBLESHOOTING
    !To view all snmpv3 groups
    !displays information on all SNMP communities, trap receivers, traps information
    (config)# show snmpv3 groups
    (config)# show snmp-server

    ITAdminGuide.com Version 1.0

    You might also like