LM2825 Integrated Power Supply 1A DC-DC Converter

May 1997

LM2825
Integrated Power Supply 1A DC-DC Converter
General Description Features
The LM2825 is a complete 1A DC-DC Buck converter pack- n Minimum design time required
aged in a 24-lead molded Dual-In-Line integrated circuit n 3.3V, 5V and 12V fixed output versions
package. n Two adjustable versions allow 1.23V to 15V outputs
Contained within the package are all the active and passive n Wide input voltage range, up to 40V
components for a high efficiency step-down (buck) switching n Low-power standby mode, IQ typically 65 µA
regulator. Available in fixed output voltages of 3.3V, 5V and n High efficiency, typically 80%
12V, as well as two adjustable versions, these devices can n ± 4% output voltage tolerance
provide up to 1A of load current with fully guaranteed electri-
n Excellent line and load regulation
cal specifications.
n TTL shutdown capability/programmable Soft-start
Self-contained, this converter is also fully protected from out-
n Thermal shutdown and current limit protection
put fault conditions, such as excessive load current, short
circuits, or excessive temperatures. n −40˚C to +85˚C ambient temperature range

Highlights Applications
n No external components required (fixed output voltage n Simple high-efficiency step-down (buck) regulator
versions) n On-card switching regulators
n Integrated circuit reliability n Efficient pre-regulator for linear regulators
n MTBF over 20 million hours n Distributed power systems
n Radiated EMI meets Class B stipulated by CISPR 22 n DC/DC module replacement
n High power density, 35 W/in3
n 24-pin DIP package profile (1.25 x 0.54 x 0.26 inches)

Connection Diagram

DS012661-27

Standard Application
(Fixed output voltage versions)

DS012661-2

“NC (Do not use)” pins: See Figure 11.

Top View
DS012661-1
Ordering Information
Order Number LM2825N-3.3, LM2825N-5.0, LM2825N-12,
Radiated EMI LM2825N-ADJ or LM2825HN-ADJ
Radiated emission of electromagnetic fields is measured at See NS Package Number NA24F
10m distance. The emission levels are within the Class B
limits stipulated by CISPR 22.
30. . . .230 MHz 30 dB µV/m
230. . . .1000 MHz 37 dB µV/m
1. . . .10 GHz 46 dB µV/m

© 1997 National Semiconductor Corporation DS012661 www.national.com

 Absolute Maximum Ratings (Note 1) ESD Susceptibility
If Military/Aerospace specified devices are required, Human Body Model (Note 3) 2 kV
please contact the National Semiconductor Sales Office/ Lead Temperature (Soldering 10 sec.) 260˚C
Distributors for availability and specifications.
Maximum Input Supply (VIN) +45V Operating Ratings
SD/SS Pin Input Voltage (Note 2) 6V Ambient Temperature Range −40˚C ≤ TA ≤ +85˚C
Output Pin Voltage Junction Temperature Range −40˚C ≤ TJ ≤ +125˚C
(3.3V, 5.0V and ADJ) −1V ≤ V ≤ 9V Input Supply Voltage (3.3V version) 4.75V to 40V
(12V and H-ADJ) −1V ≤ V ≤ 16V Input Supply Voltage (5V version) 7V to 40V
ADJ Pin Voltage (ADJ, H-ADJ only) −0.3V ≤ V ≤ 25V Input Supply Voltage (12V version) 15V to 40V
Power Dissipation Internally Limited Input Supply Voltage (-ADJ, H-ADJ) 4.5V to 40V
Storage Temperature Range −40˚C to +125˚C

LM2825-3.3 Electrical Characteristics (Note 4)

Specifications with standard type face are for TA = 25˚C, and those with boldface type apply over full Operating Tempera-
ture Range. Test Circuit Figure 2.
Symbol Parameter Conditions LM2825-3.3 Units
Typical Limit (Limits)
(Note 6) (Note 7)
VOUT Output Voltage 4.75V ≤ VIN ≤ 40V, 0.1A ≤ ILOAD ≤ 1A 3.3 V
3.168/3.135 V(min)
3.432/3.465 V(max)
Line Regulation 4.75V ≤ VIN ≤ 40V 1.5 mV
ILOAD = 100 mA
Load Regulation 0.1A ≤ ILOAD ≤ 1A 8 mV
VIN = 12V
Output Ripple Voltage VIN = 12V, ILOAD = 1A 40 mV p-p
η Efficiency VIN = 12V, ILOAD = 0.5A 75 %

LM2825-5.0 Electrical Characteristics (Note 4)

Specifications with standard type face are for TA = 25˚C, and those with boldface type apply over full Operating Tempera-
ture Range. Test Circuit Figure 2.
Symbol Parameter Conditions LM2825-5.0 Units
Typical Limit (Limits)
(Note 6) (Note 7)
VOUT Output Voltage 7V ≤ VIN ≤ 40V, 0.1A ≤ ILOAD ≤ 1A 5.0 V
4.800/4.750 V(min)
5.200/5.250 V(max)
Line Regulation 7V ≤ VIN ≤ 40V 2.7 mV
ILOAD = 100 mA
Load Regulation 0.1A ≤ ILOAD ≤ 1A 8 mV
VIN = 12V
Output Ripple Voltage VIN = 12V, ILOAD = 1A 40 mV p-p
η Efficiency VIN = 12V, ILOAD = 0.5A 80 %

www.national.com 2
 LM2825-12 Electrical Characteristics (Note 4)
Specifications with standard type face are for TA = 25˚C, and those with boldface type apply over full Operating Tempera-
ture Range. Test Circuit Figure 2.
Symbol Parameter Conditions LM2825-12 Units
Typical Limit (Limits)
(Note 6) (Note 7)
VOUT Output Voltage 15V ≤ VIN ≤ 40V, 0.1A ≤ ILOAD ≤ 0.75A 12.0 V
11.52/11.40 V(min)
12.48/12.60 V(max)
Line Regulation 15V ≤ VIN ≤ 40V 8.5 mV
ILOAD = 100 mA
Load Regulation 0.1A ≤ ILOAD ≤ 0.75A 12 mV
VIN = 24V
Output Ripple Voltage VIN = 24V, ILOAD = 1A 100 mV p-p
η Efficiency VIN = 24V, ILOAD = 0.5A 87 %

LM2825-ADJ Electrical Characteristics (Note 5)

Specifications with standard type face are for TA = 25˚C, and those with boldface type apply over full Operating Tempera-
ture Range. Test Circuit Figure 3.
Symbol Parameter Conditions LM2825-ADJ Units
Typical Limit (Limits)
(Note 6) (Note 7)
VADJ Adjust Pin Voltage 4.5V ≤ VIN ≤ 40V, 0.1A ≤ ILOAD ≤ 1A 1.230 V
1.23V ≤ VOUT ≤ 8V 1.193/1.180 V(min)
1.267/1.280 V(max)
η Efficiency VIN = 12V, ILOAD = 0.5A 74 %
VOUT Programmed for 3V. See Circuit of Figure 3

LM2825H-ADJ Electrical Characteristics (Note 5)

Specifications with standard type face are for TA = 25˚C, and those with boldface type apply over full Operating Temperature
Range. Test Circuit Figure 3.
Symbol Parameter Conditions LM2825H-ADJ Units
Typical Limit (Limits)
(Note 6) (Note 7)
VADJ Adjust Pin Voltage 9V ≤ VIN ≤ 40V, 0.1A ≤ ILOAD ≤ 0.55A 1.230 V
7V ≤ VOUT ≤ 15V 1.193/1.180 V(min)
1.267/1.280 V(max)
η Efficiency VIN = 24V, ILOAD = 0.5A 87 %
VOUT Programmed for 12V.
See Circuit of Figure 3

3 www.national.com
 All Output Voltage Versions Electrical Characteristics
Specifications with standard type face are for TA = 25˚C, and those with boldface type apply over full Operating Range. Un-
less otherwise specified, VIN = 12V for 3.3V, 5.0V and ADJ versions, VIN = 24V for 12V and H-ADJ versions, ILOAD = 100 mA.
Symbol Parameter Conditions LM2825-XX Units
Typical Limit (Limits)
(Note 6) (Note 7)
ICL DC Output Current RL = 0Ω 1.4 A
Limit
1.2 A(min)
2.4 A(max)
IQ Operating Quiescent SD/SS Pin = 3.1V 5 mA
Current
(Note 8) 10 mA(max)
ISTBY Standby Quiescent SD/SS Pin = 0V 65 µA
Current
(Note 8) 200 µA(max)
IADJ Adjust Pin Bias Current Adjustable Versions Only, VFB = 1.3V 6 nA
50/100 nA(max)
fO Oscillator Frequency (Note 9) 150 kHz
θJA Thermal Resistance Junction to Ambient (Note 10) 30 ˚C/W
SHUTDOWN/SOFT-START CONTROL Test Circuit Figure 2
VSD Shutdown Threshold 1.3 V
Voltage
Low (Shutdown Mode) 0.6 V(max)
High (Soft-start Mode) 2.0 V(min)
VSS Soft-start Voltage VOUT = 20% of Nominal Output Voltage 2 V
VOUT = 100% of Nominal Output Voltage 3
ISD Shutdown Current VSHUTDOWN = 0.5V 5 µA
(Note 8) 10 µA(max)
ISS Soft-start Current VSOFT-START = 2.5V 1.6 µA
(Note 8) 5 µA(max)
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is in-
tended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics.
Note 2: Voltage internally clamped. If clamp voltage is exceeded, limit current to a maximum of 5 mA.
Note 3: The human body model is a 100 pF capacitor discharged through a 1.5k resistor into each pin.
Note 4: When the LM2825 is used as shown in Figure 2 test circuit, system performance will be as shown in Electrical Characteristics.
Note 5: When the LM2825 is used as shown in Figure 3 test circuit, system performance will be as shown in Electrical Characteristics.
Note 6: Typical numbers are at 25˚C and represent the most likely norm.
Note 7: All limits guaranteed at room temperature (standard type face) and at temperature extremes (bold type face) when output current is limited to the value given
in the temperature derating curves. See the application section for curves. All limits at temperature extremes are guaranteed using standard Statistical Quality Control
(SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).
Note 8: ILOAD = 0A.
Note 9: The switching frequency is reduced when the second stage current limit is activated. The amount of reduction is determined by the severity of current over-
load.
Note 10: Junction to ambient thermal resistance (no external heat sink) for the DIP-24 package with the leads soldered to a printed circuit board with (1 oz.) copper
area of approximately 2 in2.

www.national.com 4
Typical Performance Characteristics (Circuits of Figure 2 and Figure 3) Unless otherwise specified,
VIN = 12V for 3.3V, 5.0V and ADJ versions, VIN = 24V for 12V and H-ADJ versions, ILOAD = 100 mA, TA = 25˚C

Normalized Efficiency Dropout Voltage

Output Voltage

DS012661-4 DS012661-5

DS012661-3

Line Regulation Load Regulation Output

Ripple Voltage

DS012661-6 DS012661-7

DS012661-8

Operating Shutdown Switching Frequency

Quiescent Current Quiescent Current

DS012661-11

DS012661-9 DS012661-10

5 www.national.com
 Typical Performance Characteristics (Circuits of Figure 2 and Figure 3) Unless otherwise specified,
VIN = 12V for 3.3V, 5.0V and ADJ versions, VIN = 24V for 12V and H-ADJ versions, ILOAD = 100 mA, TA = 25˚C (Continued)

Soft-start Shutdown /Soft-start Soft-start Response

Current

DS012661-12 DS012661-14

DS012661-13

Switch Current Adjust Pin

Limit Bias Current

DS012661-28 DS012661-29

Load Transient Response for Continuous Mode Load Transient Response for Discontinuous Mode
VIN = 20V, VOUT = 5V, IL = 250 mA to 750 mA VIN = 20V, VOUT = 5V, IL = 40 mA to 140 mA

DS012661-23
DS012661-24
A: Output Voltage 100 mV/div (AC)
A: Output Voltage 100 mV/div (AC)
B: 250 mA to 750 mA Load Pulse
B: 40 mA to 140 mA Load Pulse
Horizontal Time Base: 200 µs/div
Horizontal Time Base: 200 µs/div

FIGURE 1. Typical Load Transient Response

www.national.com 6
Test Circuit

DS012661-19

*Optional—Required if package is more than 6" away from main filter or bypass capacitor.
**Optional Soft-start Capacitor
VIN = 40V (max)
VOUT = 3.3V or 5V @ 1A or 12V @ 0.75A
FIGURE 2. Standard Test Circuit
(Fixed Output Voltage Versions)

DS012661-30

*Optional—Required if package is more than 6" away from main filter or bypass capacitor.
**Optional Soft-start Capacitor
***Optional—See Application Information.
VIN = 40V (max)
VOUT = 1.23V to 8V (LM2825-ADJ)
7V to 15V (LM2825H-ADJ)
ILOAD = IMAX (See derating curves)
FIGURE 3. Standard Test Circuit
(Adjustable Output Voltage Versions)

Application Information Select R2 with the following equation.

PROGRAMMING OUTPUT VOLTAGE

(Selecting R1 and R2 as shown in Figure 3)
The LM2825 is available in two adjustable output versions. When programming VOUT, keep in mind that VIN must be
The LM2825-ADJ has been optimized for output voltages greater than VOUT + 2V for proper operation.
between 1.23V and 8V, while the LM2825H-ADJ covers the
output voltage range of 7V to 15V. Both adjustable versions OPTIONAL EXTERNAL COMPONENTS
are set in the following way.
SOFT-START CAPACITOR
CSS: A capacitor on this pin provides the regulator with a
Soft-start feature (slow start-up). The current drawn from the
source starts out at a low average level with narrow pulses,
Select a value for R1 between 240Ω and 1.5 kΩ. The lower and ramps up in a controlled manner as the pulses expand
resistor values minimize noise pickup at the sensitive adjust to their steady-state width. This reduces the startup current
pin. (For lowest temperature coefficient and the best stability considerably, and delays and slows down the output voltage
with time, use 1% metal film resistors.) rise time.

7 www.national.com
 Application Information (Continued)

It is especially useful in situations where the input power VOUT R2 CFF

source is limited in the amount of current it can deliver, since LM2825-ADJ
you avoid loading down this type of power supply. 2 630 N/A
Under some operating conditions, a Soft-start capacitor is 3 1.43k N/A
required for proper operation. Figure 5 indicates the input
4 2.26k 2700 pF
voltage and ambient temperature conditions for which a
Soft-start capacitor may be required. 5 3.09k 2700 pF
This curve is typical for full guaranteed output current and 6 3.92k 2200 pF
can be used as a guideline. As the output current decreases, 7 4.75k 1800 pF
the operating area requiring a Soft-start capacitor de-
8 5.49k 1500 pF
creases. Capacitor values between 0.1 µF and 1 µF are rec-
ommended. Tantalum or ceramic capacitors are appropriate LM2825H-ADJ
for this application. 7 4.75k 2700 pF
8 5.49k 2200 pF
INPUT CAPACITOR
9 6.34k 1800 pF
CIN: An optional input capacitor is required if the package is
more than 6" away from the main filter or bypass capacitor. A 10 7.15k 1500 pF
low ESR aluminum or tantalum bypass capacitor is recom- 11 8.06k 1000 pF
mended between the input pin and ground to prevent large 12 8.87k 820 pF
voltage transients from appearing at the input. In addition, to
be conservative, the RMS current rating of the input capaci- 13 9.53k 680 pF
tor should be selected to be at least 1⁄2 the DC load current. 14 10.5k 680 pF
With a 1A load, a capacitor with a RMS current rating of at 15 11.3k 680 pF
least 500 mA is recommended.
The voltage rating should be approximately 1.25 times the FIGURE 4. CFF Selection Table
maximum input voltage. With a nominal input voltage of 12V,
an aluminum electrolytic capacitor (Panasonic HFQ series or SHUTDOWN
Nichicon PL series or equivalent) with a voltage rating
greater than 15V (1.25 x VIN) would be needed. The circuit shown in Figure 10 shows 2 circuits for the
Shutdown/Soft-start feature using different logic signals for
Solid tantalum input capacitors should only be used where shutdown and using a 0.1 µF Soft-start capacitor.
the input source is impedance current limited. High dV/dt ap-
plied at the input can cause excessive charge current THERMAL CONSIDERATIONS
through low ESR tantalum capacitors. This high charge cur-
The LM2825 is available in a 24-pin through hole DIP. The
rent can result in shorting within the capacitor. It is recom-
package is molded plastic with a copper lead frame. When
mended that they be surge current tested by the manufactur-
the package is soldered to the PC board, the copper and the
er.The TPS series available from AVX, and the 593D series
board are the heat sink for the LM2825.
from Sprague are both surge current tested.
Use caution when using ceramic capacitors for input bypass-
ing, because it may cause ringing at the VIN pin.

LOWERING OUTPUT RIPPLE

When using the adjustable parts, one can achieve lower out-
put ripple voltage by shorting a resistor internal to the
LM2825. However, if this resistor is shorted, a feed forward
capacitor must be used to keep the regulator stable. For this
reason, this resistor must be left open on all of the fixed out-
put voltage versions or instability will result. See the feed for-
ward capacitor selection below. Shorting the internal resistor
is accomplished by shorting pins 8 and 9 on the LM2825,
and will typically reduce output ripple by 25 to 33%.

FEED FORWARD CAPACITOR SELECTION (CFF)

When using an adjustable part and pins 8 and 9 are shorted
DS012661-22
to reduce output ripple, a feed forward capacitor is required.
This capacitor is typically between 680 pF and 2700 pF. The FIGURE 5. Usage of the Soft-start Capacitor
table of Figure 4 shows the value for CFF for a given output
voltage and feedback resistor R2 (R1 = 1 kΩ).

www.national.com 8
Application Information (Continued)

OUTPUT CURRENT DERATING FOR TJ = −40˚C to −25˚C AND TJ = −25˚C to 0˚C

At the lower temperature extremes, the switch current limit drops off sharply. As a result, a lower output current is available in this
temperature range. See Figure 6 and Figure 7 for the typical available output current at these temperature ranges.

DS012661-32

FIGURE 6. LM2825 Output Current Derating for TJ = −40˚C to −25˚C

DS012661-33

FIGURE 7. LM2825 Output Current Derating for TJ = −25˚C to 0˚C

9 www.national.com
 Application Information (Continued)

OUTPUT CURRENT DERATING FOR TA = 0˚C to 70˚C

Due to the limited switch current, the LM2825 cannot supply the full one ampere output current over the entire input and output
voltage range. Figure 8 shows the typical available output current for any input and output voltage combination. This applies for
all output voltage versions.

DS012661-34

FIGURE 8. LM2825 Output Current Derating for TA = 0˚C to 70˚C

OUTPUT CURRENT DERATING FOR TA = 70˚C to 85˚C

At high these high ambient temperatures, the LM2825 cannot supply the full one ampere over the entire input and output voltage
range. This is due to thermal reasons and Figure 9 shows the typical available output current for any input and output voltage
combination. This applies for all output voltage versions.

DS012661-35

FIGURE 9. LM2825 Output Current Derating for TA = 70˚C to 85˚C

www.national.com 10
Application Information (Continued)

DS012661-25

FIGURE 10. Typical Circuits Using Shutdown /Soft-start Features

TYPICAL THROUGH HOLE PC BOARD LAYOUT (2X SIZE), SINGLE SIDED, THROUGH HOLE PLATED

DS012661-26

Note: Holes are not shown.

“No Connect Pins” are connected to copper pads for thermal reasons only and must remain electrically isolated.
FIGURE 11. 2X Printed Circuit Board Layout

11 www.national.com
LM2825 Integrated Power Supply 1A DC-DC Converter
Physical Dimensions inches (millimeters) unless otherwise noted

24-Lead (0.600" Wide) Molded Dual-In-Line Package

Order Number LM2825N-3.3, LM2825N-5.0, LM2825N12, LM2825N-ADJ or LM2825HN-ADJ
NS Package Number NA24F

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DE-
VICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMI-
CONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or sys- 2. A critical component in any component of a life support
tems which, (a) are intended for surgical implant into device or system whose failure to perform can be rea-
the body, or (b) support or sustain life, and whose fail- sonably expected to cause the failure of the life support
ure to perform when properly used in accordance device or system, or to affect its safety or effectiveness.
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.

National Semiconductor National Semiconductor National Semiconductor National Semiconductor

Corporation Europe Hong Kong Ltd. Japan Ltd.
Americas Fax: +49 (0) 1 80-530 85 86 13th Floor, Straight Block, Tel: 81-3-5620-6175
Tel: 1-800-272-9959 Email: [email protected] Ocean Centre, 5 Canton Rd. Fax: 81-3-5620-6179
Fax: 1-800-737-7018 Deutsch Tel: +49 (0) 1 80-530 85 85 Tsimshatsui, Kowloon
Email: [email protected] English Tel: +49 (0) 1 80-532 78 32 Hong Kong
Français Tel: +49 (0) 1 80-532 93 58 Tel: (852) 2737-1600
www.national.com Italiano Tel: +49 (0) 1 80-534 16 80 Fax: (852) 2736-9960

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.