Digital Electronics Interview Questions

Digital Electronics Interview Questions
Check out These Most asked Digital Electronics Interview Questions and Answers
and see how many can you answer:
Ques1: What are the applications of Demultiplexer?

Answer: The applications of the demultiplexer are as follows:
1. It is used in the data transmission system with error detection.
2. It is used as a decoder for the conversion of binary to decimal.
3. It is used as a serial to parallel converter.
Ques2: What are the differences between Combinational Circuits and
Sequential Circuits?
Answer: The differences between combinational and sequential circuits are
as follows:
Combinational Circuits Sequential Circuits

These are faster in speed. These are slower.
These are easy to design. These are difficult to design.
The clock input is not required. The clock input is required.
In this, the memory units are not In this, the memory units are required to
required. store the previous values of inputs.
Example: Mux, Demux, encoder, Example: Shift registers, counters.
decoder, adders, subtractors.
Ques3: Define Rise Time?

Answer: Rise time is the time that is required to change the voltage level
from 10% to 90%.
Ques4: Define fall time?
Answer: Fall time is the time that is required to change the voltage level
from 90% to 10%.
Ques5: Define Setup time?
Answer: The minimum time that is required to maintain the constant voltage
levels at the excitation inputs of the flip-flop device before the triggering
edge of the clock pulse for the levels to be reliably clocked in the flip flop is
called the Setup time. It is denoted as tsetup.
Ques6: What is the difference between D-latch and D Flip-flop?
Downloaded From- RecruitmentResult.com Page 1

Answer: D-latch is level sensitive whereas flip-flop is edge sensitive. Flip-
flops are made up of latches.
Ques7: What is a Demultiplexer?
Answer: The demultiplexer is a circuit that receives the input on a single line
and transmits this onto 2n possible output line. A Demultiplexer of 2n
outputs has n select lines, which are used to select which output line is to be
sent to the input. The demultiplexer is also called as Data Distributor.
Ques8: What are the applications of Demultiplexer?

Answer: The applications of the demultiplexer are as follows:
1. It is used in the data transmission system with error detection.
2. It is used as a decoder for the conversion of binary to decimal.
3. It is used as a serial to parallel converter.
Ques9: What Is Difference Between Latch And Flip-flop?
Answer: The main difference between latch and FF is that latches are level
sensitive while FF is edge sensitive. They both require the use of clock signal
and are used in sequential logic. For a latch, the output tracks the input
when the clock signal is high, so as long as the clock is logic 1, the output
can change if the input also changes.
FF on the other hand, will store the input only when there is a rising/falling
edge of the clock. Latch is sensitive to glitches on enable pin, whereas flip-
flop is immune to glitches. Latches take fewer gates (also less power) to
implement than flip-flops. Latches are faster than flip-flops.
Ques10: How To Achieve 180 Degree Exact Phase Shift?
Answer: Never tell using inverter
a) DCM an inbuilt resource in most of FPGA can be configured to get 180
degree phase shift.
b) BUFGDS that is differential signaling buffers which are also inbuilt
resource of most of FPGA can be used.
Ques11: What is a Logic gate?
Answer: The basic gates that make up the digital system are called a logic
gate. The circuit that can operate on many binary inputs to perform a
particular logic function is called an electronic circuit.

Ques12: What is meant by K-Map or Karnaugh Map?
Answer: K-Map is a pictorial representation of truth table in which the map is
made up of cells, and each term in this represents the min term or max term
of the function. By this method, we can directly minimize the Boolean
function without following various steps.
Ques13: Name the two forms of Boolean expression?
Answer: The two forms of Boolean expression are:
1. Sum of products (SOP) form.
2. The Product of sum (POS) form.
Ques14: What are the limitations of the Karnaugh Map?

Answer: The limitations of Karnaugh Map are as follows:
1. It is limited to six variable maps which means more than six variable
involving expressions are not reduced.
2. These are useful for only simplifying Boolean expression which is
represented I standard form.
Ques15: What are the applications of Multiplexer (MUX)?

Answer: The applications of the multiplexer are as follows:
1. It is used as a data selector from many inputs to get one output.
2. It is used as A/D to D/A Converter.
3. These are used in the data acquisition system.
4. These are used in time multiplexing system.

Digital Electronics Interview Questions

Uploaded by

Copyright:

Available Formats

Digital Electronics Interview Questions

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Digital Electronics Interview Questions

Uploaded by

Copyright:

Available Formats

What are the differences between Combinational Circuits and Sequential Circuits?

Define Rise Time?

Digital Electronics Interview Questions

Ques1: What are the applications of Demultiplexer?

Combinational Circuits Sequential Circuits

Ques3: Define Rise Time?

Downloaded From- RecruitmentResult.com Page 1

Ques8: What are the applications of Demultiplexer?

Downloaded From- RecruitmentResult.com Page 2

Ques14: What are the limitations of the Karnaugh Map?

Ques15: What are the applications of Multiplexer (MUX)?

Downloaded From- RecruitmentResult.com Page 3

You might also like