SERIAL PIC PROGRAMMER C021 CTS

DTR
Serial PIC Programmer kit is a must have for all those who develop, experiment, program and CN1
DB-9 FEMALE R1 1.5K
play with Microchip based PIC projects. 1 C-GND Q1
6 BC547
¦ JDM compatible interface design 2 R2 10K
+
¦ ICSP and direct chip level programming available 7 RTS
ZD1 C1

PGD
3 TXD
¦ ZIF type socket for easy placement and removal of the microcontroller 8 CTS D1 5.1V 100uF/25V
4 1N4148
¦ LED indication of programming being done 9
DTR

¦ No power supply needed. May not work on laptops where the voltage may be below 7.3 V 5 C-GND
PGC
¦ Zener Diode protected design RTS

¦ 9-Pin PCB mounted female type D connector provided for PC side connection VDD
D2
¦ Selector switch for selecting different PIC type during programming in ZIF socket 1N4148 CN2
¦ Marker points provided on PCB for proper insertion point of different PIC's in the ZIF socket SW1
SW ITCH 28-40 PIN
ZIFSOC-20x2

¦ Four mounting holes of 3.2 mm each MCLR 1

2
40
39
CN3 8-18 PIN
¦ PCB dimensions 53 mm x 108 mm PIC ICSP 3 38
MCLR R4 4 37
MCLR 1 5 36
D3 ZD2 R3 100
PGC 1N4148 6.2V 1K 6 35

PGM
PGC 2 7 34
PGD 8 33
PGD 3 9 32
TXD Q2 R5 10K
BC547 10 31
GND 4 11 30
D4
PGM LED 12 29
PGM 5 13 28
Q3
VDD D5 BC557 14 27
VDD 6 15 26
1N4148
C3 16 25
+ 0.1uF 17 24
C2 18 23
100uF/25V SW2 19 22
SW 20 21
R6 J1
10K JUMPER

SR. QTY. REF. DESC RIPTION

This is a Multichip PIC programmer using serial port. The programmer is a JDM Clone, 1 1 C N1 9 PIN D C ONNEC TOR - FEMALE
named after its Original developer Jens Dyekjar Madsen who devised this first. The 2 1 C N2 40 PIN ZIF SOC KET
Programmer can program 8-pin to 40-pin devices using single ZIF socket as well as 3 1 C N3 6 PIN RELIMATE/BERG C ONNEC TOR
ICSP cable. ICSP option is available at Connector CN3 which is clearly marked for pin 4 2 C 1,C 2 100uF/25V
description. LED D4 Provides visual indication of programming taking place. This 5 1 C3 0.1uF
Programmer does not need any power supply. SW1 is a switch select for programming 6 4 D1,D2,D3,D5 1N4148
40-28 and 18-8 PIC Micros in the ZIF socket. Since the programming voltage is taken 7 1 D4 RED LED
from the Serial Port of the Computer, it is recommended you check this voltage before 8 1 J1 2 PIN JUMPER WITH C LOSER
using it. Voltage at TxD, DTR and RTS should be ± 7.5V and above. Insertion position 9 2 Q1,Q2 BC 547
of different PIC are clearly marked on the PCB if you wish to use the ZIF socket for 10 1 Q3 BC 557
programming. SW2 on the PCB selects the “VPP before VDD” option available for 11 1 R1 1.5K
certain PIC micros with Internal OSC and MCLR chosen. Please check the datasheet of 12 3 R2,R5,R6 10K
the respective PIC you choose to program for this feature. Some popular 13 1 R3 1K
programming software used along with this programmer are IC-Prog of Bonny Gijzen 14 1 R4 100E
and WinPic800 available at http://www.winpic800.com. These are freely 15 1 SW1 3 PIN SLIDE SWITC H
downloadable from the net. 16 1 SW2 3 PIN BERG JUMPER WITH C LOSER
17 1 ZD1 5.1V ZENER
Please refer to the schematic diagram for the configuration of this board. 18 1 ZD2 6.2V ZENER
19 9 JUMPER WIRE JUMPER
The kit includes all components required for the project accepts power supply, cabinet
and Serial Port cable. Please check the components supplied to you as per the BOM
“Bill of Material” listed in this document.

Copyright © 2005
www.beta-layout.de