Turnbuckle.

fm Page 25 Thursday, February 2, 2006 8:42 AM

Crosby® Turnbuckles

HG-223 HG-225 HG-226 HG-227 HG-228

Hook & Hook Hook & Eye Eye & Eye Jaw & Eye Jaw & Jaw
Meets the performance Meets the performance Meets the performance Meets the performance Meets the performance
requirements of Federal requirements of Federal requirements of Federal requirements of Federal requirements of Federal
Specifications FF-T-791b, Specifications FF-T-791b, Specifications FF-T-791b, Specifications FF-T-791b, Specifications FF-T-791b,
Type 1, Form 1 — Class Type 1, Form 1 — Class Type 1, Form 1 — Class Type 1, Form 1 — Class Type 1, Form 1 — Class
5, and ASTM F-1145, 6, and ASTM F-1145, 4, and ASTM F-1145, 8, and ASTM F-1145, 7, and ASTM F-1145,
except for those provi- except for those provi- except for those provi- except for those provi- except for those provi-
sions required of the sions required of the sions required of the sions required of the sions required of the
contractor. contractor. contractor contractor. contractor.

• Turnbuckle assembly combinations include: Eye and Eye, Hook and Hook,
Hook and Eye, Jaw and Jaw & Jaw and Eye.
• End fittings are Quenched and Tempered, bodies heat treated by normalizing.
• Crosby’s Quenched and Tempered end fittings and normalized bodies
have enhanced impact properties for greater toughness at all temperatures.
• Hot Dip galvanized. Modified thread:
• Hooks are forged with a greater cross sectional area that results in a stronger Note stress
hook with better fatigue properties. relieving radii
• Modified UNJ thread on end fittings for improved fatigue properties. Body in this unretouched
has UNC threads. photo enlargement
of the supabuckle.
• Turnbuckle eyes are forged elongated, by design, to maximize easy attach-
ment in system and minimize stress in the eye. For turnbuckle sizes 6.35mm
through 63.5mm, a shackle one size smaller can be reeved through eye.
• Forged jaw ends are fitted with bolts and nuts on sizes 6.35mm - 15.9mm,
and pins and cotters on sizes19.1mm - 70.0mm.
• TURNBUCKLES RECOMMENDED FOR STRAIGHT OR IN-LINE PULL
ONLY.
• Lock Nuts available for all sizes.
• Typical hardness levels, Tensile Strengths and Ductility Properties are Standard thread:
available for all sizes. Note stress
• Turnbuckles can be furnished proof tested or magnaflux inspected with building sharp “V”
certificates if requested at time of order. in this unretouched
• Crosby products meet or exceed all the requirements of ASME B30.26 photo enlargement.
including identification, ductility, design factor, proof load and temperature
requirements. Importantly, Crosby products meet other critical performance
requirements including fatigue life, impact properties and material tracea-
bility, not addressed by ASME B30.26.

154 Copyright © 2006 The Crosby Group, Inc.

All Rights Reserved
 Hook & Hook Turnbuckles

HG-223 • End fittings are Quenched and Tempered, bodies heat treated by normalizing.
• Hot Dip galvanized steel.
• Hooks are forged with a greater cross sectional area that results in a stronger hook
with better fatigue properties.
• Crosby products meet or exceed all requirements of ASME B30.26 including identification,
ductility, design factor, proof load and temperature requirements. Importantly, Crosby
products meet other critical performance requirements including fatigue life, impact
properties and material traceability, not addressed by ASME B30.26.
• TURNBUCKLES RECOMMENDED FOR STRAIGHT OR IN-LINE PULL ONLY.
• Modified UNJ thread on end fittings for improved fatigue properties.
• Body has UNC threads.
• Lock Nuts available for all sizes (see page 164).
• Comprehensive end fitting data provided on page 160.
• Fatigue Rated.
s e l k c u b n r u T k o o H & k o o H

Accessories
Rigging
Meets the performance requirements of Federal
Specifications FF-T-791b, Type 1 Form 1 - CLASS
5,and ASTM F-1145, except for those provisions
required of the contractor. For additional infor-
mation, see page 361.

HG-223
Hook & Hook
Thread Working Dimensions
Diameter HG2 3 Load Weight (mm)
& Take Up HG-223 Limit Each E J K M N
(mm) Stock No. (t)* (kg) A D Closed F Open Closed Open Closed BB
6.35 x 102 1030011 .18 .14 6.35 11.4 40.4 32.3 282 181 303 202 101
7.94 x 114 1030039 .32 .21 7.85 12.7 49.3 38.1 325 211 351 236 114
9.53 x 152 1030057 .45 .35 9.65 14.2 58.5 45.0 419 267 450 298 152
12.7 x 152 1030075 .68 .73 12.7 16.8 74.5 58.0 478 300 518 340 152
12.7 x 305 1030119 .68 1.03 12.7 16.8 74.5 58.0 783 453 822 492 304
15.9 x 305 1030137 1.02 1.25 16.0 22.9 93.5 71.5 521 337 572 387 152
15.9 x 305 1030173 1.02 1.59 16.0 22.9 93.5 71.5 826 489 876 540 304
19.1 x 152 1030191 1.36 1.76 19.1 24.9 115 84.5 568 378 629 439 152
19.1 x 305 1030235 1.36 2.46 19.1 24.9 115 84.5 873 530 934 591 304
19.1 x 457 1030253 1.36 3.68 19.1 24.9 115 84.5 1178 683 1239 744 457
22.2 x 305 1030271 1.81 3.67 22.4 28.7 132 96.0 914 565 984 635 304
25.4 x 305 1030333 2.27 5.41 25.4 31.8 148 108 956 600 1034 678 304
* Proof Load is 2.5 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit.

Copyright © 2006 The Crosby Group, Inc. 155

All Rights Reserved
 Hook & Eye Turnbuckles

HG-225 • End fittings are Quenched and Tempered, bodies heat treated by normalizing.
• Hot Dip galvanized steel.
• Turnbuckle eyes are forged elongated, by design, to maximize easy attachment in system
and minimize stress in the eye. For turnbuckles sizes 6 mm through 64 mm, a shackle one
size smaller can be reeved through eye.
• Turnbuckle hooks are forged with a greater cross sectional area that results in a stronger
hook with better fatigue properties.
• Crosby products meet or exceed all requirements of ASME B30.26 including identification,
ductility, design factor, proof load and temperature requirements. Importantly, Crosby
products meet other critical performance requirements including fatigue life, impact
properties and material traceability, not addressed by ASME B30.26.
• TURNBUCKLES RECOMMENDED FOR STRAIGHT OR IN-LINE PULL ONLY.
• Modified UNJ thread on end fittings for improved fatigue properties.
• Body has UNC threads.
• Lock Nuts available for all sizes (see page 164).
• Comprehensive end fitting data provided on pages 160 & 161.
• Fatigue Rated.
s e l k c u b n r u T e y E & k o o H

Meets the performance requirements of Federal

Specifications FF-T-791b, Type 1, Form 1 — CLASS
6,and ASTM F-1145, except for those provisions
required of the contractor. For additional infor-
mation, see page 361.

HG-225
Hook & Eye
Thread HG2 5 Working Dimensions
Diameter HG-225 Load Weight (mm)
& Take Up Stock Limit Each E J K M N X
(mm) No. (t)* (kg) A D Closed F Open Closed Open Closed R S Closed BB
6.35 x 102 1030636 .18 .13 6.35 11.4 40.4 32.3 291 189 307 205 19.8 8.64 44.5 102
7.94 x 114 1030654 .32 .22 7.94 12.7 49.3 38.1 335 221 342 241 23.9 11.2 53.0 114
9.53 x 152 1030672 .45 .35 9.53 14.2 58.0 45.0 431 279 456 303 28.5 13.5 64.0 152
12.7 x 152 1030690 .68 .73 12.7 16.8 74.5 58.0 494 316 525 347 36.6 18.3 82.0 152
12.7 x 305 1030734 .68 1.03 12.7 16.8 74.5 58.0 798 469 829 500 36.6 18.3 82.0 305
15.9 x 152 1030752 1.02 1.22 15.9 21.3 93.5 71.0 557 355 577 393 44.5 22.2 99.0 152
15.9 x 305 1030798 1.02 1.71 15.9 21.3 93.5 71.0 844 507 882 545 44.5 22.2 99.0 305
19.1 x 152 1030814 1.36 1.76 19.1 24.9 115 85.0 587 397 634 443 53.0 25.4 119 152
19.1 x 305 1030850 1.36 2.64 19.1 24.9 115 84.5 892 549 939 596 53.0 25.4 119 305
19.1 x 457 1030878 1.36 2.87 19.1 24.9 115 84.5 1197 702 1243 748 53.0 25.4 119 457
22.2 x 305 1030896 1.81 3.67 22.2 28.7 132 96.0 927 579 982 633 60.0 31.8 130 305
25.4 x 305 1030958 2.27 5.41 25.4 31.8 148 108 985 630 1046 691 76.0 36.6 162 305
* Proof Load is 2.5 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit.

156 Copyright © 2006 The Crosby Group, Inc.

All Rights Reserved
 Eye & Eye Turnbuckles

HG-226 • End fittings are Quenched and Tempered, bodies heat treated by normalizing.
• Hot Dip galvanized steel.
• Turnbuckle eyes are forged elongated, by design, to maximize easy attachment in system
and minimize stress in the eye. For turnbuckle sizes 6 mm through 64 mm, a shackle one
size smaller can be reeved through eye.
• Modified UNJ thread on end fittings for improved fatigue properties. Body has UNC
threads.
• Crosby products meet or exceed all requirements of ASME B30.26 including identification,
ductility, design factor, proof load and temperature requirements. Importantly, Crosby
products meet other critical performance requirements including fatigue life, impact
properties and material traceability, not addressed by ASME B30.26.
• TURNBUCKLES RECOMMENDED FOR STRAIGHT OR IN-LINE PULL ONLY.
• Lock Nuts available for all sizes (see page 164).
• Comprehensive end fitting data provided on page 161.
• Fatigue Rated.
s e l k c u b n r u T e y E & e y E

Accessories
Meets the performance requirements of Federal

Rigging
Specifications FF-T-791b, Type 1, Form 1 - CLASS
4,and ASTM F-1145, except for those provisions
required of the contractor. For additional infor-
mation, see page 361.

HG-226
Eye & Eye
Thread Working Dimensions
Diameter HG2 6 Load Weight (mm)
& Take Up HG-226 Limit Each J K M N X
(mm) Stock No. (t)* (kg) A Open Closed Open Closed R S Closed BB
6.35 x 102 1031252 .23 .12 6.35 300 198 311 210 19.8 8.65 44.5 101
7.94 x 114 1031270 .36 .20 7.85 344 230 359 244 23.8 11.1 53.0 114
9.53 x 152 1031298 .54 .34 9.65 444 291 461 309 28.4 13.4 64.0 152
12.7 x 152 1031314 1.00 .70 12.7 510 332 532 355 36.5 18.2 82.0 152
12.7 x 305 1031350 1.00 .97 12.7 815 485 837 507 36.5 18.2 82.0 304
15.9 x 152 1031378 1.59 1.09 16.0 557 373 582 398 44.4 22.3 99.0 152
15.9 x 305 1031412 1.59 1.55 16.0 862 525 887 551 44.4 22.3 99.0 304
19.1 x 152 1031430 2.36 1.72 19.1 607 416 638 448 53.0 25.4 119 152
19.1 x 305 1031476 2.36 2.49 19.1 911 568 943 600 53.0 25.4 119 304
19.1 x 457 1031494 2.36 3.26 19.1 1216 721 1248 752 53.0 25.4 119 457
22.2 x 305 1031519 3.27 3.27 22.4 942 592 980 630 60.4 31.7 130 304
22.2 x 457 1031537 3.27 4.51 22.4 1246 745 1284 783 60.4 31.7 130 457
25.4 x 152 1031555 4.54 4.10 25.4 710 507 755 552 76.0 36.5 162 152
25.4 x 305 1031573 4.54 5.22 25.4 1015 660 1066 704 76.0 36.5 162 304
25.4 x 457 1031591 4.54 6.35 25.4 1320 812 1364 856 76.0 36.5 162 457
25.4 x 610 1031617 4.54 7.82 25.4 1625 964 1669 1009 76.0 36.5 162 609
31.8 x 305 1031635 6.89 8.62 31.8 1087 719 1145 776 90.5 46.0 196 304
31.8 x 457 1031653 6.89 10.4 31.8 1392 871 1449 929 90.5 46.0 196 457
31.8 x 610 1031671 6.89 12.2 31.8 1697 1024 1754 1081 90.5 46.0 196 609
38.1 x 305 1031699 9.71 12.5 38.1 1156 775 1219 838 103 54.0 219 304
38.1 x 457 1031715 9.71 14.1 38.1 1461 927 1524 991 103 54.0 219 457
38.1 x 610 1031733 9.71 17.0 38.1 1765 1080 1829 1143 103 54.0 219 609
44.5 x 457 1031779 12.7 23.8 44.5 1457 1000 1534 1076 117 60.4 254 457
44.5 x 610 1031797 12.7 26.3 44.5 1762 1153 1838 1229 117 60.4 254 609
51.0 x 610 1031813 16.8 38.7 51.0 1923 1313 2011 1402 146 68.5 333 609
63.5 x 610 1031831 27.2 65 63.5 1997 1387 2099 1489 165 79.0 350 609
70.0 x 610 1031859 34.0 88 70.0 2057 1448 2172 1562 177 82.5 387 609
* Proof Load is 2.5 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit.

Copyright © 2006 The Crosby Group, Inc. 157

All Rights Reserved
 Jaw & Eye Turnbuckles

HG-227 • End fittings are Quenched and Tempered, bodies heat treated by normalizing.
• Hot Dip galvanized steel.
• Turnbuckles eyes are forged and elongated, by design, to maximize easy attachment in
system and minimize stress in the eye. For turnbuckles size 6 mm through 64 mm, a
shackle one size smaller can be reeved through eye.
• Forged jaw ends are fitted with bolts and nuts for 6mm through 16mm, and pins and
cotters on 19 mm through 70 mm sizes.
• Modified UNJ thread on end fittings for improved fatigue properties.
• Body has UNC threads.
• Crosby products meet or exceed all requirements of ASME B30.26 including identification,
ductility, design factor, proof load and temperature requirements. Importantly, Crosby
products meet other critical performance requirements including fatigue life, impact
properties and material traceability, not addressed by ASME B30.26.
• TURNBUCKLES RECOMMENDED FOR STRAIGHT OR IN-LINE PULL ONLY.
• Lock Nuts available for all sizes (see page 164).
• Comprehensive End fitting data on pages 161 & 162.
• Fatigue Rated.
s e l k c u b n r u T e y E & w a J

Meets the performance requirements of Federal

Specifications FF-T-791b, Type 1, Form 1 - CLASS
8,and ASTM F-1145, except for those provisions
required of the contractor. For additional infor-
mation, see page 361.

HG-227
Jaw & Eye
Thread Working Dimensions
Diameter HG2 7 Load Weight (mm)
& Take Up HG-227 Limit Each E J K M N X
(mm) Stock No. (t)* (kg) A B Closed G Open Closed Open Closed R S Closed BB
6.35 x 102 1031877 .23 .14 6.35 11.4 40.1 15.7 288 187 307 205 19.8 8.65 44.5 101
7.94 x 114 1031895 .36 .23 7.85 12.7 50.5 22.1 348 221 356 242 23.8 11.1 53.0 114
9.53 x 152 1031911 .54 .36 9.65 13.7 54.0 22.1 427 275 451 299 28.4 13.4 64.0 152
12.7 x 152 1031939 1.00 .68 12.7 16.5 70.0 26.9 490 312 520 342 36.5 18.2 82.0 152
12.7 x 229 1031957 1.00 .78 12.7 16.5 70.0 26.9 642 388 673 419 36.5 18.2 82.0 228
12.7 x 305 1031975 1.00 .94 12.7 16.5 70.0 26.9 795 465 825 495 36.5 18.2 82.0 304
15.9 x 305 1031993 1.59 1.07 16.0 20.1 89.0 33.3 533 349 572 388 44.4 22.3 99.0 152
15.9 x 229 1032019 1.59 1.44 16.0 20.1 89.0 33.3 686 425 725 464 44.4 22.3 99.0 228
15.9 x 305 1032037 1.59 1.64 16.0 20.1 89.0 33.3 838 501 877 541 44.4 22.3 99.0 304
19.1 x 152 1032055 2.36 1.81 19.1 23.9 106 38.1 576 386 625 435 53.0 25.4 119 152
19.1 x 229 1032073 2.36 2.15 19.1 23.9 106 38.1 729 462 777 511 53.0 25.4 119 228
19.1 x 305 1032091 2.36 2.69 19.1 23.9 106 38.1 881 538 930 587 53.0 25.4 119 304
19.1 x 457 1032117 2.36 3.18 19.1 23.9 106 38.1 1186 691 1235 739 53.0 25.4 119 457
22.2 x 305 1032135 3.27 3.79 22.4 28.7 123 44.5 917 567 973 624 60.4 31.7 130 304
22.2 x 457 1032153 3.27 4.42 22.4 28.7 123 44.5 1221 720 1278 776 60.4 31.7 130 457
25.4 x 152 1032171 4.54 4.05 25.4 34.0 140 52.5 669 466 734 531 76.0 36.5 162 152
25.4 x 305 1032199 4.54 5.08 25.4 34.0 140 52.5 974 618 1039 683 76.0 36.5 162 304
25.4 x 457 1032215 4.54 6.03 25.4 34.0 140 52.5 1279 771 1343 835 76.0 36.5 162 457
25.4 x 610 1032233 4.54 7.71 25.4 34.0 140 52.5 1583 923 1648 988 76.0 36.5 162 609
31.8 x 305 1032251 6.89 8.81 31.8 44.5 183 71.5 1050 681 1132 763 90.5 46.0 196 304
31.8 x 457 1032279 6.89 11.0 31.8 44.5 183 71.5 1354 834 1424 916 90.5 46.0 196 457
31.8 x 610 1032297 6.89 12.9 31.8 44.5 183 71.5 1659 986 1741 1068 90.5 46.0 196 609
38.1 x 305 1032313 9.71 13.1 38.1 52.3 200 71.5 1105 724 1200 819 103 54.0 219 304
38.1 x 457 1032331 9.71 15.9 38.1 52.3 200 71.5 1410 876 1505 972 103 54.0 219 457
38.1 x 610 1032359 9.71 17.8 38.1 52.3 200 71.5 1715 1029 1810 1124 103 54.0 219 609
44.5 x 457 1032395 12.7 24.4 44.5 66.0 239 86.0 1407 949 1518 1061 117 60.4 254 457
44.5 x 610 1032411 12.7 27.5 44.5 66.0 239 86.0 1711 1102 1823 1214 117 60.4 254 609
51.0 x 610 1032439 16.8 40.4 51.0 66.5 301 93.5 1845 1235 1980 1370 146 68.3 332 609
63.5 x 610 1032457 27.2 68 63.5 76.5 344 113 1925 1316 2093 1483 165 79.0 350 609
70.0 x 610 1032475 34.0 83 70.0 92.2 387 106 1978 1369 2172 1562 177 82.5 387 609
* Proof Load is 2.5 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit.
158 Copyright © 2006 The Crosby Group, Inc.
All Rights Reserved
 Jaw & Jaw Turnbuckles

HG-228 • End fittings are Quenched and Tempered, bodies heat treated by normalizing.
• Hot Dip galvanized steel.
• TURNBUCKLES RECOMMENDED FOR STRAIGHT OR IN-LINE PULL ONLY.
• Forged jaw ends are fitted with bolts and nuts for 6 mm through 16 mm, and pins and
cotters on 19 mm through 70 mm sizes.
• Modified UNJ thread on end fittings for improved fatigue properties.
• Body has UNC threads.
• Crosby products meet or exceed all requirements of ASME B30.26 including identification,
ductility, design factor, proof load and temperature requirements. Importantly, Crosby
products meet other critical performance requirements including fatigue life, impact
properties and material traceability, not addressed by ASME B30.26.
• Lock Nuts available for all sizes (see page 164).
• Comprehensive end fitting data provided on page 162.
• Fatigue Rated.
s e l k c u b n r u T w a J & w a J

Accessories
Rigging
Meets the performance requirements of Federal
Specifications FF-T-791b,Type 1, Form 1 - CLASS
7,and ASTM F-1145, except for those provisions
required of the contractor. For additional infor-
mation, see page 361.

HG-228
Jaw & Jaw
Thread Working Dimensions
Diameter HG2 8 Load Weight (mm)
& Take Up HG-228 Limit Each E J K M N
(mm) Stock No. (t)* (kg) A B Closed G Open Closed Open Closed BB
6.35 x 102 1032493 .23 .16 6.35 11.4 40.1 15.7 277 175 302 201 102
7.94 x 114 1032518 .36 .24 7.85 12.7 50.5 22.1 314 212 353 239 114
9.53 x 152 1032536 .54 .37 9.65 13.7 54.0 22.1 410 258 441 289 152
12.7 x 152 1032554 1.00 .71 12.7 16.5 70.0 26.9 470 292 508 330 152
12.7 x 229 1032572 1.00 .79 12.7 16.5 70.0 26.9 622 368 660 406 229
12.7 x 305 1032590 1.00 1.09 12.7 16.5 70.0 26.9 775 445 813 483 305
15.9 x 152 1032616 1.59 1.23 16.0 20.1 89.0 33.3 509 325 562 378 152
15.9 x 229 1032634 1.59 1.56 16.0 20.1 89.0 33.3 662 401 715 454 229
15.9 x 305 1032652 1.59 1.77 16.0 20.1 89.0 33.3 814 478 867 530 305
19.1 x 152 1032670 2.36 1.86 19.1 23.9 106 38.1 546 356 612 422 152
19.1 x 229 1032698 2.36 2.48 19.1 23.9 106 38.1 699 432 765 498 229
19.1 x 305 1032714 2.36 2.98 19.1 23.9 106 38.1 851 508 917 574 305
19.1 x 457 1032732 2.36 3.64 19.1 23.9 106 38.1 1156 660 1222 726 457
22.2 x 305 1032750 3.27 3.71 22.4 28.7 123 44.5 892 543 967 618 305
22.2 x 457 1032778 3.27 4.89 22.4 28.7 123 44.5 1197 695 1272 770 457
25.4 x 152 1032796 4.54 4.62 25.4 34.0 140 52.5 628 425 713 510 152
25.4 x 305 1032812 4.54 5.96 25.4 34.0 140 52.5 933 577 1018 662 305
25.4 x 457 1032830 4.54 6.87 25.4 34.0 140 52.5 1237 729 1322 814 457
25.4 x 610 1032858 4.54 8.20 25.4 34.0 140 52.5 1542 882 1627 967 610
31.8 x 305 1032876 6.89 9.34 31.8 44.5 183 71.5 1012 644 1119 750 305
31.8 x 457 1032894 6.89 11.2 31.8 44.5 183 71.5 1317 796 1423 903 457
31.8 x 610 1032910 6.89 12.8 31.8 44.5 183 71.5 1622 948 1728 1055 610
38.1 x 305 1032938 9.71 13.9 38.1 52.3 200 71.5 1054 673 1181 800 305
38.1 x 457 1032956 9.71 16.7 38.1 52.3 200 71.5 1359 826 1486 953 457
38.1 x 610 1032974 9.71 18.9 38.1 52.3 200 71.5 1664 978 1791 1105 610
44.5 x 457 1033018 12.7 24.5 44.5 66.0 239 86.0 1356 899 1503 1046 457
44.5 x 610 1033036 12.7 28.7 44.5 66.0 239 86.0 1661 1051 1808 1198 610
51.0 x 610 1033054 16.8 42.8 51.0 66.5 301 93.5 1766 1157 1949 1339 610
63.5 x 610 1033072 27.2 75 63.5 76.5 344 113 1854 1244 2087 1478 610
70.0 x 610 1033090 34.0 90 70.0 92.2 387 106 1899 1289 2172 1562 610
* Proof Load is 2.5 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit.

Copyright © 2006 The Crosby Group, Inc. 159

All Rights Reserved