LC161076 MTKF 1 12 0001 PDF

`
Contract No : LC16107600
PROJECT TITLE:-
EPIC OF WALKOVER BRIDGES IN TANK-FARM AREA,

REFINERY, MESAIEED
PROJECT NO: LC161076

DOCUMENT TITLE:
DESIGN CALCULATION REPORT FOR WALKOVER BRIDGE TYPE – 1
(WB1 & WB20)
DESIGN CONSULTANT: MAIN CONTRACTOR:
A 10/07/2017 APPROVED FOR CONSTRUCTION DJ DS RH

2 04/07/2017 RE-ISSUED FOR APPROVAL DJ DS RH
1 12/06/2017 ISSUED FOR APPROVAL DJ DS RH
0 01/06/2017 ISSUED FOR COMMENTS DJ DS RH
Prepared Checked Approved Approved

Rev Date Description
by by by by QP
Document No. LC161076-MTKF-1-12-0001 of Rev. A
01 36
2
DESIGN CALCULATION REPORT FOR
WALKOVER BRIDGE TYPE – 1 (WB1 & WB20)
CONTENTS Page
DEFINITIONS .......................................................................................... 3
ABBREVIATION ...................................................................................... 4
1 INTRODUCTION ........................................................................... 5
2 BASIC DATA ................................................................................ 5

2.1 UNITS OF MEASUREMENT .......................................................................... 5
3 REFERENCE DOCUMENTS ........................................................ 5

3.1 QP STANDARDS/SPECIFICATIONS: ........................................................... 5
3.2 INTERNATIONAL CODES & STANDARDS.................................................. 6
3.3 MATERIALS................................................................................................... 7
4 LOADS.......................................................................................... 7
4.1 DEAD LOADS (DL) ........................................................................................ 7
4.2 LIVE LOADS (LL) .......................................................................................... 9
4.3 WIND LOADS (WL) ....................................................................................... 9
5 LOAD COMBINATIONS ............................................................. 11
6 ANALYSIS & DESIGN ................................................................ 11

6.1 STAAD MODEL ........................................................................................... 12
6.2 DEFLECTION CHECK ................................................................................. 20
6.3 UTILIZATION RATIO OF THE MEMBER .................................................... 22
7 CONNECTION DESIGN ............................................................. 22

7.1 Connection design for main beam & column........................................... 22
7.2 Connection design for stringer beam & main beam ................................ 24
8 BASE PLATE & ANCHOR BOLT DESIGN................................ 25

8.1 Base Plate & Anchor Bolts Design For CH150x75X18 Columns ............ 25
8.2 Base Plate & Anchor Bolts Design For CH150x75X18 Columns ............ 28
9 FOUNDATION DESIGN ............................................................. 29

9.1 FOUNDATION DESIGN FOR SRTINGER & COLUMN ............................... 30
ATTACHMENT - A ................................................................................ 36
Doc No: LC161076-MTKF-1-12-0001 Rev.A Page 2 of 36

DEFINITIONS
For the purposes of this report, the following definitions of terms and interpretations
shall apply regardless of and other meaning the words may have in other respects:
Shall The word "shall" is to be understood as mandatory.
Should The word "should" is to be understood as being

strongly
Recommended
May The word "may" is used where alternatives are equally

acceptable
Must The word "must" is used where a provision is a

statutory
Requirement
Client / Company Qatar Petroleum
Contractor Company / Firm or Party appointed by QP to perform

the works in accordance with this specification
Manufacturer The Party that manufactures, fabricates or produces

materials or products covered by this specification
Supplier Company / Firm or Party appointed by QP to supply

material, equipment or other products in accordance
with this specification

ABBREVIATION
DBM - Design Basis Memorandum
EPIC - Engineering, Procurement, Installation and Commissioning
MIC - Mesaieed Industrial City
QP - Qatar Petroleum
QCS - Qatar Construction Standards
BS - British Standards
BS EN - British Standards European Norms
AWS - American Welding Society
SI - System International d’Unites, International Metric System
SOW - Scope of Work
WB - Walkover Bridge

1 INTRODUCTION
This document has been prepared by Qatar Design Consortium for AL-BALAGH
and Qatar Petroleum. It constitutes the part of “Steel Walkover Platforms/Bridges in
Tank-Farm area at QP Refinery.
The document presents the design calculations for Type-1 walk over bridges (WB1,
WB20) superstructure & foundation.
2 BASIC DATA
2.1 UNITS OF MEASUREMENT
In general, SI units shall be used within this project. Most commonly used units of
measurements for this project are specified below:
Quantity Unit Nomenclature

Length Meter m
Area Square meter m2
Volume Cubic meter m3
Mass Kilogram(gram) / Ton kg(g) / T
Diameter millimetre mm
Pressure, Stress Pascal Pa
3 REFERENCE DOCUMENTS
Reference has also been made in this specification to the latest edition of the
following codes standards and specifications.
3.1 QP STANDARDS/SPECIFICATIONS:
ES.0.01.0015 AutoCAD Standard
ES-D-10 Engineering Standard – Drafting
QP-SPC-L-002 Painting and Wrapping of Metal surfaces
Quality Requirements for Procurements for Materials
QP-STD-Q-003
and Equipment
QP-STD-Q-004 Quality Requirements for Projects
ES.0.06.0021 Compilation of Project Dossiers
Engineering Data Coding System for Project and “As-
ES.0.07.0014 Built”
Core Data
7J48N-00-00-33-005 Project Design Basis
7J48N-00-14-17-001 Design Criteria for Civil and Structure
7J48N-00-69-00-136 Construction Procedure for Concrete
7J48N-00-69-00-152 Construction Procedure for Structural Steel Work

RP.5914.D.00.1400.02 Soil and Foundations

RP.5914.D.00.1400.03 Earthworks
RP.5914.D.00.1700.01 Concrete Works Design
RP.5914.D.00.1800.01 Design and Construction of Steel Structures
3.2 INTERNATIONAL CODES & STANDARDS

AWS D1.1 Structural Welding Code
BCSA guidelines National Structural Steelwork Specification (British

Construction Steel Association Guidelines)
BS 4-1 Structural steel sections – Specifications for Hot rolled
sections.
BS 3692 Specification for ISO metric precision hexagon bolts,
screws and nuts. Metric units.
BS 4190 ISO Metric Black Hexagon Bolts, Screws and Nuts
BS 4320 Metal Washers for General Engineering Purposes
BS 5950 Structural use of Steelwork in Building
BS 8110 Design and Construction of Reinforced concrete

Structure
BS 4592 Parts I to V Industrial type metal floorings. Walkways and stair
treads.
BS EN 1990 Basis of Structural Design
BS EN 1991 Euro code 1 – Action on Structures
BS EN 1992-1-1 Euro code 2-Design of concrete structures.
BS EN 1993-1-1 Design of steel structures
BS EN ISO 5395-3 Stairs, Ladders And Walkways
BS 4027 Specification for sulphate-resisting Portland cement
BS 6399-2 Code of practice for wind loads
BS EN 197 (All parts) Cement. Composition, specifications and conformity

criteria for common cements
BS 4449 Specification for carbon steel bars for the reinforcement
of concrete
BS 4466 Scheduling, dimensioning, bending and cutting of steel

reinforcement for concrete
BS 8004 Code of practice for foundations
BS 4482 Specification for steel wire for the reinforcement of
concrete products
BS 4483 Specification for steel fabric for the reinforcement of

concrete

BS 5395 Parts 1 to 3 Stairs, ladders and walkways

BS EN 287
Approval testing of welders for fusion welding
BS EN 288 Specification and approval of welding procedures for
metallic materials
Welding consumables-Wire electrodes and weld
BS EN 440 deposits for gas shielded metal arc welding of non-alloy
and fine grain steels. Classification
Welding consumables-Covered electrodes for manual
BS EN 499 metal arc welding of non-alloy and fine grain steels.
Classification
BS EN 1011 Welding Recommendations for Welding of Metallic
Materials
Hot finished structural hollow sections of non-alloy and
BS EN 10210 fine grain structural steels – tolerances, dimensions and
sectional properties
BS EN ISO 1461 Hot dip galvanized coatings on fabricated iron and steel
articles
3.3 MATERIALS
3.3.1 GRADE OF CONCRETE

Grade of concrete - C40
3.3.2 CONCRETE REINFORCEMENT STEEL

Reinforcing steel shall be uncoated high yield deformed bars of minimum strength of
500 N/mm2
3.3.3 STRUCTURAL STEEL

All structural steel shall be of Grade S275
4 LOADS
The following loads shall be considered for the design of steel platform:
a) Dead load
b) Live load
c) Wind load
4.1 DEAD LOADS (DL)

All permanent structural elements forming part of the structure shall be considered as
dead loads. The design dead loads shall be calculated in accordance with the unit
weights of materials and components as defined in BS-4 ‘Structural steel sections –
Specifications for Hot rolled sections’.

Following Unit weights have been considered in calculating self-weight of structure.
Structural Steel = 78.5 kN/m3
Reinforced Concrete = 25 kN/m3 (for substructure design)
Soil = 18 kN/m3 (for substructure design)
The components contributing to the dead load are self-weight of the structural
members, grating and handrails.
Self-weight of the structure has been automatically considered in the analysis by the
software (STAAD.pro)
Grating load considered = 38.5 kg/m2 = 0.385 kN/m2 (applied as per one way
distributions)
A sample calculation has been shown below for estimating the grating load on
supporting beams. The grating load on the entire structure has been calculated in the
same manner.
Self-weight of 30 mm thick grating = 0.385 kN/m2
Platform Width =1m
Width of grating supported on each side of beam = 1/2 = 0.5 m
Load on beam due to grating (half width) = 0.5 x 0.385
= 0.2 kN/m
Size of one stair tread = 1 m x0.25 m
Steps Load due to grating = 1.0 x 0.25 x 0.385
= 0.1 kN
No. of support point =2
Load on each support point = 0.1 / 2

= 0.05 kN
Weight of Handrail = 5.34 kg\m = 0.0534 kN/m
Weight of vertical leg = 6.4Kg/m = 0.064 kN/m
Weight of mid rail = 4.6Kg/m = 0.046 kN/m

Maximum spacing of vertical post considered = 1.2 m
Handrail load (1.2x0.0534)+(1.2 x 0.046)+(1.2x0.064) = 0.2 kN (Support point)
4.2 LIVE LOADS (LL)

Live load intensity = 5 kN/m2
Live load on beam = 0.5 x 5 = 2.5 kN/m
Live Load on steps = 1.0 x 0.25 x 5= 1.25 KN
Point load on each side = 1.25/2 =0.625 KN
4.3 WIND LOADS (WL)

The wind loads shall be calculated in accordance with BS EN 1991-1-4, “Actions on
structures General actions. Wind actions”.
The basic wind speed as per DBM is 27 m/s,
Structure shall be designed for a minimum fundamental basic wind velocity (V b, 0) of

27 m/s; as per QCS.
Refer next page for calculations.


5 LOAD COMBINATIONS
The following load combinations will be considered in the design of Walkover Bridge
and its supports:
SERVICEABILITY CRITERIA
101 1.0DL+1.0LL
102 1.0DL+1.0WL (+X)
103 1.0DL+1.0WL (-X)
104 1.0DL+1.0WL (+Z)
105 1.0DL+1.0WL (-Z)
106 1.0DL+1.0LL+1.0WL (+X)
107 1.0DL+1.0LL+1.0WL (-X)
108 1.0DL+1.0LL+1.0WL (+Z)
109 1.0DL+1.0LL+1.0WL (-Z)
STRENGTH CRITERIA
201 1.35DL+1.5LL
202 1.35DL+1.5WL (+X)
203 1.35DL+1.5WL (-X)
204 1.35DL+1.5WL (+Z)
205 1.35DL+1.5WL (-Z)
206 1.35DL+1.5LL+0.75WL (+X)
207 1.35DL+1.5LL+0.75WL (-X)
208 1.35DL+1.5LL+0.75WL (+Z)
209 1.35DL+1.5LL+0.75WL (-Z)
6 ANALYSIS & DESIGN

The objective of this section is to cover the design of steel walkover WB1 & WB20
Bridges in Tank-Farm area. The walkover bridge WB1 & WB20 are same of size and
configuration, hence considered as type-1.

6.1 STAAD MODEL

The walkover bridge has been modelled in STAAD PRO software to simulate the
actual behaviour of the steel structure and has been designed in accordance with BS
EN 1993-1-1:2005.
3D RENDERED VIEW OF PLATFORM - STAAD MODELLING

NODE NUMBER
SUPPORT DETAILS
NODE NUMBER Fx Fy Fz Mx My Mz
43 FIXED FIXED FIXED FIXED RELEASED RELEASED
SUPPORT DETAILS

BEAM NUMBERS
SECTION PROPERTY FOR MAIN BEAM, TIE BEAM & PLAN BRACE

SECTION PROPERTY FOR STRINGER & COLUMN
SECTION PROPERTY FOR TIE BEAM, COLUMN & VERICAL BRACE

DIMENSION FOR STRINER, MAIN BEAM & COLUMN
BEAM DIMENSION FOR MAIN BEAM &TIE BEAM

DIMENSION FOR TIE BEAM, COLUMN & KNEE
DEAD LOAD

LIVE LOAD
WIND LOAD IN X-DIRECTION

WIND LOAD IN –X-DIRECTION
WIND LOAD IN +Z-DIRECTION

WIND LOAD IN –Z-DIRECTION
6.2 DEFLECTION CHECK

DEFLECTION CRITERIA
Category Member type Allowable Deflection
Walkover Bridge Members Columns H/200 (Horizontal)
Walkover Bridge Members Platform Beams L/360 (Vertical)

6.2.1 COLUMN DEFLECTION CHECK:

Column Deflection Summary:
Following table extracted from STAAD output shows that all the members are within
allowed deflection limits.
Above snapshot shows that
Maximum deflection at column top (max of X & Z) = 1.020 mm
Whereas, the permissible deflection = H/200 = 1600/200 = 8 mm
Hence safe, the deflection is within limits.
6.2.2 BEAM DEFLECTION CHECK:

Beam Deflection Summary:

Maximum vertical deflection (max Y) = 15.685
Whereas, the permissible vertical deflection = H/360 = 6250/ 360 = 17.36 mm
Hence, the vertical deflection beam is within limits.
6.3 UTILIZATION RATIO OF THE MEMBER

The utility ratio of the members is as shown in the figure below.
The maximum utility ratio has been observed to be 0.580 which is less than the
allowable value i.e. 1.0. Hence all the members provided are safe.
7 CONNECTION DESIGN
7.1 Connection design for main beam & column

From the table of maximum section force,

The axial load = 16.890 kN
The horizontal shear =2.296 kN
The vertical shear =0.204 kN
The resultant shear = 2.30kN
Use 4 bolt M16 grade 8.8.
Shear capacity of per bolt is 58.9 kN (Refer below table extracted from SCI-398 )
The connection hence safe.

7.2
.2 Connection design for stringer beam & main beam
From the table of maximum section force,

The axial load =2.64 kN
The vertical shear =3.2 kN
The horizontal shear =0.441kN
The resultant shear =3.2 kN
Use 4 bolt M16 grade 8.8.
Shear capacity of per bolt is 58.9 kN (Refer below table extracted from SCI 398)
The connection is hence safe.

8 BASE PLATE & ANCHOR BOLT DESIGN

8.1 Base Plate & Anchor Bolts Design For CH150x75X18 Columns
(For Supports CH 150x75X18 to STAAD support node nos are given below.)
The base plate design is done for maximum forces.



8.2 Base Plate & Anchor Bolts Design For CH150x75X18 Columns
(For Supports CH 150x75X18 to STAAD support node nos are given below)

The base plate design is done for maximum force
There is no tension & maximum shear is 7.41 kN & and moment is also negligible,
where as we have used 2 nos of anchor bolts M16 of 4.6 grade for the same
having a tensile capacity of 30 kN and shear capacity of 25 kN. It can be
observed that the support reactions are very minor and negligible. Hence the base
plate Design not shown. The size of base plate is 300mm x 170mm x16mm & the
depth of anchor bolt is 300mm.
9 FOUNDATION DESIGN
Soil characteristics for all the foundations shall be established from existing
Geotechnical Investigation Reports for tank farm area. Maximum allowable
settlement in platform foundations shall be 25 mm. General design of foundations
shall be in accordance with BS 8004.
The minimum factors of safety for stability checks shall be as follow:
Overturning - 2.0
Sliding - 1.5
Uplift - 2.0
Geotechnical parameters such as safe bearing capacity of soil, densities, angle of

internal friction, lateral earth pressure coefficients, recommended friction coefficients
etc. which are used in foundation design shall be referred from the available
geotechnical investigation reports of respective areas.

9.1 FOUNDATION DESIGN FOR SRTINGER

The Foundation design for Walkover Bridge done for maximum forces. Typical
details are as given below. Maximum forces for node no. 57 & 60


Check for Crack width:

9.2 FOUNDATION DESIGN FOR COLUMN

The Foundation design for Walkover Bridge done for maximum forces. Typical
details are as given below. Maximum forces for node no. 43 & 45


Check for crack width:

ATTACHMENT - A
(STAAD INPUT / OUTPUT)

Monday, July 10, 2017, 07:51 PM
PAGE NO. 1
****************************************************
* *
* STAAD.Pro V8i SELECTseries4 *
* Version 20.07.09.31 *
* Proprietary Program of *
* Bentley Systems, Inc. *
* Date= JUL 3, 2017 *
* Time= 17:29: 4 *
* *
* USER ID: *
****************************************************
1. STAAD SPACE
INPUT FILE: TYPE - 1.STD
2. START JOB INFORMATION
3. ENGINEER DATE 11-MAY-17
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER KN
7. JOINT COORDINATES
8. 2 1.981 1.6 0; 3 8.231 1.6 0; 6 1.981 1.6 1; 7 8.231 1.6 1; 43 1.981 0 0
9. 44 8.231 0 0; 45 1.981 0 1; 46 8.231 0 1; 49 1.981 1.1 0; 50 8.231 1.1 0
10. 51 1.981 1.1 1; 52 8.231 1.1 1; 55 1.981 1.6 0.5; 56 8.231 1.6 0.5; 57 0 0 0
11. 59 10.21 0 0; 60 0 0 1; 62 10.21 0 1; 63 1.73337 1.4 0; 64 1.48575 1.2 0
12. 65 1.23812 1 0; 66 0.9905 0.8 0; 67 0.742875 0.6 0; 68 0.49525 0.4 0
13. 69 0.247625 0.2 0; 70 8.4775 1.4 0; 71 8.725 1.2 0; 72 8.9725 1 0
14. 73 9.22 0.8 0; 74 9.4675 0.6 0; 75 9.715 0.4 0; 76 9.9625 0.2 0
15. 77 0.247625 0.2 1; 78 0.49525 0.4 1; 79 0.742875 0.6 1; 80 0.9905 0.8 1
16. 81 1.23812 1 1; 82 1.48575 1.2 1; 83 1.73337 1.4 1; 84 8.4775 1.4 1
17. 85 8.725 1.2 1; 86 8.9725 1 1; 87 9.22 0.8 1; 88 9.4675 0.6 1; 89 9.715 0.4 1
18. 90 9.9625 0.2 1; 91 3.5435 1.6 0; 92 5.106 1.6 0; 93 6.6685 1.6 0
19. 94 3.54325 1.6 1; 95 5.1055 1.6 1; 96 6.66775 1.6 1
20. MEMBER INCIDENCES
21. 7 2 55; 8 3 56; 43 2 49; 44 3 50; 45 6 51; 46 7 52; 52 49 43; 53 50 44
22. 54 51 45; 55 52 46; 58 55 6; 59 56 7; 61 49 55; 62 51 55; 65 50 56; 66 52 56
23. 68 2 63; 72 60 77; 75 63 64; 76 64 65; 77 65 66; 78 66 67; 79 67 68; 80 68 69
24. 81 69 57; 82 70 71; 83 71 72; 84 72 73; 85 73 74; 86 74 75; 87 75 76; 88 76 59
25. 89 77 78; 90 78 79; 91 79 80; 92 80 81; 93 81 82; 94 82 83; 95 83 6; 96 84 85
26. 97 85 86; 98 86 87; 99 87 88; 100 88 89; 101 89 90; 102 90 62; 103 2 91
27. 104 6 94; 105 91 92; 106 92 93; 107 93 3; 108 94 95; 109 95 96; 110 96 7
28. 111 91 94; 112 92 95; 113 93 96; 114 2 94; 115 94 92; 116 92 96; 117 96 3
29. 118 3 70; 119 7 84
30. DEFINE MATERIAL START
31. ISOTROPIC STEEL
32. E 2.05E+008
33. POISSON 0.3
34. DENSITY 76.8195
35. ALPHA 1.2E-005
36. DAMP 0.03
37. TYPE STEEL
38. STRENGTH FY 253200 FU 407800 RY 1.5 RT 1.2
\\Dc-2\e\EU-166 EPIC OF WALKOVER BRIDGES IN TANK FARM AREA & REFINERY MESAIEED\3. Doc\Pdoc\DESIGN REPORT\LC161076-MTKF-1-12-0
Page 1 of 140
Monday, July 10, 2017, 07:51 PM
STAAD SPACE -- PAGE NO. 2
39. END DEFINE MATERIAL

40. MEMBER PROPERTY BRITISH
41. 61 62 65 66 111 TO 117 TABLE ST UA50X50X6
42. 43 TO 46 52 TO 55 68 72 75 TO 102 118 119 TABLE ST CH150X75X18
43. 7 8 58 59 TABLE ST CH100X50X10
44. 103 TO 110 TABLE ST CH200X75X23
45. CONSTANTS
46. BETA 45 MEMB 61 62 65 66 111 TO 117
47. MATERIAL STEEL ALL
48. SUPPORTS
49. 43 TO 46 57 59 60 62 FIXED BUT MY MZ
50. MEMBER RELEASE
51. 43 TO 46 68 118 119 START MY MZ
52. 95 END MY MZ
53. MEMBER TRUSS
54. 61 62 65 66 111 TO 117
55. DEFINE WIND LOAD
56. TYPE 1 WIND 1
57. INT 1.25 HEIG 1.6
58. EXP 1 JOINT 2 3 6 7 43 TO 46 49 TO 52 55 TO 57 59 60 62 TO 69 72 74 TO 96
59. LOAD 1 LOADTYPE NONE TITLE DL
60. SELFWEIGHT Y -1.1
61. JOINT LOAD
62. 63 TO 90 FY -0.05
63. 2 3 6 7 65 69 72 76 77 81 86 90 FY -0.2
64. MEMBER LOAD
65. 103 TO 110 CON GY -0.2 1.2 0
66. MEMBER LOAD
67. 103 TO 110 UNI GY -0.2
68. LOAD 2 LOADTYPE NONE TITLE LL
69. JOINT LOAD
70. 63 TO 90 FY -0.625
71. MEMBER LOAD
72. 103 TO 110 UNI GY -2.5
73. LOAD 3 LOADTYPE NONE TITLE WL(+X)
74. WIND LOAD X 1 TYPE 1 XR 0 10.21 YR 0 1.6 ZR 0 1 OPEN
75. LOAD 4 LOADTYPE NONE TITLE WL(-X)
76. WIND LOAD X -1 TYPE 1 XR 0 10.21 YR 0 1.6 ZR 0 1 OPEN
77. LOAD 5 LOADTYPE NONE TITLE WL(+Z)
78. WIND LOAD Z 1 TYPE 1 XR 0 10.21 YR 0 1.6 ZR 0 1 OPEN
79. LOAD 6 LOADTYPE NONE TITLE WL(-Z)
80. WIND LOAD Z -1 TYPE 1 XR 0 10.21 YR 0 1.6 ZR 0 1 OPEN
81. *************ALL SLS**********
82. LOAD COMB 101 1.DL+1.0LL
Page 2 of 140
Monday, July 10, 2017, 07:51 PM
83. 1 1.0 2 1.0

84. LOAD COMB 102 1.0DL+1.0WL(+X)
85. 1 1.0 3 1.0
86. LOAD COMB 103 1.0DL+1.0WL(-X)
87. 1 1.0 4 1.0
88. LOAD COMB 104 1.0DL+1.0WL(+Z)
89. 1 1.0 5 1.0
90. LOAD COMB 105 1.0DL+1.0WL(-Z)
91. 1 1.0 6 1.0
92. LOAD COMB 106 1.0DL+1.0LL+1.0WL(+X)
93. 1 1.0 2 1.0 3 1.0
94. LOAD COMB 107 1.0DL+1.0LL+1.0WL(-X)
95. 1 1.0 2 1.0 4 1.0
96. LOAD COMB 108 1.0DL+1.0LL+1.0WL(+Z)
97. 1 1.0 2 1.0 5 1.0
98. LOAD COMB 109 1.0DL+1.0LL+1.0WL(-Z)
99. 1 1.0 2 1.0 6 1.0
100. *************ALL ULS***********
101. LOAD COMB 201 1.35DL+1.5LL
102. 1 1.35 2 1.5
103. LOAD COMB 202 1.35DL+1.5WL(+X)
104. 1 1.35 3 1.5
105. LOAD COMB 203 1.35DL+1.5WL(-X)
106. 1 1.35 4 1.5
107. LOAD COMB 204 1.35DL+1.5WL(+Z)
108. 1 1.35 5 1.5
109. LOAD COMB 205 1.35DL+1.5WL(-Z)
110. 1 1.35 6 1.5
111. LOAD COMB 206 1.35DL+1.5LL+0.75WL(+X)
112. 1 1.35 2 1.5 3 0.75
113. LOAD COMB 207 1.35DL+1.5LL+0.75WL(-X)
114. 1 1.35 2 1.5 4 0.75
115. LOAD COMB 208 1.35DL+1.5L+0.75WL(+Z)
116. 1 1.35 2 1.5 5 0.75
117. LOAD COMB 209 1.35DL+1.5L+0.75WL(-Z)
118. 1 1.35 2 1.5 6 0.75
119. PERFORM ANALYSIS
P R O B L E M S T A T I S T I C S
-----------------------------------
NUMBER OF JOINTS 52 NUMBER OF MEMBERS 63

NUMBER OF PLATES 0 NUMBER OF SOLIDS 0
NUMBER OF SURFACES 0 NUMBER OF SUPPORTS 8
SOLVER USED IS THE OUT-OF-CORE BASIC SOLVER
ORIGINAL/FINAL BAND-WIDTH= 50/ 6/ 42 DOF

TOTAL PRIMARY LOAD CASES = 6, TOTAL DEGREES OF FREEDOM = 280
SIZE OF STIFFNESS MATRIX = 12 DOUBLE KILO-WORDS
Page 3 of 140
Monday, July 10, 2017, 07:51 PM
REQRD/AVAIL. DISK SPACE = 12.2/ 0.0 MB
120. DEFINE ENVELOPE

121. 101 TO 109 ENVELOPE 1 TYPE SERVICEABILITY
122. 201 TO 209 ENVELOPE 2 TYPE STRENGTH
123. END DEFINE ENVELOPE
124. ***************************
125. LOAD LIST 101 TO 109
126. PARAMETER 1
127. CODE EN 1993-1-1:2005
128. DFF 360 MEMB 7 8 58 59 68 72 75 TO 113 118 119
129. DJ1 2 MEMB 103 105 TO 107
130. DJ2 3 MEMB 103 105 TO 107
131. DJ1 6 MEMB 104 108 TO 110
132. DJ2 7 MEMB 104 108 TO 110
133. DFF 200 MEMB 43 TO 46 52 TO 55
134. TRACK 4 ALL
135. CHECK CODE ALL
STAAD.PRO CODE CHECKING - EN 1993-1-1:2005

********************************************
NATIONAL ANNEX - NOT USED
PROGRAM CODE REVISION V1.9 BS_EC3_2005/1
Page 4 of 140
Monday, July 10, 2017, 07:51 PM
Page 5 of 140
Monday, July 10, 2017, 07:51 PM
DEFLECTION CHECKS
LENGTH UNITS - METE
MEMBER TABLE RESULT

ACTUAL DEFL. DEFL.LEN/ LOAD/
DEFL. LIMIT DFF LOCATION
=======================================================================
7 ST CH100X50X10 (BRITISH SECTIONS)

PASS 0.000 0.001 0.500 108
360.000 0.00
PASS 0.000 0.001 0.500 108
360.000 0.00
PASS 0.000 0.002 0.500 109
200.000 0.00
PASS 0.000 0.002 0.500 109
200.000 0.00
PASS 0.000 0.002 0.500 108
200.000 0.00
PASS 0.000 0.002 0.500 108
200.000 0.00
PASS 0.000 0.005 1.100 109
200.000 0.00
PASS 0.000 0.005 1.100 109
200.000 0.00
PASS 0.000 0.005 1.100 108
200.000 0.00
PASS 0.000 0.005 1.100 108
200.000 0.00
PASS 0.000 0.001 0.500 108
360.000 0.00
Page 6 of 140
Monday, July 10, 2017, 07:51 PM
DEFLECTION CHECKS
LENGTH UNITS - METE
MEMBER TABLE RESULT ACTUAL DEFL. DEFL.LEN/ LOAD/

=======================================================================

PASS 0.000 0.001 0.500 108
360.000 0.00
61 ST UA50X50X6 (BRITISH SECTIONS)
PASS 0.000 0.001 0.500 108
0.000 0.00
PASS 0.000 0.001 0.500 108
0.000 0.00
PASS 0.000 0.001 0.500 108
0.000 0.00
PASS 0.000 0.001 0.500 108
0.000 0.00
PASS 0.000 0.001 0.318 108
360.000 0.00
PASS 0.000 0.001 0.318 108
360.000 0.00
PASS 0.000 0.001 0.318 108
360.000 0.00
PASS 0.000 0.001 0.318 109
360.000 0.00
PASS 0.000 0.001 0.318 108
360.000 0.00
PASS 0.000 0.001 0.318 109
360.000 0.00
Page 7 of 140
Monday, July 10, 2017, 07:51 PM
DEFLECTION CHECKS
LENGTH UNITS - METE
MEMBER TABLE RESULT ACTUAL DEFL. DEFL.LEN/ LOAD/

=======================================================================

PASS 0.000 0.001 0.318 108
360.000 0.00
PASS 0.000 0.001 0.318 109
360.000 0.00
PASS 0.000 0.001 0.318 108
360.000 0.00
PASS 0.000 0.001 0.318 109
360.000 0.00
PASS 0.000 0.001 0.318 108
360.000 0.00
PASS 0.000 0.001 0.318 109
360.000 0.00
PASS 0.000 0.001 0.318 108
360.000 0.00
PASS 0.000 0.001 0.318 109
360.000 0.00
PASS 0.000 0.001 0.318 109
360.000 0.00
PASS 0.000 0.001 0.318 109
360.000 0.00
PASS 0.000 0.001 0.318 109
360.000 0.00
Page 8 of 140
Monday, July 10, 2017, 07:51 PM
DEFLECTION CHECKS
LENGTH UNITS - METE
MEMBER TABLE RESULTACTUAL DEFL. DEFL.LEN/ LOAD/

=======================================================================

PASS 0.000 0.001 0.318 109
360.000 0.00
PASS 0.000 0.001 0.318 109
360.000 0.00
PASS 0.000 0.001 0.318 108
360.000 0.00
PASS 0.000 0.001 0.318 109
360.000 0.00
PASS 0.000 0.001 0.318 108
360.000 0.00
PASS 0.000 0.001 0.318 108
360.000 0.00
PASS 0.000 0.001 0.318 108
360.000 0.00
PASS 0.000 0.001 0.318 109
360.000 0.00
PASS 0.000 0.001 0.318 109
360.000 0.00
PASS 0.000 0.001 0.318 109
360.000 0.00
PASS 0.000 0.001 0.318 109
360.000 0.00
Page 9 of 140
Monday, July 10, 2017, 07:51 PM
DEFLECTION CHECKS
LENGTH UNITS - METE
MEMBER TABLE RESULTACTUAL DEFL. DEFL.LEN/ LOAD/

=======================================================================

PASS 0.000 0.001 0.318 109
360.000 0.00
PASS 0.000 0.001 0.318 109
360.000 0.00
PASS 0.011 0.017 6.250 108
360.000 0.00
PASS 0.011 0.017 6.250 108
360.000 0.00
PASS 0.016 0.017 6.250 109
360.000 0.00
PASS 0.016 0.017 6.250 109
360.000 0.00
PASS 0.011 0.017 6.250 108
360.000 0.00
PASS 0.016 0.017 6.250 108
360.000 0.00
PASS 0.016 0.017 6.250 108
360.000 0.00
PASS 0.011 0.017 6.250 108
360.000 0.00
PASS 0.000 0.003 1.000 108
360.000 0.00
Page 10 of 140
Monday, July 10, 2017, 07:51 PM
DEFLECTION CHECKS
LENGTH UNITS - METE
MEMBER TABLE RESULT

ACTUAL DEFL. DEFL.LEN/ LOAD/
=======================================================================

PASS 0.000 0.003 1.000 107
360.000 0.00
PASS 0.000 0.003 1.000 109
360.000 0.00
PASS 0.000 0.003 1.000 109
0.000 0.00
PASS 0.000 0.003 1.000 109
0.000 0.00
PASS 0.000 0.003 1.000 109
0.000 0.00
PASS 0.000 0.003 1.000 109
0.000 0.00
PASS 0.000 0.001 0.317 108
360.000 0.00
PASS 0.000 0.001 0.317 108
360.000 0.00
************** END OF TABULATED RESULT OF DESIGN **************
136. ***************************
137. LOAD LIST 201 TO 209
138. PARAMETER 2
139. CODE EN 1993-1-1:2005
140. PY 275000 ALL
141. RATIO 1 ALL
142. TRACK 2 ALL
143. LZ 6.25 MEMB 103 TO 110
144. KY 2 MEMB 43 TO 46 52 TO 55
145. LY 2.55 MEMB 68 72 75 TO 102 118 119
146. UNL 2.55 MEMB 68 72 75 TO 102 118 119
147. LZ 2.55 MEMB 68 72 75 TO 102 118 119
148. CHECK CODE ALL
STAAD.PRO CODE CHECKING - EN 1993-1-1:2005

********************************************
NATIONAL ANNEX - NOT USED
PROGRAM CODE REVISION V1.9 BS_EC3_2005/1
Page 11 of 140
Monday, July 10, 2017, 07:51 PM
ALL UNITS ARE - KN METE (UNLESS OTHERWISE Noted)
MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.025 204
5.22 C -0.05 0.00 0.00

=======================================================================
MATERIAL DATA
Grade of steel = USER
Modulus of elasticity = 205 kN/mm2
Design Strength (py) = 275 N/mm2
SECTION PROPERTIES (units - cm)

Member Length = 50.00
Gross Area = 13.00 Net Area = 13.00
z-axis y-axis
Moment of inertia : 208.000 32.300
Plastic modulus : 48.900 17.500
Elastic modulus : 41.600 9.788
Shear Area : 5.667 5.000
Radius of gyration : 4.000 1.576
Effective Length : 50.000 50.000
DESIGN DATA (units - kN,m) EUROCODE NO.3 /2005

Section Class : CLASS 1
Squash Load : 357.50
Axial force/Squash load : 0.015
GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis
Slenderness ratio (KL/r) : 12.5 52.2
Compression Capacity : 357.5 280.5
Tension Capacity : 337.0 337.0
Moment Capacity : 13.4 4.8
Reduced Moment Capacity : 13.4 4.8
Shear Capacity : 90.0 89.7
BUCKLING CALCULATIONS (units - kN,m)

Lateral Torsional Buckling Moment MB = 13.4
co-efficients C1 K : C1 =1.132 K =1.0, Effective Length= 0.500
Elastic Critical Moment for LTB, Mcr = 89.5
Critical Load For Torsional Buckling, NcrT = 1983.3
Critical Load For Torsional-Flexural Buckling, NcrTF = 1889.8
Page 12 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================
CRITICAL LOADS FOR EACH CLAUSE CHECK (units- kN,m):

CLAUSE RATIO LOAD FX VY VZ MZ MY
EC-6.2.3 (T) 0.016 205 -5.3 0.1 -0.1 0.0 0.0
EC-6.3.1.1 0.019 204 5.2 0.1 0.1 0.0 -0.1
EC-6.2.9.1 0.011 204 5.2 0.1 0.1 0.0 -0.1
EC-6.3.3-661 0.019 204 5.2 0.1 0.1 0.0 -0.1
EC-6.3.3-662 0.025 204 5.2 0.1 0.1 0.0 -0.1
EC-6.2.6-(Z) 0.002 202 0.0 0.1 0.1 0.0 0.0
EC-6.3.2 LTB 0.001 201 -0.1 0.1 0.0 0.0 0.0
Torsion and deflections have not been considered in the design.
_________________________
Page 13 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.025 204
5.20 C 0.05 0.00 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 5.667 5.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 14 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.016 205 -5.2 0.1 0.1 0.0 0.0
EC-6.3.1.1 0.019 204 5.2 0.1 -0.1 0.0 0.1
EC-6.2.9.1 0.011 204 5.2 0.1 -0.1 0.0 0.1
EC-6.3.3-661 0.019 204 5.2 0.1 -0.1 0.0 0.1
EC-6.3.3-662 0.025 204 5.2 0.1 -0.1 0.0 0.1
EC-6.2.6-(Z) 0.002 202 0.0 0.1 0.1 0.0 0.0
EC-6.3.2 LTB 0.001 201 -0.1 0.1 0.0 0.0 0.0
_________________________
Page 15 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.2.9.1 0.082 205
1.93 C -1.06 0.00 0.50

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 16 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.3.1.1 0.036 208 16.8 0.0 -1.0 0.0 -0.4
EC-6.2.9.1 0.082 205 1.9 0.0 -2.0 0.0 -1.1
EC-6.3.3-661 0.041 208 16.8 0.0 0.9 0.0 0.5
EC-6.3.3-662 0.061 208 16.8 0.0 0.9 0.0 0.5
EC-6.2.6-(Z) 0.014 205 1.8 0.0 2.3 0.0 0.0
EC-6.2.6-(Y) 0.001 202 3.7 -0.2 0.0 0.0 0.0
EC-6.3.2 LTB 0.002 202 3.8 -0.1 0.0 0.1 0.0
_________________________
Page 17 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.2.9.1 0.083 205
2.17 C -1.07 0.00 0.50

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 18 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.3.1.1 0.037 208 16.9 0.0 -1.0 0.0 -0.4
EC-6.2.9.1 0.083 205 2.2 0.0 -2.0 0.0 -1.1
EC-6.3.3-661 0.042 208 16.9 0.0 0.9 0.0 0.5
EC-6.3.3-662 0.061 208 16.9 0.0 0.9 0.0 0.5
EC-6.2.6-(Z) 0.014 205 2.0 0.0 2.3 0.0 0.0
EC-6.2.6-(Y) 0.001 202 2.6 -0.2 0.0 0.0 0.0
EC-6.3.2 LTB 0.002 202 2.8 -0.1 0.0 0.1 0.0
_________________________
Page 19 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.2.9.1 0.082 204
2.21 C 1.07 0.00 0.50

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 20 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.3.1.1 0.036 209 16.6 0.0 1.0 0.0 0.4
EC-6.2.9.1 0.082 204 2.2 0.0 2.0 0.0 1.1
EC-6.3.3-661 0.041 209 16.7 0.0 -0.9 0.0 -0.5
EC-6.3.3-662 0.061 208 15.6 0.0 1.0 0.0 0.6
EC-6.2.6-(Z) 0.014 204 2.1 0.0 -2.3 0.0 0.0
EC-6.2.6-(Y) 0.001 202 3.7 -0.2 0.0 0.0 0.0
EC-6.3.2 LTB 0.002 202 3.8 -0.1 0.0 0.1 0.0
_________________________
Page 21 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.2.9.1 0.083 204
2.45 C 1.08 0.00 0.50

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 22 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.3.1.1 0.036 209 16.7 0.0 1.0 0.0 0.4
EC-6.2.9.1 0.083 204 2.4 0.0 2.0 0.0 1.1
EC-6.3.3-661 0.041 208 15.8 0.0 1.0 0.0 0.6
EC-6.3.3-662 0.061 208 15.8 0.0 1.0 0.0 0.6
EC-6.2.6-(Z) 0.014 204 2.3 0.0 -2.3 0.0 0.0
EC-6.2.6-(Y) 0.001 202 2.6 -0.2 0.0 0.0 0.0
EC-6.3.2 LTB 0.002 202 2.8 -0.1 0.0 0.1 0.0
_________________________
Page 23 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.2.9.1 0.117 205
6.38 C 1.52 0.00 1.10

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 24 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.3.1.1 0.058 209 17.9 0.0 1.3 0.0 0.8
EC-6.2.9.1 0.117 205 6.4 0.0 2.5 0.0 1.5
EC-6.3.3-661 0.044 209 17.9 0.0 1.3 0.0 0.8
EC-6.3.3-662 0.083 209 17.9 0.0 1.3 0.0 0.8
EC-6.2.6-(Z) 0.016 205 6.4 0.0 2.5 0.0 1.5
EC-6.3.2 LTB 0.002 202 3.9 0.0 0.0 0.1 0.0
_________________________
Page 25 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.2.9.1 0.118 205
6.67 C 1.54 0.00 1.10

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 26 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.3.1.1 0.059 209 18.2 0.0 1.3 0.0 0.8
EC-6.2.9.1 0.118 205 6.7 0.0 2.5 0.0 1.5
EC-6.3.3-661 0.044 209 18.2 0.0 1.3 0.0 0.8
EC-6.3.3-662 0.084 209 18.2 0.0 1.3 0.0 0.8
EC-6.2.6-(Z) 0.016 205 6.7 0.0 2.5 0.0 1.5
EC-6.3.2 LTB 0.002 202 2.8 0.0 0.0 0.1 0.0
_________________________
Page 27 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.2.9.1 0.117 204
6.67 C -1.52 0.00 1.10

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 28 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.3.1.1 0.059 208 18.1 0.0 -1.3 0.0 -0.8
EC-6.2.9.1 0.117 204 6.7 0.0 -2.5 0.0 -1.5
EC-6.3.3-661 0.044 208 18.1 0.0 -1.3 0.0 -0.8
EC-6.3.3-662 0.084 208 18.1 0.0 -1.3 0.0 -0.8
EC-6.2.6-(Z) 0.016 204 6.7 0.0 -2.5 0.0 -1.5
EC-6.3.2 LTB 0.002 202 3.9 0.0 0.0 0.1 0.0
_________________________
Page 29 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.2.9.1 0.118 204
6.95 C -1.54 0.00 1.10

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 30 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.3.1.1 0.059 208 18.3 0.0 -1.3 0.0 -0.8
EC-6.2.9.1 0.118 204 7.0 0.0 -2.5 0.0 -1.5
EC-6.3.3-661 0.044 208 18.3 0.0 -1.3 0.0 -0.8
EC-6.3.3-662 0.085 208 18.3 0.0 -1.3 0.0 -0.8
EC-6.2.6-(Z) 0.016 204 7.0 0.0 -2.5 0.0 -1.5
EC-6.3.2 LTB 0.002 202 2.8 0.0 0.0 0.1 0.0
_________________________
Page 31 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.017 205
2.87 C 0.05 0.00 0.50

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 5.667 5.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 32 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.009 204 -2.9 0.0 0.1 0.0 0.0
EC-6.3.1.1 0.010 205 2.9 0.0 -0.1 0.0 0.0
EC-6.2.9.1 0.011 204 -2.9 0.0 -0.1 0.0 -0.1
EC-6.3.3-661 0.012 205 2.9 0.1 0.1 0.0 0.0
EC-6.3.3-662 0.017 205 2.9 0.1 0.1 0.0 0.0
EC-6.2.6-(Z) 0.002 202 0.0 0.1 0.1 0.0 0.0
EC-6.3.2 LTB 0.001 201 -0.1 0.1 0.0 0.0 0.0
_________________________
Page 33 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.017 205
2.97 C -0.05 0.00 0.50

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 5.667 5.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 34 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.009 204 -3.0 0.0 -0.1 0.0 0.0
EC-6.3.1.1 0.011 205 3.0 0.0 0.1 0.0 0.0
EC-6.2.9.1 0.011 204 -3.0 0.0 0.1 0.0 0.1
EC-6.3.3-661 0.012 205 3.0 0.1 -0.1 0.0 0.0
EC-6.3.3-662 0.017 205 3.0 0.1 -0.1 0.0 0.0
EC-6.2.6-(Z) 0.002 202 0.0 0.1 0.1 0.0 0.0
EC-6.3.2 LTB 0.001 201 -0.1 0.1 0.0 0.0 0.0
_________________________
Page 35 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.1.1 0.054 205
5.91 C 0.00 0.00 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 2.000 2.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 36 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.039 204 -5.8 0.0 0.0 0.0 0.0
EC-6.3.1.1 0.054 205 5.9 0.0 0.0 0.0 0.0
_________________________
Page 37 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.1.1 0.054 204
5.92 C 0.00 0.00 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 2.000 2.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 38 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.039 205 -5.8 0.0 0.0 0.0 0.0
EC-6.3.1.1 0.054 204 5.9 0.0 0.0 0.0 0.0
_________________________
Page 39 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.1.1 0.055 205
5.97 C 0.00 0.00 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 2.000 2.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 40 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.039 204 -5.8 0.0 0.0 0.0 0.0
EC-6.3.1.1 0.055 205 6.0 0.0 0.0 0.0 0.0
_________________________
Page 41 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.1.1 0.055 204
5.98 C 0.00 0.00 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 2.000 2.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 42 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.040 205 -5.8 0.0 0.0 0.0 0.0
EC-6.3.1.1 0.055 204 6.0 0.0 0.0 0.0 0.0
_________________________
Page 43 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.066 209
2.64 C 0.06 0.99 0.32

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 44 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.003 204 -1.7 0.6 0.4 0.0 0.0
EC-6.3.1.1 0.010 209 2.6 3.1 -0.2 -0.6 0.0
EC-6.2.9.1 0.032 208 0.6 -3.1 -0.1 1.0 -0.1
EC-6.3.3-661 0.039 209 2.6 -3.1 0.1 1.0 0.1
EC-6.3.3-662 0.066 209 2.6 -3.1 0.1 1.0 0.1
EC-6.2.6-(Z) 0.003 204 -1.7 0.6 0.4 0.0 0.0
EC-6.2.6-(Y) 0.021 206 1.1 3.2 0.0 0.0 0.0
EC-6.3.2 LTB 0.040 206 1.1 -3.1 0.0 1.0 0.0
_________________________
Page 45 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.086 208
7.48 C 0.05 1.03 0.32

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 46 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.3.1.1 0.028 208 7.5 3.3 -0.2 0.0 0.0
EC-6.2.9.1 0.032 208 7.5 -3.2 0.1 1.0 0.0
EC-6.3.3-661 0.049 208 7.5 -3.2 0.1 1.0 0.0
EC-6.3.3-662 0.086 208 7.5 -3.2 0.1 1.0 0.0
EC-6.2.6-(Z) 0.002 204 3.0 0.7 -0.4 0.0 0.0
EC-6.2.6-(Y) 0.022 206 6.2 3.3 0.0 0.0 0.0
EC-6.3.2 LTB 0.042 206 6.2 -3.2 0.0 1.0 0.0
_________________________
Page 47 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.111 209
3.32 C 0.09 1.72 0.32

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 48 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.003 204 -1.6 0.5 0.3 -0.2 0.1
EC-6.3.1.1 0.012 209 3.3 2.3 -0.1 -1.4 -0.1
EC-6.2.9.1 0.054 208 1.2 -2.2 -0.1 1.7 -0.1
EC-6.3.3-661 0.087 209 3.3 -2.2 0.1 1.7 0.1
EC-6.3.3-662 0.111 209 3.3 -2.2 0.1 1.7 0.1
EC-6.2.6-(Z) 0.002 204 -1.6 0.5 0.3 -0.2 0.1
EC-6.2.6-(Y) 0.015 206 1.8 2.3 0.0 -1.0 0.0
EC-6.3.2 LTB 0.069 206 1.8 -2.3 0.0 1.7 0.0
_________________________
Page 49 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.140 209
4.01 C 0.11 2.17 0.32

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 50 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.003 204 -1.5 0.4 0.2 -0.3 0.2
EC-6.3.1.1 0.015 209 4.0 1.4 -0.1 -2.0 -0.1
EC-6.2.9.1 0.068 208 1.9 -1.4 0.0 2.2 -0.1
EC-6.3.3-661 0.120 209 4.0 -1.4 0.0 2.2 0.1
EC-6.3.3-662 0.140 209 4.0 -1.4 0.0 2.2 0.1
EC-6.2.6-(Z) 0.001 204 -1.5 0.4 0.2 -0.3 0.2
EC-6.2.6-(Y) 0.010 206 2.5 1.5 0.0 -1.7 0.0
EC-6.3.2 LTB 0.088 206 2.5 -1.4 0.0 2.2 0.0
_________________________
Page 51 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.151 209
4.86 C 0.12 2.29 0.32

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 52 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 204 -1.2 0.0 0.1 -0.4 0.2
EC-6.3.1.1 0.018 209 4.8 0.4 0.0 -2.2 -0.1
EC-6.2.9.1 0.072 208 2.8 -0.3 0.0 2.3 -0.1
EC-6.3.3-661 0.136 209 4.9 -0.3 0.0 2.3 0.1
EC-6.3.3-662 0.151 209 4.9 -0.3 0.0 2.3 0.1
EC-6.2.6-(Y) 0.003 201 3.8 0.4 0.0 -2.2 0.0
EC-6.3.2 LTB 0.093 206 3.3 -0.3 0.0 2.3 0.0
_________________________
Page 53 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.153 209
5.49 C -0.12 -2.29 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 54 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 204 -1.2 -0.1 0.0 -0.4 0.2
EC-6.3.1.1 0.021 209 5.5 -0.5 0.0 -2.2 -0.1
EC-6.2.9.1 0.072 208 3.4 -0.4 0.0 -2.3 0.1
EC-6.3.3-661 0.136 209 5.5 -0.4 0.0 -2.3 -0.1
EC-6.3.3-662 0.153 209 5.5 -0.4 0.0 -2.3 -0.1
EC-6.2.6-(Y) 0.003 201 4.5 0.5 0.0 2.1 0.0
EC-6.3.2 LTB 0.093 206 4.0 -0.4 0.0 -2.3 0.0
_________________________
Page 55 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.146 209
6.17 C -0.11 -2.14 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 56 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 204 -1.1 -0.2 -0.1 -0.4 0.2
EC-6.3.1.1 0.023 209 6.2 -1.3 0.1 -1.9 -0.1
EC-6.2.9.1 0.067 208 4.1 -1.3 0.0 -2.1 0.1
EC-6.3.3-661 0.123 209 6.2 -1.3 0.0 -2.1 -0.1
EC-6.3.3-662 0.146 209 6.2 -1.3 0.0 -2.1 -0.1
EC-6.2.5 0.012 202 0.0 -0.2 0.0 -0.4 0.0
EC-6.2.6-(Z) 0.001 204 -1.0 0.3 0.2 0.3 -0.2
EC-6.2.6-(Y) 0.009 206 4.7 1.4 0.0 1.7 0.0
EC-6.3.2 LTB 0.086 206 4.6 -1.3 0.0 -2.2 0.0
_________________________
Page 57 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.124 209
6.86 C -0.09 -1.72 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 58 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 204 -1.0 -0.3 -0.2 -0.3 0.2
EC-6.3.1.1 0.026 209 6.9 -2.2 0.1 -1.3 -0.1
EC-6.2.9.1 0.054 208 4.8 -2.1 -0.1 -1.7 0.1
EC-6.3.3-661 0.094 209 6.9 -2.1 0.1 -1.7 -0.1
EC-6.3.3-662 0.124 209 6.9 -2.1 0.1 -1.7 -0.1
EC-6.2.5 0.010 202 0.1 -0.3 0.0 -0.4 0.0
EC-6.2.6-(Z) 0.002 204 -0.9 0.4 0.3 0.2 -0.1
EC-6.2.6-(Y) 0.015 206 5.3 -2.2 0.0 -1.1 0.0
EC-6.3.2 LTB 0.069 206 5.3 -2.2 0.0 -1.7 0.0
_________________________
Page 59 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.087 209
7.71 C -0.05 -1.03 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 60 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.001 204 -0.7 -0.6 -0.3 -0.2 0.1
EC-6.3.1.1 0.029 209 7.7 -3.2 0.2 -0.4 0.0
EC-6.2.9.1 0.032 208 5.6 -3.2 -0.1 -1.0 0.1
EC-6.3.3-661 0.049 209 7.7 -3.2 0.1 -1.0 -0.1
EC-6.3.3-662 0.087 209 7.7 -3.2 0.1 -1.0 -0.1
EC-6.2.6-(Z) 0.002 204 -0.6 0.7 0.4 0.0 0.0
EC-6.2.6-(Y) 0.022 206 6.2 3.3 0.0 0.0 0.0
EC-6.3.2 LTB 0.042 206 6.2 -3.2 0.0 -1.0 0.0
_________________________
Page 61 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.111 209
3.24 C -0.09 1.71 0.32

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 62 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 204 -1.4 0.5 -0.3 -0.2 -0.1
EC-6.3.1.1 0.012 209 3.2 2.3 0.1 -1.4 0.1
EC-6.2.9.1 0.054 208 1.3 -2.2 0.1 1.7 0.1
EC-6.3.3-661 0.087 209 3.2 -2.2 -0.1 1.7 -0.1
EC-6.3.3-662 0.111 209 3.2 -2.2 -0.1 1.7 -0.1
EC-6.2.6-(Z) 0.002 204 -1.4 0.5 -0.3 -0.2 -0.1
EC-6.2.6-(Y) 0.015 207 1.8 2.3 0.0 -1.0 0.0
EC-6.3.2 LTB 0.069 207 1.8 -2.3 0.0 1.7 0.0
_________________________
Page 63 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.140 209
3.93 C -0.11 2.17 0.32

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 64 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 204 -1.4 0.4 -0.2 -0.3 -0.2
EC-6.3.1.1 0.015 209 3.9 1.4 0.1 -2.0 0.1
EC-6.2.9.1 0.068 208 2.0 -1.4 0.0 2.2 0.1
EC-6.3.3-661 0.120 209 3.9 -1.4 0.0 2.2 -0.1
EC-6.3.3-662 0.140 209 3.9 -1.4 0.0 2.2 -0.1
EC-6.2.6-(Z) 0.001 204 -1.4 0.4 -0.2 -0.3 -0.2
EC-6.2.6-(Y) 0.010 207 2.5 1.5 0.0 -1.7 0.0
EC-6.3.2 LTB 0.088 207 2.5 -1.4 0.0 2.2 0.0
_________________________
Page 65 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.150 209
4.78 C -0.12 2.29 0.32

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 66 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 204 -1.1 0.0 -0.1 -0.4 -0.2
EC-6.3.1.1 0.018 209 4.8 0.4 0.0 -2.2 0.1
EC-6.2.9.1 0.072 208 2.9 -0.3 0.0 2.3 0.1
EC-6.3.3-661 0.136 209 4.8 -0.3 0.0 2.3 -0.1
EC-6.3.3-662 0.150 209 4.8 -0.3 0.0 2.3 -0.1
EC-6.2.6-(Y) 0.003 201 3.8 0.4 0.0 -2.2 0.0
EC-6.3.2 LTB 0.093 207 3.3 -0.3 0.0 2.3 0.0
_________________________
Page 67 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.153 209
5.41 C 0.12 -2.29 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 68 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 204 -1.0 -0.1 0.0 -0.4 -0.2
EC-6.3.1.1 0.021 209 5.4 -0.5 0.0 -2.2 0.1
EC-6.2.9.1 0.072 208 3.5 -0.4 0.0 -2.3 -0.1
EC-6.3.3-661 0.136 209 5.4 -0.4 0.0 -2.3 0.1
EC-6.3.3-662 0.153 209 5.4 -0.4 0.0 -2.3 0.1
EC-6.2.6-(Y) 0.003 201 4.5 0.5 0.0 2.1 0.0
EC-6.3.2 LTB 0.093 207 4.0 -0.4 0.0 -2.3 0.0
_________________________
Page 69 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.146 209
6.10 C 0.11 -2.14 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 70 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 204 -0.9 -0.2 0.1 -0.4 -0.2
EC-6.3.1.1 0.023 209 6.1 -1.3 -0.1 -1.9 0.1
EC-6.2.9.1 0.067 208 4.2 -1.3 0.0 -2.1 -0.1
EC-6.3.3-661 0.123 209 6.1 -1.3 0.0 -2.1 0.1
EC-6.3.3-662 0.146 209 6.1 -1.3 0.0 -2.1 0.1
EC-6.2.5 0.012 203 0.0 -0.2 0.0 -0.4 0.0
EC-6.2.6-(Z) 0.001 204 -0.8 0.3 -0.2 0.3 0.2
EC-6.2.6-(Y) 0.009 207 4.7 1.4 0.0 1.7 0.0
EC-6.3.2 LTB 0.086 207 4.6 -1.3 0.0 -2.2 0.0
_________________________
Page 71 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.124 209
6.78 C 0.09 -1.72 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 72 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.001 204 -0.8 -0.3 0.2 -0.3 -0.2
EC-6.3.1.1 0.026 209 6.8 -2.2 -0.1 -1.3 0.1
EC-6.2.9.1 0.054 208 4.9 -2.1 0.1 -1.7 -0.1
EC-6.3.3-661 0.094 209 6.8 -2.1 -0.1 -1.7 0.1
EC-6.3.3-662 0.124 209 6.8 -2.1 -0.1 -1.7 0.1
EC-6.2.5 0.010 203 0.1 -0.3 0.0 -0.4 0.0
EC-6.2.6-(Z) 0.002 204 -0.8 0.4 -0.3 0.2 0.1
EC-6.2.6-(Y) 0.015 207 5.3 -2.2 0.0 -1.1 0.0
EC-6.3.2 LTB 0.069 207 5.3 -2.2 0.0 -1.7 0.0
_________________________
Page 73 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.086 209
7.63 C 0.05 -1.03 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 74 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.3.1.1 0.029 209 7.7 -3.2 -0.2 -0.4 0.0
EC-6.2.9.1 0.032 208 5.7 -3.2 0.1 -1.0 -0.1
EC-6.3.3-661 0.049 209 7.6 -3.2 -0.1 -1.0 0.1
EC-6.3.3-662 0.086 209 7.6 -3.2 -0.1 -1.0 0.1
EC-6.2.6-(Z) 0.002 204 -0.5 0.7 -0.4 0.0 0.0
EC-6.2.6-(Y) 0.022 207 6.2 3.3 0.0 0.0 0.0
EC-6.3.2 LTB 0.041 207 6.2 -3.2 0.0 -1.0 0.0
_________________________
Page 75 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.123 208
6.63 C 0.08 1.72 0.32

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 76 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.3.1.1 0.025 208 6.7 2.2 -0.1 -1.0 0.0
EC-6.2.9.1 0.054 208 6.6 -2.1 0.1 1.7 0.1
EC-6.3.3-661 0.094 208 6.6 -2.1 0.1 1.7 0.1
EC-6.3.3-662 0.123 208 6.6 -2.1 0.1 1.7 0.1
EC-6.2.6-(Z) 0.002 204 2.8 0.4 -0.3 -0.2 -0.1
EC-6.2.6-(Y) 0.015 206 5.4 2.2 0.0 -1.0 0.0
EC-6.3.2 LTB 0.069 206 5.3 -2.2 0.0 1.7 0.0
_________________________
Page 77 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.145 208
5.95 C 0.11 2.14 0.32

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 78 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.3.1.1 0.023 208 6.0 1.4 -0.1 -1.7 -0.1
EC-6.2.9.1 0.067 208 5.9 -1.3 0.0 2.1 0.1
EC-6.3.3-661 0.122 208 5.9 -1.3 0.0 2.1 0.1
EC-6.3.3-662 0.145 208 5.9 -1.3 0.0 2.1 0.1
EC-6.2.5 0.012 202 0.0 -0.2 0.0 0.4 0.0
EC-6.2.6-(Z) 0.001 204 2.7 0.3 -0.2 -0.3 -0.2
EC-6.2.6-(Y) 0.009 206 4.7 1.4 0.0 -1.7 0.0
EC-6.3.2 LTB 0.086 206 4.7 -1.3 0.0 2.2 0.0
_________________________
Page 79 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.152 208
5.26 C 0.11 2.29 0.32

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 80 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.001 205 -0.6 0.1 0.1 -0.4 0.2
EC-6.3.1.1 0.020 208 5.3 0.5 0.0 -2.1 -0.1
EC-6.2.9.1 0.072 208 5.3 -0.4 0.0 2.3 0.1
EC-6.3.3-661 0.136 208 5.3 -0.4 0.0 2.3 0.1
EC-6.3.3-662 0.152 208 5.3 -0.4 0.0 2.3 0.1
EC-6.2.5 0.012 202 0.0 0.2 0.0 -0.4 0.0
EC-6.2.6-(Y) 0.003 201 4.5 0.5 0.0 -2.1 0.0
EC-6.3.2 LTB 0.093 206 4.0 -0.4 0.0 2.3 0.0
_________________________
Page 81 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.149 208
4.63 C -0.11 -2.29 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 82 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.001 205 -0.7 0.0 0.0 -0.4 0.2
EC-6.3.1.1 0.018 208 4.6 -0.3 0.0 -2.3 -0.1
EC-6.2.9.1 0.072 208 4.6 -0.3 0.0 -2.3 -0.1
EC-6.3.3-661 0.135 208 4.6 -0.3 0.0 -2.3 -0.1
EC-6.3.3-662 0.149 208 4.6 -0.3 0.0 -2.3 -0.1
EC-6.2.6-(Y) 0.003 201 3.8 0.4 0.0 2.2 0.0
EC-6.3.2 LTB 0.093 206 3.3 -0.3 0.0 -2.3 0.0
_________________________
Page 83 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.139 208
3.78 C -0.11 -2.17 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 84 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 205 -1.0 -0.3 -0.1 -0.4 0.2
EC-6.3.1.1 0.014 208 3.8 -1.4 0.0 -2.2 -0.1
EC-6.2.9.1 0.068 208 3.8 -1.4 0.0 -2.2 -0.1
EC-6.3.3-661 0.119 208 3.8 -1.4 0.0 -2.2 -0.1
EC-6.3.3-662 0.139 208 3.8 -1.4 0.0 -2.2 -0.1
EC-6.2.6-(Z) 0.001 204 2.2 0.4 -0.2 0.3 0.2
EC-6.2.6-(Y) 0.010 206 2.5 1.5 0.0 1.7 0.0
EC-6.3.2 LTB 0.088 206 2.5 -1.4 0.0 -2.2 0.0
_________________________
Page 85 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.110 208
3.10 C -0.09 -1.72 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 86 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 205 -1.1 -0.4 -0.2 -0.3 0.2
EC-6.3.1.1 0.012 208 3.1 -2.2 0.1 -1.7 -0.1
EC-6.2.9.1 0.054 208 3.1 -2.2 0.1 -1.7 -0.1
EC-6.3.3-661 0.086 208 3.1 -2.2 0.1 -1.7 -0.1
EC-6.3.3-662 0.110 208 3.1 -2.2 0.1 -1.7 -0.1
EC-6.2.6-(Z) 0.002 204 2.1 0.5 -0.3 0.2 0.1
EC-6.2.6-(Y) 0.015 206 1.8 -2.3 0.0 -1.1 0.0
EC-6.3.2 LTB 0.069 206 1.8 -2.3 0.0 -1.7 0.0
_________________________
Page 87 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.065 208
2.41 C -0.05 -0.99 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 88 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 205 -1.2 -0.5 -0.3 -0.2 0.1
EC-6.3.1.1 0.009 208 2.4 -3.1 0.1 -1.0 0.0
EC-6.2.9.1 0.031 208 2.4 -3.1 0.1 -1.0 0.0
EC-6.3.3-661 0.038 208 2.4 -3.1 0.1 -1.0 0.0
EC-6.3.3-662 0.065 208 2.4 -3.1 0.1 -1.0 0.0
EC-6.2.6-(Z) 0.002 204 2.0 0.6 -0.4 0.0 0.0
EC-6.2.6-(Y) 0.021 206 1.1 3.2 0.0 0.0 0.0
EC-6.3.2 LTB 0.040 206 1.2 -3.1 0.0 -1.0 0.0
_________________________
Page 89 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.110 208
3.02 C 0.09 1.71 0.32

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 90 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 205 -1.0 0.5 0.3 -0.2 0.1
EC-6.3.1.1 0.011 208 3.0 2.3 -0.1 -1.4 -0.1
EC-6.2.9.1 0.054 208 3.0 -2.2 0.1 1.7 0.1
EC-6.3.3-661 0.086 208 3.0 -2.2 0.1 1.7 0.1
EC-6.3.3-662 0.110 208 3.0 -2.2 0.1 1.7 0.1
EC-6.2.6-(Z) 0.002 204 1.9 0.5 -0.3 -0.2 -0.1
EC-6.2.6-(Y) 0.015 207 1.8 2.3 0.0 -1.0 0.0
EC-6.3.2 LTB 0.069 207 1.8 -2.3 0.0 1.7 0.0
_________________________
Page 91 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.139 208
3.70 C 0.11 2.17 0.32

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 92 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 205 -0.9 0.4 0.2 -0.3 0.2
EC-6.3.1.1 0.014 208 3.7 1.4 -0.1 -2.0 -0.1
EC-6.2.9.1 0.068 208 3.7 -1.4 0.0 2.2 0.1
EC-6.3.3-661 0.119 208 3.7 -1.4 0.0 2.2 0.1
EC-6.3.3-662 0.139 208 3.7 -1.4 0.0 2.2 0.1
EC-6.2.6-(Z) 0.001 204 2.0 0.4 -0.2 -0.3 -0.2
EC-6.2.6-(Y) 0.010 207 2.5 1.5 0.0 -1.7 0.0
EC-6.3.2 LTB 0.088 207 2.5 -1.4 0.0 2.2 0.0
_________________________
Page 93 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.149 208
4.55 C 0.12 2.29 0.32

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 94 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.001 205 -0.6 0.0 0.1 -0.4 0.2
EC-6.3.1.1 0.017 208 4.5 0.4 0.0 -2.2 -0.1
EC-6.2.9.1 0.072 208 4.6 -0.3 0.0 2.3 0.1
EC-6.3.3-661 0.135 208 4.6 -0.3 0.0 2.3 0.1
EC-6.3.3-662 0.149 208 4.6 -0.3 0.0 2.3 0.1
EC-6.2.6-(Y) 0.003 201 3.8 0.4 0.0 -2.2 0.0
EC-6.3.2 LTB 0.093 207 3.3 -0.3 0.0 2.3 0.0
_________________________
Page 95 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.152 208
5.19 C -0.12 -2.29 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 96 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.3.1.1 0.020 208 5.2 -0.5 0.0 -2.2 -0.1
EC-6.2.9.1 0.072 208 5.2 -0.4 0.0 -2.3 -0.1
EC-6.3.3-661 0.136 208 5.2 -0.4 0.0 -2.3 -0.1
EC-6.3.3-662 0.152 208 5.2 -0.4 0.0 -2.3 -0.1
EC-6.2.6-(Y) 0.003 201 4.5 0.5 0.0 2.1 0.0
EC-6.3.2 LTB 0.093 207 4.0 -0.4 0.0 -2.3 0.0
_________________________
Page 97 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.145 208
5.87 C -0.11 -2.14 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 98 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.3.1.1 0.022 208 5.9 -1.3 0.1 -1.9 -0.1
EC-6.2.9.1 0.067 208 5.9 -1.3 0.0 -2.1 -0.1
EC-6.3.3-661 0.122 208 5.9 -1.3 0.0 -2.1 -0.1
EC-6.3.3-662 0.145 208 5.9 -1.3 0.0 -2.1 -0.1
EC-6.2.5 0.012 203 0.0 -0.2 0.0 -0.4 0.0
EC-6.2.6-(Z) 0.001 204 2.5 0.3 -0.2 0.3 0.2
EC-6.2.6-(Y) 0.009 207 4.7 1.4 0.0 1.7 0.0
EC-6.3.2 LTB 0.086 207 4.6 -1.3 0.0 -2.2 0.0
_________________________
Page 99 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.123 208
6.55 C -0.09 -1.72 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 100 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.3.1.1 0.025 208 6.6 -2.2 0.1 -1.3 -0.1
EC-6.2.9.1 0.054 208 6.6 -2.1 0.1 -1.7 -0.1
EC-6.3.3-661 0.094 208 6.6 -2.1 0.1 -1.7 -0.1
EC-6.3.3-662 0.123 208 6.6 -2.1 0.1 -1.7 -0.1
EC-6.2.6-(Z) 0.002 204 2.6 0.4 -0.3 0.2 0.1
EC-6.2.6-(Y) 0.015 207 5.4 -2.2 0.0 -1.1 0.0
EC-6.3.2 LTB 0.069 207 5.3 -2.2 0.0 -1.7 0.0
_________________________
Page 101 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.085 208
7.41 C -0.05 -1.03 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 102 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.3.1.1 0.028 208 7.4 -3.2 0.2 -0.4 0.0
EC-6.2.9.1 0.032 208 7.4 -3.2 0.1 -1.0 -0.1
EC-6.3.3-661 0.049 208 7.4 -3.2 0.1 -1.0 -0.1
EC-6.3.3-662 0.085 208 7.4 -3.2 0.1 -1.0 -0.1
EC-6.2.6-(Z) 0.002 204 2.9 0.7 -0.4 0.0 0.0
EC-6.2.6-(Y) 0.022 207 6.2 3.3 0.0 0.0 0.0
EC-6.3.2 LTB 0.041 207 6.2 -3.2 0.0 -1.0 0.0
_________________________
Page 103 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.435 208
4.10 C -0.02 16.77 1.56

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 12.500 12.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 104 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 205 -1.2 2.5 0.3 0.0 0.0
EC-6.3.1.1 0.009 208 4.1 14.2 -0.1 0.0 0.0
EC-6.2.9.1 0.271 209 2.2 -7.1 0.2 16.8 0.0
EC-6.3.3-661 0.294 208 4.1 -7.1 -0.1 16.8 0.0
EC-6.3.3-662 0.435 208 4.1 -7.1 -0.1 16.8 0.0
EC-6.2.6-(Z) 0.001 204 2.5 2.5 -0.3 0.0 0.1
EC-6.2.6-(Y) 0.067 201 3.2 14.2 0.0 0.0 0.0
EC-6.3.2 LTB 0.317 201 3.2 -7.1 0.0 16.8 0.0
_________________________
Page 105 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.437 208
3.76 C -0.03 16.87 1.56

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 12.500 12.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 106 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.3.1.1 0.008 208 3.8 14.3 -0.1 0.0 0.0
EC-6.2.9.1 0.273 209 2.6 -7.2 0.2 16.9 0.0
EC-6.3.3-661 0.295 208 3.8 -7.2 -0.1 16.9 0.0
EC-6.3.3-662 0.437 208 3.8 -7.2 -0.1 16.9 0.0
EC-6.2.6-(Z) 0.002 204 1.8 -1.3 -0.3 3.1 -0.1
EC-6.2.6-(Y) 0.067 201 3.2 14.3 0.0 0.0 0.0
EC-6.3.2 LTB 0.319 201 3.2 -7.2 0.0 16.9 0.0
_________________________
Page 107 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.579 208
4.10 C -0.04 22.43 1.56

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 12.500 12.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 108 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 205 -1.2 1.2 0.3 -3.0 -0.1
EC-6.3.1.1 0.009 208 4.1 7.1 -0.1 -16.8 0.0
EC-6.2.9.1 0.362 208 4.1 0.0 -0.2 22.4 0.0
EC-6.3.3-661 0.552 208 4.1 0.0 -0.2 22.4 0.0
EC-6.3.3-662 0.579 208 4.1 0.0 -0.2 22.4 0.0
EC-6.2.6-(Z) 0.001 204 2.5 1.2 -0.3 -3.0 0.1
EC-6.2.6-(Y) 0.033 201 3.2 7.1 0.0 -16.8 0.0
EC-6.3.2 LTB 0.424 201 3.2 0.0 0.0 22.4 0.0
_________________________
Page 109 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.579 208
4.13 C 0.04 -22.43 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 12.500 12.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 110 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 205 -1.2 -0.1 0.3 -4.1 -0.1
EC-6.3.1.1 0.009 208 4.1 -0.1 -0.2 -22.4 0.0
EC-6.2.9.1 0.362 208 4.1 -0.1 -0.2 -22.4 0.0
EC-6.3.3-661 0.552 208 4.1 -0.1 -0.2 -22.4 0.0
EC-6.3.3-662 0.579 208 4.1 -0.1 -0.2 -22.4 0.0
EC-6.2.6-(Z) 0.001 204 2.6 -0.1 -0.3 -4.1 0.1
EC-6.2.6-(Y) 0.034 201 3.2 7.2 0.0 16.8 0.0
EC-6.3.2 LTB 0.424 201 3.2 -0.1 0.0 -22.4 0.0
_________________________
Page 111 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.435 208
4.13 C 0.02 -16.77 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 12.500 12.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 112 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 205 -1.2 -1.4 0.3 -3.0 -0.1
EC-6.3.1.1 0.009 208 4.1 -7.3 -0.1 -16.8 0.0
EC-6.2.9.1 0.271 209 2.2 -7.3 0.2 -16.8 0.0
EC-6.3.3-661 0.294 208 4.1 -7.3 -0.1 -16.8 0.0
EC-6.3.3-662 0.435 208 4.1 -7.3 -0.1 -16.8 0.0
EC-6.2.6-(Z) 0.002 204 2.6 -1.4 -0.3 -3.0 0.1
EC-6.2.6-(Y) 0.067 201 3.2 14.3 0.0 0.0 0.0
EC-6.3.2 LTB 0.317 201 3.2 -7.3 0.0 -16.8 0.0
_________________________
Page 113 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.580 209
4.83 C 0.02 22.43 1.56

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 12.500 12.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 114 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.003 204 -2.7 1.2 -0.3 -3.1 0.1
EC-6.3.1.1 0.011 209 4.8 7.0 0.2 -16.9 0.0
EC-6.2.9.1 0.361 208 1.5 0.1 -0.2 22.4 0.0
EC-6.3.3-661 0.554 209 4.8 0.1 0.1 22.4 0.0
EC-6.3.3-662 0.580 209 4.8 0.1 0.1 22.4 0.0
EC-6.2.6-(Z) 0.002 204 -2.7 1.2 -0.3 -3.1 0.1
EC-6.2.6-(Y) 0.033 201 3.2 7.0 0.0 -16.9 0.0
EC-6.3.2 LTB 0.424 201 3.2 0.1 0.0 22.4 0.0
_________________________
Page 115 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.580 209
4.83 C -0.02 -22.43 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 12.500 12.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 116 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.003 204 -2.7 -0.1 -0.3 -4.1 0.1
EC-6.3.1.1 0.011 209 4.8 -0.1 0.1 -22.4 0.0
EC-6.2.9.1 0.361 208 1.5 -0.1 -0.2 -22.4 0.0
EC-6.3.3-661 0.554 209 4.8 -0.1 0.1 -22.4 0.0
EC-6.3.3-662 0.580 209 4.8 -0.1 0.1 -22.4 0.0
EC-6.2.6-(Z) 0.001 204 -2.7 -0.1 -0.3 -4.1 0.1
EC-6.2.6-(Y) 0.034 201 3.2 7.2 0.0 16.9 0.0
EC-6.3.2 LTB 0.424 201 3.2 -0.1 0.0 -22.4 0.0
_________________________
Page 117 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.437 208
3.70 C 0.03 -16.87 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 12.500 12.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 118 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.3.1.1 0.008 208 3.7 -7.3 -0.1 -16.9 0.0
EC-6.2.9.1 0.273 209 2.7 -7.3 0.2 -16.9 0.0
EC-6.3.3-661 0.295 208 3.7 -7.3 -0.1 -16.9 0.0
EC-6.3.3-662 0.437 208 3.7 -7.3 -0.1 -16.9 0.0
EC-6.2.6-(Z) 0.002 204 1.7 -1.5 -0.3 -3.1 0.1
EC-6.2.6-(Y) 0.068 201 3.2 14.4 0.0 0.0 0.0
EC-6.3.2 LTB 0.319 201 3.2 -7.3 0.0 -16.9 0.0
_________________________
Page 119 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.1.1 0.008 204
0.59 C 0.00 0.00 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 2.000 2.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 120 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.004 205 -0.6 0.0 0.0 0.0 0.0
EC-6.3.1.1 0.008 204 0.6 0.0 0.0 0.0 0.0
_________________________
Page 121 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.1.1 0.007 205
0.57 C 0.00 0.00 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 2.000 2.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 122 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.004 204 -0.6 0.0 0.0 0.0 0.0
EC-6.3.1.1 0.007 205 0.6 0.0 0.0 0.0 0.0
_________________________
Page 123 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.1.1 0.008 204
0.59 C 0.00 0.00 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 2.000 2.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 124 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.004 205 -0.6 0.0 0.0 0.0 0.0
EC-6.3.1.1 0.008 204 0.6 0.0 0.0 0.0 0.0
_________________________
Page 125 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.1.1 0.148 205
4.06 C 0.00 0.00 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 2.000 2.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 126 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.027 204 -4.0 0.0 0.0 0.0 0.0
EC-6.3.1.1 0.148 205 4.1 0.0 0.0 0.0 0.0
_________________________
Page 127 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.1.1 0.051 204
1.40 C 0.00 0.00 0.00

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 2.000 2.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 128 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.009 205 -1.4 0.0 0.0 0.0 0.0
EC-6.3.1.1 0.051 204 1.4 0.0 0.0 0.0 0.0
_________________________
Page 129 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.1.1 0.048 204
1.32 C 0.00 0.00 1.85

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 2.000 2.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 130 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.009 205 -1.3 0.0 0.0 0.0 0.0
EC-6.3.1.1 0.048 204 1.3 0.0 0.0 0.0 0.0
_________________________
Page 131 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.1.1 0.146 205
3.99 C 0.00 0.00 1.86

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 2.000 2.000

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 132 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.027 204 -4.0 0.0 0.0 0.0 0.0
EC-6.3.1.1 0.146 205 4.0 0.0 0.0 0.0 0.0
_________________________
Page 133 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.066 209
2.56 C -0.06 0.99 0.32

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 134 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.003 204 -1.5 0.6 -0.4 0.0 0.0
EC-6.3.1.1 0.010 209 2.5 3.1 0.2 -0.6 0.0
EC-6.2.9.1 0.032 208 0.6 -3.1 0.1 1.0 0.1
EC-6.3.3-661 0.039 209 2.6 -3.1 -0.1 1.0 -0.1
EC-6.3.3-662 0.066 209 2.6 -3.1 -0.1 1.0 -0.1
EC-6.2.6-(Z) 0.003 204 -1.5 0.6 -0.4 0.0 0.0
EC-6.2.6-(Y) 0.021 207 1.1 3.2 0.0 0.0 0.0
EC-6.3.2 LTB 0.040 207 1.1 -3.1 0.0 1.0 0.0
_________________________
Page 135 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

PASS EC-6.3.3-662 0.065 208
2.33 C 0.06 0.99 0.32

=======================================================================
MATERIAL DATA

z-axis y-axis
Shear Area : 10.000 8.250

GM0 : 1.00 GM1 : 1.00 GM2 : 1.25
z-axis y-axis

Page 136 of 140
Monday, July 10, 2017, 07:51 PM

FX MY MZ LOCATION
=======================================================================

EC-6.2.3 (T) 0.002 205 -1.1 0.6 0.4 0.0 0.0
EC-6.3.1.1 0.009 208 2.3 3.1 -0.2 -0.6 0.0
EC-6.2.9.1 0.032 208 2.3 -3.1 0.1 1.0 0.1
EC-6.3.3-661 0.038 208 2.3 -3.1 0.1 1.0 0.1
EC-6.3.3-662 0.065 208 2.3 -3.1 0.1 1.0 0.1
EC-6.2.6-(Z) 0.003 204 1.8 0.6 -0.4 0.0 0.0
EC-6.2.6-(Y) 0.021 207 1.1 3.2 0.0 0.0 0.0
EC-6.3.2 LTB 0.040 207 1.1 -3.1 0.0 1.0 0.0
_________________________
************** END OF TABULATED RESULT OF DESIGN **************
149. STEEL MEMBER TAKE OFF ALL
Page 137 of 140
Monday, July 10, 2017, 07:51 PM
STEEL TAKE-OFF
--------------
PROFILE LENGTH(METE) WEIGHT(KN )
ST CH100X50X10 2.00 0.200

ST CH150X75X18 16.58 2.904
ST UA50X50X6 13.25 0.579
ST CH200X75X23 12.50 2.871
----------------
TOTAL = 6.554
MEMBER PROFILE LENGTH WEIGHT

(METE) (KN )
7 ST CH100X50X10 0.50 0.050

8 ST CH100X50X10 0.50 0.050
43 ST CH150X75X18 0.50 0.088
44 ST CH150X75X18 0.50 0.088
45 ST CH150X75X18 0.50 0.088
46 ST CH150X75X18 0.50 0.088
52 ST CH150X75X18 1.10 0.193
53 ST CH150X75X18 1.10 0.193
54 ST CH150X75X18 1.10 0.193
55 ST CH150X75X18 1.10 0.193
58 ST CH100X50X10 0.50 0.050
59 ST CH100X50X10 0.50 0.050
61 ST UA50X50X6 0.71 0.031
62 ST UA50X50X6 0.71 0.031
65 ST UA50X50X6 0.71 0.031
66 ST UA50X50X6 0.71 0.031
68 ST CH150X75X18 0.32 0.056
72 ST CH150X75X18 0.32 0.056
75 ST CH150X75X18 0.32 0.056
76 ST CH150X75X18 0.32 0.056
77 ST CH150X75X18 0.32 0.056
78 ST CH150X75X18 0.32 0.056
79 ST CH150X75X18 0.32 0.056
80 ST CH150X75X18 0.32 0.056
81 ST CH150X75X18 0.32 0.056
82 ST CH150X75X18 0.32 0.056
83 ST CH150X75X18 0.32 0.056
84 ST CH150X75X18 0.32 0.056
85 ST CH150X75X18 0.32 0.056
86 ST CH150X75X18 0.32 0.056
87 ST CH150X75X18 0.32 0.056
88 ST CH150X75X18 0.32 0.056
89 ST CH150X75X18 0.32 0.056
90 ST CH150X75X18 0.32 0.056
91 ST CH150X75X18 0.32 0.056
92 ST CH150X75X18 0.32 0.056
93 ST CH150X75X18 0.32 0.056
Page 138 of 140
Monday, July 10, 2017, 07:51 PM
94 ST CH150X75X18 0.32 0.056

95 ST CH150X75X18 0.32 0.056
96 ST CH150X75X18 0.32 0.056
97 ST CH150X75X18 0.32 0.056
98 ST CH150X75X18 0.32 0.056
99 ST CH150X75X18 0.32 0.056
100 ST CH150X75X18 0.32 0.056
101 ST CH150X75X18 0.32 0.056
102 ST CH150X75X18 0.32 0.056
103 ST CH200X75X23 1.56 0.359
104 ST CH200X75X23 1.56 0.359
105 ST CH200X75X23 1.56 0.359
106 ST CH200X75X23 1.56 0.359
107 ST CH200X75X23 1.56 0.359
108 ST CH200X75X23 1.56 0.359
109 ST CH200X75X23 1.56 0.359
110 ST CH200X75X23 1.56 0.359
111 ST UA50X50X6 1.00 0.044
112 ST UA50X50X6 1.00 0.044
113 ST UA50X50X6 1.00 0.044
114 ST UA50X50X6 1.85 0.081
115 ST UA50X50X6 1.86 0.081
116 ST UA50X50X6 1.85 0.081
117 ST UA50X50X6 1.86 0.081
118 ST CH150X75X18 0.32 0.056
119 ST CH150X75X18 0.32 0.056
----------------
TOTAL = 6.554
************ END OF DATA FROM INTERNAL STORAGE ************
150. FINISH
*********** END OF THE STAAD.Pro RUN ***********
**** DATE= JUL 3,2017 TIME= 17:29:16 ****
Page 139 of 140
Monday, July 10, 2017, 07:51 PM
************************************************************
* For questions on STAAD.Pro, please contact *
* Bentley Systems or Partner offices *
* *
* Telephone Web / Email *
* USA +1 (714) 974-2500 *
* UK +44 (0) 808 101 9246 *
* SINGAPORE +65 6225-6158 *
* FRANCE +33 (0) 1 55238400 *
* GERMANY +49 0931 40468 *
* INDIA +91 (033) 4006-2021 *
* JAPAN +81 (03)5952-6500 http://www.ctc-g.co.jp *
* CHINA +86 21 6288 4040 *
* THAILAND +66 (0)2645-1018/19 [email protected]*
* *
* Worldwide http://selectservices.bentley.com/en-US/ *
* *
************************************************************
Page 140 of 140

LC161076 MTKF 1 12 0001 PDF

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

LC161076 MTKF 1 12 0001 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LC161076 MTKF 1 12 0001 PDF

Uploaded by

Copyright:

Available Formats

`

EPIC OF WALKOVER BRIDGES IN TANK-FARM AREA,

PROJECT NO: LC161076

A 10/07/2017 APPROVED FOR CONSTRUCTION DJ DS RH

1 12/06/2017 ISSUED FOR APPROVAL DJ DS RH

0 01/06/2017 ISSUED FOR COMMENTS DJ DS RH

Prepared Checked Approved Approved

2 BASIC DATA ................................................................................ 5

3 REFERENCE DOCUMENTS ........................................................ 5

5 LOAD COMBINATIONS ............................................................. 11

6 ANALYSIS & DESIGN ................................................................ 11

7 CONNECTION DESIGN ............................................................. 22

8 BASE PLATE & ANCHOR BOLT DESIGN................................ 25

9 FOUNDATION DESIGN ............................................................. 29

ATTACHMENT - A ................................................................................ 36

Doc No: LC161076-MTKF-1-12-0001 Rev.A Page 2 of 36

Shall The word "shall" is to be understood as mandatory.

Should The word "should" is to be understood as being

May The word "may" is used where alternatives are equally

Must The word "must" is used where a provision is a

Client / Company Qatar Petroleum

Contractor Company / Firm or Party appointed by QP to perform

Manufacturer The Party that manufactures, fabricates or produces

Supplier Company / Firm or Party appointed by QP to supply

Doc No: LC161076-MTKF-1-12-0001 Rev.A Page 3 of 36

Doc No: LC161076-MTKF-1-12-0001 Rev.A Page 4 of 36

Quantity Unit Nomenclature

Doc No: LC161076-MTKF-1-12-0001 Rev.A Page 5 of 36

RP.5914.D.00.1400.02 Soil and Foundations

3.2 INTERNATIONAL CODES & STANDARDS

BCSA guidelines National Structural Steelwork Specification (British

BS 8110 Design and Construction of Reinforced concrete

BS EN 197 (All parts) Cement. Composition, specifications and conformity

BS 4466 Scheduling, dimensioning, bending and cutting of steel

BS 4483 Specification for steel fabric for the reinforcement of

Doc No: LC161076-MTKF-1-12-0001 Rev.A Page 6 of 36

BS 5395 Parts 1 to 3 Stairs, ladders and walkways

3.3.1 GRADE OF CONCRETE

3.3.2 CONCRETE REINFORCEMENT STEEL

3.3.3 STRUCTURAL STEEL

4.1 DEAD LOADS (DL)

Doc No: LC161076-MTKF-1-12-0001 Rev.A Page 7 of 36

Following Unit weights have been considered in calculating self-weight of structure.

Structural Steel = 78.5 kN/m3

Reinforced Concrete = 25 kN/m3 (for substructure design)

Soil = 18 kN/m3 (for substructure design)

Self-weight of 30 mm thick grating = 0.385 kN/m2

Platform Width =1m

Width of grating supported on each side of beam = 1/2 = 0.5 m

Load on beam due to grating (half width) = 0.5 x 0.385

Size of one stair tread = 1 m x0.25 m

Steps Load due to grating = 1.0 x 0.25 x 0.385

No. of support point =2

Load on each support point = 0.1 / 2

Weight of Handrail = 5.34 kg\m = 0.0534 kN/m

Weight of vertical leg = 6.4Kg/m = 0.064 kN/m

Weight of mid rail = 4.6Kg/m = 0.046 kN/m

Doc No: LC161076-MTKF-1-12-0001 Rev.A Page 8 of 36