Servostar CD Install PDF

KOLLMORGEN
www.DanaherMotion.com
SERVOSTAR® CD
Installation Manual
M-SS-017-01 Rev. T
Firmware Version 6.3.3
Solutions by
D A N A H E R
M O T IO N
Version History
Revision Date Description of Revision
0 -- Preliminary issue for review
1 01/05/98 Initial release of UCB hardware
2 03/13/98 Added UCB features
3 09/18/98 Cx and UCB position capability (restructure document)
4 12/03/98 Additional position features added
5 05/01/99 Restructured SERCOS interface, CD-ROM transition
6 09/15/99 Appendix A and B added, sine encoder features, Cx10 added
7 06/30/00 Added information on Firmware upgrade
8 10/10/00 Corrected specifications, added clarification
9 02/01/01 Corrected Electrical Specs and wiring diagrams (restructure document)
10 02/28/01 Added information for Firmware upgrade
11 09/28/01 Corrected Wiring Diagrams, errors in commands, and EMI filter info
12 01/16/02 Corrected Outline Dimensions for Cx units and all wiring diagrams
13 03/27/02 Corrected Model Numbers and added Danaher information
14 06/14/02 Added Appendix C
15 07/10/02 Added Appendix D, clarified digital and sine encoder specifications
16 11/22/02 Standardized units of measure
17 12/16/02 Updated encoder phasing and added IP 30-30 information
18 02/14/03 Corrected Sx Hardware Specifications
19 04/18/03 Added extended I/O information for Series 5
T 09/03/04 Separated SERVOSTAR-S from SERVOSTAR-CD, updated corporate
identity, added Series 5 capabilities, updated appendixes.
VGA® and PC-AT® are registered trademarks of International Business Machines Corporation.
Windows®95/98 and Windows NT® are registered trademarks of Microsoft Corporation. ENDAT® is a
registered trademark of Dr. Johannes Heidenhain GmbH
GOLDLINE®, SILVERLINE®, MOTIONEERING®, MOTIONLINK®, PLATINUM®, and SERVOSTAR®
are registered trademarks of Danaher Motion.
© Copyright 2000 - 2004 Danaher Motion - All rights reserved.

Printed in the United States of America.
NOTICE:
DANAHER MOTION is a registered trademark of Danaher Corporation. Danaher Motion makes every
attempt to ensure accuracy and reliability of the specifications in this publication. Specifications are
subject to change without notice. Danaher Motion provides this information "AS IS" and disclaims all
warranties, express or implied, including, but not limited to, implied warranties of merchantability and
fitness for a particular purpose. It is the responsibility of the product user to determine the suitability of
this product for a specific application.
Alerts you to potential physical danger or harm. Failure to follow

warning notices could result in personal injury or death.
WARNING
Directs attention to general precautions, which if not followed,

could result in personal injury and/or equipment damage.
CAUTION
Highlights information critical to your understanding or use of the

product.
NOTE
Safety Instructions
Only qualified personnel are permitted to transport, assembly, commission, and
maintenance this equipment. Properly qualified personnel are persons who are familiar with
the transport, assembly, installation, commissioning and operation of motors, and who have
the appropriate qualifications for their jobs. The qualified personnel must know and observe
the standards and regulations of IEC 364 resp. CENELEC HD 384 or DIN VDE 0100 IEC
report 664 or DIN VDE 0110 National regulations for safety and accident prevention or
VBG 4
− Read all available documentation before assembly and commissioning. Incorrect
handling of products in this manual can result in injury and damage to persons and
machinery. Strictly adhere to the technical information on the installation requirements.
− It is vital to ensure that all system components are connected to earth ground.
Electrical safety is impossible without a low-resistance earth connection.
®
− The SERVOSTAR product contains electro-statically sensitive components that can
be damaged by incorrect handling. Discharge yourself before touching the product.
Avoid contact with high insulating materials (artificial fabrics, plastic film, etc.). Place
the product on a conductive surface.
− During operation keep all covers and cabinet doors shut. Otherwise, there are deadly
hazards that could possibility cause severe damage to health or the product.
− During operation, depending on the degree of enclosure protection, the product can
have bare components that are live or have hot surfaces. Control and power cables
can carry high voltage even when the motor is not rotating.
− Never pull out or plug in the product while the system is live. There is a danger of
electric arcing and danger to persons and contacts.
− After powering down the product, wait at least ten minutes before touching live
sections of the equipment or undoing connections (e.g., contacts, screwed
connections). Capacitors can store dangerous voltages for long periods of time after
power has been switched off. To be safe, measure the contact points with a meter
before touching.
When alert symbols are seen in this manual, be alert to the potential for personal injury.
Follow the recommended precautions and safe operating practices included with the alert
symbols. Safety notices in this manual provide important information. Read and be familiar
with these instructions before attempting installation, operation, or maintenance. The
purpose of this section is to alert users to possible safety hazards associated with this
equipment and the precautions that need to be taken to reduce the risk of personal injury
and damage to the equipment. Failure to observe these precautions could result in serious
bodily injury, damage to the equipment, or operational difficulty.
Directives and Standards
The SERVOSTAR CD product series have been successfully tested and evaluated to meet
UL/cUL 508C for both U.S. and Canadian markets. This standard describes the fulfillment
by design of minimum requirements for electrically operated power conversion equipment,
such as frequency converters and servo amplifiers, which is intended to eliminate the risk
of fire, electric shock, or injury to persons, being caused by such equipment.
CE Mark Conformance
Servo drives are components that are intended to be incorporated into electrical plant and
machines for industrial use. When the servo drives are built into machines or plants, drives
cannot be operated until the machine or plant fulfills the requirements of the EC Directive
on Machines 89/392/EEC and the EC Directive on EMC (89/336/EEC). EN 60204 and EN
292 must also be observed.
In connection with the Low Voltage Directive 73/23/EEC, the harmonized standards of the
EN 50178 series are applied to the amplifiers, together with EN 60439-1, EN 60146 and EN
60204.
The manufacturer of the machine or plant is responsible for ensuring that they meet the
limits required by the EMC regulations. Advice on the correct installation for EMC - such as
shielding, grounding, arrangement of filters, treatment of connectors and the laying out of
cabling - can be found within this documentation.
Conformance with the EC Directive on EMC 89/336/EEC and the Low Voltage Directive
73/23/EEC is mandatory for the supply of servo drives within the European Community.
An authorized testing laboratory in a defined configuration with the system components has
tested the servo drives. Any divergence from the configuration and installation described in
this documentation means that you are responsible for the performance of new
measurements to ensure that the regulatory requirements are met.
Danaher Motion Kollmorgen’s SERVOSTAR CD Series drives and systems have been
successfully tested and evaluated to the limits and requirements of the EC Directive on
EMC (89/336/EEC) and the EC Directive on Low Voltage (72/73/EEC). The product lines
have been evaluated to EN50178 and EN60204 as a component of a machine and other
relevant standards.
The EMC of a system can be identified by emissions and immunity. Emissions refer to the
generation of EMI (electromagnetic interference) and immunity refers to the susceptibility
levels of the equipment. Limits were derived from generic standards EN55081-2 and
EN55082-2 for heavy industrial environments. The SERVOSTAR CD series of drives have
been tested for radiated emissions, conducted emissions, EFT, ESD, surge, conducted
immunity, and radiated immunity. These tests have been done in accordance with
EN55011, EN61000-4-2, ENV50140, IEC 1000-4-4, EN61000-4-5, and ENV50141.
Installation of the equipment is critical in designing for system and machine
electromagnetic compatibility (EMC). You must apply the installation
recommendations and the CE filtering practices when mounting and installing the
drive system for CE conformance.
Danaher Motion Kollmorgen 06/04 Table of Contents
Table of Contents
1 INTRODUCTION...........................................................................................................1
1.1 UCB2 DIGITAL CONTROL BOARD ..................................................................................... 1
1.2 NEW FEATURES .................................................................................................................. 2
2 READ BEFORE INSTALLING .....................................................................................1
2.1 USE AS DIRECTED .............................................................................................................. 2
3 UNPACKING AND INSPECTING.................................................................................3
3.1 NEW DESCRIPTION LABEL ................................................................................................. 3
3.2 SERIES 5 PART NUMBER GUIDE ......................................................................................... 3
3.3 SERIES 2 MODEL NUMBERS ............................................................................................... 4
4 MOUNTING...................................................................................................................5
4.1 HARDWARE SPECIFICATIONS ............................................................................................. 5
4.2 CONTROL SPECIFICATIONS ................................................................................................. 5
4.3 OUTLINE DIMENSIONS ........................................................................................................ 6
5 WIRING.........................................................................................................................7
5.1 ENCLOSURE ........................................................................................................................ 7
5.2 GROUNDING ........................................................................................................................ 8
5.3 BONDING ............................................................................................................................ 8
5.3.1 Non-insulated Cable Clamp........................................................................................ 9
5.3.2 Alternative Bonding Methods ..................................................................................... 9
5.4 CE FILTERING TECHNIQUES............................................................................................. 10
5.4.1 Input Power Filtering................................................................................................ 11
5.4.2 Motor Line Filtering ................................................................................................. 12
5.4.3 I/O Filtering .............................................................................................................. 13
5.4.4 Filter and Bonding Diagram .................................................................................... 14
5.5 SYSTEM INTERCONNECT .................................................................................................. 15
5.5.1 Electrical Specifications ........................................................................................... 16
5.5.2 Regen Information..................................................................................................... 17
5.5.3 Mating Connectors.................................................................................................... 17
5.5.4 Kit Parts and Models ................................................................................................ 18
5.6 WIRING DIAGRAMS .......................................................................................................... 18
5.6.1 Top View.................................................................................................................... 18
5.6.2 Connector Pin-Out for C-9 ....................................................................................... 19
5.6.3 Making Connections to C-9 ...................................................................................... 19
5.6.4 Wiring Diagram Notes .............................................................................................. 19
5.6.5 Front View................................................................................................................. 20
5.6.6 C1 Communications Port.......................................................................................... 20
5.6.10 Main Input Power Connections ................................................................................ 22
5.6.11 C8 Remote Encoder Input......................................................................................... 22
5.7 PINOUT CONNECTORS ...................................................................................................... 23
5.8 SYSTEM FEEDBACK .......................................................................................................... 25
5.8.1 Resolver..................................................................................................................... 25
5.8.2 Resolver Feedback Diagram..................................................................................... 25
5.8.2.1 Specifications .................................................................................................... 26
5.8.2.2 Cable Lengths ................................................................................................... 26
5.8.2.3 Resolution and Accuracy .................................................................................. 26
5.8.3 Digital Encoder......................................................................................................... 27
5.8.3.1 Specifications .................................................................................................... 27
5.8.3.2 Cable Lengths ................................................................................................... 28
5.8.4 Sine Encoder ............................................................................................................. 28
SERVOSTAR CD Installation M-SS-017-01 Rev. T i

Table of Contents 06/04 Danaher Motion Kollmorgen
5.8.5 Sine Encoder Feedback Diagram ............................................................................. 30
5.8.5.1 Specifications .................................................................................................... 31
5.8.5.2 Cable Lengths.................................................................................................... 31
5.9 ENCODER EQUIVALENT OUTPUT ...................................................................................... 32
5.9.1 Resolver Systems ....................................................................................................... 32
5.9.2 Encoder Systems........................................................................................................ 32
5.9.3 Sine-encoder Systems ................................................................................................ 32
5.9.4 EEO Phasing ............................................................................................................. 33
5.9.4.1 Resolver Systems .............................................................................................. 33
5.9.4.2 Encoder and Sine-encoder Systems .................................................................. 33
5.9.5 Recommended Manufacturers’ List .......................................................................... 34
6 SYSTEM COMMUNICATION .....................................................................................35
6.1 COMPUTER REQUIREMENTS ............................................................................................. 35
6.2 DRIVE COMMUNICATION .................................................................................................. 36
6.2.1 RS-232-A Connection................................................................................................ 36
6.2.2 RS-485 Connection.................................................................................................... 37
6.2.3 Setting Drive Address................................................................................................ 37
6.3 SENDING/RETRIEVING SYSTEM DATA ............................................................................. 38
6.4 MOTIONLINK INSTALLATION ....................................................................................... 38
6.4.1 Running the Program................................................................................................ 38
6.5 USING MOTIONLINK ..................................................................................................... 39
6.5.1 MOTIONLINK Startup Wizard ................................................................................. 39
6.5.2 Main MOTIONLINK Screen ..................................................................................... 41
6.5.3 Terminal Mode .......................................................................................................... 42
6.6 MULTIDROP COMMUNICATION ........................................................................................ 43
6.7 POWER-UP SEQUENCE ...................................................................................................... 44
6.8 ENABLING THE SYSTEM.................................................................................................... 44
7 SERCOS INTERFACE SETUP...................................................................................45
7.1 DIP SWITCH CONFIGURATION ......................................................................................... 45
7.1.1 Setting Drive Address................................................................................................ 45
7.1.2 Setting Transmission Power Levels .......................................................................... 45
7.2 STATUS DISPLAY .............................................................................................................. 46
7.3 CONNECTION .................................................................................................................... 47
7.4 COMMUNICATION ............................................................................................................. 47
7.4.1 Drive Configuration .................................................................................................. 48
7.4.2 CP Run-Up ................................................................................................................ 48
7.4.2.1 CP2 Initialization .............................................................................................. 49
7.4.2.2 CP3 Initialization .............................................................................................. 49
7.4.2.3 Operational Notes.............................................................................................. 49
7.4.2.4 Equation Notes .................................................................................................. 50
8 SYSTEM OPERATION ...............................................................................................51
8.1 OPERATIONAL MODES ...................................................................................................... 51
8.2 SYSTEM I/O....................................................................................................................... 52
8.2.1 Extended I/O.............................................................................................................. 52
8.2.2 Analog Input (ANIN) ................................................................................................. 53
8.2.3 Remote Enable Input (REMOTE) ............................................................................. 54
8.2.4 Configurable Inputs (IN1, IN2, IN3)......................................................................... 54
8.2.5 Configurable Outputs (ANOUT, O1) ........................................................................ 54
8.2.6 Fault Output Relay (RELAY, RELAYMODE)........................................................... 55
8.2.7 Motor Thermostat Input ............................................................................................ 55
8.3 CONTROL LOOPS ............................................................................................................... 55
8.3.1 Core Processors ........................................................................................................ 55
8.3.2 Servo Loop Description............................................................................................. 56
8.3.2.1 Current Loop ..................................................................................................... 56
8.3.2.2 Commutation Loop ........................................................................................... 57
8.3.2.3 Velocity Loop.................................................................................................... 57
ii M-SS-017-01 Rev. T SERVOSTAR CD Installation

Danaher Motion Kollmorgen 06/04 Table of Contents
8.3.2.4 Position Loop .................................................................................................... 57
8.3.3 Torque Loop Operation ............................................................................................ 58
8.3.3.1 Serial Torque..................................................................................................... 58
8.3.3.2 Analog Torque .................................................................................................. 59
8.3.4 Current Sampling...................................................................................................... 60
8.4 FOLDBACK ........................................................................................................................ 61
8.4.1 Drive FoldBack ......................................................................................................... 61
8.4.2 Motor FoldBack ........................................................................................................ 61
8.5 ENCODER SIMULATION .................................................................................................... 62
8.6 ENCODER INITIALIZATION ................................................................................................ 62
8.6.1 The Process ............................................................................................................... 63
8.7 SINE/COSINE CALIBRATION ............................................................................................. 63
8.7.1 The Process ............................................................................................................... 64
8.8 SOFTWARE RESOLVER INTERFACE .................................................................................. 64
8.8.1 The Process ............................................................................................................... 64
9 SYSTEM DESCRIPTION............................................................................................65
9.1 PRODUCT FEATURES ........................................................................................................ 65
9.1.1 Current/Torque Control............................................................................................ 65
9.1.2 Velocity Control ........................................................................................................ 65
9.1.3 Position Control........................................................................................................ 66
9.1.4 Profile Ramping Control........................................................................................... 67
9.1.5 Motor Controllability................................................................................................ 67
9.1.6 Feedback Devices ..................................................................................................... 68
9.1.6.1 Resolvers ........................................................................................................... 68
9.1.7 Encoders.................................................................................................................... 68
9.1.7.1 Sine Encoders.................................................................................................... 68
9.1.8 System Communication ............................................................................................. 69
9.1.9 MOTIONLINK Software Environment ..................................................................... 70
9.1.10 Monitoring and Troubleshooting Tools.................................................................... 70
9.1.11 Fault and Safety Detection........................................................................................ 71
9.1.12 General...................................................................................................................... 72
10 TROUBLESHOOTING................................................................................................73
10.1 TROUBLESHOOTING TOOLS .............................................................................................. 73
10.2 ERROR CODES................................................................................................................... 74
10.2.1 FATAL FAULT ERROR CODES .............................................................................. 74
10.2.2 NON-FATAL ERROR CODES.................................................................................. 75
10.2.3 NO MESSAGE FAULTS ........................................................................................... 77
10.3 FAULT MONITORING SYSTEM .......................................................................................... 77
10.4 FIRMWARE UPGRADES ..................................................................................................... 80
10.4.1 Upgrade Procedures ................................................................................................. 80
APPENDIX A .......................................................................................................................83
A.1 MOTOR PINOUTS .............................................................................................................. 83
A.2 SYSTEM CONNECTION DIAGRAM ..................................................................................... 86
APPENDIX B .......................................................................................................................87
B.1 DIGITAL INCREMENTAL ENCODER TYPES ....................................................................... 87
B.1.1 Encoder Basics: A Review ........................................................................................ 87
B.1.2 SERVOSTAR Encoder Types .................................................................................... 90
B.1.2.1 MENCTYPE 0 .................................................................................................. 91
B.1.2.2 MENCTYPE 1 .................................................................................................. 92
B.1.2.3 MENCTYPE 2 .................................................................................................. 92
B.1.2.4 MENCTYPE 3 .................................................................................................. 92
B.1.2.5 MENCTYPE 4 .................................................................................................. 93
B.1.2.6 MENCTYPE 5 .................................................................................................. 94
B.1.2.7 MENCTYPE 6 .................................................................................................. 94
B.1.3 Commutation Accuracy............................................................................................. 94
B.1.4 Physical Encoder Alignment..................................................................................... 95
B.1.5 MECNOFF................................................................................................................ 95
SERVOSTAR CD Installation M-SS-017-01 Rev. T iii
Table of Contents 06/04 Danaher Motion Kollmorgen
B.1.6 System Phasing.......................................................................................................... 96
B.1.7 Troubleshooting ........................................................................................................ 97
B.1.7.1 Line Drivers, Receivers, and Terminations ...................................................... 97
B.1.8 Design Considerations .............................................................................................. 98
B.1.9 Reference Variables .................................................................................................. 98
B.1.10 Example ..................................................................................................................... 99
B.2 RESISTIVE REGENERATION ............................................................................................. 100
APPENDIX C .....................................................................................................................101
C.1 BASIC THEORY OF OPERATION ...................................................................................... 101
C.2 SIGNAL TYPES AND CONNECTIONS ................................................................................ 102
C.2.1 Pulse/Direction Counter ......................................................................................... 102
C.2.2 Up/Down Counter ................................................................................................... 103
C.2.3 Encoder Follower.................................................................................................... 103
C.3 ELECTRONIC GEARING ................................................................................................... 103
C.3.1 Mode of Operation .................................................................................................. 103
C.3.2 Gear Ratio ............................................................................................................... 104
C.3.3 Disabling Gearing................................................................................................... 104
C.3.4 Masking ................................................................................................................... 105
C.3.5 Following Accuracy ................................................................................................ 105
C.3.6 Homing .................................................................................................................... 106
C.4 EXAMPLES ...................................................................................................................... 107
C.4.1 Pulse / Direction...................................................................................................... 107
C.4.2 Encoder Follower.................................................................................................... 107
iv M-SS-017-01 Rev. T SERVOSTAR CD Installation

Danaher Motion Kollmorgen 06/04 Introduction
1 INTRODUCTION
The CD-series of servo motor drive amplifiers, introduced in 1997,
has been very successful and well adopted by our customer base.
Having adopted the general family name of CD Series 2, it is
denoted by model numbers having a 2 as the fifth digit (i.e.,
CR06250). In 2003 a newer version offering more features was
introduced and is known as the CD Series 5. The CD Series 5 is
denoted by model numbers having a 5 as the fifth digit (i.e.
CR06550). The CD Series 5 has been proven to be backward
compatible to the CD Series 2 in form, fit, and function and is the
product of choice for new applications. The CD Series 5 uses the
same field-proven power stage of the CD Series 2, but adds new
DSP control technology, some additional I/O, and lower cost
topology for resolver conversion. Component shortages for the sine
encoder version of the CD Series 2 (i.e., CB06250) have forced the
obsolescence of the CD Series 2 version. This manual has been
rewritten to integrate the features of the new CD Series 5 product.
1.1 UCB2 Digital Control Board

The SERVOSTAR® servo amplifiers incorporate a number of
additional features in the Series 5 model. The addition of these
features is possible due to an upgrade to the UCB2 digital control
board.
SERVOSTAR CD Installation M-SS-017-01 Rev. T 1

Introduction 06/04 Danaher Motion Kollmorgen
1.2 New Features

Feature Description
Sine encoder feedback is supported on
Sine encoder the main control board. Interpolation level
is set up to 4096 (MSININT).
Sine encoder signals are calibrated in
Sine encoder calibration order to increase the accuracy of the
interpolation (SININIT).
Stegmann Hiperface Support Hiperface (Stegmann) interface.
MENCTYPE=10.
SERCOS interface level-A compliance is
implemented.
SERCOS
All serial commands are supported by
SERCOS IDNs.
Encoder simulation Pulse up/pulse down mode for encoder
simulation added with ENCOUTMOD.
For feedback devices without an
absolute position indication, a zero
Encoder initialization motion encoder initialization process is
supported (Wake-no-Shake encoder
initialization process).
The resolver-to-digital (RDC) conversion
Software Resolver is accomplished in the Series 5 products
using software techniques.
Extended I/O Additional I/O.
2 M-SS-017-01 Rev. T SERVOSTAR CD Installation

Danaher Motion Kollmorgen 06/04 Read Before Installing
2 READ BEFORE INSTALLING

These installation steps are designed to lead you through the
®
proper installation and setup of a SERVOSTAR CD system. They
were developed with the assumption that you have a fundamental
understanding of basic electronics, computers, mechanics, and
proper safety practices. However, you do not have to be an expert
in motion control to install and operate the drive system. It is
recommended that you read the entire manual completely before
attempting installation or operation.
High voltage can present dangerous and hazardous
conditions if not performed by a qualified
electrician. Be certain to follow all national and local
codes during installation. Follow all safety
CAUTION precautions outlined in the accompanying CD-ROM
documentation.
1. Open the box(es) and remove all the contents. Check to
ensure there is no visible damage to any of the equipment.
2. Mount the SERVOSTAR CD to the back panel. Refer to the
appropriate Outline Dimensions in this manual. Metal-to-metal
contact is important for electrical noise control!
3. Wire the SERVOSTAR CD according to the Wiring Diagram.
4. Connect solid earth ground to frames of all components.
5. Wire the main power (115/230 VAC).
6. For CDxx560 and CDxx551 product wire the 24 volt supply to
the connector at the top of the drive.
7. Wire user I/O at connector C3: At a minimum, 24 volts must be
brought in to the enable circuit. Be certain that connector C3 is
inserted correctly.
8. Wire the motor and feedback. See System Feedback for
additional information.
9. Wire Regen Resistor kit, if applicable.
10. Verify that all wiring is correct.
11. Verify that earth grounds are connected.
12. Verify all electrical and safety codes are met.
13. Connect the serial cable to connector C2 and PC. See the
appropriate Wiring Diagrams.
14. Install MOTIONLINK on the PC.
Startup processes can cause motor motion. Be certain that all
applicable safety precautions are taken to ensure that no harm
to personal or machine can occur.

Read Before Installing 06/04 Danaher Motion Kollmorgen
15. Using the Startup Wizard in MOTIONLINK:

A. Configure the SERVOSTAR CD for your particular motor,
if this was not done at the factory. Refer to the
MOTIONLINK Startup Wizard.
B. Enable the system.
2.1 Use As Directed

The restrictions for proper use of a SERVOSTAR CD system are:
− The amplifiers are components that are built into electrical
equipment or machines and can only be commissioned as
integral components of such equipment.
− The servo amplifiers are to be used only on earthed, three-
phase industrial main supply networks (TN-system, TT-system
with earthed neutral point).
− The servo amplifiers must not be operated on power supply
networks without an earth or with an asymmetrical earth.
− If the servo amplifiers are used in residential areas, or in
business or commercial premises, you must implement
additional filtering measures.
− The servo amplifiers are only intended to drive specific
brushless synchronous servomotors from Danaher Motion with
closed-loop control of torque, speed, and position. The rated
voltage of the motors must be at least as high as the DC-link
voltage of the servo amplifier.
− The servo amplifiers may only be operated in a closed switch
gear cabinet, taking into account the ambient conditions
defined in the environmental specifications.
Danaher Motion guarantees the conformance of the servo
amplifiers with the standards for industrial areas stated in the front
of this manual only if Danaher Motion delivers the components
(motors, cables, amplifiers etc).

Danaher Motion Kollmorgen 06/04 Unpacking and Inspecting
3 UNPACKING AND INSPECTING

Electronic components in this amplifier are design hardened to
reduce static sensitivity. However, proper procedures should be
used when handling.
Remove all packing material and equipment from the shipping
container. Be aware that some connector kits and other equipment
pieces may be very small and can be accidentally discarded if care
is not observed when unpacking the equipment. Do not dispose of
shipping materials until the packing list has been checked.
Upon receipt of the equipment, inspect components to ensure that
no damage has occurred in shipment. If damage is detected, notify
the carrier immediately. Check all shipping material for connector
kits, manuals, diskettes, and other small pieces of equipment.
3.1 New Description Label

Description:CE06550-000000
Reference Manual/wiring
Serial No: Z04E-2151 Diagram for Installation
and protection information
Model Number Firmware Version

Serial Number
3.2 Series 5 Part Number Guide
CD Series 5
Part Number Guide
Cx zz 5yw
Feedback Cont. Current Logic Power Control Interface

E: Encoder 03: 3 A 5: 300 V 0: Analog
B: Sine Encoder 06: 6 A 6: Ext. 24 V 1: SERCOS
R: Resolver 10: 10 A 4: DeviceNet
Examples:
CE 03 560 Encoder Feedback; 3 A; 24 V; Analog interface
CB 06 551 Sine encoder feedback; 6 A; 300 V; SERCOS interface
CR 06 564 Resolver feedback; 6 A; 24 V; DeviceNet (DNIB)

Unpacking and Inspecting 06/04 Danaher Motion Kollmorgen
3.3 Series 2 Model Numbers

Month Manufactured
A - January
B - February
:
:
L - December
Year Manufactured
Manufacturing Unit Manufactured

Location
S 9 8 A-5 8 9
CR03000-2G204
SERVOSTAR® Amplifier Family Motor Winding

S - S Series Motor Frame & Stack
C - CD Series (Compact Drive) Length
Feedback Motor Family

R - Resolver D - DDR Series
E - Encoder 0 - No Comp
B - Sine Encoder G - GOLDLINE (B, M, EB)
R - RBE (H)
H - SILVERLINE
L - Linear (Ironless)
Rated Current (Amps) C - Linear (Iron Core)
S Series: 03, 06, 10, 20, 30, 55, P - PLATINUM XT
85 S - GOLDLINE
CD Series: 03, 06, 10 (Submersible)
S Series Hardware Options
100 - 199 Custom DCB variations Voltage Level
200 Standard 0 - No Comp
201 SERCOS interface 1 - 115 VAC (160 VDC)
9xx Custom variations 2 - 230 VAC (325 VDC)
J - low-inductance motors
CD Series Hardware Options (with .SSV Variable file only)
250 Standard with 230 V logic input (see Y - Special Compensation
Note) * three-digit extension follows the Y
251 SERCOS interface with 230 V logic designator
input
260 Standard with 24 V logic input
261 SERCOS interface with 24 V logic
input
250 replaces previous standard option (200) originally

intended for single phase 3 and 6 amp units.

Danaher Motion Kollmorgen 06/04 Mounting
4 MOUNTING
For proper ventilation, vertically mount the SERVOSTAR CD and
mount them in an electrical enclosure to protect them from physical
and environmental damage.
4.1 Hardware Specifications

Amplifier Model Cx03 Cx06 Cx10
Unit Weight Lbs./kgs. 3.56/1.61 4.9/2.22 5.94/2.69
Mounting English (Metric) 10-32 (M4)
Hardware Applied Torque 20 lb-in. (2.26 N-m)
Line Screw Size/Torque
Connection bus Screw Size/Torque
M3.5/12 lb-in (1.35 N-m)
Hardware Motor Screw Size/Torque
Ground Screw Size/Torque
Control Logic (AWG/ mm2) 16 / 1.5
Motor Line (AWG/ mm2) 14 / 2.5
Main Input (AWG/ mm2) 14 / 2.5 12 / 4
22-18 AWG (0.3-0.75 mm2) Ferrules recommended:
18 AWG Type H0 - 75/14 Weidmuller 4629.0 or
Wire Size equivalent
Configurable I/O wire gauge
(AWG#) 20 AWG Type H0 - 5/14 Weidmuller 6907.0 or equivalent
22 AWG Type H0 – 34/12 Weidmuller 902577 or
equivalent
16/14 AWG (1.5 mm2): Hollingsworth XSS0954S OR
SS20947SF or equivalent
Spade Terminals
12/10 AWG (4-6 mm2): Hollingsworth XSS20836 OR
SS20832F or equivalent
Clearance Side-to-Side 0.5 in (12.7 mm)
Distance Top/Bottom 2.5 in (63.5 mm)
Includes: C1, C2, C4, C7
CK100 Kit
(plus 2 ft/0.69 m of stranded bus ribbon), C8
Danaher Motion #: A-93899-013
C3
Mating Vendor Info: Weidmuller BL3.5/13 Cat.No. 161574
Connector Danaher Motion #: A-81014-004
C5
Hardware Vendor Info: PCD ELFP04110
Connector Screw Torque 2.25 lb-in (0.25 N-m)
Danaher Motion #: A-81014-002
24 V Logic (optional)
Vendor Info: PCD ELFP02210 (or equiv.)
4.2 Control Specifications

Product Model Control Specifications
Update Rate 62.5 µs (16 kHz)
Current Loop Bandwidth <2400 Hz
Update Rate 62.5 µs (16 kHz)
Commutation Loop Max. Commutation Freq. 400 Hz
Output Waveform Sinusoidal
Update Rate 250 µs (4 kHz)
Bandwidth <400 Hz
Speed Command
Velocity Loop Serial: 1 rpm / Analog: (1/6554) * VMAX
Resolution
Long-term Speed
0.01% (µs clock tolerance)
Regulation
Position Loop Update Rate 500 µs (2 kHz)

Mounting 06/04 Danaher Motion Kollmorgen
Product Model Control Specifications

I/O Connector (C3 by pinout)
Absolute Maximum Voltage 13 V differential
Input Resolution 14 Bit/1.2
Sensitivity 1.53 mV min
-10 V to +10 V = -120% Motor rated
Analog Input (2, 3)
Voltage Range speed to +120% Motor rated speed
(Adjustable Vscale parameter)
Input Impedance/CMR > 10 kΩ/50 dB
Long-term Drift 100 ppm (0.075%/°C)
Fault Output Relay (5, 6) Max Capacity 1 A at 24 VDC
Bandwidth 2.5 kHz (Opto-isolated)
Remote Enable (7, 8)
Input Voltage Range 12 V to 24 V Nominal (bi-directional)
Configurable Inputs(7, 9,
10, 11) Min. On/Max. Off 10 V/1 V
Current Demand per Input 20 mA (max)
0 V to 48 V Nominal – bi-directional
Output Voltage (max.)
(Open Collector)
Configurable Digital
Output (7, 12) (Min. On) 1V
Max. Output Current 60 mA
Max. Output Current 1 mA (1 kΩ internal series resistance)
Configurable Analog Sensitivity / Resolution 4.9 mV/12 bit
Output (13, 4) Voltage Range -10 V to +10 V
Encoder Equivalent Output (C4 by pinout)
Output Voltage (high level)
2.5 V min. at 20 mA Differential
A/B/I & Complements (1, at 25° C
2, 4, 5, 7, 8) RS 485 Line Drive Type DS26C31TM
Remote Encoder Input (C8 by pinout)
Input Voltage at 25° C ±5 V Differential
A/B/I & Complements (1, Input Sensitivity ±0.2 V
2 ,4, 5, 7, 8) Input Impedance 100 Ω
RS 485 Line Receiver Type SN75173
See Position Loop for features using this input.
Note: A flyback diode is necessary for inductive loads connected across the 01 output.
4.3 Outline Dimensions

Cx10
99.1 [3.90]
Cx 06
83.3 [3.28]
Cx 03 Dimensions are in mm [inches]
67.3 [2.65]
36.6 163.0
6.7
[1.44]
[0.26] [6.42] 2.0
[0.08]
3 ∅ 5.5
[0.22]
15.5
[0.61]
2 ∅ 10.0
[0.39]
256.0
244.0 216.0 [10.08]
[9.61] [8.50]
HEAT
SINK
33.7
[1.33]

Danaher Motion Kollmorgen 06/04 Wiring
5 WIRING
The environment into which any electronic control system is
installed can effect its operation. Danaher Motion recommends the
SERVOSTAR system be operated and stored under the
environmental conditions stated in the product specification tables.
The system can operated in higher temperature ambient conditions
with a derating applied. Check with the factory for derating info.
Attention to proper installation and field wiring are of prime
importance to ensure long-term and trouble-free operation. Users
should familiarize themselves with and follow the installation and
wiring instructions listed in this section. In addition to these
practices, some localities and industries may require applicable
electrical and safety codes, laws, and standards.
Particular care should be used when designing the layout of an
enclosure. Efforts to separate power wires from small signal wires
should be taken. The following guidelines highlight some important
wiring practices:
− Control and signal cables must be separated from power and
motor cables. A distance of 20 cm (8 in.) is typically sufficient.
− Control and signal cables must be shielded to reduce the
effects of radiated interference.
− Where control cables must cross power or motor cables, they
should cross at a 90º angle, if possible. This reduces the field
coupling effect.
5.1 Enclosure
The Danaher Motion SERVOSTAR series of electronic system
components are designed for panel assembly. This panel assembly
should then be mounted in a metallic enclosure. Enclosures are
supplied by the manufacturers of the final product and must meet
the environmental IP rating of the end product. To ensure proper
grounding (and to optimize EMC), the enclosure should have
continuous ground continuity maintained between all metal panels.
This ground continuity is intended to be both a safety ground and a
high frequency ground. The units should be mounted on a back
plane, which is installed into the enclosure. Ideally, the back plane
should be an unpainted metallic surface to optimize electrical
bonding of the frame and provide the lowest possible impedance
path to earth ground. These enclosures also provide added safety.

Wiring 06/04 Danaher Motion Kollmorgen
5.2 Grounding
System grounding is essential for proper performance of the drive
system. A ground bus bar may be used as a single point ground for
the system. Safety grounding should be provided to all pieces of
the system from a star point. In addition to the safety grounding, a
high frequency ground must be provided that connects the back
panel to the enclosure and to earth ground. The objective is to
provide an extremely low impedance path between the filters,
drives, power supplies, and earth ground. This high frequency
ground is accomplished with the use of a flat braid or copper bus
bar. It is important not to rely on a standard wire for the high
frequency ground. In general, wire has an inductance of 8nH-per-
inch, regardless of diameter. At higher frequencies, this unwanted
inductance between grounds equates to limited filter performance.
When connecting high frequency grounds, use the shortest braid
possible.
5.3 Bonding
The proper bonding of shielded cables is imperative for minimizing
noise emissions and increasing immunity levels of the drive system.
Its effect is to reduce the impedance between the cable shield and
the back panel. Danaher Motion recommends that all shielded
cables be bonded to the back panel.
Power input wiring does not require shielding (screening) if the
power is fed to the cabinet (enclosure) via metallized conduit. If the
metallized conduit is used with proper high frequency grounds,
bonding technology, and recommended wire routing, then power
input wire shielding has no affect. In the event that metallized
conduit is not implemented into the system, shielded cable is
required on the power input wires and proper bonding technologies
should be implemented.
The motor and feedback cables should have the shield exposed as
close to the drive as possible. This exposed shield is bonded to the
back panel using one of the two following methods.

5.3.1 NON-INSULATED CABLE CLAMP

Terminal Clamp and Cx Drive Clamp show how cable bonding is
implemented using non-insulated metallic cable clamps.
Cx
From the drive
Terminal Strip
Bonded to Back
Plane
To Motor
Terminal Clamp Cx Drive Clamp
5.3.2 ALTERNATIVE BONDING METHODS

Another option is to use cable bonding clamps offered by Phoenix
Contact (and others). When using the Phoenix Contact parts, make
sure that a low impedance (high frequency) ground is connected
from the ground bus bar to the back panel. This can be done with a
flat braid or a copper bus bar. The SK parts from Phoenix (SK8,
SK14, & SK20) slide onto the bus bar. The cable (with exposed
shield) is inserted through the SK piece and the thumbscrew on top
of the SK piece is used to tighten the connection between the cable
shield and the bus bar.
Phoenix Contact Part # Description Cable Diameter Range
3025163 Shielded terminal block – for SK8
Type SK8 placing the shield on bus bars. up to 8 mm or 0.315 in
3025176 Shielded terminal block – for SK14
TypeSK14 placing the shield on bus bars. 8 mm to 14 mm or 0.551 in
SK20
3025189 Shielded terminal block – for
14 mm to 20 mm or
Type SK20 placing the shield on bus bars.
0.787 in
0404428 Support for bus bar. 2 needed N/A
Type AB/SS to mount ground bus.
0402174 Bus bar material – 10 mm x 3
N/A
Type NLS-CU 3/10 mm copper at varying lengths.
Phoenix Contact - Side View and Phoenix Contact -Top View

represent a side and top view of the SK device that clamps down
on the shield of the cable. The Phoenix SK device is excellent for
providing a low impedance path between cable shield and the back
panel.

Thumb screw to tighten down shield
to bus bar
Cable shield compressed
on copper bus bar
Copper bus bar
K(8, 14, 20, - Shielded terminal block
Phoenix Contact - Side View

SKx – for
connecting
shield to bus
Support for bus bar bar
Copper Bus Bar
High frequency ground

connection to back panel
from bus bar
Phoenix Contact -Top View
5.4 CE Filtering Techniques

The SERVOSTAR drive system meets the CE Mark standards
stated in the front of this manual. It is imperative for you to apply
proper bonding and grounding techniques, described earlier in this
section, when incorporating EMC noise filtering components for the
purpose of meeting this standard.
Noise currents often occur in two types. The first is conducted
emissions that are passed through ground loops. The quality of the
system grounding scheme inversely determines the noise
amplitudes in the lines. These conducted emissions are of a
common-mode nature from line to neutral (or ground). The second
is radiated high-frequency emissions usually capacitively coupled
from line-to-line and are differential in nature.
To properly mount the filters, the enclosure should have an
unpainted metallic surface. This allows for more surface area to be
in contact with the filter housing and provides a lower impedance
path between this housing and the back plane. The back panel, in
turn, has a high frequency ground strap connection to the enclosure
frame or earth ground.

5.4.1 INPUT POWER FILTERING

The Danaher Motion SERVOSTAR CD electronic system
components require EMI filtering in the input power leads to meet
the conducted emission requirements for the industrial
environment. This filtering blocks conducted-type emissions from
exiting onto the power lines and provides a barrier for EMI on the
power lines.
Care must be taken to adequately size the system. The type of filter
is based on the voltage and current rating of the system and
whether the incoming line is single or three-phase. One input line
filter is used for multi-axis control applications. These filters are
mounted as close to the incoming power as possible so noise is not
capacitively coupled into other signal leads and cables. Several
manufacturers of these filters are listed below. They should be able
to recommend the best filter design for most typical motor control
applications. Danaher Motion has also provided specific filters
recommendations that adequately attenuate the conducted noise to
levels well below the CE limits. The recommendations are:
− Filter should be mounted on the same panel as the drive.
− Filter should be mounted as close as possible to incoming
cabinet power.
− When mounting the filter to the panel, remove any paint or
material covering. Use an unpainted metallic back panel if
possible.
− Filters are provided with an earth connection. All ground
connections are tied to ground.
− Filters can produce high leakage currents. Filters must be
earthed before connecting the supply!
− Filters should not be touched for a period of 10 seconds after
removing the supply.
- Filter type must be chosen that has capacitors on its outputs
line-to-line and line-to-earth. Filters that have inductors as the
last output stage without these final capacitors are not
compatible.
Recommended Line Filters
BUS Module Model # Recommended EMI Line Filter Danaher Motion Part #
Cx03 Filter Concepts SF7 n/a
Filter Concepts 3H Series* A-96776-001
Schaffner FN258-7/07
Cx06 Filter Concepts SF15 n/a
Filter Concepts 3H Series* A-96776-002
Schaffner FN258-16/07
Cx10 Schaffner FN258-16/07 A-96776-002
Filter Concepts 3H Series*
*Filter Concepts 3F Series is only compatible if H-option is selected (i.e.:
3F30DAH). Other models are know to cause over-voltage faults.
The filters called out in the table above are used on a one-to-one
correspondence with the drive. If drives are paralleled off one filter, it
needs to be sized. Drives can be ganged off one EMI filter as shown in
the Filter and Bonding Diagram.
NOTE

5.4.2 MOTOR LINE FILTERING

Motor filtering may not be necessary for CE compliance of
SERVOSTAR systems. However, this additional filtering increases
the reliability of the system. Poor non-metallic enclosure surfaces
and lengthy, unbonded (or unshielded) motor cables that couple
noise line-to-line (differential) are just some of the factors that lead
to the necessity of motor lead filtering.
Motor lead noise may be either common-mode or differential. The
common-mode conducted currents occur between each motor lead
and ground (line-to-neutral). Differential radiated currents exist from
one motor lead to another (line-to-line). The filtering of the lines
feeding the motor provide additional attenuation of noise currents
that enter surrounding cables and equipment I/O ports in close
proximity.
Differential mode currents commonly occur with lengthy motor
cables. As the cable length increases, so does its capacitance and
its ability to couple noise from line-to-line. While every final system
is different and every application of the product causes a slightly
different emission profile, it may become necessary to use
differential mode chokes to provide additional noise attenuation to
minimize the radiated emissions. The use of a ferrite core (placed
at the drive end) on each motor lead (shown in the diagram below),
attenuates differential mode noise and lower frequency (30-60
MHz) broadband emissions to within specifications. Danaher
Motion recommends a Fair-Rite P/N 2643665702 (or equivalent)
ferrite core. You should wrap each motor lead through the core
several times.
Never wrap a ground lead through a core.

WARNING
Differential Mode Filtering
Common Mode
Filtering
To motor
To Motor
From Drive
V
From Drive Output
Common mode currents commonly occur from noise spikes created

by the PWM switching frequency of the drive. The use of a ferrite or
iron-powder core toroid places common mode impedance in the
line between the motor and the drive. The use of a common mode
choke on the motor leads increases signal integrity of encoder
outputs and associated I/O signals.

The following is a list of toroidal and ferrite cores used to make
common mode chokes:
Manufacturer Manuf. Part # Size
OD 4 in (102 mm), ID 2.25 in. (57.2 mm.)
Micrometals T400-26D
HT 1.3 in (33 mm.)
OD 1.025 in(26 mm) ID 0.6 in. (15.2 mm.)
Micrometals ST102-267
HT .475 in (12.1 mm.)
OD 1.52 in (38.6 mm) ID 0.835 in. (21.2 mm.)
Micrometals ST150-275B
HT .825 in (21 mm.)
OD 2.01 in (51.1 mm) ID 1.24 in. (31.5 mm.)
Micrometals ST200-275B
HT 1.025 in (26 mm.)
OD 1.09 in (27.7 mm) ID .555 in. (14.1 mm.)
Magnetics 77930-A7
HT .472 in (11.99 mm.)
OD 2.4 in (61 mm) ID 1.4 in. (35.55 mm.)
Fair-Rite 2643803802
HT 0.5 in (12.7 mm.)
Manufacturer’s Danaher Motion

Manufacturer Description
Part # Part #
500 µH 3 phase common mode
Schaffner RD7137-36-0m5 A-96843-005
choke. 36 amps continuous.
500 µH 3 phase common mode
Schaffner RD8137-64-0m5 A-96843-010
choke. 64 amps continuous.
5.4.3 I/O FILTERING

I/O filtering may be desirable (depending on system installation,
application, and integration with other equipment). To avoid
unwanted signals entering and disturbing the drive system or other
associated equipment, place ferrite cores on I/O lines. The
following chart lists some recommended ferrite parts used for I/O
filtering and noise attenuation. These parts are ideal for providing
an in-line common mode impedance for I/O lines (Fair-Rite
Products Corporation also has a varied selection for most
applications).
Manufacturer’s Danaher Motion
Manufacturer Description
Part # Part #
Ferrishield SS33B2032 A-96770-003 Clamp on core
Ferrishield SS33B2036 A-96769-005 Clamp on core
Ferrishield FA28B2480 A-96771-003 Clamp on core - flat cable clamp
Ferrishield SA28B4340 A-96772-009 Clamp on core - flat cable clamp
* Fair-Rite 2643167251
* This core must be used with the CD-Series of drives

for CE compliance. It should be applied to the 24 V
input power lines and the Remote Enable lines (7 & 8
on C3 connector) with approximately three turns
CAUTION through the core.
Clamp-on cores (below) use multiple turns through a clamp-on

core. The more turns created, the more impedance is added to the
line. Avoid putting the shield in a clamp-on core. It is undesirable to
place an impedance in-line with the shield. The use of ribbon cable
may be common in many cabinets. Some ferrite clamps are
designed just for ribbon cable use.
Flat cable clamp used with ribbon cable

5.4.4 FILTER AND BONDING DIAGRAM

Contactor, Cabinet/Enclosure
Fuses,
Xfmr,
etc.
1 Back Plane
230
VAC
XFMR
CNC / PLC / Controller

4 Controller I/O
EMI
filter
EMI 8
filter
CD CD
2 5
3
9
Routed Routed
to to
Motors Motors
Note 1 - Input power enters enclosure from metal conduit. This eliminates
the need for shielded input power cable.
Note 2 - Single point ground. A bus bar (ground bus) is an excellent way to
achieve this.
Note 3 - High frequency ground between non-conductive back panel and
enclosure. Also, a high frequency ground is required between the
enclosure and earth ground.
Note 4 - EMI filter grounding. Safety grounds must be provided on the
filters. Hazard potentials exist even when the power is off
because of the capacitors internal to the filters.
Note 5 - Bonding of motor cables. The use of armored (screened) motor
cables bonded as close to the drive as possible are essential for
CE compliance and strongly recommended to better the overall
performance and reliability of the system.

Note 6 - Feedback cable bonding is required for CE compliance. As with the
motor cables, the feedback cables should be bonded to the back
panel. This bonding does two things. First, it cuts down radiation
from the drive, which may be in the form of high frequency energy
resulting from internal processor clocks. Second, it provides
immunity for the drive. Since the feedback device is located
internal to the motor, it is going to pick up some noise currents
and transmit them along the feedback cable. The bonding directs
the currents from the shield of the feedback cable to back panel
ground. This reduces the amount of noise entering the drive.
Note 7 - AC power lines that must be routed past other lines (such as motor
cables or I/O lines) should cross at a 90º angle. This minimizes
the coupling effect. Additionally, the power lines should be routed
as close to the back panel as possible. Any noise currents on the
lines are capacitively coupled to the ground plane and not to other
lines.
Note 8 - Control (I/O) signals should be kept separate from all power and
motor cables, if possible. Keep control wiring as short as possible
and use screened wire. Bonding is also recommended but not
required for CE compliance. A separation distance of 20 cm (8 in)
is sufficient in most cases. Where control cables must cross
power cables, they should cross at a 90º angle.
Note 9 - Motor cables and feedback cables exiting the cabinet going to the
motor should be separated as much as possible. Ideally, the use
of separate conduits provides good isolation, which can limit
coupling of noise from motor to feedback cables.
5.5 System Interconnect

The following sections provide connector information and the
system connections up to the motor power and feedback
connections. Cabling purchased from Danaher Motion directly
completes the system connections. Customers making their own
cables can refer to Appendix A for drive/motor pinout connections.

5.5.1 ELECTRICAL SPECIFICATIONS

Product Model Cx03* Cx06* Cx10
Voltage ( VACL-L) Nominal ±10% 110 to 230 230

115 VAC 1φ or 3φ 3φ only
230 VAC 1φ or 3φ 3φ only
Line Frequency 47-63
0.44 (1φ) 0.89 (1φ) 2.4
kVA at 115 VAC
0.6 (3φ) 1.1 (3φ) (3φ only)
0.88 (1φ) 1.8 (1φ) 4.6
Main Input kVA at 230 VAC
1.4 (3φ) 2.8 (3φ) (3φ only)
Power
6.2 (1φ) 10 (1φ) 13
Continuous Current (amps)
4 (3φ) 7.8 (3φ) (3φ only)
Peak Current (amps) 18.6 (1φ) 30 (1φ) 26
for 500 ms 12 (3φ) 23.4 (3φ) (3φ only)
12.4 (1φ) 20 (1φ) 26
Peak Current (amps) for 2 sec
8 (3φ) 15.6 (3φ) (3φ only)
Line Fuses
10 15 15
(FRN-R, LPN, or equiv.)
+24 VDC Ext. Logic Voltage (volts) 22 to 27
Logic Input
Power +24 VDC Ext. Logic Current
1.5
Cxxx26x (amps sink)
Models ONLY +24 VCD Ext. Logic Current
2.6
(amps max surge)
Max. Surge Current (amps) 30
SoftStart
Max. Charge Time (sec) 0.25
Fault Contact Rating (amps) 1
Protection
Fault Contact Closing Period (ms) Close = 3 ms, Open = 2 ms
Functions
OverTemperature trip 80°C (176°F)
Cont. Power (KVA) at 115 VAC 0.35 (1φ) 0.7 (1φ)
1.8 (3φ)
Line Input (45°C (113°F) Ambient) 0.55 (3φ) 1.1 (3φ)
Cont. Power (KVA) at 230 VAC 0.7 (1φ) 1.4 (1φ)
3.5 (3φ)
Rated Main Line Input (45°C (113°F) Ambient) 1.1 (3φ) 2.2 (3φ)
Output Cont. Current (Arms) 3 6 10
(Ma, Mb, Mc) Peak Current (Arms) for 500 mSec 9 18 20
Peak Current (Arms) for 2 Sec 6 12 20
PWM Frequency (kHz) 16 8 8
PWM Motor Current Ripple (kHz) 32 16 16
Form Factor (rms/avg) ≤1.01
UnderVoltage Trip (nominal) 90 VDC
Protective OverVoltage Trip 430 VDC
Functions OverTemperature Trip 80°C (176°F)
Internal heat dissipation (watts) 60 80 132
Operation temperature 5°C (41°F)to 45°C (113°F)
Storage temperature 0°C (32°F) to 70°C (158°F)
Ambient humidity 10% to 90%
Environment Atmosphere without corrosive gasses or dust
Derate 5% per 1000 ft. (300m) above 3300
Altitude
ft. (1000m)
Vibration 0.5 g
*NOTE: Model Numbers Cx0x200 are single phase only!

5.5.2 REGEN INFORMATION

Product Model Cx03 Cx06 Cx10
Peak current (amps) 20
External Shunt
Regulator Minimum resistance (ohms) 20
Watts 200
Capacitance (Farads) 0.00082 0.00164
bus Voltage (nominal) ( VDC) 325
Application Information VHYS (Regen circuit turn-off) (
370
VDC)
VMAX (Regen circuit turn-on) (
390
VDC)
External Regen Kits ERH-26 a a a
*For guidance on application sizing of Regen Kits, see the SERVOSTAR CD-Series
Regeneration Requirements Application Note.
5.5.3 MATING CONNECTORS

Description Mating connector Part Number
C1 RS232 D9 Female EDA 8S0009SS402S25 Connector 9
pins D type for Cable solder
C2 Encoder Feedback D25 Male EDA 8S0025SS402525 Connector 25
pins D Type For Cable solder
C3 User I/O Weidmuller STX Part Number CON-00000013-01
Weidmuller 800161574
C4 Encoder Equivalent output D9 Female or EDA 8S0009SS402S25 Connector 9
or Sercos pins D type for Cable solder
SERCOS
C7 Multidrop connector (Daisy 10 Pin (0.1”x0.1”)
chain) Female ribbon
C8 Remote encoder input D9 female EDA 8S0009SS402S25 Connector 9
pins D type for Cable solder
C9 Extended I/O 20-Pin Connector STX Part Number CON-00000020-15
for flat cable
Hirose FX2BA-20SA-1.27R
Ma To motor phases Spade Terminals
Mb
Mc
B+ Regen Spade Terminals
C
L1 Power supply input Spade Terminals
L2
L3
GND Two GND terminal Ring Terminals
24 VDC Optional Logic supply PCD STX Part Number CON-00000002-05
PCD ELFP02210
All mating connectors are supplied with the drive.

5.5.4 KIT PARTS AND MODELS

Kit Parts / Kit Models ER-20 ER-21 ER-22 ER-23
2.2 (two in 2.2 (two in
Resistance (ohms) 4.5 4.4
parallel) parallel)
Resistor Power Rating (watts) 500 1000 1000 2000
A-79916- A-93317- A-79916- A-93317-
Danaher Motion Part No.
007 027 007 027
Relay Trip Setting (A) 10.5 15 21 30
Overload
A-93142- A-93142- A-93142- A-93142-
Relay Danaher Motion Part #
007 008 010 010
(Fast Trip)
Auto/Manual Setting Manual Manual Manual Manual
Hookup Wire Gauge/Temp Rating #8 AWG/125°C
ER-30 ERH-26 ERH-40

Resistance (ohms) 8.8 20 8.8
Resistor Power Rating (watts) 400 200 100
Danaher Motion Part # A-84776-001 P-97742-001
Overload Relay Trip Setting (A) 7 N/A N/A
Relay Danaher Motion Part # A-93142-006 N/A N/A
(Fast Trip)
Auto/Manual Setting Manual N/A N/A
Hookup Wire Gauge/Temp Rating #8 AWG/125°C
5.6 Wiring Diagrams

5.6.1 TOP VIEW
C7
C8
C9
10
24 VDC Input

5.6.2 CONNECTOR PIN-OUT FOR C-9
Extended
I/O Mating connector:
A B P/N HIROSE FX2BA-20SA-1.27R
1
10 Pin Ribbon Cable IDC connector
10
Pin # Function Description Comments

A3 IN5 Bipolar
B3 IN4 Bipolar
B4 IN6 Bipolar
B5 Common For IN4 to IN6 Common For IN4 to IN7 Source or Sink
5.6.3 MAKING CONNECTIONS TO C-9

Connector C9 mate is included with the drive. It is an Insulation
Displacement Connector (IDC) able to accept a 10-conductor
ribbon cable. The cable is inserted in the end of the connector and
held in place while the connector is clamped together ether with the
use of a clamping tool or a vice. The other end of the ribbon cable
may be terminated in any manor desirable.
5.6.4 WIRING DIAGRAM NOTES

Note 1: FUSE 2 and contactor are not required if the input power line is
neutral. (Also see Note 9)
Note 2: Allow 30 seconds after turning power off before reapplying
power.
Note 5: All AC line wires should be a twisted pair.
Note 6: The ground of the drive and motor best minimizes ground
currents and noise when connected in a star point configuration.
Note 10: Cables should be properly bonded to the back panel and
implemented as close to the drive side of the cable as possible
for effective grounding. If bonding is installed, the shield on the
cable end need not be connected to the star point configuration.
Only connect the shild on one end of the cable (preferably on the
drive side).
Note 11: Units must be installed in an enclosure that meets the
environmental IP rating of the end product (ventilation or cooling
may be necessary to prevent enclosure ambient from exceeding
45° C or 113° F).
Note 12: Do not connect unused pins on C1 connector. Connecting all the
pins on some manufacturers' cables produce unpredictable
results.
Note 13: See the SERVOSTAR Cx Hardware Specifications for wire
gauge and ferule sizes.
Note 14: See CE Filtering Techniques for further information.
Note 16: See the SERVOSTAR Cx Hardware Specifications for spade
terminal sizes.
Note 17: This system is suitable for use on a circuit capable of delivering
not more than 5000 RMS symmetrical amps, 240 V maximum.
Note 18: A flyback diode is necessary for inductive loads connected
across the 01 output.

5.6.5 FRONT VIEW

Cx Drive
STATUS DISPLAY
C1
6 1
7 2
8 3
HEAT SINK
(Cx06 & Cx10)
9 4
5
C2
25 13
24 12
23 11
22 10
21 9
20 8
19 7
18 6
17 5
16 4
15 3
14 2
1
MA
C3
1
MB 2
3
MC 4
5
B+ 6
7
C 8
9
L1 10
11
L2 12
13
L3
C4 5
9
3
6
1
5.6.6 C1 COMMUNICATIONS PORT

COMMUNICATIONS (D9S)
C1 RS-485 SERIAL LINK
Tx +
6
Tx - DATA FROM SERVOSTAR
7
Rx +
8
Rx -
9 DATA TO SERVOSTAR
COMMON 5
RS-232 SERIAL LINK

C1
1 1
6
(RXD) 2 2
DIAGRAM REPRESENTS
7
(TXQ) 3 3
8
4 4
TYPICAL CONNECTION
9
COMMON 5 5
Do NOT connect unused pins on C1 connector.

Connecting all the pins on some manufacturers' cables
produce unpredictable results.
NOTE


C2
13 FEEDBACK (D25)
25
12
24
11
23
10
22
9 TO MOTOR
21
8 FEEDBACK
20
7 DEVICE
19
6
18
5
17
4
16
3
15
2
14
1
Cables should be properly bonded to the back panel

and implemented as close to the drive side of the cable
as possible for effective grounding. If bonding is
installed, the shield on the cable end need not be
connected to the "star point" configuration. Only
connect the shild on one end of the cable (preferably on
NOTE
the drive side). See the Hardware Specifications for wire
gauge and ferule sizes.

C3 CONFIGUREABLE I/O INTERFACE (SEE NOTE 13)
1
2 HIGH
3 ANALOG INPUT ± 10V
LOW
4 DC REFERENCE FOR ANOUT**
5 SUPPLY FAULT OUTPUT RELAY
6 C SUPPLY (DRY CONTACTS)
7 +24V
8 REMOTE ENABLE
9 CONFIG.INPUT (IN1) USER SUPPLIED
CONFIG. INPUT (IN2) 24V POWER SUPPLY*
10
CONFIG. INPUT (IN3) RTN
11 *SEE SERVOSTAR
CONFIG. OUTPUT (O1)
12 C1 ELECTRICAL
CONFIG. OUTPUT ( ANOUT) SPECIFICATIONS FOR
13
METER LOADING INFORMATION
A flyback diode is necessary for inductive loads

connected across the 01 output.
NOTE

C4 ENCODER EQUIVALENT OUTPUT (D9P)
5 B
9
B
I
3 I
A
6
A
1
DRIVE DC COMMON (SEE TEXT IN MANUAL)
TX TRANSMIT
REPLACES C4 ON SERCOS MODELS

RX RECEIVE
Internal DC common for referencing ANOUT. It is also

provided to tie electrical equipment commons together
inside the drive to prevent excess common mode
WARNING voltages from destroying I/O (internal fusing).

22
Wiring
~5 V
COMMON
See the SERVOSTAR Cx
6
Hardware Specifications
E-STOP and Bus Module Hardware
C8
Specifications for spade
EXTERNAL RESISTIVE (SEE NOTE 10) terminal sizes.
REGEN UNIT (ERH-26) (SEE NOTE 13)
MA
1
5
3
MB
RESISTOR (SEE NOTE 5)

MC
B+
THERMOSTAT
C
(SEE NOTE 14)
MAIN INPUT SHIELD TO (SEE NOTE 13)
L1
POWER STAR POINT
FUSE 1 L2
LI FRET
L1 L3
FUSE 2
L2
T UP NI
FUSE 3
STAR
06/04
(SEE NOTE 1) POINT
MOMENTARY Single Phase Users (SEE NOTE 6)

PUSHBUTTON Connect any two lines
TO ENERGIZE L3
M-SS-017-01 Rev. T
MAIN POWER.
CUSTOMER SUPPLIED
MOTOR POWER (SEE NOTE 13)
MAIN POWER
NORMALLY OPEN AUXILLARY POWER CONTACTOR FROM MAIN POWER CONTACTOR
5.6.11 C8 REMOTE ENCODER INPUT

CONTACTOR (SEE NOTE 10)
Note 1 FUSE 2 and contactor are not required if the input power line is neutral.
Note 5: All AC line wires should be a twisted pair.
Note 6: The ground of the drive and motor best minimizes ground currents and noise when connected in a "star point" configuration.
Note 10: Cables should be properly bonded to the back panel and implemented as close to the drive side of the cable as possible for effective grounding. If
5.6.10 MAIN INPUT POWER CONNECTIONS
bonding is installed, the shield on the cable end need not be connected to the "star point" configuration. Only connect the shild on one end of the
cable (preferably on the drive side).
Note 13: See the SERVOSTAR Cx Hardware Specifications and Bus Module Hardware Specifications for wire gauge and ferule sizes.
Note 14: See CE Filtering Techniques for further information.
I
I
A
A
B
B
Danaher Motion Kollmorgen
SERVOSTAR CD Installation
5.7 Pinout Connectors

C1: Communications Connector C2: Feedback Connector
Pin Function Pin Resolver Encoder Sine Encoder
1 Shield 1 Sine High A A

2 REC (RXD) (RS232) 2 Sine Low /A /A
3 XMIT (TXD) (RS232) 3 Shield Shield Shield
4 Reserved DO NOT CONNECT 4 Cosine High B B
5 Common 5 Cosine Low /B /B
6 TxD+ (RS485) 6 Shield Shield Shield
7 TxD- (RS485) 7 E5V Return E5V Return
8 RxD+ (RS485) 8 E5V Return E5V Return
9 RxD- (RS485) 9 H1B H1B(/C)
(/Data)
C3: User I/O Connector 10 H2B H2B(/D)
Pin Function (/Clock)
11 H3B H3B
1 Analog Signal Shield
12 Shield Shield Shield
2 Analog Differential Input + (High)
13 Thermostat Thermostat Thermostat
3 Analog Differential Input - (Low) High High High
4 DC Reference for ANOUT* 14 Shield Shield Shield
5 Fault Output Relay Contact 15 Ref. High Out Index Index
6 Fault Output Relay Contact 16 Ref. Low Out /Index /Index
7 +24V Input (Common Rail for 17 Shield Shield Shield
return pins 8,9,10,11)
18 E5V Supply E5V Supply
8 Remote Enable Input
9 Configurable Input(See IN)
10 Configurable Input (See IN2)
21 Shield Shield Shield
11 Configurable Input (See IN3)
22 H1A H1A (C) (Data)
12 Configurable Output (See O1)
23 H2A H2A (D)
13 *Configurable Output (See (Clock)
ANOUT)
24 H3A H3A
* Internal DC common for Referencing
ANOUT. It is also used to tie electrical 25 Thermostat Thermostat Thermostat
equipment commons together (inside the Low Low Low
drive) to prevent excess common mode
voltage from destroying I/O (internally-
fused). SERCOS Ports
(Replaces C4)
C4: Encoder Equivalent Output
Pin Function
Tx
1 Channel A Output + (High)
2 Channel A Output - (Low)
Rx
3 DC Common
4 Channel B Output + (High)
5 Channel B Output - (Low)
6 Shield
7 Index Output + (High)
8 Index Output - (Low)
9 Shield

Notes for DIP switch:
DIP (Configuration) Switch The 10-position DIP switch is provided for drive
Switch Function Settings configuration. The first six switches control
communications parameters and are read only at
1 Bit 0 of MultiDrop Address
(LSB) power up. Any changes in these settings requires
2 Bit 1 of MultiDrop Address cycling the power. The other two switch
3 MultiDrop Bit 2 of MultiDrop Address functions (7, 8) control the motor operation and
4 Addressing Bit 3 of MultiDrop Address
are monitored in realtime. This switch provides
5 Bit 4 of MultiDrop Address
the following functions:
(MSB) Switches 1 through 5 set the
6 Serial/SERCOS 0 = 9600 (2M) drive's address. A drive having
Baud Rate 1 = 19200 (4M) address 0 powers up in the
MultiDrop
7 HOLD Mode 0 = Hold Mode Inactive addressed state. If these five
Address
Switch 1 = Hold Mode Active switches are set to anything but
Select
0, the drive will assume an
8 Drive Enable / 0 = Drive Enable
Disable
address code indicated by the
1 = Drive Disable switch settings.
9 SERCOS Transmit 0 = Low Power Switch 6 sets the
Power 1 = High Power serial/SERCOS baud rate to
Baud Rate
10 Factory Reserved Must Be set to 0 either 9600/2 M (switch off) or
19200/4 M (switch on).
Activating switch 7 causes the
drive to enter a position hold
Setting the switch to “1” mode. The condition is
means “Closed” or “On”. enunciated to the user by a
Position flashing status display. The
NOTE
Hold display maintains its current
OPMODE code. If the drive is
24V
running during a HOLD

detection, the motor ramps to a
stop at the DECSTOP rate.
C8
C7
OFF
Switch 8 is an input to the drive
enable circuitry and can be used
10
Enable
to force the drive to a disabled
state.
Functions only on SERCOS
C7: MultiDrop Communications
interfaceTM products. If switch 9
Type: 10 Pin (0.1”x 0.1”) Female is set to 0, the SERCOS
Ribbon Cable. Connector and cable SERCOS transmitter uses a low power
are included in the optional CK100 Power Level setting so the receiver is not
kit. overdriven when using short
This connector functions only when cables. Long cables require
using the RS232 interface. It will more power.
NOT function using RS485. Factory
Must be set to 0.
Reserved
C8: Remote Encoder Input

Pin Function C9: External User I/O*
1 A Input + (High) Pin Function
2 A Input - (Low) A3 Configurable input (see IN5)
3 DC Common B3 Configurable input (see IN4)
4 B Input + (High) B4 Configurable input (see IN6)
5 B Input - (Low) B5 Common for IN4, IN5, and IN6
6 Shield Connection A8 Output O3
7 Reserved B8 Output O2
8 Index + B9 Common for O2 and O3
9 Index - *Valid for Series 5 ONLY

5.8 System Feedback

The SERVOSTAR can receive resolver, encoder (with or without
halls), or sine encoder feedback. Danaher Motion offers a variety of
motors with options for these various feedback devices. The device
preference and the associated model number must be determined
when the order is placed.
5.8.1 RESOLVER
The SERVOSTAR uses either single (two poles) or multi-speed
(multiple poles) resolver feedback to monitor the motor shaft
position. A resolver can be thought of as a transformer whose
output is unique for any given shaft position (an absolute position
feedback). The transformer is driven with a sinewave reference
signal. Two AC signals are returned from the resolver into the Sine
and Cosine inputs. All three of these sinewave signals are low-level
and susceptible to noise.
5.8.2 RESOLVER FEEDBACK DIAGRAM

MOTOR OVERLOAD PROTECTION
MUST BE USED. THERMOSTAT SWITCH MAY SEE

PROTECTION OR EXTERNAL MOTOR OVERLOAD
0.45 X RATIO
MOTORS MUST HAVE INTEGRAL THERMAL
RESOLVER
+12 VOLTS AND 20 ma.
(SEE BELOW)
SINE LO
COS LO
SINE HI
REF LO
COS HI
REF HI
RESOLVER VERSION
13
12
11
10
9
8
7
6
5
4
3
2
1
C2
25
24
23
22
21
20
19
18
17
16
15
1
4

5.8.2.1 SPECIFICATIONS
Resolver Requirements
Type Control Transmitter
Transformation Ratio 0.47
Modulation Frequency 7-8 kHz
Input Voltage (From Drive) 4.25 VAC
Max DC Resistance 120 Ω (stator)
Max Drive Current 55 mA ACRMS
Output Voltage (To Drive) 2 VAC
5.8.2.2 CABLE LENGTHS

It is important to use properly- shielded cable and to keep it away
from other noise-radiating devices and cables. It is not
recommended to run the feedback and motor cables in the same
conduit. Danaher Motion has tested cable lengths up to 75 ft (22.9
m). without degradation of performance. However, performance
may vary, depending on motor and resolver type. Tests were
performed with standard Danaher Motion cable and its low-
impedance and Danaher Motion GOLDLINE motor resolver. Please
consult the factory for cable and resolver impedance specifications
when long cable runs above 250 ft (76 m) are desired. Danaher
Motion recommends twisted-shielded pair for feedback cables.
5.8.2.3 RESOLUTION AND ACCURACY

The SERVOSTAR calculates motor velocity as the derivative of
position (change in position over time). With its patented technique,
all readings are extended to a resolution of 16-bit. For velocity
feedback calculations, the drive converts the resolver input to 18-
bits of resolution, giving smooth motor velocity control. The digital
resolution (RDRES) of the Resolver-to-Digital Converter system is
determined automatically according to the application velocity limit
(VLIM). The following is a summary of the SERVOSTAR’s
resolution capabilities:
R/D Converter Specifications
VLIM (rpm) RDRES Counts/Rev Encoder Eqv. Output (C4)
> 6100 12 4096 4096 quad counts
1500 to 6100 14 16384 16384 quad counts
< 1500 16 65536 65536 quad counts
System accuracy using resolver feedback is effected by several

components. The following table gives information on the
inaccuracy that each of these components contribute to the total
accuracy of a standard SERVOSTAR system:
Resolver Accuracy Specifications
Components Arc-minutes
R/D Converter 4
Resolver mechanics (rotational) 8
Resolver mounting on motor shaft 2
Inter-LSB (digital dither over the least significant bit) 5
Total (Worse-case) 19

5.8.3 DIGITAL ENCODER

The SERVOSTAR can use encoder feedback to monitor the motor
shaft position. As opposed to a resolver, which is an absolute
position feedback device, the encoder is an incremental device that
indicates changes in position. The encoder resolution of the
SERVOSTAR (and therefore the drive’s encoder equivalent output)
is fixed because it is a hardware characteristic of the encoder
device. The encoder interface includes three groups of wires:
1. A/B (and complements) lines make up the encoder quadrature
signals. The signals are received differentially through line
receivers before being passed through a wire-break detection
circuit.
2. The narrow Index pulse normally appears once per revolution
and indicates a known physical position of the shaft. This pulse
is received differentially through a line receiver before being
passed through a wire-break detection circuit. This signal is
hardware-capturable.
3. Hall signals provide information representing the approximate
absolute location of the motor shaft. From this information, the
motor can sinusoidally commutate forward until the index
signal is detected - at which time, true position is known. These
signals are isolated by an opto-coupler and can be differential
or open-collector type signals.
Encoder Requirements
Types: A, B with or without Index pulse
Required Signals A, B, Index with or without Hall Channels
* Halls may be integral or discrete
Signal Type: A-quad-B and Marker Differential: do not connect single-ended
Halls Differential or Open Collector
System Voltage 5 VDC
Maximum Input Frequency From encoder: 3 MHz (before quad), 12 MHz (after quad)
Maximum Cable Length System Dependent: 50 ft. (15 m) Recommended
Maximum Line Count Per Motor Electrical
10,000,000
Cycle
Maximum Supply Current from drive 250 mA
Separate Voltage Regulator, Broken wire detector for A, B,
Protection
Index, and Hall channels, Illegal Hall Code Detection


The recommended cable length when using the SERVOSTAR to
source the encoder is no longer than 50 ft. (15 m). Long encoder
cables tend to have high DC resistance that may create significant
loading effects in the supply lines to the encoder. Please consider
this carefully when designing the system. An option that would
allow the use of longer lengths, implements a separate supply
located at the motor to source the encoder. Quadrature signals
returned to the drive are differentially connected which normally do
not constitute a problem with longer cable lengths.

A SERVOSTAR encoder-based system typically exhibits minimal
inaccuracies outside of the encoder itself. To get an approximate
total value the customer need only look to the specifications listed
for the encoder being used.
5.8.4 SINE ENCODER

The SERVOSTAR can receive an analog (or sine) encoder
feedback device to monitor the motor shaft position. As opposed to
a digital encoder, which generates incremental square-wave
signals, a sine encoder outputs analog differential sinusoidal
signals. These sine signals are quadrature-decoded and passed to
an interpolation circuit that breaks each 360° cycle into 256 parts
before passing it to the drive’s control board. Thus, the resolution
seen by the drive is 256 times the fundamental sinusoidal track on
the motor’s encoder. The advantage of this approach is the ability
to obtain much high encoder resolution while maintaining a
relatively low input frequency through the cable and into the
SERVOSTAR. The encoder interface includes three groups of
wires:
1. A/B (and complements) lines make up the encoder quadrature
signals. The signals are received differentially at 1V peak-to-
peak amplitudes before being processed by the interpolation
circuitry.
2. The narrow Index pulse normally appears once per mechanical
revolution and indicates a known physical position of the shaft.
This pulse is received differentially through an op amp before
being squared up and sent to the control board.

3. Upon power up, commutation signals are used to communicate

coarse position information. The first three signal types give
approximate position information so the drive can commutate
the motor forward until the Index pulse is found (There are
situations where the index signal is not available. Course
position information is used to commutate the motor
indefinitely). The fourth gives absolute information bypassing
the need for the Index signal. They are:
− No Hall signals exist if no power-up commutation signals
are available. The SERVOSTAR can excite two phases
and lock the shaft in place. It then approximates position
of the locked shaft and uses only the incremental signals
to commutate forward until the index is found.
− Hall signals provide information representing the
approximate location of the motor shaft (6 transitions per
electrical cycle of the motor). From this information, the
motor can six-step commutate forward until the index
signal is detected - at which time true position is known
and sinusoidal commutation begins. These signals are
isolated by an opto-coupler and can be differential or
open-collector type signals.
− C/D lines are an alternative to Hall signals. These lines
provide a SIN/COS sinusoidal signal where one electrical
cycle equals one mechanical revolution (identical to
single-speed resolver feedback). Interpolation is
performed on these signals: thus, absolute position is
known within 256 parts of a mechanical revolution. The
motor can commutate forward until the Index signal is
detected.
− Sine encoders with Endat capability add another approach
to communicating commutation position. Here, absolute
position information is stored in the encoder and is serially
communicated to the drive upon power up. The data is
received synchronously by a clock signal provided by the
drive. Absolute position is known immediately; therefore,
an index signal is not needed.

30
Wiring
5.8.5
ENCODER/SINE ENCODER VERSION
ENCODER TYPES AND OPTIONS VARY GREATLY. HALL n A 150 SERVOSTAR
PROVISIONS FOR OPERATING WITHOUT HALL INTERNAL
HALL n B 1K
CHANNELS USING SOFTWARE SWITCHES ARE AVAILABLE. CIRCUITRY
MOTOR THERMOSTAT MUST 150
BE CLOSED TO RUN
(SEE BELOW)
13
25
12
24 HALL 3 A OPTIONAL
11 LINE DRIVERS
HALL 3 B HALL
23 HALL 2 A (D)* HI (TRUE)
10 HALL 2 B (D)* CHANNEL HALL n B
22 HALL 1 A (C)* INPUTS
9 HALL 1 B (C)* LO (COMPLEMENT) SERVOSTAR
21 ENCODER POWER
8 COMMON HALL n A
20 +5V SUPPLY
(SEE NOTE ENCODER
06/04
7 COMMON
19 +5V 1)
6
18
5 CH B
17 CONNECTING HALLS WITH
M-SS-017-01 Rev. T
4 CH B
16 OPEN COLLECTOR
3 DIFFERENT
15 IAL
2 LINE HALL n A
14 CH A
DRIVES HALL n B
1 CH A
SERVOSTAR
MARKER PIN 18 (+5V)
MARKER COMMON
COMMON
SINE ENCODER FEEDBACK DIAGRAM
MOTOR OVERLOAD PROTECTION *INPUTS FOR SINE ENCODER THAT

HAVE C & D CHANNELS
MOTORS MUST HAVE INTEGRAL THERMAL PROTECTION OR
EXTERNAL MOTOR OVERLOAD MUST BE USED.
THERMOSTAT SWITCH MAY SEE +12 VOLTS AND 20 ma.
SERVOSTAR CD Installation
Danaher Motion Kollmorgen
Sine Encoder Requirements
Types: A, B with or without Index
A, B, Index with discrete Hall Channels
Required Signals
A, B, Index with C, D once per revolution
A, B, Endat
Signal Level: 1V peak-to-peak
Signal Type: A, B, Index Differential
C, D Differential
Endat (Data/Clock) Differential
Halls Differential or Open Collector
System Voltage 5 VDC
From encoder: 125 kHz line, 500 kHz quad
Maximum Input Frequency After Internal Drive Interpolation: 31.25 MHz line, 125 MHz
quad
Maximum Cable Length System Dependent: 50 ft. (15 m.)Recommended
Maximum Line Count per 39,000 Line counts
Motor Electrical Cycle 10,000,000 Line counts after internal drive interpolation
Maximum Supply Current
from the SERVOSTAR for 250 mA
encoders
Separate Voltage Regulator, Broken wire detector for A, B,
Protection Index, and Hall channels, Illegal Hall Code Detection, A/B
signals out of range, burst pulse overflow
Maximum Drive Internal
x256 (before quad)
Interpolation (input)

The recommended cable length when using the SERVOSTAR to
source the encoder is no longer than 50 ft. (15 m) Long encoder
cables tend to have high DC resistance that may create significant
loading affects in the supply lines to the encoder. Consider this
carefully when designing the system. An option that would allow the
use of longer lengths would be to put a separate supply at the
motor to source the encoder. Except for noise susceptibility, signals
returned to the drive are differentially connected which normally do
not constitute a problem with longer cable lengths.

Internal resolution of the system can be derived through the
following calculation:
Encoder line resolution x 256 x 4 (quadrature).
System accuracy is largely dependent upon the accuracy of the
encoder itself. To get an approximate total value, the customer
need only look to the specifications listed for the encoder being
used.

5.9 Encoder Equivalent Output

The SERVOSTAR provides a motor position output to you in the
form of quadrature encoder signals eliminating the need for an
additional position feedback device. The outputs are differential line
drivers. There is an associated DC common output (C4: pin 3)
which can connect to your port to keep common mode noise and
voltage spikes minimized for device protection. Because there are
normally differences of potential between your controller and the
drive, connection is recommended (if ground loops occur,
disconnect and retest).
The source of the Encoder Equivalent Output (EEO) signals
depends on the type of motor feedback device:
5.9.1 RESOLVER SYSTEMS

The output signal is developed through the R/D hardware circuitry
for minimal phase lag and has a maximum frequency determined
by the motor speed and R/D limits. It provides a configurable
(ENCOUT) resolution of up to 16384 lines (65536 quad counts) per
revolution of the motor shaft. The placement of the index pulse
(INDEXPOS) can be varied on resolver systems within 360
electrical degrees of the feedback signal. For single-speed
resolvers, this means you can vary the position of this signal over
one mechanical revolution. For multi-speed resolvers, the
mechanical position variation is determined by the pole-pair count
of the resolver (e.g. three-speed resolver gives mechanical
variation of the pulse within 1/3 of a revolution).
5.9.2 ENCODER SYSTEMS

The output signal is the actual encoder feedback signal that is pre-
configured (MENCRES) in the drive’s motor parameters. It can be
scaled down by multiples of two (ENCOUTO: 1, 2, 4, 8, 16) and has
a maximum frequency limit of 3 MHz.
5.9.3 SINE-ENCODER SYSTEMS

This output signal is developed for a resolution that is determined
by a divisor (SININTOUT: 128, 64, 32, 16, 8, 4, 2, 1) of the actual
sine-encoder line resolution (MENCRES). It is then encoded to a
quadrature signal before being exported out of the drive. The
maximum frequency limit is 1.2 MHz. A frequency limiter
(MSINFRQ) is provided with burst frequency fault protection.

5.9.4 EEO PHASING

The EEO signals are not phased the same for resolver and encoder
systems. The following demonstrates these phasing relationships:
5.9.4.1 RESOLVER SYSTEMS

A-Leads-B convention for clockwise rotation:
Channel A
Channel B
Index (AB high)
5.9.4.2 ENCODER AND SINE-ENCODER SYSTEMS

B-Leads-A convention for clockwise rotation
Channel A
Channel B
Index (determined by encoder)

5.9.5 RECOMMENDED MANUFACTURERS’ LIST

Schaffner Electronik AG North America
Nordstrasse 11 Schaffner EMC Inc.
CH-4708 Luterbach 9-B Fadem Road
Switzerland Springfield, NJ 07081
Phone: 065 802 626 Phone: 201 379-7778
Fax: 065 802 641 Fax: 201 379-1151
Corcom Corcom
World Headquarters East Coast Sales Office
844 E. Rockland Rd. 17 Sarah’s Way
Livertyville, Il 60048 Fairhaven, MA 02719
Phone: 708 680-7400 Phone: 508 992-4495
Fax: 708 680-8169 Fax: 508 992-3798
West Coast Sales Office
6700 Fallbrook Ave. Suite 160
West Hills, CA 91307
Phone 818 226-4306
Fax: 818 704-1757
Filter Concepts Inc. Phoenix Contact Inc.

2624 South Rouselle Street P.O. Box 4100
Santa Ana, CA 92707 USA Harrisburg, PA 17111-0100
Phone: 714 545-7003 Phone: 800 888-7388
Fax: 714 545-4607 Fax: 717 948-3475
FerriShield Interference Magnetics

Control Components
Empire State Building P.O. Box 391
350 Fifth Ave., Suite 7505 Butler, PA 16003-0391
New York, NY 10118-7591 Phone: 412 282-8282
Phone: 212 268-4020 (800 245-3984)
Fax: 212 268-4023 Fax: 412 282-6955
Fair-Rite Products Corp. Micrometals, Iron Powder Cores

P.O. Box J 5615 E. La Palma
One Commercial Row Anaheim, CA 92807
Phone: 800 356-5977
Wallkill, NY 12589 Fax: 714 970-0400
Phone: 914 895-2055
Fax: 914 8985-2629 Worldwide: 714 970-9400
E-Mail: [email protected]

Danaher Motion Kollmorgen 06/04 System Communication
6 SYSTEM COMMUNICATION
You communicate with the SERVOSTAR through either the serial
TM
port or on a SERCOS interface fiber-optic ring (SERCOS
interface versions only). The serial port can transmit data at baud
rates of 9600 or 19200 (DIP switch 6) in either RS-232 or RS-485
configurations. Multiple drives can be addressed simultaneously
when daisy chained as described later in this section.
The SERVOSTAR comes with its own software interface called
MOTIONLINK. MOTIONLINK is a Windows-based program
designed to effectively assist you in setting up and controlling the
drive’s operation. It is highly intuitive in nature and contains an
extensive context-sensitive on-line Help (F1) tool. The on-line Help
describes how to use the program in detail and serves as a
valuable reference for the drive’s variable and command set, setup
process, and troubleshooting techniques. This software package
can be downloaded from the PSP CD-ROM accompanying this
manual. Also provided on this CD-ROM is the VarCom Reference
Guide detailing the complete variable and command set. This guide
is a great added resource to MOTIONLINK when using the
package in the Terminal mode of operation.
Since the software is designed to guide the customer through the
operation process of the drive, the MOTIONLINK discussion in this
section will cover only general steps of use. A dumb terminal can
also be used to communicate to the drive. You will find this method
of communication very awkward until a certain level of familiarity
with the drive’s operation is achieved. MOTIONLINK also provides
a terminal emulation feature that contains many useful editing tools
for this type of communication.
6.1 Computer Requirements

MOTIONLINK requires an IBM-PC or compatible computer with the
following features:
− IBM-PC, XT, AT, 386, 486, PS/2, or compatible computer.
− 16 MB RAM.
®
− Windows , Windows98, or Windows NT 4.0 with Service Pack
3 or higher
− CD-ROM drive
− Standard Video Adapter (CGA, MDA, EGA, MCGA, and VGA).
− Serial Port (for communication link with SERVOSTAR). The
serial communications port may be COM1, COM2, COM3, or
COM4. COM1 is the normal configuration:
COM1: Address 3F8h, Interrupt Request #4
COM2: Address 2F8h, Interrupt Request #3
COM3: Address 3E8h, Interrupt Request #4
COM4: Address 2E8h, Interrupt Request #3

System Communication 06/04 Danaher Motion Kollmorgen
6.2 Drive Communication

Review and be familiar with this section completely before applying
power to the system.
Most drives are shipped from the factory already configured for a
particular motor. You can verify this by applying logic power and
monitoring the Status Display. A factory-configured drive will go
through a power-up sequence flashing all segments of the display
before settling out to a number indicating the mode of operation. If
the drive is not configured with a particular motor, the display will
flash a minus sign “-“ indicating that you must enter drive, motor,
and application variable parameters. The remainder of this section
describes the process of setting up a non-configured drive.
Caution must be taken when applying power
to the drive. It is factory configured to enable
upon application of power. Verify that the
hardware Remote Enable (REMOTE) enable
WARNING switch is disabled.
The SERVOSTAR has the flexibility to be addressed and controlled
from a single-line or a daisy-chain (MultiDrop) configuration in RS-
232-A, RS-485, or fiber-optic SERCOS interface. The first five
switches of the 10-position DIP located on the top of the drive sets
the binary address number for that particular drive. Switch 6 of the
DIP determines the serial communication baud rate for either 9600
BPS or 19200 BPS.
The SERVOSTAR cannot be configured for

RS-232-A and RS-485 at the same time.
NOTE
6.2.1 RS-232-A CONNECTION

The drive can be configured for a RS-232-A single-ended
connection through the C1 connector by wiring the 9-pin mating
connector. To configure for multiple units, the drives must be daisy-
chained across the C7 connectors of each drive in that chain. When
communicating to a single-line unit the drive’s DIP switch must be
set for a binary 0 address. When communicating to multiple units,
the DIP switch can be set for any binary equivalent number from 1
to 31 (see table below), as desired. You can also communicate with
any or all drives within the daisy chain configuration from any one
RS-232-A port on that chain (called Global Addressing).

6.2.2 RS-485 CONNECTION

The drive can also be configured for RS-485 differential connection
through the same C1 connector. You only need to wire the 9-pin
mating connector for RS-485. No software or hardware changes
are necessary. Setting the drive’s DIP address is identical to that
described for the RS-232.
When addressing multiple units, the drives must be daisy-chained
across C1. You cannot daisy chain across the C7 connector in RS-
485 configuration.
6.2.3 SETTING DRIVE ADDRESS
The following table shows the MultiDrop DIP switch address
settings (OFF = 0):
Drive Address Switch 5 Switch 4 Switch3 Switch 2 Switch 1
* 0 (single unit
0 0 0 0 0
addressing only)
1 0 0 0 0 1
2 0 0 0 1 0
3 0 0 0 1 1
4 0 0 1 0 0
5 0 0 1 0 1
6 0 0 1 1 0
7 0 0 1 1 1
8 0 1 0 0 0
9 0 1 0 0 1
A 0 1 0 1 0
B 0 1 0 1 1
C 0 1 1 0 0
D 0 1 1 0 1
E 0 1 1 1 0
F 0 1 1 1 1
G 1 0 0 0 0
H 1 0 0 0 1
I 1 0 0 1 0
J 1 0 0 1 1
K 1 0 1 0 0
L 1 0 1 0 1
M 1 0 1 1 0
N 1 0 1 1 1
O 1 1 0 0 0
P 1 1 0 0 1
Q 1 1 0 1 0
R 1 1 0 1 1
S 1 1 1 0 0
T 1 1 1 0 1
U 1 1 1 1 0
V 1 1 1 1 1
** Note: When the switch setting is set for binary 0, the drive assumes a single-
line serial configuration.

6.3 Sending/Retrieving System Data

The following chart describes the flow of data between the PC and
the SERVOSTAR. When logic power is applied to the drive, it loads
the variable parameters stored in EEPROM into the dynamic RAM
for fast and easy access. You can read (and write) these variable
parameters to (and from) the PC by one of several methods
described in INITIAL STARTUP
USER SETTING
VARIABLE FILE (*.SSV) MOTION LINK PC
OR TERMINAL
"DUMP" command
"LOAD" command
or Power-up
RAM (EEPROM variables) EEPROM
(operating
"SAVE" command
parameters)
MICRO-
PROCESSOR
The PC transmits serial data to the drive and stores it in dynamic

RAM. However, any variable data changed from the PC is lost
when logic power is lost, if it is not saved into non-volatile
EEPROM. Each variable listed in the VarCom Reference Guide
indicates whether it can be saved to the EEPROM.
If you are configuring the same system on similar applications, the
variables can be saved on disk in an .SSV file for convenient
downloading into other drives.
6.4 MOTIONLINK Installation

− Insert the SERVOSTAR PSP CD-ROM to load MOTIONLINK
for Windows
− The CD-ROM should AUTORUN. If not, select Start | Run (or
browse your CD-ROM drive)
− Type “D:AUTORUN.EXE” and hit the Enter key (this assumes
your CD player has a D: letter designation).
− Select a product and follow the instructions on the screen.
6.4.1 RUNNING THE PROGRAM

Go to your Start/Programs listing and select SERVOSTAR
MOTIONLINK from the menu (or click on the SERVOSTAR
MOTIONLINK icon if loaded on the desktop).

6.5 Using MOTIONLINK

MOTIONLINK gives you three methods to configure the drive. The
first uses the Startup screen and is the easiest and most highly
recommended approach. Its main purpose is for initial startups. The
second approach allows you to more indirectly perform the same
configuration as the first using the Main MOTIONLINK screen. This
method is most convenient when corrections to an existing
configuration is needed. The third method uses the Terminal Mode
screen to directly set (or monitor) values for the same variables and
commands that the other two methods configure through a more
friendly user interface. You can gain a more thorough
understanding of the SERVOSTAR drive, MOTIONLINK, and its
variable and command set by using the context-sensitive Help (F1)
provided in MOTIONLINK.
6.5.1 MOTIONLINK STARTUP WIZARD

This screen appears the first time (and any time after should you
leave it selected) MOTIONLINK is run on a PC. It is designed to
guide you through a step-by-step approach to configure a drive.
Click the START button on the first user screen and walk through
the complete sequence of buttons provided to set the drive, motor,
and application (Opmode, Tune, Backup, Go) variable parameters.
Should you de-activate this screen, it can be
reactivated by going to the Main MOTIONLINK
screen, pulling down the Configuration menu,
NOTE and selecting the New Drive (123) option.
Startup Wizard

− Setting Drive Variable Parameters: Click the Drive button. This

screen allows you to select a bus value that corresponds to the
incoming line voltage. This selection actually determines the
setting of the variable Vbus. Also included is a realtime
monitoring of the DIP switch on top of the drive so you can
verify the proper setting for the drive address, baud rate, and
various other parameters. Click Exit to return to the Startup
screen.
− Setting Motor Variable Parameters: Click the Motor button.
This screen allows you to access the MOTIONLINK motor
database. Select a motor family and then a model within that
family. Information will appear in the blank parameter fields on
the right. Click on the To Drive button beneath the fields to
send the variable parameters to the drive. Click Exit to return to
the MOTIONLINK Start-Up Wizard.
If you have a configured drive, a “From Drive”
button is provided to retrieve the motor data
already in the drive. Retrieving this data does not
NOTE erase it from the drive.
If the motor cannot be found in the database,

click on the User Define tab. Contact Danaher
Motion Customer Support for detailed
NOTE instructions.
− Customizing to Application: Click the Opmode button in the

Startup screen to select the mode of loop control desired;
position, velocity, or torque. Click Exit to return to the
MOTIONLINK Start-Up Wizard.
− Click on the Tune button in the MOTIONLINK Start-Up Wizard
to set the system bandwidth, the type of loop control, and the
filtering necessary for the application.
Caution should be used when executing
the AutoTune feature. Some applications
are not capable of handling the vibration
caused as the shaft senses its load. If this
is in question, manually tune the drive.
NOTE Also, when the load inertia is very large
and the selected bandwidth is high, this
feature may fail to perform.
− Setup Completion: Click EXIT to go to the Main MOTIONLINK
screen.
Saving Variable Parameters to EEPROM
Saving Variable Parameters to .SSV file For an explanation on these functions,
Restoring Factory Variable Parameters refer to the Main MOTIONLINK screen.
Restoring Custom Variable Parameters

6.5.2 MAIN MOTIONLINK SCREEN

This screen appears the when you exit out of the Startup screen.
All the screens mentioned in the method above can be accessed
from this screen and should be used to make corrections in the
current system configuration.
− Setting Drive Variable Parameters: From the Configure menu,

click the Drive option. The same screen appears as described
in MOTIONLINK Startup Wizard. Click Exit to return to Main
MOTIONLINK Screen.
− Setting Motor Variable Parameters: selecting the Motor option
under the Configure menu, you can obtain the same parameter
screen found in the Startup screen. Click Exit to return to Main
MOTIONLINK Screen.
− Customizing to Application: By dropping down the Operational
Mode listing, you can select the mode of loop control desired
(position, velocity, torque). Clicking the Tune button, you can
select the system bandwidth, the type of loop control, and the
filtering necessary for the application. These are the same
parameter screens found in the Startup screen. Click Exit to
return to Main MOTIONLINK Screen.
− Saving Variable Parameters to EEPROM: At the top of this
2
screen, you can click the button labeled RAM/E to save the
modified variables from RAM to EEPROM.
− Saving Variable Parameters to .SSV file: Occasionally, you
may desire to backup the variable parameters from one drive
for use in another. To do this, pull down the Edit menu and
select Backup Variables, request the information from the drive
(Receive button) into the editor, and save (Save button) the
contents in a .SSV format to a specified disk location.

− Restoring Factory Variable Parameters: To restore the original

factory variable parameters, pull down the Configure menu,
select Motor, and select the motor family and motor model.
Click the To Drive button to send the variable parameters to
2
RAM and the RAM/E SAVE button to save to EEPROM.
− Restoring Custom Variable Parameters: This process assumes
that you saved the custom variable parameters to a .SSV file,
as described above. To restore the custom parameters, pull
down the Edit menu, select Backup Variables, and click on
Open. Highlight the custom .SSV file to import variable
parameters into editor. Click Xmit to send variable parameters
to drive.
6.5.3 TERMINAL MODE

Use the MOTIONLINK Terminal Mode (or any other dumb host) to
directly monitor or modify the variable set and command the drive.
This approach should only be taken when a PC with a Windows
operating system is not available or you are well-versed with the
SERVOSTAR variable and command set.
The VarCom Reference Guide contains the complete variable and
command set. Each variable or command must be referenced for
its syntax and parameter definition. The variables and commands
are grouped by function for terminal users.
Clear EEPROM
If a “-“ does not appear and you wish to enter a new set of variable
parameters, type CLREEPROM at the terminal prompt to clear the
EEPROM memory.
Setting Drive Variable Parameters
At the prompt, enter a value for Vbus. Other drive parameters are
determined automatically.
Setting Motor Variable Parameters
Locate the motor parameter group of variables in the VarCom
Reference Guide. At the prompt, enter values for the variable
parameters listed in this group by typing the name of the variable,
space, and the numerical value.
Customizing to Application
Locate the following variable groups in the VarCom Reference
Guide:
− Analog Input-Related
− Current Parameters
− Velocity Parameters
− Position Parameters
− Loop Compensation and Gains Parameters
− Motion Control Parameters
At the prompt, enter values for the variable parameters listed in
these groups by typing the name of the variable, space, and the
numerical value. You are strongly encouraged to develop a full
understanding of these variables before finalizing the configuration.

Saving Variable Parameters to EEPROM

At the prompt, type SAVE. This saves the variable parameters
stored in the RAM to the EEPROM. All of the variables listed in the
VarCom Reference Guide indicate whether its contents can be
saved to EEPROM.
Saving Variable Parameters to .SSV file
At the prompt, type DUMP. DUMP causes the drive to output
variables and their contents to the serial port in the format of a
variable file (this includes the trailing CONFIG command). This
variable file format is an ASCII file consisting of a series of variable
assignment statements. The resulting transmission of data from the
drive can then be saved with a .SSV extension.
Restoring Factory Variable Parameters
If you have not saved any changes stored in RAM to EEPROM,
type LOAD at the prompt and the original parameters will be loaded
from the EEPROM into RAM. If changes have already been
previously saved, contact the factory to obtain a set of motor
variable parameters for the motor specified in the model number. At
the prompt, re-enter all the motor variable parameters. Type the
CONFIG command followed by the RSTVAR command.
Restoring Custom Variable Parameters
At the prompt, type RSTVAR. Transmit to the drive the custom
variable .SSV file. The contents of this file should have the CONFIG
command as its last statement. The drive executes this command
and configures itself to the transmitted parameters. Follow this by a
SAVE to store the contents into EEPROM.
6.6 MultiDrop Communication

When you run MOTIONLINK, the opening communication screen
displays a Scan For Drives button. Selecting this forces the
software to scan for any active drives (and the address location) on
the chain. Any addresses detected is then listed in the Device
Select drop-down menu at the bottom of the Main MOTIONLINK
screen. You need only highlight the desired drive to begin
communications.
To communicate with individual drives in a daisy chain from a
terminal, you must type at the prompt:
“ \ x ” <cr> where x∈{0..9, A..V, *, \}
corresponding to the DIP address setting of that desired drive. For
example, to communicate to drive #8 (DIP setting: 01000) you
would type at the prompt
“\ 8” <cr>
To globally address all drives on the chain, type at the prompt:
“ \ * ” <cr>
When globally addressing the drives, no character echo to the
terminal occurs.

6.7 Power-Up Sequence

Upon powering up, the SERVOSTAR performs a series of self-
tests. If the Status Display illuminates a solid number, no errors
were found and the EEPROM has loaded its variable parameters
(or loaded with default values in case of invalid EEPROM data) into
RAM. The Remote Enable switch on the I/O connector (C3) may
now be energized, thus enabling the servo loops.
6.8 Enabling the System

The drive enable logic is based on the following variable switches
and flags:
ACTIVE: This is the overall readiness flag indicating the
enable/disable state of the drive. If high (1), the drive is
enabled and power is being applied to motor. The
following equation must hold true for ACTIVE to go high:
ACTIVE = (READY) AND (REMOTE) AND (DIPEN)
where READY = (DRIVEOK) AND (SWEN)
READY: flag that indicates the drive is free of faults and ready to
hardware enable
DRIVEOK: switch indicates the status of the drive faults.
SWEN: switch indicates the status of the software enable (EN or
DIS).
REMOTE: switch indicates the status of the hardware Remote
Enable line on the C3 connector.
DIPEN: switch indicates the state of the DIP enable/disable switch
(#8)
Ready Flag
DRIVEOK SWEN READY
(fault status) (software enable) (drive ready)
0 (fault exists) 0 (disable) 0
0 (fault exists) 1 (enable) 0
1 (no faults) 0 (disable) 0
1 (no faults) 1 (enable) 1
Active Flag
READY REMOTE DIPEN ACTIVE
(drive ready) (hardware (DIP switch (power to the
enable) enable) motor)
0 X X 0 (no)
X 0 X 0 (no)
X X 0 0 (no)
1 1 1 1 (yes)
If the drive will not enable, check the state of the switches and flags
by clicking Status in the upper right-hand corner of the Main
MOTIONLINK screen. If using a terminal, query the drive for the
value stored in STATUS (refer to VarCom Reference Guide for an
explanation on STATUS). The Status Display indicates an enabled
drive when the decimal point is illuminated solid.

Danaher Motion Kollmorgen 06/04 SERCOS Interface Setup
7 SERCOS INTERFACE SETUP

The SERVOSTAR CD-series drives come with SERCOS interface
communication capability. It must be ordered from the factory with
this option. The Encoder Equivalent Output D9 connector (C4) is
replaced with two fiber-optic ports, transmitter (Tx) and receiver
(Rx).
This section provides the SERCOS interface-specific information
needed to complete the installation and setup of a SERCOS
interface SERVOSTAR drive to the fiber-optic ring.
7.1 DIP Switch Configuration

DIP switch configuration is similar to that of the standard
SERVOSTAR drive. Through these switches, the drive’s address
and communication power levels are set.
7.1.1 SETTING DRIVE ADDRESS

Up to 31 SERVOSTAR drives can be configured on the SERCOS
interface ring. The first five switches of the DIP set the drive
address. When the address is zero (00000), the drive operates as a
SERCOS interface repeater and as a single-axis unit with serial
communication. You can monitor and configure the drive through
the serial port. Any other address setting, 1-31 (00001 – 11111),
establishes the drive as an active SERCOS interface ring
participant with communications through the Tx/Rx ports. When the
drive has a non-zero address, you can communicate through the
serial port only for monitoring purposes.
7.1.2 SETTING TRANSMISSION POWER LEVELS

The SERCOS interface transmitter power level (DIP switch 9)
should be set according to the expected signal attenuation between
a SERCOS interface transmitter and the next receiver. Signal
attenuation is based upon cable length, cable type, and
intermediate connection losses (e.g. bulk head connectors). The
following table may be used to calculate the maximum allowable
and minimum required signal attenuation for a given power level
and cable attenuation:
Power Level Attenuation Specifications
Attenuation Low Power High Power
Maximum 9.5 dBm. + 2 m. *Ac 12.5 dBm. + 2 m. *Ac
Minimum - 1.5 dBm. + 2 m. *Ac
*Ac = Fiber optic cable attenuation in dBm./m.

SERCOS Interface Setup 06/04 Danaher Motion Kollmorgen
The maximum and minimum cable lengths may be calculated by
dividing the maximum and minimum signal attenuations by the
cable attenuation. The following table shows the cable lengths for 1
mm plastic fiber with an attenuation of 0.18 dBm/m:
Cable Length Specifications
Length Low Power High Power
Maximum 54.7 m 71.4 m
Minimum - 10.3 m
1) Fiber optic cable attenuation is 0.18 dBm/m.
2) Cable length calculations assume that the fiber is not attenuated by intermediate
connections.
For most applications, the low power setting is sufficient. Longer

cable runs or the use of intermediate connectors may require the
high power setting. Communication problems may occur if the
power level at the receiver is too large or too small. Receiver power
problems may cause erroneous data transfer resulting in the drive
returning to CP0, or failure to advance out of CP0.
For more information on SERCOS interface signal attenuation,
refer to the following sections of the IEC 61491 SERCOS interface
specification:
− 5.3 - Optical Signals on the Transmission Line
− Annex G: Attenuation on the Transmission Line
7.2 Status Display

After the CP run-up sequence has completed, the drive will be in
OPMODE 5 when communicating on a SERCOS interface ring.
This is indicated by the number 5 on the status display. The
SERCOS interface version of the SERVOSTAR differs from the
standard unit in that errors and faults are not communicated
through this display (only through the SERCOS interface ring to the
controller). If an error occurs, the 5 remains on the display. The
status display decimal point operates identically to that of the
standard unit in that it turns ON and OFF when the drive is enabled
or disabled.
The SERCOS interface version of the

SERVOSTAR is not automatically enabled on
power-up, no matter what the address.
NOTE

7.3 Connection
The mating connector selected for the Tx and Rx ports follow the
IEC 874-2 specification, which recommends an F-SMA type
connector. A hand-tight connection is adequate.
Danaher Motion offers 30, 60, and 100cm plastic fiber optic cables
with SERCOS interface compatible F-SMA connectors. The
following specifications provide general cable information:
Cable Characteristics Specifications
Cable Type 1mm plastic
Attenuation ≤0.18 dBm/m
Fiber NA 0.47
Temperature -55º C to 85º C
Jacket material PVC
Jacket OD 2.2 ± 0.07 mm
Tensile Strength 7 kg
Refer to the following IEC 61491 specification for more connector

and cabling information:
− 5.2.2 Structure of the Transmission Lines
− 5.3.3 Fiber Optic Cable
− 5.3.4 Connectors
7.4 Communication
The SERVOSTAR SERCOS interface drive offers two
communication approaches for drive configuration. The first
approach is to communicate, via a multi-axis SERCOS interface
controller, all the drive parameters through the fiber-optic ring
during the CP2 and CP3 run-up stages. This requires a broad
understanding of the controller functionally and knowledge of the
SERCOS interface standard and manufacturer’s IDN set. The
standard and manufacturer IDNs supported by Danaher Motion are
functionally categorized to make this method of configuring easier.
The second approach gives you the ability to configure each axis
separately through the serial port using MOTIONLINK.
MOTIONLINK is very intuitive and guides you through the setup
stages of the configuration process. It provides interactive setup
screens for easy manipulation of the drive’s parameters while
giving you realtime monitoring and recording tools that help in
optimizing axis performance. Once performance is optimized, the
parameters can be stored in the drive’s EEPROM memory before
establishing communication through the SERCOS interface.

7.4.1 DRIVE CONFIGURATION

Before you can begin the CPx (where x = 0,1,2,3,4) run-up process,
the drive should be configured and tuned for the axis of operation.
To accomplish this, follow the guidelines below:
1. Power down the drive.
2. Set the drive address to zero for single-axis operation.
3. Select a serial baud rate.
4. Connect a serial cable from the drive to a host.
5. Power up the drive
6. Install MOTIONLINK and communicate with the drive.
7. Follow the user screens to configure the drive and motor
combination.
8. Enable the drive.
9. Tune the system as desired.
10. Save the drive parameters to EEPROM.
11. Power down and reset that actual DIP address. Any non-zero
address sets the drive for communication on the SERCOS
interface ring. Each drive on the ring must have a unique non-
zero address.
12. Set the SERCOS interface baud rate (DIP switch 6 off/on for
2/4 Mbits/s)
13. Depending on the ring configuration, link the fiber optic cables
from drive-to-drive or drive-to-master as follows: Tx1 to Rx2,
Tx2 to Rx3, etc.
14. Power up the drive. It is now prepared to move through the
SERCOS interface communication phases under the master’s
control.
7.4.2 CP RUN-UP
Upon power-up, the status display should alternately flash a P and
a 0 to indicate SERCOS interface communication phase 0. As the
drive moves through each communication phase, the display
alternately flashes a P and a number indicating the next sequential
communication phase (phase 0-4). Upon reaching communication
phase 4 (CP4), the display briefly flashes P and 4 before displaying
a steady state 5. This indicates that the SERCOS interface is
initialized and the drive and motor system are ready for
commanding motion.

7.4.2.1 CP2 INITIALIZATION

IDN 18 contains a list of IDNs that must be written to the drive in
CP2. The CP2 transition procedure (IDN 127) verifies the drive’s
readiness to transition from CP2 to CP3 and checks whether each
IDN listed within IDN 18 has been written by the master. If any IDN
has been written with illegal values, then the drive will not allow a
transition to CP3. If the drive fails to transition, then IDN 21 will
contain a list of IDNs that are not configured properly. The following
IDNs should be configured during CP2:
IDN Description
2 Communication cycle time (tncyc).
6 AT transmission starting time (t1).
9 Position of data record in MDT.
10 MDT length.
89 MDT transmission starting time (t2).
Some masters do not support toggling the control unit

synchronization bit (MDT control word, bit 10) during CP3
and CP4. In this case, initialize the control unit
synchronization bit monitoring IDN (P152) to 0 during CP2.
NOTE Refer to the IDN descriptions for more information.
7.4.2.2 CP3 INITIALIZATION

IDN 19 contains a list of IDNs that must be written to the drive
during CP3. If the drive was properly configured using
MOTIONLINK, IDN 19 should be empty and the master requires no
IDN initialization during this phase.
7.4.2.3 OPERATIONAL NOTES

− Remember that the hardware enables, DIP switch 8 and the
Remote Enable line must be enabled before the drive can be
system enabled through the MDT control word during CP4. If
system enabling fails, refer to IDN P15 for a list of conditions
that prevent this action.
− If a fault occurs, the drive will not allow the master to clear
faults while any of the MDT control bits (13-15) are set.
− SERCOS interface Torque Units:
Standard SERCOS interface torque units are based on 0.1% of
motor continuous current. However, when using
MOTIONLINK, the torque units are based on 0.1% of drive
peak current.
− SERCOS interface Velocity Units: counts/CUCT * 256
The following formulas may be used to convert to and from the
SERCOS interface units and rpm.
Vel {rpm} = Vel {cnts/CUCT * 256} * 1875 / (8 * Cnts * CUCT)
Vel {cnts/CUCT * 256} = Vel {rpm} * 8 * Cnts * CUCT / 1875

7.4.2.4 EQUATION NOTES

1. Cnts = the number of encoder (or resolver equivalent) counts
per revolution.
where: Encoder counts = Encoder lines * 4.
Resolver counts = 2^16 * MResPoles/2
2. CUCT = The control unit cycle time (IDN 1) in mS.
3. The units "CUCT/ms" is the number of CUCT periods per ms.
For example, a 2 ms CUCT has 1/2 a CUCT/ms.
− Remember the following when monitoring a SERCOS
interface drive through the serial port:
− The SERCOS interface address is also the serial
MultiDrop address
− SERCOS interface operation changes the UNITS
variable to internal units
− The SERCOS interface version of the SERVOSTAR
is not enabled automatically on power-up, even with
the drive address set to 0.

Danaher Motion Kollmorgen 06/04 System Operation
8 SYSTEM OPERATION
The SERVOSTAR has a seven-segment indicator, called a Status
Display that indicates four types of states: Power-up, Steady State,
Flashing State, and Momentary State. The decimal point directly
relates to the global drive enable.
Status Display
DRIVE STATE DISPLAY APPEARANCE
Momentarily illuminates all display segments
Power-up
(forming an 8) and the decimal point.
Steady State Displays the operational mode (OPMODE) of the
(No Faults) drive (0-8).
Used to indicate an abnormal operating state:
If the position hold feature is active, the OPMODE
number flashes at a 1 Hz rate.
If a fault was detected, a flashing code is
displayed to identify the fault. Some codes consist
of a sequence of two or more digits (see
Flashing State
Troubleshooting). In general, these faults cause a
latched disable (sometimes controllable through
software switches). To clear fault, toggle remote
enable (except for over-current).
If the encoder initialization function (ENCSTART)
is active, the OPMODE number flashes at 3 Hz.
Displays a character momentarily for 500 ms
before returning to the steady state. The timer is
Momentary Fault resetable.
C = Communications Error
F = Drive is in FoldBack mode
Status Display Decimal Point

DECIMAL POINT STATE DRIVE STATUS
Steady OFF No power to the motor
Steady ON Drive enabled, power to the motor
Drive enabled, power to the motor,
Flashing but a motor safety feature has been
disabled (for example, LIMDIS = 1).
8.1 Operational Modes

The SERVOSTAR has the ability to assume different modes of
operation. It is factory configured in OPMODE 1 (Analog Velocity
Controller) but may be reconfigured. Not all commands and
variables are active or meaningful in every OPMODE.
1. Serial Velocity Controller (OPMODE = 0): the SERVOSTAR is
configured as a velocity-loop controller and is controlled by
issuing a velocity command (J: jog command, or STEP: step
command) to the drive via the serial port.
2. Analog Velocity Controller (OPMODE = 1): the SERVOSTAR
is configured as a velocity-loop controller and is controlled
through either a ±10 V analog input signal or jog (J) commands
stored in the Configurable I/O. The commanded velocity is
proportional to the input voltage.

System Operation 06/04 Danaher Motion Kollmorgen
3. Serial Torque (Current) Controller (OPMODE = 2): the

SERVOSTAR is configured as a torque-loop controller and is
controlled by issuing a current command (using the T
command) to the drive via the serial port.
4. Analog Torque (Current) Controller (OPMODE = 3): the
SERVOSTAR is configured as a torque-loop controller and is
controlled via a ±10 V analog input signal. The commanded
current is proportional to the input voltage.
5. Gearing Position Controller (OPMODE = 4): the SERVOSTAR
is configured as a positioning controller that can operate in one
of three settings (Encoder Follower, Pulse/Direction, Up/Down
Counter). The setting used is determined by the GEARMODE
variable.
6. Position Controller (OPMODE = 8): the SERVOSTAR is
configured as a serial or an analog positioning controller,
depending on the value of PCMDMODE, that can receive
simple absolute, incremental, indexing, homing, and analog
commands.
7. SERCOS interface Controller (OPMODE = 5): the
SERVOSTAR must be ordered from the factory as a SERCOS
interface unit to establish communications in this OPMODE.
The drive is shipped with Connector C4 as the
Transmit/Receive port (no longer the Encoder Equivalent
Output).
8.2 System I/O

This section discusses the I/O features of the C3 connector (except
for the Thermostat input on C2). For further explanation on how to
®
use these features, refer to the SERVOSTAR CD VarCom
Reference Manual.
8.2.1 EXTENDED I/O

The SERVOSTAR CD Series 5 hardware has 3 additional digital
inputs in addition to the standard I/O. These inputs are accessible
through the 20-pin connector located on the top of the drive. The
pins on this connector are arranged in two rows (A & B) of 10.
®
For information on the new commands, refer to the SERVOSTAR
CD VarCom Reference Manual.

8.2.2 ANALOG INPUT (ANIN)

The position, velocity, or torque loop can receive its command from
an analog voltage source and is selectable through the OPMODE
variable. The analog input to the SERVOSTAR is differential. This
means that the signals received at the two inputs are subtracted
from each other to create a ‘difference’, which is then used to
command the rest of the system. This type of input has a high
degree of noise immunity and, in many cases, will allow for ground
isolation between systems. This analog input also has a low pass
filter (ANLPFHZ) to prevent high frequency noise from entering the
system.
The input voltage from the differential receiver is applied to a
precise 14-bit Analog-to-Digital (A/D) conversion system. The A/D
conversion system is read by the microprocessor every 500 µs for
the position loop modes, every 250 µs for the velocity loop mode,
and every 62.5 µs for the torque (current) loop mode of operation.
Encoder-based units come with the additional benefit of a Dual
Gain (ANDG) input. When enabled, the system uses two 14-bit A/D
inputs to read the user-supplied analog signal. One input is a direct
reading of the ±10 V signal, while the other incorporates a 2x gain
term. When the input voltage is less than 4 V, the 2x channel is
used to determine the input voltage, which extends the resolution to
a 15-bit equivalent. Above 4 V, the system uses the straight 14-bit
conversion. Special software algorithms are used to minimize
cross-over distortion and add 0.25 V of hysterisis.
Analog systems often require scaling and offset bias. The
SERVOSTAR adds an analog offset (ANOFF) variable to this
reading, performs an analog deadband (ANDB) adjustment, and
scales it through the either the position loop input scaling (GEARI,
GEARO), velocity loop input scaling (VSCALE), or torque loop
input scaling (ISCALE) before passing the data to the selected
control loop. The analog input (ANIN) variable indicates the analog
reading after the offset (ANOFF) and the deadband (ANDB)
adjustments but before the loop scaling. The ANIN range is ±22500
counts (or mV).
The SERVOSTAR also offers an automatic analog input zeroing
function. Invoking ANZERO while the drive is enabled or disabled
samples motor velocity over a 32 ms period and updates ANOFF
accordingly to the analog input offset. This command also
incorporates an internal offset mechanism that has finer resolution
than ANOFF is capable of providing.

8.2.3 REMOTE ENABLE INPUT (REMOTE)

The opto-isolated remote enable input (REMOTE) provides a
hardware drive enable switch. This 12 VDC to 24 VDC input
disables or enables the power stage output to the motor. The signal
must be customer-supplied in order to get the drive to enable (in
combination with other parameters; ACTIVE) and operate. Tapping
the signal off the logic supply (C5) is not recommended. The
toggling of this switch will also initiate an attempt to recover from a
fault condition. It can also be used to trigger various position
homing features (HOMETYPE).
8.2.4 CONFIGURABLE INPUTS (IN1, IN2, IN3)

These 12 VDC to 24 VDC inputs are defined by the INxMODE
variable. Placing the appropriate value in INxMODE (See the
VarCom Reference Guide for details) sets up the inputs to be used
for such features as CC/CCW hardware position limits, Electronic
Gearing, serial and analog position triggering (for incremental
moves and homing), fault output relay configuration, MOTIONLINK
scope triggering, and more. When set for the CC/CCW hardware
position limits, the inputs prevent any further motor travel in their
respective direction but do not disable the drive or prevent motion
in the opposite direction. Note that if acceleration control is in place
(PROFMODE = 1), the motor will ramp to a stop after the opening
of the End Travel Limit. These inputs are opto-isolated and
considered active enable, meaning current must flow through these
signals to allow the system to operate. This provides a ‘dead-man’
safety feature. Energizing both the CW and CCW hardware position
limits causes the SERVOSTAR to enter the HOLD mode. These
inputs can also be inverted (ININVx, where x = 1, 2, 3).
The default settings of these inputs are for the
hardware position limits. The Status Display may
flash an ‘L’ upon power-up indicating that a travel
limit has been tripped. If these position limits are
CAUTION not in use, set LIMDIS=1.
8.2.5 CONFIGURABLE OUTPUTS (ANOUT, O1)

The ±10 V, 12-bit analog output (ANOUT) is normally off
(monitoring). The setting of this variable will allow you to meter
various feedback quantities such as velocity, current, horse power,
position feedback and following error, and more. This pin must be
referenced to DC Common (pin 4).
The digital output (O1, O1MODE) can be toggled in an On/Off state
to indicate various drive, motor, and variable conditions. These
include: absolute speed and current levels, FoldBack conditions,
motor braking, motion complete and zero speed conditions, position
overshoot flagging, programmable limit switch detection, and an
enable (ACTIVE) flag. Condition, reset, and triggering levels are
established through O1MODE, O1RST, O1TRIG.

8.2.6 FAULT OUTPUT RELAY (RELAY,

RELAYMODE)
The SERVOSTAR provides a drive ready/drive up output in the
form of a relay (RELAY) output. The relay output is controlled by
the SERVOSTAR’s microprocessor. There is a software switch
(RELAYMODE) that configures the relay output to act as a ‘Drive
Ready’ or ‘Drive Up’ indicator:
If RELAYMODE = 0, the relay is closed when the drive is error free
and ready to run. This is a ‘Drive Ready’
configuration.
If RELAYMODE = 1, the relay is closed only when the drive is
enabled. This is a ‘Drive Up’ configuration.
If RELAYMODE = 2, the relay opens during a fault when the drive
is disabled.
You can program this fault output to open on any

system fault by triggering the Configurable Inputs
(IN1MODE, IN2MODE, IN3MODE, IN1, IN2, or IN3)
NOTE
8.2.7 MOTOR THERMOSTAT INPUT

The SERVOSTAR provides a motor thermostat input on the C2
connector that is configured for different types of thermal
protections (THERMTYPE), as well as manipulation of how the
drive responds to a motor thermal condition (THERM, THERMODE,
THERMTIME). Danaher Motion GOLDLINE motors and cables
connect the thermostat through the feedback cable. The input to
the SERVOSTAR is electrically closed through the thermostat for
proper operation. The drive normally flashes an H in the status
display when this input is electrically opened.
If a motor thermal device is not used, set
THERMODE to 3 to disable the feature (turns the ‘H’
status display indicator off).
NOTE
8.3 Control loops

This section describes the servo control loops, their characteristics,
and how to configure them.
8.3.1 CORE PROCESSORS

A 40 MHz embedded controller and a 40 MHz DSP controller are
the heart of the SERVOSTAR. They use its internal operating
system to monitor inputs, adjust outputs, communicate serially,
maintain servo control, and monitor faults. The flash memory
firmware controls the core processor and gives the SERVOSTAR
its operating characteristics saved in EPROM.

The version number of the firmware is read using VER. When
calling for technical support, have the firmware version number
readily available. The most recent version of firmware is available
for purchase and is easily field-upgradable through a PC. It is
obtained by contacting a sales representative or Danaher Motion
Customer Support.
8.3.2 SERVO LOOP DESCRIPTION

The SERVOSTAR provides high performance motor control by
controlling up to four distinct closed loop systems within the DSP:
the current, commutation, velocity, and position loops. Control
Loops depicts the control loops graphically.
Control Loops
P O S IT IO N L O O P
V E L O C IT Y L O O P
C O M M U T A T IO N L O O P
C U R R EN T LO O P
330VD C
I
S
O
L PO W ER
PCM D A TRANS- M
T IS T O R S
I
O R
N
dp
dt
8.3.2.1 CURRENT LOOP

Since current and torque are proportional in a Permanent Magnet
(PM) motor, the current loop is often referred to as the torque loop.
The function of the current loop is to regulate motor current as
directed by a current command signal. The current command signal
from the microprocessor can either come from a direct user input
(OPMODE 2 & 3) or from the output of the velocity loop. There are
actually three current loops, one for each motor phase. Each
current loop receives its own command input from the commutation
loop.
The SERVOSTAR uses a fully digital, pole placement current loop
with high bandwidth and a current loop sampling rate of 16 kHz
(62.5 µs.). All coefficients of the current loop are digitally calculated
inside the drive for a given set of motor and drive characteristics.
The current loop also includes adaptive gain terms to compensate
for some non-linear effects.
The current loop incorporates electrical isolation for protection from
the high-voltage bus. These current loops also convert the output
voltage to a Pulse Width Modulated (PWM) signal providing the
highest efficiency possible. The PWM center frequency can be 8 or
16 kHz according to the drive size.

8.3.2.2 COMMUTATION LOOP

This loop converts a single-phase current command signal into a
three-phase, position-modulated sine wave input to the current
loops. The SERVOSTAR has a patented sinusoidal wave form
generator, which uses a technique called Torque Angle Advance to
get top performance out of its motors. The waveform generator is
part of the microprocessor and is updated at a 16 kHz rate. This
provides hi-fidelity sinewave commutation at both low and high
velocities. The sinewave output must be aligned to the back EMF
(MOTORBEMF) characteristics of the motor. This is why resolver
or encoder alignment to the motor is critical.
8.3.2.3 VELOCITY LOOP

The purpose of the velocity loop is to regulate motor speed. Like
the current and the commutation loops, the velocity loop is fully
digital and uses the resolver or the encoder feedback signals to
calculate actual motor velocity. The command for the velocity loop
can come from a direct user input (OPMODE’s 0&1) or can be the
output of the position loop. The velocity loop is a digital sampling
system operating at 4 kHz.
The difference between actual and desired velocity is filtered
through a compensator algorithm and fed to the commutation loop.
The SERVOSTAR offers four velocity compensators (methods of
regulating velocity) and are selectable through the COMPMODE
variable. The four are: Proportional-Integral (PI), Pseudo-
Derivative-Feedback with Feed-Forward (PDFF), Standard Pole
Placement, and Extended Standard Pole Placement.
8.3.2.4 POSITION LOOP

The final control configuration is the position loop. The purpose of
this loop is to maintain motor shaft position. Like the previous loops,
the position loop is fully digital and uses resolver, encoder, and sine
encoder feedback signals to determine actual motor position. The
drive can also accept a position signal from an external feedback
device (e.g., load encoder). It samples at a rate of 2 kHz and can
be configured for three different modes of operation:
OPMODE 4: This mode of operation sets the SERVOSTAR up to
run as a pulse (or master encoder) follower by using the Electronic
Gearing feature. The pulse input can either be applied through the
Configurable Inputs on the C3 connector (up to 2.5 kHz max. -
opto-isolated) or through the Remote Encoder Input on the C8
connector (up to 3 MHz) on top of the drive.

OPMODE 8: This mode of operation configures the SERVOSTAR
as a simple positioning controller. Once in this mode, position
commands can be given through the serial port, through the
Configurable I/O, or through the analog input (determined by the
PCMDMODE variable). The position loop has been enhanced to a
full PID controller with acceleration and velocity feed-forward gains.
Two integral gain variables have been added to limit the action of
the integral term during selected parts of the profile. This helps to
minimize overshoot and settling problems.
Using a serial command (PCMDMODE=0), the SERVOSTAR
executes simple absolute, incremental (or indexing), and homing
motion profiles. This is done either by direct commands through the
serial port (MI, MA, MH) or by pre-configuring a profile in memory to
be used in conjunction with the Configurable I/O (MASPEED,
MISPEED0=3, MAPOS, O1, O1MODE, INx, INxMODE).
Using an analog command (PCMDMODE=1), the SERVOSTAR
scales the analog input (GEARI, GEARO) to establish a wide range
of relationships between an analog input adjustment and a
corresponding shaft movement. Homing types (HOMETYPE) are
available that home to a particular analog input level (and position
count), triggering either through the Configurable Inputs or the
Remote Enable.
In this mode of operation, the drive can also accept an external
load feedback signal through the C8 connector (DUALFB=1). This
helps eliminate the positional inaccuracies, due to gear backlash
and poor coupling, by positioning according to the load’s position
(not the motor shaft’s position).
The SERVOSTAR also operates in the position mode when the
drive is in the hold position state (HOLD = 1).
8.3.3 TORQUE LOOP OPERATION

The SERVOSTAR has many internal variables that are used to
examine and dictate system operation. Many of these variables and
their locations in MOTIONLINK are presented graphically in the
following discussions to help disclose meanings and relationships.
8.3.3.1 SERIAL TORQUE

The SERVOSTAR can be operated as a serial torque-controlled
amplifier (OPMODE 2). It receives a serial command (T) via a host
to a command generator, which in turn creates a current command
(ICMD). The current (or torque) command is checked against peak
(IMAX, ILIM) and continuous (FoldBack features, ICONT) current
clamp limits.
Sinusoidal commutation modulation is added to the command and
fed to the three-phase current loop regulator, which calculates a
current error. This error is then fed through a digital pole-placement
compensation algorithm.

The output of the compensator is converted to a PWM signal and

fed to the power transistor bridge. The actual motor current is
updated and the process begins again. The following graphic is a
representation of the serial torque loop operation (refer to the
VarCom Reference Guide for details on all variables and
commands).
Control Limits
IMAX (DIPEAK/ MIPEAK)
Serial Command Command ICONT (DCONT / MICONT) ICMD Compensator based on
Generator ILIM, ILIM2 motor parameters
FOLD, FOLDTIME, FOLDMODE
MFOLD, MFOLDDIS, MFOLDD, MFOLDT, MFOLDR
IA IC
IISCALE ANOUT
DVM
1 OR 3
8.3.3.2 ANALOG TORQUE

The SERVOSTAR can be often configured to operate as an analog
torque loop controller (OPMODE 3). In this case, the current loop
receives its input from the analog-to-digital (A/D) conversion
system. After conversion, the input command signal is processed
through an algorithm which adjust the signal (ANOFF, ANDB,
ANZERO), filters it (ANLPFHZ) and then scales it (ISCALE), before
developing the current command (ICMD). The current (or torque)
command is then checked against peak (IMAX, ILIM) and
continuous (FoldBack features, ICONT) current clamp limits.

Sinusoidal commutation modulation is added to the command and

then fed to the three-phase current loop regulator, which calculates
a current error. This error is then fed through a digital pole-
placement compensation algorithm. The output of the compensator
is converted to a PWM signal and fed to the power transistor
bridge. The actual motor current is updated and the process begins
again.
8.3.4 CURRENT SAMPLING

The current loop receives corrective feedback from the current
sampling circuitry. The current sensors use closed-loop hall
sampling techniques in all units.
The current sample is used by the current loops to regulate the
current in each of the three motor phases. Two phases (A and C) of
the current signal are sampled by the microprocessor at a 16kHz
rate. The momentary A phase current and C phase current can be
monitored by examining IA and IC, respectively. The
microprocessor calculates the equivalent absolute current, which
can be monitored as I. This value can be averaged for 2, 4, 8, 16,
32, or 64 samples.

8.4 Foldback
The SERVOSTAR offers two types of FoldBack protection for both
the motor and the drive. The drive’s microprocessor monitors the
current feedback signal and develops an RMS value of this signal
for the purpose of providing a value that represents the current in
the motor. The system is similar to an I-squared-T accumulator.
8.4.1 DRIVE FOLDBACK

This FoldBack algorithm monitors current feedback and, if the
feedback exceeds the continuous current rating of the drive/motor
combination (ICONT), decreases the system’s current to the
ICONT level. For example, under a step command input condition,
the FoldBack algorithm will allow maximum peak current (IMAX)
output from the drive for ½ second for Cx units. after which the
drive enters FoldBack mode (FOLD = 1) and begins an exponential
FoldBack to the system’s continuous current. It will take
approximately six seconds for the exponential decay to drop from
the system’s peak current to its continuous level.
For drive currents that exceed ICONT, but are
below IMAX, the system period before FoldBack
occurs is extended beyond two seconds. Two
seconds is the shortest time period that will elapse
before the drive enters FoldBack and only occurs
NOTE when maximum peak current (IMAX) is drawn.
This FoldBack feature is designed to protect the
drive electronics, not the motor. The Configurable
Output, O1, (pin 12) can be configured to indicate a
drive FoldBack condition.
NOTE
8.4.2 MOTOR FOLDBACK

This FoldBack algorithm is designed to provide motor protection in
cases where the drive’s continuous current rating is above the
motor’s continuous rating. This combination is often desired in
applications where maximum peak motor torques are required.
However, the possibility exists that the drive could source current
on a continuous basis indefinitely to the motor and would force it
beyond its thermal capability. Unlike the drive FoldBack, you have
complete configurability over this feature (MFOLD, MFOLDD,
MFOLDDIS, MFOLDR, MFOLDT).

8.5 Encoder Simulation

The encoder simulation signal is generally generated in the A-quad-
B format. The addition of ENCOUTMOD enables you to change this
format to a pulse up/down signal.
8.6 Encoder Initialization

In brushless 3-phase motors, the torque generated by the motor
depends on the three-phase currents and motor position. In order
to properly control the motor and extract maximum torque out of the
available motor and power stage, the controller must be provided
with the current motor position. In encoder-based systems, the
initial position for commutation initialization is found using hall
sensors switching, index finding, or an appropriate commutation-
lock algorithm (or a combination of the three methods). Encoder
initialization without motion uses a commutation-lock algorithm.
On power up, since the absolute motor position is unknown, two
methods may be implemented:
− Applying a forced commutation to move the motor to a
predetermined position where the torque generated is zero and
updating controller variables accordingly.
− Using a motion control algorithm that brings the commutation
angle of the motor from the initial, unknown position to the
current motor position (instead of moving the motor).
The first method is currently implemented on the SERVOSTAR CD.
The disadvantage of this method is that it requires the motor to be
moved. This produces a jumpy motion that may not be tolerable in
some cases (such as linear motors applications).
The second method is designed to solve this problem by
implementing a closed loop commutation-lock algorithm that
adjusts the commutation angle to the motor position rather than
moving the motor to a predetermined place. The motor moves very
slightly. Motion of at least ±4 electrical degrees is expected.

8.6.1 THE PROCESS

1. Disable the drive.
2. Select the encoder initialization process by entering the
instruction, INITMODE 2.
3. Set the encoder initialization current using IENCSTART. Set
this to the maximum allowed application current.
4. Set the gain for the process using INITGAIN (typically 1000).
5. Initialize the process by using ENCSTART.
6. Enable the drive.
7. Monitor the process by reading the status word, STATUS2,
and the status of ACTIVE.
If the process completes successfully, the drive is enabled, and

ACTIVE = 1. If the process is not successful, bit 2 in the first word
of STATUS2 is set.
8.7 Sine/Cosine Calibration

The software Sine Encoder and software resolver algorithms are
based on sampling the incoming sine and cosine signals. The
accuracy of the process depends on the sampling accuracy of the
sine and cosine values. In order to prevent accuracy degradation
due to electronic component tolerances, the sine and cosine values
must be gain- and offset-compensated.
The process of finding the gain and offset compensation
parameters is called Sine Zero. The process matches an amplifier
to an encoder or resolver after replacing a motor or an amplifier.
After the process terminates the gain and offset values are stored
in the non-volatile memory, they are loaded each time the amplifier
is powered on.
The process includes finding 128 maximum and minimum, Sine
and Cosine peaks and calculating the average gain and offset
values. Due to accuracy restrictions, the motor must be rotated at a
slow speed so the Sine/Cosine waves generated are at a frequency
low enough for a valid result. The speed must be such that the
frequency of the Sine/Cosine signals does not exceed 250Hz. For a
rotary motor, the maximum motor speed in rpm is calculated as:
60 x 250 / (MENCRES x MSININT)
For a linear motor, the maximum motor speed in mm/sec is
calculated as:
250 x MPITCH / (MSININT x MENCRES)

8.7.1 THE PROCESS

During calibration, the motor is either moved manually or under
servo control (preferably under velocity control). Take the following
steps:
1. Initialize the process with SININIT (without parameters)
2. Move the motor in either direction. While moving the motor,
query the status using SININIST.
3. The process is complete when SININIST returns a value of 3
(done) or 5 (fault).
8.8 Software Resolver Interface

The resolver-to-digital (RDC) conversion is accomplished in the
Series 5 products using software techniques, as opposed to using a
dedicated integrated circuit. The benefits of this mechanism
include:
− Enhanced system performance because the resolution is not a
function of the velocity.
− Increased accuracy due to the ability to calibrate and match
the Sine and Cosine signals.
− Increased reliability due to the use of fewer components.
8.8.1 THE PROCESS

The software resolver implements a second-order tracking filter that
uses feed-forward to zero (ideally) the tracking error for constant
speed. RESBW is the filter bandwidth and the tradeoff is: the higher
the bandwidth, the faster the response and the more the system is
prone to noise.
The Sine and Cosine signals of the resolver are calibrated to
increase the accuracy of the measurement. The calibration process
is described above in Sine/Cosine Calibration. This process is
initialized automatically at each power up. Old parameters are used
until the calibration process generates new parameters so there is
no need to explicitly enter SININIT.

Danaher Motion Kollmorgen 06/04 System Description
9 SYSTEM DESCRIPTION
The SERVOSTAR CD is a digital servo motor amplifier that meets
the needs of many servo applications such as machine tooling,
packaging, electronic assembly, and document handling. It has
been designed to be a multifaceted amplifier, capable of driving
Danaher Motion’s vast product basket of motors and their assorted
feedback devices. A C-series (Compact Drive that includes an
integrated bus module), is available in 3, 6, and 10 amp sizes. All
are packaged in a small frame size for minimizing cabinet space.
This product can be commanded through analog, serial, and
SERCOS interface user interfaces and has its own tailored
software environment in Danaher Motion’s MOTIONLINK for
Windows.
9.1 Product Features

The SERVOSTAR CD includes a vast array of features. Its various
control techniques, interfaces, and user tools give the customer a
compatible drive to meet most motion control applications. User
features include:
Bulleted words that begin in capital letters
indicate formal feature names. Words that are
capitalized indicate the software variables and
commands associated with the feature. This
section is designed to direct you to the VarCom
NOTE Reference Manual for details on these features.
9.1.1 CURRENT/TORQUE CONTROL

− Digital current loop control (Torque Mode - OPMODE 2 or 3)
receiving serial (T) or analog commands.
− Pulse Width Modulated (PWM) sine wave commutation
(PWMFRQ) providing smooth and precise low-speed control
and high-speed performance.
− Current loop adaptive gain (MLGAINC, MLGAINP, MLGAINZ).
− System current-limiting capability (ILIM, ILIM2, IMAX,
MICONT, MIPEAK).
− Exponential current vs. Time limiter (FOLD, FOLDMODE).
− Back EMF compensator (MBEMFCOMP).
9.1.2 VELOCITY CONTROL

− Digital velocity loop control (Velocity Mode - OPMODE 0 or 1)
receiving serial (J), analog (ANIN), or I/O triggered commands
(MISPEED1, MISPEED2, MISPEED3, IN1, IN2, IN3,
IN1MODE, IN2MODE, IN3MODE).
− Velocity stepping and jogging capability (STEP, J).

System Description 06/04 Danaher Motion Kollmorgen
− Serial control through stored commands triggered through the

Configurable I/O (IN1, IN2, IN3, IN1MODE, IN2MODE,
IN3MODE).
− Automatic control loop tuning through the auto-tune feature
(TUNE).
− Configurable application and system speed limits (VLIM,
VOSPD, VMAX).
− Advanced control algorithms (COMPMODE):
− Proportional-Integral (GV, GVI).
− Pseudo-Derivative with feed forward (KV, KVI, KVFR).
− Standard Pole Placement (BW, MJ, LMJR, TF).
− Extended Standard Pole Placement (BW, MJ, LMJR, TF).
− First- and second-order low pass filtering capability
(FILTMODE, LPFHZ1, LPFHZ2, COMPFILT).
− Notch filtering capability (FILTMODE, NOTCHHZ,
NOTCHBW).
− Bandwidths up to 400 Hz.
− On-the-fly homing capability (HOMETYPE) in analog velocity
mode (OPMODE 1) through either the Configurable Inputs or
terminal.
− On-the-fly switching between velocity and current/torque
control (IN1, IN2, IN3, IN1MODE, IN2MODE, IN3MODE).
9.1.3 POSITION CONTROL

− Serial positioning loop control (Position Mode - OPMODE 8 &
PCMDMODE) receiving serial or I/O-controlled command (IN1,
IN2, IN3, IN1MODE, IN2MODE, IN3MODE).
− Analog positioning loop control (Position Mode - OPMODE 8 &
PCMDMODE) over a ±10 V range with scaling capability
(PSCALE, GEAR, GEARI, GEARO) and I/O triggering.
− Incremental and absolute positioning with an in position
indicator (MI, MA, INPOS, PEINPOS).
− Simple absolute and incremental indexing with I/O triggering
capability (MAPOS, MASPEED, MIDIST0, MIDIST1, MIDIST2,
MIDIST3, MISPEED0, MISPEED1, MISPEED2, and
MISPEED3) through either the serial port or the hardware
configurable inputs (IN1, IN2, IN3, IN1MODE, IN2MODE,
IN3MODE).
− Position homing with I/O triggering capability (MH, HOMESPD,
HOMESTATE, HOMETYPE) through either the serial port or
the configurable inputs (IN1, IN2, IN3, IN1MODE, IN2MODE,
IN3MODE).

− Electronic Gearing (Position Mode - OPMODE 4) featuring

pulse following or master encoder capability with resolution up
to 3 MHz through C8 connector (2.5 kHz through opto-isolators
in C3) (GEAR, GEARMODE, GEARI, GEARO, PEXT,
PEXTOFF, VEXT, XENCRES, XENCDIR). Homing capability
is provided.
− Dual-loop mode (DUALFB) capable of positioning from a load
feedback (C8 input, PEXTOFF, PEXT, VEXT, XENDIR) device
while controlling velocity and torque from the motor feedback
(C2 input).
− PID position loop tuning (GP, GPD, GPI, ) with feed-forward
acceleration gain input to both the velocity and current loops
(GPAFR, GPAFR2), and feed-forward velocity gain input to the
velocity loop (GPVFR).
− Software position limits (PLIM, PMAX, PMIN, PEMAX).
− Configurable integrator dynamics through travel range
(GPISATOUT, GPISATIN).
− Cumulative, revolution, and error position counters (PFB,
HWPOS, PRD, PE).
− Position indicators (INPOS, PEINPOS, PE, PEMAX, PFB,
PFBOFF).
9.1.4 PROFILE RAMPING CONTROL

− Electronic Braking (STOPMODE, ISTOP).
− Separate ACCEL and DECEL linear ramping control in velocity
and position mode (ACC, DEC, PROFMODE).
− S-curve ACCEL and DECEL ramping control (PROFSCRV,
PROFMODE) in the position mode (OPMODE=8).
− Controlled decelerating (DECSTOP, DISSPEED, DISTIME)
with acceleration feed-forward when the drive is left enabled
(STOP, HOLD, CWLIM, CCWLIM, LIMDIS) or becomes
disabled (K, S, ACKFAULT, DIS). This feature can be used in
conjunction with the Electronic Braking feature.
− Torque compensator for coulomb friction and weight counter-
balancing (IFRIC, IGRAV).
9.1.5 MOTOR CONTROLLABILITY

− Provides linear and rotary motor control (MOTORTYPE,
MPITCH, MENCRES) with automatic unit conversion.
− Configurable back EMF characteristics for effective current
loop controller design and command (MBEMF,
MBEMFCOMP).
− Danaher Motion’s patented Torque Angle control to maximize
motor output power (MTANGLC, MTANGLP, MVANGLF,
MVANGLH).
− Motor speed and current limits (MSPEED, MICONT, MIPEAK).

− Thermal protection control (MFOLD, MFOLDD, MFOLDDIS,

MFOLDR, MFOLDT) adaptable to any motor.
− Auto-configuration feature (ACONFIG, ACONFIGST, MFBDIR)
automatically configures the motor’s power and feedback
cables. It checks, warns, and corrects for incorrect wiring of
these cables.
− Configurable positive motion direction (DIR).
9.1.6 FEEDBACK DEVICES

Device zeroing mode that rotates the motor to an electrical null
point (ZERO, IZERO).
9.1.6.1 RESOLVERS
− Variety of motor and resolver pole combinations (MPOLES,
MRESPOLES).
− Resolver-zero offsetting (MPHASE).
− System accuracy better than 20 arc minutes (reduced when
resolver pole count is increased).
− Inter-LSB interpolation between least significant bits
(ILSBMODE) allows 18-bit velocity control and 16-bit
positioning capability.
− Automatic resolution configuring, based on application speed
requirements (RDRES, VMAX).
9.1.7 ENCODERS
− Maximum frequencies to 3 MHz before quad.
− Up to 10 million counts per motor electrical cycle (MENCRES).
− Configures automatically (ENCINIT, ENCINITST, ENCSTART,
IENCSTART).
− Index pulse offsetting capability (MENCOFF).
− Variety of encoder types (MENCTYPE):
1. Encoder with or without index.
2. Encoder-hall effects with or without index (MHINVA,
MHINVB, MHINVC, HALLS).
9.1.7.1 SINE ENCODERS

256x internal interpolation.
Up to 128x encoder equivalent output (SININTOUT).
Most standard encoder features mentioned above.

9.1.8 SYSTEM COMMUNICATION

Serial communications port (address setting through DIP switch on
top of drive).
− RS-232 single and up to 31-axis multi-drop addressing
(ADDR).
− RS-485 single and up to 31-axis multi-drop addressing
(ADDR).
− Data transmission (DUMP, GET, LIST, MLIST, GETMODE)
baud rates of 9600 or 19200.
− Configurable protocol (ECHO, PROMPT, ACKMODE,
GETMODE, MSG).
− Interface through Danaher Motion’s MOTIONLINK or a dumb
terminal.
Differential analog input command (ANIN).
− ±10 V at 14 bit resolution.
− ±10 V at 15 bit resolution below 4 V of input for slow speed
operation using the Dual Gain feature (ANDG - SE units only).
− Input signal filtering (ANLPFHZ).
− Flexible analog input scaling (VSCALE, ISCALE, ANOFF,
ANZERO, ANDB).
SERCOS interface communications port (SERCOS interface
versions only).
− 2 ms update rate.
− Complete set of manufacturer’s IDNs.
− MOTIONLINK communication through the serial port.
Encoder Equivalent Output (EEO) signal (C4 connector) eliminates
the need for an additional position feedback device. The maximum
frequency of this output is 3 MHz for standard encoders and 1.2
MHz for sine encoders.
− Resolver-based systems: developed through R/D hardware
circuitry for minimal phase lag, it provides a before quad
resolution of up to 16384 lines (65536 quad counts) per
revolution of the motor shaft (dependant on motor speed). This
signal resolution is configurable (ENCOUT). Index pulse can
be varied as much as one complete revolution (INDEXPOS).
− Encoder-based systems: actual encoder signals are exported
through this output (MENCRES) and can be scaled down by
multiples of two (ENCOUTO).
− Sine-encoder systems: developed through the interpolator
circuit (SININTOUT) and encoded to a quadrature signal. A
frequency limiter (MSINFRQ) is provided with fault protection.

9.1.9 MOTIONLINK SOFTWARE ENVIRONMENT

− Easy setup, commanding, and monitoring techniques.
− Contains an extensive database for many of Danaher Motion’s
motor series.
− A backup screen that provides automatic loading of system
parameters.
− Realtime metering of many system parameters.
− PC scope feature for profile recording and realtime motion
performance measuring.
− Optional terminal mode feature for keystroke commanding and
monitoring.
− Status screen indicating system operation and fault/error
checking.
− Extensive on-line help file (F1) designed to assist you in
MOTIONLINK’s intuitive nature.
− A set of limits folders allowing you to manipulate the position,
velocity, current, and filtering limits from one screen.
− An I/O screen for easy manipulation of the drive’s I/O,
thermostat options, encoder output, and hardware position
limits capabilities.
− A feedback device screen that provides realtime pictorial
positioning information. It also includes a resolver zeroing
routine and an encoder initialization folder.
− A tuning screen designed to allow you to adjust control loop
gains quickly while visibly watching the affects on performance.
− A control loops screen that provides direct manipulation of
velocity and position loop gain parameters.
9.1.10 MONITORING AND TROUBLESHOOTING TOOLS

− Performance recording (RECDONE, RECING, RECOFF,
RECORD, RECRDY, RECTRIG).
− System status checking (STAT, STATUS, STATUS2).
− Control loop monitoring:
1. Current/torque (I, IA, IC, ICMD, IMAX, ICONT, DICONT,
DIPEAK).
2. Speed (V, VCMD, VE).
3. Position (PCMD, PFB, PE, HALLS, HWPOS, INPOS,
PRD, PEXT, PEINPOS).
− Analog output (ANOUT) with 12-bit resolution and scaling
flexibility (PSCALE) that can be configured to monitor speed,
torque, current, power, velocity error, following error, and
position feedback (PFB). Should be used as a monitoring tool
only.

− Dual-state digital output (O1, O1MODE, O1RST, O1TRIG) that

toggles according to various absolute current, speed, and
position parameter settings. Also can be used to communicate
occurrences of fold-back, motor braking, and the status of the
Remote Enable hardware switch.
− Status Display (TESTLED) indicator that communicates
operational and fault characteristics.
− Realtime reading of the 10-position DIP switch (DIP, DIPEN).
− Software status switch indicator provided for configurable
inputs (IN1, IN2, IN3, IN1MODE, IN2MODE, IN3MODE).
9.1.11 FAULT AND SAFETY DETECTION

− General faults (ACKFAULT, STAT, STATUS).
− Configurable under-volt protection (UVMODE, UVTIME,
UVRECOVER).
− Speed and current protection (VOSPD, VLIM, ACC, DEC,
ILIM, ILIM2).
− Fatal and non-fatal error coding with text explanation to the
host (ERR, FLTHIST, FLTCLR). A run-time counter (TRUN)
that records the time the error occurred is also provided.
− Configurable motor thermal protection that accepts various
thermostat types (THERM, THERMODE, THERMTYPE,
THERMTIME).
− Configurable drive thermal protection through the fold-back
feature (FOLD, FOLDMODE). It sets the maximum time limit
the drive can provide peak current (3:1 for Cx) to the motor.
− Configurable motor thermal protection through the motor fold-
back feature (MFOLD, MFOLDD, MFOLDDIS, MFOLDR,
MFOLDT). It sets the maximum time limit the drive can provide
continuous current to the motor.
− Hardware position limit switch detection (CCWLIM, CWLIM,
LIMDIS, IN1, IN2, IN3, IN1MODE, IN2MODE, IN3MODE).
− Configurable software position limits (PLIM, PMAX, PMIN,
PEMAX).
− Configurable fault relay output (RELAY, RELAYMODE,
DISTIME, IN1MODE, IN2MODE, IN3MODE).
− Active disable feature (ACKFAULT) that allows you to
determine how the system should react at the occurrence of a
fault. The system can immediately disable, where the motor
will coast to a stop, or it can be programmed to a controlled
decelerated stop (DECSTOP, DISSPEED, DISTIME,
STOPMODE, ISTOP).
− Active enable indicator through the Status Display decimal
(ACTIVE, DRIVEOK, SWEN, READY, REMOTE, DIPEN).

9.1.12 GENERAL
− Many enabling and disabling features (K, S, STOP, REMOTE,
EN, DIS).
− Flash firmware memory for easy field upgrade installation.
− Danaher Motion’s patented Torque Angle Control for buried
magnet motor designs (MTANGLC, MTANGLP, MTANGLF,
MTANGLH - defined as speed and torque optimization through
commutation angle advancing of the drive’s output current
waveform with respect to the motor's back EMF waveform.
− Firmware and serial number information (VER, SERIALNO,
MOTOR) via terminal.

Danaher Motion Kollmorgen 06/04 Troubleshooting
10 TROUBLESHOOTING
Technical papers and publications about the SERVOSTAR and its
associated applications complete the information package
necessary for you to become well versed with the product. Danaher
Motion’s engineering and technical resource staffs have prepared
these notes. The PSP CD-ROM contains technical content stored
in an electronic .PDF format. You must have Adobe’s Acrobat
Reader (also available on the CD-ROM) installed on their computer
to view and print these documents. This package is available on the
CD-ROM. The most recent versions of all the material contained in
this PSP (manual and CD-ROM) can be downloaded from Danaher
Motion’s website (www.danahermotion.com).
10.1 Troubleshooting Tools

The SERVOSTAR’s MOTIONLINK package comes with a
comprehensive monitoring and troubleshooting help set. For
troubleshooting the drive, it provides a status screen (click on
Status in the upper right-hand corner of Main MOTIONLINK
screen). The Status screen allows you to check the drive enable
switches, the status display LED, fault status with complete error
history, and mode settings for several of the drive’s protection
features. If using the terminal mode, you can simply check the
contents stored in STATUS, FLTHIST, and ERR.
An additional help provided by MOTIONLINK is the I/O screen
(click on I/O button on the side of the Main MOTIONLINK screen).
The I/O screen gives you the ability to check the status of the
hardware position limit switches, the motor thermostat, and the
encoder equivalent output. It also allows you to set up the I/O on
the C3 connector for a variety of troubleshooting and monitoring
approaches.
For monitoring system performance, MOTIONLINK comes with a
variety of monitoring tools. The customer can monitor a variety of
variables from the Monitor screen (click Monitor button at the top of
the Main MOTIONLINK screen) to compare up to three variables
against themselves at one time. The Tune and Record screen
allows you to evaluate the system’s actual performance against a
predefined command profile. Also from this screen, adjusting the
gains until optimum following is achieved can vary the performance.

Troubleshooting 06/04 Danaher Motion Kollmorgen
10.2 Error Codes

In most cases, the SERVOSTAR communicates error codes with a
text message via the serial port to the host. Some error codes are
also transmitted to the status display. The same message is saved
in the EEPROM under an error history log (FLTHIST, ERR) so that
nothing is lost when power is removed. Not all errors reflect a
message back to the host. In these cases, the no-message errors
communicate to the Status Display only.
− The response of the SERVOSTAR to an error depends on the
error's severity. There are three levels of severity:
1. Warnings, simply called errors, are not considered faults
and do not disable operation
2. Non-fatal errors, or simply faults, that disable the drive and
indicate a fault status
3. Fatal errors, or fatal faults, that disable almost all drive
functions (including communications)
The drive is automatically disabled at the occurrence

of a fault. Executing a drive disable command (DIS or
K) followed by EN, or toggling the Remote Enable line
(REMOTE) resets the fault latch, and if the fault
condition is no longer present, re-enables the system.
NOTE
10.2.1 FATAL FAULT ERROR CODES

Display Fault Message Possible Cause Err #
overload, fan malfunction, power stage
t Power stage OverTemp 1
failure
o OverVoltage excessive decel rate* 2
P OverCurrent power stage surge current* 3
Feedback signal through C8 not correctly
r0 External feedback fault 4.0
detected
r1 Resolver line break break in resolver feedback detected 4.1
fault in resolver-to-digital converted
r2 RDC error 4.2
detected
sine encoder card has not initialized
r3 Sine Encoder init fail 4.3
properly
r4 A/B line break break in encoder A/B input lines detected 4.4
r5 Index line break break in encoder index line 4.5
r6 Illegal halls illegal hall combination detected 4.6
r7 C/D line break break in sine encoder C/D line detected 4.7
r8 A/B out of range sine encoder A/B level out of range 4.8
r9 Burst pulse overflow sine encoder fault 4.9
Endat Communication Serial communication to the Endat Encoder
r10
Fault failed
u Under voltage bus voltage is too low 5
H Motor over temperature motor overload caused overheating 6
A1 Positive analog supply fail Failure in +12V supply (regulated) 7.1
A2 Negative analog supply fail Failure in -12V supply (regulated) 7.2
J OverSpeed velocity ≥ VOSPD 8
J1 OverSpeed Velocity ≥ 1.8 x VLIM 8.1
E EEPROM failure Faulty EEPROM 9
e EEPROM checksum fail EEPROM checksum invalid on power up* 10
F Foldback System in FoldBack mode 12

Display Fault Message Possible Cause Err #
d5 Positive over travel fault PFB exceeded PMAX with PLIM=1 14.1
d6 Negative over travel fault PFB exceeded PMIN with PLIM=1 14.2
d1 Numeric position deviation Internal fault 15.1
Excessive position
d2 PE > PEMAX 15.2
deviation
c Communication interface A communications fault has occurred 16
*These faults can only be cleared by cycling power
10.2.2 NON-FATAL ERROR CODES

Error Message Possible Cause Err #
No Error no error was recorded 0
Unknown Command Undefined command 20
Unknown Variable undefined variable name 21
Checksum error error on comm. message checksum (ACKMODE 2) 22
drive needs to be inactive for the requested
Drive Active 23
command or variable
drive needs to be active for the requested command
Drive Inactive 24
or variable
Value out of range variable value out of range 25
Negative Number variable must be ≥ 0 26
Not in proper Opmode not in correct Opmode for specified command 27
Syntax Error communication message syntax error 28
Tune Failed auto tuning failed 33
Bad Bandwidth AutoTuning BW is out of range 34
Bad Stability bad stability 35
Not programmable variable is read-only 36
Current loop design failed CONFIG failed due to current loop design failure 37.01
MENCRES out of range CONFIG failed due to MENCRES 37.02
MENCOFF out of range CONFIG failed due to MENCOFF 37.03
MSPEED out of range CONFIG failed due to MSPEED 37.04
MBEMF out of range CONFIG failed due to MBEMF 37.05
MJ out of range CONFIG failed due to MJ 37.06
ACC out of range CONFIG failed due to ACC 37.07
DEC out of range CONFIG failed due to DEC 37.08
DECSTOP out of range CONFIG failed due to DECSTOP 37.09
VLIM out of range CONFIG failed due to VLIM 37.10
VOSPD out of range CONFIG failed due to VOSPD 37.11
VSCALE out of range CONFIG failed due to VSCALE 37.12
O1TRIG out of range CONFIG failed due to O1TRIG 37.13
O1RST out of range CONFIG failed due to O1RST 37.14
DISSPEED out of range CONFIG failed due to DISSPEED 37.15
MENCTYPE out of range CONFIG failed due to MENCTYPE 37.16
Communication error Error at physical comm. layer 38
The REFRESH command was given with
Not in proper COMPMODE 39
COMPMODE ≠ 3
D, H, R parameters for COMP-MODE 3 do not have
EXT velocity param warning 40
the proper relationship to each other.
The velocity loop can’t be con-figured with given
Vel loop design failed 41
parameters
Invalid EEPROM The EEPROM test failed 42
The requested command cannot be executed
Recording active 43
because it conflicts with a recording in progress
Rec data not available No data are available for the GET command 44
Data cannot be loaded because the EEPROM is
EEPROM is empty 45
empty
Argument must be binary Variable argument must be a power of 2 46
The requested function cannot be executed during
Burnin is active Burnin 47
(a factory function)
Burnin (factory function) cannot be stopped if it is not
Burnin is not active 48
active

Error Message Possible Cause Err #
The requested value for VLIM conflicts with
Conflicts with ENCOUT 49
ENCOUT.
The requested value for ENCOUT conflicts with
Conflicts with VLIM 50
VLIM.
The requested variable value is not available; refer
Not available 51
to the description of the variable to determine why.
Drive is in Hold mode Motion was requested with the drive in Hold mode 52
Drive is in Hold mode due to limit switch being
Limit Switch Hold 53
tripped
Requested motion is in direction of tripped limit
Command Into Limit 54
switch
Drive is in Zero Mode Motion requested while in Zero mode 55
Tune cmd cannot be executed because motor is
Motor is Jogging 56
jogging
Argument not divisible by 20 Argument must be a multiple of 20 to be accepted 57
A command cannot be executed because it has
Encoder Initialization Process
been requested while the encoder initialization 58
Active
process is active
Tune failed-no rotation Tune cmd failed because motor could not rotate 60
62,66
Tune failed-current sat Tune cmd failed because the current loop saturated
70,74
Tune cmd failed because the vel loop could not be 63,67
Tune failed-no vel design
designed 71,75
Tune cmd failed because drive was disabled while
Disable During Tune 76
tuning
Tune cmd failed because drive entered Hold mode
Hold During Tune 77
while tuning
Low Velocity Limits Tune cmd failed because VLIM is too low 78
Tune cmd requires a lower bandwidth in order to
Use Lower Bandwidth 79
execute
Command cannot be accepted because dual
Drive in Dual Feedback mode 80
feedback is active
Command cannot be accepted because drive is in
Drive is in Gear mode 81
gear mode
Selected INxMODE function is already assigned to
Functionality is occupied 82
another INxMODE
Selected GEARMODE requires A/B inputs to be
Warning: A/B Line not routed 83
routed using INxMODE 5 and 6.
Limit switches must be routed using INxMODE 1 and
Warning: Limit sw not routed 84
2.
The last ordered move command has not been
Move is pending 85
completed yet.
Incorrect password The password entered was incorrect 90
The command or variable requested is password
Password protected 91
protected and intended for factory use only
Capture during homing A position capture occurred during homing 92
Homing during capture A homing request was made during position capture 93
The requested command can’t be processed due to
Capture process not done 94
pos capture not being complete
The requested command can’t be processed due to
Capture process not active 95
pos capture not being active
Capture process not enabled Position capture cannot be executed 96
ENCSTART while ACONFIG 97
SERCOSinterface test failure 999

10.2.3 NO MESSAGE FAULTS

Non- Flashing Steady
Display Fault Description Fatal
Fatal Display Display
≡ Watchdog (DSP) X X
≡ Watchdog (HPC) X X
-1 No Compensation X X
-2 Invalid Velocity Control X X
-3 Encoder not Initialized on attempt to X X
enable
-4 Encoder Initialization failure X X
-5 AutoConfig failure X X
L1 Hardware CW limit switch open X X
L2 Hardware CCW limit switch open X X
L3 Hardware CW and CCW limit switches X X
open
L4 Software CW limit switch is tripped X X
(PFB>PMAX & PLIM=2)
L5 Software CCW limit switch is tripped X X
(PFB<PMIN & PLIM=2)
A3 Positive and negative analog supply fail X X
I RAM failure (during init) X X
c EPROM checksum (during init) X X
E101 Altera load failure (during init) X
E102 Altera DPRAM failure (during init) X
E103 DSP load fail (during init) X
E104 DSP alive failure (during init) X
8 Test LED X
B Indexed position with zero velocity X
10.3 Fault Monitoring System

The SERVOSTAR’s microprocessor is constantly monitoring the
status of many different components. In general, the philosophy of
the SERVOSTAR is to latch all fault conditions so you can readily
determine the source of the problem. When a fault is detected, it is
logged in the internal error log, indicated in the Status Display,
enunciated over the serial port, and in most conditions causes a
drive disable. Many faults can be reset by toggling the hardware
remote enable (REMOTE input).
The following provides a list of some of the more frequent faults the
drive may detect in the unit hardware and operating system.
Motor OverTemperature
The Motor’s External Thermostat input is monitored for an open
circuit condition. You can define (using THERMODE) what happens
under this fault condition. The worst case event is a power stage
disable when an ‘H’ appears in the status display, and the fault
relay contacts (RELAY) are open.

Hardware Position Limit Inputs

The IN1, IN2, IN3 inputs are constantly monitored. If INxMODE set
these inputs for CW/CCW hardware position limits, they are
monitored for an open-circuit condition. Although not necessarily an
error condition, motor operation can be affected by these inputs.
The SERVOSTAR can ignore the hardware position limits if you set
LIMDIS = 1. The worst case event is that further motion in the given
direction is not allowed with an ‘L’ illuminated in the status display.
If both CW and CCW position limit inputs have detected an open-
circuit condition, the SERVOSTAR enters into Hold position state
(HOLD = 1).
Drive OverTemperature
The internal heatsink temperature is monitored for an unsafe
condition. This condition causes a ‘t’ to be displayed and disables
the drive. The drive will eventually cool enough to allow reset of this
condition.
RMS OverCurrent (FoldBack)
The FoldBack detection system can ‘clamp’ the available output
current. This is not a true fault condition, but may cause undesired
performance, due to the command current being limited below what
is required to achieve the desired performance. This condition is
indicated with a flashing ‘F’ in the status display and can be
detected by monitoring the FOLD switch variable.
Bus OverVoltage
An over-voltage condition shuts down the drive and displays a
lower-case ‘o’ in the status display. This fault will occur mostly
during regen operation where the bus is raised to higher values
than that produced by the power supply.
Bus Under-Voltage
An under-voltage condition shuts down the drive and displays an ‘u’
in the status display. This fault normally occurs when the incoming
line voltage drops out or a fault occurs in the power supply.
PowerStage Fault (over-current)
Hardware circuitry monitors load short-circuit, transistor failure, and
instantaneous over-current. In general, toggling the Remote Enable
cannot reset a power stage fault. Power must be cycled. A flashing
‘P’ in the status display indicates this condition.
Feedback Loss
Hardware is used to detect a wire-break condition in encoder based
systems or the presence of the Sine and Cosine resolver feedback
signals in resolver based systems. The SERVOSTAR disables and
displays an ‘r’ in the status display when either of these signals are
not present.
Low-voltage power supply faults
Out of tolerance values on the ± 12 VDC analog supplies cause an
A to be displayed and disables the drive.

Over-Speed fault
Software continuously monitors the actual (feedback) speed. If the
motor speed exceeds the VOSPD limit, a J is displayed and the
drive is disabled. This normally occurs when there is an improperly
tuned system and the load overshoots its commanded speed.
No compensator
In case the SERVOSTAR cannot design a compensator, such as
after a RSTVAR, CLREEPROM, or any change in the motor or
drive parameters, a flashing minus sign (-) is displayed and causes
the drive to disable. This display normally indicates that the drive
does not have a compensation file loaded.
Memory reliability
During the initialization process upon power up, the run time,
variables memory (RAM - Random Access Memory), and the
program memory (EPROM - Electrically Programmable Read Only
Memory) are tested.
If a RAM fault is detected
An ‘I’ is displayed and the drive is halted. If an EPROM fault is
detected, a ‘c’ is displayed and the drive is halted.
Non-volatile memory (EEPROM)
Non-volatile memory (EEPROM)is also checked for integrity upon
power-up. Any discrepancy in this data is noted with an ‘e’ in the
status display. After power-up is successfully completed, any
subsequent fault in the operation of the EEPROM is noted with an
‘E’ in the status display.
WatchDogs
In addition, the SERVOSTAR incorporates a watchdog system to
maintain software operation integrity. Failure of the watchdog
mechanism will display three bars on the status display and cause
the drive to halt. This normally indicates serious problems. Please
contact the factory for support.

10.4 Firmware Upgrades

10.4.1 UPGRADE PROCEDURES
The field upgrade of firmware in CD Series product requires an
application program called Ignite.exe that is provided at
www.danahermotion.com. The following steps are provided for the
use of this software utility.
Setup: The power must be on to the servo drive. The servo drive
must be disabled. An RS232 Serial port connection between the
computer and the drive must be made. Ignite.exe and the firmware
file (version.emb) must be accessible by the computer. It is
recommended that the communication rate in the servo drive and
Ignite.exe be set to 19.2 k Baud for a more rapid download of
firmware.
Launching Ignite.exe brings up the following screen on your
computer. Press the Advanced button to select the firmware file
that you want to download to the servo drive.

Only one firmware file should show up in the selection window. Use
the Add button and Delete button to obtain the correct file. Press
OK when you are satisfied.
The first window reappears to allow you to select the appropriate

communication port (Com Port) and communication rate (Baud
Rate). Once you have made your selections, press the Start button.

The drive will display an E in the display acknowledging that it has

been put into the firmware download mode. When the software
download is complete, Ignite.exe will signal “Download successful”.
The servo drive power must be cycled (turned off then back on) in
order to return the servo drive to its normal operating mode.
You should then use MOTIONLINK to do one of the following:

a.) Load the motor compensation file and issue a RSTVAR (reset
variables) command
OR
b.) Load a user file that has been saved to your computer
(xxxx.SSV)
Advanced options:
1) Use a specific address – can be selected when using RS485
multidrop to direct the firmware to a specific drive on the
communication multidrop
2) Skip drive seeking – select this options if your drive is already
in firmware doanload mode or simply to avoid the scan process
by defaulting to the specified communication address

Danaher Motion Kollmorgen 06/04 Appendix A
APPENDIX A
A.1 Motor Pinouts
The SERVOSTAR CD product family can be mated with a variety
of motors. Cable sets (motor and feedback) can be purchased
directly from Danaher Motion; which gives you a complete plug-n-
play system. However, you may find it necessary to manufacture
your own cable sets. This Appendix provides pinout information
between the drive’s power and feedback connections and the motor
receptacles for most of Danaher Motion’s motor products.
SERVOSTAR GOLDLINE B, M, EB & XT DDR
B/M/EB XT WIRE Color Wire Color

DRIVE Motor
Motor Motor (Winding to (Winding to
CONNECTIONS Receptacle
Receptacle Receptacle Receptacle) Receptacle)
MA Pin A 3 Brown Pin 3 Black
MB Pin B 4 Red Pin 4 Red
MC Pin C 1 White Pin 1 White
GND Pin D 2 Green/Yel. Pin 2 Green
RBHR/
SERVOSTAR SILVERLINE
RBE(H)
DRIVE Wire Color

Motor Receptacle Wire Color
CONNECTIONS (Winding to Receptacle)
MA Pin 1 Red Red
MB Pin 2 White White
MC Pin 6 Black Black
GND Pin 7 Green
SERVOSTAR GOLDLINE B, M, EB, XT

Wire Color
XT XT
C2 B/M/EB (from resolver to
50X & 70X 30X
motor receptacle)
Pin 1 Pin A Pin A Pin 3 Black
Pin 2 Pin B Pin B Pin 7 Red
Pin 3 (shield)
Pin 4 Pin D Pin D Pin 8 Yellow
Pin 5 Pin C Pin C Pin 4 Blue
Pin 6 (Shield )
Pin 14 (Shield )
Pin 15 Pin F Pin F Pin 5 Yellow/White
Pin 16 Pin E Pin E Pin 9 Red/White
Pin 13 Pin T Pin R Pin 2 Yellow
Pin 25 Pin U Pin S Pin 6 Yellow
Pin 12 (Shield )

Appendix A 06/04 Danaher Motion Kollmorgen
SERVOSTAR DDR RBHR

Wire Color
Resolver
C2 (from resolver to Wire Color
Connector
motor receptacle)
Pin 1 Pin 3 Black Yellow
Pin 2 Pin 7 Red Blue
Pin 3 (shield)
Pin 4 Pin 8 Yellow Red
Pin 5 Pin 4 Blue Black
Pin 6 (Shield )
Pin 14 (Shield )
Pin 15 Pin 5 Yellow/White Red / White
Pin 16 Pin 9 Red/White Yellow / White
Pin 13 Pin 2 Blue
Pin 25 Pin 6 Red
Pin 12 (Shield )
SERVOSTAR GOLDLINE B, M, EB & XT

Wire Color
C2 Encoder Receptacle
(at Motor Receptacle)
B, M, EB Series XT Series XT Series
MS threaded MS Threaded Euro Style
Pin 1 Pin A Pin A Pin 1 Blue
Pin 2 Pin M Pin M Pin 2 Blue / Black
Pin 3 (shield)
Pin 4 Pin B Pin B Pin 3 Green
Pin 5 Pin C Pin C Pin 4 Green / Black
Pin 6 (Shield )
Pin 7 & 8 Pin S Pin S Pin 7 Red
Pin 9 Pin F Pin F Pin 17 Brown
Pin 10 Pin H Pin H Pin 16 Gray
Pin 11 Pin K Pin K Pin 15 White
Pin 12 (Shield )
Pin 13 Pin T Pin T Pin 8 Yellow
Pin 14 (Shield )
Pin 15 Pin D Pin D Pin 5 Violet
Pin 16 Pin E Pin E Pin 6 Violet / Black
Pin 18,19 & 20 Pin R Pin R Pin 10 Black
Pin 22 Pin G ( see note 1 ) ( see note 1 ) ( see note 1 )
Pin 23 Pin J ( see note 1 ) ( see note 1 ) ( see note 1 )
Pin 24 Pin L ( see note 1 ) ( see note 1 ) ( see note 1 )
Pin 25 Pin U Pin U Pin 9 Yellow
NOTE 1. Must be shorted to C 2 pin 18 for proper operation

Danaher Motion Kollmorgen 06/04 Appendix A
SERVOSTAR SILVERLINE RBE(H)

0802 Encoder Encoder
C2 0802 Wire Color
Receptacle Receptacle
Pin 1 Pin 3 Blue Pin 6
Pin 2 Pin 6 Blue / Black Pin 5
Pin 3 (shield)
Pin 4 Pin 4 Green Pin 8
Pin 5 Pin 7 Green / Black pin 7
Pin 6 (Shield )
Pin 7 & 8 Pin 10 Red Pin 2
Pin 9 Pin 12 Brown
Pin 10 Pin 13 Gray
Pin 11 Pin 14 White
Pin 12 (Shield )
Pin 13 Pin 1 Yellow
Pin 14 (Shield )
Pin 15 Pin 5 Violet Pin 10
Pin 16 Pin 8 Violet / Black Pin 9
Pin 18,19 & 20 Pin 9 Black Pin 3
Pin 22 ( see note 1 ) ( see note 1 ) ( see note 1 )
Pin 25 Pin 2 Yellow
NOTE 1. Must be shorted to C 2 pin 18 for proper operation

Appendix A 06/04 Danaher Motion Kollmorgen
A.2 System Connection Diagram

Danaher Motion Kollmorgen 06/04 Appendix B
APPENDIX B
B.1 Digital Incremental Encoder Types
The SERVOSTAR products include models designed for use with
incremental digital encoders. Encoders are available in different
configurations from a variety of manufacturers using different
nomenclature and conventions, making this topic somewhat
confusing. Encoders can be as simple as having only A and B
output channels or as complex as 6 channels of outputs. The
SERVOSTAR supports many of these variants using the variable,
MENCTYPE. The variable is set according to the features of the
encoder. This document explains the different applications of the
various MENCTYPEs. A basic understanding of encoders is
valuable for this discussion.
B.1.1 ENCODER BASICS: A REVIEW

Encoders used with the SERVOSTAR provide incremental motor
position information via two channels, referred to as the A Channel
and B Channel. These channels output pulses for a unit of shaft
motion. These pulses are typically generated within the encoder,
using an optical disk that is directly connected to the motor shaft.
The disk has etchings that either transmit or block light passing
through the disk. An optical transmitter and receiver are on either
side of the disk. The rotation of the disc (and motor shaft) interrupts
light transmission from source to receiver, creating the pulses. The
interruptions on the disk are called lines and result in the encoder
ratings of lines-per-revolution (LPR) or pulses-per-revolution (PPR).
The two channels provide the same information (pulses-per-unit of
motion), but have a phase shift of 90º between each other as
shown in the figure below.

Appendix B 06/04 Danaher Motion Kollmorgen
The 90º electrical phase shift between the two channels is referred
to as "quadrature-encoded." The encoder output appears as a
frequency, but the pulse rate is dependent on the motor's rotational
velocity, not time. Since the two channels are phase-shifted by 90º,
there are actually four states available per electrical cycle of these
signals. The SERVOSTAR is able to receive four counts for
position feedback for one line of motion of the encoder. The actual
decode of the four position counts-per-line of the encoder is called
"quadrature decode."
Additionally, since the encoder signals A and B are phase shifted
by 90º, it is easy to design electronics that recognize whether A
came before B or B came before A, thus supplying directional
information. Encoders are often provided with an additional channel
called a "Marker" channel, Zero Pulse, or an "Index" channel -
different names for the same function. This channel outputs one
pulse per revolution and is typically an extremely narrow pulse
equating to roughly ¼ of the width of an A or B channel pulse but
can be wider. This is a reference position marker used for homing
(absolute position reference) and commutation alignment.
One challenge when using encoders is that they are incremental
rather than absolute devices. When using an absolute device (such
as a resolver) to determine the motor shaft position within the
rotation, the transmitted code is unambiguous. In other words, at
power-up, the system knows the position of the motor shaft.
Incremental encoders only detects how far the motor shaft has
moved from its original position. This presents a problem with
three-phase brushless motors in terms of commutation alignment.
Generally, it is extremely important to establish the appropriate
commutation angle within the controller. (Commutation refers to the
alignment of the electromagnetic field armature winding to the
permanent magnet fields to create optimal torque.)
For this reason, encoders or motors are often provided with
additional channels sometimes called "commutation tracks" or "Hall
emulation tracks" which provide 1-part-in-6 absolute position
information as shown in the following figure.

The hall channels can be synthesized in the encoder or can be

discrete devices integrated in the motor windings. Commutation
tracks (hall channels) provide three digital channels that represent
alignment to the A-phase, B-phase, and C-phase back EMF of the
motor. An encoder with Hall channels must have the correct output
for the given pole count of the motor as the Hall signals are
referencing the motor's BEMF waveform.
Some systems use only hall channels for motor feedback
data. The channels provide enough information to
commutate a motor in an ON and OFF (trapezoidal) format
but do not provide enough information to properly
commutate a motor using sinusoidal control. Further, the
coarse data is insufficient to control velocity below a few
hundred rpm. The SERVOSTAR product is a high-
performance controller and does not support hall-only
NOTE operation.
Since encoders are incremental devices, a loss or gain of a pulse

creates system errors. Electrical noise is the single biggest factor in
miss-counts. Transmitting the signals differentially provides the
largest margin of noise rejection and the best signal fidelity. The
SERVOSTAR is designed to receive only differential signals. Some
"less expensive" encoders provide TTL or "Open Collector" signals.
These are not compatible with the SERVOSTAR.

B.1.2 SERVOSTAR ENCODER TYPES

The idea of obtaining velocity MENCTYPE 0
or position information from
the series of pulses
generated from the encoder
is not difficult to understand. Read Hall Codes
Permanent magnet Establish
brushless DC servo motors Commutation
Angle as though in
require commutation. As the middle
stated earlier, commutation
is simply the positioning of
the electromagnetic fields in
alignment with the
No Marker Channel Yes
permanent magnet fields Occur?
such that optimal torque is
produced. This requires that
the motor shaft position be
known at all times. The use
of incremental encoders
requires some form of
Hall Code Change?
initialization to determine this
motor shaft position at power
up. It is this commutation
initialization process that can
lead to confusion.
Adjust
Commutation
Since the SERVOSTAR Angle
supports operation with
many encoder types, it must
be told which signals to
expect to see and which No
Marker Channel
initialization algorithm to Occur?
perform. This is the purpose
of the MENCTYPE variable.
Yes
The following section
explains the MENCTYPE
Establish new
variable and its setting for Commutation using
each encoder type. The MENCOFF
figure on the right shows the
initialization flow chart for the
various MENCTYPEs. End

MENCTYPES 3 & 4
MENCTYPES 1 & 2
Drive puts IENCSTART

current through 2 phases
Perform MENCTYPE 3 & 4
algorithm and waits for motor to
stop
Position is read by drive

No
Marker Channel
Occur?
Drive puts current through

other phase. Wait for stop.
Yes
Establish new
Commutation using
MENCOFF
Drive establishes
commutation angle
End
End
B.1.2.1 MENCTYPE 0
Incremental with A/B/I and Hall Channels
MENCTYPE 0 is the most robust encoder system. The drive
expects the signals as feedback from the motor. The hall channels
is synthesized either in the encoder or discrete devices (Hall
sensors) integrated in the motor windings. On power-up, the hall
effect channels are read and a code is sent to the microprocessor
to give it a coarse position for the motor. This position is accurate to
within ±30 electrical degrees of the optimal commutation angle. The
SERVOSTAR assumes the actual motor position is half-way
between the hall code settings for a maximum commutation error of
±30 electrical degrees. Even with this amount of error, the motor is
capable of producing torque with 86% efficiency. As the motor
rotates, the first hall boundaries quickly traverse, providing the
SERVOSTAR with information to better establish commutation
angle. The SERVOSTAR corrects the commutation angle after it
sees the marker pulse, according to MENCOFF.

B.1.2.2 MENCTYPE 1
Encoders with A/B/I channels
Some systems do not have hall channels, so this mode tells the
SERVOSTAR not to expect them. The initialization process occurs
in two steps. The first step is the 'wake-and-shake initialization
process (see MENCTYPE 3 and MENCTYPE 4 for "wake and
shake" details) which gets the commutation alignment initialized
after power up. The second step occurs when the index pulse is
seen. Then, the SERVOSTAR aligns the commutation angle
according to the setting of MENCOFF. MENCTYPE 1 initialization
begins only when commanded through the serial port by using
ENCSTART.
The 'wake and shake' initialization process is not
required if the marker location can be traversed
without requiring the SERVOSTAR to move the motor
to traverse the marker.
NOTE
B.1.2.3 MENCTYPE 2
Encoders with A/B/I channels
Some systems do not have hall channels, so this mode tells the
SERVOSTAR not to expect them. The initialization process occurs
in two steps. The first step is the 'wake-and-shake initialization
process (see MENCTYPE 3 and MENCTYPE 4 for "wake and
shake" details) which gets the commutation alignment initialized
after power up. The second step occurs when the index pulse is
seen. The SERVOSTAR aligns the commutation angle according to
the setting of MENCOFF. MENCTYPE 2 is initialized using
ENCSTART or performed automatically upon power-up when the
drive is enabled.
The 'wake and shake' initialization process is not
required if the marker location can be traversed
without requiring the SERVOSTAR to move the motor
to traverse the marker.
NOTE
B.1.2.4 MENCTYPE 3
Encoders with A and B channels only
The simplest of encoders provide only an A and B Channel.
MENCTYPE 3 configures the SERVOSTAR for these signals.
These encoders provide no power-up information about where the
motor is positioned, so this information is obtained through a
special initialization process known as 'wake and shake'. When
using MENCTYPE 3, initialization is required but it is triggered by
ENCSTART.

During the initialization process, "wake and shake," the

SERVOSTAR puts current through two phases of the motor
causing the motor shaft to rotate into a "torque detent." The
magnets simply align the motor shaft to a position the
SERVOSTAR understands. The motor is then rotated to the next
pole position by energizing the windings in a slightly different
manner. The SERVOSTAR then has enough information to
establish an appropriate commutation angle using the number of
motor poles (MPOLES) and the number of counts for the encoder
(MENCRES).
This method of initialization has the advantage of allowing an
extremely cost-effective feedback device. However, the
requirement to pull the motor into these torque detents is subject to
outside influences (such as friction) and can prevent the motor
motion from occurring very effectively or even at all! Additionally,
large inertia loads can overshoot and oscillate during this pull-in
position, giving the microprocessor false readings. These
MENCTYPEs are best for systems with specific criteria
requirements such as low friction, low cost, and low inertial loads.
The amount of electrical current used in this initialization mode is
adjustable using IENCSTART and may need to be adjusted to
optimize performance for large inertial loads.
B.1.2.5 MENCTYPE 4
Encoders with A and B channels only
The simplest of encoders provide only an A and B Channel.
MENCTYPE 4 configures the SERVOSTAR for these signals.
These encoders provide no power-up information about where the
motor is positioned, so this information is obtained through a
special initialization process known as 'wake and shake'. When
using MENCTYPE 4, the process for initialization is automatically
triggered on power-up when the drive is enabled or by using
ENCSTART.
During the initialization process, "wake and shake," the
SERVOSTAR puts current through two phases of the motor
causing the motor shaft to rotate into a "torque detent." The
magnets simply align the motor shaft to a position the
SERVOSTAR understands. The motor is then rotated to the next
pole position by energizing the windings in a slightly different
manner. The SERVOSTAR then has enough information to
establish an appropriate commutation angle using the number of
motor poles (MPOLES) and the number of counts for the encoder
(MENCRES).

This method of initialization has the advantage of allowing an

extremely cost-effective feedback device. However, the
requirement to pull the motor into these torque detents is subject to
outside influences (such as friction) and can prevent the motor
motion from occurring very effectively or even at all! Additionally,
large inertia loads can overshoot and oscillate during this pull-in
position, giving the microprocessor false readings. These
MENCTYPEs are best for systems with specific criteria
requirements such as low friction, low cost, and low inertial loads.
The amount of electrical current used in this initialization mode is
adjustable using IENCSTART and may need to be adjusted to
optimize performance for large inertial loads.
B.1.2.6 MENCTYPE 5
Not supported
B.1.2.7 MENCTYPE 6
Incremental with A/B and Hall Channels
MENCTYPE 6 supports encoders as described in MENCTYPE 0,
but lacking the marker or index channel. This device is selected
using MENCTYPE 6 and follows the same process used in
MENCTYPE 0 with the exception of the final search for the marker
pulse. The system establishes the commutation angle based on the
Hall effect edge. MENCTYPE 6 is most commonly used with linear
motors.
B.1.3 COMMUTATION ACCURACY

The accuracy of the commutation alignment within the drive affects
the overall system efficiency. Misalignment also causes greater
torque ripple. As a general estimator, the following equation holds:
Kt effective = Kt Rated * Cosine (Alignment Error)
When using encoders, inaccuracy of commutation alignment can
occur from multiple sources. The accuracy of the hall channel
devices, if provided from an encoder using an optical disc, are
typically accurate to 5º or better electrically. When they are integral
to the motor, they may have an error of up to 15º. Using the above
equation, a 15º error still provides more than 96% of the motor's
torque.
The accuracy of the 'wake and shake' algorithms used in
MENCTYPE 1, MENCTYPE 2, MENCTYPE 3, and MENCTYPE 4
are subject to many outside influences, such as friction and inertia.
These algorithms are not robust and are subject to varying amounts
of error.
Incorrect commutation alignment also causes differences in
efficiency according to direction. In an exaggerated example, a
misaligned commutation angle may allow a 1500 rpm motor to go
2000 rpm in one direction and only 1000 rpm in the other.

B.1.4 PHYSICAL ENCODER ALIGNMENT

The SERVOSTAR provides a number of features (variables) to
adjust the encoder signal alignment through the software. These
features can be very useful, but you must be careful. If the
alignment of the encoder to the motor is left to chance, swapping
out the motor or encoder requires that these variables be
recalibrated for the new alignment. Is this acceptable in the given
application? You may not be certain that the knowledge to do so
will remain in the future. A better method is to align the encoder on
the motor. This makes swap-out a simpler process.
MENCTYPE 0 (A/B/I and Halls) has hall channels aligned to the
motors back EMF. This is accomplished by rotating the motor via
an external source, monitoring the signals from the hall effect
channels while monitoring the voltage generated by the motor and
rotating the encoder housing until the waveforms overlap. The
encoder mounting screws are then secured. This aligns the hall
channels and the marker channel must then be aligned using
MENCOFF. Use caution as motors may generate lethal voltages
when rotating.
MENCTYPE 1 and MENCTYPE 2 (A/B/I without Halls) require the
marker to be aligned to the motor's BEMF waveform. Danaher
Motion has not defined any particular alignment standard. Defining
your own alignment standard could be beneficial. MENCTYPE 3
and MENCTYPE 4 (A/B only) require no alignment or adjustments.
MENCTYPE 6 (A/B/I with Halls) requires the same alignment as
MENCTYPE 0 but does not require that MENCOFF be set.
When it is not practical to perform mechanical alignments, a
software adjustment can be used. MPHASE holds an offset for the
Hall channels and can be used to effectively 'shift' the Hall channel
position. It is possible to invert the effective direction as established
by the A and B channels using MFBDR. It is also possible to invert
any one or all of the hall channels. MHINVA, MHINVB, and
MHINVC allow the drive to receive the hall channels and act upon
them from an inverted nature.
B.1.5 MECNOFF
MENCOFF holds a marker offset to align the commutation in
MENCTYPE 0, MENCTYPE 1, and MENCTYPE 2. To determine
the setting for MENCOFF perform the following steps using the
®
MOTIONLINK terminal mode with power on the drive and C3
unplugged (disabled):
1. Enter ENCINIT.
2. Rotate the motor shaft two turns clockwise by hand.
3. Verify that the process is complete by entering ENCINITST. The
SERVOSTAR should return 2 if the process has been successfully
completed.
4. If not, repeat steps 2 and 3.
5. Enter SAVE.
6. Use caution to continue testing the system.
7. MENCOFF may be manually trimmed for best performance.

When using MENCOFF with MENCTYPEs 1 and 2, the correct

value must be determined through trial and error. Pick a setting and
trim it, watching for the speed (V) to be equal in both directions
when applying torque in OPMODE 2. It is common for repeated
tries of this procedure to return values that are significantly different
due to the software's reference point being different from try-to-try.
This is normal.
The motor shaft must be free to rotate uncontrolled

without damage to equipment or personnel.
NOTE
B.1.6 SYSTEM PHASING

With so many signals coming from the encoder back to the drive
and then the signals going to the motor, it can become quite
frustrating to make sure that each signal is of the appropriate
phase.
This diagram shows the commutation phasing (PFB
counts down) for:
Motors with shafts, counter-clockwise rotation
NOTE viewing shaft end.
Motors without shafts, clockwise rotation viewing
lead exit end.
Linear motors, with armature moving away from
leads.

B.1.7 TROUBLESHOOTING
Several problems can occur with encoder-based systems. The
most common problem is miswiring. The section on system phasing
(above), provides the necessary troubleshooting information.
Miswired Hall channels can cause intermittent problems. With
miswired Hall channels, the motor operates correctly sometimes,
but occasionally does not operate correctly after cycling power. It is
very important to physically verify the Hall effect channels. There is
a command in the SERVOSTAR manual called, "HALLS." It returns
the hall code as "read." It is important that the installation and
startup procedures for the machine sequence the motors through
all the appropriate hall codes to make sure they are present and in
the right sequence.
An 'illegal hall code' error occurs if the Hall channels go to all low or
all high conditions. A broken wire or misphased channel can cause
this problem.
It is important that the A and the B channels be wired appropriately
to the SERVOSTAR drive to ascertain the correct directional drive
information. This can be verified using PFB while rotating the motor
shaft clockwise. PFB should be counting in a more positive
direction. If it counts in a negative direction, the A and B channels
are inverted. To fix this, either swap the A and /A wires from the
encoder or use MFDIR.
A/B Line Break errors may occur and can be misleading. The
SERVOSTAR receives the A/B/I channels in a differential format.
Each channel is fed into a bridge rectifier to create a DC voltage
that is monitored for presence. Absence of any one of these three
voltages (except the I channel in MENCTYPE 3, MENCTYPE 4,
and MENCTYPE 6) cause an A/B line break fault.
B.1.7.1 LINE DRIVERS, RECEIVERS, AND

TERMINATIONS
Counting pulses sent over cables going through an industrial
environment requires that care be taken to prevent noise induction
on the cable that looks like an encoder pulse. Running wires in a
"clean" raceway is one requirement.
Another common sense approach is to use differential transmission
for the signals to provide the highest degree of noise immunity.
Differential line drivers are required by the SERVOSTAR. The
differential line signals follow the RS-485 format where pulses are
sent up and down a 120 Ω cable. Termination is expected at both
ends and the SERVOSTAR provides the required termination.
Deviations from a 120 Ω characteristic impedance cable when
using long cables can result in poor performance.

B.1.8 DESIGN CONSIDERATIONS

The SERVOSTAR has a maximum frequency input for incremental
encoders of 2.5 MHz. This cannot be exceeded under any
circumstance.
Encoders consume 5 V. The 5 V is typically regulated inside the
drive through a cable to the encoder. Tolerances on the 5 V must
be considered for IR loss within the cable. An 18 AWG conductor
pair providing the 5 V at a 250 mA drive result in approximately ¼ V
drop and become the limits from the encoder's 5 V rating
perspective. Consideration of cable length 5 V current draw is
extremely important for good system design. The SERVOSTAR's
encoder supply is 5 V ± 2% with 250 mA maximum draw.
When using incremental encoders, the SERVOSTAR receives the
encoder pulses, buffers them electrically and then outputs them to
the encoder equivalent output port. The phase delay in the
transport of these signals is extremely small. Be sure to run all
encoder cables in conduit or wire tray that is free from wires
carrying or emitting electrical noises such as solenoid wires and
armature cables.
B.1.9 REFERENCE VARIABLES

For additional information on any of these commands, refer to the
SERVOSTAR® CD VarCom Reference.
ENCINIT - Triggers the encoder initialization process.
ENCINITST - May be queried and returns status of the
initialization process. This variable assumes one of
three values:
0 = The initialization process has not started.
1 = The initialization process is in progress.
2 = The index position has been determined and
the initialization process is complete. The
flag is reset to zero when you manually set
the index position.
ENCSTART – Selects automatic or manual "wake and shake"
initialization.
HALLS - Reads the states on the Hall channels.
IENCSTART - Sets the "wake and shake" initialize current level.
MENCOFF - Tells the SERVOSTAR where the marker is relative
to commutation angle 0.
MENCRES - Tells the SERVOSTAR how many lines there are
on the encoder.
MENCTYPE - Tells the SERVOSTAR what encoder signals are
present.
MHINVA - Inverts the active level of Hall channel A.
MHINVB - Inverts the active level of Hall channel B.
MHINVC – Inverts the active level of Hall channel C.
MPHASE – Allows commutation offset.

B.1.10 EXAMPLE
This procedure is for commutation only and assumes analog
(OPMODE 3) operation.
1) Define a Positive Motor Direction
This is somewhat arbitrary, but must be consistent. To keep
confusion to a minimum, try to match the motor's definition of
A+/A- and B+/B- to the CD definitions for purposes of hardware
connections. With these encoder connections made, push the
motor by hand and read PFB. The motor direction which
causes PFB to become more positive is the positive motor
direction. When testing motor phase voltages and Hall phases
in subsequent steps, always push the motor in this positive
motor direction.
2) Determine the Desired Commutation Method
For this example, an encoder is used with A/B signals and Hall
sensors for commutation, but without encoder index pulse.
This allows reasonably accurate commutation without "wake
and shake" motion and without a specific index-based
commutation offset. This is equivalent to MENCTYPE=6.
3) Determine the Relationship Between Halls and Motor
Phases
Measure the motor phase voltages versus the Hall states on
an oscilloscope to determine which motor phase matches
which Hall sensor. If the zero crossings of the sine wave
match the edges of the Hall sensor, this is a match. If the Hall
sensor is low during the positive peak of the sign wave, this
follows the default polarity definition of the CD amp, so set
MHINVx=0. If the Hall sensor is high during the positive peak
of the sine wave, set MHINVx=1.
If desired, record the difference between the sine

zero crossings and the Hall edges as an estimate
of the MPHASE value to use in step 8.
NOTE
4) Determine the Correct Hall Phase Sequence
Connect the Halls to the CD, leaving other inputs/outputs
disconnected or disabled. Push the motor by hand in the
positive motor direction. Use the HALLS command to verify
that the sequence is 001, 011, 010, 110, 100, 101. Re-arrange
the Hall sensor leads until you find the combination that yields
the proper binary counting sequence while moving the motor in
the positive motor direction.
5) Determine the Proper Motor Phase Sequence
Connect motor phases to the CD. Send ZERO 1 to force the
motor to move to a known zero state. Enable the drive. This
causes motion to the zero position. Read the HALL state (it
should be 001). If this is not the Hall state, re-arrange the
motor leads and repeat until ZERO yields the proper HALL
state.

6) Save Settings
At this point, everything should be working properly. Save the
settings to the CD's EERAM and to disk.
7) Confirm Proper Commutation at All Initialization
Conditions
Disable the drive. Push the drive by hand until the HALL state
is 001. Turn off power to the drive and wait for the LED display
to go blank, then wait 5 seconds more. Turn on power to the
drive. Slowly increase positive DAC input to the drive until
motion just begins in the positive direction. Slowly decrease
negative DAC input to the drive until motion just begins in the
negative direction. The positive and negative DAC values
should be approximately the same (assuming the linear motor
is level). Repeat this process by starting from each of the six
Hall states.
8) Confirm Proper Operation in the Application Conditions
Tune the servo loop. Command aggressive moves and the
highest acceleration used by the application. Observe the peak
value of DAC input required for forward and reverse motion.
These values should be approximately the same (within about
10%). If desired/required, adjust MPHASE up or down to give
equal peak DAC output in both directions.
B.2 Resistive Regeneration

Shunt regeneration is required to dissipate energy that is pumped
back into the DC bus during load deceleration. The loads need to
be defined in terms of system inertia, maximum speed, and
deceleration time. In addition, the duty cycle must be known.
External Regen Resistor
Dimensions are in mm (inches)
White Black
26 Ω
Normally
Closed
White Black

Danaher Motion Kollmorgen 06/04 Appendix C
APPENDIX C
This Appendix describes the pulse following capability of the
®
SERVOSTAR system. In this type of position control (OPMODE =
4), the drive is synchronized to a master input command signal in
the form of a pulse train. Applications such as synchronizing one
motor shaft to another (traditionally called Master/Slaving) are ideal
for this type of feature. Another type is a stepper application where
a typical stepper motor cannot give the torque, speed, and
acceleration performance provided in a servo system. A stepper
controller can provide a master pulse train signal that becomes the
®
command for the SERVOSTAR system.
The drive is configured to read this TTL input signal as an encoder
follower, an up/down counter, or a pulse/direction counter. The
pulse train is geared to the incremental movement of the motor
shaft through the drive’s electronic gearing feature. This feature
allows for almost any integer ratio of movement to exist between
the pulse train frequency and the output shaft movement.
In this mode of operation, the drive’s homing capabilities are also
available. The Homing process is triggered through the
Configurable Inputs. Refer to the SERVOSTAR® Position Control
product note for a detailed discussion on this topic.
C.1 Basic Theory of Operation

The drive accepts an input pulse train where the rising edge of
each pulse increments (or decrements depending on the direction)
the external position counter (PEXT) of the drive one position count
(See Figure 1). This counter value is passed through a gearing
block (Electronic Gearing feature) and becomes the position
command for the motor. This position command is compared
against the actual motor position (PFB) to create a position error
(PE). The drive corrects the position error by incrementing the
motor to the commanded position.
Gearing sets up a relationship between the number of input pulses
(PEXT counts) and the position increments of the motor shaft (or
actual motor position, PFB). The rate at which position increments
of the motor shaft (motor speed) occur is determined by the gearing
relationship and the line frequency of the pulse train. The direction
of rotation is determined by the type of signal selected
(GEARMODE) and the setting of the drive’s direction variable, DIR.

Appendix C 06/04 Danaher Motion Kollmorgen
TTL
Single ended 5 VDC 150mA Sign
up to 2.9MHz IFRC
+/-
F/W Version 7.0.6 or later
PEXTHW must be set to 1
Pulse / Direction C8
GPAFR
A+ A+ 1
6
2 IGRAV
7
DGND 3 dv GPAFR2
8
B+ B+ 4 dt
9
5
GEARMODE 4
GPVFR
PEXTOFF
Up / Down C8 dp
Gearing: dt
A+ A+ 1
GEARMODE
6
= +1 counts Positon Contorller
2 GEAR
7 GP, GPI, GPD VCMD
DGND 3 PEXT Gear Ratio:
8 GPISATIN
B+ rising transition GEARI / GEARO
B+ 9
4 GPISATOUT
5
GEARMODE 5
PFBOFF
Encoder Follower C8 dp
dt PFB
A+ A+ 1
6
2
7
DGND 3
8 VEXT PE = Geared Position Command - PFB
B+ B+ 4
9
5
GEARMODE 3
Figure 1: Pulse Control Operation
C.2 Signal Types and Connections

The pulse train signal is applied through the RS-485 Remote
Encoder input (C8 connector – up to 2.9 MHz).
Various master input command signals can be applied to the drive.
All configurations count the rising edge of each pulse (Encoder
Follower also counts the falling edge). It is assumed that the
drive’s direction variable is at its default setting (DIR=1, clockwise
positive rotation).
C.2.1 PULSE/DIRECTION COUNTER

Referring to Figure 1, the pulse signal applied to the A channel
increments (or decrements depending on the direction) the external
position counter (PEXT). The line frequency and the gearing
relationship determine the speed and amount of the shaft
movement.
The direction of shaft rotation is determined by the state of the B
channel. If the signal is low, the motor turns clockwise (CW). If
high, the motor turns counter-clockwise (CCW). Setting DIR = 0 or
the sign value stored in GEARI changes this direction relationship
in the opposite fashion.

C.2.2 UP/DOWN COUNTER

When the pulse signal is applied to the A channel, the external
position counter (PEXT) increments and rotates the motor in a CW
direction. The frequency and the gearing relationship determine
the speed and amount of the shaft movement.
The pulse signal applied to the B channel decrements the external
position counter (PEXT) and rotates the motor in a CCW direction.
The line frequency and the gearing relationship determine the
speed and amount of the shaft movement.
Setting DIR = 0 or the sign value stored in GEARI changes this
directional relationship in the opposite fashion.
C.2.3 ENCODER FOLLOWER

This pulse train is an A/B channel signal. Because the drive reads
rising and falling edges, the external position counter increments up
to four times the rate of the other two methods - given the same
input line frequency. The frequency (4x, where x = line frequency)
and gearing relationship determine the speed and amount of the
shaft movement.
The direction of shaft rotation is determined by the relationship
between the A/B signal. If A leads B, the motor turns CW. If B
leads A, the motor turns CCW. Setting DIR = 0 or the sign value
stored in GEARI changes this directional relationship in the
opposite fashion.
C.3 Electronic Gearing

Gearing gives you the ability to establish any integer relationship
between the external position counter (PEXT) and an incremental
shaft movement. The feature is enabled through the GEAR switch
variable (GEAR = 1).
C.3.1 MODE OF OPERATION

The mode of operation is selected through GEARMODE. The
value stored in this variable determines which input signal type the
drive reads.
GEARMODE = 3
Encoder Follower, Remote Encoder (Connector C8) Inputs: The
encoder input channel is decoded as a quadrature input, scaled
through GEARI/GEARO, and becomes the position command for
the motor. The remote encoder ("handwheel") inputs serve as the
encoder input channel (see Note below for clarification).

GEARMODE = 4
Pulse and Direction, Remote Encoder (Connector C8) Inputs: The
encoder input channel A counts positive edges and becomes the
position command. The encoder input channel B level dictates if the
counter will count up or down. Channel B low drives motor in CW
direction. The remote encoder ("handwheel") inputs serve as the
GEARMODE = 5
Up/Down Mode, Remote Encoder (Connector C8) Inputs: The encoder
input channel is configured as a counter to command the motor’s position.
Positive edges on the A channel increments the counter (motor CW) while
positive edges on the encoder input channel B decrements the counter
(motor CCW). The remote encoder ("handwheel") inputs serve as the
The Configurable Input (INx) does not need to be

connected to enable – only to disable and mask (See
Figure 2).
NOTE
C.3.2 GEAR RATIO
The relationship between the amount of incoming pulses and the
motor shaft movement is established by the gear ratio
(GEARI/GEARO). GEARO is the output gear and GEARI is the
input.
C.3.3 DISABLING GEARING

There are two ways to disable the electronic gearing feature and
motor movement. The first is to set GEAR = 0 through serial port
communications via a host terminal. The second gives you the
ability to disable via a hardware switch through one of the
configurable inputs (See Figure 2). By setting INxMODE = 3
(where x is the input of choice), you can toggle the input active (on)
to disable gearing. However, PEXT continues to increment as long
as the input pulse signal is applied – but without motor movement.

C3 IN1 IN1MODE = 3 Gearing Disable Input (All GEARMODE options)

4 Gearing Mask Input (All GEARMODE options)
1
2
3
4
5
IN2 IN2MODE = 3 Gearing Disable Input (All GEARMODE options)
6 4 Gearing Mask Input (All GEARMODE options)
7
±12-24 8
9
10
11
12
IN3 IN3MODE = 3 Gearing Disable Input (All GEARMODE options)
13 4 Gearing Mask Input (All GEARMODE options)
Figure 2 Disabling/Masking Input Configuration
C.3.4 MASKING
The drive provides a masking switch (Figure 2) to allow you to stop
motor movement and prevent PEXT from incrementing, even
though the input pulse signal is still applied. By setting INxMODE =
4 (where x is the input of choice), you can toggle the input active
(on) to mask PEXT from the input pulse signal.
C.3.5 FOLLOWING ACCURACY

Under normal operating conditions, the drive (as a slave unit)
follows the command signal without accumulating any count error.
However, under certain conditions, counts can be lost and
inaccuracies introduced into the system’s operation. Some of these
conditions are:
• GEAR disabling (as mentioned above)
• Masking (as mentioned above)
• ACTIVE = 0 (drive is disabled)
• A fault occurs during operation
• The drive enters a HOLD state
• Drive is not in OPMODE 4 (Pulse/Direction mode)
• If PROFMODE = 1, profiling is enabled and the acceleration and
deceleration ramps are limited. If the ramps are limited below the
accel/decel ramps of the master, counts are lost. As a default,
PROFMODE = 0 and provides no limits on the ramps.

C.3.6 HOMING
Homing is also available in this mode of operation. A command (or
search) to home is initiated either through the configurable inputs
(INxMODE) or via a serial command (MH). Homing can be
performed even while pulse motion is taking place. Once the inputs
are correctly configured and the drive receives a trigger to home,
motion stops and the homing process begins. An 8 appears in the
status display (operation is still in the pulse control mode) as an
indicator that homing is in process and returns to 4 upon
®
completion. Refer to the SERVOSTAR S- and CD-Series Position
Control product note for a detailed explanation of homing
capabilities and setup.
XENCDIR
Sets the direction defined as positive rotation for the external
encoder input.
0 = normal
1 = inverted
Type: variable (R/W)
Range: 0,1
Units: n/a
Default: 0
Opmodes: all
Drive Status: dis
EEPROM: yes
XENCRES
Sets the resolution of the external encoder input channel and is
used to calculate VEXT.
Type: variable (R/W)
Range: 100 to 10,000,000
Units: Lines per revolution
Default: 1024
Opmodes: all
Drive Status: dis
EEPROM: yes
PEXTHW
Defines hand wheel connector signals.
0 - Differential
1 - TTL

C.4 Examples
To calculate a gear ratio that must be present to meet a desired
relationship between the input pulse signal and the motor shaft
movement, the counts per mechanical revolution of the motor shaft
must be known. SERVOSTAR systems provide the following
resolutions:
Resolver-Based Systems (CRxx5xx): 65536 counts/rev
Encoder-Based Systems (CExx5xx or CBxx5xx): 4 x MENCRES
lines/rev (or lines/pitch for linear motors)
C.4.1 PULSE / DIRECTION

A stepper controller is programmed to provide 1024 line pulses as
an input command to a resolver-based SERVOSTAR system to
make the motor rotate one revolution. Calculate the gear ratio
needed to accomplish this relationship (GEARMODE = 4).
Relationship = 1 = (GEARI / GEARO) x (PEXT / SERVOSTAR System Resolution)
1 = (GEARI / GEARO) x (1024 / 65536)
This ratio must be factored down because the number 65536

exceeds the upper limit of GEARO.
1 = (GEARI / GEARO) x (1 / 64)
Therefore:
GEARI = 64, GEARO = 1
Calculate the Speed for given step Freq [Hz]

n [rpm] = Freq x (GEARI/GEARO) x 60 / SERVOSTAR System Resolution
n = 10000 x 64 x 60 / 65536 = 586 [rpm]
C.4.2 ENCODER FOLLOWER

An application has two SERVOSTAR systems. You want to
synchronize one system off the other through the Encoder
Equivalent Output. The slave motor must move two CCW
revolutions for every CW revolution of the master. The following
provides the system information:
Given
Master: CR035xx with an Encoder Equivalent Output setting of 1024 lines/revolution
Slave: CE065xx with a special motor encoder resolution of 6400 lines/revolution
Relationship 1 = (GEARI / GEARO) x (PEXT / SERVOSTAR SE06 System Resolution)
Settings:GEAR = 1, GEARMODE = 3
Find: GEARI, GEARO
Calculations
PEXT = 4 x 1024 = 4096 counts/rev (rising and falling A/B transitions)
SERVOSTAR System Resolution = 6400 x 4 = 25600 counts/rev
Remember, the slave must turn two revolutions for every one of the
master. Therefore, for every 4096 counts of the master, the slave must
turn 51200 counts (2 x 25600). Let’s put this in the equation for the
system resolution of the SE06.
1 = (GEARI / GEARO) x (PEXT / SERVOSTAR CE06 System Resolution)
1 = (GEARI / GEARO) x (4096 / 51200)

This ratio must be factored down because the number 51200 exceed the
upper limit of the GEARO variable.
1 = (GEARI / GEARO) x (2048 / 25600)
Therefore:
GEARI = -25600, GEARO = 2048
where the minus sign turns the slave motor in the opposite direction
from that of the master.
Customer Support
Danaher Motion products are available world-wide through an
extensive authorized distributor network. These distributors offer
literature, technical assistance, and a wide range of models off the
shelf for the fastest possible delivery.
Danaher Motion sales engineers are conveniently located to
provide prompt attention to customer' needs. Call the nearest office
for ordering and application information and assistance or for the
address of the closest authorized distributor. If you do not know
who your sales representative is, contact us at:
Danaher Motion
203A West Rock Road
Radford, VA 24141 USA
Phone: 1-540-633-3400
Fax: 1-540-639-4162
Email: [email protected]
Website: www.DanaherMotion.com

Servostar CD Install PDF

Uploaded by

Copyright:

Available Formats

Servostar CD Install PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Servostar CD Install PDF

Uploaded by

Copyright:

Available Formats

KOLLMORGEN

© Copyright 2000 - 2004 Danaher Motion - All rights reserved.

Alerts you to potential physical danger or harm. Failure to follow

Directs attention to general precautions, which if not followed,

Highlights information critical to your understanding or use of the

SERVOSTAR CD Installation M-SS-017-01 Rev. T i

ii M-SS-017-01 Rev. T SERVOSTAR CD Installation

iv M-SS-017-01 Rev. T SERVOSTAR CD Installation

1.1 UCB2 Digital Control Board

SERVOSTAR CD Installation M-SS-017-01 Rev. T 1

1.2 New Features

2 M-SS-017-01 Rev. T SERVOSTAR CD Installation

2 READ BEFORE INSTALLING

SERVOSTAR CD Installation M-SS-017-01 Rev. T 1

15. Using the Startup Wizard in MOTIONLINK:

2.1 Use As Directed

2 M-SS-017-01 Rev. T SERVOSTAR CD Installation

3 UNPACKING AND INSPECTING

3.1 New Description Label

Model Number Firmware Version

3.2 Series 5 Part Number Guide

Feedback Cont. Current Logic Power Control Interface

SERVOSTAR CD Installation M-SS-017-01 Rev. T 3

3.3 Series 2 Model Numbers

Manufacturing Unit Manufactured

SERVOSTAR® Amplifier Family Motor Winding

Feedback Motor Family

250 replaces previous standard option (200) originally

4 M-SS-017-01 Rev. T SERVOSTAR CD Installation

4.1 Hardware Specifications

4.2 Control Specifications

SERVOSTAR CD Installation M-SS-017-01 Rev. T 5

Product Model Control Specifications

4.3 Outline Dimensions

6 M-SS-017-01 Rev. T SERVOSTAR CD Installation

SERVOSTAR CD Installation M-SS-017-01 Rev. T 7

8 M-SS-017-01 Rev. T SERVOSTAR CD Installation

5.3.1 NON-INSULATED CABLE CLAMP

Terminal Clamp Cx Drive Clamp

5.3.2 ALTERNATIVE BONDING METHODS

Phoenix Contact - Side View and Phoenix Contact -Top View

SERVOSTAR CD Installation M-SS-017-01 Rev. T 9

Copper bus bar

K(8, 14, 20, - Shielded terminal block

Phoenix Contact - Side View

Copper Bus Bar

High frequency ground

Phoenix Contact -Top View

5.4 CE Filtering Techniques

10 M-SS-017-01 Rev. T SERVOSTAR CD Installation

5.4.1 INPUT POWER FILTERING

SERVOSTAR CD Installation M-SS-017-01 Rev. T 11

5.4.2 MOTOR LINE FILTERING

Never wrap a ground lead through a core.

From Drive Output

Common mode currents commonly occur from noise spikes created

12 M-SS-017-01 Rev. T SERVOSTAR CD Installation

Manufacturer’s Danaher Motion

5.4.3 I/O FILTERING