GYROSCOPE

NX3 3D Flight Controller Gyroscope Balance For Fixed-wing Aircraft

Feature:
1.Four Model Types supported: single aileron, dual ailerons , flapperons, delta and vtail.
2.Three Flight Modes supported:
a. Rate Mode ,Rate Mode for offset correction.
b. Hold Mode ,HOLD mode for attitude hold
c. Gyro Off Mode,transsmiter control the plane directly.
3.Two kinds of Gain Control Method supported:Master Gain from the radio, Independent Axis
Gain from the Variable resistor on the Controller board.
4.Using superior algorithm, Bring a more comfortable and more sensitive sense of control .

VERY IMPORTANT :
The Controller has to re-learn center position after installation,or replacing a new radio
system, or making a trimming(or Sub-Trim)change within the transmitter, otherwise the servos
may move to one side automatically when switching to hold mode.To do this,just quickly flip
the flight mode switch twice between rate mode and hold mode within 1 second!

Status LED Description:

WARNING :
PLEASE READ THE FOLLOWING STEPS VERY CAREFULLY BEFORE YOU START TO INSTALL A NEW
PLANE!

Step 1:Mounting
The board need to be firmly mounted near the center of the gravity of the plane by using the
double-tape provide.Please make sure the longer side of the board is along with the heading
direction.After mounting ,please check again if the board is attached firmly in the plane.
Step 2:Model Type Selection
The DIP switches set the WING mode,Please match the type of your aircraft with Normal
Airplane(single aileorn),Normal Airplane(dual aileron for flapperon), Delta-wing (Flywing-
wing)and V-tail according the pictures 1 to 4. if you change any DIP switch settings, power
cycle the device to enable the new setting to take effect.
Step 3:Wiring
Please connect the control board and the radio receiver using wires provide according the
pictures 1 to 4.Pay attention to the color of wires to avoid anti-plug.
Step 4:Switch and Master Gain Channel Configure
Assign a 3-pos switch to the channel which connected the pins”IN-4”(AUX-IN) for switching the
flight mode in flight.When use a 2-pos swtich,you can only switch between Rate Mode and
Hold Mode,So you can not switch to Gyro Off Mode.It will be set to Rate Mode by default if
switch channel is not connected to the board. If your transsmiter has Travl Adjust
Function(End Point Adjust Function),you can change the switch channel’s End Point to change
Master Gain.
Step 5:Gyro direction and Gyro Gain configure
Befor flight, you have to verfy that the gyro compensation direction is OK, otherwise, it could
lead to losing control or even crash during the flight!the VR gain POTs on the NX3 control the
correction gain and direction for each of the pitch (ELE), roll (AIL) and yaw (RUD) axis.
5 o'clock = max gain in one direction
12 o'clock = zero gain
7 o'clock = max gain in opposite direction
To perform the examination,power on the
board,pick the plane up and check it by
following the six steps below:
Step 6: re-learn center position
Quickly flip the flight mode switch twice between rate mode and hold mode within 1 second!
Thanks for using NX3 Flight Controller. if u have any questions, plz feel free to contact
[email protected]

Packing Included:
1 x NX3 Flight Controller board
1 x NX3 manual
5 x wires
1 x double-side tape.
F06670 Thunder P1-gyro 3-axis Flight Controller Stabilizer System Gyro for Fixed Flying Wing
Airplane FPV
Description:
Size:26*39mm
Weight:about 6g
Working Volt:3.5-6v
First Usage,please install and debug as manual.
Sensitivity debug,we suggest that in lowest position in maiden flight,and according to add 5
mins range Each to process the Test flight adjustment.When the flight controller factory
settings,in 50% position,please do not put the set factory settings as standard,and adjust right
sensitivity according to your airplane and power parameter.

Features:
P1-GYRO Products in A3 on the basis of three-axis stability augmentation to increase the flight
control switch control mode and the axis lock (AVCS) mode.
This mode uses the angle vector control algorithm, the aircraft angle of around three axes of
motion detection and correction in real time offset , the aircraft has always maintained the
ability to pose on a time and trends , so called lock.
Locked compared with the ordinary horizontal mode , the lock mode can not only greatly
enhance flight stability , even in the absence of control ( off control ) in the case , to achieve
self- hoists, and other difficult moves side to fly.
P1-GYRO Products added a switch channel is used to switch modes during the flight ,you can
use a three -stage switch in the general augmentation , triaxial lock (AVCS) and gyroscopes
closed three kinds of flight between modes at any time switch to experience a completely
different flight fun.
P1-GYRO Products flight control of the aircraft electric oil moving aircraft wingspan unlimited
size , general- flight controller.
Flight line controller can improve aircraft performance and controllability of the aircraft .
Meanwhile various effects can be offset by the state aircraft external factors such as ease of
stall of the aircraft, or had bad shape design to fly aircraft. Well as wind and airflow ,
etc.,automatic flight control can offset these negative factors .
Precision three-axis flight control on the right rudder gyro can make rapid and sensitive
unstable airflow offset compensation operation of the aircraft in flight more stable and
straight ,to a certain extent in the wind will not be bumpy .
But at the same flight control will offset your control of the airplane , on the contrary will
increase your sense of control of the aircraft

Video Shows:
http://v.youku.com/v_show/id_XMzg3NjAzMzAw.html
http://v.youku.com/v_show/id_XMzc4NTE1Mzg0.html
http://v.youku.com/v_show/id_XMzc3NTcyOTg0.htmll
http://v.youku.com/v_show/id_XMzc1ODA1NzA4.html
http://v.youku.com/v_show/id_XMzcwOTY3OTUy.html
http://v.youku.com/v_show/id_XMzYxODg3ODAw.html
http://v.youku.com/v_show/id_XMzUyNjI2OTcy.html
http://v.youku.com/v_show/id_XMzczNDA3NzQw.html

(As video Showed,it worked with 3D series Airplane,if you use not on 3D series,such as The
glider and other small servo surface plane,the effect will not good as video showed,Please
purchase before serious consider.Thanks)

Package Included:
1x P1-gyro 3-axis Flight Controller Gyro Set

Volantex Xpilot AX601 6-Axis Flight Stabilizer

Features:
- Easy to Setup
- 6-Axis Advanced Gyro
- Two different level switch-able
- Separate switcher to Adjust 3 Axis PDI

Package Included:
1x Volantex Xpilot AX601 6-Axis Flight Stabilizer
Upgraded NX3 Evo Flight Controller Autobalance For RC Airplane
Description:
Voltage range: DC 4.5 – 6V
Response Frequency: 100Hz
Operating Temperature: 0-50°C
Dimension: 43 x 28 x 15mm
Weight: 11g

Features:
Provides four levels of flight modes: 1- Beginner; 2 - Practice; 3 - Intermediate; 4 - Expert.
Support normal fixed-wing copter, V-tail, triangle-wing
Using the latest high-performance six-axis MEMS sensor
Independant potentiometer adjust axis sensitivity
Auto distinguish normal single flybar and dual flybar mode
Smart level calibration,remote master gain adjustment during flight
Auto balance flight
One button save function
Attitude locking mode
Provide Y-wiring for aileron

Package Included:
1x NX3 Evo flight controller
1x Accessories
1x Manual