TB 326

IRRIGATED MAIZE PRODUCTION IN THE TOP END
OF THE NORTHERN TERRITORY
PRODUCTION GUIDELINES AND RESEARCH RESULTS

DISCLAIMER
While all care has been taken to ensure that information contained in this Technical Bulletin is true
and correct at the time of publication, changes in circumstances after the time of publication may
impact on the accuracy of its information.
The Northern Territory of Australia gives no warranty or assurance, and makes no representation as
to the accuracy of any information or advice contained in this Technical Bulletin, or that it is suitable
for your intended use.
You should not rely upon information in this publication for the purpose of making any serious,
business or investment decisions without obtaining independent and/or professional advice in
relation to your particular situation.
The Northern Territory of Australia disclaims any liability or responsibility or duty of care towards
any person for loss or damage caused by any use of or reliance on the information contained in this
publication.
September 2007
Fergal O’Gara
Crops, Forestry and Horticulture Division
Technical Bulletin No. 326
Northern Territory Government

Department of Primary Industry, Fisheries and Mines
GPO Box 3000
Darwin NT 0801
http://www.nt.gov.au/dpifm
ISBN: 978 0 7245 4725 8

CONTENTS
ACKNOWLEDGEMENTS _____________________________________________________v
INTRODUCTION ____________________________________________________________1
SELECTING A SUITABLE VARIETY ____________________________________________2
SOIL TYPE AND LAND PREPARATION _________________________________________2
PLANT POPULATION, PLANTING RATE AND ROW SPACING ______________________4
TIME OF PLANTING _________________________________________________________6
Are two maize crops per year possible? ____________________________________________ 8
NUTRITION ________________________________________________________________9
Nitrogen (N)___________________________________________________________________ 10
Phosphorus (P)________________________________________________________________ 12
Potassium (K) _________________________________________________________________ 12
Sulphur (S) and magnesium (Mg) _________________________________________________ 13
Trace elements ________________________________________________________________ 13
Nutrient availability and soil pH __________________________________________________ 13
Timing and application of crop nutrients___________________________________________ 14
Fertigation____________________________________________________________________ 15
DISEASE AND INSECT CONTROL ____________________________________________16
Soil insects ___________________________________________________________________ 17
Other major pests______________________________________________________________ 17
Chemigation for pest control ____________________________________________________ 21
Crop scouting _________________________________________________________________ 22
Integrated pest management (IPM)________________________________________________ 23
Pesticide use and chemical registration ___________________________________________ 25
WEED CONTROL IN MAIZE__________________________________________________26
Weeds of significance __________________________________________________________ 28
IRRIGATION MANAGEMENT_________________________________________________29
Using a water balance approach to schedule irrigation _______________________________ 30
Using soil moisture sensors to schedule irrigation __________________________________ 33
Irrigation system capacity _______________________________________________________ 35
Water planning and allocation ___________________________________________________ 37
NATIVE AND FERAL ANIMAL DAMAGE _______________________________________38
HARVESTING _____________________________________________________________39
MAIZE AS A SOURCE OF FODDER AND ENERGY_______________________________40
THE ECONOMICS AND FUTURE OF IRRIGATED MAIZE PRODUCTION IN THE NT ____41
Current and potential market ____________________________________________________ 41
Gross margin for a single irrigated maize crop______________________________________ 41
iii
WORLDWIDE DEVELOPMENTS IN MAIZE PRODUCTION AND TECHNOLOGY_______ 44
GLOSSARY ______________________________________________________________ 46
APPENDICIES ____________________________________________________________ 48
Appendix 1. Useful websites _____________________________________________________48
Appendix 2. Maize Crop Growth Stages and Management Guide _______________________49
Appendix 3. Evaluation of Irrigated Maize on Blain Soils, Douglas Daly Research Farm,
1999 to 2002 ___________________________________________________________________51
Dry Season 1999 ____________________________________________________________52
Dry Season 2000 ____________________________________________________________61
Dry Season 2001 ____________________________________________________________65
Dry Season 2002 ____________________________________________________________72
REFERENCES ____________________________________________________________ 76
TABLE OF FIGURES
Figure 1. Press-wheels such as “twin inclined” will assist germination on red soils provided the surface
remains moist until emergence .................................................................................................................. 3
Figure 2. Oolloo soil is a free draining sandy loam red earth ........................................................................... 3
Figure 3. Optimum and uniform plant stands are critical for achieving high yields of maize............................ 6
Figure 4. Mean, highest and lowest maximum temperatures at DDRF (1968-1999) ....................................... 7
Figure 5. Average daily evaporation at DDRF (1968-1999) ............................................................................. 8
Figure 6. Maize growth periods and nutrient uptake....................................................................................... 11
Figure 7. N deficiency (light stunted plants) due to uneven application of fertiliser........................................ 12
Figures 8 and 9. Early nutrient deficiency in young maize on sandy surfaced soils...................................... 13
Figure 10. Schematic plan of fertiliser placement in relation to seed ............................................................. 15
Figure 11. Fertigation tank for applying nutrients in the irrigation water......................................................... 15
Figure 12. Potato leafhopper adult and nymph, similar to the maize leafhopper ........................................... 18
Figure 13. Effects of WEV............................................................................................................................... 19
Figure 14. Healthy plants on left and stunted plants on right, affected by WEV ............................................ 19
Figure 15. Heliothis caterpillar ........................................................................................................................ 19
Figure 16. Green vegetable bug and eggs on maize...................................................................................... 20
Figure 17. Northern armyworm damage ......................................................................................................... 20
Figure 18. Heliothis (left) attacking ear and armyworm feeding on leaf ......................................................... 20
Figure 19. Trichogramma wasp parasite on heliothis egg .............................................................................. 21
Figure 20. Spider predating an insect............................................................................................................. 21
Figure 21. Assassin bugs feed on caterpillars ................................................................................................ 21
Figure 22. Ladybirds feed on aphids and other soft pests.............................................................................. 21
Figure 23. Chemigation unit used for applying pesticides through irrigation water ........................................ 22
Figure 24. Insect scouting is an essential part of pest management in cropping systems............................. 23
Figure 25. Conventionally tilled maize with pre-emergent herbicide showing excellent weed control ........... 27
Figure 26. Row sweepers on a conservation tillage planter, which “sweep” the row clean of mulch to allow
the seed to be planted without obstruction .............................................................................................. 28
Figure 27. Daily evaporation rates (mm/day) from March to October 1998 ................................................... 32
Figure 28. Enviroscan® chart showing moisture extraction at various depths............................................... 34
Figure 29a and b. Enviroscan® capacitance sensors and data logger ......................................................... 34
Figure 30. Installing an Enviroscan® in a maize crop .................................................................................... 35
Figure 31a. Tensiometers at different depths in a peanut crop and b. Tensiometer with gauge ................... 35
Figures 32a and b. Different sprinkler heads will give different efficiencies. Wobbler type sprinklers (left)
reduce drift and evaporative losses in high winds and hot conditions..................................................... 38
Figure 33. Damage to a maize crop caused by sulphur-crested cockatoos................................................... 39
iv
ACKNOWLEDGEMENTS
The author gratefully acknowledges the use of information accessed from Pioneer Hi-Bred and Pacific Seeds
on varieties and nutrition. Pacific Seeds, Pioneer Hi Bred and Genex generously provided seed for these
trials. Information on insect pests and pesticide use on pages 28, 29, 32 and 33 was sourced and adapted
from the Queensland Department of Primary Industries and Fisheries.
The author also acknowledges the contribution of Steve Lucas, Technical Officer DDRF and Chris Ham,
Agronomist who assisted in the planning and management of this evaluation. Carole Wright and Mark
Hearnden provided advice on design and statistical analysis. DDRF management and staff provided
excellent support in machinery repair and harvesting. Hassan Bajhau and Rowena Eastick, DPIFM Darwin,
provided editorial assistance in the publication of this document.
v
INTRODUCTION
Maize, which is a native of Mexico, is one of the oldest and most productive cereal food crops. It is the third
most planted crop after wheat and rice. However, with approximately 600 million tonnes produced each year,
it is the leading cereal in terms of production. It is grown throughout the world for human and animal
consumption. The Food and Agriculture Organisation of the United Nations estimates the demand for maize
for human and animal consumption will increase by nearly 300 million tonnes by 2030, which does not
include the increased demand for bio-fuel production.
Maize is being increasingly used for industrial purposes, such as the production of starches, bio-degradable
plastics and ethanol. In the US, the price of maize (corn) doubled between 2006 and 2007 due to an
increasing demand from the ethanol industry. Maize is still a minor crop in Australia, but is gaining
prominence due to its high yield potential and many uses. The use of maize in bio-fuels is increasing each
year to feed a rising demand for alternative fuels.
Maize was grown by the first white settlers in the Northern Territory (NT) as far back as 1824. Research in
rain-fed (dryland) maize began in 1954 in the NT when the Animal Industry and Agriculture Branch of the NT
Administration conducted trials at Berrimah, Batchelor and Tortilla Flats. Trials continued until 1963.
However, yields were variable due to weeds, waterlogging, seed-set failures and diseases such as “wallaby
ear” virus (WEV).
Dryland maize trials were conducted at Douglas Daly Research Farm (DDRF) from the early 1980s to the
early 1990s. DDRF is located at the junction of the Douglas and Daly Rivers, (13º50´ S, 131º45´ E, altitude <
200 m), 220 km south-west of Darwin. Commercial maize production was supported by the NT Government
as part of its policy to promote agriculture in the north (Agricultural Development and Marketing Authority).
Commercial dryland maize was grown in the Douglas Daly region for about 12 years but crops invariably
suffered from high soil temperatures at emergence, nutritional deficiencies and moisture stress at flowering.
Many of the nutritional deficiencies, establishment and soil temperature related problems were experienced
on the lighter sandy-surfaced soils. Maize generally performed better on the heavier clay loams due to their
higher nutrient and moisture-holding characteristics. Paddock yields of 4.0 to 5.0 t/ha were recorded but the
average yield for the region was approximately 3.0 t/ha. Cattle, pasture and hay crop production largely
replaced grain production in the region in the mid 1990s.
Maize is essentially a warm season rather than a hot season crop. It is not well-adapted to the harsh, hot
conditions in the Top End during the wet season. Although it performed poorly under rain-fed conditions in
the NT, maize yields of over 10.0 t/ha were achieved under irrigation in Katherine and Kununurra in the
1980s (Muchow 1989; Warren 1982). The first commercial irrigated maize was produced in Katherine in the
early 1990s on what was then known as Hickey’s Farm. Grain yields of between 9.0 t/ha and 11.2 t/ha were
reported. Maize silage has been produced for several years on what was formerly Rowland’s Dairy at
Katherine.
The Department of Primary Industry, Fisheries and Mines (DPIFM) conducted a four-year (1999-2002)
evaluation of irrigated maize on “Blain” soil (sandy textured red earth) at DDRF. The objective was to identify
the best adapted varieties and determine the agronomic requirements for producing dry season irrigated
maize in the NT. The trials confirmed the potential of irrigated maize with yields approaching 13.0 t/ha. The
average yield for all varieties over four years was 9.3 t/ha.
Maize is one of the most researched crops and a lot of information is available on its production and
management. This Technical Bulletin is not intended to replace available information. It is intended to
provide information relating specifically to management issues of dry season irrigated maize production in
1
the Top End to assist those who wish to grow the crop in this environment. Many of the guidelines in this
Technical Bulletin are based on results obtained from a four-year trial (see details of the trial in Appendix 3).
SELECTING A SUITABLE VARIETY
Selected maize varieties should have a high yield potential, good disease and insect tolerance, good
resistance to lodging and a maturity length to suit environmental conditions. A medium maturity variety is a
good compromise between yield and water requirement. Tight husk covers offer resistance to heliothis
caterpillars. Table 1 lists the varieties which performed well in evaluations under irrigation at DDRF. New
improved varieties are being constantly developed and information on them can be obtained from
commercial seed companies and DPIFM.
Table 1. Maize varieties trialled and recommended for commercial irrigated production in the Top End
Variety Uses Maturity (days Resistance to Husk cover Average

to relative disease, insects trial
maturity) and lodging yields*
(t/ha)
Pioneer 3237 Feed and silage Medium Good medium tight 10.9 three
(116-120 days) trials
Pioneer 3153 Feed and silage Medium Good tight 10.4 three
(116-120 days) trials
Hycorn 424 Feed and silage Medium quick Good medium 11.3 two
(113-115 days) closed trials
Hycorn 901 Feed and silage Medium Good tight 11.6 one
(116-120 days) trial
Pacific 675 Feed and silage Medium Good medium tight 12.7 one
(116-120 days) trial
*Yields taken from 0.5 ha, machine harvested irrigated trials at DDRF from 1999 to 2002.
The major disease of concern at present in the NT is WEV, which causes stunting and a dramatic reduction
in yield. It is transmitted by leaf-hoppers which inject a toxin while feeding on the plant. There are no
varieties that are resistant to WEV. Disease prevention is through pre-treating the seed with a systemic
insecticide to reduce the build up of the leaf-hopper vector.
Queensland and NSW have diseases such as Johnson grass mosaic virus, leaf blights and rusts. These
diseases are not prevalent in the NT at present due to the limited areas of maize production.
SOIL TYPE AND LAND PREPARATION
Maize will grow in the NT on most soils in the dry season provided sufficient moisture and nutrients are
available. However, it will perform best on fertile, friable and well drained soils with a pH range of 6.5 to 7.5.
Maize is suited to the red-earths, including sandy Blain and Oolloo soils as well as the heavier Tippera and
Tindal clay loams.
Maize can be sown conventionally into a fully cultivated seed bed or sown zero-till into mulch. The method
will depend on soil type and condition, availability of machinery, grower preference and experience.
Seed should be planted at a uniform depth of 3.0 to 4.0 cm into moist soil. Sufficient soil cover and firm
seed-soil contact is required for optimum establishment. Rolling the soil or using press-wheels will enhance
emergence provided the soil surface is kept moist until seedlings have emerged.
2
Compacted furrows (in red earth soils) that dry out prior to emergence will crust and impede establishment. If
the soil is rolled or the furrows are compacted with press-wheels, the soil surface should be kept moist until
all seedlings have emerged. Crusting can be a problem on Tippera clay loam soils under conventional
tillage.
Figure 1. Press-wheels such as “twin inclined” will assist germination on red soils provided the surface
remains moist until emergence
Figure 2. Oolloo soil is a free draining sandy loam red earth
3
PLANT POPULATION, PLANTING RATE AND ROW SPACING
Achieving an optimum plant population is one of the most critical aspects of maize production. A survey of
549 maize producers in the US found that most believed that plant population and nitrogen were the two
most important factors in determining crop performance (Pioneer Seeds Maize Workshop Notes).
Sowing rate is determined by the desired population, germination percentage, the expected establishment
rate, row spacing and the number of seeds per kilogram. Seed size varies from 4400 (small) to 2500 (large)
seeds/kg. Seed is separated into round and flat grades. Refer to the bag for an exact seed count and
germination percentage (minimum germination specified is usually no less than 85%). Not all seeds planted
will germinate and establish so planting rate needs to account for these losses.
Seed companies recommend plant populations for specific varieties and conditions. The better the growing
conditions, the higher the plant population recommended. A population of between 70 000 and 85 000 plants
per hectare is generally recommended for fully irrigated maize, depending on variety.
Row widths of 75 cm or 90 cm are the most common and must match harvest machinery. In the NT, 75 cm
rows are preferable for quicker canopy closure, reduced soil surface evaporation and suppression of weeds.
There is a trend to reduce row widths to 50 cm in many areas. Trials in the US and in Australia have shown
yield improvements of 5% to 10% with narrow rows in some instances. The benefits of narrow rows are
generally achieved under good growing conditions and in irrigated crops.
Table 2. Sowing rate and seed spacings for different sized seed at 90 cm row spacing
Desired plant Number of seeds/kg Average seed

population/ha spacing (cm)
2500 3000 3500 4000
Sowing rate (kg/ha) for

respective seed sizes
50 000 24 20 17 15 19
60 000 28 24 20 18 16
70 000 33 27 24 21 13
80 000 38 31 27 24 12
Note: Average seeding rates based on 85% germination rate and 100% emergence rate
The following calculation can be used to determine the sowing rate:
Sowing rate = desired population ÷ seeds/kg ÷ germination% ÷ emergence%
Sowing rate:
• Sowing rate = seed planted (kg/ha)

• Desired population = target number of plants per hectare (e.g. 75 000)
• Seeds/kg is indicated on the seed pack (e.g. 3000)
• Germination % is indicated on the seed pack (expressed as a decimal e.g. 85% is 0.85)
• Emergence % is the percentage of seeds that actually emerge to become viable plants e.g. 90%
4
Working example:
Sowing rate = 75 000 (desired plant population) ÷ 3000 (seeds/kg) ÷ 0.85 (minimum germination %) ÷
0.90 (establishment %)
Sowing rate = 32.6 kg of seed/ha (for a population of 75 000 plants per hectare)
Uniform establishment and evenly spaced plants are critical for achieving high yields. Gaps or crowded
plants will reduce crop yield. Using purpose built, precision row-crop machinery is necessary for establishing
optimum plant stands.
Different planters will give different establishment results. Modern row-crop planters will give field
establishment rates of up to 90% or greater. Older machinery may only give 50 to 60% establishment and
therefore higher rates of seed will be needed.
Calculating seed spacing along the row
This calculation is used to calibrate the planter to sow at the required rate:
Distance between seeds in a row (m) = (10 000 ÷ row width (m)) ÷ (sowing rate (kg/ha) x (seeds/kg)
Working example:
• Seed required = 32.6 kg

• Seeds/kg = 3000
• Row width (m) = 0.9
• Square metres /ha = 10 000
Distance between seeds (m) = (10 0000 (Sq m/ha) ÷ 0.9 (row width)) ÷ (32.6 (sowing rate) x
3000 (seeds/kg))
Distance between seeds = 0.11 m or 11 cm (each seed should be 11 cm apart)
When precision planters are calibrated correctly, seeds will be spaced evenly along the row at a specific
distance to achieve the desired population. If seeds are closer or more widely spaced than the specified
distance, the planter may need re-calibration. Seed companies supply charts which specify seed spacing for
different row widths and populations.
5
Figure 3. Optimum and uniform plant stands are critical for achieving high yields of maize
Key points:
• Optimum plant population is one of the most

critical aspects in achieving top maize yields
• 70 000 to 85 000 plants/ha is optimum for most

irrigated maize varieties
• Narrow row spacings will assist in moisture

conservation, weed suppression and enhanced
yields.
TIME OF PLANTING
Maize can be grown as a rain-fed (i.e. dryland) wet season crop, a supplemented irrigated crop or a fully
irrigated crop.
Rain-fed crops are planted in mid to late December and harvested in late April. They rely solely on seasonal
rainfall, which is intense, with intermittent periods of moisture stress. The duration and timing of the dry
spells will largely dictate crop yield. If late February/March is dry (i.e. coinciding with tasselling and
fertilisation) yield will be significantly reduced.
Managing nutrients and weeds is also a challenge due to the potential for intense rainfall to leach fertiliser
and herbicide out of the root zone. As a result maize is recommended for the heavier clay loam soils due to
their better moisture holding capacity and nutrient retention. Rain-fed maize is recommended for the Douglas
Daly area and north due to better seasonal rain reliability. Rain-fed maize yields have been historically low in
the Top End. However, maize has potential as a dryland crop if it is grown on the best soil types with careful
attention to varietal selection and agronomy.
6
Supplementary irrigated crops can be planted from December through to late January. February is the
wettest month in the Top End and in many seasons access to land during this period is restricted. This
means to take advantage of February and March rainfall, crops need to be established by mid January
before conditions get too wet. Irrigation will then be required in late March to April to finish-off the crop. One
or two irrigations may be required depending on duration of the wet season.
Fully irrigated crops are planted at the end of the wet or early dry season, (late February to early April)
depending on seasonal conditions. Apart from some residual soil moisture remaining from the wet season,
the crop is entirely reliant on irrigation throughout the growing season. Planting while temperatures are high
and there is residual moisture helps to ensure that the crop establishes quickly and may save on initial
irrigation costs. Early dry season planted crops mature in the coolest part of the dry season (July/August),
reducing heat stress, respiration losses and total crop water requirement.
AVERAGE TEMPERATURE DATA FOR DDRF
45
40
35
30
TEMP IN CELCIUS
25
20 MEAN MAX
HIGHEST MAX
LOWEST MAX
15
March to August has the most

10 suitable temperature for dry
season maize production.
5
0
JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC
MONTH
Figure 4. Mean, highest and lowest maximum temperatures at DDRF (1968-1999)
Planting maize in May or June means the crop will mature in the hottest time of the year (late September to
October) when evaporative demand and respiration losses are highest. The ideal day time temperature for
maize is between 25°C and 32°C which coincides with mid-dry season temperatures. August has the highest
number of sunshine hours (> 300 per month), which promotes high crop productivity. After August,
temperatures increase beyond the optimum range and heat stress can affect the crop.
Research in the US has shown that moisture or fertility stress at tasselling through to pollination can reduce
yield by 8% to 13% each day stress occurs. Water stress accelerates the maturation process resulting in
smaller grains and lower yields. Temperatures above 32°C at pollination can result in kernel abortion.
September and October temperatures may be as high as 38°C to 40°C in the Daly and Katherine regions.
High night time temperatures also reduce maize yields by increasing respiration losses.
7
M E AN E VAP ORATION FOR DDRF

9
6
E VA PO RA TION IN M
MEAN EVAPORAT ION

4
Period w hen evaporation is

2
low est and coincides w ith the
optim um period for grow ing
1 irrigated m aize.
0
JA N FE B M AR A PR MAY JUN JUL A UG S EP OC T NO V DE C
M O NTH
Figure 5. Average daily evaporation at DDRF (1968-1999)
ARE TWO MAIZE CROPS PER YEAR POSSIBLE?
In theory, growing two maize crops in 12 months is possible using irrigation. However, there will be logistical
and agronomic problems to overcome. Provided agronomic issues are well managed, it may be possible to
plant a supplementary irrigated or rain-fed crop in November to December and a dry season (fully irrigated)
crop in late April or May.
Double-cropping may be an economic imperative due to the capital cost of establishing, running and
maintaining irrigation infrastructure. It also makes more efficient use of natural resources (soils, wet season
rainfall, solar radiation and land), machinery and labour units.
Peanut producers trying to double-crop found that wet season crops had relatively low yields and often
compromised the planting of the dry season crop. Due to the variable conditions in the wet season, maize
crops are likely to have lower yields than dry season crops. Intermittent dry spells, water-logging, lower
radiation levels, above optimum temperatures and the difficulty in managing nitrogen nutrition and pests are
factors which may contribute to lower wet season maize yields.
Research by CSIRO in Katherine showed that maize yields were not significantly different when planted on
October 10, February 6 and August 20. However, maize crops planted before early November will mature in
the wet-season making dry-down and harvest almost impossible.
Research in the US has shown that growing maize after maize reduces yields by between 10% and 20%
compared to maize which follows soybeans, even when high rates of nitrogen are applied to the second
maize crop. Similar results were reported by CSIRO’s early research at Katherine when sorghum was grown
after sorghum. Clearly there are several unexplained factors at work and these issues have not been
researched recently in the NT. The performance of double-crop maize in the NT is still an unknown.
8
The objective of double-cropping should be to maximise economic returns without compromising the
performance of either crop or the degradation of natural resources. Planting at the optimum time and
maintaining viable yields while avoiding soil degradation will be some of the challenges for double-cropping
in the NT.
Double cropping will only be successful when the following agronomic and resource issues are effectively
managed for both crops:
• Stubble management
• Planting on the optimum dates
• Managing nutrient and water requirements for each crop
• Insect, disease and weed pressure and their changing dynamics
• Water allocation and irrigation requirements
• Conserving soil, its health and fertility
• Managing labour units and equipment
• Developing a farming system which reduces farm inputs and enhances yields
• Finding suitable rotation crops.
Key points:
• Maize is a warm season crop and is not suited to

extended periods of hot weather and moisture
stress
• Planting in early dry-season allows the crop to

mature under mild conditions, reducing water
demand and irrigation costs
• Mild day and night temperatures at pollination

and grain fill will enhance grain size and yield
• Two crops per year may be a possibility provided

many of the timing and logistical issues are
managed.
NUTRITION
Maize is a high input crop and requires good nutrition and adequate moisture to achieve high yields. The
amount and type of nutrient required for a maize crop will be determined by:
• Previous cropping/fertiliser history

• Expected yield and management
• Soil type, pH, condition and soil test result.
If fertiliser history is good or legumes have been grown, the amount of applied nutrients may be reduced in
some instances. Regular soil testing will help determine the level of nutrient required and reduce possible
deficiencies or over application. Foliar analysis will also assist nutrient management.
Nitrogen (N) is the most limiting element in maize production and is taken up in the greatest quantity.
9
Phosphorus (P) and potassium (K) are the next major elements required and also taken up in large
quantities. N, P and K account for about 83% of the total nutrients taken up. Sulphur (S), calcium (Ca) and
magnesium (Mg) make up another 16%. Trace elements such as zinc (Zn), copper (Cu), molybdenum (Mo)
and boron (B) make up about 1% of the nutrients taken up. The trace element content of Territory soils is low
especially on the sandy red earths. Maize is particularly sensitive to Zn deficiency and addressing low levels
is essential for viable production.
Nutrients need to be balanced to ensure they are available in the required quantities at the right time. Once a
deficiency is identified in maize, yield will have already been affected. If one essential nutrient is lacking yield
will be reduced regardless of how much other nutrients are applied.
This is referred to as the “law of the limiting” where a crop will only grow as well as the most limiting factor
allows it. Research in the US has shown an interaction between P and Zn. When both the P and Zn were
low, the addition of either P or Zn alone had no effect. However, applying both elements resulted in an
increase in maize yield.
NITROGEN (N)
Adequate N is critical in achieving high yields. N deficiency will result in pale stunted plants with a typical V-
shaped yellowing running from the tip of the leaves. N is the building block of plant material and protein. A 10
t/ha grain crop will contain about 160 to 180 kg/ha of N in the grain depending on grain protein. Another 100
kg/ha of N will be taken up in the stover.
The total quantity of N required to grow a maize crop is approximately 1.6 times the amount taken off in the
grain. The yield and the protein level of the grain will determine N removal. A 10.0 t/ha crop with a grain
protein level of 10% will remove 160 kg of N per hectare. The requirement for the entire crop (grain and
stover) will be 160 X 1.6 = 256 kg N. This guide will work for any yield assuming a grain protein of around
10%.
10
Figure 6. Maize growth periods and nutrient uptake
N needs to be available immediately after germination for vigorous establishment. From week 4, maize takes
up large quantities of N and grows rapidly. During weeks 5 to 10, maize takes up approximately 80% of its N
requirement. If N runs low during this period, yield will be significantly reduced. At peak growth rates, maize
takes up 4.0 kg/ha/day of N.
N application will be determined by the target yield, cultivation practice, mulch levels and the previous crop.
Zero till crops generally require more starter N than conventionally planted crops due to N tie-up in the
mulch.
11
Research in the NT has shown that a legume pasture phase can contribute between 42.0 and 136.0 kg/ha of
N, depending on length of pasture phase, soil type, pasture use and seasonal conditions. Growing legumes
in rotation will help reduce N fertiliser requirement. A soil analysis should be conducted to ascertain N
content and determine how much fertiliser is required to meet target yield. Leaching of N in sandy soils can
be very high (over 80.0 kg/ha) over the wet season, so this needs to be considered when calculating fertiliser
rates for irrigated dry season crops on light soils.
Figure 7. N deficiency (light stunted plants) due to uneven application of fertiliser
PHOSPHORUS (P)
P is often the second most limiting nutrient in Top End soils. P is active in plant cells and assists in chemical
and energy transfer within the plant. It is critical for early crop development and growth, because young
plants have a higher requirement for P than older plants. A 10.0 t/ha grain crop will take up between 40.0
and 50.0 kg/ha of P and will have taken up 30% of this prior to tasselling. While P is taken up continuously, a
deficiency will show up before the crop is about 65 cm tall.
Maize grown on light soils often shows an early P deficiency unless the crop has been banded with a P
based fertiliser. Banding fertiliser close to the seed is more efficient as it reduces soil P fixation and allows
the plants to pick up nutrients immediately after germination. As P does not leach, all of the phosphorus can
be applied prior to planting. Phosphorus deficient plants are darkish green with purple colouration on the leaf
edge and on the stems. Crops suffering from phosphorus deficiency are slow to develop and will have
delayed silking.
POTASSIUM (K)
K is taken up in quantities second only to that of N. A 10.0 t/ha maize crop (grain and stover) will take up
over 200.0 kg/ha of K. Light sandy soils such as Blain and Ooloo have low levels of exchangeable K and will
require some K fertiliser. K is important for circulation of sugars, cell division and aids in diseases resistance.
It also regulates water control in the plant which is critical for healthy crop growth.
Maize will have taken up 50% of its K requirement by week 8 and 75% by silking (week 9 to 10). The rate of
uptake increases rapidly in the three weeks prior to silking so adequate K must be available during this
period. K deficiency symptoms are usually seen on the lower leaves which have yellow-necrotic (dead)
edges.
12
SULPHUR (S) AND MAGNESIUM (MG)
S and Mg are secondary nutrients and are taken up in relatively large quantities, although less than N, P and
K. S is an essential part of plant proteins and is a constituent of many amino acids, vitamins and enzymes. S
requirement is usually addressed when applying super-phosphate or other blended fertilisers. Much of the S
is derived from organic matter in the soil and mineralised S forms. An S deficiency will also appear as pale
green to yellow foliage similar to that of an N deficiency.
Mg deficiencies are generally infrequent in dryland crops but high yielding irrigated maize crops will take up
5.0 kg to 6.0 kg of Mg per tonne of grain. Mg can be applied as dolomite or in magnesium sulphate fertilisers.
TRACE ELEMENTS
Trace element deficiencies are common on light textured alkaline soils in the NT. Maize is susceptible to Zn
deficiency and most NT soils will require Zn prior to intensive cropping. Zn Cu, B, iron (Fe), manganese (Mn)
and Mo are essential for optimum growth but are required in minute quantities. For example, maize requires
about 16.0 kg to 19.0 kg of N per tonne of grain but only 10.0 g to 20.0 g of Zn per tonne.
High-yielding irrigated crops will require trace element application to compensate for low soil levels. Most
trace elements can be blended with basal NPK fertilisers and banded below the seed. Trace elements can
also be applied through the irrigation water either prior to planting or during the growing phase.
Applications of 5.0 to 10.0 kg/ha of Zn as zinc-sulphate, every two years will build soil zinc levels. Applying
Zn (1.0 to 2.0 kg/ha as zinc-sulphate heptahydrate) and N through the irrigation water during the vegetative
and prior to silking will assist in preventing deficiencies. This can be avoided by banding ‘start-up’ fertiliser
containing N, P and Zn beneath the seed.
Figures 8 and 9. Early nutrient deficiency in young maize on sandy surfaced soils
NUTRIENT AVAILABILITY AND SOIL PH
Soil pH affects the availability of many plant nutrients. The natural soil pH of red earths varies from slightly
acid to neutral (pH 6.0 to 7.0). However pH can vary with depth and may change due to management,
fertiliser history and water application. Most of the essential nutrients are readily available over pH 6.0 to 7.0,
but many trace elements are “tied up” when soil pH increases.
Many bores in the Top End are high in Ca and Mg carbonates and high in pH. Continuous irrigation with high
pH water increases soil alkalinity and can induce Zn, Fe, Cu, Mn and to a lesser degree B deficiencies. This
13
effect is referred to as lime induced chlorosis when Zn and Fe deficiency causes yellow striping between the
leaf veins. Light soils have low buffering capacities and are particularly susceptible to increasing soil pH
under irrigation. On a light soil in Katherine, pH increased from 6.5 to 8.5, which induced Fe and Zn
deficiencies resulting in a substantial yield reduction in both sorghum and soybeans.
Applying acidifying fertilisers such as ammonium sulphate, mono-ammonium or di-ammonium phosphates

will assist to counter the rise in pH. Monitoring soil pH will assist in nutrient management.
TIMING AND APPLICATION OF CROP NUTRIENTS
The correct timing of nutrient application is critical in achieving optimum growth and yields. Maize takes up
nutrients even before the seedlings emerge. A large proportion of the crop’s requirements should be applied
before planting to ensure nutrients are available when needed. By week 10 (70 days after sowing) maize will
have taken up over 80%, 53% and 88% of its N, P and K requirement, respectively. It will continue to take up
N and P after silking.
All of the P, K, S and trace elements can be applied prior to planting. N is best applied as split applications.
Applying two thirds of the crops N requirement at planting and the remainder two weeks before silking is
recommended. Early research at Katherine Research Station found that 120.0 kg/ha of N, pre-plant and 60.0
kg/ha of N at both 35 and 70 days after sowing gave the highest maize yields on a Tippera clay loam. N
fertiliser is easily applied in the irrigation water when required.
Fertiliser should not be placed in contact with the seed as maize is sensitive to fertiliser burn, especially on
light soils. Only about 5.0 kg/ha of N and 10.0 kg/ha of P should be placed with the seed. Banding fertiliser
beneath and to the side (Figure 10) is the safest and most efficient option. Banding allows higher rates to
be applied and ensures an immediate supply of nutrients, promoting vigorous establishment and growth. All
the P, S, trace elements and some N can be banded at planting. K can be broadcast and incorporated prior
to planting. Urea, if used as a pre-plant fertiliser, must be incorporated into the soil either by cultivation or
irrigation to prevent loss to the atmosphere. The balance of the N fertiliser can be applied as one or more
applications in the irrigation water prior to silking.
From about 21 days after sowing (DAS), maize grows rapidly and takes up nutrients in increasing amounts.
At about 42 DAS when there are 12 fully formed leaves, the number of seeds (ovules) and the eventual size
of the ear are determined.
The most critical period in terms of yield potential for maize occurs from about two weeks before silking
(46 to 49 DAS) to about two weeks after silking (77 DAS). A larger reduction in yield will result from
moisture and nutrient stress at this time than at any other period. Ensuring all nutrients are in adequate
supply during this critical period will help achieve maximum yield potential.
14
Soil Surface
3.0-4.0 cm
5.5 cm
2.5cm
Maize Seed
Fertiliser granule
Figure 10. Schematic plan of fertiliser placement in relation to seed
FERTIGATION
Fertigation is the practice of applying soluble fertilisers through the irrigation water. It is an efficient way of
applying many nutrients, particularly N. Maize in particular is suited to fertigation due to its tall stature and
high demand for nutrients. The advantage of fertigation is that nutrients are applied at the appropriate time
and level to maximise plant growth, reduce nutrient loss and avoid traffic over the crop.
Fertigation is an ideal way to split N applications and apply trace elements. Urea and ammonium sulphate
are highly soluble fertilisers and can be dissolved with other nutrient such as Zn and B and applied at any
time through the crop growth cycle.
Chemical and/or fertiliser injection systems shall not be installed into bore discharge lines without
prior approval from the Controller of Water Resources.
Figure 11. Fertigation tank for applying nutrients in the irrigation water
15
Table 3. Nutrient uptake by maize crop (kg/ha)
Yield (t/ha) N P K S Mg
Grain 5.0 80 17 22 8 10
Stover 5 to 6 56 9 90 10 19
Total DM* 11.0 136 26 112 18 29
Silage 32 (wet)
Grain 10.0 160 32 41 15 17
Stover 10 to 11 112 14 166 17 35
Total DM* 20.8 272 46 207 32 52
Silage 60 (wet)
Grain 12.5 200 39 51 18 20
Stover 12 to 13 140 16 194 20 38
Total DM* 24 340 55 245 38 58
Silage 75 (wet)
Table adapted from Pacific Seeds: Hybrid Corn Production Agronomy Guide 2006/7 (10% grain protein)
* Total DM (dry matter) refers to the combined dry matter yield of the grain and stover. Silage removes an
equivalent amount of nutrients. Silage is usually harvested at 60 to 65% moisture resulting in high yields of
forage/ha.
Key points:
• Maize has a high nutritional requirement
• The period from week six to week ten is the most

critical time in terms of nutrient requirement and yield
determination
• Fertiliser inputs need to be balanced with soil fertility

and yield expectation
• Optimum N and plant population are the keys to high

yields.
DISEASE AND INSECT CONTROL
Disease in maize in the NT is of relatively low importance compared to insect problems. This is in part due to
the small areas in which maize is grown, but is mainly due to disease resistance of modern varieties.
Nevertheless, there are several serious plant diseases which attack maize in the tropics because the
environment encourages the growth and spread of plant pathogens. There are root, stalk and ear rots which
can potentially cause economic damage to maize. However, foliar diseases such as leaf blights, spots and
rusts are the most damaging in tropical environments.
Seed rots and seedling blights are usually caused by waterlogging or cool damp soil conditions. The main
fungi which cause these diseases include Pythium, Diplodia and Fusarium species. These diseases are
largely controlled by fungicidal seed dressing and good agronomic management.
16
Drought, waterlogging, late rain at maturity and nutrient stress predispose crops to disease. Irrigated dry
season maize should not be subjected to these conditions so as to minimise disease. Planting the best
disease-resistant varieties, adopting good agronomic management and controlling insect pests will minimise
the incidence of disease.
Insect pests multiply and develop faster in the tropical Top End than in southern environments because of
higher temperatures and humidity. As such, the management of insects and diseases should be a high
priority. An insect management plan should be in place before planting. The plan should consider potential
pests, beneficial insects, appropriate chemicals, pest control and application options.
SOIL INSECTS
Soil insects can cause up to 30 % plant loss and are potentially more damaging than pests which attack
aerial parts. Soil insects are harder to detect and damage may only be seen as poor plant establishment.
When damage is severe, re-planting is sometimes the only option.
There is a range of soil insects that attack maize seed and seedlings including black field earwigs, false
wireworms, cutworms and wireworms. These insects damage germinating seeds and seedlings by
chewing young roots and shoots below or on the surface of the soil.
The occurrence of soil pests may increase under minimum and zero-tillage practices because of a more
favourable environment for both insects as well as plants. The absence of tillage and the maintenance of
mulch results in fewer insects being killed and desiccated, increasing the potential for damage in
conservation farming. However, a number of control options are available including insecticidal grain baits,
in-furrow chemical applications, or seed treatments.
Developments in systemic insecticidal seed treatments have greatly improved the control of soil-borne
insects and other pests such as mites, aphids and leafhoppers, which attack young crops. New seed
treatments protect the seed and seedling for several weeks, allowing the plant to develop without damage.
Gaucho® (imidicloroprid), Cruiser® (thiamethoxam) and other registered seed treatments are recommended
for the control of soil pests and some above-ground insects. There are several advantages to seed
treatment. The crop is protected from the time it is planted, chemical use is greatly reduced as it acts
specifically on pest insects and the treatment eliminates the need for handling and applying pesticides for
soil insects.
High quality treated seed is available from most reputable seed companies. Some market their products
under specific brands such as Elite® (Pacific Seeds) and Betta Strike® (Pioneer Brand Seeds), to distinguish
their highest quality seed. Seed treatment should be carried out under strict guidelines set down by chemical
manufacturers to ensure quality, consistency and efficacy.
OTHER MAJOR PESTS
Leafhoppers are a serious economic threat to irrigated maize in the Top End if not controlled. Leafhoppers
are one of the largest families of plant-feeding insects and are endemic in the Top End. They have piercing
sucking mouthparts and feed on plant sap. The species which attacks maize (Cicadulina bimaculata)
transmits wallaby ear virus (WEV).
WEV stunts maize plants and can reduce yields by over half. Leaves are characterised by having erect
growth with pronounced veins. In severe cases, the crop may have to be ploughed out. Prior to the
development of insecticidal seed treatments, the only option was to spray the insects. Several applications
were often necessary. However, control of leafhopper can now be achieved with systemic insecticidal seed
treatments such as Gaucho®.
17
Armyworms, heliothis (Helicoverpa spp.) and the green vegetable bug (GVB) can cause significant damage
to irrigated maize, especially when they occur at the same time. Chemical control may be required in some
seasons when pests reach damaging levels. Other insects include the corn aphid, mites, cutworms and
various beetles, but these have not been of economic importance in the NT up to now.
Armyworms usually occur mid season when the crop is still vegetative. They feed in the whorl of the plant on
emerging leaves, and it can be difficult for insecticides to reach them. Large maize plants can sustain
considerable leaf damage before control is required. Armyworms can strip leaves back to the mid-rib and
may have to be controlled if damage occurs to the tassels. Armyworms are best controlled in conjunction
with other pests, such as heliothis and GVB.
Heliothis caterpillars usually invade the crop at silking. Moths lay pin-head sized white eggs on the silks and
tassels. As the larvae grow, they feed on the tops of the young ears and work their way into the sheath,
feeding on immature grain. Heliothis are generally more damaging than armyworms because they feed
directly on the silks and immature grain. Priority should be given to controlling heliothis if there are more than
two small larvae per cob. Caterpillars need to be controlled before they become too large. The ideal target
size for control is when caterpillars are 3 mm to 7mm long.
GVB can be an economic pest of irrigated maize in some seasons. When wet season Cavalcade (legume
hay) crops are harvested, GVB migrate into maize and other irrigated crops. GVB adults and nymphs feed
on immature grain by piercing the seed with their proboscis (sucking mouth tube). When in large numbers,
GVB distort the ears and prevent the grains from maturing.
Figure 12. Potato leafhopper adult and nymph, similar to the maize leafhopper
Photo by: Steve L. Brown, University of Georgia, www.forestryimages.org
18
Figure 13. Effects of WEV Figure 14. Healthy plants on left and stunted plants
on right, affected by WEV
Figure 15. Heliothis caterpillar
19
Figure 16. Green vegetable bug and eggs on maize
Figure 17. Northern armyworm damage Figure 18. Heliothis (left) attacking ear and armyworm
feeding on leaf
20
Figure 19. Trichogramma wasp parasite on heliothis Figure 20. Spider predating an insect
egg (Photo, Brad Schultz, QDPIF)
Figure 21. Assassin bugs feed on caterpillars Figure 22. Ladybirds feed on aphids and other soft
pests
CHEMIGATION FOR PEST CONTROL
Chemigation is the application of pesticides (insecticides, fungicides, herbicides etc) through irrigation water.
A chemigator is a purpose-built device which accurately measures and injects the desired amount of
pesticide through irrigation water on to the crop. It consists of a chemical tank and a precision pump, which is
preset to a required dose per hectare. It has valves to prevent backflow and contamination of water supplies.
Chemigation is an effective way of applying certain pesticides and eliminates the need for expensive aircraft
application. It allows the application of pesticides when insects are at an optimum size, thereby maximising
21
control and minimising pesticide use. It also allows the use of ‘softer’ control options (biological insecticides
such as Gemstar®) which target pests such as heliothis while minimising the impact on beneficial insects. In
areas where aerial application is not an option, chemigation is probably the only effective late-season pest
management option in maize.
The installation of chemigation units must meet relevant environmental (water authority and pesticide-
use) legislation. Issues such as drift and volatilisation of chemicals must be managed appropriately.
Legislation regarding chemical use and application methods changes from time to time. Therefore it is the
responsibility of the operator to check local legislative requirements and label recommendations before
applying any pesticide through an irrigation system.
Chemical and/or fertiliser injection systems in the NT shall not be installed into bore discharge lines
without prior approval from the Controller of Water Resources.
Figure 23. Chemigation unit used for applying pesticides through irrigation water
CROP SCOUTING
Crop scouting is essential for effective insect management and is required to identify the presence and size
of both pests and beneficial insects. There is a range of predatory and parasitic insects which reduce pest
numbers. Spiders, lacewings, ladybugs, shield bugs and predatory wasps play a role in regulating pest
populations. In some seasons pests are controlled by beneficial insects without the need for chemicals. It is
also important to detect pests before they become too large as small immature insects are easier to control
and require less pesticide.
22
Scouting needs to be carried out every week and up to three times per week at silking and early grain fill.
Silking is the most susceptible period because damage to silks reduces pollination and seed set. It is
necessary to walk through the crop and inspect leaves, ears, silks and tassels at several locations.
The presence of insects does not necessarily mean the crop requires spraying. Insect numbers need to be
sufficiently high and at a critical or threshold level (i.e. approaching economic damage) before spraying is
warranted. The threshold level for specific pests is hard to determine at times as injury will depend on stage
of crop growth and the presence or absence of other pests and beneficial insects. Developing experience
with insect identification and damage is necessary. Assistance with insect management can be sought from
a consultant, entomologist or Departmental agronomist.
Figure 24. Insect scouting is an essential part of pest management in cropping systems
INTEGRATED PEST MANAGEMENT (IPM)
IPM is a strategy of pest management which uses a combination of biological, cultural and chemical
methods to keep pests below economic injury levels, while reducing pesticide use and its impact on the
natural environment. IPM includes selecting the best adapted varieties with resistance to insect and
diseases, using protective seed dressings, planting optimum populations in narrow rows for weed
suppression and monitoring the crop closely for pest and beneficial insects.
Using biological insecticides (Gemstar®) and pheromone traps to monitor pest populations (i.e. heliothis
moths), and spraying only when pest levels approach economic injury level will assist in more efficient pest
management. Relying on several integrated practices to control pests will give better results and improve
overall crop performance.
23
Table 4. Insect pests of irrigated maize in the NT
Insect pest Growth period and damage Comment and control

Soil insects: From planting until full Commonly used methods of control include
wireworm, (click beetles) emergence. Insects chew insecticidal grain baits for control of adults,
(Family Elateridae) young roots, shoots and can seed treatment and in-furrow spraying for
prevent germination of seeds control of larvae (and adults in some cases).
and reduce establishment in
severe infestations. Germinating grain bait technique
Soil insects can dramatically Soak insecticide-free crop seed in water for
reduce plant populations if in at least 2 hours to initiate germination.
False wireworm, (pie dish)
high numbers. To detect them
(Gonocephalum spp., Bury a small handful of the seed at shallow
in the soil, grain baits are used
Pterohelaeus spp.), depth and cover it lightly with 1 cm soil
to estimate numbers prior to
planting.
Choose five widely spaced sites in each 100
For more information on ha; at each site, bury seed on the corners of
control of specific soil insects, a 5 m x 5 m square.
see QDPI&F publication
Check for seedling emergence - once
"Managing insects & mites in
emerged, leave seedlings overnight.
field crops, forage crops and
Earwigs(Nala lividipes) pastures; Information Series Dig up the entire plants the next day and put
QI92004." the plants on a tray to count insects.
If there are one or more insects (or five

earwigs) per bait, then control is required.
Leaf hoppers (various) From emergence through to Seed treatment with a protective systemic
Cicadulina bimaculata week 5 or 6. Causes wallaby insecticide (Gaucho®). Spraying insects one
possibly Chiasmus sp. and ear i.e. stunting and distortion to two weeks after crop emergence is less
Orosius sp. and thickening of leaf and effective.
veins.
See text for damage caused.
Armyworms (Mythimna Late vegetative stage to Monitor population and natural biological
separata) silking. Defoliate plants and agents. Apply registered insecticide or
can damage flag leaf and silks. biocide.
Green vegetable bug Heavy infestations cause Monitor population and predation. Apply
(Nezara viridula) distortion of cobs and damage registered chemical when required. Time
to individual kernels. application to control other pests if possible.
Heliothis (Helicoverpa Damage to silks and cobs. Monitor presence and population. Apply
armigera/punctigera) registered insecticide or biocide and apply at
appropriate growth stage.
Adapted from QDPI&F Summer Crop Management Notes 2005
24
Table 5. Insecticides registered for use in maize
Pest Insecticide Trade name examples Withholding period in days

(active
Grain Grazing
ingredient)
Armyworm chlorpyrifos Lorsban 10 2
methomyl Lannate L, Marlin 14 14
trichlorfon Dipterex 2 2
Heliothis Gemstar Nuclear polyhedrosis ns ns
virus
alpha-cypermethrin Dormex 7 ns
methomyl Lannate L, Marlin 14 14
cypermethrin Cypermethrin 200 7 ns
deltamethrin Ballistic ULV 7 ns
thiodicarb Larvin 375 7 7
Green vegetable deltamethrin Ballistic ULV 7 ns
bug
Cutworm chlorpyrifos Lorsban 10 2
Wireworm, other chlorpyrifos Lorsban in furrow spray 10 2
soil insects or grain bait
terbufos Counter 150 g granular ns ns
insecticide/nematicide
Seed dressing Seed dressing with
Gaucho® Cruiser®
Maize dimethoate Rogor® 28 1
Leafhopper* Seed dressing Seed dressing with
Gaucho® or similar
systemic insecticides.
Adapted from QDPI&F Summer Crop Management Notes 2005 and APVMA web site: [email protected] (ns = not
specified)
• Gaucho is registered for soil and sucking pests in maize but also controls leafhoppers which transmit WEV.
• Always refer to the APVMA site for current registrations, products and labels as details may be subject to
change and withholding periods can vary between crops. The use of a trade name as an example is not an
exclusive recommendation of that product.
PESTICIDE USE AND CHEMICAL REGISTRATION
Due to continual changes in pesticide technology, use and legislation it is imperative to keep up to date with
new developments and requirements. There are a number of databases which contain information on
agricultural and veterinary chemicals. The Agricultural Pesticides and Veterinary Medicines Authority
(APVMA) is an Australian government authority responsible for the assessment and registration of
pesticides and veterinary medicines. It administers the National Registration Scheme for Agricultural and
Veterinary Chemicals (NRS) in partnership with the States and Territories. The web site is
www.apvma.gov.au The APVMA database is linked to the Infopest database which is operated by the
Queensland Department of Primary Industry and Fisheries.
Infopest is a computerised database of all nationally registered agricultural and veterinary chemical products.
It is available on CD ROM and is currently being developed for the web. The CD is produced by and
available from QDPI&F GPO Box 46, Brisbane, Qld. 4001, email [email protected]
25
Key points:
• Have a pest management plan prior to planting
• Buy seed treated with a systemic insecticide for

leafhopper and soil insect protection
• Scout crop regularly to determine pest level,

damage and beneficial insects
• Have ready access to suitable control measures
• Use the correct/registered chemical at the optimum

time and consult national databases.
WEED CONTROL IN MAIZE
Weeds compete for light, water and nutrients and can dramatically reduce yields. The type of crop and mulch
level which precedes maize will determine the cultivation method, land preparation, sowing technique and
weed control strategy. Weeds can either be managed by herbicides, cultivation or a combination of both.
Herbicides combined with conservation tillage are an integral part of modern farming. Herbicides offer
greater flexibility and more options for weed control. Conservation farming allows for timely planting and
eliminates the need for cultivation. Continuous cultivation consumes considerable energy and leads to a
decline in soil structure, a depletion of organic matter and predisposes the land to erosion. Soil conservation
and organic matter preservation is a high priority in NT farming systems.
Conventional tillage systems use a combination of cultivation and herbicides to control weeds. Once weeds
are killed with cultivation, the crop is planted into a clean seedbed. Pre-emergent, soil residual herbicides
such as metolachlor (Dual®), pendimethalin (Stomp®), flumetulam (Broadstrike®), propachlor (Ramrod®),
atrazine (Nu Trazine®, Gesaprim®, Atrazine®) can then be applied immediately after planting to control
broadleaf and grass weeds. The choice of herbicide will depend on the weed spectrum. In many cases two
herbicides will be used in combination to give a broader spectrum of control. An irrigation of 6.0 mm to 10.0
mm immediately after application will incorporate and activate the chemical while enhancing crop
germination. The combination of metolachlor and atrazine in a commercial product (Primextra®) provided
excellent weed control in maize trials at DDRF.
Inter-row cultivation or inter-row spraying with post-emergent herbicides such as picloram, 2,4-DB, dicamba,
fluroxypyr are other options for in-crop weed control in conventional tillage systems. Post-emergent
herbicides need to be applied at the correct crop and weed growth stages to prevent crop damage and
achieve optimum weed control. There are specific restrictions and application procedures which need to be
followed for each chemical. Inter-row cultivation also needs to be undertaken early to prevent damage to the
roots and the crop. Using narrow row spacing (75 cm) also results in quicker canopy closure, better weed
suppression and can, in some cases, enhance yield.
In minimum or zero-tillage systems (also called conservation tillage) crops are sown with minimum soil
disturbance and herbicides replace cultivation as the primary means of weed control. Glyphosate is the
principal knock-down herbicide in conservation tillage and one or two applications may be required to ensure
all emerged weeds are controlled before planting. Glyphosate may be mixed with other herbicides to
26
increase the spectrum of control. Once the crop is planted, post emergent herbicides are usually necessary
for extended weed control. The choice of herbicide combination will depend on the weed spectrum.
Mulch management is a major consideration in conservation farming. Excessive mulch levels will interfere
with the efficacy of herbicides and cause blockages at planting. Mulch “ties up” soil applied herbicides and
nitrogen, especially when partially broken down. Managing mulch levels to allow ease of planting, maximise
weed control and crop nutrition is critical to the success of conservation farming systems.
A relatively recent development in weed control in maize (and many other crops) is the introduction of the
CLEARFIELD® production system. Clearfield Technology is a system of weed management which
combines the use of imidazolinone-tolerant maize varieties and commercially-formulated herbicides. Maize
varieties have been developed which are tolerant to imidazolinone herbicides. These are highly active
residual herbicides which provide effective and extended control of many perennial grasses, broadleaves
and nutgrass. Lightning® (imazethapyr + imazapyr), is the herbicide specifically registered for use in the
Clearfield® system. The system is ideal for conservation tillage systems where broad spectrum, post-
emergent weed control is required.
Figure 25. Conventionally tilled maize with pre-emergent herbicide showing excellent weed control
27
Figure 26. Row sweepers on a conservation tillage planter, which “sweep” the row clean of mulch to allow
the seed to be planted without obstruction
WEEDS OF SIGNIFICANCE
The major weeds in irrigated maize crops include summer grasses (Brachiaria, Digitaria sp.), crowsfoot
grass (Eleusine indica), Pennisetum sp. and barnyard grass (Echinochloa colona). Grasses compete
strongly for water and nitrogen and will reduce yields if unmanaged. Grasses are best controlled with pre-
emergent herbicides such as atrazine and metolachlor formulations i.e. Atrazine®, Dual® or Primextra® or
by using Lightning® with varieties with the Clearfield Technology®. Inter-row spraying with shielded sprayers
or cultivation is also an option.
Major broadleaf weeds include caltrop (Tribulus terrestris), senna (Senna obtusifolia) and Sida sp., Hyptis,
nutgrass (Cyperus rotundus) and pigweed (Portulaca sp. and Trianthema sp.) A number of herbicides
(atrazine, Starane®, Tordon 75-D® etc) are effective in controlling a range of broadleaves post-emergent.
The timing of post-emergent herbicides is critical to achieve effective weed control and to prevent crop
damage. Applying certain herbicides (2,4-D, dicamba) past a specific growth stage will result in permanent
crop damage and significant yield reduction. Follow recommendations on timing of herbicide application to
avoid crop injury.
Weed spectrum and weed dynamics are likely to change depending on farming practice, herbicides used
and rotations. Minor weeds may become economically significant over time and some weeds may develop
herbicide resistance. Rotating crops, herbicides and cultivation practice to manage herbicide resistance is a
major challenge and should be a high priority in farming systems in the NT.
Table 6. Herbicides registered for post-sowing, pre-emergence weed control in maize
Chemical atrazine pendimethalin s-metolachlor s-metolachlor flumetsulam propachlor linuron

+ atrazine
Trade Gesaprim Stomp Dual Gold Primextra Broadstrike Ramrod Linurex
name Gold
Adapted from QDPI&F Summer Crop Management Notes 2005
28
Table 7. Common herbicides registered for post-emergence broadleaf weed control in maize
Chemical atrazine + atrazine + atrazine + picloram picloram+ fluroxypyr dicamba mcpa imazethapyr + flumetsulam
wetter picloram fluroxypyr 2,4-DB imazapyr (see notes)
(add wetter) amine
Trade Gesaprim Gesaprim Gesaprim Tordon Tordon 75D Starane Dicamba MCPA Lightning Broadstrike
name and other + Tordon Starane 75-D + Amicide 500 250
products 75-D and other 625
products
Notes: Lightning Herbicide must only be applied to maize varieties with CLEARFIELD® Technology
Adapted from QDPI&F Summer Crop Management Notes 2005 and APVMA web site: [email protected]
Always refer to the container label for current registration and safety information. These details may
be subject to change. Withholding periods can vary between crops. Check container labels for
details.
Current national information on agricultural chemicals registered for use in maize is available on the
Infopest CD-ROM. Write to GPO Box 46, Brisbane, Qld. 4001, email [email protected]
Key points:
• Control weeds early and sow crop into a moist,

weed-free seedbed
• Use correct herbicide and rate for weed spectrum

and soil type
• Use optimum nutrition, plant population and

narrow rows to suppress weeds
• Weed spectrum will change and resistance to

herbicides will become more prevalent
• Be prepared to rotate herbicides and adapt

management.
IRRIGATION MANAGEMENT
The arable red earths of the Top End are suited to sprinkler systems (centre pivot/lateral move etc) due to
their high infiltration rates (up to 180 mm/hour initially), low water-holding capacities and deep percolation.
Flood irrigation on these soils results in erratic wetting and poor water distribution, causing unsustainable
water loss due to deep drainage through the profile. There are several areas of black and grey clay soils in
the NT which are suitable for flood irrigation. However, these are largely undeveloped for agriculture.
Irrigated maize will be produced predominantly on the lighter soils under sprinkler systems until such time as
the heavier soils are developed for agriculture.
An irrigated maize crop in the dry season will require between 5.0 and 7.0 ML/ha of water, depending on
planting time, cultivar, soil type, seasonal conditions and irrigation efficiency. This equates to 500 mm to 700
mm of water applied through the growing season.
29
A crop sown in March will require less water than that sown in May because of lower evaporative demand in
the earlier planted crop. Maize takes approximately 100 to 120 days to reach physiological maturity
depending on variety and will usually require about 100 days of irrigation. Underestimating water demand will
stress the crop and reduce yield, while overestimating water demand results in nutrient leaching, water
logging and a waste of water and money. The full potential of maize will only be achieved when it is grown
without stress throughout the season.
USING A WATER BALANCE APPROACH TO SCHEDULE IRRIGATION
Irrigation scheduling is the process of calculating the timing and volume of water required to meet crop
demand and yield expectations. The simplest method to schedule irrigation is to calculate crop water
requirement using a water balance technique similar to a check-book (i.e. with debits and credits). This
method calculates water losses through evapo-transpiration and gains through irrigation and rainfall.
To use a water balance approach the following information is needed:
• Soil water-holding capacity and starting soil moisture.

• Daily evaporation rates.
• Effective crop root zone.
• Allowable soil moisture depletion.
Soil water-holding capacities for different soil types are usually provided by agriculture and natural resource
agencies. Estimates of plant water use are commonly obtained using evaporation (referred to as pan
evaporation) figures from a specifically designed US Class A evaporative pan. Pan evaporation
measurements are recorded in mm of evaporation per day by weather stations and departments of
agriculture. Douglas Daly Research Farm records daily evaporation.
Crop water demand is driven by temperature, humidity, solar radiation and wind speed. The combined
evaporation from soil and transpiration from leaf surfaces is termed evapo-transpiration. High
temperatures, clear sunny days and strong wind will cause high evapo-transpiration and thus a high crop
water requirement.
Evaporation from a Class A pan closely approximates the evaporation rate from a reference crop. The
reference crop usually refers to a well-watered, full-canopy grass sward. The daily evaporation figures are
then used in conjunction with a crop factor to estimate daily crop water use. A crop factor is a fraction or
ratio which estimates the difference between pan evaporation and the actual crop evapo-transpiration.
Young crops with a small leaf surface area use only a fraction of the daily pan evaporation rate and therefore
have low crop factors (i.e. 0.2 to 0.5), reflecting low water use. A mature or fully vegetative crop will be
assigned a higher crop factor (i.e. 0.9 to 1.1), to reflect higher water use. Crop factors of 1.0 or higher
indicate that evapo-transpiration (crop water demand) is now equal to or greater than the daily pan
evaporation. Water requirement can be estimated by:
Crop water requirement (mm) = Pan evaporation (mm) x crop factor (evapo-transpiration)
Example:
Pan evaporation per week = 49 mm (i.e. 7.0 mm/day)

Crop factor for maize not at full canopy = 0.7
Water requirement is 49 mm x 0.7 = 34.3 mm/week.
30
Crop water use will vary from week to week in line with variations in the weather. Evaporation rates can
range from 5.0 mm to over 10 mm/day in September to November (Figure 23). When scheduling irrigation,
take into account the variation in daily evaporation rates. The use of an average weekly evaporation figure
can result in over or under estimating water demand. Tabulating daily evaporation is necessary to determine
weekly crop use and to calculate the amount of water that needs to be replaced at the next irrigation.
Average evaporation rates in September to November appear moderate but daily temperatures are generally
over 36°C. Evaporation rates range from 6.0 to almost 12.0 mm/day in the Katherine-Daly Basin. In contrast,
temperatures from May to August are usually 33°C or less, with an evaporation range of 4.0 to 9.0 mm/day.
One of the major considerations for irrigated crop production is the total number of days with temperatures
over 35°C later in the dry season. From September to November, 23 days per month on average will have
temperatures of 35°C or higher, which is above the optimum temperature range for maize production (25 to
32°C).
The Bureau of Meteorology provides comprehensive data on climatic characteristics for a number of
locations in the NT.
Table 8. Crop factors for maize at different stages of growth
Days from Ave crop factor Physiology of the crop Comment

planting for the period
5 to 15 0.23 Early seedling growth, small Low moisture requirement
leaves
15 to 25 0.30 Increasing leaf and root Increasing water demand and growth
extension
25 to 40 0.5 Initiation of tassel and rapid Rapid leaf and root growth and
leaf expansion. Initiating grain increased water demand
numbers
40 to 60 1.0 Formation of ear and Full canopy cover and approaching
tasselling maximum water use
60 to 95 1.1 Silking, fertilisation and early Peak water demand and maximum
grain fill shoot and root development.
Stress at this time will have more
impact on yield than at any other
time in the crop’s life
95 to 110 0.9 Grain filling and maturation High water demand to fill grain
110 to 120 0.5-0.35 Late grain fill Water requirement declining as grain
reaches maximum dry matter
Figures adapted from FAO Irrigation and Drainage Paper 56
31
Evapo ration figu res in m m /d ay fo r 1998
14
12
10
Evaporation in m m /d
Daily evaporation
4 can vary from 5 mm to almost 12
mm/day within a few days.
2
0
9 8 98 98 98 98 98 98 98 98 98 98 98 98 98 98 98 98 98
19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19
0 3/ 0 3/ 0 3/ 0 4/ 0 4/ 0 5/ 0 5/ 0 6/ 0 6/ 0 7/ 0 7/ 0 8/ 0 8/ 0 8/ 0 9/ 0 9/ 1 0/ 1 0/
0 1/ 1 5/ 2 9/ 1 2/ 2 6/ 1 0/ 2 4/ 0 7/ 2 1/ 0 5/ 1 9/ 0 2/ 1 6/ 3 0/ 1 3/ 2 7/ 1 1/ 2 5/
D AT E
Figure 27. Daily evaporation rates (mm/day) from March to October 1998 at DDRF
Table 9. Average monthly evaporation at Douglas Daly Research Farm latitude 13°50'04"S, longitude
131°11'14"E, elevation 42.8 m
Month Average daily pan Average daily maximum Average monthly

evaporation (mm) temperature (ºC) evaporation (mm)
January 5.7 33.8 175.2
February 4.7 32.9 145.4
March 5.5 33.7 170
April 6.0 34.5 181
May 6.4 33.0 199
June 6.2 31.5 185
July 6.4 31.7 199
August 7.2 33.6 223
September 7.6 36.5 227
October 7.6 36.6 235
November 6.8 36.7 204
December 6.1 34.7 188
Data: Climate and Consultancy Section, Northern Territory Regional Office of the Bureau of Meteorology, 27 July 2004
Start of records 1/8/1968
32
Table 10. Estimated soil-moisture availability for different soils in the Top End
Soil type Plant avail. water- moisture Allowable deficit Readily available water/m
holding capacity/m (allowable depletion (50%of total water
(difference between field before irrigation) available)
capacity* and wilting point**)
Blain (sandy loam) 40 to 75 mm 40 to 50% 20 to 35 mm
Oolloo 60 to 80 mm 40 to 50% 30 to 40 mm
Tippera (clay loam) 75 to 140 mm 40 to 50% 37 to 70 mm
Note: *Field capacity = drained upper limit **Wilting point = drained lower limit. Field capacity is amount of water held in
the root zone after the soil has been saturated and allowed to drain for 24 to 48 hours. Data adapted from Dilshad et. al.
1996.
The effective rooting depth for maize is over 1.5 m. However, irrigating to 70.0 to 80.0 cm is sufficient using
sprinkler irrigation in the NT, as most of the moisture will be taken up from within this zone. The allowable
soil moisture depletion is usually set at 40% to 50% in line with good irrigation practice. Drying the soil down
to more than 50% depletion increases the risk of stress and yield reduction, especially if it suddenly turns hot
or if a problem develops with the irrigation system.
When maize reaches full canopy closure (i.e. crop factor 1.0) in June/July it will require on average 35.0 mm
to 45.0 mm of irrigation water per week, depending on location and environmental conditions. This could
increase to about 70.0 mm per week in October for late crops. Applying such quantities of water by sprinkler
irrigation (centre pivot or lateral move) will usually require two to three irrigations per week at peak times.
Large irrigations (i.e. over 30.0 mm at one time) on the red earths can cause temporary ponding, runoff and
deep drainage. Applying two small, rather than one large application will reduce water losses and improve
water-use efficiency.
USING SOIL MOISTURE SENSORS TO SCHEDULE IRRIGATION
There is a wide range of sensors that directly or indirectly measure soil moisture. These vary in price from a
few hundred dollars (i.e. tensiometers) to sophisticated electronic sensors costing several thousand dollars
(i.e. capacitance probes). Tensiometers are the simplest and most economical soil moisture sensors.
Tensiometers are porous ceramic tipped tubes fitted with a vacuum gauge. They measure the tension with
which moisture is held in the soil. Upon drying, the soil moisture tension increases so that water is “pulled”
from the tensiometer into the soil creating a vacuum which is registered on the gauge. The reading will
indicate when irrigation is required. The higher the reading on the vacuum gauge the dryer the soil.
Electronic equipment such as capacitance sensors (i.e. Enviroscan®, C-Probe®, Gopher®) measure
volumetric moisture at predetermined depths throughout the profile. This equipment has the capacity to
continuously log moisture content at any depth at which sensors are placed. Information can be graphed to
visually illustrate moisture at various depths. Fully automated systems can be set up to monitor and control
irrigation applications when moisture levels reach predetermined settings.
The advantage of capacitance soil monitors is that they continuously measure moisture levels, extraction
rates and drainage throughout the profile and present it in a visual format. Knowing what is happening below
the soil surface allows more precise irrigation management. Issues of under or over watering and nutrient
leaching are minimised resulting in better water use efficiency, improved crop performance and enhanced
natural resource protection.
There are many other types of monitors available than discussed here. Irrigation consultants and retailers
can recommend alternative types.
33
Figure 28. Enviroscan® chart showing moisture extraction at various depths
Figure 29a and b. Enviroscan® capacitance sensors and data logger
34
Figure 30. Installing an Enviroscan® in a maize crop
Figure 31a. Tensiometers at different depths in a peanut crop and b. Tensiometer with gauge
IRRIGATION SYSTEM CAPACITY
The capacity of an irrigation system is determined by the availability of water. Once that is determined the
infrastructure can be designed to match the resource. Most field crop irrigation systems in the NT are based
on centre pivots supplied by underground aquifers. Bore capacities may be as high as 100 L/second.
However, the majority range from 30 to 70 L/second. Good system design, installation and management are
critical for viable crop production.
Many irrigation systems are installed without sufficient planning or consideration of the physical environment
or available resources. A common mistake is that irrigation systems are too large for the amount of water
available. The sustainable yield of a bore should be determined through a pump test before the irrigation
35
system is installed. A pump test is the only way to accurately establish the draw down and recharge rates,
yield and the capacity of the bore.
Systems and bores which are subjected to long periods of continuous pumping at maximum rates are likely
to fail. Over pumping may result in sand being sucked into the system. This results in premature pump wear
and may cause the bore to collapse. Bores require time to recharge and each will vary in draw-down and
recharge rates. The NT Department of Natural Resources, Environment and the Arts (NRETA) can advise on
bore establishment, testing and maintenance.
Two aspects influence irrigation and crop management in the Top End. First, no useful rainfall occurs for
seven to eight months of the dry season. This means total crop water requirement must be supplied by
irrigation. Second, the arable red earths and many other soil types have low water-holding capacities and do
not store moisture for extended periods.
Bore capacity, flow rate and irrigation systems must match the intended size of the cropping operation.
When calculating water required for a particular area, peak and not average evaporative demand should be
used. Average figures result in under-estimating what is actually required when evaporative demand is at its
highest.
Peak water demand by maize could be as high as 60 to 70 mm per week for periods from August to
November. Two to three separate irrigations of 20 to 30 mm will be required, as one heavy application will
result in runoff, ponding and deep percolation. The specific soil type (i.e. clay loam or sandy loam) and soil
conditions will determine how much water can be applied at once. Tippera clay loams will accept
approximately 20 mm to 25 mm and sandy loams 25 to 35 mm before water starts to pond and run off.
With a given bore output, it is possible to work out how long it will take to irrigate the entire area to satisfy
crop water demand. This is critical for working out pumping schedules and determining whether the crop can
be irrigated sufficiently to avoid stress.
Example:
Assume a bore capacity of 70 L/second and potential area of 50 hectares, total peak crop requirement of 60
mm per week to be applied in two irrigations of 30 mm each.
Information: 70 L/second maximum flow = 252 000 L/hour

30 mm application required
50 ha area to be watered
1. Calculate how long it will take to apply 30mm to 50 hectares.
• First, calculate how much water is required to irrigate 50 ha.

• Calculate volume of water required to provide 30 mm over 1 hectare (ha)
• (i.e. 30 mm deep x 1 ha area = 0.03 m x 10 000 m2)
• = 0.03 m x 10 000 m2
• = 300 cubic metres (m3) required to water 1 ha
• = 300 x 1000 = 300 000 L required to water 1 ha
• Calculate amount (L) required for 50 ha = 300 000 L x 50 = 15 000 000 L
• Total water required = 15 000 000 L or 15 mega litres (ML)
• Time to irrigate 50 ha = Total water required divided by pumping rate
= 15 ML/252 000 L/hr (i.e. 70 L/sec)
= 15 000 000 L/252 000 L/hour
= 59.5 hours
36
Note: 1 cubic meter (m3) of water = 1000 L, 1 million litres = 1 mega litre (ML), 1 hectare = 10 000 m2
It takes 59.5 hours or almost 2.5 days to apply 30 mm to 50 hectares with 70 L/sec
2. Calculate how long to apply 60 mm to total area
Time to apply 30 mm = 59.5 hrs

Time to apply 60 mm = 59.5 x 2
= 119 hrs or almost 5 days
In this example, 119 hours of pumping is required to apply 60 mm of water. The irrigation system will be
operational for five out of seven days. While 40 mm to 50 mm may be required most weeks, the example
illustrates how to determine if a system is capable of effectively watering an area during peak water use. The
example does not show system losses or inefficiencies such as evaporation from the soil and friction losses
which further reduce water availability by 10% to 20%. Determining total water availability and peak crop
water demand is necessary to calculate maximum irrigable area, water schedules, pumping periods and
operational costs. Information from relevant advisors should be sought in the planning stages of an irrigated
cropping enterprise.
WATER PLANNING AND ALLOCATION
The NT Government is in the process of developing and implementing water allocation plans for the
Territory. Due to the increasing demand on water resources, allocation plans are necessary to ensure the
sustainability and equity of the resource into the future. Commercial irrigators require an extraction licence
from NRETA for extraction of 15 L/sec or more for specified agricultural and horticultural uses. There are no
charges associated with irrigation at present.
Once water plans are implemented, irrigators will have to apply for an allocation. Bores will need to be
metered to determine water use and total ground water extraction. Producers will have to budget to
determine how much of the crop can be grown to ensure there is enough water in their allocation to satisfy
crop needs. Water-trading, i.e. buying and selling water from other irrigators, is likely to become a feature of
irrigation in the Top End as it is elsewhere in Australia.
For example, one producer with an allocation of 1000 ML may budget on 5.0 ML/ha for 200 ha of maize.
Another producer may be more conservative and allocate 6.0 ML/ha for the crop reducing the planted area
to 166 ha.
If the producer who allocated 5.0 ML/ha finds there is insufficient water towards the end of the season due to
unexpected hot weather, he/she may have to consider one of several options. The grower may:
1. Continue watering the entire area at the budgeted rate and incur a yield reduction over the whole
crop
2. Sacrifice a portion of the crop and redistribute the available water to maintain full yield potential over
a reduced area, or
3. Purchase additional water to finish the original 200 ha of maize with full irrigation.
These are some of the decisions producers will have to make when irrigating in the NT, in future.
Management of irrigation and water is the key to profitability and sustainable resource protection. These
issues will become more important as demand for water and land grows in the NT.
37
Planning and developing well designed irrigation systems will pay dividends in terms of water use efficiency
and crop performance well into the future.
Figures 32a and b. Different sprinkler heads will give different efficiencies. Wobbler type sprinklers (left)
reduce drift and evaporative losses in high winds and hot conditions.
Key points:
• Maize requires 5.0 to 7.0 ML/ha of water depending

on variety, soil type and planting time.
• Using crop factors and daily evaporation rates will

help determine crop water demand. Soil monitors
will help fine-tune irrigation scheduling and
conserve water.
• Moisture stress at silking to grain fill will result in

the greatest loss in yield.
• Applications of 25 mm will be more efficient than

infrequent large irrigations (>33 mm) on light
permeable soils.
• Water allocation plans and water budgeting will

become an integral part of irrigation management
in the NT.
NATIVE AND FERAL ANIMAL DAMAGE
Damage from galahs, sulphur-crested cockatoos and pigs needs to be considered in small isolated maize
plantings. In areas close to water systems such as in Katherine and Douglas Daly areas, damage by birds
and pigs can be severe. Pig-fencing may be necessary in some locations. Pigs rampage through the crop
knocking it over to access the cobs. White cockatoos can do considerable damage during the seedling stage
and when the grain is maturing. They concentrate on the edge of crops, gradually eating their way in. When
they are in large numbers, losses can be substantial.
Prior to growing maize, consider the location and the potential damage from wildlife and other pests.
38
Figure 33. Damage to a maize crop caused by sulphur-crested cockatoos
HARVESTING
Two major issues impact on final crop yield and profitability:
• Correct setting and operation of the combine.

• Timely harvest (not delayed or late).
Maize is easy to harvest provided the combine is fitted with a specialised “corn” front. Maize fronts are either
“cutter bar” or “snapper bar” types with large crop dividers matching the crop row width. Cutter bar fronts cut
the maize stalks and thresh the whole plant and ear and are mainly used in dryland or low-yielding crops.
Snapper bar fronts strip the ear from the plant so that stalks are not taken into the harvester. Snapper bar
fronts range in size from four to 12 rows depending on header capacity.
Maize is physiologically mature when a black layer appears at the base of the grain where it attaches to the
cob. Grain moisture at this stage is around 28% to 32%, which is too high for storage. Grain in the NT is
mostly used as stock feed; so it is allowed to dry down in the field to a safe storage moisture content of 14%.
Maize can be harvested at higher moisture, but will require artificial drying before storage. As there is little
chance of rain and/or high relative humidity during August/September, maize will dry rapidly in the field and
artificial drying will usually be unnecessary.
Maize planted at the end of March can usually be harvested in late August when conditions are ideal.
Depending on variety, it will usually take between 135 and 160 days from planting to harvest at the correct
moisture content.
The adjustment to the front of the harvester is critical for harvest efficiency and for minimising grain loss. The
speed of snapper rolls on the front must be compatible with the forward speed of the harvester. A combine
which is incorrectly set-up or operated can result in 10% to 20% loss in the field. Delaying the harvest can
result in additional losses of 3% to 5%. These losses can be much higher if the crop begins to lodge or is
being attacked by birds or other pests. Harvest should commence as soon as the grain approaches 15%
moisture. If the crop begins to lodge or is being damaged by pests, it may be necessary to harvest it earlier
and artificially dry the grain.
39
Loss of grain at harvest significantly affects profit. For example, if a 10.0 t/ha crop loses 15% due to
harvesting inefficiency and if it takes 6.0 t/ha to cover costs, the loss due to inefficiency actually represents a
37.5% reduction in profit. This is because the loss of 1.5 t/ha (i.e. 10.0 t x 15% = 1.5 t) comes directly from
the profit of 4.0 t/ha (i.e. 1.5 t loss/4.0 t profit = 37.5%).
Every effort should be made to minimise harvest losses by ensuring that the machinery is well set up and
operated and the crop is harvested at the optimum time.
MAIZE AS A SOURCE OF FODDER AND ENERGY
Maize silage is the most widely grown fodder in the world. Silage is basically fodder which is harvested and
stored at high moisture (around 60%) and which undergoes fermentation. The fermentation process
conserves the fodder and produces a palatable, high energy (9.5 to 11.0 Mega joules of energy per kilogram
of dry matter) feed. Silage crops of 40.0 to 60.0 t/ha have been produced in the Top End. Silage crops are
produced in the same manner as grain crops but the complete plant is harvested at about 35% dry matter
(i.e. 65% moisture) which is approximately two weeks before physiological maturity. At this stage the grain is
partially soft and the milk line is about half way along the kernel.
Silage crops are harvested with forage harvesters or precision choppers, which cut the plant into lengths of
1.0 to 2.0 cm. Precision choppers make the best quality silage and the product is easier to compact and
conserve. Silage production is a specialized operation and requires specific handling and storage facilities.
Silage yields can be estimated by multiplying potential grain yields by 6. A 10.0 t/ha grain crop has the
potential to produce 60.0 t/ha of green chop or silage.
Maize can also be harvested as high moisture grain for stock feed. The grain is usually harvested at about
28 to 32 % moisture and ground in a tub-grinder to crack the grain and assist in the fermentation process. It
is then stored in specially designed high moisture grain silos or in pits as with normal silage.
‘Earlage’ is made by harvesting only the ears and husks (cobs) (as opposed to the whole plant) with a
snapper-bar and ensiled in the same way as silage. The ears are harvested at about 35 to 40% moisture,
similar to normal whole plant silage. This results in a high energy feed and most of the stover is returned to
the soil.
Maize is also being used increasingly for the production of ethanol, as a substitute for fossil fuels. Ethanol
production from maize (corn) rose in the US to a record high of 5.9 billion gallons in January 2007 and could
rise by as much as 60% by the end of the year. US ethanol consumption increased by 33% in 2006 to 5.4
billion gallons. According to the Renewable Fuels Association, the industry's primary trade organisation in
the US, there are now 114 ethanol distilleries, with an additional 80 new plants and seven expansions under
construction. A US federal mandate requires that there be a near-doubling in the use of renewable fuels,
from 2007 to 2012.
The dramatic increase in the use of grain for ethanol production has resulted in the doubling of the price of
corn in the US over the past year. This is a concern for many who believe the use of food crops for energy
could cause a shortage of grain for human and animal consumption.
Maize stover also has the potential to be used as a source of ethanol through a process of fermentation and
distillation of the cellulose. Cellulose is a major constituent of plant cell walls and is the most abundant form
of living biomass. Cellulose ethanol is gaining momentum as a viable bio-fuel alternative as companies
improve production technology. It may prove to be more environmentally sustainable and energy efficient
than ethanol from grain.
40
Despite the trend of increased bio-fuel use, there are arguments against the production of fuel from food
crops, both on environmental and economic grounds. Information on bio-fuels, their use and associated
issues is growing rapidly and is available from a wide range organisations and researchers on the internet.
THE ECONOMICS AND FUTURE OF IRRIGATED MAIZE PRODUCTION IN

THE NT
Irrigated maize is a high input crop. Seed, fertiliser, fuel and other inputs have a significant freight component
which adds to the cost of crop production in the NT. Growing maize in the NT may cost up to 30% more than
in Qld or NSW. However, the price of maize may also be higher in the NT than the national average due to
the higher costs of production.
Growing costs will largely be determined by the amount of fertiliser and water required. Water and fertiliser
account for over 60% of the total variable costs. Nitrogen requirements can be reduced significantly by
rotating maize with legume crops such as peanuts, mungbeans or legume pastures. Banding phosphorus
and nitrogen at sowing will be more efficient and help to reduce inputs. Using precision planters will reduce
seed requirements and ensure optimum seed depth, spacing and establishment. Using the most suitable
soils for maize production and avoiding problem areas or soils with low nutritional status will help reduce
production costs.
Planting maize at the earliest opportunity in the dry season or even late wet-season will reduce the amount
of water required. Using water monitoring equipment will help schedule irrigations more accurately and may
potentially save water.
CURRENT AND POTENTIAL MARKET
There is a limited market for maize at present in the NT due to the absence of dairy or feedlot industries. If
livestock industries intensify, maize should become more important. Maize has several industrial uses and is
being increasingly grown for ethanol production and bio-degradable plastics in Europe and the US. As high
yields can be achieved in the NT using irrigation, maize has potential for feedlots, in ethanol production and
other industrial purposes provided its cultivation is economical.
GROSS MARGIN FOR A SINGLE IRRIGATED MAIZE CROP
A gross margin is the difference between gross income and total variable cost of growing a crop. Gross
income is made up of total receipts from the sale of a maize crop. Variable costs, also referred to as running
costs, are directly related to growing, harvesting and marketing the crop. Gross margins do not take into
account fixed or overhead costs such as capital or interest, permanent labour, insurance, infrastructure and
other repairs, maintenance, replacement, depreciation and living or travel expenses. For this reason gross
margins are not a measure of the profit but more a measure of relative profitability when compared with a
similar enterprise.
Gross margins are useful in comparing different crops which require a similar level of input and resources.
However, it is unrealistic to compare gross margins of irrigated crops with those of dryland crops because of
the need for extra resources and infrastructure for irrigation. If major changes in the enterprise mix are being
considered, more comprehensive budgeting techniques are required.
Crop gross margins are usually based on a return per hectare. However, comparing different enterprises on
return per unit of permanent labour, per $1000 capital or per mega-litre of water used, is a worthwhile
exercise.
41
It has been suggested that it is possible to grow two crops per year using irrigation. While this was the
premise many peanut growers had in the late 1990s, experience has shown that it is difficult to grow two
successful crops in one year. Peanut producers found that delays in one crop exacerbated delays in the
following crop, which seriously compromised yield. Maize however, is a shorter season crop and requires
less ground preparation and harvesting time than peanuts. The problem with growing a wet season crop is
that it cannot be harvested before mid to late April in most instances due to the wet season. This means that
planting the following dry season crop has to wait until harvest is complete.
Growing two successful maize crops per year with irrigation may be possible provided stubble management,
planting time, pest, weed and disease control, water allocation and irrigation issues are effectively resolved.
Managing the soil and water resources in a sustainable way and developing viable markets are some of the
challenges for irrigated cropping in the Top End.
The following gross margin is based on a fully irrigated dry season crop on a sandy red earth in which the
level of inputs is aimed at achieving 10.0 t/ha. No allowance for residual soil fertility is made. Fertiliser and
chemical prices are based on quotes received from agribusinesses in Darwin in January 2007, which are
subject to change. Grain price is based on an estimate provided by local growers/buyers.
42
Table 11. Gross margin for irrigated maize on Blain soil at Douglas Daly/Katherine, NT
Per Your
hectare estimate
t/ha price/t
Yield 9.5 250 2375
Total Income 2375
Variable Costs
Land Preparation
1 disk 10
1 chisel 9
2 scarify 15
Sowing
Operation 4
$/bag bags/ha for 78 000 plants/ha
Seed Gaucho® treated 264 1.1 290.4
Fertilizer
Pre-plant application by 3 9
250 kg of DAP/SOA 20:13:0:13 at 900 per ton 225
250 kg Urea at 720 per ton 180
20 kg zinc hepta-hydrate or equivalent at 1316 per ton 26.32
200 kg MOP at 875 per ton 175
50 kg/ha DAP plus TE at planting at 1000 per ton 50
Fertigation
200 kg urea at 720 per ton 144
10 kg zinc hepta-hydrate at 1316 per ton 13.16
Weed Control
Application L/ha $/L 3
Primextra Post-plant pre-emergent 5.0 at 13.4 67
Insect control
Chlopyrifos 0.9 10 9
Irrigation ML $/ML
Pumping costs 5.5 at 60 330
$/t
Harvesting 10 100
Total Variable Costs 1659.88

Gross Margin 715.12
Seed as % of total variable costs: 17
Fertilizer as % of total variable costs: 49
Water as % of total variable costs: 20
Notes:
• DAP/SOA is a di-ammonium phosphate/sulphate of ammonia blend to supply N, P and S.
• Fertiliser may be reduced on soils with good fertiliser history and on heavier clay loams.
• Input costs may be lower with bulk purchases and economies of scale.
43
Table 12. Effect of price and yield on gross return
Expected Expected yield (t/ha)

on-farm 6 8 10 11 12 13
price ($/t)
$100 -1076 -876 -676 -576 -476 -376
$150 -776 -476 -176 -26 124 274
$200 -476 -76 324 524 724 924
$250 -176 324 824 1074 1324 1574
$275 -26 524 1074 1349 1624 1899
$300 124 724 1324 1624 1924 2224
$325 274 924 1574 1899 2224 2549
Total variable cost: $1676
WORLDWIDE DEVELOPMENTS IN MAIZE PRODUCTION AND

TECHNOLOGY
Maize is one of the world’s most important crops and according to the FAO, demand for it as a food and
industrial crop will increase dramatically within the next 20 years. FAO predicts that an additional 295 million
tonnes (almost half of world’s current production) will be needed by 2030. Demand in the US has already
surged where competition from the ethanol industry has doubled the price of maize in the past year. Even
though maize is a minor crop in Australia, annual production has more than doubled in the past eight years
to 530 000 tonnes.
Billions of dollars are spent each year on maize research and development. Those involved include
biotechnology, seed and agrichemical companies, universities, state and federal departments of agriculture
and development agencies such as the International Maize and Wheat Improvement Centre (CIMMYT).
As a result of the advances in maize research, yields as high as 26.0 t/ha and 21.0 t/ha have been achieved
in the US and Australia, respectively.
Major advances in maize and other crop research during the last 10 years have been in biotechnology and
genetic engineering. This involves the transfer of genetic material and traits (often from other organisms) to
plants to improve their quality, yield or resistance to pests. Maize has been genetically engineered to resist
attack by a range of economically important pests and to tolerate herbicides such as glyphosate (i.e.
Roundup®) to improve crop weed management.
Bacillus thuringiensis (Bt) is a soil bacterium that produces an insecticidal protein. The protein has been
genetically transferred to maize with the result that the crop produces a Bt toxin against pests. When
attacked by specific insects (i.e. heliothis) the toxin is ingested; feeding stops and eventually the pest dies. Bt
corn is now commercially available in a number of countries and in 2006 over 60% of the US corn crop was
genetically modified. This trend is increasing as the benefits of genetic engineering technology are being
realised through better yields, improved insect and weed management, reduced pesticide usage and
improved grower returns.
Maize is available now in the US which has been “stacked” with genetic material conferring several traits.
Monsanto markets “triple trait” maize varieties which are genetically modified (GM) to resist rootworms and
other soil insects, corn borers and is also glyphosate tolerant. The GM maize is marketed as YieldGard®Plus
with Roundup Ready® Corn 2.
44
Biotechnology has its critics and many countries and jurisdictions are still resisting the push to adopt GM
crops. However, GM crops are commercially proven across millions of hectares worldwide and are
increasing at such a rate that some predict 95% of the US maize crop will be GM in the next few years. The
European Community is also embracing some aspects of GM agriculture.
Biotechnology is destined to play an even greater role in improving the efficiency of generating bio-fuel from
maize and other crops. It is predicted that within 10 years GM maize will provide double (i.e. 600 US gallons
per acre of ethanol from grain and 200 US gallons per acre from stover) the amount it now produces per
hectare. Genetic engineering is being used to improve the nutritional and industrial qualities of maize,
develop specialty products and is destined to play an ever increasing role in world agriculture.
The use of GM crops comes with an obligation of managing the crop and surrounding area in a specific
manner. There are strict guidelines about the use of GM crops and the requirement to implement an insect
resistance management (IRM) program to help to protect the longevity of the technology.
Other advances in plant genetics which are enhancing traditional breeding and maize improvement include
in-vitro culture and selection, genomic analysis and molecular breeding, or marker assisted selection.
Advances have been made in maize tissue culture which have enabled more detailed study of the genetic
make-up of plants and accelerated genetic manipulation, selection and regeneration of transgenic plants.
Mutagenesis, which is recognized as a traditional breeding technique, is used to develop maize which has
specific traits. The Clearfield® technology system is an example of where herbicide-tolerant maize is
specifically developed for an integrated weed management system using imidazolinone herbicides.
Other advances include new age polymers, seed coatings and insecticidal/fungicidal seed dressings. Landec
Ag has developed the Intellicoat® patented seed coat which stimulates seeds to germinate once the soil
reaches a prescribed temperature. This is used in the US and Europe where farmers want to plant earlier in
cool soil and require the crop to germinate once temperatures become favourable.
New low-toxicity, low rate, systemic seed dressings (such as Gaucho® and Cruiser® which have been
described) have been developed to protect the seed and young plants from a range of economically
damaging diseases and insect pests. The benefit of this technology is that the pesticide is applied directly to
the seed and eliminates the need to handle or apply multiple in-crop pesticides. The chemical is systemic
and protects the plant for several weeks and acts specifically on the target pest.
There is an increasing trend of agrichemical, seed and biotechnology companies combining to develop new
technology. In the US when farmers purchase GM seed they are buying a complete crop management
system and a licence to use the technology according to specific production guidelines.
Maize technology is advancing at a rapid rate due to the worldwide importance of the crop. Improvements
will continue to come from traditional breeding while biotechnology will play an increasing role in trait
identification and selection.
45
GLOSSARY
ADMA Agricultural Development and Marketing Authority, established in 1980 by

the NT Government to assist with agricultural development in the Top End.
Banding (fertiliser) Applying fertiliser in a “band” or strip below or beside seed at planting.
Blain soil Dark reddish-brown sand to loamy sand. Profile graduates to sandy loam to
sandy clay loam at 30 cm. Easy to cultivate and is not hard setting.
Buffering capacity The ability of soils to resist changes in pH.
Chemigation The application of chemicals in irrigation water.
Cob Term used for the ear of corn.
Conventional cultivation The use of heavy machinery such as ploughs to cultivate and prepare land
for crops.
Corn Term used to describe the major cereal (maize), largely used in the US
Crop factor An estimate of the ratio of plant water use to pan evaporation, (usually
between 0.3 and 1.2). A crop factor of 0.7 estimates that the plant is using
70% of pan evaporation.
Drained upper limit The volume of water a soil can hold two to three days after saturation and
when free drainage has practically ceased, also termed field capacity.
Drained lower limit The moisture content of a soil at which plants wilt and fail to recover, also
called wilting point.
Fertigation The application of fertiliser through the irrigation system.
Ethanol A flammable, colourless alcohol produced through the fermentation of plant
sugars for use in alcoholic beverages and industrial purposes such as the
production biofuel. Also known as ethyl alcohol, drinking alcohol or grain
alcohol.
Enviroscan® A capacitance probe which measures soil moisture.
Ear Synonymous with cob.
Evapo-transpiration The combined evaporation from a crop surface and surrounding soil surface.
Genetically modified An organism whose genetic material has been altered using genetic
organism (GMO) techniques generally known as recombinant DNA technology.
Infiltration The rate at which water enters the soil before it begins to run off or pond on
the surface, measured in mm per hour.
Lodging Crop falling over due to wind, disease or weak stalk.
Maize Native American name for the crop.
Mega litre One million litres (of water).
Nutrients Elements necessary for plant health and growth supplied by the soil or in
applied fertiliser.
Oolloo soil Dark, reddish-brown sandy loam, graduating to sandy clay loam, to clay
loam at 30 to 40 cm. Its intermediate texture is between Tippera and Blain
soils.
Pan-evaporation The amount of daily evaporation from a specially designed and located pan
(US Class A pan).
Percolation The movement of water downwards within the soil profile.
46
Physiological maturity When grain has reached maximum dry matter and its development is
complete.
Red earths A diverse group of arable, well drained soils under the Great Soil Group
Classification (Stace et al. 1968) with characteristics which determine their
use and productivity. Colours range from deep red to reddish-brown. They
are common agricultural soils in the Katherine Daly Basin. They are known
as Kandosols under the Australian Soil Classification.
Respiration The uptake and storage of carbon dioxide in the process of converting it to
carbon through photosynthesis.
Soil pH The relative acidity or alkalinity of the soil.
Silage Conserved and fermented high moisture plant material used for stock feed.
Silking The emergence of silks (female reproductive part) from the top of the
immature ear.
Standability The ability of the crop to stand and resist lodging.
Stover Stalk or mulch left over after harvest.
Systemic (as in pesticide) An insecticide whose mode of action is via uptake into a plant, entering the
pest when the plant is consumed.
Tasseling When the tassels (male reproductive part) emerge from the top of the maize
plant to release pollen.
Tensiometer A vacuum tube fitted with a gauge used to measure soil water tension.
Tippera soil Dark red to reddish-brown, hard loam soils. Soil profile increases in clay at
30 to 40 cm. Sets hard on drying and forms soil surface crust under
conventional tillage.
Top End The northern most area of the Northern Territory (north of latitude 15° South)
Trace element Elements essential to plant growth which are taken up in minute quantities,
such as zinc, copper, boron etc.
Transgenic plants Plants that possess genes that have been transferred from a different
species. Today the term refers to plants produced in a laboratory using
recombinant DNA technology in order to create plants with specific
characteristics by artificial insertion of genes from other species.
Zero-till Establishing crops without any preliminary cultivation and controlling weeds
with herbicides.
47
APPENDICIES
APPENDIX 1. USEFUL WEBSITES
Organization Web Site

Australian Centre fro International Agricultural Research (ACIAR) www.aciar.gov.au
Australian Pesticides and Veterinary Medicines Authority www.apvma.gov.au
Council for Biotechnology Information www.whybiotech.com
CSIRO www.csiro.com.au
Farm Industry News www.farmindustrynews.com
Farmers Info Australia www.nswfarmers.org.au
Farmlink Research www.farmlink.com.au
Fat Cow Farming www.fatcow.com.au
Food and Agriculture Organisation of the UN www.fao.org
Grains Research and Development Corporation (GRDC) www.grdc.com.au
InfoPest database www2.dpi.qld.gov.au/extra/asp/infopest
International Maize and Wheat Improvement Centre (CIMMYT) www.cimmyt.org
Kondinin Group www.kondinin.com.au
Maize Association of Australia www.maizeaustralia.com.au
National Corn Growers Association of the US www.ncga.com
NSW Department of Primary Industries www.dpi.nsw.gov.au
NT Department of Primary Industry, Fisheries and Mines www.nt.gov.au/dpifm
Queensland Department of Primary Industries and Fisheries www.dpi.qld.gov.au
Rural Industries Research and Development Corporation www.rirdc.gov.au
University of Queensland www.uq.edu.au
Victorian Department of Primary Industry www.dpi.vic.gov.au
48
APPENDIX 2. MAIZE CROP GROWTH STAGES AND MANAGEMENT GUIDE
(Courtesy NSW Department of Primary Industries)
49
Stage and Duration Management

Sowing to seedling emergence (4-5 days) Starter fertilizer (NPK with trace elements) should
Seed reserves provide energy for the emerging be banded below and to the side of the seed. Seed
seedling. The primary root develops and the shoot (treated with registered fungicide and insecticide)
emerges from the soil. Leaves appear at the rate of should be planted at a uniform depth and spacing
one leaf every three days. The growing point remains into moist soil. Monitor seedlings for insect damage.
below the soil for about three weeks after sowing. Apply pre-emergent herbicide.
Early vegetative (seedling emergence to tassel The secondary roots can be damaged by cultivation.
initiation – 5 weeks) Post emergent herbicides can be applied until the
Two weeks after emergence the secondary root crop becomes too tall.
system takes over from the primary roots. At about
day 20 the potential ears are starting to form. Leaf
formation is at its most rapid stage. At week five the
plant has 8 fully emerged leaves and the tassel starts
to develop in the growing point.
Late vegetative stage to tassel emergence (3-4 Nutrients and water must be freely available. N can
weeks) be applied by side-dressing or through the irrigation
At about six weeks, the plant has 10 leaves and is water. Ensure all “top-up” nutrients are applied at
growing rapidly and taking up nutrients and water in this time in advance of flowering and pollination.
large quantities. Kernel number and ear size are Ensure all of K has been applied.
being determined. At the 12th to 17th leaf stage (day
40-55) the number of potential kernels and the size of
the ears will be set.
Flowering (pollination & fertilisation, 3-8 days) Stress at this time will cause poor pollination, barren
At about week 9, tassels emerge and shed pollen 2 tips and have the biggest impact on yield. Monitor
to 3 days before silks emerge. Silking occurs at about the crop for insect pests and protect the silks from
day 65. It takes another 2 to 3 days for all of the silks damage. The two weeks prior to pollination (about
to be exposed and pollinated. Two weeks after day 50) and two weeks after pollination (about day
silking, nutrients are being relocated from leaves and 75) is the most critical period for determining maize
stems to the ear and seed. yield. Ensure water and nutrients are adequate.
Grain filling - physiological maturity (8-9 weeks) Moisture and nutrient stress will result in small grain
Ears have developed 12 days after silking and the and reduced yield. Stress may pre-dispose the plant
grain starts to fill. N and P uptake continues at a rapid to disease and lodging. Bird and pig damage may
rate. Denting of grain occurs 35-40 days after silking. be an issue in some areas and preventative
Physiological maturity occurs 55-65 days after silking. measures may need to be taken.
A black layer develops at the tip of the seed where it
joins the husk, indicating physiological maturity.
Grain drying (35 days depending on conditions) Artificial drying is usually un-necessary in the NT
Grain gradually dries and leaves hay off. Harvest unless the crop starts to lodge or there is the threat
occurs at about 150 – 160 days after emergence of damage by birds or pigs. Harvest the crop as
when the grain has reached 14 % moisture and is soon as it reaches a safe moisture level.
safe for storage.
Maize yield is enhanced by long, warm days and cool nights. High temperatures will hasten maize
development reducing the time for dry-matter and yield accumulation. Crops which mature in mild
rather than hot conditions will have a higher potential yield.
50
APPENDIX 3. EVALUATION OF IRRIGATED MAIZE ON BLAIN SOILS, DOUGLAS DALY RESEARCH

FARM, 1999 TO 2002
Abstract
Formal research into rain-fed maize in the NT began in 1954. The Animal Industry and Agriculture Branch of
the Northern Territory Administration conducted trials at Berrimah Farm, Batchelor and Tortilla Flats
(Muchow 1985). Trials continued until 1963 but yields were disappointing due to weed infestation,
waterlogging, drought and diseases, including “Wallaby Ear” virus. Trials were also conducted at Tipperary in
the 1970s where the best plot yields were 5.2 t/ha.
With the implementation of the Agricultural Development and Marketing Authority (ADMA) at Douglas-Daly in
the early 1980s, maize was commercially grown for about 12 years. Plantings peaked in 1987/88 when 1725
hectares (ha) were sown. Yields reached 4.0 to 5.0 t/ha, but the average district yield was less than 3.0 t/ha
(Price 1982 and 1983, Garside and Price 1984, Price 1985 to 1988). Airey (1972) and Roberts (1986)
reviewed early maize research in the NT. Airey suggested that maize had a limited potential as a dryland
crop and Roberts suggested that the highest priority for research was the nutritional requirements of the
crop.
In the mid 1990s interest in irrigation increased and several commercial irrigated peanut operations were
established in Katherine and Douglas Daly. Maize was seen as an ideal rotation crop; however, there was
little experience or data on growing irrigated maize on sandy surfaced soils. In 1999 the Department of
Primary Industry, Fisheries and Mines (DPIFM) began evaluating commercial and experimental maize lines
to assess their productivity under irrigation on Blain soil at Douglas Daly Research Farm (DDRF).
Over four years (1999 to 2002), the average maize yield for all varieties was 9.3 t/ha. When the 2000 season
results are excluded, due to incomplete pollination, the average yield for all varieties and for the best four
varieties was 10.3 t/ha and 11 t/ha, respectively.
Introduction
In the late 1990s DPIFM and the newly-formed NT Irrigation, Grain and Fodder Producers Association
(NTIGFPA), promoted irrigated agriculture in the Top End. Irrigation was seen as a means to increase
viability and decrease risks associated with wet season production. However, there was little data on
irrigated crop production in the Top End as most of the research had been conducted under dryland
conditions.
Despite this lack of knowledge, a number of interstate and local producers installed centre pivots specifically
to grow peanuts. Wet season grown peanuts had shown potential (Price 1985 to 1988) and it was believed
that peanuts would also perform well under irrigation. Friable, free-draining, sandy red-earth soils (Blain and
Ooloo soil types) were selected for peanut production. The soils are easy to cultivate and allow peanuts to
be dug and harvested efficiently.
Due to the high cost of establishing irrigation infrastructure, it is necessary to assess alternative crops and
develop a viable crop rotation. Maize was chosen as one possible option because of its high yield and
market potential. A maize-peanut cropping system is potentially a good rotation because the nitrogen fixed
by the legume can be utilised by the maize crop and pests, disease and weeds can be managed more
effectively.
However, there was no information available on the performance of irrigated maize on sandy soils. Past
experience with maize on sandy soils in the wet season, indicated the crop suffered from a range of
nutritional disorders and yields were low (Roberts 1986, Price 1985 to 1988).
51
The performance and agronomic requirements of maize grown on light soil needed to be assessed before
recommendations could be given to growers. Commercial hybrids also required evaluation to determine the
best varieties for the Top End. DPIFM evaluated irrigated maize on Blain soil at DDRF for four years (1999 to
2002) to determine the crops potential. The evaluation was conducted using centre-pivot irrigation and the
maize was grown in rotation with peanuts and green manure crops. The results and conclusions from this
evaluation are outlined in the following report.
Objectives
• To assess the nutritional, water and pest management requirements of irrigated maize crops on light
soils in the NT.
• To determine yield potential, production costs and viability of irrigated maize in the NT.
• To identify suitable and adapted commercial hybrids for NT conditions.
• To develop and document recommendations for irrigated maize production in the NT.
Location and soil type

The research was undertaken at DDRF, near the junction of the Douglas and Daly Rivers, (13º50´ S,
131º45´ E, altitude less than 200 m), 220 km south-west of Darwin. The soil type is a Ruby-Blain, red earth
(Figure 1) under the Great Soil Group classification (Northcote 1979). It falls in the sandy subgroup along
with Venn and Oolloo soil types of the Top End. These soils are classified as Kandosols under the
Australian Soil Classification system (Isbell 2003). Blain soils are well drained and have a pH of 6.0 to just
below neutral. They are massive in structure and have a dark reddish brown sand or sandy loam profile to
about 40.0 cm. The soil profile graduates to a dark-red sandy loam to sandy clay loam below 40.0 cm. Clay
content in the surface layers (0-20 cm) is around 7% and may increase to 50% at depths of 80.0 to 90.0 cm
(Lucas 1983).
The dominant clay material is kaolinite and fine sand accounts for 50 to 70% of the particle size analysis.
Blain soils have a low cation exchange capacity, low organic matter content, are low in all the essential
elements and have low water holding capacities (Lucas 1983, Aldrick and Robinson 1970, Williams, Day,
Isbell and Reddy 1985). Volumetric available water holding capacity of Blain soils varies from 4.0 to 7.5 %
(i.e. 40.0 to 75.0 mm/m of soil depth) depending on soil condition and clay content (Dilshad et. al. 1996).
DRY SEASON 1999
Materials and methods

The trial site consisted of 5.0 ha on one side of a 10.0 ha centre pivot on Circle 2 at DDRF. The area was
sown with a mungbean green manure crop in December 1998. The mungbeans were disk-ploughed and
incorporated in late February 1999. The area was cultivated twice with a scarifier to prepare a friable
seedbed. The area was soil sampled to a depth of 150.0 mm in February and analysed for nutrient content
(Table 1). The trial was sown on 25 March 1999.
Nine varieties of maize were evaluated (Figure 5) in a randomised complete block design experiment with
four replicates. Blocks consisted of four rows by 100.0 m of crop (Figure 2). The design was maintained over
the four years of evaluation; however, the number of replicates, the number of rows and plot sizes varied
depending on the number of cultivars evaluated in a particular season.
The varieties were sown with an eight-row “Mason Maxi-Strike” planter. The planter components consisted of
twin opening disks. Seed dropped between the disks into the open furrow and two inclined press-wheels
52
close the furrow. The aim was to plant 7 to 8 seeds/m at a 75 cm row spacing to achieve a population of
around 75 000 plants/ha. However, the planter could only be calibrated to around 10 seeds/m resulting in a
population of over 91 000 plants/ha.
This population was between 17 and 22% higher than recommended by the seed companies. To assess
whether the higher population influenced yield, plots measuring 2.0 m by four rows were hand-thinned three
weeks after establishment to the recommended population of between 75 000 and 80 000 plants/ha. Hand
harvests were taken from the thinned plots and from equivalent areas in un-thinned crops to determine if
either population influenced yield.
Pre-plant fertiliser was broadcast and worked into the soil at the rate of 130.0 kg of nitrogen (N), 26.0 kg of
phosphorus (P), 20.0 kg of sulphur (S), 150.0 kg of potassium (K), and 81.0 kg of magnesium (Mg)/ha. Zinc
(Zn) and boron (B) were applied through the fertigator (dissolved in water and injected through the irrigation
system) at the rate of 10.5 and 1.5 kg/ha, respectively. About 100 kg/ha of MAP Sulcote® +TE (mono-
ammonium phosphate plus trace elements i.e. 9% N, 19% P, 12% S, 2.5% Cu and 2.5% Zn) was applied
through the planter and dropped on top of the row and partially incorporated by the opening disks on the
planter. Approximately 92 kg/ha of N (as urea) was split-applied through the fertigation system at 30 and 55
days after sowing (DAS). Total nutrients applied are presented in table 2.
Primextra® herbicide (277 g/L a.i. metolachlor and 223 g/L a.i. atrazine) was applied at 5.0 L/ha immediately
after planting followed by 10.0 mm of irrigation to control broadleaf and grass weeds. On 10 April 3.0 L/ha of
Nutrazine® (500 g/L atrazine a.i.) was applied in conjunction with Lorsban® insecticide (1.0 L/ha of 300 g/L
a.i. chlorpyrifos) to provide additional residual weed control and to control leafhoppers. Rogor® insecticide
(0.5 L/ha of 400 g/L a.i. dimethoate.) was applied on 17 April to control leafhoppers and Larvin® insecticide
(2.0 L/ha of 375 g/L a.i. thiodicarb) was applied by helicopter on 8 May to control armyworms, heliothis and
green vegetable bugs (GVB).
Tissue samples were taken 30 DAS and at silking and analysed by the chemistry laboratory at Berrimah
Farm to determine nutrient status. Samples were taken in accordance with recommendations in Reuter and
Robinson (1997). Whole plant tops were analysed at 30 DAS and the leaf blade opposite and below the cob
(bobc) at silking (see Table 3).
The crop was irrigated using a centre pivot and received approximately 4.8 ML/ha of water. Jetfill®
tensiometers were used to assist with irrigation scheduling and total water consumption was recorded on a
bore metre.
Hand harvests from the two population areas were undertaken on 20 August and the ears were threshed
and weighed; grain moisture was recorded using a grain moisture meter. The main trial was harvested on 26
August, with an International® 1420 axial flow header fitted with a four-row snapper-bar maize front. Plot
yields were measured and nutrient composition of the grain and stover was assessed. Weight of grain was
corrected to 12% moisture. Krondomic (kg/hectolitre) weight was also measured for each variety.
Table 1. Indicative soil nutrient levels prior to the 1999 planting
Nutrients
K Mg P S Zn Cu
Available
80.0 mg/kg 50.0 mg/kg 15.0 mg/kg 2.1 mg/kg 1.7 mg/kg 1.3 mg/kg
levels
53
Table 2. Fertiliser applied during the 1999 maize evaluation at DDRF
N P K S Cu Zn Mg B
Timing kg/ha Type $/Ton* $/ha
(kg/ha) (kg/ha) (kg/ha) (kg/ha) (kg/ha) (kg/ha) (kg/ha) (kg/ha)
Preplant 200 19:0:13:10 38 26 0 20 0 0 0 0 665 133.0
Preplant 200 Urea 92 0 0 0 0 0 0 0 702.5 140.5
Preplant 300 MOP 0 0 150 0 0 0 0 0 555 166.5
Preplant 150 Granomag 0 0 0 0 0 0 81 0 852 127.8
Zinc Sul
Fertigate 50 0 0 0 0 0 10.5 0 0 810 40.5
Hepta
7.5 Solubor 0 0 0 0 0 0 0 1.5 3000 22.5
MAP.
At Planting
100 Sulcote+ 9 19 0 12 2.5 2.5 0 0 881.5 88.2
9:19:0:12
TE
Sub total 139 45 150 42 2.5 13 0 0 719
30 Urea plus
Fertigation 13 9 57.45
Urea Zinc
Urea
Fertigation 100 46 0 0 0 0 0 0 0 702.5 70.25
30 DAS
Urea
Fertigation 100 46 0 0 0 0 0 0 0 702.5 70.25
55 DAS
Total 244 45 150 42 2.5 22 81 1.5 916.95
Note: *1999 fertiliser prices
Figure 1. Ruby Blain, sandy red earth at DDRF
54
Figure 2. Maize evaluation plots under centre pivot irrigation at DDRF
Results and discussion

Establishment and nutrition
Eight out of nine varieties established well and achieved an average population of 91 500 plants/ha which is
approximately 17% to 22% higher than recommended by commercial seed companies. Pacific 338 was the
only variety with low establishment due to poor seed quality and vigour. It achieved only 52 000 plants/ha,
which is 30% lower than the recommended population. Consequently, Pacific 338 had a significantly lower
yield than all other varieties.
Figure 3. Commercial header used to harvest maize evaluation plots at the DDRF.
55
Within a week of emergence, N and P deficiency was evident in sections throughout the trial. The deficiency
was traced back to a design fault in the fertiliser metering system on the planter. Fertiliser was applied
intermittently instead of in a continuous stream with the result that sections of the crop completely missed out
on fertiliser giving a “patchwork” deficiency pattern throughout the trial area (Figure 4). Analysis at 30 DAS
confirmed that the crop was low in N and marginal for P (Table 3).
Figure 4. N deficiency due to poor distribution of fertiliser at planting time
On 9 April the crop was fertigated with 30.0 kg/ha of N as urea and 9.0 kg/ha of Zn as zinc sulphate
heptahydrate. Early N deficiency will limit the leaf and cob size and reduce potential yield. Mg concentration
at silking was a little lower than recommended and Zn was considerably higher. The crop eventually
recovered from the initial N and P deficiency. Plant tissue analysis revealed that nutrients were adequate at
silking and within the range specified by Reuter and Robinson (1997).
Table 3. Average nutrient concentration of irrigated maize and recommended ranges* for different stages of
growth
Nutrient levels
N P K S Ca Mg Zn Cu Fe B
Growth stage
% % % % % % ppm** ppm ppm ppm
30 DAS***
2.7 0.36 3.59 0.21 0.38 0.19 79.7 7.7 107 7.09
(measured)
Recommended 0.30- 2.5- 0.15-
3.5-5.0 0.2-0.3 0.3-0.7 20-50 7-20 50-300 7-25
range* 0.5 3.0 0.45
Silking
3.3 0.32 2.3 0.22 0.46 0.13 153 10.5 89.8 6.2
(measured)
Recommended 0.27- 2.1- 0.15- 0.21-
2.7-3.3 0.2-0.5 25-70 6-20 20-200 6-25
range* 0.62 3.0 0.5 0.5
* Recommended ranges derived from Reuter, D.J. and Robinson, J.B. 1997(eds) Plant Analysis 2nd Edition.
** ppm = parts per million, *** DAS = days after sowing.
Total applied N was 244.0 kg/ha. At an average yield of 9.5 t/ha (average of all varieties) the crop took up
180.0 kg of N, leaving a residual of 64.0 kg N, some of which is lost or immobilised by micro-organisms. This
N would allow an additional yield potential of about 3.0 t/ha if all applied N was utilised. However, some
56
varieties yielded 11.0 t/ha and utilised over 200.0 kg of N, equivalent to 85% of applied N. Had the
application of fertiliser at planting been more efficient, the recovery of N and yield may have been higher.
Table 4. Nutrients taken up by a 10.0 t/ha irrigated maize crop at DDRF in 1999
N P K S Ca Mg Zn Cu Fe
Plant part
kg kg kg kg kg kg grams grams grams
Nutrient removed per
6.0 0.42 15.1 0.48 2.5 1.6 27 4 34
tonne of stover
Nutrient removed per
13 2.3 2.75 0.91 0.04 0.88 18 2 12
tonne of grain
Total nutrients removed
130 23.0 27.5 9.1 3.8 8.36 171 19 114
in 10 t of grain
Total nutrients taken up
190 27.2 178.5 13 .9 27.5 23.5 441 57 454
in grain and stover*
* The total nutrient taken up in a 10 t/ha grain crop with 8.0% protein. A 10 t/ha grain crop produces an equivalent
amount of stover. Nutrients in the stover are returned to the soil when it is ploughed back.
Variety performance and plant population

The trial crop was harvested on 26 August, 153 DAS when grain moisture was below 15%. Grain moisture
was recorded and grain weight was corrected to 12% moisture.
PIONEER 3237 was the best performing variety at 11.09 t/ha and was significantly better than five other
varieties. HYCORN 75, PIONEER 31M10 and DK 689 were the next best yielding varieties (Figure 5). All
varieties yielded 9.0 t/ha or higher except PACIFIC 338 which had a significantly lower yield due to poor
seeding vigour and emergence. It also had significantly lighter grain than most of the other varieties. The trial
area averaged 9.40 t/ha. The poor fertiliser distribution at planting may have reduced overall yield potential.
A comparison of the high and low populations (i.e. the thinned and un-thinned) showed there was no
significant difference in yield or grain density (i.e. kg/hectolitre) between or within varieties, when variety
Pacific 338 was excluded from the analysis (Tables 5 and 6). While the yield of individual varieties varied, it
was not influenced by either population in this trial. Pacific 338 had a significantly lower yield and this was
due to its poor establishment, low population and lighter grain. This showed that when populations are
significantly lower (i.e. 30% lower) than recommended, there will be a big yield penalty. For all other
varieties, 75 000 to 80 000 plants/ha gave an equivalent yield to that of 91 000 + plants/ha. This illustrates
that there is a tolerance to slightly higher plant populations (17 to 22%) than recommended but no yield
advantage or penalty. However, in commercial practice higher populations than recommended will result in
unnecessary seed costs and may induce lodging (due to thinner stalks) at the end of the season.
57
Yield Grain Weights
16.00 100.0
14.00
95.0
Grain Weight (kg/100L)

12.00
90.0
10.00
Yield (t/ha)
8.00 85.0
6.00
80.0
4.00
75.0
2.00
0.00 70.0
Pioneer Hycorn Pioneer Pioneer Pioneer Pacific Pioneer Pacific
DK 689
3237 75 31M10 3153 3394 269 1196K 338
Yield 11.09 10.26 10.22 9.82 9.66 9.65 9.17 9.00 6.00
Grain Weights 79.0 79.1 78.3 78.5 80.3 76.4 77.3 81.6 76.1
Variety (1999)
Figure 5. Yield and grain weights for the 1999 maize variety evaluation at DDRF with 95% confidence
intervals
Table 5. Plot yield (kg/plot) analysis of varieties in thinned and un-thinned maize populations
Variety Weight - mean

Thinned 6.600 a
Unthinned 6.445 a
LSD (p<0.05) 0.3467
p-value 0.368 (not signif)
CV (%) 11.0
Means with a common letter are not significantly different
Thinned = 78 000 plants/ha. Unthinned 91 500 plants/ha
Table 6. Plot grain density (kg/100 L) analysis for thinned and un-thinned maize populations
Variety Original scale

Thinned 77.300 a
Unthinned 76.746 a
LSD (p<0.05)
p-value 0.146 (not signif.)
CV (%) 0.5
Means with a letter common letter are not significantly different
Thinned = 78 000 plants/ha. Unthinned 91 500 plants/ha
Weeds, pests and diseases

The application of Primextra® provided excellent control of broadleaf and grass weed. Nutgrass (Cyperus
rotundus) was the only weed not controlled. Nutgrass is becoming an increasing problem on the
experimental areas at DDRF.
Insect pressure was high throughout the 1999 dry season. Large populations of leafhoppers, (Circadulina
bimaculata), heliothis (Helicoverpa spp.), Northern Armyworm, (Mythimna separata) and the green vegetable
58
bug (GVB) (Nezara viridula) were present and required control on three occasions. GVB can build-up to
extremely high populations, feeding on and shrivelling the developing kernels and distorting the ears. This
allows heliothis to enter the ear sheath and cause further damage (Figures 7 and 8).
Leafhoppers are small mobile insects which are difficult to detect. They are a serious pest because they
transmit WEV which stunts and renders maize plants unviable (Figure 6). They were present in the crop from
the first week after emergence. Their eradication within the first 14 days is critical for disease control. If not
managed, WEV is one of the most severe diseases affecting irrigated maize in the NT. Leafhopper
infestation in irrigated maize is a constant threat because the crop is usually the only alternative source of
food available in the dry season.
The chemical applications were effective in protecting the crop; however, by harvest, GVB had re-
established in large numbers (two to four insects per plant) from adjoining legume pastures. An integrated
pest management program should be an integral part of commercial maize production in the NT.
Note enlarged veins and upright growth
Figure 6. (a and b) Symptoms of wallaby ear virus transmitted by leafhoppers
Figures 7a and b. (a) Helicoverpa larva feeding on young maize ear. (b) Green vegetable bug and egg raft
on maize leaf
59
Figures 8a and b. (a) Northern armyworm damage in maize (b) Armyworm larva
Irrigation requirements
The trial area received approximately 4.8 ML of irrigation. Applied water was recorded on a water meter at
the bore and tensiometers were used to monitor soil moisture. Irrigation scheduling was based on weekly
pan evaporation and crop factors. The crop was planted in a full profile of moisture and received 10.0 mm of
irrigation to enhance germination and activate the herbicide. Intermittent showers in late March and early
April reduced the need for irrigation until 9 April. Irrigation continued until 12 July, 109 DAS at which time the
crop was physiologically mature. Crop water requirement will vary each year depending on time of planting,
cultivar, amount of residual soil moisture and seasonal evaporative demand.
Figure 9. Jetfill® tensiometer used to assist in scheduling irrigation for maize
60
Irrigating crops on light soil without monitoring equipment requires a degree of “guess work”. It is difficult to
determine the depth of water infiltration as water and nutrients can be pushed beyond the root zone. Using
pan evaporation is only partially accurate as evaporation rates can vary widely over a few days. With wide
fluctuations in evaporative demand it is difficult to maintain optimum irrigation schedules. In practice, relying
solely on pan evaporation often leads to under-or-over-watering, which results in a reduction in yield and/or
an increase in the cost of production.
Summary
The 1999 maize evaluation demonstrated that commercial hybrids are capable of producing 9.0 to 10.0 t/ha
on Blain soils under irrigation in the Daly Basin. Pioneer 3237 achieved almost 11 t/ha which was not
significantly different from DK 689, Hycorn 75 or 31M10. Pacific 338 had a significantly lower yield due to
poor establishment, demonstrating the need to have optimum plant populations for viable yields.
Populations of 70 000 to 80 000 plants/ha are adequate for optimum yields of the varieties evaluated. There
was no advantage in increasing the seed rates beyond that recommended by seed companies.
The N deficiency (caused by uneven fertiliser distribution at planting) demonstrated the need to have good
nutrition early in the crop’s life. This is particularly important for maize on light soils. Zn and B applications
prevented some of the nutrient disorders commonly seen in maize grown on sandy soils in the Douglas Daly
region in the past.
Insect pressure in 1999 was high and is a major concern. The incidence of leafhoppers, GVB, armyworms
and heliothis is a threat to the viability of commercial maize production unless effectively managed. WEV is a
serious threat and an effective, integrated pest management strategy should be developed.
Water management and water use efficiency was adequate in 1999 but could be improved with the use of
soil moisture sensors.
DRY SEASON 2000

The maize trial was repeated in 2000 using the best performing varieties of 1999 plus Hycorn 90, 32P75,
Cracker Jack, Genex 2 and Pacific 53IT. Eleven hybrids were planted on 28 April 2000 on Circle 2 centre-
pivot at DDRF in a randomised complete block. Only one population was evaluated. A Nodet Gougis
precision, vacuum planter (Figure 1) was used instead of the Mason Maxi Strike planter. The planter has the
capacity to band fertiliser beneath and to the side of the seed. This ensured that nutrients were available
immediately and eliminated the nutrient deficiency which occurred in 1999. A basal fertiliser was banded at
planting at the rate of 100.0 kg/ha consisting of 9.0 kg N, 19.0 kg P, 10.0 kg S, 2.5 kg Zn and 2.5 kg Cu/ha.
A plant population of 86 000 plants/ha was established at a row spacing of 75 cm. The crop received
approximately 250, 40, 150, 81 and 15 kg/ha of N, P, K, Mg and Zn, respectively in total. Soil water and
irrigation applications were monitored with “Jet-Fill” tensiometers set at 15, 30, 45 and 60 cm.
Insect control was carried out on five occasions. Two Rogor® (0.5 L/ha of 400.0 g/L a.i. dimethoate) and
one Lannate® (1.5 L/ha of 225.0 g/L a.i. methomyl) treatments were applied between week three and week
five to control leafhoppers and prevent WEV. Armyworms, heliothis and GVB were present in high numbers
at silking. Two aerial applications of insecticide were carried out, one prior to silking and one during silking.
Rogor® (800.0 mL/ha of 400.0 g/L a. i. dimethoate) and Lorsban® (2.0 L/ha of 300.0 g/L a. i. chlorpyrifos)
were tank mixed and applied by helicopter on 10 July to control a heavy infestation of GVB, Helicoverpa
spp. and armyworms during pollination. The trial crop was harvested with the same commercial header as in
1999.
61
Figure 10. A Nodet Gougis vacuum planter, capable of banding fertiliser below and beside seed

All varieties established well. Banding fertiliser below and to the side of the seed improved the nutrient
status, appearance and early vigour of the maize. There were no visible nutrient deficiencies.
Leafhoppers required control on three occasions due to the high numbers and the speed of reinfestation.
GVB adults, nymphs and egg rafts were evident in the crop throughout the season. GVB populations can
increase rapidly in the presence of Cavalcade, which is a host of GVB in the district. Once Cavalcade is
harvested in April and May, GVB migrate to maize and other irrigated crops. It is interesting that GVB were in
higher numbers in the maize crop than in the adjoining peanut crop. Due to the high numbers of insects the
trial area was sprayed with a combination of Rogor® (800.0 mL/ha of 400.0 g/L a. i. dimethoate) and
Lorsban® (2.0 L/ha of 300.0 g/L a. i. chlorpyrifos) at silking time to try and prevent damage to reproductive
parts.
Table 7. Insect pests on irrigated maize at DDRF, 2000
Insect pest Growth period and damage

Leafhoppers (various) (Cicadulina bimaculata) From emergence through to week 5 or 6. Hoppers
Possibly Chiasmus sp. and Orosius sp. transmit ‘wallaby ear’ i.e. stunting and distortion and
thickening of leaf and veins.
Armyworms (Mythimna separata) Late vegetative stage to silking. Defoliate plants and
may damage flag leaf and silks.
Green vegetable bug (Nezara viridula) Heavy infestations cause distortion of cobs and
damage to individual kernels.
Heliothis (Helicoverpa amrigera/punctigera) Damage to silks and cobs.
Prior to the application of Rogor® and Lorsban® in July the crop appeared to be in excellent health with no
apparent disorders. After spraying, it was apparent that normal pollination was not occurring (Figures 12 and
13). A large proportion of plants in all varieties produced multiple and partially-pollinated ears. Stem
distortion was also evident and some plants produced up to five barren ears. The severity of damage varied
throughout the varieties and no distinct pattern could be identified.
The damage to each variety in each replication was rated on the number of plants with partially- pollinated
cobs. The two earliest varieties (32 P75 and X32 J55) and one of the latest maturing varieties (Pioneer 3237)
had the highest yields and the least amount of damage. These varieties may have escaped the effect of the
62
chemical while the intermediate flowering lines had more damage and lower yields. Figure 11 shows that the
varieties with the lower degree of damage produced the best yields.
The exact cause of the damage and poor pollination has not been ascertained. One possibility is that the
combination of Rogor® and Lorsban® applied at tasselling reduced the viability of the pollen, damaged the
silks or physiologically interfered with the fertilisation process. Another is that the spray vat was
contaminated with herbicide. Information was sought from maize specialists in Australia and the US but no
satisfactory explanation could be found. Insecticides are regularly used in sweet corn crops during silking
with no phyto-toxic effects reported. Avoiding the use of insecticides at silking may prevent such
occurrences.
Maize Variety Evaluation DDRF Dry Season 2000
10000 100.00%
9000 90.00%
8000 80.00%
7000 70.00%
Percent Plant Damage (visual)

6000 60.00%
Yield (kg/ha)
5000 50.00%
4000 40.00%
3000 30.00%
2000 20.00%
1000 10.00%
0 0.00%
75 26
9 17 90 42
4
ac
k x2 68
9
P7
5 37 35
rn 53 rn rJ ne 32 2J
co PA
C C co PA
C
ke Ge DK 32 er X3
Hy PA Hy ac ne
Cr Pio
Varieties
Yield (kg/ha) Percent Damage
Figure 11. Yield and proportion of physiological damage in maize varieties in 2000
Variety performance
The crop was harvested on 3 September 128 DAS. Yields in 2000 were reduced as a result of the
physiological damage and the incomplete pollination. In 1999 the site mean yield was 9.4 t/ha. In 2000 it was
only 6.8 t/ha, a 28% reduction from the previous year. The yields are presented in Table 8. No statistical
analysis was undertaken due to the variable damage throughout the trial.
63
Figures 12a and b. (left) Characteristic stem bending evident in 2000. (right) Un-pollinated ear. The damage
coincided with an insecticide application between tasselling and at silking.
Figures 13a and b. (left) GVB nymphs on maize and (right) typical cob distortion caused by bugs feeding on
outer kernels
64
Table 8. Maize variety yield, 2000
Variety Name t/ha

12% moisture
1 PAC 442 6.8
2 Hycorn 75 4.2
3 Hycorn 90 6.8
4 DK 689 7.2
5 PAC 269 4.2
6 Pioneer 3237 8.8
7 X32 J55 8.9
8 32 P75 8.0
9 Cracker Jack 6.9
10 Genex 2 7.1
11 PAC 53IT 5.6
Mean 6.77
Average machine harvested yield from 4 replications
Summary
The 2000 trial had a high level of insect infestation as in 1999 and required multiple insecticide applications.
The level of control required will reduce the economic viability of maize production unless alternative cost-
effective pest management strategies are employed. The 2000 trial identified a possible hazard with trying to
control insects at pollination. The chemicals or their combination (Rogor® and Lorsban®) while not
conclusively proven, may have interfered with the pollination process and reduced yield. The other possibility
is herbicide contamination of the spray vat. The frustrating aspect is that the cause of the damage remains
unknown.
The positive aspect of the 2000 trial was the success of banding fertiliser below the seed at planting time
which resulted in improved uniformity, early vigour and enhanced the nutritional status of the crop. There
were no visible nutritional disorders in the 2000 crop and N status at 20 DAS was within the recommended
range i.e. 3.5 to 5% N.
Improving pest management in irrigated maize production is a high priority.
DRY SEASON 2001

Nine commercial varieties of maize were sown in a conventionally prepared seedbed under the centre pivot
at DDRF on 10 April 2001. The varieties and yields appear in Table 1 and Figure 3. The trial crop was
planted with a Nodet Gougis vacuum planter with basal fertiliser banded beneath the seed. Mungbeans (cv
Putland) were grown during the previous wet season and ploughed in prior to planting. The trial was a
randomised complete block with four replicates, with plots 150 m long by four rows. The plots were
surrounded by maize to protect the trial crop from bird damage. The total planted area was approximately 5
ha. Leaf samples were taken 35-40 DAS and at silking to determine nutritional status. Hand harvests were
taken and total plot yield was measured using a commercial International 1420 header.
Fertiliser was applied pre-planting, at planting (banded) and by fertigation. The trial crop received 250.0 kg
N, 40.0 kg P, 150.0 kg K, 33.0 kg S, 64.0 kg Mg, 20.0 kg Zn and 1.5 kg B. The established plant population
was between 75 000 and 84 000 plants per/ha (recommended by seed companies) at a 75 cm row spacing.
65
An Enviroscan® soil moisture sensor and Jet-Fill® tensiometers were used to monitor irrigation and soil
moisture content. The crop received approximately 5.0 ML/ha of water. Weeds were controlled by a post-
planting, pre-emergent application of Primextra® at 5.0 L/ha (277 g/L a.i. metolachlor and 223 g/L a.i.
atrazine).
An Insectigator III® chemigation unit (Figure 1) was installed on the centre pivot in 2001 to evaluate the
efficacy of pesticides applied through the irrigation water. The unit injects precise amounts of chemical
directly into the irrigation water. A non-return valve was fitted to the delivery line at the pivot to prevent back-
flow and chemical entry into the supply line.
Figure 14. Insectigator III® chemigation unit showing tank and pump
In 2001 Gaucho® (imidacloprid), a systemic seed dressing in the nitroguanidine group of chemicals, was
evaluated for the control of leafhoppers and WEV. Gaucho® is a low-toxicity chemical which was introduced
in 1997 and has been successfully used in cotton to control thrips, aphids and wireworms. All of the varieties
were treated with Gaucho®. An untreated (un-replicated) observation area was established adjacent to the
main trial to compare the effect of Gaucho® on leafhopper numbers.
Seed treatments reduce the amount of chemical needed, act specifically on pests, are safe to beneficial
insects and reduce the need for handling and spraying insecticides. Gaucho® -treated seed is available from
seed companies for the control of a range of soil insects and sucking pests.
Soil moisture was monitored using an Enviroscan® soil moisture sensor (Figure 2). An Enviroscan® is a
capacitance sensor which continuously measures volumetric soil moisture at defined depths in the profile.
66
The measurements are stored in a data logger which is down-loaded to a computer software package.
Graphs are generated which show soil water content, drainage and crop water use (Figures 18 and 19).
Figure 15. Installing an Enviroscan® soil moisture monitoring probe

Analysis of variance showed a significant difference between varieties. Q81 yielded significantly less than all
other varieties. Yields from DK 689, (which averaged nearly 11 t/ha), Pacific 424, Hycorn 75 and Pioneer
3335 were not significantly different. Most of the other varieties (excluding Q81) did not differ significantly
from Pioneer 3335, which had a yield of over 10.0 t/ha.
Hand-harvests produced yields of over 14.0 t/ha in some varieties but on average machine harvested yields
were 22% lower. This highlights the importance of large machine harvested plots in assessing the true
commercial potential of a particular crop. This trial indicated that many commercial varieties are capable of
producing 10 t/ha on Blain soil in the Top End. DK 689, Pioneer 3237 and Hycorn 75 have provided
consistently high yields over the past three years.
Lodging was visually rated from 1 to 5 (i.e. from mild to severe). Cracker Jack had the highest lodging score
of 2.6 followed by DK689 and Pioneer 3237 at 1.63. Most of the other varieties had low ratings for lodging.
67
Table 9. Variety yields, 2001
Varieties Hand-harvested Machine-harvested Difference between

yield (kg/ha*) yield (kg/ha) hand and machine
harvested yields (%)
Pac 53IT 12.9 9.59 25.7
Hycorn 75 13.1 10.79 17.6
Pac 424 14.2 10.86 23.5
Pioneer 3335 12.1 10.19 15.8
Pioneer 3153 14.3 9.54 33.3
Q 81 9.9 7.60 23.2
Cracker Jack 11.9 9.71 18.4
Pioneer 3237 13.3 9.61 27.7
DK 689 12.9 10.99 14.8
Site mean 12.7 9.87 22.3
*Yield is the average weight from ten hand harvested plants from each replication converted
to t/ha
Yield Grain Weights
14.00 100.0
12.00 95.0
Grain Weight (kg/100L)

10.00
90.0
Yield (t/ha)
8.00
85.0
6.00
80.0
4.00
2.00 75.0
0.00 70.0
Hycorn Pioneer Cracker Pioneer Pioneer
DK 689 PAC 424 PAC 53IT Q 81
75 3335 Jack 2 3237 3153
Yield 10.99 10.86 10.79 10.19 9.71 9.61 9.59 9.54 7.60
Grain Weights 78.9 77.6 80.2 78.3 83.7 81.2 75.1 81.0 75.8
Variety (2001)
Figure 16. Yield and grain weights for 2001 maize variety evaluation at DDRF at 95% confidence intervals
Gaucho® effectively controlled leafhoppers and WEV. The non-treated area was severely affected by WEV,
where plants were stunted, had shorter stalks, smaller leaf area and poor root development. The treated
area had a lower number of leafhoppers and no visible disease symptoms. Gaucho® eliminated the need to
apply insecticides for leafhopper control in 2001 whereas three chemical applications were required in
previous seasons. Yield from the affected area varied from 2.6 to 5.8 t/ha compared with an average of 9.8
t/ha from the treated area (Table 10).
68
Table 10. Effect of Gaucho® on leafhopper numbers
Control Gaucho-treated
(non-treated)
Leaf-hopper numbers 94 5
(insects /10m row*)
Yield 2.6**to 5.8 t/ha 9.8 t/ha
mean of all treated varieties
*Average number from multiple vacuum samples from 10 m row
**Yield from the most severely affected area
The Insectigator III® chemigation unit was used to apply insecticides and biocides to control a range of
pests. Gemstar® at 500 mL/ha (a. i. Nuclear Polyhedrosis Virus) and DiPel Forte at 500 g/ha (a. i. Bacillus
thuringienesis var kurstaki) were applied to control armyworms and Helicoverpa spp. Gemstar® appeared
(observation only) to be more effective in reducing larvae numbers than Dipel®. Biological insecticides need
to be applied when the larvae are very small. Monitoring and identification of eggs and small larvae is
necessary to determine the optimum time for application.
GVB infested the crop in large numbers. Dipterex® at 1.1 L/ha (500 g/L trichlorfon a.i.) was applied prior to
silking and Decis Options® (synthetic pyrethroid) was applied at 2.5 L/ha (deltamethrin 27.5 g/L a.i.) at early
grain fill to control Helicoverpa sp. GVB.
The combination of Gaucho® and chemigation was more efficient and cost effective in reducing pest
populations and disease than applying chemicals either by ground-rig or by aircraft.
Figures 17a and b. (a) Maize (top right hand corner) was Gaucho® treated and grew normally. Maize in
foreground (un-treated) and was stunted by WEV. (b) Plants on the left were treated with Gaucho® and
show normal growth. Stunted plants (un-treated) on the right are the same age and cultivar and severely
affected by WEV.
69
An Enviroscan® moisture meter was used to monitor soil water in the 2001 season. Moderate evaporation
rates in April and May, low soil-moisture holding capacity and low initial crop water demand dictates that the
crop receives frequent but light irrigations. A schedule of 15.0 mm of water was applied about every three
days (i.e. 35.0 mm/week) for the first six to seven weeks. This kept the soil surface and upper profile moist to
enhance rapid and uniform germination. Moisture gradually drained down to 70.0 cm by week four (Figure
18) and to 100.0 cm by week five (Figure 19). This indicated that the water application was heavier than the
rate of crop uptake. However, lighter or less frequent irrigations risked drying of the seed-zone which may
have affected crop emergence.
The Enviroscan® graphs showed that by week four to six the maize was extracting water from 70 cm. There
was also evidence of root activity at 100.0 cm (Figure 19). Between weeks 4 and 5 the crop began to rapidly
use moisture from the 40.0 to 70.0 cm depth. This period coincides with rapid plant development and when
the number of kernels and the size of the ear is being determined. By week six the crop had largely used
most of the moisture from below 40.0 cm and there appeared to be little root activity below this zone.
At week seven the irrigation schedule was increased 20.0 to 25.0 mm applied every four days (i.e. 35.0 to
43.0 mm/week) in line with crop water requirements. This was sufficient to keep the profile full to 40 cm
without causing drainage to lower levels. By late May the Enviroscan® showed there was little moisture
available for extraction between 50.0 and 70.0 cm. However Figure 19 shows that there was some water
extraction at 100.0 cm during week 6 to 9 while moisture was available at this depth. After week 9 there
appeared to be little root activity at 100 cm due to declining moisture availability. From late May onwards, the
majority of active water extraction was in the 10.0 to 40.0 cm zone where there was ample soil moisture
available.
From July to August irrigations were reduced to 20.0 mm every five days (28.0 mm/week) as the crop
approached maturity. The crop received approximately 5.0 ML of water for the season giving an average
water use efficiency (WUE) of 1.96 t/ML. This equates to 19.6 kg of grain/mm of water applied which
compares favourably with figures in the literature of 16.0 to 18.0 kg of grain/mm of water applied (Brown
1997).
The Enviroscan® assisted in scheduling irrigation more accurately and prevented moisture and nutrients
being leached below the root zone. Learning to install and interpret soil moisture data accurately is critical in
using monitoring equipment and improving water management. The graphs illustrated that the early irrigation
was probably too heavy (resulting in drainage to 100.0 cm), while the schedule in the middle of the season
was probably too light (depletion of the 50.0 to 70.0 cm zone). One or two heavier irrigations in June would
have improved moisture availability lower in the soil profile, decreasing the risks of moisture stress.
70
Active moisture extraction

at 50 to 70 cm 4 to 6 weeks
after planting.
Figure 18. Enviroscan® readings from 10.0 to 70.0 cm levels in the 2001 maize trial
Sensor showing
drainage to 100 cm
in week 6 to 7
Figure 19. Enviroscan® readings for 20.0, 40.0 and 100.0 cm levels
71
Summary
The 2001 trial confirmed that commercial maize hybrids are capable of producing yields in excess of 10.0
t/ha on light soils in the Katherine-Daly basin. Four varieties produced over 10.0 t/ha and the combined trial
averaged 9.8 t/ha.
The systemic seed dressing and chemigation greatly improved pest management and reduced overall
chemical usage. Gaucho® provided excellent control of leafhoppers and WEV and eliminated the need for
insecticides in the early vegetative period. Chemigation proved successful in controlling pests during
tasselling and grain fill, and eliminated the need for aerial application. The efficacy of Gemstar®, Dipel® and
similar products needs further evaluation under NT conditions. Unfortunately, these products do not control
GVB, which can be a serious pest in irrigated maize.
Irrigation scheduling in 2001 was improved by using an Enviroscan® and a high WUE was achieved.
However, allowing the profile to dry below 40 cm means there is no reserve of soil moisture at depth. Filling
the profile to 60.0 to 80.0 cm, prior to silking and pollination will ensure moisture is available during the
critical growth phase and will reduce the risk of moisture stress if something goes wrong with the irrigation
system. Maintaining good soil moisture in the lower profile is desirable but difficult to achieve in light soils of
high permeability. Due to the low water holding capacity of Blain soils, water which is not taken up by plants,
will drain to lower levels in the profile and eventually pass beyond the root zone.
Moisture meters will certainly assist in fine tuning irrigation schedules on light soils.
DRY SEASON 2002

Four of the most consistent varieties from previous trials (DK 689, Pioneer 3153, Pioneer 3237 and Hycorn
424), three new commercial varieties (Hycorn 449, Hycorn 901and Pacific 675) plus an experimental variety
(Pioneer X1180) were evaluated in 2002. The trial was sown into a conventionally prepared seedbed on 26
March using a Nodet Gougis precision vacuum planter. A mungbean green manure crop (cv. Putland) was
grown over the wet season and ploughed in, four weeks prior to sowing. The average plant population over
the trial was 69 642 plants/ha with a low of 65 000 and a high of 74 600 plants/ha.
The trial was a randomised complete block with three replicates and plot sizes of 120.0 m long, by eight
rows. The trial crop was harvested on 6 September, 164 DAS. The trial was harvested with an International
1420 header.
An Enviroscan® was used to monitor soil moisture content and assist in irrigation scheduling. The crop
received approximately 5.5 ML/ha of water. Weeds were controlled by a post-plant, pre-emergent application
of Primextra® at 5.0 L/ha.
An Insectigator III® chemigation unit was used to apply insecticides and biocides to control armyworms,
Helicoverpa spp. and GVB. A low tolerance of insect pressure was maintained to ensure maximum yield.
Lorsban® was applied pre-tasselling and Dipel® and Gemstar® were applied during pollination to control
armyworms and Helicoverpa larvae. Seed was treated with Gaucho® to control leafhoppers and WEV.
Fertiliser was applied pre-plant, at planting (as a band beside and below the seed) and through the
fertigation system. A total of 330.0, 40.0, 250.0 and 30.0 kg/ha of N, P, K and S, respectively was applied
during the life of the crop. Mg, Zn and B were also applied at the rate of 50.0, 5.0 and 1.5 kg/ha, respectively.
72

Yields in 2002 were higher than in the previous three seasons (Figure 1). Lower insect pressure, improved
varieties and increased N and water may have contributed to higher yields in 2002.
The average yield of all the varieties was 11.7 t/ha. Pacific 675, yielded 12.7 t/ha and was significantly better
than all varieties except Pioneer 3237. Hycorn 449 gave a significantly lower yield than the other varieties
but still produced 10.0 t/ha. There were no significant differences in yield between Hycorn 901, Hycorn 424,
DK 689, Pioneer 3237, Pioneer X 1180 and Pioneer 3153. Yields are presented in figure 20.
The crop received 5.5 ML/ha of irrigation in 2002 compared with about 5.0 ML/ha in 2001 in spite of being
planted two weeks earlier than the 2001 crop. Pre-plant watering was carried out to fill the top 30.0 cm of the
soil and to promote good germination. Irrigation rates were on average higher than in 2001 to allow moisture
to penetrate to below 50 cm. Despite the increased water usage in 2002, WUE was marginally higher at 2.12
t/ML (21.2 kg/mm) compared to 1.96 t/ML (19.6 kg/mm) in 2001.
Based on the average site yield of 11.7 t/ha, the crop (including stover) took up a total of 266.0 kg/ha of N,
31.0 kg/ha of P, 183.0 kg/ha of K, 15.0 kg/ha of S and 0.4 kg/ha of Zn. Between 190.0 and 207.0 kg/ha of N
was taken up in the maize grain, depending on variety and yield.
Hand harvests were taken from different populations in the surrounding bulk area to estimate potential silage
yields. Table 16 lists a range of plant populations with corresponding oven-dry weights. Weights were
converted to an equivalent silage yield (t/ha) at 40% dry matter (DM). While no conclusion can be drawn
(due to the small sample) biomass increased with increasing plant densities up to a maximum population of
170 000 plants/ha. Populations over 80 000 plants/ha is likely to give optimum dry matter yields. However,
plant population for silage production will depend on agronomy, planting time, variety, soil type, row-spacing
and many other variables. Commercial companies will recommend optimum population for specific varieties
and uses.
Yield Grain Weights
16.00 100.0
14.00
95.0
12.00
90.0 Grain Weight (kg/100L)
10.00
Yield (t/ha)
8.00 85.0
6.00
80.0
4.00
75.0
2.00
0.00 70.0
Pioneer Pioneer Pioneer
Pac 675 Hycorn 424 Hycorn 901 DK 689 Hycorn 449
3237 3153 X1180
Yield 12.74 12.17 11.97 11.82 11.65 11.59 11.51 10.07

Grain Weights 79.8 79.8 81.0 77.3 79.5 82.3 79.3 83.2
Variety (2002)
Figure 20. Yield and grain weight for the 2002 maize variety evaluation crop at DDRF, at 95% confidence
intervals
73
Table 11. Hand harvest biomass yields of irrigated maize 2002, DDRF
Average plants/ha Total oven dry biomass Equivalent silage yield (t/ha)
(t/ha) (40% DM)
170 000 24.5 61
156 660 23.6 59
140 000 20.6 51.5
86 664 20.3 50
83 331 19 47.5
81 664 21.2 53
73 331 18.1 45.3
61 665 18.33 45.8
Irrigated Maize Plant Populaton v's Biomass at

DDRF 2002
180,000 30
160,000
25
140,000
Oven Dry Wt.
120,000 20
Plants/ha
100,000 Plants/ha
15
80,000 Biomass (t/ha)
60,000 10
40,000
5
20,000
0 0
Figure 21. Plant population and oven dry yield (t/ha) of irrigated maize at DDRF in 2002
Resistance to lodging, stem strength and resistance to disease are important aspects of maize production in
the tropics. Maize stalks tend to collapse relatively quickly after physiological maturity. Lodging is usually
more severe in thin stalked varieties.
Lodging was not severe in 2002. However, varieties Pac. 424 and DK 689 tended to lodge more than other
varieties in previous years. Pioneer X1180, Pioneer 3153 and Pacific 675 have thick robust stalks and are
less likely to lodge. High daytime temperatures and moisture (from dews) seems to exacerbate the
breakdown of stem material under tropical conditions.
Conclusion
The four year evaluation indicated that maize yields of 9.0 to 12.0 t/ha are achievable on Blain soils. The
evaluation highlighted the need to get the nutrition, pest management and water scheduling right in maize
production. In 2002 when nutrition, water and insect pests were well managed, yields approached 13.0 t/ha
for the best varieties. The average yield for all varieties over four years was 9.3 t/ha. Excluding the 2000
74
season results (crop damage and incomplete pollination), the average yield for all varieties and for the best
four varieties was 10.3 t/ha and 11.0 t/ha, respectively.
Higher yields may be possible on heavier clay loam (Tippera) soil types due to better moisture and nutrient
retention, and good commercial yields have being reported on clay-loams at Katherine.
The trial also highlighted the importance of larger scale, machine-harvested plots in determining commercial
potential. Small plots are useful for direct varietal comparison, but give artificially high estimates of field
performance. Information provided to growers and agribusiness needs to be based on realistic and
achievable yields obtained from commercial sized trials.
Varieties DK 689, Hycorn 75 and Hycorn 90 have been replaced by new lines. New hybrids are continually
being developed and will need to be evaluated prior to broad-scale plantings in the NT. At the time of writing,
varieties which could be recommended include Pioneer 3237, Pioneer 3153, Hycorn 424, Hycorn 901
(replaces Hycorn 90) and Pacific 675 (replaces Hycorn 75).
Insect and disease management are high priorities in irrigated maize in the NT. Leafhoppers and WEV are
the biggest economic threat. However, Gaucho® effectively controlled the insect vector in this evaluation.
Dry season maize seed should be treated with Gaucho® or an equivalent registered systemic chemical.
Other systemic seed treatments should be evaluated for leafhopper control and other insect pests.
Armyworms, heliothis and GVB have the potential to cause economic damage. Crops may require
insecticide treatment if pests reach threshold levels. Chemigation has proven effective and eliminates the
expense of aerial application. Chemigation allows more precise timing of pesticide application which is the
key to controlling insects. It also allows the use of ‘softer’ control options such as Gemstar®, which targets
caterpillar pests while minimising the impact on beneficial insects. However, chemigation must be carried out
in accordance with the relevant legislation and only with chemicals which are registered for the purpose.
Birds, pig and wallaby damage is a major consideration in isolated crops especially near river systems. The
trial area was protected from pigs and wallabies but damage from sulphur crested cockatoos occurred.
Cockatoos completely strip cobs but generally concentrate on the edge, gradually eating their way in. Pigs
damage much more than they consume and pig-proof fencing will be required in many areas.
Maize is an expensive crop to produce in the NT due to high fertiliser, freight and fuel costs. Optimum plant
populations, adequate water and nutrition, good weed, insect and disease management and adapted high
yielding hybrids are the keys to viable maize production. Maize will only be viable at the highest levels of
production.
Further R&D is needed to refine water and nutrient use in maize in the tropics. The N contribution of green
manure and legume rotation crops should be quantified, as N constitutes one of the highest production
costs. Identifying varieties with greater yield potential and pest and disease resistance will also enhance the
crop’s viability.
Insect pests are a constant threat in tropical farming systems. Developing effective integrated pest
management systems for maize and other irrigated crops and keeping abreast of new developments in crop
production, nutrient and water management is imperative for long term sustainability.
75
REFERENCES
Allen, R. G., Pereira, L. S., Raes, D. and Smith, M. (1998). Crop evapotranspiration – Guidelines for
computing crop water requirements. FAO Irrigation and Drainage Paper 56. FAO Food and Agriculture
Organisation of the United Nations, Rome.
Anon. Pioneer Hi-Bred Australia Maize Workshop. Growing maize for profit. Pioneer Hi-Bred International
Inc. Toowoomba, Qld.
Anon. (2004). Crop Management Notes. Summer 2004 Edition. Department of Primary Industries and
Fisheries, Primary Industries Building, 80Ann St, Brisbane, Queensland, Australia.
Anon (2004). Maize Diseases: A Guide for Field Identification: 4th Edition. The CYMMYT Maize Program.
International Maize and Wheat Improvement Centre, Carretera -Veracruz, El Batan, Texcoco, Edo CP 56130
Mexico.
Anon (2005). Clearfield® production system: Advanced Technology, Global Acceptance. BASF Corporation.
Anon. (2005). Pacific Seeds Hybrid Corn Agronomy Guide 2005. Pacific Seeds Pty Ltd.
Anon. (2006). Corn 2006 Pioneer Brand Seeds. Pioneer Hi-Bred International Inc.
Anon. (2006). Maize: NSW planting guide 2006-07. NSW DPI Primefacts. Primefact 267. NSW Department
of Primary Industries.
Anon.(2006). Pacific Seeds Hybrid Corn Agronomy Guide 2005. Pacific Seeds Pty Ltd
Airey, D. R. (1972). Maize: Development and Research in the Northern Territory. Technical Bulletin. Animal
Industry and Agriculture Branch. Northern Territory Administration, Darwin.
Aldrick, J. M. and Robinson, C. S. (1972). Report on Land units of the Katherine – Douglas Area, NT 1970.
Land Conservation Series No 1 1972. Land Conservation Section, Animal Industry and Agriculture Branch,
Northern Territory Administration, Darwin NT.
Arndt, W., Phillips, L .J., and Norman, M. J. T., (1963). Comparative Performance of Crops on Three Soils of
the Tipperary Region, NT. Division of Land Research and Regional Survey, Technical Paper No: 23
Commonwealth Scientific and Industrial Research Organisation (CSIRO) Melbourne, Australia.
Brier, H., Mills, G., McLennan, A., Lucy, M., and Wessels, J. (2004) Insects: What soybean insect is that?
Queensland Department of Primary Industries and Fisheries GPO Box 46 Brisbane Qld 4001.
Browne, R. (1997). Australian Maize. Kondinin Group PO Box 913 Cloverdale, Western Australia 6105.
Carberry, P. S., Chapman, A. L., Anderson, C. A., and Muir, L.L. (1996). (Eds.). Conservation tillage and Ley
Farming Systems for the Semi-Arid Tropics Australian Journal of Experimental Agriculture Volume 36 No.8
1996.
Cohen, B.R. (2007). Biotech to Ease Ethanol-Related Corn Shortage. Environment News. The Heartland
Institute. www.heartland.org
Dilshad, M., Motha, J. A., and Peel, L. J. (1994). Preliminary Assessment of the Influences of Pasture Cover
on Surface Runoff, Bedload and Suspended Sediment Losses in the Australian Semi Arid Tropics. Technical
76
Memorandum No. 94/12 Conservation Commission of the Northern Territory. PO Box 496. Palmerston NT
0831 Australia.
Dilshad, M., Motha, J. A., and Peel, L. J. (1996). Surface Runoff, soil nutrient losses from farming systems in
the Australian semi-arid tropics. Australian Journal of Experimental Agriculture Volume 36 No.8 1996
Garside. A. L. and Price, T. P. (1984). Report on ADMA Farm Monitoring 1983/84. Internal Reports on Pilot
Farms in the Douglas Daly Region. NT Department of Primary Production Darwin.
Hausler, P. A. Maize in the Northern Territory (unpublished). NT Department of Primary Industry, Fisheries
and Mines GPO Box 3000 Darwin NT 0801.
Herman, J. C., (1996). (Ed). How a Corn Plant Develops: Special Report No. 48. Iowa State University of
Science and Technology Cooperative Extension Service, Ames, Iowa USA.
Hoeft, R. G., Nafziger, E. D., Johnson, R. R., and Aldrich, S. R. (2000). Modern Corn and Soybean
Production. First Edition. MCSP Publications 1520 Yorkshire Dr. Champaign, IL 61822.
Isbell, R. F. (2003). The Australian Soil Classification. CSIRO Publishing. P.O. Box 1139, Collingwood,
Victoria, Australia.
Kaiser, A., Colless, J., Lawson, J. and Nicholls, C., (1997). Australian Maize. Kondinin Group PO Box 913
Cloverdale, Western Australia 6105.
Lucas, S. J. (1983). Land Units of the Douglas-Daly ADMA Acquisition Area. NT. Technical Report No 10:
Conservation Commission of the Northern Territory.
Miller, W.R., and Donahue, R.L., (1990). Soils: An Introduction to Soils and Plant Growth. Sixth Edition.
Prentice Hall, Inc. Englewood Cliffs, New Jersey 07632.
Muchow, R. C. (1989). Comparative productivity of maize, sorghum and pearl millet in a semi-arid tropical
environment. I. Yield Potential. Field Crops Research 20,191-205
Muchow R. C. (1989). Comparative productivity of maize, sorghum and pearl millet in a semi-arid tropical
environment. II. Effect of water deficits. Field Crops Research 20, 207-219
Muchow, R. C. (1985). (Ed.). Agro-Research for the Semi-Arid Tropics. CSIRO Division of Tropical Crops
and Pastures, Darwin Laboratories NT. University of Queensland Press, PO Box 42, St. Lucia, Queensland
Australia.
Murti, S. (2002). Economic Evaluation of Irrigated Peanut Production in the Northern Territory. Internal
Report. Department of Primary Industry, Fisheries and Mines, Berrimah Farm, Makagon Road Berrimah, NT.
GPO Box 3000 Darwin NT 0801
Northcote, K. H. (1979). A Factual Key for the Recognition of Australian Soils, Fourth edition Rellim Tech.
Publ., Glenside, South Australia.
O’Gara, F. P. (1998). Striking the Balance: Sustainable Farming for the Semi-arid Tropics of the Northern
Territory. Department of Primary Industry, Fisheries and Mines, Berrimah Farm, Makagon Road Berrimah,
NT. GPO Box 3000 Darwin NT 0801
77
Paliwal, R., Granados, L., Lafitte, G., Violic, H. R and Marathee, J. P. (2000). Tropical Maize: Improvement
and Production. FAO Plant Production and Protection Series No. 28. Food and Agriculture Organisation of
the United Nations, Rome.
Phillips, L. J. (1959). The Influence of Crop Sequence on the Yield of Peanuts, Sorghum and Cotton at
Katherine, NT. Division of Land Research and Regional Survey, Technical Paper No: 2 Commonwealth
Scientific and Industrial Research Organisation (CSIRO) Melbourne, Australia.
Plant, G. and Plant, M. (2001). Commercial Peanut Production in the NT. A Grower’s Experience. Technical
Bulletin 292. Department of Primary Industry, Fisheries and Mines, Berrimah Farm, Makagon Road
Berrimah, NT. GPO Box 3000 Darwin NT 0801
Price, T. P. (1983). Report on ADMA Farm Monitoring 1982/1983. Internal Reports on Pilot Farms in the
Douglas Daly Region. NT Department of Primary Production Darwin.
Roberts, A. (1986). Review of DPP Research 1954-1968. Technical Bulletin No.96 Agdex 111/09 NT
Department of Primary Production Darwin NT.
Reuter, D. J. and Robinson, J. B. (1997). (Eds.). Plant Analysis: An Interpretation Manual. Second edition.
CSIRO Publishing, PO Box 1139 Collingwood, Victoria 3066.
Schultz, G. C. and Garside, A. L. (1982). Report on ADMA Farm Monitoring 1981/82. Internal Reports on
Pilot Farms in the Douglas Daly Region. NT Department of Primary Production Darwin.
Sprague, G. F. (1977). (Ed). Corn and Corn Improvement. American Society of Agronomy, Inc., Madison,
Wisconsin, USA.
Stace, H. C. T., Hubble, G. D., Brewer, R,. Northcote, K. H., Sleemam, R.J., Mulcahy, M.J. and Hallsworth,
E. G. (1968) A Handbook of Australian Soils. Rellim, Adelaide, SA.
Sturtz, J. D. and Chapman, A. L. (1995). (Eds.) Conservation Farming for the Semi-Arid Tropics,
Proceedings of a Workshop at the NT Rural College, 18-20 July.
Summer Crop Management Notes 2004. Queensland Department of Primary Industries and Fisheries.
Primary Industries Building 80 Ann St, Brisbane, Queensland, Australia.
Thiagalingham, K., Gould, N. and Watson, P. (1991). Evaluation of the Effects o of Tillage, Rotation and
Nitrogen on Maize and Soybeans (1986-1987). Internal Report No.21 October 1991. Department of Primary
Industry and Fisheries, Northern Territory Darwin, NT.
78
Warren, J. (1982). Maize Hybrid Assessment on Cockatoo Sands under Sprinkler Irrigation (82 KU 32) in
Internal Research Report: 1982 Dry Season Agronomy Proceedings, Western Australia Department of
Agriculture, Kununurra.
79

TB 326

Uploaded by

Copyright:

Available Formats

TB 326

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TB 326

Uploaded by

Copyright:

Available Formats

IRRIGATED MAIZE PRODUCTION IN THE TOP END

OF THE NORTHERN TERRITORY

PRODUCTION GUIDELINES AND RESEARCH RESULTS

Technical Bulletin No. 326

Northern Territory Government

ISBN: 978 0 7245 4725 8

SELECTING A SUITABLE VARIETY

Variety Uses Maturity (days Resistance to Husk cover Average

SOIL TYPE AND LAND PREPARATION

Figure 2. Oolloo soil is a free draining sandy loam red earth

PLANT POPULATION, PLANTING RATE AND ROW SPACING

Desired plant Number of seeds/kg Average seed

2500 3000 3500 4000

Sowing rate (kg/ha) for

The following calculation can be used to determine the sowing rate:

Sowing rate = desired population ÷ seeds/kg ÷ germination% ÷ emergence%

• Sowing rate = seed planted (kg/ha)

Calculating seed spacing along the row

• Seed required = 32.6 kg

Distance between seeds = 0.11 m or 11 cm (each seed should be 11 cm apart)

• Optimum plant population is one of the most

• 70 000 to 85 000 plants/ha is optimum for most

• Narrow row spacings will assist in moisture

AVERAGE TEMPERATURE DATA FOR DDRF

March to August has the most

Figure 4. Mean, highest and lowest maximum temperatures at DDRF (1968-1999)

M E AN E VAP ORATION FOR DDRF

MEAN EVAPORAT ION

Period w hen evaporation is

Figure 5. Average daily evaporation at DDRF (1968-1999)

ARE TWO MAIZE CROPS PER YEAR POSSIBLE?

• Maize is a warm season crop and is not suited to

• Planting in early dry-season allows the crop to

• Mild day and night temperatures at pollination

• Two crops per year may be a possibility provided

• Previous cropping/fertiliser history

Figure 6. Maize growth periods and nutrient uptake

Figure 7. N deficiency (light stunted plants) due to uneven application of fertiliser

SULPHUR (S) AND MAGNESIUM (MG)

NUTRIENT AVAILABILITY AND SOIL PH

Applying acidifying fertilisers such as ammonium sulphate, mono-ammonium or di-ammonium phosphates

TIMING AND APPLICATION OF CROP NUTRIENTS

Figure 10. Schematic plan of fertiliser placement in relation to seed

Table 3. Nutrient uptake by maize crop (kg/ha)

• Maize has a high nutritional requirement

• The period from week six to week ten is the most

• Fertiliser inputs need to be balanced with soil fertility

• Optimum N and plant population are the keys to high

DISEASE AND INSECT CONTROL

OTHER MAJOR PESTS

Figure 15. Heliothis caterpillar

Figure 16. Green vegetable bug and eggs on maize

CHEMIGATION FOR PEST CONTROL

INTEGRATED PEST MANAGEMENT (IPM)

Table 4. Insect pests of irrigated maize in the NT

Insect pest Growth period and damage Comment and control

If there are one or more insects (or five

Adapted from QDPI&F Summer Crop Management Notes 2005

Table 5. Insecticides registered for use in maize