Separations and Reaction Engineering Design Project Production of Ammonia

Download as pdf or txt
Download as pdf or txt
You are on page 1of 10

Separations and Reaction Engineering

Design Project

Production of Ammonia

Your assignment is to continue evaluating the details of a process to produce 50,000


tonne ammonia per year from synthesis gas. This ammonia synthesis loop is to be
integrated with a larger process that converts coal into synthesis gas (syngas), adjusts the
composition of the syngas, and produces ammonia. Ammonia is one of the top five
commodity chemicals produced by the chemical industry. It is used as a raw material for
nitrogen oxides and fertilizers, among other products. As the final part of the feasibility study,
we would like you to study the details of the reactor and separation section of proposed plant
and then optimize the complete process. Your final design should be an optimized process
and should include all unit operations necessary to produce the desired amount and purity of
ammonia.

Chemical Reaction

To provide an initial guess for the integration of the ammonia synthesis loop into the
overall process, the syngas feed is assumed to have been pretreated to yield stoichiometric
amounts of nitrogen and hydrogen. The syngas is available at 1000 kPa and 200°C. The
syngas feed specifications are 24.4 mole % nitrogen, 73.3 mole % hydrogen, 2.3 mole %
methane, and 5.6 ppm carbon dioxide. In the pretreatment, oxygen-containing compounds
like CO​2 must be removed, because amounts above 10 ppm in the reactor poison the
catalyst. One method for accomplishing this is by methanation, hence the small amounts of
methane in the feed syngas. If carbon dioxide must be removed from the process feed,
monoethanolamine or diethanolamine (pure or dissolved in water) are recommended solvent
candidates for a scrubber. The solvent can be recovered by stripping. These amines may
require non-typical materials of construction.

The reaction is reversible and described by:

(1)

Detailed kinetics for the reaction are described in Appendix 2. The ammonia product stream
is to have an ammonia content of greater than 99.9 weight % as a liquid that can be pumped
to a nearby rail loading facility. For additional information on ammonia production, consult
the literature. Some possibilities are suggested.​1,2​ It is highly recommended that you read
about ammonia production before proceeding with this assignment. Many chemical prices
are available at​ ​http://www.icis.com/StaticPages/a-e.htm​. The value of syngas is $0.10/kg.

Specific Assignments
1. Separations Design – (ChE 312)

You are to determine the number of distillation columns required, their locations, their
sequence, and enough information for each column to determine their costs. The distillation
column that purifies the ammonia should be designed in detail. A detailed design of a tray
tower includes number of trays, tray spacing, diameter, reflux ratio, weir height, top and
bottom pressure specifications, and design of auxiliary equipment (heat exchangers, pump,
reflux drum, if present). A detailed design of a packed tower includes height, packing size
and type, and the same other specifications as in a tray tower. For all columns in this
project, you may assume that HETP = 0.6 m. For the distillation column, the better
economical choice between a packed and tray tower should be determined. For either a
packed or a tray distillation column, the optimum reflux ratio should be determined.

Note that a tower consists of a vessel with internals (trays or packing). The
constraints on a vessel are typically a height-to-diameter ratio less than 20. However, it is
possible to extend this ratio to 30 as long as the tower is less than about 3 ft (1 m) in
diameter. For larger-diameter towers, stresses caused by wind limit the actual height. Extra
supports are needed for a height-to-diameter ratio above 20, even for smaller diameter
columns. Therefore, there is a capital cost “penalty” of an additional 25% (only on the
vessel) up to a ratio of 25, and a “penalty” of an additional 100% up to a ratio of 30.

You must choose the operating pressures for each column subject to constraints of
operating temperature and available utilities. If vacuum columns are needed, pressure drop
becomes a significant concern. As an alternative to tray towers, packed towers with a
low-pressure-drop structured packing may be used. The packing factor as defined in
Wankat​3​, p. 336, is that for Koch Flexipac #2. Assume the HETP for the structured packing
to be 0.6 m (see the definition of HETP in Wankat​3​, p. 332, and the relationship between
HETP and ​HOG ​ in Equation (15.36) in Wankat​3​.), and that the pressure drop is 0.2 kPa/m
(0.245 inch water/ft).

2. Reactor Design – (ChE 325)

Several reactor types may be considered for use in this design. They are an
adiabatic, packed bed reactor (a series of these with interstage cooling, if needed), an
“isothermal,” packed bed reactor, and a packed bed reactor with heat exchange. An
“isothermal” reactor is defined here as one with a specified outlet temperature, not
necessarily the inlet temperature, and some form of heat exchange is needed to add or
remove the heat of reaction to maintain constant temperature. Chemcad will model the
entire reactor as “isothermal” at that temperature. It must be understood that this situation is
not physically realistic. In a reactor with heat exchange, the temperature along the length of
the packed-bed reactor is not constant. The temperature can be controlled by varying the
temperature and flowrate of the heat-transfer fluid, heat-transfer area, and the catalyst/inert
ratio. The suggested heat-transfer fluid is Dowtherm A™. If a heat-transfer fluid is used, it is
circulated in a closed loop through the reactor where its temperature is increased (if the
reaction is endothermic) or decreased (if the reaction is exothermic). Then, heat is added
(removed) from the fluid in a heat exchanger (or fired heater, if needed). The heat-transfer
fluid is then pumped back to the reactor. Properties of the Dowtherm A™ can be obtained
from Chemcad.

For your best case, you should include a discussion of the temperature, pressure,
and concentration profiles obtained from Chemcad.

Other Information

It should be assumed that a year equals 8000 hours. This is about 330 days, which
allows for periodic shutdown and maintenance.

Deliverables

General

The entire ammonia process should be optimized using decision variables of your
choosing. Decision variables should be chosen as those most strongly affecting the
objective function. There are topological optimization and parametric optimization. In
topological optimization, which is usually done first, the best process configuration is chosen.
Parametric optimization involves varying operating variables and should be done after
topological optimization is complete. Some examples of parameters that can be used as
decision variables are reactor temperature, pressure, conversion, and distillation column
reflux ratio.

Economic Analysis

When evaluating alternative cases, the equivalent annual operating cost (EAOC)
objective function should be used. The EAOC is defined as

EAOC = -(product value - feed cost – utility costs – waste treatment cost - capital cost
annuity)

A negative EAOC means there is a profit. It is desirable to minimize the EAOC; i.e., a large
negative EAOC is very desirable.

The capital cost annuity is an ​annual cost (like a car payment) associated with the
one-time,​ fixed cost of plant construction.

The capital cost annuity is defined as follows:

(5)

where ​FCI is the installed cost of all equipment; ​i is the interest rate (take ​i = 0.15) and ​n is
the plant life for accounting purposes (take ​n​ = 10).
Other Information

Unless specifically stated in class, the information in this document is valid for this
project only. Any information in the sophomore projects not specifically stated in this
document is not valid for this project.

Deliverables

Written Reports

Each group must deliver a report written using a word processor. Two identical
copies should be submitted, one for each instructor. The written project reports are due by
11:00 a.m. Wednesday, April 21, 2010. Late projects will receive a minimum of a one letter
grade deduction.

The report should be clear and concise. For the correct formatting information, refer
to the document entitled ​Written Design Reports.​ The report must contain a labeled process
flow diagram (PFD) and a stream table, each in the appropriate format. The preferred
software for preparing PFDs is Corel Draw. A PFD from Chemcad is unacceptable;
however, it should be included in the appendix along with a Chemcad report for the base
case. Figure 1 should be used as a template for your PFD. When presenting results for
different cases, graphs are superior to tables. For the optimal case, the report appendix
should contain details of calculations that are easy to follow. These may be hand written if
done neatly. Alternatively, Excel spreadsheets may be included, but these must be well
documented so that the reader can interpret the results. Calculations that cannot be easily
followed and that are not explained will lose credit.

Since this project involves two “mini-designs,” it is suggested that the report be
organized with the following sections. There should be a general abstract and introduction.
Then, there should be a results section followed by a discussion section for each of the
major components of this design project, namely the design of the reactor and separation
strategy. General conclusion and recommendation sections should follow. At a minimum,
there should be separate appendices for each class, ChE 312 and ChE 325, each containing
detailed calculations that are clearly written, easy to follow, and appropriate for the
respective class.

In order to evaluate each group member’s writing skills, the results and discussion
sections for each mini-design should be written by a different group member. The
authorship of each of these mini-reports should be clearly specified in the report. Although
the individual written portions of the reports must be authored by a single group member, it is
the intent of the instructors that group members should help each other in writing different
sections. To this end, we recommend that you seek input, such as proofreading and
critiques, from other members of your group.

The reports will be evaluated as follows:


·​ ​course-specific technical content – 50%
·​ ​oral presentation – 20%

·​ ​written report – 20%

·​ ​technical quality of general sections (safety, simulation, etc.) – 10%

For a more detailed set of evaluation criteria that we will use, see the following web site
(design project assessment, oral report assessment, written report assessment):
http://www.che.cemr.wvu.edu/ugrad/outcomes/rubrics/index.php

Each report will be assessed separately by both instructors. A historical account of what
each group did is neither required nor wanted. Results and explanations should be those
needed to justify your choices, not a litany of everything that was tried. Each mini-report
should be limited to 4-5 double space pages plus figures and tables.

This report should conform to the Department guidelines. It should be bound in a


folder that is not oversized relative to the number of pages in the report. Figures and tables
should be included as appropriate.

The written report is a very important part of the assignment. Poorly written and/or
organized written reports may require re-writing. Be sure to follow the format outlined in the
guidelines for written reports. Failure to follow the prescribed format may be grounds for a
re-write.

The following information, at a minimum, must appear in the main body of the final
report:

1. a computer-generated PFD (not a Chemcad PFD) for the recommended optimum


case,

2. a stream table containing the usual items,

3. a list of new equipment for the process, costs, plus equipment specifications
(presented with a reasonable number of significant figures),

4. a summary table of all utilities used,

5. a clear summary of alternatives considered and a discussion, supported with


figures, of why the chosen alternative is superior,

6. a clear economic analysis which justifies the recommended case

7. a discussion section pertinent to each class plus a general discussion section for
optimization of the entire process

8. a Chemcad report only for your optimized case (in the Appendix). This must
contain the equipment connectivity, thermodynamics, and overall material
balance cover pages; stream flows; equipment summaries; tower profiles; and
tray (packing) design specifications (if you use Chemcad to design the trays
(packing)). It should not contain stream properties. Missing Chemcad output will
not be requested; credit will be deducted as if the information is missing.

Oral Reports

Each group will give an oral report in which the results of this project will be
presented in a concise manner. The oral report should be between 15-20 minutes, and each
group member must speak. Each group member should speak only once. A 5-10 minute
question-and-answer session will follow, and all members must participate. Refer to the
document entitled ​Oral Reports f​ or instructions. The oral presentations will be Wednesday
April 21, 2010, from 11:00 a.m. to 1:00 pm. Attendance is required of all students during their
classmates’ presentations (this means in the room, not in the hall or the computer room).
Failure to attend any of the above-required sessions will result in a decrease of
one-letter grade (per occurrence) from your project grade in ChE 312 and ChE 325.​

Teams

This project will be completed in teams of 3 or 4. More details of group formation and
peer evaluation will be discussed in class.

Revisions

As with any open-ended problem (​i.e.​ , a problem with no single correct answer), the
problem statement above is deliberately vague. The possibility exists that, as you work on
this problem, questions from the class will require revisions and/or clarifications of the
problem statement. You should be aware that these revisions/clarifications might be
forthcoming.

References

1. Eggeman, T., “Ammonia,” ​Kirk-Othmer Encyclopedia of Chemical Technology​,


on-line version, 10/18/2001. (This encyclopedia is accessible from any University
computer at​ ​http://www.libraries.wvu.edu/databases​. An older print version is
available in the Evansdale Library reference section.)

2. Quartulli, Orlando J., William Turner, and Keith W. Padgett, “Ammonia,” in


Encyclopedia of Chemical Processing and Design,​ (J. J. McKetta, ed.), Marcel
Dekker, New York, vol. 3, 256-278 (1977). (This collection is available in the
reference section of the Evansdale Library, first floor, back and to the right.)

3. Wankat, P., ​Separation Process Engineering​, Second Edition, Prentice Hall, Upper
Saddle River, NJ, 2007.
Appendix 1
Economic Data

Equipment Costs (Purchased)

Note: The numbers following the attribute are the minimum and maximum values for that
attribute. For a piece of equipment with a lower attribute value than the minimum, the
minimum attribute value should be used to compute the cost. For a piece of equipment with
a larger attribute value, extrapolation is possible, but inaccurate. To err on the side of
caution, the price for multiple, identical, smaller pieces of equipment should be used.

Pumps
W​ = power (kW, 1, 300)
assume 80% efficiency

Heat Exchangers
A​ = heat exchange area (m​2​, 20, 1000)

Compressors
W​ = power (kW, 450, no limit)
assume 70% efficiency

Compressor Drive
W​ = power (kW, 75, 2600)

Turbine
W​ = power (kW, 100, 4000)
assume 65% efficiency

Fired Heater
Q​ = duty (kW, 3000, 100,000)
assume 80% thermal efficiency
assume it can be designed to use any organic compound as a fuel

Vertical Vessel
V​ = volume of vessel (m​3​, 0.3, 520)

Horizontal Vessel
V​ = volume of vessel (m​3​, 0.1, 628)

Catalyst $2.25/kg

Packed Tower Cost as vessel plus cost of packing

Packing
V​ = packing volume (m​3​, 0.03, 628)

Tray Tower Cost as vessel plus cost of trays

Trays
A​ = tray area (m​2​, 0.07, 12.3)

Reactors For this project, the reactor is considered to be a vessel.


Storage Tanks
V​ = volume of tank (m​3​, 90, 30000)

It may be assumed that pipes and valves are included in the equipment cost factors.
Location of key valves should be specified on the PFD.

Additional Cost Information

Piping straight pipe $/m = 5.0 (nominal pipe diameter, in)(1+(sch #)/20)​0.25

sch​ = schedule number for pipe
use the same sch number for fittings and valves

fittings (except valves) $/fitting = 50.0 (nominal pipe diameter, in)(1+(sch #)/20)​0.25

Valves for gate (isolation) valves $100 (nominal pipe diameter, in)​0.8​ (1+(sch #)/20)​0.25
for control valve use $1000 (nominal pipe diameter, in)​0.8​(1+(sch #)/20)​0.25

Utility Costs

Low-Pressure Steam (618 kPa saturated) $13.28/GJ

Medium-Pressure Steam (1135 kPa saturated) $14.19/GJ

High-Pressure Steam (4237 kPa saturated) $17.70/GJ

Natural Gas (446 kPa, 25C) $11.00/GJ

Fuel Gas Credit $9.00/GJ

Cost of syngas $0.10/kg

Cost of monoethanolamine $2.42/kg

Cost of diethanolamine $2.75/kg

Electricity $0.06/kWh

Boiler Feed Water (at 549 kPa, 90C) $2.45/1000 kg


Cooling Water $0.354/GJ
available at 516 kPa and 30C
return pressure 308 kPa
return temperature is no more than 15C above the inlet temperature

Refrigerated Water $4.43/GJ


available at 516 kPa and 10C
return pressure 308 kPa
return temperature is no higher than 20C

Deionized Water $1.00/1000 kg


available at 5 bar and 30°C

Waste Treatment of Off-Gas incinerated - take fuel


credit

Low Temperature Refrigeration $7.89/GJ


Coolant stream at -20°C

Very Low Temperature Refrigeration $13.11/GJ


Coolant stream at -50°C

Wastewater Treatment $56/1000 m​3

Equipment Cost Factors

Total Installed Cost = Purchased Cost (4 + material factor (MF) + pressure factor (PF))

Pressure < 10 atm, PF = 0.0 does not apply to turbines,


compressors, vessels,
(absolute) 10 - 20 atm, PF = 0.6 packing, trays, or catalyst, since their
cost
20 - 40 atm, PF = 3.0 equations include pressure effects
40 - 50 atm, PR = 5.0
50 - 100 atm, PF = 10

Carbon Steel MF = 0.0


Stainless Steel MF = 4.0

Appendix 2
Information on Reaction Kinetics
The main reaction in the catalytic synthesis of ammonia is

(A2-1)

Experimental analysis of the performance of this catalyst has been reported to give the
following expression for the net rate of reaction of nitrogen:

(A2-2)

where ​kf​ ​ and ​k​r​ are the reaction rate constants for the forward and reverse reactions, the rate
units are kmol/(m​3​ catalyst hr), the partial pressure is in atm, and the gas constant is in
kcal/mol. In Chemcad, chose the activation energy in kcal, the volume in m​3​, the molar flow
in kmol, the mass flow in kg, and the time unit of hr. The rate constants were reported as
follows:

(A2-3)

and

(A2-4)

where the activation energy is given in kcal/kmol and temperature is in Kelvins. The catalyst
is promoted iron oxide, with a specific gravity of 2.6 and a packing void fraction of 0.44.
Remember that the required units in Chemcad for the reaction rate are kmol/m​3​reactor hr.

You may wish to consider several reactor configurations. Some suggested


configurations are shell-and-tube packed bed with heat removal, adiabatic reactor, and
staged adiabatic packed beds with intercooling. There are other possibilities.

You might also like