sign Calculations For Alqibla Project ZONE ZONE

M1
PUMPSTATION INPUT DATA
1-
a- sewage data
GL= 3 M HOUSES 1400 NO
INLET PIPE= 0.8 M #CAP/HOUS 10 CAPITA
INV PIPE= 0 M Qav. /Cap 0.46 M3/DAY
NO. PIPE 1 NO Decrease F 0.9
n= 0.011 DESIGN PER 25 YEARS
pipe length 18 m ∆POP% 0.03%
min. slope = 0.001 PF 3
storm data
SCREEN CHAMBER Atotal= 20 HA
LENGTH= 2 m i= 17 mm/hr
WIDTH= 2 m streat area = m2
BASE OFFSET UNDER INLET PIPE = 0.25 m green area= m2
DISTANCE BETWEEN WETWELL= 3 m buildings area= m2
BASE THIKNES= 0.3 m C= 0.5
WALL THIKNESS= 0.3 m
ROOF THIKNESS= 0.25 m
HEAL WIDTH= 0.8 m
WT= 2 m

NOTES:
sign Calculations For Alqibla Project ZONE M1
PUMPSTATION HYDRAULIC CALCULATION
DISCHARGE CALCULATIONS:
POPULATION:
p= 14,105.38 capita @ 2043
Qavg= 5,839.63 m3/day
Qpeak= 17,518.88 m3/day
Qinft.= 1,751.89 m3/day
Qtotal peak= 19,270.77 m3/day

INLET PIPE CALCULATION:

Assume slope= 0.002 m/m
assumeDia= 0.8 m
Cross Section Area= 0.5024 m
Hydaulic Radius = 0.1256 m
Vfull= 1.01 m/sec
Qfull= 0.51 m3/sec
Qparial=Qtotal peak= 0.22 m3/sec
Qpartial/Qfull= 0.438
d/D= 0.464
Vactu./Vfull= 0.98
Vactu.= 0.99 m/sec
Pipe INV at up= 0 m
Pipe INV at down= -0.036 m
DEPTH OF WATER IN PIPE= 0.3712 m

NOTES: * ELEVATION OF PIPE INV. IN MANHOLE

** ELEVATION OF PIPE INV. IN WETWELL
sign Calculations For Alqibla Project ZONE M1
PUMPSTATION HYDRAULIC CALCULATION
DESIGN OF COARSE SCREEN
Peak Flow 0.2230413034 M3/sec
Coarse Screen Opening 50 mm
Depth of water in screen 0.6212 Mtr.
velocity through screen 0.99 M/sec
Area of screen 0.2247573214 M2
Angle of inclination with the horizontal 45 degree
Sin (Angle of Inclination) 0.7073882692
Free Board 0.6 m
Length of screen 1.7263503697
Width of opening 0.3618115283 mtr
No of opening 7.2362305653 nos
Number of bars 6.2362305653 nos
Let width of each bar be 10 mmx75 mm
Total width of channel 424.17383392 mm
Let width of each side be 50 mm
Total width of channel: Provide 524.17383392 mm
Openings 22.35
No of bars 21.35
Size of Coarse Screen-Width 1.331 m
Size of Coarse Screen-Length 2 m
Velocity in Channal u/s of Screen 0.5434858224
Velocity through Screen 0.6473195791
Head Loss No Clogging 0.0063020285 m
NOTES:
Sewer Pumpstation Design Calculations For Alqibla Project ZONE M1
PUMPSTATION HYDRAULIC CALCULATION
Velocity when 50% clogging 1.294639158 m/sec
Head Loss when 50% clogging 0.070372768 m

GRIT CHAMBER
Here η value taken 75 %
Say 0.75
Here VS value taken 1225 m3/m2/day
Here n value taken-1/8(for very good performance) 0.13
Hence surface over flow rate(Q/A)=(Vs*n)/(((1-η)^-n)-1) 806.4160655 m3/m2/day
Say 810 m3/m2/day
This Q/A value has to be reduced to 0.1 %
Then design overflow rate 729 m3/m2/day
Peak flow(m day)
3/
19270.76861 (m3/day)
Hence area required for peak flow 26.43452485 m2
Each side of square grit chamber 5.141451628 mtr.
Hence provide tank length 5 mtr.
Hence provide tank Width 5 mtr.
Detention time taken is 1 minute
Depth of tank will be 0.50625 mtr.
However in order to provide adequate depth for the grit scrapi 0.9 mtr.
This gives detention time is 0.945732906 minute

NOTES:
Sewer Pumpstation Design Calculations For Alqibla Project M1
PUMPSTATION HYDRAULIC CALCULATION

WEIGHT OF TANK

ROOF ELEV= 3.5 m

length of pipe= -0.0248 m
Sump Elv.= -0.2748 m
WALL HIGH= 3.5248 m
Volume of walls= 8.45952 m
volume of base= 2.52 m
volume of roof= 0.6 m
weight of tank= 28.9488 T
SUBMERCY VOLUME= 13.12896 m3
up ward force = 128.663808 kn
= 12.8663808 T
EXTENSION VOLUME= 2.496 m3
weigh of extention= 6.24 T
DOWN WARD FORCE= 22.7088 T NO FLOATING
Sewer Pumpstation Design Calculations For Alqibla Project M1
PUMPSTATION HYDRAULIC CALCULATION
WETWELL INPUT DATA
Length of tank= 3 m
Width of tank= 3 m Fitting type Quantity K factor Total K factor
GL= 3 m 90º Elbow 4 0.5 2
dist.sump from INP= 2.25 m Tee 1 1.7 1.7
WALL THIKNESS= 0.3 m Reducer 0 0.7 0
BASE THIKNES= 0.3 m Gate Valve 1 0.2 0.2
ROOF THIKNESS= 0.25 m Check valve 1 2 2
pump high 1.6 m
pump width= 0.76 m TOTAL K= 5.9
MIN WATER high= 1.3 m
PUMPING VELOCITY= 3 m3/SEC
force main pipe materials C = 140
force main pipe LENGTH= 700 m
OUTLET STRUCTURE SUMP LEVEL=1.75 M
# CHECK VALVE= 1 NO
#GATE VALVE= 1 NO
# BEND= 4 NO
#TEE = 1 NO
# PUMPS= 2 NO
HEAL WIDTH= 0.8 M
Sewer Pumpstation Design Calculations For Alqibla Project
PUMPSTATION HYDRAULIC CALCULATION

FIND DEPTH OF WELL

hf=(10.67�^1.85)/(�^1.85�^4.87)xL
Top roof Level= 3.55 m
Sump Level= -2.268 m
Depth = 5.818 m

FIND WEIGHT OF TANK

volume of base= 3.888 m3

volume off walls= 5.2362 m3
tanke volume= 9.1242 m3
weight of tank= 22.8105 ton
pressure under tank= 0.844 ton/m2

FIND FORCE MAIN DIA.

D= 0.47
SAY D= 0.35 m

FIND TDH
HS= 4.02 M
HM= 2.71 M
HF= 8.28 M
TDH= 15.00 M
Sewer Pumpstation Design Calculations For Alqibla Project
PUMPSTATION HYDRAULIC CALCULATION

SELECT PUMPS
#PUMPS= 2
Q MAX= 19270.769 m3/day
Q MAX= 802.949 m3/HR
Q MAX= 13.382 m3/MIN
Q MAX= 0.223 M3/SEC
TDH= 15.001 M

TOTAL Q= 0.2230413034 M3/SEC

Q STEP= 0.03 M3/SEC/STEP
QM3/SEC CALC TDH CAPRARI SULZER GRUNDFOS
0.03 6.927 17 15 20
0.06 7.454 16 13 19
0.09 8.268 9 12 17
0.12 9.353 8 9 12
0.15 10.697 5 8 8
0.18 12.291 4 7.5 4
0.21 14.128 3 7 3
0.24 16.202 1 6 1
Sewer Pumpstation Design Calculations For Alqibla Project
PUMPSTATION HYDRAULIC CALCULATION

TRY CAPRARI TRY SULZER

Sewer Pumpstation Design Calculations For Alqibla Project
PUMPSTATION HYDRAULIC CALCULATION

CHECK PUMP

HEAD= 8.5 M
Q= 0.22 M3/SEC
Q= 13.2 M3/MIN
Q= 792 M3/HR
Q= 19008 M3/DAY
PUMP HIGH= 1.6 M
OPERATION CYCLE= 10
LWD= 1 M
DETENSTION TIME= 6 MIN
SYSTEM CURVE
ACTIVE VOLUME= 19.8 M3 WLMIN
WELL CROSS AREA= 21.0 9 M3
0
ACTIVE DEPTH= 2.2000 M
-0.2
LWL= 18.5 -0.968 M
-0.4
MAX WL= 1.232 M
-0.6 P WL
WATER IN PIPE LEVEL 16.0 0.34 M
d/D LEVEL= 0.564 M -0.8
PIPE CROWN LEVEL= f(x) = 13.5
- 21628.3202394302x^4
0.764+ 11819.5847362508x^3
M - 2017.5715488214x^2 + 67.536976912x + 14.3839285714-1
TDH M

HOUSE CONNECTION SUMP LEVEL= 2.20 M -1.2

DEEPUST DEPTH OF NET WORK= 3.04 M P WL PINV WLMAX WLMIN
11.0
0.3 -0.036 1.232 -0.968

8.5

6.0
0 0.05 0.1 0.15 0.2 0.25 0.3

Q M3/SEC

CALC TDH CAPRARI SULZER

Polynomial (SULZER) GRUNDFOS
 8.5

6.0
0 0.05 0.1 0.15 0.2 0.25 0.3

Q M3/SEC

Sewer Pumpstation Design Calculations For Alqibla

CALC TDH Project CAPRARI SULZER
Polynomial (SULZER) GRUNDFOS
PUMPSTATION HYDRAULIC CALCULATION
STRUCTUR CALCULATION FOR HDPE
Loading Information Load Class Pl, lb
Fill height above top of pipe H 49.2 in 1.25 m Field Equipment 10,000
Water height above top of pipe Hw 0 in 0 m H15 12,000
Soil Density gs 120 lbs/ft3 1.92 t/m3 H20 16,000
Vehicle Load on pipe (NEH 636, 52-7) Pl 10000 lbs 5 t
Impact Factor (NEH 636, 52-8) If 1 converter unte
Pressure from the fill above the pipe Ps 3.417541557 psi 2.402769502 t/m2 from to factor
Hydrostatic pressure above the pipe PG 0 psi 0 t/m2 in m 0.0254
Vacuum pressure in the pipe (0 to 5 psi typical) Pv 0 psi 0 t/m2 lbs/ft3 t/m3 0.01601846
Wheel Load Felt by the pipe Pw 1.348252735 psi 0.947915482 t/m2 lbs t 0.0005
Total External Pressure on pipe P 4.765794292 psi 3.350684983 t/m2 psi t/m2 0.7030695783
Pipeline Information (Solid Wall HDPE) in2 m2 0.000645
Input nominal diameter of Pipe 13.8 in 0.35 m lb/ft t/m 0.00147636
Input Standard Dimension Ratio SDR 17 KPA T/M2 0.101972
Input the Pipe Pressure Rating PR 100 psi 70.30695783 t/m2
Pipe Modulus of Elasticity, short term (NEH 636, E 110000 psi 77337.65361 t/m2
Pipe Modulus of Elasticity, long term (NEH 636, Elong 22000 psi 15467.53072 t/m2
Section Modulus, (Pipe Wall Moment of Inertia) Ipw 0.000228667 in4/in
Input Pipe Wall Thickness t 0.14 in 0.003556 m
Input Pipe Outside Diameter OD 14.05952756 in 0.357112 m
Pipe Inside Diameter ID 13.77952756 in 0.35 m
Mean Diameter Dm 13.91952756 in 0.353556 m
Actual Pipe Wall Area Aapw 0.14 in2/in 0.0000903 m2/m
Sewer Pumpstation Design Calculations For Alqibla Project
PUMPSTATION HYDRAULIC CALCULATION
Wall Crushing
Thrust in Pipe wall Tpw 402.03 lb/ft 0.59 t/m
Required Wall Area (long term) Apw 0.04 in2/in 0.00 m2/m Pipe wall will not crush
Actual Pipe Wall Area Aapw 0.14 in2/in
Deflection (%DX/D<=7.5% for pipes other than spillway conduits)
Deflection Lag Factor (NEH 636, 52-11 [1.0 to 1.DL 1.00
Bedding Constant (NEH 636, 52-11 [0.1]) K 0.10
Modulus of soil reaction (see table on Soil ModE' 400.00
Deflection %DX/D 1.13 % Deflection is within limits
Buckling
Buckling Factor of Safety (NEH 636, 52-11) FS 2.50
Water Buoyancy factor (NEH 636, 52-11) Rw 1.00
Coefficient of Elastic Support (NEH 636, 52-11) B' 0.66
Buckling Reduction Factor (NEH 636, 52-12) C 0.90
Wall Buckling Critical Pressure qa 1.41 psi 0.99 t/m2 Buckling will occur!
Pressure Applied by Permanent Loads Pp 3.42 psi 2.40 t/m2
Strain (e all<=5%)
Hoop Strain eh 0.002154 in/in 0.0021538 m/m
Vertical decrease in diameter DY 0.1568 in 0.0039830 M
Flexural Strain ef 0.000028 in/in 0.0000279 M/M
Combined Strain e 0.22 % 0.22 % Pipe Strain is not a problem
Sewer Pumpstation Design Calculations For Alqibla Project
PUMPSTATION HYDRAULIC CALCULATION

BEARING CAPACITY OF SHALLOW FOUNDATIONS

Terzaghi Methods
Input
Units of Measurement
SI SI or E

Foundation Information
Shape SQ SQ, CI, CO, or RE
B= 5.2 m
L= 5.2 m
D= 5.318 m

Soil Information
c= 12 kPa
phi = 18 deg
gamma = 180 kN/m^3
Dw = 1 m

Factor of Safety
F= 3
Sewer Pumpstation Design Calculations For Alqibla Project
PUMPSTATION HYDRAULIC CALCULATION

Unit conversion 1000

Gamma w = 9.8
phi (radians) 0.314

Terzaghi Computations
a theta = 2.04
Nc = 15.52
Nq = 6.04
N gamma = 3.31
gamma' = 170.2
coefficient #1 = 1.3
coefficient #3 = 0.4
sigma zD' = 914.92
W sub f 0

Bearing Capacity
q ult = 6943.46 kPa 708.03889 T/M2
qa= 2314.49 kPa 236.01296 T/M2

Allowable Column Load

P= 62.583754015 kN 6.3817906 TON
Sewer Pumpstation Design Calculations For Alqibla Project
PUMPSTATION HYDRAULIC CALCULATION
DOWN WARD FORCE=
volume of base= 8.112 M3
Volume of walls= 23.03928 M3
volume of roof= 3.267 M3
TOTAL VOLUME= 34.41828 M3
WEIGHT OF TANK= 86.0457 TON
WEIGHT OF FITTING = 5 TON
SURCHARGE WEIGH= 10 TON
TOTAL WEIGH= 101.0457 TON

5.818
BC 3.7368971893 TON/M2 NO COMP. PILE NEED
SUBMERCY VOLUME= 60.58002 M3
up ward force = 60.58002 TON NO BOYANCY CASE
Sewer Pumpstation Design Calculations For Alqibla Project
PUMPSTATION HYDRAULIC CALCULATION

Mass ratio m2/m1

Soil classification according to Norwegian practice

Sewer Pumpstation Design Calculations For Alqibla Project

PUMPSTATION HYDRAULIC CALCULATION
Sewer Pumpstation Design Calculations For Alqibla Project
PUMPSTATION HYDRAULIC CALCULATION
PUMP DISCHARGE TEST
WELL LENGTH= 4
WELL WIDTH= 3
WELL AREA= 12
DRAWDOWN TEST TI 10 MIN
DISTANCE TRAVEL= 0.27 M
SO V FOR ONE PUMP= 3.24 M3
Q= 19.44 M3/HR
THE BOLD NET WORK Q TEST
WELL LENGTH= 4
WELL WIDTH= 3
WELL AREA= 12
RISING TIME 10 MIN
DISTANCE TRAVEL= 0.08 M
V= 0.96 M3
Q= 5.76 M3/HR= 138.24
Q PEAK= Q* P.F= 414.72 M3/DAY
ADD INFILTERATION =10%QMAX=41.5 M3/DAY

TOTAL ALSAHAFIEEN AREA Q= 456.12 M3/DAY

= 19.005 M3/HR
AND MASFEN TOTAL SEWAGE MAX=28352 M3/DAY

TOTAL= 28808.12 M3/DAY= 1200.338 M3/HR

SO MUST ADD NEW PUMPS

USE 3 PUMP EACH PUM Q=600 WITH HEAD 7 M

FROM DATA SHEET OF PUMP POWER =75 KW
NO NEED NEW GENERATOR OR TRANSFORMER BECAUSE AVILBE ONE IS 165 KVA AS GENERATOR AND 250 KVA
ENERATOR AND 250 KVA FOR TRANSFORMER
Q/Qfull h/D V/Vfull R/D B/D
0.001 0.023 0.17 0.0152 0.2998
0.002 0.032 0.21 0.021 0.352
0.005 0.049 0.28 0.0319 0.4317
0.01 0.068 0.34 0.0439 0.5035
0.015 0.083 0.38 0.0532 0.5518
0.02 0.095 0.41 0.0605 0.5864
0.03 0.116 0.46 0.0731 0.6404
0.04 0.134 0.5 0.0837 0.6813
0.05 0.149 0.54 0.0923 0.7122
0.06 0.163 0.57 0.1002 0.7387
0.07 0.176 0.59 0.1075 0.7616
0.08 0.188 0.61 0.1141 0.7814
0.09 0.2 0.63 0.1206 0.8
0.1 0.211 0.65 0.1265 0.816
0.11 0.221 0.67 0.1317 0.8289
0.12 0.231 0.69 0.1369 0.8429
0.13 0.241 0.7 0.1421 0.8554
0.14 0.25 0.72 0.1466 0.866
0.15 0.259 0.73 0.1511 0.8762 1.200
0.16 0.268 0.74 0.1556 0.8858
0.17 0.276 0.76 0.1595 0.894 f(x) =1.000
- 114.9178347864x^6 + 368.829145221x^5 - 459.4994
R² = 0.995678409
0.18 0.285 0.77 0.1638 0.9028 f(x) = 2.3805047753x^6 + 0.8237237396x^5 - 11.5376130386
0.19 0.29 0.78 0.1676 0.9103 0.800
0.2 0.301 0.79 0.1714 0.9174
0.21 0.309 0.8 0.1751 0.9242 0.600
0.22 0.316 0.81 0.1784 0.9298
Axis Title

0.23 0.324 0.82 0.182 0.936

0.400
0.24 0.331 0.83 0.1851 0.9411
0.25 0.339 0.84 0.1887 0.9465
0.200
0.26 0.346 0.85 0.1918 0.9514
0.27 0.353 0.86 0.1948 0.9558
0.28 0.36 0.86 0.1978 0.96 0.000
0.000 0.200 0.400 0.600
0.29 0.367 0.87 0.2007 0.964
0.3 0.374 0.88 0.2037 0.9677 0.200
0.31 0.381 0.89 0.2066 0.9713 q/Q
0.32 0.387 0.89 0.209 0.9741 h/D Polynomial (h/D)
0.33 0.394 0.9 0.2118 0.9773 Polynomial (V/Vfull) R/D
0.34 0.401 0.91 0.2146 0.9802
0.35 0.407 0.92 0.217 0.9802
0.36 0.414 0.92 0.2197 0.9851
0.37 0.42 0.93 0.222 0.9871
0.38 0.426 0.93 0.2243 0.989
0.39 0.433 0.94 0.2269 0.991
0.4 0.439 0.95 0.2291 0.9925
0.41 0.445 0.95 0.2313 0.9939
0.42 0.451 0.96 0.2334 0.9952
0.43 0.458 0.96 0.2359 0.9965
0.44 0.464 0.97 0.238 0.9974
0.45 0.47 0.97 0.2401 0.9982
0.46 0.476 0.98 0.242 0.9988
0.47 0.462 0.99 0.2441 0.9994
0.48 0.488 0.99 0.2461 0.9997
0.49 0.494 1 0.2481 0.9999
0.5 0.5 1 0.25 1
0.51 0.506 1 0.2519 0.9999
0.52 0.512 1.01 0.2538 0.9997
0.53 0.519 1.01 0.2559 0.9993
0.54 0.525 1.02 0.2577 0.9987
0.55 0.531 1.02 0.2595 0.9981
0.56 0.537 1.02 0.2612 0.9973
0.57 0.543 1.03 0.2629 0.9963
0.58 0.55 1.03 0.2649 0.995 h/D
0.59 0.556 1.03 0.2665 0.9937
1.200
0.6 0.562 1.04 0.2681 0.9923
0.62 0.575 1.04 0.2715 0.9987
1.000
0.64 0.587 1.05 0.2745 0.9847
0.65 0.594 1.05 0.2762 0.9822
f(x) = 11.4821925338x^5 - 29.12201915
0.66 0.6 1.05 0.2776 0.9798 0.800

0.68 0.613 1.06 0.2806 0.9741

h/D
0.600

AxisTitle
0.7 0.626 1.06 0.2834 0.9677 Polynomial (h/D)
0.72 0.64 1.07 0.2862 0.96
0.74 0.653 1.07 0.2887 0.952 0.400
0.75 0.66 1.07 0.29 0.9474
0.76 0.667 1.07 0.2912 0.9426 0.200
0.78 0.682 1.07 0.2936 0.9314
0.8 0.697 1.07 0.2958 0.9191
0.000
0.82 0.713 1.08 0.2979 0.9047
0.84 0.729 1.07 0.2997 0.889
0.85 0.738 1.07 0.3006 0.8794
0.86 0.747 1.07 0.3014 0.8695
0.88 0.766 1.07 0.3028 0.8467
0.9 0.786 1.07 0.3038 0.8203
0.92 0.808 1.06 0.3043 0.7877
0.94 0.834 1.05 0.304 0.7442
0.95 0.849 1.05 0.3033 0.7161
0.96 0.865 1.04 0.3022 0.6834
0.98 0.905 1.03 0.2972 0.5864
1 1 1 0.25 0
x^6 + 368.829145221x^5 - 459.4994708314x^4 + 279.4585033704x^3 - 86.138887797x^2 + 13.2197567783x
+ 0.8237237396x^5 - 11.5376130386x^4 + 14.1316266595x^3 - 7.1378148787x^2 + 2.2672419776x + 0.0425100787

200 0.400 0.600 0.800 1.000 1.200

q/Q
Polynomial (h/D) V/Vfull
nomial (V/Vfull) R/D B/D
 h/D
1.200

1.000
) = 11.4821925338x^5 - 29.1220191541x^4 + 27.7687900551x^3 - 12.2640319837x^2 + 3.1103943646x
0.800

h/D
0.600
AxisTitle

Polynomial (h/D)

0.400

0.200

0.000

Axis Title
D= 0.8
imension Description
A Distance from
a centerline of pump inlet
Length of constricted
bell/volute
bay sectiontoatsump
pump
B Clearance
entrance from back
C wall to centerline
Clearance between of
pump
pump inlet
inlet bell/volute
bell and
D Outside diameter of
sump
pump floor
inlet bell/volute
Hmin Minimum water depth in
h sump
Minimum height of
S constricted
Minimum pump bay section
inlet
W bell
Pump submergence
inlet bay width
w Minimum width of
X constricted
Pump inlet baybay length
section
Y Distance from
Z1 centerline
Distance fromof pump inlet
bell/volute
centerline to pump
of screeninlet
Z2 Distance from
bell/volute
centerline to pump
of diverging
 Angle
walls of floor slopeinlet
bell/volute to sloping
 Angle
floor of wall
 convergence
Angle of convergence
from constricted area to
pump bay walls
 Recommended Value
5D 4
2.5D 2
0.75D 0.6
0.3D - 0.5D 0.32
See 8.3.14 Pump
Bell/Intake
S+C Diameter
Greater of H or 2.5D Qp = individual pump capacity, m3/s
See Equation 9-1 Cu = unit conversion coefficient = 0.935
 2D 1.6 D = outside diameter of pump bell/volute, m
2D S = height from lowest pumping level to pump bell/
 5D 4
 4D 3.2
 5D
 5D
0 – 10 degrees
0 – 10 degrees
10 degrees max.
l pump capacity, m3/s
ersion coefficient = 0.935
ameter of pump bell/volute, m
m lowest pumping level to pump bell/volute, m