ENGINE ELECTRICAL

Click on the applicable bookmark to selected the required model year.

 16-1

ENGINE
ELECTRICAL
CONTENTS

CHARGING SYSTEM . . . . . . . . . . . . . . . . 2 Ignition Coil (With Built-in Power Transistor)

Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
GENERAL INFORMATION . . . . . . . . . . . . . . . . 2 Spark Plug Check and Cleaning . . . . . . . . . . . 39
Ignition Failure Sensor Check . . . . . . . . . . . . . 40
SERVICE SPECIFICATIONS . . . . . . . . . . . . . . 3
Camshaft Position Sensor Check, Crank angle
Sensor Check, Detonation Sensor Check . . . 40
SPECIAL TOOL . . . . . . . . . . . . . . . . . . . . . . . . . 4
IGNITION COIL <6G7> . . . . . . . . . . . . . . . . . 41
ON-VEHICLE SERVICE . . . . . . . . . . . . . . . . . . 5
Alternator Output Line Voltage Drop Test . . . . 5 CRANKSHAFT ANGLE SENSOR
Output Current Test . . . . . . . . . . . . . . . . . . . . . . . 6 <6G7> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Regulated Voltage Test . . . . . . . . . . . . . . . . . . . . 8
CAMSHAFT POSITION SENSOR
Waveform Check Using An Analyzer . . . . . . . 11 <6G7> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

ALTERNATOR . . . . . . . . . . . . . . . . . . . . . . . . . 13 DETONATION SENSOR <6G7> . . . . . . . . . 43

STARTING SYSTEM . . . . . . . . . . . . . . . . 23 GLOW SYSTEM . . . . . . . . . . . . . . . . . . . . 44

GENERAL INFORMATION . . . . . . . . . . . . . . 23 GENERAL INFORMATION . . . . . . . . . . . . . . 44

SERVICE SPECIFICATIONS . . . . . . . . . . . . 24 SERVICE SPECIFICATIONS . . . . . . . . . . . . 45

STARTER MOTOR . . . . . . . . . . . . . . . . . . . . . 24 ON-VEHICLE SERVICE . . . . . . . . . . . . . . . . 45

Self-regulating Glow System Check . . . . . . . . 45
IGNITION SYSTEM . . . . . . . . . . . . . . . . . 37
Glow & EGR Control Unit Check . . . . . . . . . . 48
GENERAL INFORMATION . . . . . . . . . . . . . . 37 Engine ECU Check . . . . . . . . . . . . . . . . . . . . . . . 49
Glow Plug Relay Check . . . . . . . . . . . . . . . . . . 50
SERVICE SPECIFICATIONS . . . . . . . . . . . . 38
Glow Plug Check . . . . . . . . . . . . . . . . . . . . . . . . 51
SPECIAL TOOL . . . . . . . . . . . . . . . . . . . . . . . 38 Engine Coolant Temperature Sensor
Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
ON-VEHICLE SERVICE . . . . . . . . . . . . . . . . 38
GLOW PLUG . . . . . . . . . . . . . . . . . . . . . . . . . . 52
16-2 ENGINE ELECTRICAL - Charging System

CHARGING SYSTEM
GENERAL INFORMATION
The charging system uses the alternator output
to keep the battery charged at a constant level
under various electrical loads.

Voltage OPERATION
Rotation of the excited field coil generates AC voltage in
the stator.
This alternating current is rectified through diodes to DC
voltage having a waveform shown in the illustration at left.
Approx. 14.4 V The average output voltage fluctuates slightly with the
alternator load condition.

Time

When the ignition switch is turned on, current flows of approximately 14.4 V, the field current is cut
in the field coil and initial excitation of the field off. When the battery voltage drops below the
coil occurs. regulated voltage, the voltage regulator regulates
When the stator coil begins to generate power after the output voltage to a constant level by controlling
the engine is started, the field coil is excited by the field current.
the output current of the stator coil. In addition, when the field current is constant, the
The alternator output voltage rises as the field alternator output voltage rises as the engine speed
current increases and it falls as the field current increases.
decreases. When the battery voltage (alternator
S terminal voltage) reaches a regulated voltage

SYSTEM DIAGRAM
<6G7>

Stator coil B

Engine-ECU

Field coil
G
S +
Voltage L
regulator Ignition
FR Battery
Charging switch
warning lamp
-
 ENGINE ELECTRICAL - Charging System 16-3
<4D5, 4M4>

Stator coil
Charging
warning lamp

Ignition
Field coil switch
L
Voltage
regulator
S Battery

ALTERNATOR SPECIFICATIONS
Items 6G7, 4M4 4D5

Type Battery voltage sensing Battery voltage sensing

Rated output V/A 12/125 12/105

Voltage regulator Electronic built-in type Electronic built-in type

SERVICE SPECIFICATIONS
Items Standard value Limit

Alternator output line voltage drop (at 30A) V - Max. 0.3

Regulated voltage ambient - 20_C 14.2 - 15.4 -

temp. at voltage regulator V
20_C 13.9 - 14.9 -

60_C 13.4 - 14.6 -

80_C 13.1 - 14.5 -

Output current - 70% of normal output current

Rotor coil resistance W Approx. 2 - 5 -

Maximum vacuum (at 3,000 r/min) <4D56> kPa 90.6 -

Protrusion length of brush mm 6G7, 4D5 - 2

4M4 - 5
16-4 ENGINE ELECTRICAL - Charging System

SPECIAL TOOL
Tool Number Name Use
MD998467 Alternator test Checking the alternator (S terminal voltage)
harness <4D5, 4M4>

MB991519 Alternator test Checking the alternator (S terminal voltage)

harness <6G7>
 ENGINE ELECTRICAL - Charging System 16-5
ON-VEHICLE SERVICE
ALTERNATOR OUTPUT LINE VOLTAGE DROP TEST

Ammeter

+ -

Alternator
Voltmeter

+ - Battery
B-terminal

This test determines whether the wiring from the output wire. (Connect the (+) lead of the
alternator “B” terminal to the battery (+) terminal ammeter to the “B” terminal, and then connect
(including the fusible line) is in a good condition the ( - ) lead of the ammeter to the disconnected
or not. output wire.)
1. Always be sure to check the following before NOTE
the test. An inductive-type ammeter which enables
D Alternator installation measurements to be taken without
D Alternator drive belt tension disconnecting the alternator output wire should
D Fusible link be recommended. Using this equipment will
D Abnormal noise from the alternator while lessen the possibility of a voltage drop caused
the engine is running by a loose “B” terminal connection.
2. Turn the ignition switch off.
3. Disconnect the negative battery cable. 5. Connect a digital-type voltmeter between the
4. Disconnect the alternator output wire from the alternator “B” terminal and the battery (+)
alternator “B” terminal and connect a DC test terminal. (Connect the (+) lead of the voltmeter
ammeter with a range of 0 - 150 A in series to the “B” terminal and the connect the ( - ) lead
between the “B” terminal and the disconnected of the voltmeter to the battery (+) cable.)
16-6 ENGINE ELECTRICAL - Charging System

6. Reconnect the negative battery cable. 11. If the value displayed on the voltmeter is above
7. Connect a tachometer or the MUT-II. the limit value, there is probably a malfunction
8. Leave the hood open. in the alternator output wire, so check the wiring
9. Start the engine. between the alternator “B” terminal and the
10. With the engine running at 2,500 r/min, turn battery (+) terminal (including fusible link).
the headlamps and other lamps on and off If a terminal is not sufficiently tight or if the
to adjust the alternator load so that the value harness has become discolored due to
displayed on the ammeter is slightly above 30 overheating, repair and then test again.
A. 12. After the test, run the engine at idle.
Adjust the engine speed by gradually 13. Turn off all lamps and the ignition switch.
decreasing it until the value displayed on the 14. Remove the tachometer or the MUT-II.
ammeter is 30 A. Take a reading of the value 15. Disconnect the negative battery cable.
displayed on the voltmeter at this time. 16. Disconnect the ammeter and voltmeter.
Limit: max. 0.3 V 17. Connect the alternator output wire to the
alternator “B” terminal.
NOTE 18. Connect the negative battery cable.
When the alternator output is high and the value
displayed on the ammeter does not decrease
until 30 A, set the value to 40 A. Read the
value displayed on the voltmeter at this time.
When the value range is 40 A, the limit is max.
0.4 V.

OUTPUT CURRENT TEST

<6G7>
Load

Voltmeter
Ammeter
Charging warning lamp

Ignition switch

Alternator relay
- + + -

B
FR
L
S
G
Battery
Engine-ECU<M/T> Alternator
or Engine-A/T ECU
<A/T>
 ENGINE ELECTRICAL - Charging System 16-7
<4D5, 4M4>

Charging warning Load

Alternator
lamp

Ignition
switch L
B
Alternator relay
S

Voltmeter
Ammeter

Battery

+ -

This test determines whether the alternator output Caution

current is normal. Never use clips but tighten bolts and nuts
1. Before the test, always be sure to check the to connect the line. Otherwise loose
following. connections (e.g. using clips) will lead to
D Alternator installation a serious accident because of high current.
D Battery NOTE
NOTE An inductive-type ammeter which enables
The battery should be slightly discharged. measurements to be taken without
The load needed by a fully-charged battery disconnecting the alternator output wire should
is insufficient for an accurate test. be recommended.
D Alternator drive belt tension 5. Connect a voltmeter with a range of 0 - 20 V
D Fusible link between the alternator “B” terminal and the
D Abnormal noise from the alternator while earth. (Connect the (+) lead of the voltmeter to
the engine is running. the “B” terminal, and then connect the ( - ) lead
2. Turn the ignition switch off. of the voltmeter to the earth.)
3. Disconnect the negative battery cable. 6. Connect the negative battery cable.
4. Disconnect the alternator output wire from the 7. Connect a tachometer or the MUT-II.
alternator “B” terminal. Connect a DC test 8. Leave the hood open.
ammeter with a range of 0 - 100 A in series 9. Check that the reading on the voltmeter is equal
between the “B” terminal and the disconnected to the battery voltage.
output wire. (Connect the (+) lead of the
ammeter to the “B” terminal. Connect the ( - ) NOTE
lead of the ammeter to the disconnected output If the voltage is 0 V, the cause is probably
wire.) an open circuit in the wire or fusible link between
the alternator “B” terminal and the battery (+)
terminal.
16-8 ENGINE ELECTRICAL - Charging System

10. Turn the light switch on to turn on headlamps D The specified level of current also may not
and then start the engine. be output if the temperature of the alternator
11. Immediately after setting the headlamps to high body or the ambient temperature is too
beam and turning the heater blower switch to high. In such cases, cool the alternator and
the high revolution position, increase the engine then test again.
speed to 2,500 r/min and read the maximum 12. The reading on the ammeter should be above
current output value displayed on the ammeter. the limit value. If the reading is below the limit
Limit: 70% of normal current output value and the alternator output wire is normal,
remove the alternator from the engine and
NOTE check the alternator.
D For the nominal current output, refer to the 13. Run the engine at idle after the test.
Alternator Specifications. 14. Turn the ignition switch off.
D Because the current from the battery will 15. Remove the tachometer or the MUT-II.
soon drop after the engine is started, the 16. Disconnect the negative battery cable.
above step should be carried out as quickly 17. Disconnect the ammeter and voltmeter.
as possible in order to obtain the maximum 18. Connect the alternator output wire to the
current output value. alternator “B” terminal.
D The current output value will depend on 19. Connect the negative battery cable.
the electrical load and the temperature of
the alternator body.
D If the electrical load is small while testing,
the specified level of current may not be
output even though the alternator is normal.
In such cases, increase the electrical load
by leaving the headlamps turned on for
some time to discharge the battery or by
using the lighting system in another vehicle,
and then test again.

REGULATED VOLTAGE TEST

<6G7>
Load
Charging warning
Ignition lamp
switch MB991519
Alternator
FR
Alternator relay L
S
Engine-ECU<M/T> G
or Engine-A/T ECU B
<A/T> Yellow

Ammeter

Voltmeter
Battery

- +
+ -
 ENGINE ELECTRICAL - Charging System 16-9
<4D5, 4M4>

Load
Ignition Charging warning
switch lamp MD998467 Alternator

L
Alternator relay
S B
Ammeter
Voltmeter

Red

Battery + -
Blue

This test determines whether the voltage regulator 6. Connect a DC test ammeter with a range of
is correctly controlling the alternator output voltage. 0 - 100 A in series between the “B” terminal
1. Always be sure to check the following before and the disconnected output wire. (Connect
the test. the (+) lead of the ammeter to the “B” terminal.
D Alternator installation Connect the ( - ) lead of the ammeter to the
D Check that the battery installed in the disconnected output wire.)
vehicle is fully charged. 7. Reconnect the negative battery cable.
D Alternator drive belt tension 8. Connect a tachometer or the MUT-II.
D Fusible link 9. Turn the ignition switch to the ON position and
D Abnormal noise from the alternator while check that the reading on the voltmeter is equal
the engine is running to the battery voltage.
2. Turn the ignition switch off. NOTE
3. Disconnect the negative battery cable. If the voltage is 0 V, the cause is probably
4. Use the special tool (Alternator test harness: an open circuit in the wire or fusible link between
MD998467 or MB991519) to connect a digital the alternator “S” terminal and the battery (+)
voltmeter between the alternator S terminal and terminal.
earth. (Connect the (+) lead of the voltmeter
to the “S“ terminal, and then connect the ( - ) 10. Turn all lamps and accessories off.
lead of the voltmeter to a secure earth or to 11. Start the engine.
the battery ( - ) terminal.) 12. Increase the engine speed to 2,500 r/min.
5. Disconnect the alternator output wire from the 13. Read the value displayed on the voltmeter when
alternator “B” terminal. the alternator output current alternator
becomes 10 A or less.
16-10 ENGINE ELECTRICAL - Charging System

14. If the voltage reading conforms to the value 17. Remove the tachometer or the MUT-II.
in the voltage regulation, then the voltage 18. Disconnect the negative battery cable.
regulator is operating normally. 19. Disconnect the ammeter and voltmeter.
If the voltage is not within the standard value, 20. Connect the alternator output wire to the
there is a malfunction of the voltage regulator alternator “B” terminal.
or of the alternator. 21. Remove the special tool, and return the
15. After the test, lower the engine speed to the connector to the original condition.
idle speed. 22. Connect the negative battery cable.
16. Turn the ignition switch off.

Voltage Regulation Table

Standard value:
Inspection terminal Voltage regulator ambient temperature _C Voltage V

Terminal “S” - 20 14.2 - 15.4

20 13.9 - 14.9

60 13.4 - 14.6

80 13.1 - 14.5
 ENGINE ELECTRICAL - Charging System 16-11
Special
Analyzer
WAVEFORM CHECK USING AN ANALYZER
patterns
Alternator pickup MEASUREMENT METHOD
Connect the analyzer special patterns pick-up to the alternator
B terminal.

B terminal

STANDARD WAVEFORM
Observation Conditions
FUNCTION SPECIAL PATTERNS

PATTERN HEIGHT VARIABLE

VARIABLE knob Adjust while viewing the wave-

form.

PATTERN SELECTOR RASTER

Engine speed Curb idle speed

0.4

0.2
Voltage at
alternator 0
B terminal
- 0.2

- 0.4

Time

NOTE
The voltage waveform of the alternator B terminal can undulate
as shown at left. This waveform is produced when the regulator
operates according to fluctuations in the alternator load
(current), and is normal for the alternator.
In addition, when the voltage waveform reaches an
excessively high value (approx. 2 V or higher at idle), it often
indicates an open circuit due to a brown fuse between
alternator B terminal and battery, but not a defective alternator.
16-12 ENGINE ELECTRICAL - Charging System

EXAMPLES OF ABNORMAL WAVEFORMS

NOTE
1. The size of the waveform patterns differs largely, depending on the adjustment of the variable knob
on the analyzer.
2. Identification of abnormal waveforms is easier when there is a large output current (regulator is not
operating). (Waveforms can be observed when the headlamps are illuminated.)
3. Check the conditions of the charging warning lamp (illuminated/not illuminated). Also, check the charging
system totally.
Abnormal waveforms Problem Abnormal waveforms Problem
cause cause
Example 1 Open diode Example 4 Short in stator
coil

Example 2 Short in diode Example 5 Open supple-

mentary
diode

Example 3 Broken wire in

stator coil

NOTE
At this time, the charging warning lamp
is illuminated.
 ENGINE ELECTRICAL - Charging System 16-13
ALTERNATOR
REMOVAL AND INSTALLATION
<6G7>
Pre-removal and Post-installation Operation
D Air Cleaner Assembly Removal and Installation
(Refer to GROUP 15.)
D Drive Belt Removal and Installation (Refer to
GROUP 11A.)

44 ± 10 N×m

22 ± 4 N×m 1

Disassembly steps
1. Alternator connector
2. Alternator
16-14 ENGINE ELECTRICAL - Charging System

<4D5>
Pre-removal Operation Post-installation Operation
Under Cover Removal D Drive Belt Tension Adjustment (Refer to GROUP
11B – On-vehicle Service.)
D Under Cover Installation

5
22 ± 4 N×m

44 ± 10 N×m

2
3
1

17 ± 2 N×m

Disassembly steps
1. Drive belt 4. Vacuum hose connection
2. Oil pipe connection 5. Alternator
3. Oil return hose connection
 ENGINE ELECTRICAL - Charging System 16-15
<4M4>
Pre-removal Operation Post-installation Operation
D Air Cleaner Assembly Removal (Refer to GROUP D Drive Belt Installation (Refer to GROUP 11C.)
15.) D Drive Belt Tension Adjustment (Refer to GROUP
D Drive Belt Removal (Refer to GROUP 11C.) 11C – On-vehicle Service.)
D Air Cleaner Assembly Installation (Refer to GROUP
15.)

1
3
2

Disassembly steps
1. Alternator connector
2. Adjusting plate
3. Alternator
16-16 ENGINE ELECTRICAL - Charging System

DISASSEMBLY AND REASSEMBLY

<6G7>

3 4

1
5
6
7

12
10
9

14
8
13
11

Disassembly steps
AA" 1. Front bracket assembly AC" 8. Stator
AB" 2. Pulley 9. Plate
"BA 3. Rotor AC" "AA 10. Regulator assembly
4. Rear bearing 11. Brush
5. Bearing retainer 12. Slinger
6. Front bearing 13. Rectifier assembly
7. Front bracket 14. Rear bracket
 ENGINE ELECTRICAL - Charging System 16-17
DISASSEMBLY AND REASSEMBLY
<4D5>

12
9
11

13

15 14

10

22
16

21 1
20

2
18
17 19 3
4
5
6
7

Disassembly steps
1. Check valve 12. Rear bearing
2. Nipple 13. Bearing retainer
3. Vacuum pump housing 14. Front bearing
4. O-ring 15. Front bracket
"CA 5. Vane AC" 16. Stator
"CA 6. Rotor 17. Plate
7. Vacuum pump plate AC" "AA 18. Regulator assembly
8. O-ring 19. Brush
AA" 9. Front bracket assembly 20. Slinger
AB" 10. Pulley 21. Rectifier assembly
"BA 11. Rotor 22. Rear bracket
16-18 ENGINE ELECTRICAL - Charging System

DISASSEMBLY AND REASSEMBLY

<4M4>

1 4
3

5
7 6

14

13
12

10
9

8
11

Disassembly steps
AA" 1. Front bracket assembly AC" 8. Stator
AB" 2. Pulley 9. Plate
"BA 3. Rotor AC" "AA 10. Regulator assembly
4. Rear bearing 11. Brush
5. Bearing retainer 12. Slinger
6. Front bearing 13. Rectifier assembly
7. Front bracket 14. Rear bracket
ENGINE ELECTRICAL - Charging System 16-19
DISASSEMBLY SERVICE POINTS
AA" FRONT BRACKET REMOVAL
1. Remove the bolts.
2. Insert a flat-tipped screwdriver between front bracket and
stator core and pry downwards.
Caution
Do not insert a screwdriver too deep, as the stator
coil will be damaged.

AB" PULLEY REMOVAL

With the pulley side facing up, hold the rotor in a vice and
remove the pulley.
Caution
Use care not to damage the rotor.

AC" STATOR REMOVAL/REGULATOR ASSEMBLY

Soldered
REMOVAL
1. When removing stator, unsolder three stator leads
soldered to main diodes on rectifier.
2. When removing rectifier from brush holder, unsolder two
soldered points to rectifier.
Caution
(1) When soldering or unsoldering, use care to make
sure that heat of soldering iron is not transmitted
to diodes for a long period. Finish soldering or
unsoldering in as short a time as possible.
(2) Use care that no undue force is exerted to leads
of diodes.

REASSEMBLY SERVICE POINT

"AA REGULATOR ASSEMBLY INSTALLATION
Wire Install the regulator assembly, insert a wire into the rear bracket
hole while pushing in the brush, and hold the brush.
NOTE
Inserting a wire holds the brush, so that the rotor can be
replaced easily.
16-20 ENGINE ELECTRICAL - Charging System

Rear bracket

Brush

Wire

"BA ROTOR INSTALLATION

1. When installing the rotor on the alternator rear bracket,
wrap vinyl tape around the splined shaft to prevent
Wind vinyl damage to the oil seal. <4D5>
tape

2. After rotor has been installed, remove the wire.

Wire

Vane Round end "CA ROTOR/VANES INSTALLATION <4D5>

1. Carefully check the housing, rotor, etc. for chips and
foreign matter. Then, apply engine oil and install.
2. Install the vanes with the round end facing outward.
3. Apply grease to the O-ring and fit in the housing groove
so that it will not come out from the groove when the
bolts are tightened.

4. When tightening the housing, lightly push it in the direction

of arrow so as to minimize the clearance at “A” and tighten
the bolts uniformly.
NOTE
After assembly, be sure to conduct a performance test
A
to check to see that the maximum vacuum is as specified
below.
Push housing in
this direction Standard value of maximum vacuum:
90.6 kPa or greater at 3,000 r/min
ENGINE ELECTRICAL - Charging System 16-21
INSPECTION
ROTOR
1. Check rotor coil for continuity. Check that there is no
continuity between slip rings. If resistance is too small,
it means that there is a short circuit. If there is no continuity
or if there is a short circuit, replace rotor assembly.
Resistance value: Approx. 2 - 5 W

2. Check rotor coil for earthing. Check that there is no

continuity between slip ring and core. If there is continuity,
replace rotor assembly.

STATOR
1. Make continuity test on stator coil. Check that there is
continuity between coil leads. If there is no continuity,
replace stator assembly.

2. Check coil for earthing. Check that there is no continuity

between coil and core. If there is continuity, replace stator
assembly.

RECTIFIERS
1. Check for continuity between positive rectifier and stator
coil lead connection terminal with an ohmmeter. If there
is continuity in both directions, diode is shorted. Replace
rectifier assembly.
16-22 ENGINE ELECTRICAL - Charging System

2. Check for continuity between negative rectifier and stator

coil lead connection terminal. If there is continuity in both
directions, diode is shorted, and rectifier assembly must
be replaced.

3. Check three diodes for continuity by connecting an

ammeter to both ends of each diode. If there is no
continuity in both directions, diode is faulty and heatsink
assembly must be replaced.

BRUSH
1. Replace the brush if its protrusion length is less than
the limit.
Protrusion Limit: min. 2 mm <6G7, 4D5>
length min. 5 mm <4M4>

2. Unsolder pigtail and remove old brush and spring.

Soldered

VACUUM PUMP <4D5>

Check the following and replace if defective.
Rotor 1. Check the rotor ends for streaks or damage.
Housing
2. Check the housing surface in contact with the rotor for
streaks or damage.
3. Check the vanes for damage or breaks.

Vane
O-ring
 ENGINE ELECTRICAL - Starting System 16-23

STARTING SYSTEM 16200010368

GENERAL INFORMATION
If the ignition switch is turned to the “START” and M terminal to conduct. Thus, current flows to
position, current flows in the pull-in and holding engage the starter motor.
provided inside magnetic switch, attracting the When the ignition switch is returned to the ”ON”
plunger. When the plunger is attracted, the lever position after starting the engine, the starter clutch
connected to the plunger is actuated to engage is disengaged from the ring gear.
the starter clutch. An overrunning clutch is provided between the
On the other hand, attracting the plunger will turn pinion and the armature shaft, to prevent damage
on the magnetic switch, allowing the B terminal to the starter.

SYSTEM DIAGRAM
Holding coil Plunger
Pull-in coil Lever

Pinion shaft

Overrunning clutch

Ignition
switch

Armature
Battery

Brush
Yoke

Field coil (Except 6G7)

STARTER MOTOR SPECIFICATIONS

Items 6G7 4D5, 4M4
Type Reduction drive with planetary gear Reduction drive with planetary gear
Rated output kW/V 1.2/12 2.2/12
No. of pinion teeth 8 12
16-24 ENGINE ELECTRICAL - Starting System

SERVICE SPECIFICATIONS
Items Standard value Limit
Pinion gap mm 0.5 - 2.0 -
Commutator outer diameter mm 6G7 29.4 28.8
4D5, 4M4 32 31.4
Commutator runout mm 0.05 0.1
Commutator undercut mm 0.5 0.2

Switch STARTER MOTOR 16200110327

S
INSPECTION
M PINION GAP ADJUSTMENT
B
Battery 1. Disconnect field coil wire from M-terminal of magnetic
switch.
2. Connect a 12V battery between S-terminal and
Field coil wire M-terminal.
3. Set switch to “ON”, and pinion will move out.
Caution
This test must be performed quickly (in less than
10 seconds) to prevent coil from burning.
4. Check pinion to stopper clearance (pinion gap) with a
thickness gauge.
Standard value: 0.5 - 2.0 mm

Stopper
Pinion gap

Pinion

5. If pinion gap is out of specification, adjust by adding or

removing gaskets between magnetic switch and front
bracket.

MAGNETIC SWITCH PULL-IN TEST

1. Disconnect field coil wire from M-terminal of magnetic
S switch.
M 2. Connect a 12V battery between S-terminal and
Battery M-terminal.
Caution
This test must be performed quickly (in less than
Field coil wire 10 seconds) to prevent coil from burning.
3. If pinion moves out, then pull-in coil is good. If it doesn’t,
replace magnetic switch.
 ENGINE ELECTRICAL - Starting System 16-25
MAGNETIC SWITCH HOLD-IN TEST
S 1. Disconnect field coil wire from M-terminal of magnetic
switch.
2. Connect a 12V battery between S-terminal and body.
Battery
Caution
This test must be performed quickly (in less than
10 seconds) to prevent coil from burning.
Field coil wire
3. Manually pull out the pinion as far as the pinion stopper
position.
4. If pinion remains out, everything is in order. If pinion moves
in, hold-in circuit is open. Replace magnetic switch.
FREE RUNNING TEST
Carbon-pile rheostat
S 1. Place starter motor in a vise equipped with soft jaws
Ammeter
M and connect a fully-charged 12-volt battery to starter motor
A as follows:
B
2. Connect a test ammeter (100-ampere scale) and carbon
Starter pile rheostat in series with battery positive post and starter
motor V Battery motor terminal.
Voltmeter 3. Connect a voltmeter (15-volt scale) across starter motor.
4. Rotate carbon pile to full-resistance position.
5. Connect battery cable from battery negative post to starter
motor body.
6. Adjust the rheostat until the battery voltage shown by
the voltmeter is 11 V.
7. Confirm that the maximum amperage is within the
specifications and that the starter motor turns smoothly
and freely.
Current: max. 90 Amps (6G7)
max. 130 Amps (4D5, 4M4)

MAGNETIC SWITCH RETURN TEST

1. Disconnect field coil wire from M-terminal of magnetic
switch.
M 2. Connect a 12V battery between M-terminal and body.
Battery
Caution
This test must be performed quickly (in less than
Starter 10 seconds) to prevent coil from burning.
motor Field coil wire
3. Pull pinion out and release. If pinion quickly returns to
its original position, everything is in order. If it doesn’t,
replace magnetic switch.
Caution
Be careful not to get your fingers caught when pulling
out the pinion.
16-26 ENGINE ELECTRICAL - Starting System

REMOVAL AND INSTALLATION

Pre-removal and Post-installation Operation
Under Cover Removal and Installation

<6G7> <4D5>
30 ± 3 N×m

30 ± 3 N×m
1
11 ± 1 N×m
1
11 ± 1 N×m

<4M4>

11 ± 1 N×m 1

Disassembly steps
1. Starter motor assembly
2. Starter cover
 ENGINE ELECTRICAL - Starting System 16-27
DISASSEMBLY AND REASSEMBLY <6G7> 16200120290

12

13
14
16

11

15
1
21

20
19
18 4
17 3

22

8 5

10

Disassembly steps
1. Screw 12. Packing A
AA" 2. Magnetic switch 13. Packing B
3. Screw 14. Plate
4. Screw 15. Planetary gear
5. Rear bracket 16. Lever
6. Brush holder AC" "AA 17. Snap ring
7. Brush AC" "AA 18. Stop ring
8. Rear bearing 19. Overrunning clutch
AB" 9. Armature 20. Internal gear
10. Yoke assembly 21. Planetary gear holder
AB" 11. Ball 22. Front bracket
16-28 ENGINE ELECTRICAL - Starting System

<4D5>

14
12
13
16

11

15 4
1
22
3
21 8

20
19
18
17

23

5
6

10 7

Disassembly steps
1. Screw 13. Plate
AA" 2. Magnetic switch AB" 14. Ball
3. Screw 15. Planetary gear
4. Screw 16. Lever
5. Rear bracket AC" "AA 17. Snap ring
6. Brush holder AC" "AA 18. Stop ring
7. Yoke assembly 19. Overrunning clutch
8. Brush 20. Internal gear
AB" 9. Armature 21. Washer
10. Bearing 22. Planetary gear holder
11. Packing A 23. Front bracket
12. Packing B
 ENGINE ELECTRICAL - Starting System 16-29
<4M4>

15
18 17 23
16

20
19
21
24

5 22
25
26

8
3 7
1
27
12
4
2

9
14
10
13

11

Disassembly steps
1. Stopper ring 15. Cover
2. Pinion stopper 16. Rubber packing A
AD" "BA 3. Pinion 17. Rubber packing B
4. Spring 18. Plate
5. Screw AB" 19. Ball
6. Magnetic switch 20. Planetary gear
7. Screw 21. Lever
8. Screw 22. Washer
9. Rear bracket 23. Washer
10. Brush holder assembly 24. Gear shaft
AE" 11. Yoke assembly 25. Internal gear
12. Brush 26. Overrunning clutch
AB" 13. Armature 27. Front bracket
14. Rear bearing
16-30 ENGINE ELECTRICAL - Starting System

Magnetic switch “S” terminal DISASSEMBLY SERVICE POINTS

AA" MAGNETIC SWITCH REMOVAL
“B” terminal Disconnect field coil wire from “M” terminal of magnetic switch.

“M” terminal
Field coil wire

AB" ARMATURE/BALL REMOVAL

Caution
When removing the armature, take care not to lose the
ball (which is used as a bearing) in the armature end.

AC" SNAP RING/STOP RING REMOVAL

Socket 1. Press stop ring off snap ring with a suitable socket.

Stop ring
Pinion gear
Overrunning
clutch

Snap ring
2. Remove snap ring with snap ring pliers and then remove
Snap ring pliers stop ring and overrunning clutch.
Pinion gear

Over-
running
clutch
 ENGINE ELECTRICAL - Starting System 16-31
Front Pinion AD" PINION REMOVAL <4M4>
Magnet switch bracket Lever Remove the pinion with power supplied to the starter and
the pinion in its popped-out position.
Caution
1. When power is supplied to the starter, the pinion pops
out and rotates. Keep your hands away from the pinion
at this time.
Stopper 2. The magnet switch may be extremely hot after
ring
inspection. Be careful not to touch it.
3. Do not supply power to the pull-in coil P for more
than 10 seconds. Do not supply power to the holding
coil H for more than 30 seconds. If these time limits
are exceeded, the coil(s) may overheat and burn out.
4. The pinion must be popped out electrically by
supplying power to the starter. Do not pop out the
pinion by pulling the lever since the front bracket
and lever may be damaged when the stopper ring
is removed.
5. When the starter is energized, current of more than
100A flows. Thus, heavy-dury cables (as thick as
booster cables) must be used to connect the starter
for inspection, and all connections must be securely
tightened.
1. Connect the starter as shown in the illustration. Here,
C M S
A: Switch,
Pinion B: Switch,
C: Cable,
M: Starter M terminal,
S: Starter S terminal.
NOTE
The following procedure must be carried out with power
supplied to the starter. Thus, the pinion must be removed
within 30 seconds of turning ON the power.
12V DC
2. Supply power to the starter by turning ON switches A
A
and B. The pinion will pop out and rotate.

B
16-32 ENGINE ELECTRICAL - Starting System

3. Within 5 seconds of the pinion’s rotation, turn OFF switch

12 V DC B to stop the pinion from rotating.
A
Caution
B With switches A and B turned ON, power is supplied
to both the pull-in coil P and holding coil H. No voltage
is applied to starter terminal B, so current flows in
the pull-in coil while the pinion is rotating. To prevent
the pull-in coil from burning out, switch B must
therefore be turned OFF within 5 seconds of the
pinion’s rotation.
Pinion
Pinion ring Stopper 4. Apply a suitable tubular tool to the pinion stopper.
ring
5. Lightly tap the tubular tool with a hammer to remove
the stopper ring from the pinion stopper ring groove.
6. Remove the stopper ring and pinion.
Ring groove 7. Turn OFF switch A to cut the supply of power to the
starter.
Tool
Caution
When the starter power is cut, the pinion may pop
in, causing the stopper ring to go back into the ring
groove. If this occurs, switch ON the starter power
and repeat the procedure.
Tool

Brush A AE" YOKE ASSEMBLY REMOVAL <4M4>

Brush 1. Pull the brush spring at point A and raise the brush.
2. After raising the brush, hold it in place with the brush
spring as shown in the illustration.
Brush spring 3. Remove the yoke assembly.
Brush
Yoke assembly

STARTER MOTOR PARTS CLEANING

1. Do not immerse parts in cleaning solvent. Immersing the
yoke and field coil assembly and/or armature will damage
insulation. Wipe motor assembly with a cloth only.
2. Do not immerse drive unit in cleaning solvent. Overrunning
clutch is pre-lubricated at the factory and solvent will wash
lubrication from clutch.
3. The drive unit may be cleaned with a brush moistened
with cleaning solvent and wiped dry with a cloth.
 ENGINE ELECTRICAL - Starting System 16-33
REASSEMBLY SERVICE POINTS
"AA STOP RING/SNAP RING INSTALLATION
Using a suitable pulling tool, pull overrunning clutch stop ring
over snap ring.
Stop ring
Overrunning
Stop ring clutch

Snap ring

Ring groove "BA PINION INSTALLATION

1. Install the pinion and the pinion stopper in the direction
shown in the illustration.
2. Install the stopper ring in the ring groove of the pinion
Stopper shaft assembly (overrunning clutch).
ring
Pinion shaft
Pinion stopper assembly
Pinion (overrunning
clutch)

3. Pulling the pinion hard, secure the pinion stopper to the

Pinion stopper ring.

Pinion stopper

INSPECTION 16200130286

COMMUTATOR CHECK
1. Place the armature in a pair of “V” blocks and check
the runout with a dial indicator.
Standard value: 0.05 mm
Limit: 0.1 mm

2. Measure the commutator outer diameter.

Standard value: 29.4 mm
Limit: 28.8 mm
16-34 ENGINE ELECTRICAL - Starting System

Undercut 3. Check the undercut depth between segments.

Mica Standard value: 0.5 mm
Segment Limit: 0.2 mm

FIELD COIL OPEN-CIRCUIT TEST <4D5, 4M4>

Check the continuity between field brushes. If there is
continuity, the field coil is in order.

FIELD COIL GROUND TEST <4D5, 4M4>

Field brush Check the continuity between field coil brush and yoke. If
there is no continuity, the field coil is free from earth.

Yoke

BRUSH HOLDER CHECK

Check the continuity between brush holder plate and brush
Insulated holder.
brush holder
If there is no continuity, the brush holder is in order.

OVERRUNNING CLUTCH CHECK

1. While holding clutch housing, rotate the pinion. Drive
pinion should rotate smoothly in one direction, but should
not rotate in opposite direction. If clutch does not function
Free properly, replace overrunning clutch assembly.
2. Inspect pinion for wear or burrs. If pinion is worn or burred,
replace overrunning clutch assembly. If pinion is damaged,
Lock also inspect ring gear for wear or burrs.
 ENGINE ELECTRICAL - Starting System 16-35
FRONT AND REAR BRACKET BUSHING CHECK
Inspect bushing for wear or burrs. If bushing is worn or burred,
replace front bracket assembly or rear bracket assembly.

BRUSH AND SPRING REPLACEMENT

<6G7>
1. Brushes that are worn beyond wear limit line, or oil-soaked,
should be replaced.
2. When replacing ground brush, slide the brush from brush
Wear limit line holder by prying retaining spring back.

<4D5>
1. Brushes that are worn beyond wear limit line, or are
oil-soaked, should be replaced.
2. When replacing field coil brushes, crush worn brush with
pliers, taking care not to damage pigtail.

3. Sand pigtail end with sandpaper to ensure good soldering.

New brush 4. Insert pigtail into hole provided in new brush and solder
Pigtail it.
Soldered (Make Make sure that pigtail and excess solder do not come
sure that there is
no excess solder out onto brush surface.
on blush surface) 5. When replacing ground brush, slide the brush from brush
holder by prying retainer spring back.
Surface marked

Growler ARMATURE TEST

ARMATURE SHORT-CIRCUIT TEST
1. Place armature in a growler.
2. Hold a thin steel blade parallel and just above while rotating
armature slowly in growler. A shorted armature will cause
blade to vibrate and be attracted to the core. Replace
shorted armature.
16-36 ENGINE ELECTRICAL - Starting System

ARMATURE COIL EARTH TEST

Check the insulation between each commutator segment and
armature coil core.
If there is no continuity, the insulation is in order.

ARMATURE COIL OPEN-CIRCUIT INSPECTION

Check the continuity between segments. If there is continuity,
the coil is in order.
 ENGINE ELECTRICAL - Ignition System 16-37

IGNITION SYSTEM
GENERAL INFORMATION
This system is equipped with four ignition coils with The engine-ECU <M/T> or engine-A/T-ECU <A/T>
built-in power transistors for each of the cylinders. determines which ignition coil should be controlled
Interruption of the primary current flowing in the by means of the signals from the camshaft position
primary side of an ignition coil generates a high sensor and the crank angle sensor. It also detects
voltage in the secondary side of the ignition coil. the crankshaft position, in order to provide ignition
The high voltage thus generated is applied to the at the most appropriate timing in response to the
spark plugs to generate sparks. engine operation conditions.
The engine-ECU <M/T> or engine-A/T-ECU <A/T> When the engine is cold or running at high altitudes,
turns the power transistors inside the ignition coils the ignition timing is slightly advanced to provide
alternately on and off. This causes the primary optimum performance. Furthermore, if knocking
currents in the ignition coils to be alternately occurs, the ignition timing is gradually retarded until
interrupted and allowed to flow to fire the cylinders knocking ceases.
in the order 1 - 2 - 3 - 4 - 5 - 6.

SYSTEM DIAGRAM

Ignition coill A
To tachometer

Air flow sensor

Barometric pressure
sensor Ignition Ignition coil B
failure
Intake air temperature sensor
sensor
Engine coolant
temperature sensor
Engine-ECU Ignition coil C
Accelerator pedal <M/T> or
position switch
Engine-A/T-
Camshaft position ECU <A/T>
sensor
Ignition coil D
Crank angle sensor
Ignition switch-ST
Detonation sensor
Vehicle speed sensor
Ignition coil E
Inhibitor switch <A/T>

Ignitoin coil F

Spark plug

Cylinder No. 1 2 3 4 5 6
16-38 ENGINE ELECTRICAL - Ignition System

IGNITION COIL SPECIFICATION

Items Specification

Type Molded 6-coil

SPARK PLUG SPECIFICATION

Items 6G7

NGK IZFR5B

SERVICE SPECIFICATIONS
SPARK PLUG
Items Standard value Limit

Spark plug gap mm 0.5 - 0.6 0.75

Spark plug insulation resistance MW - 1

SPECIAL TOOL
Tool Number Name Use
MD998773 Detonation sensor Detonation sensor removal and installation
wrench

ON-VEHICLE SERVICE
1.5 V
+ - IGNITION COIL (WITH BUILT-IN POWER
TRANSISTOR) CHECK
PRIMARY COIL AND POWER TRANSISTOR
- + CONTINUITY CHECK
NOTE
1. An analogue-type circuit tester should be used.
2. Connect the negative ( - ) prove of the circuit tester to
terminal 1.
Caution
This test must be performed quickly (in less than 10
seconds) to prevent coil from burning and power
transistor from breakage.
ENGINE ELECTRICAL - Ignition System 16-39
Voltage: 1.5V Terminal No.
1 2 3
When current is
flowing

When current is
not flowing

SECONDARY COIL CHECK

NOTE
It is impossible to check the secondary coil through the
continuity check as a diode is integrated in the secondary
coil circuit of this ignition coil. So, check the secondary coil
in the following procedure.
1. Disconnect the ignition coil connector.
2. Remove the ignition coil and install a new spark plug
to the ignition coil.
3. Connect the ignition coil connector.
4. Earth the side electrode of the spark plug and crank
the engine.
5. Check that spark is produced between the electrodes of
the spark plug.
6. If no spark is produced, replace the ignition coil with a
new one and recheck.
7. If spark is produced with the new ignition coil, replace
the old one as it is faulty. If no spark is produced again,
the ignition circuit is suspected as faulty. Check the ignition
circuit.

SPARK PLUG CHECK AND CLEANING

Caution
1. The spark plug gap for iridium plugs should not be
adjusted.
2. Cleaning iridium plugs may result in damage to the
iridium tip. Therefore, if cleaning is necessary
because the plug is sooty, use a plug cleaner, and
do not clean the plug for more than 20 seconds in
order to preserve the electrodes. A wire brush should
never be used.
3. The spark plugs in GDI engines are special iridium
plugs in which the electrodes can become black even
when the plugs are working normally. Carbon which
may become deposited on these plugs burns off more
readily than with conventional plugs, and so should
not cause any problems with spark plug performance.
Judgement of whether a spark plug is operating
normally or not should be made by checking the
insulation resistance.
16-40 ENGINE ELECTRICAL - Ignition System

1. Remove the ignition coils.

2. Remove the spark plugs.
3. Check the spark plug gap. Replace the spark plug if the
gap exceeds the limit.
Limit: 0.75 mm
Standard value: 0.5 - 0.6 mm
4. Measure the spark plug insulation resistance. Replace
the spark plug if the measured value is lower than the
limit value.
Limit: 1 MW
5. Clean the spark plug holes.
6. Install the spark plugs.
7. Install the ignition coils.

IGNITION FAILURE SENSOR CHECK

NOTE
An analog-type ohmmeter should be used. Check that the
resistance between terminals 3 and 4 is at the standrad value.
Standard value: 0.1 W or less.

CAMSHAFT POSITION SENSOR CHECK

Refer to GROUP 13A - Troubleshooting. <6G7>
CRANK ANGLE SENSOR CHECK
Refer to GROUP 13A - Troubleshooting. <6G7>
DETONATION SENSOR CHECK
Check the detonation sensor circuit if self-diagnosis code,
No. 31 is shown.
NOTE
For information concerning the self-diagnosis codes, refer
to GROUP 13A - Troubleshooting. <6G7>
 ENGINE ELECTRICAL - Ignition System 16-41
IGNITION COIL<6G7>
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
D Engine Cover Removal and Installation
D Air Cleaner Assembly Removal and Installation
(Refer to GROUP 15.)

3.0 ± 0.4 N×m

3.0 ± 0.4 N×m

10 ± 2 N×m 1
10 ± 2 N×m

2
6

25 ± 5 N×m 3

25 ± 5 N×m

Removal steps <Left bank>

1. Center cover, left
2. Ignition coil
3. Spark plug
Removal steps <Right bank>
D Throttle body (Refer to GROUP 13A.)
4. Center cover, right
5. Ignition coil
6. Spark plug
16-42 ENGINE ELECTRICAL - Ignition System

CRANK ANGLE SENSOR<6G7>

REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
Timing Belt Cover Removal and Installation (Refer to
GROUP 11.)

11 ± 1 N×m

Crank angle sensor

8.5 ± 0.5 N×m

CAMSHAFT POSITION SENSOR <6G7>

REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
Engine Cover Removal and Installation (Refer to
GROUP 11.)

Camshaft position sensor

11 ± 1 N×m
 ENGINE ELECTRICAL - Ignition System 16-43
DETONATION SENSOR <6G7>
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
Intake Manifold Removal and Installation (Refer to
GROUP 15.)

23 ± 2 N×m

AA" "AA 1. Detonation sensor

REMOVAL SERVICE POINT

MD998773 AA" DETONATION SENSOR REMOVAL

INSTALLATION SERVICE POINT

"AA DETONATION SENSOR INSTALLATION
16-44 ENGINE ELECTRICAL - Glow System

GLOW SYSTEM 16400010029

GENERAL INFORMATION
SELF-REGULATING GLOW SYSTEM
The self-regulating glow system reduces the time also the glow indicator lamp illumination time in
required for starting at low temperatures to provide accordance with the engine coolant temperature.
a degree of starting and operation that is identical The resistances of the heating coils which are built
to petrol-engine vehicles by preheating the glow into the glow plugs increase as the glow plug
plugs at super-quick speed. temperatures become higher. As a result of this,
The glow control unit controls both the time during the flow of current gradually decreases, thus
which current is supplied to the glow plugs after stabilizing the glow plug temperature at the
the ignition switch is turned to the ON position and specified temperature.

Glow control unit

Glow plug relay

Pre-heat indicator lamp

Engine coolant Charge lamp

temperature sensor

Glow plugs ON
ST

Ignition switch

Starter motor
Alternator
Battery
 ENGINE ELECTRICAL - Glow System 16-45
SERVICE SPECIFICATIONS 16400030070

Item Standard value

Resistance between glow plug plate and glow plug body 4D5 0.15 - 0.25
(parallel resistance for 4 glow plugs) (at 20 _C) W
4M4 0.05 - 0.07

Voltage between glow plug plate and Immediately after igni- 4D5 9 - 11 (Drops to 0 V after 4 - 8 seconds
glow plug body V tion switch is turned to have passed)
ON (without starting
the engine) 4M4 9 - 11 (Drops to 0 V after approx. 8
seconds have passed)

While engine is cranking 6 or more

While engine is warming up 12 - 15 (Drops to 0 V when the engine

coolant temperature increases to 60 _C
or more or if 180 seconds have passed
since the engine was started)

Glow plug resistance (at 20 _C) W 4D5 0.6 - 1.0

4M4 Approx. 1.1

ON-VEHICLE SERVICE 16400100061

SELF-REGULATING GLOW SYSTEM CHECK

<4D5>
1. Check that the battery voltage is 11 - 13 V.
2. Check that the engine coolant temperature is 40 _C or
less.
NOTE
If the engine coolant temperature is too high, disconnect
the engine coolant temperature sensor connector.

3. Measure the resistance between the glow plug plate and

(+) the glow plug body (earth).
Standard value: 0.15 - 0.25 W (at 20 _C)
NOTE
The resistance value is the parallel resistance value for
the four glow plugs.
4. Connect a voltmeter between the glow plug plate and
(- ) the glow plug body (earth).
5. Measure the voltage immediately after the ignition switch
is turned to ON (without starting the engine).
Standard value:
9 - 11 V (Drops to 0 V after 4 - 8 seconds have
passed)
In addition, check to be sure that the glow indicator lamp
(red) illuminates immediately after the ignition switch is
turned to ON.
NOTE
The time during which the voltage appears (energizing
time) will depend on the engine coolant temperature.
6. Measure the voltage while the engine is cranking.
16-46 ENGINE ELECTRICAL - Glow System

Standard value: 6 V or more

7. Start the engine and measure the voltage while the engine
is warming up.
However, if the engine coolant temperature rises above
60 _C or when 180 seconds have passed since the engine
was started, the voltage will always return to 0 V. (Refer
to the Glow Plug Energization Timing Chart.)
Standard value: 12 - 15 V
<Reference>
Glow Plug Energization Timing Chart

START
Ignition ON
switch
OFF

Glow ON
indicator lamp
OFF

Glow plug ON
relay OFF

Alternator H
L terminal L

T1: Glow indicator lamp

T2: Glow plug relay drive time after ignition switch is turned ON
T3: Glow plug relay drive time after engine starts (after glow)

NOTE
After glow time T3 becomes longer as the engine coolant temperature drops.
 ENGINE ELECTRICAL - Glow System 16-47
<4M4>
1. Check that the battery voltage is 11 - 13 V.
2. Check that the engine coolant temperature is 40 _C or
less.
NOTE
If the engine coolant temperature is too high, disconnect
the engine coolant temperature sensor connector.

3. Measure the resistance between the glow plug plate and

Glow plug the glow plug body (earth).
Standard value: 0.05 - 0.07 W (at 20 _C)
Glow plug plate NOTE
The resistance value is the parallel resistance value for
the four glow plugs.
4. Connect a voltmeter between the glow plug plate and
the glow plug body (earth).
5. Measure the voltage immediately after the ignition switch
is turned to ON (without starting the engine).
START
Standard value:
Ignition
switch ON 9 - 11 V (Drops to 0 V after approx. 8 seconds
OFF have passed)
Glow
indicator ON In addition, check to be sure that the glow indicator lamp
lamp OFF (red) illuminates immediately after the ignition switch is
Alternator turned to ON.
ON
charging
signal (L) OFF NOTE
The time during which the voltage appears (energizing
Glow ON
plug
time) will depend on the engine coolant temperature.
OFF
6. Measure the voltage while the engine is cranking.
Standard value: 6 V or more
7. Start the engine and measure the voltage while the engine
is warming up.
However, if the engine coolant temperature rises above
60 _C or when 180 seconds have passed since the engine
was started, the voltage will always return to 0 V. (Refer
to the Glow Plug Energization Timing Chart.)
Standard value: 12 - 15 V
16-48 ENGINE ELECTRICAL - Glow System

GLOW & EGR-CONTROL UNIT CHECK

<Measure the voltage at the control unit terminals.>

NOTE
(1) Inspect with the control unit connector connected.
(2) When measuring the voltage, connect the control unit terminal (26) to the earth.

Terminal Voltage Reference Table

Inspection Inspection item Inspection condition Standard value
terminal
5 Engine coolant Ignition switch Engine coolant temperature: - 20 _C 4.3 - 4.5 V
temperature sensor “OFF” ® “ON”
(Engine coolant Engine coolant temperature: 0 _C 3.7 - 3.9 V
temperature detec-
tion) Engine coolant temperature: 20 _C 2.8 - 3.0 V

Engine coolant temperature: 40 _C 1.9 - 2.1 V

Engine coolant temperature: 80 _C 0.5 - 0.7 V

12 Ignition switch (power Ignition switch “LOCK(OFF)” ® “START” 8 V or more

supply)
14 Glow plug relay Ignition switch “LOCK(OFF)” ® “ON” 9 - 12 V
(glow time control) Engine coolant temperature: 40 _C or less 0 - 0.5 V after
(Pre-glow function inspection) approx. 8 sec.
(when engine
coolant tempera-
ture is 20 _C)

17 Glow indicator lamp Ignition switch “LOCK(OFF)” ® “ON” 0 - 1V

Engine coolant temperature: 40 _C or less 11 - 13 V after
approx. 1 sec.
(when engine
coolant tempera-
ture is 20 _C)
23 Alternator charging Ignition switch “LOCK(OFF)” ® “ON” 1 - 4V
signal (“L” terminal)
Engine is idling 11 V or more
26 Earth - -

Remove the control unit connector and check the continuity

between the harness-side connector terminals.
Harness-side connector
Inspection Inspection item Continuity
terminal (resistance value)
14 - 26 Glow plug relay Continuity (approx.
20W)
 ENGINE ELECTRICAL - Glow System 16-49
ENGINE-ECU CHECK

<Measure the voltage at the control unit terminals.>

NOTE
(1) Inspect with the control unit connector connected.
(2) When measuring the voltage, connect the control unit terminal (26) to the earth.

Terminal Voltage Reference Table

Inspection Inspection item Inspection condition Standard value
terminal
83 Engine coolant Ignition switch Engine coolant temperature: - 20 _C 4.3 - 4.5 V
temperature sensor “LOCK (OFF)”
(Engine coolant ® “ON” Engine coolant temperature: 0 _C 3.7 - 3.9 V
temperature detec-
tion) Engine coolant temperature: 20 _C 2.8 - 3.0 V
Engine coolant temperature: 40 _C 1.9 - 2.1 V
Engine coolant temperature: 80 _C 0.5 - 0.7 V
82 Ignition switch (power Ignition switch “LOCK (OFF)” ® “START” 8 V or more
supply)
16 Glow plug relay Ignition switch “LOCK (OFF)” ® “ON” 9 - 12 V
(glow time control) (Pre-glow function inspection) 0 - 0.5 V after
approx. 8 sec.
(when engine
coolant tempera-
ture is 20 _C)
After starting engine 12 V
(After-glow function check) 0 V approx. 180
sec. (when
engine coolant
temperature is
20 _C)
4 Glow indicator lamp Ignition switch “LOCK (OFF)” ® “ON” 0 - 1V
Engine coolant temperature: 40 _C or less 11 - 13 V after
approx. 1 sec.
(when engine
coolant tempera-
ture is 20 _C)
82 Alternator charging Ignition switch “LOCK (OFF)” ® “ON” 0V
signal (“L” terminal)
Engine is idling 11 V or more
Charge lamp Ignition switch “LOCK (OFF)” ® “ON” 12 V
Immediately after the glow indicator lamp turns off and 0 V approx. 6
on. sec. (When
engine coolant
temperature is
20 _C)
26 Earth - -
16-50 ENGINE ELECTRICAL - Glow System

Remove the control unit connector and check the continuity

between the harness-side connector terminals.
Harness-side connector
Inspection Inspection item Continuity
terminal (resistance value)
13 - 16 Glow plug relay Continuity (approx.
3W)

<4D5> GLOW PLUG RELAY CHECK 16400250032

1. Check to be sure that there is continuity (approx. 20 W)

Glow plug relay between glow plug relay terminal (1) and the bracket
(earth).
2. Use jumper cables to connect terminal (1) of the glow
plug relay to the battery (+) terminal and the bracket
to the battery ( - ) terminal
Caution
(1) Always be sure to disconnect the harnesses
connected to glow plug relay terminals (2) and
(3) before using the jumper cables.
<4M4> (2) The terminals of the disconnected harnesses must
not be shorted to earth.
(3) When connecting the jumper cables, be very
careful not to make a mistake in connecting the
terminals, as this will cause damage to the relay.
3. Check the continuity between glow plug relay terminals
(2) and (3) while disconnecting and connecting the jumper
cable at the battery (+) terminal

Glow plug relay Jumper cable at battery (+) Continuity between terminals
terminal (2) - (3)
Connected Continuity (0.01 W or less)
Disconnected No continuity (infinite
Battery resistance)

Glow plug
relay Bracket
(earth)
 ENGINE ELECTRICAL - Glow System 16-51
GLOW PLUG CHECK 16400190082

1. Remove the glow plug plate.

(+)
2. Measure the resistance between the glow plug terminals
and the body.
Standard value:
0.6 - 1.0 W (at 20 _C) <4D5>
Approx. 1.1 W (at 20 _C) <4M4>
(- )

ENGINE COOLANT TEMPERATURE SENSOR

CHECK
Refer to GROUP 13B - On-vehicle service <4D5> or GROUP
13C - On-vehicle service <4M4>
16-52 ENGINE ELECTRICAL - Glow System

GLOW PLUG
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
EGR Pipe Removal and Installation (Refer to GROUP
17.)

<4M4> <4D5>

1.8 ± 0.2 N×m 1.8 ± 0.2 N×m

1.8 ± 0.2 N×m
1
1

1.8 ± 0.2 N×m

2
3
3
18 ± 2 N×m 2

Removal steps
1. Connector connection
2. Glow plug plate
AA" 3. Glow plug

REMOVAL SERVICE POINT

AA" GLOW PLUG REMOVAL
The ceramic part of the glow plug can be easily damaged.
When removing the glow plug, first loosen the plug with a
wrench until the last one thread or more is remained, then
remove it with your finger.
Caution
The glow plug, which has been dropped from a height
of 10 cm or more, can not be reused.
16-1 ENGINE ELECTRICAL - Glow System <4D5-Step III>

GROUP 16
ENGINE ELECTRICAL
GLOW SYSTEM <4D5-STEP III>
GENERAL
OUTLINE OF CHANGE
Glow system control is now carried out by the engine-ECU to correspond to the adoption of an
electronically-controlled fuel injection system.
Refer to GROUP 13E - Troubleshooting for details on measuring the ECU terminal voltage as a result
of this.