Scribd
Upload
169 views

Computer: A Computer Is A Multipurpose Programmable Machine That Reads

The document discusses computers and microcomputers. It defines a computer as a programmable machine that processes data according to instructions. A microcomputer uses a microprocessor as its central processing unit (CPU). The first commercial microprocessor was the 4-bit Intel 4004 introduced in 1971. A microprocessor is a general purpose digital CPU that is essentially a "computer on a chip". It contains an arithmetic logic unit, registers, a program counter, stack pointer, and clock/interrupt circuits. By adding memory, input/output devices, and peripherals, a microcomputer can be used for a variety of general purpose applications.

Uploaded by

Harshit Goyal
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
169 views

Computer: A Computer Is A Multipurpose Programmable Machine That Reads

The document discusses computers and microcomputers. It defines a computer as a programmable machine that processes data according to instructions. A microcomputer uses a microprocessor as its central processing unit (CPU). The first commercial microprocessor was the 4-bit Intel 4004 introduced in 1971. A microprocessor is a general purpose digital CPU that is essentially a "computer on a chip". It contains an arithmetic logic unit, registers, a program counter, stack pointer, and clock/interrupt circuits. By adding memory, input/output devices, and peripherals, a microcomputer can be used for a variety of general purpose applications.

Uploaded by

Harshit Goyal
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

INTRODUCTION

Computer: A computer is a multipurpose programmable machine that reads


binary instructions from its memory , accepts binary data as input ,processes
the data according to those instructions and provides results as output. It is a
programmable device made up of both hardware and software. The various
components of the computer are called hardware. A set of instructions written
for the computer to solve a specific task is called program and collection of
programs is called software .

The computer hardware consists of four main components. The central


processing unit which acts as computer’s brain. Input unit through which
program and data can be entered to computer, output unit on which the
results of the computations can be displayed. Memory in which data and
program are stored.

Fig 1. Block diagram of a microcomputer

A computer that is designed using a microprocessor as its CPU , is known as a


microcomputer.

Microprocessor or ‘Computer on Chip’ first became a commercial reality in


1971 with the introduction of the 4 bit 4004 by Intel. A byproduct of
Microprocessor development was Microcontroller. The same fabrication
technology and programming concept that make the general purpose
microprocessor also yielded the Microcontroller.
Microprocessors

A microprocessor is a general purpose digital computer central processing unit


(CPU). Although known as a ‘Computer on Chip’ the Microprocessor in no
sense a complete digital computer. Block diagram of a Microprocessor CPU
which contains ALU; Program counter (PC), a stack pointer (SP) ,some working
registers , a clock timing circuit and interrupt circuit s is shown in the following
figure

Arithmetic and Logic


Unit

Accumulator

Working Register

Program Counter Stack Pointer

Clock Circuit Interrupt Circuits

Fig.2.Block Diagram of a Microprocessor

The microprocessor can be viewed as a programmable logic device that can


be used to control processes or to turn on /off devices. On the other hand
microprocessor can be viewed as a data processing unit or a computing unit
of a computer. The microprocessor is a programmable integrated device that
has computing and decision making capability similar to that of the CPU od a
computer. A microprocessor is a multipurpose, programmable, clock-driven,
register based electronic device that reads binary instructions from a storage
device called memory; accepts binary data as inputs and process data
according to those instructions, and provide results as output.
To make a computer microcomputer one must add memory usually RAM
and ROM, memory decoders , an oscillator and a number of Input ,Output
devices such as serial and parallel ports. In addition special purpose devices
such as interrupt handler and counters may be added to relieve the CPU from
time consuming counting or timing cores. When the Microcomputer is
equipped with mass storage devices , I/O peripherals such as a key board and a
display CRT it yields a small computer that can be applied to a range of general
purpose applications.

The hardware design of a microprocessor is arranged such that a very


small or very large system can be configured around the CPU as the application
demands as shown in Fig1. The prime use of the Microprocessor is to read data
, perform extensive calculations on that data, and store those calculations in a
mass storage device or display the results for human use. The programs used
by microprocessor are stored in the mass storage device and loaded into RAM
as user directs. A few microprocessor program are stored in ROM . The ROM
based programs are primarily small fixed programs that operate peripherals
and other fixed devices that are connected to the system.

You might also like