Induction Technology Reports

Steelmaking based
on inductive melting

by Mohamed Chaabet, Erwin Dötsch

Global production of steel has experienced rapid growth for a prolonged time. Over the last ten years alone,
annual production rose from 851 Mt/a in 2001 to 1,417 Mt/a in 2010, much of this being attributable to growth in
China. The percentage of electric steel produced with electric arc furnaces as the traditional melting unit around
the world (without China, an exceptional case with 90 % oxygen steel) is around 45 %, and this percentage
is growing. After the development of induction technology with inverter outputs of over 40 MW for crucible
furnaces with capacities of more than 65 t, the induction furnace offers itself as an alternative electric melting unit
for small mini-mills. Apart from saving the costs of electrodes and the low requirements on the electricity grid,
the main benefits offered by induction furnaces are the high yield from the feed materials and low pollution of
the environment and workplaces. The low metal losses becomes an economic factor, particularly when stainless
steels are produced; although promising results have also been obtained in recent times for the inductive
melting of carbon steels.

S
teel is the most important industrial material for [4]. Corresponding to these processes, a differentiation is
producing goods and plants by a long way, as can made between oxygen steel and electric steel.
be seen from the quantities of the main materi- The electric steel process is characterized by its flexibil-
als produced across the world as depicted in Fig. 1 ity and, in the case of smaller steelmaking units (so-called
[1]. Fig. 2 shows the rapid, on-going development of mini-mills with 300 to 1,200 kt/a) its cost effectiveness.
world steel production since 1950 which, according to A further factor is the lower environmental pollution, in
Ameling's estimates made in 2006, would reach some that less dust, CO2, NOx and slag is produced compared
1,500 Mt/a in 2010. The crude steel produced each year to the oxygen process [5]. The relative, absolute growth in
in the various regions during last 10 years is depicted in electric steelmaking across the world, with the exception
Fig. 3. This clearly shows that this annual tonnage - at
1,417 Mt/a - was almost achieved, despite the collapse
in 2008/2009. The main reason for this is the astonishing
growth in China, where the annual tonnage of 152 Mt in
2001 increased more than fourfold to 627 Mt in 2010 [2].
Steel production processes are characterized by a high
recycling rate of steel scrap. This lies between 85 and
90 % in industry and for automobiles, and at 50 % in the
private sector [3]. As the ratio of scrap used as the raw
material for producing steel is 40 to 45 %, it is nowadays
almost on equal terms with iron ore. Fig. 4 shows the
processes used to produce steel in diagrammatic form,
the two main processes used to produce well over 90 %
of all steel can be seen on the far left and far right. These
are namely the lines "blast furnace/oxygen-converter" Fig. 1: Global production of the most important materials
which primarily uses ore as the raw material, and the 1970/2006, in Mt/a [1]
"electric arc furnace" with scrap as the main input basis

1-2012 heat processing   49

 
 Reports Induction Technology

of China and Japan, is therefore not sur-

prising. Fig. 5 and 6 show that this trend
is especially noticeable in the countries
of the Near East, in Turkey and in India.
Growth in China, in contrast, is mainly
attributable to large-scale oxygen steel
works, so that the comparatively mod-
erate rise in the production of electric
steel from 24 Mt in 2001 to 64 Mt in 2010
reflects the relatively low percentage of
electric steelmaking at below 10 %. In
the rest of the world production of elec-
tric steel rose from 323 Mt/a in 2001 to
350 Mt/a in 2010, thereby increasing its
share of total steel production from 44
Fig. 2: The trend in global steel production, after Ameling [1] to 46 % [2].
As illustrated in Fig. 4, the melting
stock used to produce electrical steel
partly consists of so-called direct
reduced iron (DRI). This is produced in
the direct reduction process, in which
prepared iron ore pellets are reduced
from oxygen in their solid state by a heat
and reduction gas, consisting of carbon
monoxide and hydrogen, or even by
coal [6]. The direct reduced iron which
results is a porous product, so called
sponge iron. It arises after reduction at
a temperature of 600 to 900 °C and is
often pressed while hot into HBI (Hot
Briquetted Iron). The direct reduction
process has economic significance in
Fig. 3: Production of crude steel from 2005 to 2010 [2]
regions where natural gas is available
as a resource for the reduction gas or
gasifiable coal can substitute coke. The
DRI tonnages depicted in Fig. 7 show
that these favorable conditions for direct
reduction are particularly found in the
Near East and in India. Consequently, of
the 41 Mt/a of electric steel produced in
India, 62 % (30 Mt/a) is made from direct
reduced iron. The worldwide share of
DRI is 15 % and growing.
As far as the continuous growth of
global steel production is concerned,
it can be expected that the recycling
rate of steel scrap will at least remain at
today's high level and that the impor-
tance of DRI as melting stock will rise.
There will therefore be further growth
in the production of electric steel. The
most interesting component here from
Fig. 4: Processing routes in steel production [4] a technical and economic viewpoint is
the "electric furnace" as the melting unit.

50     heat processing 1-2012

 Induction Technology Reports

Apart from the established electric arc

furnaces, it seems likely that induction
furnaces will also be deployed in this
context. In what follows, the character-
istic properties of the induction furnace
is first described before some example
systems for steelmaking are discussed.

Characteristic
features of induction
furnaces
There are two main types of induc-
tion furnaces used in industry, namely
the induction channel furnace and the
induction crucible furnace. Channel fur-
naces nowadays only have subordinate Fig. 5: Electric steel production from 2001 to 2010 [2]
significance as equipment for melting
ferrous materials, so that what follows
refers to crucible furnaces. Fig. 8 con-
tains a diagram of such an induction
melting system. Its main components
are the power supply unit (with trans-
former, inverter and capacitor bank), the
crucible furnace itself, the charging sys-
tem, the cooling systems for the power
supply and furnace coil, the fume extrac-
tion equipment and the process control
system [7].

Power transmission without over

temperature
The crucible furnace itself is a melting
unit with a fairly simple construction. As
Fig. 6: Electric steel production as a percentage of total crude steel
shown in Figure 8, this basically consists
production, 2001 and 2010 [2]
of the refractory crucible and the sur-
rounding coil borne by a steel frame.
Alternating current flows through the
coil, creating an electromagnetic field.
This field induces eddy currents in the
metallic melting stock which, in accor-
dance with Joule’s law, cause the feed
materials to heat up and finally to melt.
The heat is thus generated directly
in the melting stock itself, without over
temperature, so that the emissions gen-
erated by furnaces heated by fuel or
electric arc during power transmission
do not occur in the induction furnace.
Depending on the quality of the feed
materials, the volume of dust produced
is 0.5 to 1 kg/t of melt, the slag ratio is
10 to 15 kg/t. Further benefits of energy
Fig. 7: DRI production in million t/a in 2001, 2005 and 2010 [2]
transmission without over temperature
are that premature refractory wear does

1-2012 heat processing   51

 
 Reports Induction Technology

radial direction to the crucible axis and thus press the

melt inwards away from the crucible wall. Gravity works
against these forces, so that a dome is formed on the
bath surface. In addition, a bath flow is created in the
form of two eddy toroids with opposite directions of
turn. This is attributable to the fact that the radial pressure
on the melt reaches a maximum around halfway up the
coil due to the leakage of the field at the coil ends (Fig. 9
right).
The inductive bath agitation firstly leads to an ideal
homogenization of the melt with regard to the chemical
composition and temperature. It is furthermore beneficial
for stirring in specific light materials, such as chips, stamp-
ing remnants, shredded scrap and sponge iron. Given a
suitable method of charging, these materials are stirred
spontaneously into the melt, so that optimum heat trans-
mission conditions are created for melting the individual
pieces of feed stock.

Inverter power supply

Power is supplied to the furnace coil via a transformer,
a frequency inverter and a capacitor bank to compen-
sate for the furnace reactive power, as depicted in Fig.
8. At a cos phi of some 0.95 in the range of 60 to 100 %
of the nominal power, for the electrical supply grid the
Fig. 8: Structure of an induction melting installation, ABP type
induction furnace thus represents a "pure" Ohm load.
Moreover, this is constant in time, thus without short-
term fluctuations. In addition, as the furnace is switched
not occur as a result of excessive wall temperatures, gas on via a time ramp, all types of flickers and grid load-
take-up from the atmosphere is very low and, above ing through rush currents are prevented. Thanks to the
all, that the burnout of the feed materials and alloying 24-pulse design of the converter, the 5th, 7th, 11th and 13th
agents is minimal. harmonic caused by the inverter are largely reduced, so
that just the 23rd harmonic becomes effective for the grid
Inductive bath agitation and thus adverse effects do not normally occur.
The diagram in Fig. 9 (left) shows the magnetic flux The current fed in by the inverter oscillates with a
generated by the coil current which partly runs through resonance frequency (between 60 % and 110 % of the
the melt [8]. The interplay between the eddy currents nominal frequency) that adapts itself independently in
induced in the melt and the magnetic induction cre- the high power circuit between the furnace coil and
ates electromagnetic forces, which basically run in a capacitor bank, and thus enables a constant load regula-

Fig. 9: Field image of a medium-

frequency crucible furnace (left),
Power distribution and flow
pattern (right) [8]

52     heat processing 1-2012

 Induction Technology Reports

tion in a simple manner. The available power can thus be ■ High mechanical and chemical resistance in order to
fully used practically for every state of the melting stock withstand the loading caused by the bath agitation.
in the crucible, i.e. over the complete melting period, by These requirements are fulfilled for the inductive melting
variable current, voltage and frequency. These demon- of cast iron by quartzite dry masses. Quartzite, however,
strate the main advantages of an inverter power sup- is unsuitable for producing steel melts due to its inad-
ply compared to a conventional line frequency furnace, equate thermal and chemical resistance. Spinel-forming
which only works economically in heel operation at a dry masses on MgO and Al2O3 basis are the lining materi-
rigid line frequency. The variable and higher frequency als preferred for this purpose. They are characterized by a
of the coil current in the oscillation circuit with the vari- high temperature application limit of over 1,750 °C, whilst
able current and voltage enables the MF furnace to be at the same time having a favorable thermal stability and
operated in charging mode, i.e. without heel with solid a low infiltration tendency.
feed materials, without forfeiting anything in the melt- The latter named feature is based primarily on the for-
ing performance, and it can be equipped with a power mation of spinel whilst the applied mass is being sintered:
input many times as great, yet at the same capacity [9]. The formation of the spinel (MgO•Al2O3), consisting of
This, then, is the essential progress made compared to magnesite and corundum, is associated with an increase
the situation in the 1970s, when efforts to deploy the line in volume of 7.9 %. This not only compensates the shrink-
frequency induction furnace for steelmaking met with age which occurs from around 1,200 °C during sintering
little or no success [10]. without such reactions, but also leads to an additional
densification in the sintered layer [12].
Operating behavior and environmental
compatibility Deployment of induction
The principle of direct energy transmission, as described furnaces in steel mills
above, produces a high yield from the feed materials with Induction technology has now been developed to the
lower levels of dust emission. Noise levels are kept within extent that it is possible to generate connected loads of
admissible limits below 85 to 83 dB(A), firstly because the over 40 MW per inverter and specific power between 600
noisy power supply components (choke, inverter, capaci- and 800 kW/t of furnace capacity. These developments
tor bank) are installed in enclosed rooms and, secondly, fulfill the prerequisites for deploying induction crucible
the call for lower noise emissions is taken
into account in the furnace construction
with the furnace casing and platform being Table 1: Characteristic features of electric arc and induction furnaces (source: ABP)
acoustically insulated [11]. The low levels of
heat released into the surroundings also Feature Electric Arc Furnace Induction Furnace
make the induction furnace a melting unit
which is friendly to the workplace. Operation costs:
• Electrical energy 500 kWh/t 540 kWh/t
Refractory lining • Refractory 4 kg/t 3.5 kg/t
As a rule, crucible furnaces are lined with • Electrodes 2.5 kg/t none
powdery dry masses. These are sintered • Oxygen 15 Nm³/t none
in the furnace into a monolithic, although • Slag builder 25 kg/t none
elastic crucible. The induction process Melting:
thereby places particular requirements on • Melt losses • 7 to 10 % • 1 to 2 %
the refractory lining: • Alloying • Not exact • Simple and exact
■ Lowest possible wall thickness in order
Metallurgical work:
to keep the expenditure for the capacitor
• Decarburizing
bank to compensate the reactive power Possible by oxygen Restricted by refractory
• Desulphurizing
low and electrical efficiency high. blowing and slag reaction wear
• Dephosphurizing
■ Metal may not be allowed to penetrate
the refractory wall. This is because mate- Environment conditions:
rials conducting electricity in the furnace • Dust 5 to 10 kg/t approx. 1 kg/t
refractory are inductively heated up, so • Noise 90 to 120 dB(A) 83 to 85 dB(A)
that the penetrating metal melt does not • Slag 60 to 70 kg/t 10 to 15 kg/t
stand still, but rather penetrates through
• High load • Low load
to the coil, thereby causing a short circuit Electrical supply net
• Flicker disturbances • No flicker disturbances
or even a molten metal break-through.

1-2012 heat processing     53

 Reports Induction Technology

furnaces in steel works in two fields: Firstly, the induction service life is not impaired. When considering the chemi-
furnace as the melting unit for mini-mills with an annual cal composition of the metallic feed materials, it should
production of 100,000 to 900,000 t/a is now an alternative be noted that the induction furnace is suitable for adding
to the electric arc furnace. Secondly, it is suitable for melt- agents, i.e. alloys, at any time thanks to the characteristic
ing the ferroalloys for adding to the ladle in liquid form bath agitation. However, it is not very good for removing
when making stainless steel. components, such as carbon through oxygen treatment.
This is to be discussed in more detail later.
The induction furnace as an alternative melting The inductive bath agitation also represents a benefit
unit to the electric arc furnace for melting direct reduced iron. Melting performance is
Table 1 compares the main features of electric arc and nevertheless limited by the boiling process to remove the
induction furnaces for melting steel in mini-mills. Accord- residual oxygen (which is associated with the formation
ing to this, an induction furnace has the following eco- of flames and splashes of molten metal) and by severe
nomic/technical benefits, these resulting from the inter- slag formation which requires special action.
plays described in the foregoing section.
■ Low requirements on the electricity grid; also suitable Design of an induction melting system for
for power supplied by generators driven by diesel or producing construction steel billets
gas In electric steelmaking, it has long since been regarded
■ Little expenditure for environmental compatibility and as making economic sense to perform metallurgical work
clean workplaces not in the melting furnace itself, but rather in down-
■ High yield from the metallic feed materials, above all stream equipment, such as a ladle furnace, oxygen con-
the alloying agents verter or vacuum plant [13]. The process of producing the
■ No electrode costs melt is thus characterized by the three stations "melting,
■ Relatively low investment costs and small space treatment, casting", whereby it is assumed here that
requirement the molten metal is poured by continuous casting. The
■ Largely automatic operation in a simple manner. sequence is then determined by the requirements of
One drawback is the sensitivity of the refractory lining inthe continuous casting plant which, as a rule, is fed con-
an induction furnace, this being characterized by a mini- tinuously with liquid steel via a tundish from a ladle posi-
mal wall thickness and the risk of cracks forming leading tioned above which is emptied through the base. After a
to operational stoppages. Induction furnaces also place pouring time of 40 to max 70 min, the ladle is exchanged
more stringent requirements on the quality of the scrap in 3 to 5 min. During this time, there is sufficient melt
metal than electric arc furnaces. These firstly concern available from the tundish, so that up to 30 sequential
the geometric dimensions which need to be adjusted to charges can be poured without interruption. The tundish
the relatively small surface/volume ratio of the crucible is then exchanged and other maintenance work is per-
furnace: the pieces of scrap metal should not be longer formed, this generally taking around two hours per day.
than half the crucible diameter. The non-metallic con- Melting operations thus face the task of providing a
tents need to be kept in bounds to ensure that the ratio ready-to-pour, liquid charge in a 40 to 65 minute cycle
of slag does not become too great and that the refractory for a period of up to 22 h/day. The design of an induction
melting system suitable for this purpose
is described in the following example
Table 2: Design data for an induction melting installation for the production of construc-
[14]. 300,000 t of construction steel billets
tion steel billets [14]
are to be produced per annum in the fol-
lowing composition:
Annual billet production 300.000 t/a

Working days per year (22 days maintenance, 0.15 - 0.3 % C; 0.6 - 1.6 % Mn; 0.15 - 0.5 %
310 d/a S; P and S < 0.04 %.
23 days standstill at 93.7 % availability)

Output of raw materials 95 %

The feed material is shredded scrap
Returns at 20 charges in sequential casting 3% with a low cast iron content. Table 2 lists
the benchmark data for designing the
Produced melt 310.000 t
induction melting system. The system
Daily melt production 310.000/310 1,000 t/d consists of three crucible furnaces, each
Amount of 46t charges (see below) 22 charges/day with a useful capacity of 23 t, of which
two produce the 46 t charge in melting
Cycle time per charge 24/22 * 60 65 min mode whilst one is held on stand-by

54     heat processing 1-2012

 Induction Technology Reports

Fig. 10: Diagram of an induction melting

facility and the process route for
the production of 300 kt/a of struc
tural steel billets; source: ABP

Fig. 11: Production in the induction

furnace of alloyed steel
heats for further processing
in the AOD converter and
continuous caster [14]

waiting for new refractory to be installed (Figure 10). Production of different types of steel
The connected load per furnace is calculated from the The induction furnace is suitable for producing different
aforesaid cycle time of 65 min; after subtracting 15 min types of steel, from simple construction steel through
for finishing, tapping and first charging, 50 min therefore to high-alloyed special steels. Differing requirements are
remain as melting time. This results in the following thereby placed on both the treatment equipment and
equation for furnace power P: on the melting process, as the following examples show.
When smelting construction steel on the basis of scrap
P = 560 kWh/t • 23 t • 60 min/h / 50 min ≈ 16,000 kW. with a suitable chemical composition, the melt is finished
in the induction furnace without subsequent treatment
The refractory service life is 70 to 100 charges, or 3.2 to and is fed directly to the continuous casting plant [15]. In
4.5 days given 22 charges per day of production. It takes the majority of cases, however, the quality of the scrap
around 1½ days to install new refractory, including sin- metal available requires that a ladle furnace is placed
tering. So even if the refractory service life per furnace is in-between. This desulferizes and deoxidizes the melt,
only three days, two furnaces running in melting mode adjusts its composition and temperature, cleans it with
ensure that on-going melting operations continue with argon bubbles and subsequently finishes it ready for
a reserve furnace on stand-by waiting for new refractory. casting (Fig. 10). In this respect, dephosphorizing and
The two parallel running 23 t melting furnaces then melt decarburizing are an additional task, one performed by
a 46 t charge in 65 min cycles. The melt is then taken for the melting unit "electric arc furnace" by oxygen blowing
treatment in the ladle furnace and from there on to the during the melting process. It is recognized that this is not
continuous casting plant, as shown in Fig. 10. possible in an induction furnace due to the inadmissibly

1-2012 heat processing   55

 
 Reports Induction Technology

vacuum plant) as per Fig. 11 the liquid charges for the

continuous casting plant. In this context, the high yield
of the ferroalloys used in the melting unit can be seen
as the main economic advantage of induction furnaces
compared to electric arc furnaces. A further advantage
results from the relatively high carbon content of such
premelting. In contrast to the cases described above, this
enables a 100 K lower tapping temperature with a cor-
respondingly longer refractory service life, whilst at the
same time consuming less energy.
The particular benefits of melting stainless steels by
induction have been reaped by the Indian steelmaker
Viraj (one of the largest producers of long products made
of stainless steel) for some time now. Due to the positive
Fig. 12: experiences made, an induction melting system is now
Type ABP IFM 30 t being constructed for the works in Tarapur Maharashtra,
crucible furnace for near Mumbai, which will initially consist of three 30 t cru-
18 MW converter cible furnaces each with a connected load of 18 MW. As
rating, installed at can be seen from the plant diagram in Fig. 10, two of the
Viraj, Tarapur, India 30 t furnaces (Fig. 12) run in melting mode and deliver
a 50 t melt charge in hourly cycles. These melts are then
finished in the AOD converter ready for subsequent
high refractory wear which then occurs and the unsuit- continuous casting, as shown by the diagram in Fig. 11.
able surface/volume ratio of the furnace. If decarburizing The third furnace waits for the periodic installation of
and/or dephosphorizing are required due to the qual- new refractory and sintering, as described above in the
ity of the scrap metal, either a special ladle furnace is "Design" section. The next stage of the project foresees
deployed or an electric arc furnace with low connected the installation of two further three-furnace-sets, each of
load is used as treatment equipment. these with a capacity of 47 t, likewise with 18 MW power
When producing alloyed steels, the induction melting supplies.
system delivers together with an AOD converter (or a
Combination of electric arc furnace and
induction furnace
NASCO has operated an induction system in its
electric steel works in Dammam, Saudi Arabia,
since the end of 2008 as an additional melting
unit to the electric arc furnace to produce over
900 kt/a of construction steel [16]. As shown
in Fig.  13, 100 t liquid charges are produced in
55 min cycles. The electric arc furnace melts an
80 t charge (consisting mainly of direct reduced
iron) which is supplemented with 20 t of melt
from the induction furnace. The 100 t charge put
together in this way is treated in the ladle furnace,
as described in the foregoing section, and subse-
quently transported to the four-line continuous
casting facility. The induction system consists of
two 23 t crucible furnaces with a 16 MW/250 Hz-
TWIN-POWER® energy supply fed from a diesel
generator system. One furnace runs in melting
mode whilst the other is kept on stand-by wait-
Fig. 13: Melting of structural steel in the electric arc and the induction
ing for new refractory to be installed. Shredded
furnace; treatment of the common charge in the ladle furnace,
scrap in differing quality is used as melting stock.
followed by continuous casting [14]
The photograph in Fig. 14 shows the crucible
furnace at the front being held in reserve whilst

56     heat processing 1-2012

 Induction Technology Reports

skimming is performed in the second during a trial run. The

charging vehicle can be seen in the foreground, this is
driven backwards for loading with the shredded scrap
depicted in Fig. 15 b underneath one of the two supply
containers (Fig. 15 c). The melting stock is transported
from the scrap yard (Fig. 15 a) in baskets on carriages with
weighing equipment and filled into the supply contain-
ers. Fig. 15 d shows the 12 t capacity charging vehicle
from the rear.
The induction furnace being used for melting opera-
tions is run in charge mode in order to produce 16 to 23 t
charges per hour (depending on the specifications of
the electric arc furnace) at full output, around the clock,
seven days per week. The service life of the refractory lin-
ing made from spinel-forming Al2O3-dry mass meanwhile
averages 100 charges, which is a consumption of 3.25
kg mass per ton of melt. No repairs are needed except Fig. 14: Induction-furnace tandem installed at NASCO STEEL,
minor maintenance work on the pouring spout and in showing a crucible furnace during slag tapping,
the upper section of the furnace. The evenly worn cru- charging car visible in the background [16]
cible is rather pressed out completely with the hydraulic
press-out equipment after around four days in operation.
Whilst the second furnace takes over melting operations the melt in liquid form. The intention is to produce 180t
for the next four days, there is then enough time to install liquid charges in hourly cycles, so that the alloy melts are
new refractory, which can be accomplished in 1½ days in required in quantities of up to 60 t/h. The induction melt-
an emergency. The option of liquid sintering is particu- ing system in question consists of three 65 t tandems,
larly beneficial here, in that the sinter melt is poured from each equipped with an inverter output of 42 MW due to
one furnace to the other from a stopper ladle. the high energy requirement of ferrochrome. In this case,
The shredded scrap used provides the steel melt in the
induction furnace with a composition suitable for pro-
ducing construction steel:

0.233 C/ 0.026 S/ 0.021 P/ 0.613 Mn/ 0.087 Si/ 0.066 Ni/

0.07 Cr/ 0.152 Cu/ 0.005 V/ 0.015 Sn/ 0.005 Al.
After reaching the tapping temperature of 1,650 °C, the
melt is usually poured without skimming into the 100t
ladle and, after filling the 80t EAF charge, fed to the ladle
furnace.
After almost three years of trouble-free operation,
NASCO's induction system has now proved its high avail-
ability and economic efficiency. This is shown in Table 3
by the operating figures for the induction furnace
updated by A. Phillips [16] in comparison to the electric
arc furnace, which demonstrate a cost benefit of 15 US$
per ton of melt.

Melting ferroalloys in the most powerful induc-

tion furnace in the world
The Chinese steelmaker TISCO (Taiyuan Iron Steel Co. Ltd.)
operates a steel works in Taiyuan with an output of 10
Mt/a, of which 3 Mt/a are stainless steels. It is planning Fig. 15: Supply of scrap to the NASCO STEEL induction-furnace installa-
to significantly expand its operations by 2015, this mainly tion: a) scrap storage, b) shredder scrap, c) scrap hopper in front
involving the production of high-alloyed steels. As these of the furnace platform, d) charging car for conveyance of scrap
are to be primarily produced via the route "blast furnace/ to the furnace platform and continuous charging into one of the
oxygen converter", it is necessary to add the ferroalloys to crucible furnaces [16]

1-2012 heat processing   57

 
 Reports Induction Technology

Table 3: Consumption statistics for induction and electric-arc Literature

furnaces, in US $/t [16]
[1] Ameling, D.: Ressourceneffizienz - Stahl ist die Lösung. BDSV
Jahrestagung, Berlin, Sept. 2007
Induction Electric arc
  [2] World Steel Association: Steel Statistical Yearbook 2011
furnace furnace
[3] Krüger, K. und H. Pfeifer: Lichtbogenöfen. In: Pfeifer, H., B.
Shredded scrap 313 310 Nacke und F. Beneke (Hrsg.): Praxishandbuch Thermoproz-
esstechnik, Bd. II, 2. Auflage, Vulkan-Verlag GmbH, Essen,
Electrical energy (IO: 520 kWh/t) 18.7 16.1 2011, pp. 43-80.
Refractory (IO: 100 charges/lining) 6.0 1.6 [4] Stahlfibel, Verlag Stahleisen, Düsseldorf 2002
[5] Ouvradou, C.: European Perspective on the Role of the EAF.
Electrodes 0 9.7
8th European Electric Steelmaking Conference, Birmingham,
Fluxing agent 0 4.7 9-11 May 2005, pp.15-30.
[6] Schliephake, H.,R. Steffen und H.B. Lüngen: Einsatzstoff Eisen-
Oxygen 0 2.3
schwamm und Eisencarbid, pp. 65-76 in: Heinen, K.-H (Hrsg.).:
Alloy materials 5.5 13.4 Elektrostahl-Erzeugung, 4. Auflage, Verlag Stahleisen GmbH,
Düsseldorf, 1997.
  343.2 357.8
[7] Dötsch, E.: Components of a Crucible Furnace Plant, pp. 15-53
in: E. Dötsch: Inductive Melting and Holding. Vulkan-Verlag
GmbH, Essen, 2009.
[8] Dötsch, E.: Fundamentals Induction Crucible Furnace, pp.
too, one furnace in the tandem system will run melting 5-11 in: [7]
mode, the other held on stand-by ready for installing [9] Dötsch, E. und H. Doliwa: Wirtschaftliches Schmelzen in Mit-
telfrequenz-Induktionsöfen. Gießerei 75 (1986), Nr. 17, pp.
new refractory and sintering, whereby separate power
495-501
will be supplied by 2 MW-IGBT inverters. It is planned to
[10] Dötsch, E. und F. Hegewaldt: Schmelzen von Stahl in
commission the first 65 t 42 MW tandem by the end of Großraum-Induktions-Tiegelöfen. Fachberichte Hüttenpraxis
2012. The system represents an enormous leap in the Metallverarbeitung 15 (1977), pp. 429-433.
development of induction furnace technology, breaking [11] Dötsch, E. und H. Gillhaus: Der leise Mittelfrequenz-
new ground for the deployment of such furnaces. Tiegelofen für hohe Schmelzleistungen. ABB Technik (1993)
Nr. 4, pp. 233-238.
Conclusion [12] Dötsch, E.: Refractory Lining, pp. 16-23 in: [7].
Global production of electric steel, in line with total [13] Heinen, K.-H., B. Steffes und H. Zörcher: Sekundärmetallur-
steelmaking across the world, has more or less reco- gie, pp. 513-569 in: [6].
vered from the collapse in 2008/2009, reaching 411 Mt/a [14] Dötsch, E.: Induktionsöfen, pp. 81 – 88 in: Pfeifer, H., B. Nacke
und F. Beneke (Hrsg): Praxishandbuch Thermoprozesstech-
in 2010. Further growth in electric steel is highly likely
nik, Bd. II, 2. Auflage, Vulkan-Verlag GmbH, Essen, 2011,
due to the continued rise of steel production in general pp. 81-88.
and to the greater use of direct reduced iron. Whilst [15] Cabai, F. und P. Lumlay: The Micro Mill – a Solution to Local
the electric arc furnace has been deployed in the Needs, Millenium Steel 2 k 3, pp. 115-118.
past as the traditional melting unit, experiences made [16] Phillips, A.: Motivation to Install Induction Furnace Technol-
with induction furnaces for smelting carbon steels, ogy. 4. BSE Mini Mill Symposium, Schluchsee, April 2009.
although above all alloyed steels, lead one to expect
that the induction furnace will become established as
an alternative electrical melting machine in steel works. Authors
This is particularly attributable to the latest develop-
ments in induction technology, where electric energy
Dipl.-Ing. Mohamed Chaabet
supplies delivering over 40 MW are being built for ABP Induction Systems GmbH
crucible furnaces with capacities of over 65 t. Apart Dortmund, Germany
from the deployment of such high performance induc- Tel.: +49 (0)231/ 997-2451
tion furnaces for melting steel from scrap or even from [email protected]
direct reduced iron in mini-mills, these are also suitable
for melting the ferroalloys which are added into the Dr. Erwin Dötsch
unheated ladle in liquid form during the production ABP Induction Systems GmbH
of stainless steel. It can be forecast with great certainty Dortmund, Germany
that induction technology will build upon its estab- Tel.: +49 (0)231/ 997-2415
lished status in foundries and that a new area of applica- [email protected]
tion will open up with its deployment in steelmaking.

58     heat processing 1-2012