Scribd
Upload
36 views4 pages

Contoh Desain Breakwater Floating

The document describes several models of floating breakwaters produced by SF MARINA: - The SFBW300 is a 3-meter wide concrete breakwater that has been tested over 35 years and works in exposed locations. - The SFBW400 is rigorously tested and has survived storms and hurricanes over 30 years of development. It uses reinforced concrete and a unique stress-absorbing connection system. - The SFBW500 is a 5-meter wide model developed for hurricanes on the U.S. East Coast. Its connection system absorbs and distributes loads during severe storms. - The SFBW600 is the largest at 6 meters wide. It uses patented couplings,

Uploaded by

ghifari
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
36 views4 pages

Contoh Desain Breakwater Floating

The document describes several models of floating breakwaters produced by SF MARINA: - The SFBW300 is a 3-meter wide concrete breakwater that has been tested over 35 years and works in exposed locations. - The SFBW400 is rigorously tested and has survived storms and hurricanes over 30 years of development. It uses reinforced concrete and a unique stress-absorbing connection system. - The SFBW500 is a 5-meter wide model developed for hurricanes on the U.S. East Coast. Its connection system absorbs and distributes loads during severe storms. - The SFBW600 is the largest at 6 meters wide. It uses patented couplings,

Uploaded by

ghifari
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Contoh Desain Breakwater Floating

https://www.sfmarina.com/solutions/breakwaters/

SFBW300
SF300 is a 3-meter wide all-concrete Breakwater. In our experience, 3 meters in
width is minimum for the successful use of the turbulence chamber, “Wings,” the
pontoon. SF300 Series has been developed over 35 years and is now a very well-
tested product that works in exposed locations.

SFBW400
SF400 Series is a very rigorously tested breakwater. It is used today in all the world’s
oceans. SF400 Series has been under continual development for the past 30 years
and has survived all of the recent storms and hurricanes that it has been exposed to.
This is due to our very unique system which has been designed to absorb and
distribute stress when the loads are increasing tremendously during severe storms.
SF400 Series, like all of our breakwaters, is doubly reinforced with the market’s
thickest concrete surfacing layer, which guarantees a strong pontoon with a very
long lifetime. The amount of reinforced concrete in a breakwater is easy to compare
with others, by simply checking the weight.
SFBW500
The SF500 Series is a 5-meter wide super strong breakwater, often found as the outer
pier protection for various port facilities. The SF500 series was initially developed
for the USA’s East Coast where our installations are regularly exposed to the brutal
hurricanes that plague the coast during the autumn season. That our SF500 series
survives this depends on our unique coupling system that absorbs and distributes
loads when the loads are increasing tremendously during severe storms.
Simply put, one can say that when a SF500 breakwater is under duress, the rubber
cylinders in the connectors are what handles the stress, and not the wires, so the
concrete around the connectors is subjected mainly to compressive forces, and not
tension. This makes our breakwater unique and our SF500 series is the foremost
floating breakwater made today.

We can now manufacture them at any angles whatsoever, and we can equip the
pontoons with virtually any components because we basically use the same
standardized technical solutions that are thoroughly tested.
SFBW600
The geometry of this pontoons, in combination with our patented coupling and an
advanced mooring system, makes our floating breakwater an excellent wave
attenuator. This pontoon has been developed gradually over the years. From smaller
sizes in the beginning, now reaching the width of 6 meters, it is the largest model of
floating breakwater on the market. The breakwaters from SF MARINA are all-
concrete pontoons with all the advantages of high stability and buoyancy. The all
concrete and styrofoam construction of the pontoon produces a very high degree of
buoyancy thus making it virtually unsinkable. As a result of the use of high quality
materials, in combination with a thorough manufacturing process, the pontoon
enjoys a long life-span. Each standard pontoon is designed to accept electrical and
water supply services. Normally, the pontoons would be moored using chains and
blocks. This pontoons are first and foremost as a floating breakwater. However, they
can be used universally where the potential of a pontoon having high stability and
freeboard can be utilized.
https://catherinevnukspenserwipperfurth.weebly.com/floating-breakwater-specifications.html

http://www.fdn-engineering.nl/floating-breakwater-in-messolonghi

You might also like