DC/DC Converters: Features
DC/DC Converters: Features
DC/DC Converters: Features
CB
Scheme
UL 60950-1
Features
◆ SMD package
◆ Wide 2:1 input voltage range
◆ I/O isolation 1500VDC
◆ Under voltage lockout
◆ Operating temp. range –40°C to +85°C
◆ Short circuit protection
◆ High accuracy of pin co-planarity
◆ Lead free design – RoHS compliant
◆ 3-years product warranty
Models
Ordercode Input voltage range Output voltage Output current max. Efficiency typ.
TES 3-1210 3.3 VDC 700 mA 75 %
TES 3-1211 5 VDC 600 mA 79 %
9 – 18 VDC
TES 3-1212 12 VDC 250 mA 82 %
(12 VDC nominal)
TES 3-1222 ±12 VDC ±125 mA 81 %
TES 3-1223 ±15 VDC ±100 mA 81 %
TES 3-2410 3.3 VDC 700 mA 76 %
TES 3-2411 5 VDC 600 mA 80 %
18 – 36 VDC
TES 3-2412 12 VDC 250 mA 83 %
(24 VDC nominal)
TES 3-2422 ±12 VDC ±125 mA 82 %
TES 3-2423 ±15 VDC ±100 mA 82 %
TES 3-4810 3.3 VDC 700 mA 76 %
TES 3-4811 5 VDC 600 mA 80 %
36 – 75 VDC
TES 3-4812 12 VDC 250 mA 83 %
(48 VDC nominal)
TES 3-4822 ±12 VDC ±125 mA 82 %
TES 3-4823 ±15 VDC ±100 mA 82 %
http://www.tracopower.com Page 1 of 4
DC/DC Converters
TES 3 Series 3 Watt
Input Specifications
Input current no load / full load 12 Vin models: 20 mA / 300 mA typ.
24 Vin models: 5 mA / 150 mA typ.
48 Vin models: 3 mA / 75 mA typ.
Start-up voltage / 12 Vin models: 6 VDC / 8 VDC typ.
under voltage shut down 24 Vin models: 12 VDC / 16 VDC typ.
48 Vin models: 24 VDC / 32 VDC typ
Surge voltage (1 sec. max.) 12 Vin models: 25 V max.
24 Vin models: 50 V max.
48 Vin models: 100 V max.
Reverse voltage protection 0.5 A max.
Reflected input ripple current can be reduced by ext. 1–2.2 µF polyester film
capacitor
Input filter Pi filter
Output Specifications
Voltage set accuracy ±1 %
Regulation – Input variation Vin min. to Vin max. 0.3 % max.
– Load variation 10 – 100 %
single output models: 1.0 % max.
dual output models balanced load: 1.0 % max.
dual output models unbalanced load: 2.0 % max.
Ripple and noise 50 mVpk-pk max.
Temperature coefficient ±0.02 %/°C
Current limitation >110 % of Iout max., continuouse
Short circuit protection hiccup mode, indefinite
(no automatic recovery)
Capacitive load – single output models 4700 µF
– dual output models 180 µF (each input)
General Specifications
Temperature ranges – Operating –40°C to +85°C
– Case temperature +100°C max.
– Storage –40°C to +125°C
Derating (convection cooling) 3.5 %/K above 70°C
Humidity (non condensing) 95 % rel H max.
Reliability, calculated MTBF (MIL-HDBK-217F, at +25°C, ground benign) >1‘000‘000 h
Isolation voltage (60 sec.) – Input/Output 1‘500 VDC
Isolation capacitance – Input/Output 65 pF typ.
Isolation resistance – Input/Output >1‘000 Mohm
Switching frequency 300 kHz typ. (frequency modulation PFM)
Safety standards UL 60950-1, IEC/EN 60950-1
All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.
http://www.tracopower.com Page 2 of 4
DC/DC Converters
TES 3 Series 3 Watt
Physical Specifications
Casing material non conductive black plastic
(UL 94V-0-rated)
Pin material Phosphor bronze
Package weight 8.8 g (0.31 oz)
Lead-free reflow solder process as per J-STD-020D.1 (to find at:
www.jedec.org - free registration required)
Moisture sensivity level (MSL) level 2 as per J-STD-033B.1 (to find at:
www.jedec.org - free registration required)
Washing process not recommended. Product non-hermetical.
Pin-Out
(0.402)
16.1 (0.634) 3 NC NC
18.8 (0.740)
10 NC Common
11 NC NC
Ø1.5 (Ø 0.06) vent hole on bottom side
(for reflow soldering process)
12 NC –V Output
24.6 (0.97)
13 +V Output +V Output
24 13
14 NC NC
Detail A M10:1
(0.41)
15 –V Output Common
Top View 22 NC NC
4)
10.4
.0
(0
0
1. 23 +Vin (Vcc) +Vin (Vcc)
24 +Vin (Vcc) +Vin (Vcc)
0.15
(0.006)
1 12
1.3 (0.051)
0.15
http://www.tracopower.com Page 3 of 4
DC/DC Converters
TES 3 Series 3 Watt
27.94 (1.1)
1
2.8 (0.11)
1.5 Min.
(0.059 Min.)
Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com
Rev. July 13, 2018
www.tracopower.com Page 4 of 4