MCQs Amplifiers
MCQs Amplifiers
MCQs Amplifiers
Answer :
An operational amplifier, abbreviated as op-amp, is basically a multi-stage, very high gain, direct-
coupled, negative feedback amplifier that uses voltage shunt feedback to provide a stabilized voltage gain.
2. Question2. State Assumptions Made For Analyzing Ideal Op-amp?
Answer :
Assumptions made for analyzing ideal op-amp are:
o Infinite open-loop gain
o Infinite input impedance
o Zero output impedance
o Perfect balance
o Infinite frequency bandwidth
o Infinite slew rate
o Infinite common-mode rejection ratio
o Nil drift of characteristics with temperature
3. Question3. Explain What Are Differential Gain And Common-mode Gain Of A Differential
Amplifier?
Answer :
When the difference of the two inputs applied to the two terminals of a differential amplifier is amplified,
the resultant gain is termed as differential gain. But when the two input terminals are connected to the
same input source then the gain established by the differential amplifier is called the common mode gain.
4. Question4. Define Cmrr?
Answer :
CMRR is defined as the ratio of differential voltage gain to common-mode voltage gain and it is given as
CMRR = Ad/Acm.
5. Question5. Explain Why Does An Op-amp Have High Cmrr?
Answer :
High CMRR ensures that the common mode signals such as noise are rejected successfully and the output
voltage is proportional only to the differential input voltage.
6. Question6. Explain Why Open-loop Op-amp Configurations Are Not Used In Linear Applications?
Answer :
When an op-amp is operated in the open-loop configuration, the output either goes to positive saturation
or negative saturation levels or switches between positive and negative saturation levels and thus clips the
output above these levels. So open-loop op-amp configurations are not used in linear applications.
7. Question7. List The Parameters That Should Be Considered For Ac And Dc Applications?
Answer :
The parameters to be considered for dc applications are:
o Input offset voltage
o Input offset current
o Input bias current
o Drift
The parameters to be considered for ac applications are:
o Gain bandwidth product (GBW)
o Rise time
o Slew rate
o Full-power response
o AC noise
8. Question8. Define Offset Voltage As Applied To An Op-amp?
Answer :
Input offset voltage may be defined as that voltage which is to be applied between the input terminals to
balance the amplifier.
9. Question9. Define Slew Rate?
Answer :
Slew rate of an op-amp is defined as the maximum rate of change of output voltage per unit time and is
expresses in V/µs.
10. Question10. Explain What Is A Voltage Follower?
Answer :
Voltage follower is an electronic circuits in which output voltage tracts the input voltage both in sign and
magnitude.
11. Question11. Explain What Are The Advantages Of Using A Voltage Follower Amplifier?
Answer :
Voltage follower has three unique characteristics viz. extremely high input impedance, extremely low
output impedance and unity transmission gain and is , therefore, an ideal circuit device for use as a buffer
amplifier.
12. Question12. In Explain What Way Is The Voltage Follower A Special Case Of The Non-inverting
Amplifier?
Answer :
If feedback resistor is made zero or R1 is made ∞(by keeping it open-circuited) in a noninverting
amplifier circuit, voltage follower is obtained.
13. Question13. Explain What Is An Inverting Amplifier?
Answer :
In an inverting amplifier, the input is connected to the minus or inverting terminal of op-amp.
14. Question14. Explain What Are The Applications Of An Inverting Amplifier?
Answer :
Inverting amplifier is a very versatile component and can be used for performing number of mathematical
stimulation such as analog inverter, paraphrase amplifier, phase shifter, adder, integrator, and
differentiator.
15. Question15. Explain What Is A Differential Amplifier?
Answer :
Differential amplifier is a combination of inverting and noninverting amplifiers and amplifies the voltage
difference between input lines neither of which is grounded.
16. Question16. Give Examples Of Linear Circuits?
Answer :
Adder, subtractor, differentiator, integrator fall under the category of linear circuits.
17. Question17. Explain What Is An Adder Or Summing Amplifier?
Answer :
Adder or summing amplifier is a circuit that provides an output voltage proportional to or equal to the
algebraic sum of two or more input voltages multiplied by a constant gain factor.
18. Question18. Explain What Is An Integrator?
Answer :
An integrator is a circuit that performs a mathematical operation called integration.
19. Question19. Explain What Are The Applications Of Integrator?
Answer :
Integrators are widely used in ramp or sweep generators, filters, analog computers etc.
20. Question20. Op-amp Is Used Mostly As An Integrator Than A Differentiation. Explain Why?
Answer :
Op-amp is used mostly as an integrator than a differentiator because in differentiator at high frequency,
gain is high and so high-frequency noise is also amplified which absolutely abstract the differentiated
signal.
21. Question38. Explain What Are The Main Purposes For Which A Common-collector Amplifier May
Be Used?
Answer :
For a common collector amplifier, current gain is as high as for CE amplifier, voltage gain is less than
unity, input resistance is the highest and the output resistance is the lowest of all the three (CE, ,CC and
CB) configurations. This circuit finds wide applications as a buffer amplifier between a high impedance
source and a low load.
--------------
Multiple Choice Questions and Answers on Amplifiers with Negative Feedback
Q1. When negative voltage feedback is applied to an amplifier, its voltage gain ……………….
1. Is increased
2. Is reduced
3. Remains the same
4. None of the above
Answer : 2
Q2. The value of negative feedback fraction is always …………….
1. Less than 1
2. More than 1
3. Equal to 1
4. None of the above
Answer : 1
Q3. If the output of an amplifier is 10 V and 100 mV from the output is fed back to the input, then
feedback fraction is ………..
1. 10
2. 1
3. 01
4. 15
Answer : 3
Q4. The gain of an amplifier without feedback is 100 db. If a negative feedback of 3 db is applied, the
gain of the amplifier will become …………..
1. 5 db
2. 300 db
3. 103 db
4. 97 db
Answer : 4
Q5. If the feedback fraction of an amplifier is 0.01, then voltage gain with negative feedback is
approximately………..
1. 500
2. 100
3. 1000
4. 5000
Answer : 2
Q6. A feedback circuit usually employs ……………… network
1. Resistive
2. Capacitive
3. Inductive
4. None of the above
Answer : 1
Q7. The gain of an amplifier with feedback is known as ………….. gain
1. Resonant
2. Open loop
3. Closed loop
4. None of the above
Answer : 3
Q8. When voltage feedback (negative) is applied to an amplifier, its input impedance ………….
1. Is decreased
2. Is increased
3. Remains the same
4. None of the above
Answer : 2
Q9. When current feedback (negative) is applied to an amplifier, its input impedance …………..
1. Is decreased
2. Is increased
3. Remains the same
4. None of the above
Answer : 1
Q10. Negative feedback is employed in ……………..
1. Oscillators
2. Rectifiers
3. Amplifiers
4. None of the above
Answer : 3
Q11. Emitter follower is used for …………
1. Current gain
2. Impedance matching
3. Voltage gain
4. None of the above
Answer : 2
Q12. The voltage gain of an emitter follower is ………..
1. Much less than 1
2. Approximately equal to 1
3. Greater than 1
4. None of the above
Answer : 2
Q13. When current feedback (negative) is applied to an amplifier, its output impedance ……..
1. Is increased
2. Is decreased
3. Remains the same
4. None of the above
Answer : 1
Q14. Emitter follower is a ……………….. circuit
1. Voltage feedback
2. Current feedback
3. Both voltage and current feedback
4. None of the above
Answer : 2
Q15. If voltage feedback (negative) is applied to an amplifier, its output impedance …………..
1. Remains the same
2. Is increased
3. Is decreased
4. None of the above
Answer : 3
Q16. When a negative voltage feedback is applied to an amplifier, its bandwidth……….
1. Is increased
2. Is decreased
3. Remains the same
4. Insufficient data
Answer : 1
Q17. An emitter follower has ………… input impedance
1. Zero
2. Low
3. High
4. None of the above
Answer : 3
Q18. This question will be available soon