Designation: A924/A924M − 14

Standard Specification for

General Requirements for Steel Sheet, Metallic-Coated by
the Hot-Dip Process1
This standard is issued under the fixed designation A924/A924M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.

1. Scope* 1.5 In case of any conflict in requirements, the requirements

1.1 This specification covers the general requirements that, of the individual product specifications shall prevail over those
unless otherwise specified in the product specification, apply to of this general specification.
steel sheet in coils and cut lengths, metallic-coated on continu- 1.6 The purchaser is permitted to specify additional require-
ous lines by the hot-dip process. The product is intended for ments that do not negate any of the provisions of this general
applications requiring corrosion resistance. The product speci- specification or of the individual product specifications. Such
fications contain requirements for specific strength levels, heat additional requirements, the acceptance of which are subject to
resistance, paintability, or formability, or a combination negotiation with the supplier, shall be included in the order
thereof. information.
1.2 Subject to individual product specification provisions,
1.7 For purposes of determining conformance with this
steel sheet is available as Commercial Steel (CS) Types A, B,
specification and the various product specifications referenced
and C, Forming Steel (FS), Drawing Steel (DS), Deep Drawing
Steel (DDS), Extra Deep Drawing Steel (EDDS), High Tem- in 1.3, values shall be rounded to the nearest unit in the
perature Steel (HTS), Structural Steel (SS), and High Strength right-hand place of figures used in expressing the limiting
Low Alloy Steel (HSLAS). Steel sheet is produced with the values (except to the nearest 5 MPa for SI strength values) in
following metallic coatings. Specific information on each of accordance with the rounding method of Practice E29.
the following is contained in the individual product specifica- 1.8 Metallic-coated steel sheet covered by this specification
tion: is produced to thickness requirements expressed to 0.001 in.
1.2.1 Zinc or zinc-iron alloy coated, [0.01 mm] for both coils and cut lengths. The thickness is the
1.2.2 Zinc-5 % aluminum alloy coated, total of the base steel and the coating.
1.2.3 55 % aluminum–zinc alloy coated,
1.9 The text of this specification references notes and
1.2.4 Aluminum–coated,
footnotes that provide explanatory material. These notes and
1.2.5 Terne (lead-tin alloy) coated, and footnotes (excluding those in tables and figures) shall not be
1.2.6 Zinc-aluminum-magnesium alloy coated. considered as requirements of the specification.
1.3 Products covered by this general requirements specifi- 1.10 The values stated in inch-pound units or SI units are to
cation are described in the following product standards: Speci- be regarded separately as standard. Within the text, the SI units
fications A308/A308M; A463/A463M; A653/A653M; A755/ are shown in brackets. The values stated in each system are not
A755M; A792/A792M; A875/A875M; A929/A929M; A1046/
exact equivalents; therefore, each system must be used inde-
A1046M; A1057/A1057M; A1063/A1063M; and A1079.
pendently of the other.
1.4 Metallic-coated steel sheet is produced to various coat-
1.11 This specification and some of the applicable product
ing designations, as shown in the individual product specifica-
tions. Except for differentially coated sheet, the coating is specifications are expressed in both inch-pound and SI units.
always expressed as the total coating of both surfaces. However, unless the order specifies the applicable “M” speci-
fication designation (SI units), the product shall be furnished to
inch-pound units.
1
This specification is under the jurisdiction of ASTM Committee A05 on 1.12 This standard does not purport to address all of the
Metallic-Coated Iron and Steel Products and is the direct responsibility of Subcom- safety concerns, if any, associated with its use. It is the
mittee A05.11 on Sheet Specifications. responsibility of the user of this standard to establish appro-
Current edition approved Oct. 1, 2014. Published October 2014. Originally
approved in 1994. Last previous edition approved in 2013 as A924/A924M - 13. priate safety and health practices and determine the applica-
DOI: 10.1520/A0924_A0924M-14. bility of regulatory limitations prior to use.

*A Summary of Changes section appears at the end of this standard

Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States

1
 A924/A924M − 14
2. Referenced Documents E376 Practice for Measuring Coating Thickness by
2 Magnetic-Field or Eddy-Current (Electromagnetic) Test-
2.1 ASTM Standards:
ing Methods
A90/A90M Test Method for Weight [Mass] of Coating on
2.2 Federal Standard:4
Iron and Steel Articles with Zinc or Zinc-Alloy Coatings
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
A308/A308M Specification for Steel Sheet, Terne (Lead-Tin
Alloy) Coated by the Hot-Dip Process 3. Terminology
A309 Test Method for Weight and Composition of Coating
3.1 Definitions—For definitions of items used in this
on Terne Sheet by the Triple-Spot Test
specification, refer to Terminology A902.
A370 Test Methods and Definitions for Mechanical Testing
of Steel Products 4. Ordering Information
A428/A428M Test Method for Weight [Mass] of Coating on
4.1 Ordering information for all products are shown in the
Aluminum-Coated Iron or Steel Articles individual product specifications.
A463/A463M Specification for Steel Sheet, Aluminum-
Coated, by the Hot-Dip Process 5. Materials and Manufacture
A653/A653M Specification for Steel Sheet, Zinc-Coated
5.1 Hot-dip metallic coatings are used to provide corrosion
(Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) protection to steel sheets. Hot-dip metallic coatings are avail-
by the Hot-Dip Process able in six different types, zinc and zinc-iron alloy, lead-tin
A700 Practices for Packaging, Marking, and Loading Meth- alloy (Terne), aluminum, 55 % aluminum-zinc alloy, zinc-5 %
ods for Steel Products for Shipment (Withdrawn 2014)3 aluminum alloy, and zinc-aluminum-magnesium alloy. Each
A751 Test Methods, Practices, and Terminology for Chemi- coating type is available in various coating weights which
cal Analysis of Steel Products provide varying degrees of corrosion protection and the con-
A754/A754M Test Method for Coating Weight (Mass) of sumer should consult the individual producers for applicability
Metallic Coatings on Steel by X-Ray Fluorescence to the intended application and to obtain product information.
A755/A755M Specification for Steel Sheet, Metallic Coated
by the Hot-Dip Process and Prepainted by the Coil- 5.2 Hot-dip metallic coated products may be subject to
changes in mechanical properties after coating. As such
Coating Process for Exterior Exposed Building Products
changes are functions of the chemistry and processing history
A792/A792M Specification for Steel Sheet, 55 %
of the material, the consumer should consult the individual
Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
producers for applicability to the intended application.
A875/A875M Specification for Steel Sheet, Zinc-5 % Alu-
minum Alloy-Coated by the Hot-Dip Process 6. Chemical Composition
A902 Terminology Relating to Metallic Coated Steel Prod-
6.1 Base Steel:
ucts
6.1.1 Chemical composition requirements of the base steel
A929/A929M Specification for Steel Sheet, Metallic-Coated
are shown in the individual product specifications.
by the Hot-Dip Process for Corrugated Steel Pipe
6.1.2 An analysis of each heat shall be made by the
A1030/A1030M Practice for Measuring Flatness Character-
manufacturer to determine the percentage of carbon,
istics of Steel Sheet Products
manganese, phosphorus, sulfur, and any other elements speci-
A1046/A1046M Specification for Steel Sheet, Zinc-
fied or restricted by the individual product specification.
Aluminum-Magnesium Alloy-Coated by the Hot-Dip Pro-
6.1.3 When desired, product analysis shall be made by the
cess purchaser on finished product. The product analysis so deter-
A1057/A1057M Specification for Steel, Structural Tubing, mined shall meet the tolerances shown in Table 1.
Cold Formed, Welded, Carbon, Zinc-Coated (Galvanized) 6.1.3.1 Capped or rimmed steels are not technologically
by the Hot-Dip Process suited to product analysis due to the nonuniform character of
A1063/A1063M Specification for Steel Sheet, Twin-Roll their chemical composition, and therefore, the tolerances in
Cast, Zinc-Coated (Galvanized) by the Hot-Dip Process Table 1 do not apply. Product analysis is appropriate on these
A1079 Specification for Steel Sheet, Complex Phase (CP), steels only when misapplication is apparent.
Dual Phase (DP) and Transformation Induced Plasticity 6.1.3.2 Product analysis for phosphorus or sulfur is not
(TRIP), Zinc-Coated (Galvanized) or Zinc-Iron Alloy- technologically appropriate because of segregation of these
Coated (Galvannealed) by the Hot-Dip Process elements in non-killed steels. Product analysis is appropriate
E29 Practice for Using Significant Digits in Test Data to only when misapplication is apparent.
Determine Conformance with Specifications 6.1.3.3 Samples for product analysis shall be drillings
through areas stripped free of coating. At least three pieces
shall be selected, but if the product of more than one mill lift
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or or coil is involved, at least six pieces shall be selected.
contact ASTM Customer Service at [email protected]. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
4
the ASTM website. Available from Yale University Library, Standardization Documents Order
3
The last approved version of this historical standard is referenced on Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111–5094, Attn:
www.astm.org. NPODS.

2
 A924/A924M − 14
TABLE 1 Product Analysis Tolerances determine the method to be used; however, in the event of a
Tolerance dispute the method in 7.2.1.2 shall be used.
Limited or Maximum of Under Over
Element
Specified Element, % Minimum Maximum
7.2.1.2 The base metal thickness shall be determined by
Limit Limit stripping the coating from the ends of the specimen contacting
Carbon To 0.15, incl 0.02 0.03 the grips of the tension testing machine. The thickness mea-
Over 0.15 to 0.40, incl 0.03 0.04
Over 0.40 to 0.80, incl 0.03 0.05
surement shall be made before testing on an end of the
Manganese To 0.60, incl 0.03 0.03 specimen that has been stripped free of coating.
Over 0.60 to 1.15, incl 0.04 0.04 7.2.1.3 The base metal thickness shall be determined by
Over 1.15 to 1.65, incl 0.05 0.05
Phosphorus ... ... 0.01 subtracting the coating thickness from the measured thickness
Sulfur ... ... 0.01 of the tension test specimen. The coating thickness shall be
Silicon To 0.30, incl 0.02 0.03 calculated from the coating weight [mass] test.
Over 0.30 to 0.60 0.05 0.05
Copper ... 0.02 ...
Titanium To 0.10, incl 0.01A 0.01 8. Tests for Coating Properties
Vanadium To 0.10, incl 0.01A 0.01
Over 0.10 to 0.25, incl 0.02 0.02 8.1 Coating Weight [Mass]:
Minimum only specified 0.01 ...
Columbium To 0.10, incl 0.01A 0.01
8.1.1 Coating weight [mass] shall conform to the require-
A
If the minimum of the range is 0.01 %, the under tolerance is 0.005 %.
ments prescribed in the individual product specifications (see
1.3).
8.1.2 The coating weight [mass] is ordered as total both
sides requirements, or if requested on those product specifica-
tions permitting it, to single side/single spot coating mass
6.1.3.4 When supplying High-Strength Low-Alloy Steel requirements.
(HSLA), some producers use one or more microalloying 8.1.3 Total both sides requirements
elements as strengthening agents or use alloy additions to effect 8.1.3.1 The coating weight [mass] of equally coated product
inclusion control, or both. The producer shall be consulted for is the total amount on both sides of the sheet, expressed in
the specific chemical composition applied. If any alloying ounces per square foot [grams per square metre] of sheet.
addition is known to be of concern to the user, the producer
8.1.3.2 For differentially coated product, the coating weight
shall be notified of this concern.
[mass] on each surface is nominally one half of the stated
6.1.4 Method of Analysis—The determination of chemical
coating designation.
composition is permitted to be made by any test method,
except in case of dispute, where the referee test methods listed 8.1.4 Single side/single spot requirements
in the section on test methods of Test Methods A751 shall be 8.1.4.1 The coating mass for each surface shall be specified
used. separately, for example, 60G60G, and each single spot test
shall meet the specified requirements for the coating designa-
6.2 Coating: tion.
6.2.1 Coating Analysis—The nominal composition of the
coating is described in the individual product specification. 8.2 Coating Weight [Mass] Tests—One of the following test
6.2.2 Method of Analysis—The determination of chemical methods shall be used:
composition shall be made in accordance with acceptable 8.3 Weigh-Strip-Weigh Method:
chemical, spectrochemical, or other test methods. 8.3.1 The weigh-strip-weigh method, described in Test
Methods A90/A90M, A309, and A428/A428M, is a destructive
7. Tests for Mechanical Properties
test that determines coating weight [mass] by measuring the
7.1 Test specimens shall be prepared from finished metallic- difference in weight [mass] between a coated and a stripped
coated product. (uncoated) sample. If one surface is protected suitably during
7.2 Mechanical Properties-Base Metal—When base metal the initial stripping, coating weight [mass] can be determined
mechanical properties are specified, tests shall be conducted in for each surface independently.
accordance with Test Methods A370. Requirements for all 8.3.2 Test specimens for product over 18 in. [450 mm] in
mechanical properties are included in the individual product width shall be taken from a representative sample piece
specifications. approximately 1 ft [300 mm] in length by the associated width.
7.2.1 Tension Tests—Specimens for base-metal tension tests Three test specimens shall be taken from the sample, one from
shall be taken longitudinally, approximately midway between the middle of the width and one from each edge. The edge
the center and edge of the product as rolled, and shall conform samples shall not be taken closer than 2 in. [50 mm] from each
to the requirements for the sheet-type test specimen in the edge. The test specimen shall have a minimum area of 5
figure for rectangular tension test specimens of Test Methods in.2 [3200 mm2].
A370. 8.3.3 For product 18 in. [450 mm] in width and narrower,
7.2.1.1 The determination of the yield strength and tensile only one test specimen is required. Specimens shall be at least
strength values shall be based on the as-produced base-metal 2 in. [50 mm] from the edge, when possible. For product
thickness that shall be obtained by one of the following narrower than 2.25 in. [60 mm] the test specimen shall be
methods. Unless specified in the order, the producer shall chosen to give a minimum area of 5 in.2 [3200 mm2].

3
 A924/A924M − 14
8.3.4 The triple-spot coating weight [mass] shall be the average of the center, and the average of the other edge. These
average of the determinations of the three tests done in three results shall then be averaged to obtain the triple-spot
accordance with the procedures in 8.3.2. average of the coil.
8.3.5 The total both sides minimum single-spot coating 8.4.3.2 The total both sides minimum single-spot coating
weight [mass] shall be that test result that is the lightest coating weight [mass] shall be the lightest coating weight [mass]
weight [mass], or in those cases where only one test is needed, obtained from the individual edge, center, edge measurements
it shall be that single test result. provided by the minimum five full width traverses (lightest of
8.3.6 The single side/single spot coating mass shall meet at least fifteen readings—five from one edge, five from the
both the lower and upper limits of the specified coating center, and five from the other edge).
designation. 8.4.3.3 The single side/single spot minimum coating mass
8.3.7 The frequency of sampling shall be sufficient to shall be the lightest coating mass obtained from the readings
adequately characterize the lot of material being tested. provided by the minimum five full width traverses.
8.4 X-Ray Fluorescence Method: 8.4.3.4 The single side/single spot maximum coating mass
8.4.1 The X-ray fluorescence method is a nondestructive shall be the heaviest coating mass obtained from the readings
test that determines coating weight [mass] by converting X-ray provided by the minimum five full width traverses.
fluorescence measurements to coating weight [mass] values. 8.5 Coating Bend Test—Refer to the individual product
X-ray fluorescence gages can be used as off-line laboratory specification.
instruments or as a means of continuous on-line testing for 8.5.1 Coating bend test specimens shall be 2 to 4 in. [50 to
conformance to coating weight [mass] requirements, or both. 100 mm] wide. The specimen shall be cut not less than 2 in. [50
8.4.2 Off-Line Testing—X-ray fluorescence gages can be mm] from the edges of the test sheet.
used as off-line laboratory instruments to test for coating
weight [mass] provided that they have been calibrated in 9. Dimensions and Permissible Variations
accordance with Test Method A754/A754M and use the 9.1 The permissible variations for dimensions shall comply
sample test locations as described in 8.3.2 or 8.3.3. with the applicable limits in Tables 2-15.
8.4.3 On-Line Testing—When X-ray fluorescence gages are
used for on-line testing, they shall be operated in accordance 9.2 The table of tolerances for thickness for measurements
with Test Method A754/A754M. A minimum of five random taken 3⁄8 in. from the edge are found in the Supplementary
full-width traverses shall be used to characterize each coil Requirements Section S1 of this specification. See the appro-
tested. priate product specification for instructions on how to specify
8.4.3.1 The triple-spot coating weight [mass] of a coil shall this table.
be determined using the following procedure: from the indi- 9.3 Coil Winding:
vidual edge, center, edge readings provided by the minimum 9.3.1 Metallic coated coils are typically wound with the
five full width traverses, compute the average of one edge, the intention that the sidewalls be nominally straight, i.e., that the

TABLE 2 Thickness Tolerances for Hot-Dip Metallic-Coated Sheet—1-in. [25–mm] Minimum Edge Distance
NOTE 1—The coated sheet thickness includes the base metal and coating and is measured at any point across the width of the coated sheet not less
than 1 in. [25 mm] from a side edge.
NOTE 2—Micrometers used for measurement of thickness shall be constructed with anvils and spindles having minimum diameters of 0.188 in. [4.80
mm]. The tip of the anvil shall be flat or rounded with a minimum radius of curvature of 0.10 in. [2.55 mm] and the tip of the spindle shall be flat.
Micrometers with conical tips shall not be used for thickness measurements of sheet steels.
Inch-Pound Units
Specified Width, in. Specified Ordered Thickness, in.A
0.023 and thin- Over 0.023 Over 0.043 Over 0.061 Over 0.075 Over 0.101 Over 0.187 Over 0.229
ner through 0.043 through 0.061 through 0.075B through 0.101 through 0.187 through 0.229 through 0.250
Thickness Tolerances, Over, in., No Tolerance UnderC
To 32, inclusive 0.003 0.004 0.005 0.006 0.010 0.012 0.014 0.018
Over 32 to 40, inclusive 0.003 0.004 0.005 0.006 0.012 0.012 0.014 0.018
Over 40 to 60, inclusive 0.003 0.004 0.005 0.006 0.012 0.014 0.016 0.020
Over 60 to 72, inclusive 0.003 0.004 0.005 0.006 0.014 0.014 0.018 0.022
SI Units
Specified Width, mm Specified Ordered Thickness, mmA
0.4 and thinner Over 0.4 Over 1.0 Over 1.5 Over 2.0 Over 2.5 Over 5.0 Over 6.0
through 1.0, inclu- through 1.5, through 2.0, through 2.5, through 5.0, through 6.0, through 6.3,
sive inclusive inclusiveB inclusive inclusive inclusive inclusive
Thickness Tolerances, Over, mm, No Tolerance UnderC
To 1500, inclusive 0.08 0.10 0.13 0.15 0.30 0.34 0.42 0.50
Over 1500 0.08 0.10 0.13 0.15 0.34 0.34 0.46 0.52
A
The specified thickness range captions apply independently of whether the ordered thickness is stated as a nominal or minimum. B
B
If hot rolled substrate is used, it is permissible for the seller to provide total thickness tolerance 0.009 in. [0.23 mm], provided that the purchaser is notified and agrees.
C
The tolerances provided in the table are based on minimum thickness (tolerance over, no tolerance under). For nominal thickness, the tolerance is divided equally over
and under (tolerance over, tolerance under).

4
 A924/A924M − 14
TABLE 3 Width Tolerances for Hot-Dip Metallic-Coated Sheet, TABLE 5 Camber Tolerances for Hot-Dip Metallic-Coated Sheet
Coils, and Cut Lengths, Not Resquared
NOTE 1—Camber is the greatest deviation of a side edge from a straight
Inch-Pound Units line, the measurement being taken on the concave side with a straightedge.
Specified Width, in. Tolerance Over Specified
Width, No Tolerance NOTE 2—The camber tolerances for sheet in cut lengths, not resquared,
Over Through
Under, in. are as shown in this table.
12 30 18 ⁄ Inch-Pound Units
30 48 ⁄
3 16
For Coils Over 12 in. in Width
48 60 14 ⁄ Cut Length, ft
60 72 ⁄
5 16 Camber Tolerance,A in.
Over Through
SI Units ... 4 1⁄ 8
Specified Width, mm Tolerance Over Specified 4 6 3⁄16
Over Through Width, No Tolerance 6 8 1⁄ 4
Under, mm 8 10 5⁄16
300 600 3 10 12 3⁄ 8
600 1200 5 12 14 1⁄ 2
1200 1500 6 14 16 5⁄ 8
1500 1800 8 16 18 3⁄ 4

18 20 7⁄ 8

20 30 11⁄4
TABLE 4 Length Tolerances for Hot-Dip Metallic-Coated Sheet, 30 40 11⁄2
SI Units
Cut Lengths, Not Resquared
For Coils Over 300 mm in Width
Inch-Pound Units Cut Length, mm
Camber Tolerance,B mm
Specified Length, in. Tolerance Over Specified Over Through
Length, No Tolerance ... 1200 4
Over Through 1200 1800 5
Under, in.
1800 2400 6
12 30 ⁄
18
2400 3000 8
30 60 ⁄
14
3000 3700 10
60 96 1⁄ 2
3700 4300 13
96 120 3⁄ 4
4300 4900 16
120 156 1 4900 5500 19
156 192 11⁄4 5500 6000 22
192 240 11⁄2 6000 9000 32
240 ... 13⁄4 9000 12 200 38
SI Units
A
Specified Length, mm Tolerance Over Specified The camber tolerance for sheet in coils is 1 in. in any 20 ft, except as shown in
Over Through Length, No Tolerance Table 14.
B
Under, mm The camber tolerance for sheet in coils is 25 mm in any 6000 mm, except as
300 1500 6 shown in Table 14.
1500 3000 20
3000 6000 35
6000 ... 45
TABLE 6 Diameter Tolerances for Hot-Dip Metallic-Coated Sheet,
Sheared Circles
edges of each lap in the coil be nominally flush with each other Inch-Pound Units
throughout both walls of the coil. However, circumstances Tolerance Over Specified Diameter, No
Specified Thickness, in. Tolerance Under, in.
sometimes make it necessary to produce coils that have an
Diameters
intentional, back and forth, cyclic, stagger wound pattern on
Over Through Under 30 30 through 48 Over 48
both sidewalls throughout the entire coil. The purchaser should
... 0.61 ⁄
1 16 1 ⁄8 3⁄16
contact the producer regarding any required limits on, or need 0.061 0.101 3⁄32 5⁄32 7⁄32

for, stagger wound coils. 0.101 ... 1 ⁄8 3⁄16 1 ⁄4

SI Units
9.4 Flatness Tolerances: Tolerance Over Specified Diameter, No
9.4.1 Flatness tolerances for sheet are contained in Table 9 Specified Thickness, mm Tolerance Under, mm
Diameters
and in Table 10 for sheet specified to restricted flatness. Tables Over Through Through 600 Over 600 Over 1200
11 and 12 contain flatness tolerances for SS, HSLAS, and Through 1200
HSLAS-F. ... 1.5 1.5 3.0 5.0
1.5 2.5 2.5 4.0 5.5
9.4.2 Measurement techniques for flatness characteristics 2.5 ... 3.0 5.0 6.5
are described in Practice A1030/A1030M.
9.4.3 Two alternative methods for flatness determination are
the use of I-Units and % Steepness. A description of these two 10. Finish and Condition
alternative methods is contained in Practice A1030/A1030M.
9.4.3.1 The use of I-Units or % Steepness as a flatness 10.1 Metallic-coated sheet intended for applications where
standard is subject to negotiation between the purchaser and surface appearance and controlled surface texture is of primary
the producer. importance shall be ordered as “extra smooth”.
9.4.3.2 Measurement techniques for I-Units and % Steep- 10.2 Metallic-coated sheet, when ordered as regular spangle
ness and rejection limits are subject to negotiation between the or minimized spangle, is not subject to restrictions on surface
purchaser and producer. texture.

5
 A924/A924M − 14
TABLE 7 Out-of-Square Tolerances for Hot-Dip Metallic-Coated TABLE 10 Flatness Tolerances Specified to Restricted Flatness
Sheet Cut Lengths, Not Resquared for Hot-Dip Metallic-Coated Sheet, Cut Lengths
NOTE 1—Out-of-square is the greatest deviation of an end edge from a NOTE 1—This table applies to all designations except SS, HSLAS and
straight line at right angles to a side and touching one corner. It is also HSLAS-F.
obtained by measuring the difference between the diagonals of the cut Inch-Pound Units
length. The out-of-square deviation is one half of that difference.
Specified Specified Specified Flatness
Inch-Pound Units Thickness, in. Width, in. Length, in. Tolerance,A in.
For Coils Over 12 in. in Width Over 0.019 over 12 through 36 through 120, inclusive ⁄
14

The tolerance for cut lengths of all thicknesses and all sizes is 1⁄16 in. in each 6 through 0.032
in. of width or fraction thereof. wider or longer 38⁄
SI Units Over 0.032 over 12 through 48 through 120, inclusive 18⁄
The tolerances for cut lengths of all thicknesses and all sizes is 1.0 mm in each wider or longer 1 ⁄4

100 mm of width or fraction thereof. SI Units

Specified Specified Specified Flatness
Thickness, mm Width, mm Length, mm Tolerance,A
mm
TABLE 8 Resquared Tolerances for Hot-Dip Metallic-Coated 0.35 through 0.8 through 900 through 3000 8
Sheet wider or longer 10
Over 0.8 through 1200 through 3000 5
NOTE 1—When cut lengths are specified resquared, the width and wider or longer 8
length are not less than the dimensions specified. The individual tolerance A
Maximum deviation from a horizontal flat surface.
for over-width, over-length, camber, or out-of-square shall not exceed the
stated values.
Inch-Pound Units TABLE 11 Structural Steel—Flatness Tolerances (Cut Lengths
For Cut-lengths Over 12 in. in Width Only)
Shall not exceed 1⁄16 in. for cut lengths up to and including 48 in. in width and
up to and including 120 in. in length. For cut lengths wider or longer the appli-
NOTE 1—This table also applies to sheets cut to length from coils by the
cable tolerance is 1⁄8 in. consumer when adequate flattening measures are performed.
SI Units
NOTE 2—For Grade 50 [340] (Classes 1, 2, 3, and 4) use 11⁄2 times the
Shall not exceed 1.6 mm for cut lengths up to and including 1200 mm in width
and up to and including 3000 mm in length. For cut lengths wider or longer, the values given in this table.
applicable tolerance is 3.2 mm.
NOTE 3—For Grade 80 [550], there are no defined flatness standards.
Specified Thickness, Specified Flatness Tolerance
in. [mm] Width, in. [mm] (Maximum Deviation
TABLE 9 Flatness Tolerances for Hot-Dip Metallic-Coated Sheet, from a Horizontal
Cut Lengths Flat Surface), in.
[mm]
NOTE 1—This table applies to all designations except SS, HSLAS and Over 0.060 [1.5] to 60 [1500], inclusive 1⁄2 [12]

HSLAS-F. over 60 [1500] to 72 [1800], inclu- 3⁄4 [20]

sive
NOTE 2—This table also applies to sheet cut to length from coils by the 0.060 [1.5] and thin- to 36 [900], inclusive ⁄ [12]
12

consumer when adequate flattening measures are performed ner

Inch-Pound Units over 36 [900] to 60 [1500], inclu- ⁄ [20]
34

sive
Specified Specified Width, in. Flatness over 60 [1500] to 72 [1800], inclu- 1 [25]
Thickness, in. Over Through Tolerance,A in. sive
Through 0.048 12 36 38⁄
36 60 58⁄
60 72 7 ⁄8

Over 0.048 12 36 1 ⁄4 with the thickness of the sheet. Other factors also affect this
36 60 3 ⁄8 tendency for coil breaks. The consumer should contact the
60 72 5 ⁄8
individual producer for the applicability of the intended appli-
SI Units
Specified Specified Width, mm Flatness cation.
Thickness, mm Over Through Tolerance,A mm
Through 1.0 300 900 10 11. Oiling
900 1500 15
1500 ... 20 11.1 Metallic-coated products covered by this specification
Over 1.0 300 900 8 can be furnished oiled or not oiled as specified.
900 1500 10
1500 1800 15 12. Workmanship
1800 ... 20
A
Maximum deviation from a horizontal flat surface. 12.1 Surface Conditions:
12.1.1 Metallic-coated cut lengths (sheets) shall have a
workmanlike appearance and shall not have imperfections of a
nature or degree for the product, grade, class, and designation
10.3 Coil breaks, strain, and fluting may occur in such ordered that will be detrimental to the fabrication, or
materials and the consumer should contact the individual functionality, or both, of the finished part.
producer for applicability to the intended application. 12.1.2 Metallic-coated coils may contain some abnormal
10.4 Metallic-coated sheet in coils is subject to coil breaks imperfections that render a portion of the coil unusable since
when coiled to a smaller inside diameter than is compatible the inspection of coils does not afford the producer the same

6
 A924/A924M − 14
TABLE 12 High-Strength Low-Alloy Steel and High-Strength Low- TABLE 14 Length Tolerances—Narrow Widths for Hot-Dip
Alloy Steel with Improved Formability—Flatness Tolerances (Cut Metallic-Coated Sheet, Cut Lengths, Not Resquared
Lengths Only)
NOTE 1—This table applies to widths of 2 to 12 in. [50 to 300 mm] incl,
NOTE 1—This table also applies to sheets cut to length from coils by the that have been produced by slitting from wider sheet.
consumer when adequate flattening measures are performed. Inch-Pound Units
Inch-Pound Units Specified Length, in. Tolerance Over Specified
Specified Specified Flatness Tolerances (Maximum Devia- Length, No Tolerance
Thickness, Width, in. tion Over Through Under, in.
in. from a Horizontal Flat Surface), in. from 24 60 1⁄ 2

Grade 60 120 3⁄ 4

40 50 55 (Classes 1 70 80 120 240 1

and 2) SI Units
60 Specified Length, mm Tolerance Over Specified
Over to 60, inclusive 5⁄ 8 3 ⁄4 7 ⁄8 1 1 1⁄ 8 Length, No Tolerance
0.060 Over Through Under, mm
over 60 1 11⁄8 1 1⁄4 1 3⁄ 8 1 1⁄ 2 600 1500 15
0.060 and to 36, inclusive 5⁄ 8 3 ⁄4 7 ⁄8 1 1 1⁄ 8 1500 3000 20
thinner 3000 6000 25
over 36 to 60, inclusive 1 11⁄8 1 1⁄4 1 3⁄ 8 1 1⁄ 2
over 60 13⁄8 11⁄2 1 5⁄8 1 3⁄ 4 1 7⁄ 8
SI Units
Flatness Tolerances (Maximum Devia- TABLE 15 Camber Tolerances—Narrow Widths for Hot-Dip
tion Metallic-Coated Sheet, in Coils
from a Horizontal Flat Surface), mm
Grade NOTE 1—This table applies to widths of 2 to 12 in. [50 to 300 mm] incl,
275 340 380 (Classes 1 480 550 that have been produced by slitting from wider sheet.
and 2) Inch-Pound Units
410 The camber tolerance is ⁄ in. in any 8 ft.
1 4

Over 1.5 to 1500, 15 20 22 25 30 SI Units

inclusive The camber tolerance is 5.0 mm in any 2000 mm.
over 1500 25 30 32 35 38
1.5 and to 900, 15 20 22 25 30
thinner inclusive
over 900 25 30 32 35 33
to 1500, 13.1.1 Unless otherwise prohibited by the product
inclusive
over 1500 35 38 40 45 48
specification, retests are permitted under the following circum-
stances:
13.1.1.1 If any tension test specimen shows defective ma-
TABLE 13 Width Tolerances—Narrow Widths for Hot-Dip Metallic- chining or develops flaws, it must be discarded and another
Coated Sheet, Coil and Cut Lengths, Not Resquared specimen substituted.
NOTE 1—This table applies to widths produced by slitting from wider 13.1.1.2 If the percent elongation of any tension test speci-
sheet. men is less than that specified, and any part of the fracture is
more than 3⁄4 in. [20 mm] from the center of the gauge length
NOTE 2—The specified width range captions noted as follows are also
applied when sheet is specified to width tolerance all over, nothing under. of a 2-in. [50 mm] specimen, or is outside the middle half of
In such cases, the stated tolerances are doubled. the gauge length of an 8-in. [200 mm] specimen, as indicated
by scribe scratches marked on the specimen before testing, a
NOTE 3—Tolerances based upon practice found to be generally fol-
lowed by producers. retest is allowed.
13.1.1.3 If the test result of any tension test specimen fails
Inch-Pound Units
to meet the specification requirements and the failure is the
Specified Thickness, in. Tolerances Over and Under Specified Width, in.
result of improper adherence to tension test procedures, a retest
From 2 Over 6 Over 9
Over Through
through 6 through 9 through 12 is permitted.
0.014 0.068 0.008 0.016 0.032 13.1.1.4 If the test result of an original tension test specimen
0.068 0.083 0.012 0.016 0.032 fails to meet the specification requirements and the failure is
0.083 0.110 0.016 0.032 0.032 not related to the conditions described in 13.1.1.1, 13.1.1.2, and
0.110 0.250 0.032 0.032 0.032
SI Units 13.1.1.3, but the results are within 2 ksi [14 Mpa] of the
Specified Width, mm
Width Tolerance, Over and Under, mm
required yield strength, within 2 ksi [14 MPa] of the required
Over Through
50 100 0.3
tensile strength, or within 2 percentage points of the required
100 200 0.4 elongation, one retest shall be permitted to replace the failing
200 300 0.8 test.
13.1.2 The retest specimen shall be taken either adjacent to
the first failed specimen, or selected at random from the
opportunity to remove portions containing imperfections as in material to be certified to the specification.
the case with cut lengths. 13.1.3 If the results of a retest satisfy the specified tension
test requirements and all other requirements of the applicable
13. Retests and Disposition of Non-Conforming Material specification are satisfied, the material shall be accepted.
13.1 Retests: 13.2 Disposition of Non-Conforming Material:

7
 A924/A924M − 14
13.2.1 In those cases where the lot is found to be non- 16. Certification
conforming, and resampling of non-conforming material is not 16.1 When required by the purchase order, a certificate of
prohibited by the specification. resampling is permitted under compliance or a test report, or both, shall be furnished to the
the following circumstances and using the following practices: purchaser.
13.2.1.1 If the results of an original tension test or retest 16.1.1 The certificate of compliance shall include a certifi-
specimen fail to satisfy the specification requirements and the cation that the product has been manufactured and tested in
failed test results are not related to the conditions described in accordance with the requirements of the product specification,
13.1, the lot shall be quarantined and resampled for certifica- and that the test results conform to the requirements of that
tion of the non-conforming material to the specification re- specification.
quirements. 16.1.2 The test report shall show the heat analysis and the
13.2.1.2 Resampling for certification of the non-conforming results of all tests required by the product specification and the
material shall include the discarding of out of-specification order.
material and the resampling of the lot. The resampling shall be 16.1.3 These documents shall provide information neces-
sary to identify the product represented; for example, the
appropriate to the specific out-of-specification condition and
manufacturer’s name or brand, ASTM specification, coating
the processing history of the lot.
designation, grade (when required), ordered thickness, width,
13.2.1.3 A maximum of two resampling efforts shall he length (if cut length), and unit identification (heat number, coil
permitted. If, after conducting two resampling efforts, the number, etc.).
material does not satisfy the specification requirements, the lot 16.1.4 A signature is not required. However, the certifica-
shall be rejected. tion documents shall clearly identify the organization submit-
ting the information. Notwithstanding the absence of a
14. Inspection signature, the organization submitting the documents is respon-
14.1 The producer shall afford the purchaser’s inspector sible for the accuracy of the information.
reasonable access to facilities to ensure that the product is 16.2 The furnishing of a certificate of compliance or test
being produced in compliance with this specification. Unless report, or both, shall not restrict the right of the purchaser to
otherwise specified, all inspection and tests, except product sample and test the product furnished.
analysis, shall be made at the producer’s facilities prior to 17. Packaging and Package Marking
shipment. Such inspection or sampling shall be made concur-
rently with the producer’s regular inspection and test opera- 17.1 It is common practice to use the methods of packaging
tions unless it causes interference with normal operations or is as listed in the latest revision of Practices A700, but the
purchaser is permitted to specify other packaging methods.
otherwise specified.
17.2 As a minimum requirement, the product shall be
14.2 Responsibility for Inspection —Unless otherwise identified by having the manufacturer’s name or brand, ASTM
specified in the contract or purchase order, the producer is specification, coating designation, grade, size, unit weight,
responsible for the performance of all inspection requirements purchaser’s order number, and unit identification (that is, ticket
as specified herein. Except as otherwise specified in the number, coil number, etc.) legibly shown on a tag attached to
contract or order, the producer’s facilities, or any other each coil or shipping unit.
facilities suitable for the performance of the inspection
17.3 Most producers are able to ink stamp metallic-coated
requirements, shall be used. The purchaser reserves the right to
sheet with their logo and the pertinent ASTM specification
perform any of the inspections set forth in this specification to when ordered in either coil or cut lengths. Since many of the
ensure supplies and services conform to the prescribed require- metallic-coated products are stamped with a permanent ink
ments. (not water soluble), the purchaser shall be very specific when
placing an order as to the requirements on sheet marking.
15. Rejection and Rehearing
17.4 The purchase order shall include the specific loading
15.1 Unless otherwise specified, any rejection shall be instructions.
reported to the producer within a reasonable time after receipt
17.5 When specified in the contract or order, and for direct
of product by the purchaser. shipments to the U.S. Federal government, marking for ship-
15.2 Product that is reported to be unacceptable subsequent ment shall be in accordance with Fed. Std. No. 123 for civil
to the shipment to the purchaser’s plant, shall be set aside, agencies.
adequately protected, and correctly identified. The producer 18. Keywords
shall be notified as soon as possible to permit a timely
investigation. 18.1 aluminum-coated iron/steel; aluminum-zinc alloy-
coated steel, 55 %; coating; coatings—55 % aluminum-zinc;
15.3 Samples that are representative of the rejected product coatings—aluminum; coatings—hot-dip; coatings—metallic;
shall be made available to the producer. In the event that the coatings—terne metal; coatings—zinc-5 % aluminum;
producer is dissatisfied with the rejection, a rehearing shall be coatings—zinc (hot-dip); coatings—zinc-aluminum-
requested. magnesium; corrosion; hot-dip; metallic-coated; sheet; steel;

8
 A924/A924M − 14
steel products—hot-dip coatings; steel sheet—aluminum-
coated; steel sheet—terne coated; steel sheet—zinc-aluminum-
magnesium alloy-coated; steel sheet—zinc-coated (galva-
nized); zinc-aluminum-magnesium alloy-coated steel; zinc-
coated iron/steel

SUPPLEMENTARY REQUIREMENTS

THICKNESS TOLERANCES

The following supplementary requirements shall apply only when specified by the purchase order
or contract

APPENDIXES

TABLE S1.1 Thickness Tolerances for Hot-Dip Metallic-Coated Sheet—3⁄8-in. [10-mm] Minimum Edge Distance
NOTE 1—The coated sheet thickness includes the base metal and coating and is measured at any point across the width of the coated sheet not less
than 3⁄8 in. [10 mm] from a side edge.
NOTE 2—Micrometers used for measurement of thickness shall be constructed with anvils and spindles having minimum diameters of 0.188 in. [4.80
mm]. The tip of the anvil shall be flat or rounded with a minimum radius of curvature of 0.10 in. [2.55 mm] and the tip of the spindle shall be flat.
Micrometers with conical tips shall not be used for thickness measurements of sheet steels.
Inch-Pound Units
Specified Width, in. Specified Ordered Thickness, in.A,B
Over Through Through 0.023 Over 0.023 Over 0.043 Over 0.061 Over 0.075 Over 0.101 Over 0.187 Over 0.229
through 0.043 through 0.061 through 0.075 through 0.101 through 0.187 through 0.229 through 0.250
Thickness Tolerances, Over, in., No Tolerance UnderC
... 32 0.006 0.008 0.010 0.012 0.014 0.016 0.016 0.024
32 40 0.006 0.008 0.010 0.012 0.016 0.016 0.018 0.024
40 60 0.006 0.008 0.010 0.012 0.016 0.018 0.020 0.026
60 72 0.006 0.008 0.010 0.012 0.018 0.018 0.024 0.028
SI Units
Specified Width, mm Specified Ordered Thickness, mmB,D
Over Through Through 0.4 Over 0.4 Over 1.0 Over 1.5 Over 2.0 Over 2.5 Over 5.0 Over 6.0
through 1.0 through 1.5 through 2.0 through 2.5 through 5.0 through 6.0 through 6.3
Thickness Tolerances, Over, mm, No Tolerance UnderC
... 1500 0.16 0.20 0.26 0.30 0.40 0.46 0.56 0.60
1500 ... 0.16 0.20 0.26 0.30 0.46 0.46 0.60 0.64
A
Thickness is measured at any point across the width not less than 3⁄8 in. from a side edge.
B
The specified thickness range captions apply independently of whether the ordered thickness is stated as nominal or minimum.
C
The tolerances provided in the table are based on minimum thickness (tolerance over, no tolerance under). For nominal thickness, the tolerance is divided equally over
and under (tolerance over, tolerance under).
D
Thickness is measured at any point across the width not less than 10 mm from a side edge.

(Nonmandatory Information)

X1. PRODUCT INFORMATION

X1.1 Coating Thickness Measurements with Magnetic following the recommended practice for magnetic instruments
Gauges—A reasonable estimate of weight [mass] of described in Practice E376. This test may be used as a basis for
coating may be obtained by converting coating thickness acceptance, but rejection shall be governed by the weight
measurements made with magnetic gauges. An accuracy of [mass] of coating tests described in Section 8.
615 % in determining the thickness may be realized by

9
 A924/A924M − 14

X2. MILL-APPLIED CHEMICAL TREATMENTS ON METALLIC COATED SHEET STEELS

X2.1 The chemical treatments for metallic-coated coil de- self-healing capability. However, over long periods of time, the
scribed in this section of the appendix are specific to those that Cr+6 oxidizes completely to Cr+3. These materials are generally
require little reaction time, can be roll-applied (flood & not considered paintable without extreme removal techniques.
squeegee or chemcoater) and dried with simple heating capa- The passivation mechanism of Cr+3 is similar, but more
bility at the exit end of the metallic coating line. This is in difficult to achieve. Hence, the less effective Cr+3 coatings are
contrast to those that require several step immersion baths and applied at coating weights 3-5 times greater than the Cr+6
longer reaction times typically utilized on coil paint lines. The versions. Many of the Cr+3 based coatings are paintable
products are divided into three groups based on the following utilizing normal cleaning methods.
characteristics: (1) surface protection only, (2) formability X2.3.2 Chrome Bearing Organic Coatings—Generally ap-
enhancement, and (3) a combination of surface protection and plied from acrylic polymer solutions containing Cr+6 or Cr+3
formability enhancement. constituents, these coatings are applied in the 3-5 g/m2 coating
X2.2 Formability Enhancement weight range. Roll-application and drying are recommended
prior to coiling. Characteristics include the reduction or elimi-
X2.2.1 Dried-in-Place Phosphate Coatings—These tri- nation of storage and transit corrosion. While some of these
metal [Zn-Mn-Ni], tricationic microcrystalline phosphate crys- products are paintable within a prescribed timeframe, it is
tals are applied as a surface treatment within a 0.5–1.5g/m2 recommended to check with the supplier regarding durability
coating weight range. Application is generally performed from of post-painted product.
an aqueous solution utilizing a pair of rubber rolls. The coated
surface is dried using a simple IR or convection oven, heating X2.3.3 Chrome-Free Coatings—True chrome free coatings
the strip to a temperature high enough to drive off water. The can be manufactured from both organic and inorganic materials
phosphate coating is often oiled using simple mill oil in order that may be pigmented with calcium phosphates, titanium
to inhibit corrosion and moisture pickup by the phosphate silicon phosphates, etc. These are roll-applied from solution
crystals during transport and storage. This type of coating is and dried. While most of these coatings accept a post-paint, it
applied to aid in formability. Once formed, these products are is recommended to verify durability of particular systems with
cleaned, and rephosphated prior to painting. the supplier.

X2.2.2 Soap Lubricants—Alkaline-based soap lubricants X2.4 Formability Enhancement and Surface Protection
can be roll-applied from aqueous solution and dried by driving X2.4.1 Acrylic Coatings—Permanent and alkaline-
off water. Coating weights vary by application. These materials removable solid film acrylic coatings can be applied from
are utilized to enhance formability. Moisture uptake is a aqueous solutions at coating weights between 144–360 mg/in.
problem in humid environments that may lead to surface 2. Note that some of these coatings require a minimum peak
corrosion and short blanking during the forming operation. metal temperature of 125C for drying in order to drive off
Soaps are more commonly utilized over heavily pigmented water and inhibit moisture migration through the coating that
[rough] prepainted surfaces. can lead to corrosion of the strip. The low surface friction
characteristics of these coatings are excellent for formability
X2.3 Surface Protection enhancement, irrespective of strip surface finish. No oiling of
X2.3.1 Chrome Bearing Inorganic Passivation Coatings— the strip is required. Excellent storage and transit corrosion
These coatings are spray/squeegee or roll-applied from an protection can be expected. The permanent coatings are paint-
aqueous solution containing eitherCr+6 or Cr+3. The Cr+6 able unless formulated with silicon pigments or wax. The
containing coatings are true passivants utilized as a protection non-permanent coating is easily removed in a standard alkaline
against storage stain and transit corrosion and applied between cleaner, subsequent to which standard phosphating and paint-
1-3 gm/m2. Shortly after application, most of the Cr+6 oxidizes ing techniques can be utilized on the metallic coated strip. The
to Cr+3. The remaining Cr+6 allows for repassivation when the removable coatings provide excellent protection from dirt and
surface is minimally damaged [scratched], providing a unique soil in order to enhance phosphating and painting.

10
 A924/A924M − 14
TABLE X2.1 Surface Treatment Property and Characteristic Comparison
CHEMICAL TREATMENT Properties Chemical Characteristics
Formable Paintable Storage Transit Cr+6 Cr+3 Non- Non- Crystalline Acrylic Soap
Stain Corrosion Chrome Chrome Polymer Base
Protection Protection Solution Pigments Base
Zinc Phosphate and Oil U U U U U U
Soap Lubricants U After U U U U
removal
Inorganic [Cr-bearing] U Check U U U U
with
supplier
Organic [Cr bearing] U Check U U U U U
with
supplier
Organic [Cr Free] U Check U U U U U
with
supplier
Inorganic [Cr Free] U Check U U U U U
with
supplier
Acrylic Solid Film [Permanent] U When U U U
without
Si or wax
Acrylic Solid Film [Removable] U U U U U
Inorganic [Cr-bearing] U Check U U U
with
supplier
Note also that other properties can either be inherent to or incorporated into the chemical treatments listed above. As many properties are formula driven, all cannot
be incorporated here. Check with the supplier for product tailoring when properties such as resistivity, weldability, anti-fingerprinting, microbial resistance, tinting or
transparency are specified or required.

X3. GUIDE TO CONVERSION BETWEEN COATING WEIGHT [MASS] AND THICKNESS

NOTE X3.1—The values in the tables below are based on the assumed TABLE X3.3 A653/A653M Zinc-Coated (Galvanized/Galvannealed)
three significant figure relationships shown under the title of each table. Sheet, and A1063/A1063M Twin Roll-Cast Zinc-Coated
This can result in some very small conversion anomalies that are (Galvanized)
considered to be insignificant given these tables are for information (Assume 1.00 oz/ft2 = 305 g/m2 = 1.68 mils)
purposes only. Coating Weight [Mass] Coating Thickness
NOTE X3.2—The values apply to total-both-sides measurements, and to oz/ft2 [g/m2] mil µm
single-side measurements in the case of differential coatings. 1.00 305 1.68 42.7
NOTE X3.3—The values should NOT be used to calculate residual 0.00328 1.00 0.00551 0.140
metallic coating thickness after corrosion has occurred in service. 0.595 181 1.00 25.4
0.0234 7.14 0.0394 1.00

TABLE X3.1 A463/A463M Aluminum-Coated Type 1 Sheet

(Assume 1.00 oz/ft 2 = 305 g/m2 = 3.98 mils) TABLE X3.4 A792/A792M 55% Aluminum-Zinc Alloy-Coated Sheet
(Assume 1.00 oz/ft2 = 305 g/m2 = 3.20 mils)
Coating Weight [Mass] Coating Thickness
oz/ft2 [g/m2] mil µm Coating Weight [Mass] Coating Thickness
1.00 305 3.98 101 oz/ft2 [g/m2] mil µm
0.00328 1.00 0.0131 0.331 1.00 305 3.20 81.3
0.251 76.6 1.00 25.4 0.00328 1.00 0.0105 0.267
0.00989 3.02 0.0394 1.00 0.313 95.4 1.00 25.4
0.0123 3.75 0.0394 1.00

TABLE X3.2 A463/A463M Aluminum-Coated Type 2 Sheet TABLE X3.5 A875/A875M Zinc-5% Aluminum Alloy-Coated Sheet
(Assume 1.00 oz/ft 2 = 305 g/m2 = 3.74 mils) (Assume 1.00 oz/ft2 = 305 g/m2 = 1.75 mils)
Coating Weight [Mass] Coating Thickness Coating Weight [Mass] Coating Thickness
oz/ft2 [g/m2] mil µm oz/ft2 [g/m2] mil µm
1.00 305 3.74 95.0 1.00 305 1.75 44.6
0.00328 1.00 0.0123 0.312 0.00328 1.00 0.00574 0.146
0.267 81.4 1.00 25.4 0.570 174 1.00 25.4
0.0105 3.20 0.0394 1.00 0.0224 6.83 0.0394 1.00

11
 A924/A924M − 14
TABLE X3.6 A1046/A1046M Zinc-Aluminum-Magnesium Alloy-
Coated Sheet (5-9% Al)
(Assume 1.00 oz/ft2 = 305 g/m2 = 2.00 mils)
Coating Weight [Mass] Coating Thickness
oz/ft2 [g/m2] mil µm
1.00 305 2.00 50.8
0.00328 1.00 0.00656 0.167
0.500 153 1.00 25.4
0.0197 6.01 0.0394 1.00

TABLE X3.7 A1046/A1046M Zinc-Aluminum-Magnesium Alloy-

Coated Sheet (9-13% Al)
(Assume 1.00 oz/ft2 = 305 g/m2 = 2.10 mils)
Coating Weight [Mass] Coating Thickness
oz/ft2 [g/m2] mil µm
1.00 305 2.10 53.3
0.00328 1.00 0.00689 0.175
0.476 145 1.00 25.4
0.0187 5.70 0.0394 1.00

SUMMARY OF CHANGES

Committee A05 has identified the location of selected changes to this standard since the last issue
(A924/A924M - 13) that may impact the use of this standard. (October 1, 2014)

(1) Added heavy thickness tolerances to Table 2 and Table (2) Increased the thickness covered by Table 13 to 0.250 in.
S1.1.

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.

This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or [email protected] (e-mail); or through the ASTM website
(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222
Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http://www.copyright.com/

12