LP 5907

Product Order Technical Tools & Support & Reference
Folder Now Documents Software Community Design
LP5907
SNVS798N – APRIL 2012 – REVISED APRIL 2018
LP5907 250-mA, Ultra-Low-Noise, Low-IQ LDO

1 Features 3 Description
•
1 Input Voltage Range: 2.2 V to 5.5 V The LP5907 is a low-noise LDO that can supply up to
250 mA output current. Designed to meet the
• Output Voltage Range: 1.2 V to 4.5 V requirements of RF and analog circuits, the LP5907
• Stable With 1-µF Ceramic Input and Output device provides low noise, high PSRR, low quiescent
Capacitors current, and low line or load transient response
• No Noise Bypass Capacitor Required figures. Using new innovative design techniques, the
LP5907 offers class-leading noise performance
• Remote Output Capacitor Placement
without a noise bypass capacitor and the ability for
• Thermal-Overload and Short-Circuit Protection remote output capacitor placement.
• –40°C to 125°C Operating Junction Temperature The device is designed to work with a 1-µF input and
• Low Output Voltage Noise: < 6.5 µVRMS a 1-µF output ceramic capacitor (no separate noise
• PSRR: 82 dB at 1 kHz bypass capacitor is required).
• Output Voltage Tolerance: ±2% This device is available with fixed output voltages
• Very Low IQ (Enabled): 12 µA from 1.2 V to 4.5 V in 25-mV steps. Contact Texas
Instruments Sales for specific voltage option needs.
• Low Dropout: 120 mV (typical)
• Create a Custom Design Using the LP5907 With Device Information(1)
the WEBENCH® Power Designer PART NUMBER PACKAGE BODY SIZE
DSBGA (4) 0.675 mm × 0.675 mm (MAX)
2 Applications LP5907 SOT-23 (5) 2.90 mm × 1.60 mm (NOM)
• Mobile Phones, Tablets X2SON (4) 1.00 mm × 1.00 mm (NOM)
• Digital Cameras and Audio Devices (1) For all available packages, see the orderable addendum at
• Portable and Battery-Powered Equipment the end of the data sheet.
• Portable Medical Equipment space
• Smart Meters and Field Transmitters space
• RF, PLL, VCO, and Clock Power Supplies space
• IP Cameras
• Drones
Simplified Schematic
INPUT IN OUT OUTPUT
1 PF 1 PF
LP5907
ENABLE EN
GND
GND
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LP5907
SNVS798N – APRIL 2012 – REVISED APRIL 2018 www.ti.com
Table of Contents
1 Features .................................................................. 1 7.4 Device Functional Modes........................................ 13
2 Applications ........................................................... 1 8 Application and Implementation ........................ 14
3 Description ............................................................. 1 8.1 Application Information............................................ 14
4 Revision History..................................................... 2 8.2 Typical Application .................................................. 14
5 Pin Configuration and Functions ......................... 4 9 Power Supply Recommendations...................... 17
6 Specifications......................................................... 5 10 Layout................................................................... 18
6.1 Absolute Maximum Ratings ...................................... 5 10.1 Layout Guidelines ................................................. 18
6.2 ESD Ratings.............................................................. 5 10.2 Layout Examples................................................... 18
6.3 Recommended Operating Conditions....................... 5 11 Device and Documentation Support ................. 20
6.4 Thermal Information .................................................. 6 11.1 Documentation Support ........................................ 20
6.5 Electrical Characteristics........................................... 6 11.2 Receiving Notification of Documentation Updates 20
6.6 Output and Input Capacitors ..................................... 7 11.3 Community Resources.......................................... 20
6.7 Typical Characteristics .............................................. 8 11.4 Trademarks ........................................................... 20
7 Detailed Description ............................................ 12 11.5 Electrostatic Discharge Caution ............................ 20
7.1 Overview ................................................................. 12 11.6 Glossary ................................................................ 20
7.2 Functional Block Diagram ....................................... 12 12 Mechanical, Packaging, and Orderable
7.3 Feature Description................................................. 12 Information ........................................................... 21
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision M (January 2018) to Revision N Page
• Added Overshoot on start-up with EN row to Electrical Characteristics table ...................................................................... 7
Changes from Revision L (August 2016) to Revision M Page
• Added links for WEBENCH ................................................................................................................................................... 1

• Added information about YKM package option ..................................................................................................................... 1
• Added minor editorial changes .............................................................................................................................................. 1
Changes from Revision K (May 2016) to Revision L Page
• Changed title of data sheet and updated list of Applications and wording of 1st sentence in Description ............................ 1
• Changed "10 µVRMS" to "6.5 µVRMS" ....................................................................................................................................... 1
Changes from Revision J (March 2016) to Revision K Page
• Changed "Linear Regulator" to "LDO" in title and first sentence of Description .................................................................... 1
Changes from Revision I (August 2015) to Revision J Page
• Changed VOUT min and max values and VEN min value in Abs Max table and VEN row of ROC table to correct format
errors; replace text of footnote 2 of Abs Max table ............................................................................................................... 5
Changes from Revision H (November 2014) to Revision I Page
• Added icon for reference design to Top Navs and "ΔVOUT vs Temperature" graph to Typical Characteristics ..................... 1
• Changed Storage Temperature to Abs Max table; replace Handling Ratings with ESD Ratings ......................................... 5
• Deleted "VOUT ≥ 1.8 V" from first row of ΔVout spec ............................................................................................................. 6
2 Submit Documentation Feedback Copyright © 2012–2018, Texas Instruments Incorporated
Product Folder Links: LP5907

LP5907
www.ti.com SNVS798N – APRIL 2012 – REVISED APRIL 2018
• Added "SOT-23, X2SON packages" to second row of ΔVout spec ...................................................................................... 6
Changes from Revision G (October 2013) to Revision H Page
• Added Device Information and Handling Rating tables, Feature Description, Device Functional Modes, Application
and Implementation, Power Supply Recommendations, Layout, Device and Documentation Support, and
Mechanical, Packaging, and Orderable Information sections; moved some curves to Application Curves section ............. 1
Copyright © 2012–2018, Texas Instruments Incorporated Submit Documentation Feedback 3

LP5907
5 Pin Configuration and Functions
YKE and YKM Packages

4-Pin DSBGA
IN OUT OUT IN
A1 A2 A2 A1
B1 B2 B2 B1
EN GND GND EN
TOP VIEW BOTTOM VIEW
Pin Functions: DSBGA

PIN
DSBGA I/O DESCRIPTION
NAME
NUMBER
A1 IN I Input voltage supply. Connect a 1-µF capacitor at this input.
Regulated output voltage. Connect a minimum 1-µF low-ESR capacitor to this pin. Connect
A2 OUT O this output to the load circuit. An internal 230-Ω (typical) pulldown resistor prevents a charge
remaining on VOUT when the regulator is in the shutdown mode (VEN low).
Enable input. A low voltage (< VIL) on this pin turns the regulator off and discharges the
output pin to GND through an internal 230-Ω pulldown resistor. A high voltage (> VIH) on this
B1 EN I
pin enables the regulator output. This pin has an internal 1-MΩ pulldown resistor to hold the
regulator off by default.
B2 GND — Common ground
DQN Package DBV Package

4-Pin X2SON 5-Pin SOT-23
Bottom View Top View
OUT GND
1 2 IN 1 5 OUT
GND 2
5
EN 3 4 N/C
4 3
IN EN
Pin Functions: X2SON, SOT-23

PIN
X2SON SOT-23 I/O DESCRIPTION
NAME
NUMBER NUMBER
IN 4 1 I Input voltage supply. Connect a 1-µF capacitor at this input.
Regulated output voltage. Connect a minimum 1-µF low-ESR capacitor to this
pin. Connect this output to the load circuit. An internal 230-Ω (typical) pulldown
OUT 1 5 O
resistor prevents a charge remaining on VOUT when the regulator is in the
shutdown mode (VEN low).
Enable input. A low voltage (< VIL) on this pin turns the regulator off and
discharges the output pin to GND through an internal 230-Ω pulldown resistor. A
EN 3 3 I
high voltage (> VIH) on this pin enables the regulator output. This pin has an
internal 1-MΩ pulldown resistor to hold the regulator off by default.
GND 2 2 — Common ground
N/C — 4 — No internal electrical connection.
Thermal pad for X2SON package, connect to GND or leave floating. Do not
Thermal Pad 5 — —
connect to any potential other than GND.

LP5907
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) (2)
MIN MAX UNIT
VIN Input voltage –0.3 6
VOUT Output voltage –0.3 See (3) V
VEN Enable input voltage –0.3 6
Continuous power dissipation (4) Internally Limited W
TJMAX Junction temperature 150 °C
Tstg Storage temperature –65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages are with respect to the GND pin.
(3) Abs Max VOUT is the lessor of VIN + 0.3 V, or 6 V.
(4) Internal thermal shutdown circuitry protects the device from permanent damage.
6.2 ESD Ratings

VALUE UNIT
(1)
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 ±2000
V(ESD) Electrostatic discharge V
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2) ±1000
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted) (1) (2)
MIN MAX UNIT
VIN Input supply voltage 2.2 5.5
V
VEN Enable input voltage 0 5.5
IOUT Output current 0 250 mA
TJ Junction temperature –40 125 °C
(3)
TA Ambient temperature –40 85 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages are with respect to the GND pin.
(3) In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may
have to be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP =
125°C), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the
part/package in the application (RθJA), as given by the following equation: TA-MAX = TJ-MAX-OP – (RθJA × PD-MAX). See Application and
Implementation.

LP5907
6.4 Thermal Information

LP5907
(1) DBV DQN YKE YKM
THERMAL METRIC UNIT
(SOT-23) (X2SON) (DSBGA) (DSBGA)
5 PINS 4 PINS 4 PINS 4 PINS
RθJA Junction-to-ambient thermal resistance 193.4 216.1 206.1 194.1 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 102.1 161.7 1.5 3.0 °C/W
RθJB Junction-to-board thermal resistance 45.8 162.1 37.0 62.7 °C/W
ψJT Junction-to-top characterization parameter 8.4 5.1 15.0 1.1 °C/W
ψJB Junction-to-board characterization parameter 45.3 161.7 36.8 62.7 °C/W
RθJC(bot) Junction-to-case (bottom) thermal resistance n/a 123.0 n/a n/a °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
6.5 Electrical Characteristics

VIN = VOUT(NOM) + 1 V, VEN = 1.2 V, IOUT = 1 mA, CIN = 1 µF, COUT = 1 µF (unless otherwise noted) (1) (2) (3)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
VIN Input voltage TA = 25°C 2.2 5.5 V
VIN = (VOUT(NOM) + 1 V) to 5.5 V,
–2 2
IOUT = 1 mA to 250 mA
Output voltage tolerance VIN = (VOUT(NOM) + 1 V) to 5.5 V, %VOUT
IOUT = 1 mA to 250 mA –3 3
ΔVOUT (VOUT < 1.8 V, SOT-23, X2SON packages)
VIN = (VOUT(NOM) + 1 V) to 5.5 V,
Line regulation 0.02 %/V
IOUT = 1 mA
Load regulation IOUT = 1 mA to 250 mA 0.001 %/mA
Load current See (4) 0 250 mA
ILOAD
Maximum output current 250
VEN = 1.2 V, IOUT = 0 mA 12 25
IQ Quiescent current (5) VEN = 1.2 V, IOUT = 250 mA 250 425 µA
VEN = 0.3 V (disabled) 0.2 1
IG Ground current (6) VEN = 1.2 V, IOUT = 0 mA 14 µA
IOUT = 100 mA 50
VDO Dropout voltage (7) IOUT = 250 mA (DSBGA package) 120 200 mV
IOUT = 250 mA (SOT-23, X2SON packages) 250
ISC Short-circuit current limit TA = 25°C (8) 250 500 mA
(1) All voltages are with respect to the device GND terminal, unless otherwise stated.
(2) Minimum and maximum limits are ensured through test, design, or statistical correlation over the junction temperature (TJ) range of
–40°C to 125°C, unless otherwise stated. Typical values represent the most likely parametric norm at TA = 25°C, and are provided for
reference purposes only.
(3) In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may
have to be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP =
125°C), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the
part/package in the application RθJA), as given by the following equation: TA-MAX = TJ-MAX-OP – (RθJA × PD-MAX). See Application and
Implementation.
(4) The device maintains a stable, regulated output voltage without a load current.
(5) Quiescent current is defined here as the difference in current between the input voltage source and the load at VOUT.
(6) Ground current is defined here as the total current flowing to ground as a result of all input voltages applied to the device.
(7) Dropout voltage is the voltage difference between the input and the output at which the output voltage drops to 100 mV below its
nominal value.
(8) Short-circuit current (ISC) for the LP5907 is equivalent to current limit. To minimize thermal effects during testing, ISC is measured with
VOUT pulled to 100 mV below its nominal voltage.

LP5907
Electrical Characteristics (continued)

VIN = VOUT(NOM) + 1 V, VEN = 1.2 V, IOUT = 1 mA, CIN = 1 µF, COUT = 1 µF (unless otherwise noted)(1)(2)(3)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
f = 100 Hz, IOUT = 20 mA 90
f = 1 kHz, IOUT = 20 mA 82
PSRR Power-supply rejection ratio (9) dB
f = 10 kHz, IOUT = 20 mA 65
f = 100 kHz, IOUT = 20 mA 60
IOUT = 1 mA 10
eN Output noise voltage (9) BW = 10 Hz to 100 kHz µVRMS
IOUT = 250 mA 6.5
Output automatic discharge
RAD VEN < VIL (output disabled) 230 Ω
pulldown resistance
Thermal shutdown TJ rising 160
TSD °C
Thermal hysteresis TJ falling from shutdown 15
LOGIC INPUT THRESHOLDS
VIN = 2.2 V to 5.5 V,
VIL Low input threshold 0.4 V
VEN falling until the output is disabled
VIN = 2.2 V to 5.5 V
VIH High input threshold 1.2 V
VEN rising until the output is enabled
VEN = 5.5 V and VIN = 5.5 V 5.5
IEN Input current at EN pin (10) µA
VEN = 0 V and VIN = 5.5 V 0.001
TRANSIENT CHARACTERISTICS
VIN = (VOUT(NOM) + 1 V) to
–1
(9)
(VOUT(NOM) + 1.6 V) in 30 µs
Line transient
VIN = (VOUT(NOM) + 1.6 V) to
1 mV
(VOUT(NOM) + 1.6 V) in 30 µs
IOUT = 1 mA to 250 mA in 10 µs –40
Load transient (9)
ΔVOUT IOUT = 250 mA to 1 mA in 10 µs 40
(9)
Overshoot on start-up Stated as a percentage of VOUT(NOM) 5%
Stated as a percentage of VOUT(NOM), VIN =
VOUT + 1 V to 5.5 V, 0.7 µF < COUT < 10 µF,
Overshoot on start-up with EN (9) 1%
0 mA < IOUT < 250 mA, EN rising until the
output is enabled
From VEN > VIH to VOUT = 95% of VOUT(NOM),
tON Turnon time 80 150 µs
TA = 25°C
(9) This specification is verified by design.

(10) There is a 1-MΩ resistor between EN and ground on the device.
6.6 Output and Input Capacitors

over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN (1) TYP MAX UNIT
(2)
CIN Input capacitance 0.7 1 µF
Capacitance for stability
COUT Output capacitance (2) 0.7 1 10 µF
ESR Output/Input capacitance (2) 5 500 mΩ
(1) The minimum capacitance should be greater than 0.5 µF over the full range of operating conditions. The capacitor tolerance should be
30% or better over the full temperature range. The full range of operating conditions for the capacitor in the application must be
considered during device selection to ensure this minimum capacitance specification is met. X7R capacitors are recommended however
capacitor types X5R, Y5V and Z5U may be used with consideration of the application and conditions.
(2) This specification is verified by design.

LP5907
6.7 Typical Characteristics

VIN = 3.7 V, VOUT = 2.8 V, IOUT = 1 mA, CIN = 1 µF, COUT = 1 µF, TA = 25°C (unless otherwise noted)
16 1
14
0.9
12
10
0.8
IQ( A)
VEN (V)
8
6 0.7
4
0.6
2
VIH Rising
0 VIL Falling
0.5
2.3 2.8 3.3 3.8 4.3 4.8 5.3 5.8 2 2.5 3 3.5 4 4.5 5 5.5 6
VIN(V) VIN (V) D001
SVA-30180569
Figure 1. Quiescent Current vs Input Voltage Figure 2. VEN Thresholds vs VIN

1.4 5
4.5
1.2
4
1 3.5
3
VOUT (V)
VOUT (V)
0.8
2.5
0.6
2
0.4 1.5
1
0.2 RLOAD = 1.2 k: RLOAD = 4.5 k:
0.5
RLOAD = 4.8 : RLOAD = 18 :
0 0
0 0.5 1 1.5 2 2.5 0 1 2 3 4 5 6
VIN (V) D002
VIN (V) D003
VOUT = 1.2 V, VEN = VIN VOUT = 4.5 V, VEN = VIN
Figure 3. VOUT vs VIN Figure 4. VOUT vs VIN

350 2.900
VIN= 3.6V
300 2.875
GROUND CURRENT ( A)
250 2.850
2.825
VOUT(V)
200
2.800
150
2.775
100
2.750
VIN = 3.0V -40°C
50 VIN = 3.8V 2.725 90°C
VIN = 4.2V 25°C
VIN = 5.5V
0 2.700
0 50 100 150 200 250 300 0 50 100 150 200 250
IOUT(mA) LOAD (mA)
SVA-30180571 SVA-30180567
Figure 5. Ground Current vs Output Current Figure 6. Load Regulation

LP5907
Typical Characteristics (continued)

0.2 2.900
2.875 Load = 10 mA
0.1
2.850
0 2.825
VOUT(V)
'VOUT (%)
2.800
-0.1
2.775
-0.2
2.750
-40°C
2.725 90°C
-0.3 25°C
2.700
-0.4 3.0 3.5 4.0 4.5 5.0 5.5
-50 -25 0 25 50 75 100 125
Junction Temperature (qC) D010 VIN(V) SVA-30180568
Figure 7. ΔVOUT vs Temperature Figure 8. Line Regulation
2V/DIV
VOUT 10 mV/
VOUT
(AC Coupled) DIV
2V/DIV
VIN = VEN VIN 1V/DIV
IIN 1A/DIV
2 ms/DIV 10 s/DIV
SVA-30180509 SVA-30180510
VIN = 3.2 V ↔ 4.2 V, load = 1 mA
Figure 9. Inrush Current Figure 10. Line Transient
VOUT 10 mV/ VOUT 100 mV/DIV

(AC Coupled) DIV
VIN 1V/DIV
LOAD 200 mA/DIV
10 s/DIV 100 s/DIV
SVA-30180511 SVA-30180512
VIN = 3.2 V ↔ 4.2 V, load = 250 mA Load = 0 mA ↔ 250 mA, –40°C
Figure 11. Line Transient Figure 12. Load Transient

LP5907

VOUT 100 mV/DIV VOUT 100 mV/DIV
LOAD 200 mA/DIV

LOAD 200 mA/DIV
100 s/DIV
100 s/DIV
SVA-30180513 SVA-30180514
Load = 0 mA ↔ 250 mA, 90°C Load = 0 mA ↔ 250 mA, 25°C
Figure 13. Load Transient Figure 14. Load Transient
1V/DIV 1V/DIV
VOUT VOUT
1V/DIV
1V/DIV
EN
EN
20 s/DIV
20 s/DIV
SVA-30180516
SVA-30180515 Load = 250 mA
Load = 0 mA
Figure 15. Start-Up Figure 16. Start-Up

140
120
DROPOUT VOLTAGE (mV)
100
80
60
40
Dropout Voltage
20
0
0 50 100 150 200 250
LOAD CURRENT (mA)
SVA-30180573
Figure 17. Noise Density Test Figure 18. Dropout Voltage vs Load Current

LP5907

0 0
250 mA
200 mA
-20 150 mA -20
100 mA
50 mA
-40 20 mA -40
PSRR (dB)
PSRR (dB)
-60 -60
-80 -80 250 mA

200 mA
150 mA
-100 -100 100 mA
50 mA
20 mA
-120 -120
0.1 1 10 100 0.01 0.1 1 10 100 1000 10000
FREQUENCY (kHz) D004
FREQUENCY (kHz) D005
Figure 19. PSRR Loads Averaged 100 Hz to 100 kHz Figure 20. PSRR Loads Averaged 10 Hz to 10 MHz

LP5907
7 Detailed Description
7.1 Overview
Designed to meet the needs of sensitive RF and analog circuits, the LP5907 provides low noise, high PSRR, low
quiescent current, as well as low line and load transient response figures. Using new innovative design
techniques, the LP5907 offers class leading noise performance without the need for a separate noise filter
capacitor.
The LP5907 is designed to perform with a single 1-µF input capacitor and a single 1-µF ceramic output
capacitor. With a reasonable PCB layout, the single 1-µF ceramic output capacitor can be placed up to 10 cm
away from the LP5907 device.
7.2 Functional Block Diagram
IN OUT
EN POR
EN
+
RF
CF
+
VBG
RAD
1.20V
EN
EN + EN
1M
VIH GND
7.3 Feature Description

7.3.1 Enable (EN)
The LP5907 EN pin is internally held low by a 1-MΩ resistor to GND. The EN pin voltage must be higher than the
VIH threshold to ensure that the device is fully enabled under all operating conditions. The EN pin voltage must
be lower than the VIL threshold to ensure that the device is fully disabled and the automatic output discharge is
activated.
7.3.2 Low Output Noise

Any internal noise at the LP5907 reference voltage is reduced by a first order low-pass RC filter before it is
passed to the output buffer stage. The low-pass RC filter has a –3 dB cut-off frequency of approximately 0.1 Hz.

LP5907
Feature Description (continued)

7.3.3 Output Automatic Discharge
The LP5907 output employs an internal 230-Ω (typical) pulldown resistance to discharge the output when the EN
pin is low, and the device is disabled.
7.3.4 Remote Output Capacitor Placement

The LP5907 requires at least a 1-µF capacitor at the OUT pin, but there are no strict requirements about the
location of the capacitor in regards the OUT pin. In practical designs, the output capacitor may be located up to
10 cm away from the LDO.
7.3.5 Thermal Overload Protection (TSD)

Thermal shutdown disables the output when the junction temperature rises to approximately 160°C which allows
the device to cool. When the junction temperature cools to approximately 145°C, the output circuitry enables.
Based on power dissipation, thermal resistance, and ambient temperature, the thermal protection circuit may
cycle on and off. This thermal cycling limits the dissipation of the regulator and protects it from damage as a
result of overheating.
The thermal shutdown circuitry of the LP5907 has been designed to protect against temporary thermal overload
conditions. The TSD circuitry was not intended to replace proper heat-sinking. Continuously running the LP5907
device into thermal shutdown may degrade device reliability.
7.4 Device Functional Modes

7.4.1 Enable (EN)
The LP5907 Enable (EN) pin is internally held low by a 1-MΩ resistor to GND. The EN pin voltage must be
higher than the VIH threshold to ensure that the device is fully enabled under all operating conditions.
When the EN pin is pulled low, and the output is disabled, the output automatic discharge circuitry is activated.
Any charge on the OUT pin is discharged to GND through the internal 230-Ω (typical) pulldown resistance.
7.4.2 Minimum Operating Input Voltage (VIN)

The LP5907 does not include any dedicated UVLO circuitry. The LP5907 internal circuitry is not fully functional
until VIN is at least 2.2 V. The output voltage is not regulated until VIN has reached at least the greater of 2.2 V or
(VOUT + VDO).

LP5907
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information

The LP5907 is designed to meet the requirements of RF and analog circuits, by providing low noise, high PSRR,
low quiescent current, and low line or load transient response figures. The device offers excellent noise
performance without the need for a noise bypass capacitor and is stable with input and output capacitors with a
value of 1 µF. The LP5907 delivers this performance in industry standard packages such as DSBGA, X2SON,
and SOT-23 which, for this device, are specified with an operating junction temperature (TJ) of –40°C to 125°C.
8.2 Typical Application

Figure 21 shows the typical application circuit for the LP5907. Input and output capacitances may need to be
increased above the 1 µF minimum for some applications.
INPUT IN OUT OUTPUT
1 PF 1 PF
LP5907
ENABLE EN
GND
GND
Figure 21. LP5907 Typical Application
8.2.1 Design Requirements
DESIGN PARAMETER EXAMPLE VALUE

Input voltage range 2.2 V to 5.5 V
Output voltage 1.8 V
Output current 200 mA
Output capacitor range 0.7 µF to 10 µF
Input/Output capacitor ESR range 5 to 500 mΩ

LP5907
8.2.2 Detailed Design Procedure
8.2.2.1 Custom Design With WEBENCH® Tools

Click here to create a custom design using the LP5907 device with the WEBENCH® Power Designer.
1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements.
2. Optimize the design for key parameters such as efficiency, footprint, and cost using the optimizer dial.
3. Compare the generated design with other possible solutions from Texas Instruments.
The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time
pricing and component availability.
In most cases, these actions are available:
• Run electrical simulations to see important waveforms and circuit performance
• Run thermal simulations to understand board thermal performance
• Export customized schematic and layout into popular CAD formats
• Print PDF reports for the design, and share the design with colleagues
Get more information about WEBENCH tools at www.ti.com/WEBENCH.
8.2.2.2 Power Dissipation and Device Operation

The permissible power dissipation for any package is a measure of the capability of the device to pass heat from
the power source, the junctions of the IC, to the ultimate heat sink, the ambient environment. Thus, the power
dissipation is dependent on the ambient temperature and the thermal resistance across the various interfaces
between the die junction and ambient air.
The maximum allowable power dissipation for the device in a given package can be calculated using Equation 1:
PD-MAX = ((TJ-MAX – TA) / RθJA) (1)
The actual power being dissipated in the device can be represented by Equation 2:
PD = (VIN – VOUT) × IOUT (2)
These two equations establish the relationship between the maximum power dissipation allowed due to thermal
consideration, the voltage drop across the device, and the continuous current capability of the device. These two
equations should be used to determine the optimum operating conditions for the device in the application.
In applications where lower power dissipation (PD) and/or excellent package thermal resistance (RθJA) is present,
the maximum ambient temperature (TA-MAX) may be increased.
In applications where high power dissipation and/or poor package thermal resistance is present, the maximum
ambient temperature (TA-MAX) may have to be derated. TA-MAX is dependent on the maximum operating junction
temperature (TJ-MAX-OP = 125°C), the maximum allowable power dissipation in the device package in the
application (PD-MAX), and the junction-to ambient thermal resistance of the part/package in the application (RθJA),
as given by Equation 3:
TA-MAX = (TJ-MAX-OP – (RθJA × PD-MAX)) (3)
Alternately, if TA-MAX can not be derated, the PD value must be reduced. This can be accomplished by reducing
VIN in the VIN–VOUT term as long as the minimum VIN is met, or by reducing the IOUT term, or by some
combination of the two.
8.2.2.3 External Capacitors

Like most low-dropout regulators, the LP5907 requires external capacitors for regulator stability. The device is
specifically designed for portable applications requiring minimum board space and smallest components. These
capacitors must be correctly selected for good performance.
8.2.2.4 Input Capacitor

An input capacitor is required for stability. The input capacitor should be at least equal to, or greater than, the
output capacitor for good load transient performance. At least a 1 µF capacitor has to be connected between the
LP5907 input pin and ground for stable operation over full load current range. Basically, it is ok to have more
output capacitance than input, as long as the input is at least 1 µF.

LP5907
The input capacitor must be located a distance of not more than 1 cm from the input pin and returned to a clean
analog ground. Any good quality ceramic, tantalum, or film capacitor may be used at the input.
NOTE
To ensure stable operation it is essential that good PCB practices are employed to
minimize ground impedance and keep input inductance low. If these conditions cannot be
met, or if long leads are to be used to connect the battery or other power source to the
LP5907, TI recommends increasing the input capacitor to at least 10 µF. Also, tantalum
capacitors can suffer catastrophic failures due to surge current when connected to a low-
impedance source of power (like a battery or a very large capacitor). If a tantalum
capacitor is used at the input, it should be verified by the manufacturer to have a surge
current rating sufficient for the application. The initial tolerance, applied voltage de-rating,
and temperature coefficient must all be considered when selecting the input capacitor to
ensure the actual capacitance is never less than 0.7 µF over the entire operating range.
8.2.2.5 Output Capacitor

The LP5907 is designed specifically to work with a very small ceramic output capacitor, typically 1 µF. A ceramic
capacitor (dielectric types X5R or X7R) in the 1 µF to 10 µF range, and with ESR between 5 mΩ to 500 mΩ, is
suitable in the LP5907 application circuit. For this device the output capacitor should be connected between the
OUT pin and a good connection back to the GND pin.
It may also be possible to use tantalum or film capacitors at the device output, VOUT, but these are not as
attractive for reasons of size and cost (see Capacitor Characteristics).
The output capacitor must meet the requirement for the minimum value of capacitance and have an ESR value
that is within the range 5 mΩ to 500 mΩ for stability. Like the input capacitor, the initial tolerance, applied voltage
de-rating, and temperature coefficient must all be considered when selecting the input capacitor to ensure the
actual capacitance is never less than 0.7 µF over the entire operating range.
8.2.2.6 Capacitor Characteristics

The LP5907 is designed to work with ceramic capacitors on the input and output to take advantage of the
benefits they offer. For capacitance values in the range of 1 µF to 10 µF, ceramic capacitors are the smallest,
least expensive and have the lowest ESR values, thus making them best for eliminating high frequency noise.
The ESR of a typical 1 µF ceramic capacitor is in the range of 20 mΩ to 40 mΩ, which easily meets the ESR
requirement for stability for the LP5907.
A better choice for temperature coefficient in a ceramic capacitor is X7R. This type of capacitor is the most stable
and holds the capacitance within ±15% over the temperature range. Tantalum capacitors are less desirable than
ceramic for use as output capacitors because they are more expensive when comparing equivalent capacitance
and voltage ratings in the 1 µF to 10 µF range.
Another important consideration is that tantalum capacitors have higher ESR values than equivalent size
ceramics. This means that while it may be possible to find a tantalum capacitor with an ESR value within the
stable range, it would have to be larger in capacitance (which means bigger and more costly) than a ceramic
capacitor with the same ESR value. It should also be noted that the ESR of a typical tantalum increases about
2:1 as the temperature goes from 25°C down to –40°C, so some guard band must be allowed.
8.2.2.7 Remote Capacitor Operation

The LP5907 requires at least a 1-µF capacitor at the OUT pin, but there is no strict requirements about the
location of the capacitor in regards to the pin. In practical designs the output capacitor may be located up to 10
cm away from the LDO. This means that there is no need to have a special capacitor close to the output pin if
there is already respective capacitors in the system (like a capacitor at the input of supplied part). The remote
capacitor feature helps user to minimize the number of capacitors in the system.

LP5907
As a good design practice, keep the wiring parasitic inductance at a minimum, which means to use as wide as
possible traces from the LDO output to the capacitors, keeping the LDO output trace layer as close to ground
layer as possible and avoiding vias on the path. If there is a need to use vias, implement as many as possible
vias between the connection layers. The recommendation is to keep parasitic wiring inductance less than 35 nH.
For the applications with fast load transients, it is recommended to use an input capacitor equal to or larger to
the sum of the capacitance at the output node for the best load transient performance.
8.2.2.8 No-Load Stability

The LP5907 remains stable, and in regulation, with no external load.
8.2.2.9 Enable Control

The LP5907 may be switched ON or OFF by a logic input at the EN pin. A voltage on this pin greater than VIH
turns the device on, while a voltage less than VIL turns the device off.
When the EN pin is low, the regulator output is off and the device typically consumes less than 1 µA.
Additionally, an output pulldown circuit is activated which ensures that any charge stored on COUT is discharged
to ground.
If the application does not require the use of the shutdown feature, the EN pin can be tied directly to the IN pin to
keep the regulator output permanently on.
An internal 1-MΩ pulldown resistor ties the EN input to ground, ensuring that the device remains off if the EN pin
is left open circuit. To ensure proper operation, the signal source used to drive the EN pin must be able to swing
above and below the specified turnon or turnoff voltage thresholds listed in the Electrical Characteristics under
VIL and VIH.
8.2.3 Application Curves
1V/DIV
VOUT 100 mV/DIV
VOUT
1V/DIV LOAD 200 mA/DIV
EN
20 s/DIV 100 s/DIV

SVA-30180515 SVA-30180514
Figure 22. Start-Up Figure 23. Load Transient Response
9 Power Supply Recommendations

This device is designed to operate from an input supply voltage range of 2.2 V to 5.5 V. The input supply must
be well regulated and free of spurious noise. To ensure that the LP5907 output voltage is well regulated and
dynamic performance is optimum, the input supply must be at least VOUT + 1 V. A minimum capacitor value of 1
µF is required to be within 1 cm of the IN pin.

LP5907
10 Layout
10.1 Layout Guidelines

The dynamic performance of the LP5907 is dependant on the layout of the PCB. PCB layout practices that are
adequate for typical LDOs may degrade the PSRR, noise, or transient performance of the LP5907.
Best performance is achieved by placing CIN and COUT on the same side of the PCB as the LP5907, and as
close to the package as is practical. The ground connections for CIN and COUT must be back to the LP5907
ground pin using as wide and short a copper trace as is practical.
Connections using long trace lengths, narrow trace widths, and/or connections through vias must be avoided.
These add parasitic inductances and resistance that results in inferior performance especially during transient
conditions
10.1.1 X2SON Mounting

The X2SON package thermal pad must be soldered to the printed circuit board for proper thermal and
mechanical performance. For more information, see the QFN/SON PCB Attachment application report.
10.1.2 DSBGA Mounting

The DSBGA package requires specific mounting techniques, which are detailed in AN-1112 DSBGA Wafer Level
Chip Scale Package. For best results during assembly, alignment ordinals on the PC board may be used to
facilitate placement of the DSBGA device.
10.1.3 DSBGA Light Sensitivity

Exposing the DSBGA device to direct light may cause incorrect operation of the device. Light sources such as
halogen lamps can affect electrical performance if they are situated in proximity to the device. Light with
wavelengths in the red and infrared part of the spectrum have the most detrimental effect; thus, the fluorescent
lighting used inside most buildings has very little effect on performance.
10.2 Layout Examples

VIN VOUT
CIN 1 IN OUT 5 COUT
GND GND
2 GND
Enable
3 EN N/C 4
Figure 24. LP5907MF-x.x (SOT-23) Typical Layout

LP5907
Layout Examples (continued)
VOUT LP5907SN VIN

1 4
COUT CIN
2 3
Power Ground
VEN
Figure 25. LP5907SN-xx (X2SON) Typical Layout
VIN VOUT
LP5907UV
A1 A2
CIN COUT
B1 B2
Power Ground
VEN
Figure 26. LP5907A/UV-x.x (DSBGA) Typical Layout

LP5907
11 Device and Documentation Support
11.1 Documentation Support

11.1.1 Custom Design With WEBENCH® Tools
Click here to create a custom design using the LP5907 device with the WEBENCH® Power Designer.
1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements.
2. Optimize the design for key parameters such as efficiency, footprint, and cost using the optimizer dial.
3. Compare the generated design with other possible solutions from Texas Instruments.
The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time
pricing and component availability.
In most cases, these actions are available:
• Run electrical simulations to see important waveforms and circuit performance
• Run thermal simulations to understand board thermal performance
• Export customized schematic and layout into popular CAD formats
• Print PDF reports for the design, and share the design with colleagues
Get more information about WEBENCH tools at www.ti.com/WEBENCH.
11.1.2 Related Documentation

For related documentation, see the following:
• AN-1112 DSBGA Wafer Level Chip Scale Package
• QFN/SON PCB Attachment Application Report
11.2 Receiving Notification of Documentation Updates

To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.3 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.4 Trademarks
E2E is a trademark of Texas Instruments.
WEBENCH is a registered trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.

LP5907
12 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

PACKAGE OPTION ADDENDUM
www.ti.com 8-Oct-2018
PACKAGING INFORMATION
Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)
LP5907A28YKMR ACTIVE DSBGA YKM 4 3000 Green (RoHS SAC396 Level-1-260C-UNLIM -40 to 125 Q
& no Sb/Br)
LP5907A29YKMR PREVIEW DSBGA YKM 4 3000 TBD Call TI Call TI -40 to 125
LP5907A33YKMR ACTIVE DSBGA YKM 4 3000 Green (RoHS Call TI Level-1-260C-UNLIM -40 to 125 N
& no Sb/Br)
LP5907MFX-1.2/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LLTB
& no Sb/Br)
LP5907MFX-1.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LN8B
& no Sb/Br)
LP5907MFX-1.8/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LLUB
& no Sb/Br)
& no Sb/Br)
LP5907MFX-2.8/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LLYB
& no Sb/Br)
& no Sb/Br)
LP5907MFX-2.9/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 1E5X
& no Sb/Br)
LP5907MFX-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LLZB
& no Sb/Br)
& no Sb/Br)
& no Sb/Br)
LP5907MFX-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LLVB
& no Sb/Br)
LP5907MFX-4.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LLXB
& no Sb/Br)
LP5907SNX-1.2/NOPB ACTIVE X2SON DQN 4 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 CF
& no Sb/Br)
LP5907SNX-1.8/NOPB ACTIVE X2SON DQN 4 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 CG
& no Sb/Br)
Addendum-Page 1
(1) Drawing Qty (2) (6) (3) (4/5)
LP5907SNX-1.9 ACTIVE X2SON DQN 4 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 3Z
& no Sb/Br)
LP5907SNX-2.2/NOPB ACTIVE X2SON DQN 4 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 EP
& no Sb/Br)
LP5907SNX-2.5/NOPB ACTIVE X2SON DQN 4 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 F9
& no Sb/Br)
LP5907SNX-2.7/NOPB ACTIVE X2SON DQN 4 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 CH
& no Sb/Br)
LP5907SNX-2.75 ACTIVE X2SON DQN 4 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 HI
& no Sb/Br)
LP5907SNX-2.8/NOPB ACTIVE X2SON DQN 4 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 CI
& no Sb/Br)
LP5907SNX-2.85/NOPB ACTIVE X2SON DQN 4 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 CJ
& no Sb/Br)
LP5907SNX-2.9/NOPB ACTIVE X2SON DQN 4 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 GV
& no Sb/Br)
LP5907SNX-3.0/NOPB ACTIVE X2SON DQN 4 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 CK
& no Sb/Br)
LP5907SNX-3.1/NOPB ACTIVE X2SON DQN 4 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 CL
& no Sb/Br)
LP5907SNX-3.2/NOPB ACTIVE X2SON DQN 4 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 CM
& no Sb/Br)
LP5907SNX-3.3/NOPB ACTIVE X2SON DQN 4 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 CN
& no Sb/Br)
LP5907SNX-4.0/NOPB ACTIVE X2SON DQN 4 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 GU
& no Sb/Br)
LP5907SNX-4.5/NOPB ACTIVE X2SON DQN 4 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 CO
& no Sb/Br)
LP5907UVE-1.2/NOPB ACTIVE DSBGA YKE 4 250 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 R
& no Sb/Br)
LP5907UVE-1.8/NOPB ACTIVE DSBGA YKE 4 250 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 S
& no Sb/Br)
LP5907UVE-2.8/NOPB ACTIVE DSBGA YKE 4 250 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 U
& no Sb/Br)
LP5907UVE-2.85/NOPB ACTIVE DSBGA YKE 4 250 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 V
& no Sb/Br)
Addendum-Page 2
(1) Drawing Qty (2) (6) (3) (4/5)
LP5907UVE-3.0/NOPB ACTIVE DSBGA YKE 4 250 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 B
& no Sb/Br)
LP5907UVE-3.1/NOPB ACTIVE DSBGA YKE 4 250 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 X
& no Sb/Br)
LP5907UVE-3.2/NOPB ACTIVE DSBGA YKE 4 250 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 C
& no Sb/Br)
LP5907UVE-3.3/NOPB ACTIVE DSBGA YKE 4 250 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 D
& no Sb/Br)
LP5907UVE-4.5/NOPB ACTIVE DSBGA YKE 4 250 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 Z
& no Sb/Br)
LP5907UVX-1.2/NOPB ACTIVE DSBGA YKE 4 3000 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 R
& no Sb/Br)
LP5907UVX-1.6/NOPB ACTIVE DSBGA YKE 4 3000 Green (RoHS SAC396 Level-1-260C-UNLIM -40 to 125 J
& no Sb/Br)
LP5907UVX-1.8/NOPB ACTIVE DSBGA YKE 4 3000 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 S
& no Sb/Br)
LP5907UVX-2.2/NOPB ACTIVE DSBGA YKE 4 3000 Green (RoHS Call TI Level-1-260C-UNLIM -40 to 125 5
& no Sb/Br)
LP5907UVX-2.5/NOPB ACTIVE DSBGA YKE 4 3000 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 E
& no Sb/Br)
LP5907UVX-2.8/NOPB ACTIVE DSBGA YKE 4 3000 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 U
& no Sb/Br)
LP5907UVX-2.85/NOPB ACTIVE DSBGA YKE 4 3000 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 V
& no Sb/Br)
LP5907UVX-3.0/NOPB ACTIVE DSBGA YKE 4 3000 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 B
& no Sb/Br)
LP5907UVX-3.1/NOPB ACTIVE DSBGA YKE 4 3000 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 X
& no Sb/Br)
LP5907UVX-3.2/NOPB ACTIVE DSBGA YKE 4 3000 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 C
& no Sb/Br)
LP5907UVX-3.3/NOPB ACTIVE DSBGA YKE 4 3000 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 D
& no Sb/Br)
LP5907UVX-4.5/NOPB ACTIVE DSBGA YKE 4 3000 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 Z
& no Sb/Br)
LP5907UVX19/NOPB ACTIVE DSBGA YKE 4 3000 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 8
& no Sb/Br)
Addendum-Page 3
(1) Drawing Qty (2) (6) (3) (4/5)
LP5907UVX37/NOPB ACTIVE DSBGA YKE 4 3000 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 9
& no Sb/Br)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LP5907 :
• Automotive: LP5907-Q1
Addendum-Page 4
NOTE: Qualified Version Definitions:
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 5
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Aug-2018
TAPE AND REEL INFORMATION
*All dimensions are nominal

Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1
Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LP5907A28YKMR DSBGA YKM 4 3000 178.0 8.4 0.74 0.74 0.54 4.0 8.0 Q1
LP5907A33YKMR DSBGA YKM 4 3000 178.0 8.4 0.74 0.74 0.54 4.0 8.0 Q1
LP5907MFX-1.2/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LP5907SNX-1.2/NOPB X2SON DQN 4 3000 180.0 9.5 1.16 1.16 0.63 4.0 8.0 Q2
LP5907SNX-1.9 X2SON DQN 4 3000 180.0 9.5 1.16 1.16 0.63 4.0 8.0 Q2
Pack Materials-Page 1

(mm) W1 (mm)
LP5907SNX-2.75 X2SON DQN 4 3000 180.0 9.5 1.16 1.16 0.63 4.0 8.0 Q2
LP5907UVE-1.2/NOPB DSBGA YKE 4 250 178.0 8.4 0.71 0.71 0.51 2.0 8.0 Q1
LP5907UVX-1.2/NOPB DSBGA YKE 4 3000 178.0 8.4 0.71 0.71 0.51 2.0 8.0 Q1

(mm) W1 (mm)
LP5907UVX19/NOPB DSBGA YKE 4 3000 178.0 8.4 0.74 0.74 0.5 2.0 8.0 Q1
*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LP5907A28YKMR DSBGA YKM 4 3000 220.0 220.0 35.0
LP5907A33YKMR DSBGA YKM 4 3000 220.0 220.0 35.0
LP5907MFX-1.2/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LP5907SNX-1.2/NOPB X2SON DQN 4 3000 184.0 184.0 19.0
LP5907SNX-1.9 X2SON DQN 4 3000 184.0 184.0 19.0
LP5907SNX-2.75 X2SON DQN 4 3000 184.0 184.0 19.0
LP5907UVE-1.2/NOPB DSBGA YKE 4 250 210.0 185.0 35.0
LP5907UVX-1.2/NOPB DSBGA YKE 4 3000 210.0 185.0 35.0
LP5907UVX19/NOPB DSBGA YKE 4 3000 220.0 220.0 35.0
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated

LP 5907

Uploaded by

Document Informationclick to expand document informationlp5907

Document Informationclick to expand document information

Copyright:

Available Formats

LP 5907

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LP 5907

Uploaded by

Copyright:

Available Formats

Product Order Technical Tools & Support & Reference

Folder Now Documents Software Community Design

LP5907 250-mA, Ultra-Low-Noise, Low-IQ LDO

INPUT IN OUT OUTPUT

Changes from Revision M (January 2018) to Revision N Page

• Added Overshoot on start-up with EN row to Electrical Characteristics table ...................................................................... 7

Changes from Revision L (August 2016) to Revision M Page

• Added links for WEBENCH ................................................................................................................................................... 1

Changes from Revision K (May 2016) to Revision L Page

Changes from Revision J (March 2016) to Revision K Page

Changes from Revision I (August 2015) to Revision J Page

Changes from Revision H (November 2014) to Revision I Page

2 Submit Documentation Feedback Copyright © 2012–2018, Texas Instruments Incorporated

Product Folder Links: LP5907

• Added "SOT-23, X2SON packages" to second row of ΔVout spec ...................................................................................... 6

Changes from Revision G (October 2013) to Revision H Page

Copyright © 2012–2018, Texas Instruments Incorporated Submit Documentation Feedback 3

5 Pin Configuration and Functions

YKE and YKM Packages

Pin Functions: DSBGA

DQN Package DBV Package

Pin Functions: X2SON, SOT-23

4 Submit Documentation Feedback Copyright © 2012–2018, Texas Instruments Incorporated

Product Folder Links: LP5907

6.2 ESD Ratings

6.3 Recommended Operating Conditions

Copyright © 2012–2018, Texas Instruments Incorporated Submit Documentation Feedback 5

6.4 Thermal Information

6.5 Electrical Characteristics

6 Submit Documentation Feedback Copyright © 2012–2018, Texas Instruments Incorporated

Product Folder Links: LP5907

Electrical Characteristics (continued)

(9) This specification is verified by design.

6.6 Output and Input Capacitors

Copyright © 2012–2018, Texas Instruments Incorporated Submit Documentation Feedback 7

6.7 Typical Characteristics

Figure 1. Quiescent Current vs Input Voltage Figure 2. VEN Thresholds vs VIN

Figure 3. VOUT vs VIN Figure 4. VOUT vs VIN

Figure 5. Ground Current vs Output Current Figure 6. Load Regulation

8 Submit Documentation Feedback Copyright © 2012–2018, Texas Instruments Incorporated

Product Folder Links: LP5907

Typical Characteristics (continued)

Figure 7. ΔVOUT vs Temperature Figure 8. Line Regulation

VIN = VEN VIN 1V/DIV

Figure 9. Inrush Current Figure 10. Line Transient

VOUT 10 mV/ VOUT 100 mV/DIV

LOAD 200 mA/DIV

10 s/DIV 100 s/DIV

Figure 11. Line Transient Figure 12. Load Transient

Copyright © 2012–2018, Texas Instruments Incorporated Submit Documentation Feedback 9

Typical Characteristics (continued)

VOUT 100 mV/DIV VOUT 100 mV/DIV

LOAD 200 mA/DIV

Figure 13. Load Transient Figure 14. Load Transient

Figure 15. Start-Up Figure 16. Start-Up

10 Submit Documentation Feedback Copyright © 2012–2018, Texas Instruments Incorporated

Product Folder Links: LP5907