RT500 Manual 006 LR

Salus RT500 Manual 006_89 24/07/2013 10:27 Page 1
Digital Room Thermostat
Instruction Manual
Model No RT500
PRODUCT COMPLIANCE
This product complies with the essential requirements of the
following EC Directives:
• Electro-Magnetic Compatibility directive 2004/108/EC
• Low Voltage Directive 2006/95/EEC
• EC Marking directive 93/68/EEC
SAFETY INFORMATION
These instructions are applicable to the SALUS Controls model
stated on the front cover of this manual only, and must not be used
with any other make or model.
These instructions are intended to apply in the United Kingdom

only, and should be followed along with any other statutory
obligations.
This accessory must be fitted by a Competent person, and

installation must comply with the guidance provided in the current
editions of BS7671 (IEE Wiring Regulations) and Part ‘P’ of the
Building Regulations. Failure to comply with the requirements of
these publications could lead to prosecution.
Always isolate the AC Mains supply before opening or

removing the unit from the wall or wall box.
When fitting batteries don’t mix old and new batteries

together. Do not use rechargable batteries.
Please leave these instructions with the end user where they should
be kept in a safe place for future reference.
2 RT500 INSTRUCTION MANUAL

What is a programmable room thermostat?

... an explanation for householders
A programmable room thermostat is both a programmer and a room thermostat.
A programmer allows you to set ‘On’ and ‘Off’ time periods to suit your own lifestyle.
A room thermostat works by sensing the air temperature, switching on the heating
when the air temperature falls below the thermostat setting, and switching it off
once this set temperature has been reached.
So, a programmable room thermostat lets you choose what times you want the
heating to be on, and what temperature it should reach while it is on. It will allow
you to select different temperatures in your home at different times of the day
(and days of the week) to meet your particular needs.
Turning a programmable room thermostat to a higher setting will not make the
room heat up any faster. How quickly the room heats up depends on the design of
the heating system, for example, the size of boiler and radiators.
Neither does the setting affect how quickly the room cools down. Turning a
programmable room thermostat to a lower setting will result in the room being
controlled at a lower temperature, and saves energy.
The way to set and use your programmable room thermostat is to find the lowest
temperature settings that you are comfortable with at the different times you have
chosen, and then leave it alone to do its job. The best way to do this is to set low
temperatures first, say 18°C, and then turn them up by one degree each day until you
are comfortable with the temperatures. You won’t have to adjust the thermostat
further. Any adjustments above these settings will waste energy and cost you more
money.
If your heating system is a boiler with radiators, there will usually be only one
programmable room thermostat to control the whole house. But you can have
different temperatures in individual rooms by installing thermostatic radiator valves
(TRVs) on individual radiators. If you don’t have TRVs, you should choose a
temperature that is reasonable for the whole house. If you do have TRVs, you can
choose a slightly higher setting to make sure that even the coldest room is
comfortable, then prevent any overheating in other rooms by adjusting the TRVs.
The time on the programmer must be correct. Some types have to be adjusted in
spring and autumn at the changes between Greenwich Mean Time and British
Summer Time.
You may be able to temporarily adjust the heating programme, for example,
‘Override’, ‘Advance’ or ‘Boost’. These are explained in the manufacturer’s
instructions.
Programmable room thermostats need a free flow of air to sense the temperature, so
they must not be covered by curtains or blocked by furniture. Nearby electric fires,
televisions, wall or table lamps may prevent the thermostat from working properly.
RT500 INSTRUCTION MANUAL 3

INTRODUCTION
The RT500 from SALUS Controls is a stylish and accurate 5/2 or 7 day
programmable electronic thermostat with a large, easy to read Liquid
Crystal Display (LCD). This programmable thermostat has been specifically
designed to be used Volt Free.
Features
• 5/2 or 7 day programming flexibility
• Built-in start up programming
for quick installation
• Volt free contacts
• Frost protection
• Large, easy to read LCD
with blue backlight
• Burner on symbol
• User friendly
• Stylish casing
INSTALLATION
Please read the important safety information at the start of this manual
before you begin to install the thermostat.
The ideal position to locate the RT500 thermostat is about 1.5m above floor
level, in a location where the thermostat is accessible, reasonably lit and
free from extremes of temperature and draughts. Do not mount the
thermostat on an outside wall, above a radiator or in a location where it
may be subjected to direct sunlight.
The electrical connections to the RT500 are made to the supplied industry
standard backplate. This simplifies installation, as no connections are made
to the controller itself. Connection details are shown below - no Earth
connection is required for the correct and safe operation of the RT500, but
a parking terminal is provided to connect an Earth wire if one is present.

Backplate Connections
Terminal Description Backplate

L Mains Live
SL Switched Live
(Normally Open Contact)
Earth Parking (no electrical
connection)
After installing the backplate in a suitable location, wiring connections can be

made as shown above. The following criteria apply to the installation:
• The incoming AC mains supply should be 230V AC and fused at 5 amps.

• Optimum cable size for installation is 1.5 mm2; wiring colours should be
in accordance with the current requirements of the IEE Wiring Regulations.
• Cable entry should be from the rear of the backplate.
• All wiring connections should be securely made, and be firmly
gripped beneath the square brass washer on each terminal.
The RT500 requires two ‘AA’ alkaline batteries to function correctly. Ensure that
the batteries are inserted correctly, paying careful attention to the polarity
markings on the battery and next to the battery holders.
Do not restore the mains supply to the system until all associated items are fully
installed.
NOTE: All electrical installation work should be carried out by a suitably

qualified Electrician or other competent person. If you are not sure how to
install this thermostat consult either with a qualified electrician, heating
engineer or your boiler / heating system supplier for advice on how to continue.
Do not remove or refit the RT500 onto the backplate without

the mains supply to the system being isolated.

JUMPER SETTINGS
Changes to the jumper settings should only be made by the Engineer
carrying out the installation or other qualified person.
The installer should select the jumper position required if changes need to
be made to the factory default settings. These jumpers are found on the
rear of the thermostat.
Jumper Function Default

Temperature Movable jumper for ± 0.5 ºC span
Span ± 0.5 ºC or ± 1.0 ºC span.
Program Type Movable jumper for 5-2

5-2 or 7 individual days
programming.

AFTER INSTALLATION
After completing installation and powering up the RT500 for the first time
the thermostat will behave in the following way:
All the indicators on the display and the backlight will be turned on for two
seconds. After two seconds, the RT500 will then operate in Normal mode
(Normal mode is when the thermostat is displaying the room temperature).
The following table shows the settings of the RT500 digital thermostat after
Power on:
Function Status After Reset or Power On

Operation Mode Normal mode
Room Temperature 22.0 °C, updated within 5 seconds
°C indicator On
Clock 12:00
AM/PM indicator AM
Day of Week indicator M
Programme Default factory setting
Set Point Temperature Default factory setting
Programme Number indicator 1
SET indicator Off
PROG indicator Off
Frost Protection indicator Off
Heat indicator Off
Low-Battery Warning indicator Off, updated within 5 seconds
Output Relay Off

After Power on, the thermostat will operate in Normal mode
• The set point temperature is reset to the default setting

• The room temperature display is updated within 5 seconds
• The control process starts
• The programme number is updated to indicate the running program
If the Reset Button is pressed, the RT500 will behave in the same way as
described above, except that any previously saved user settings stored in
the internal memory will be deleted and overwritten with the default
settings, and all control settings will be returned to default values.
USER INTERFACE AND CONTROLS

The status and operation of the RT500 is clearly shown on the large
backlit Liquid Crystal Display (LCD).
This display allows the user a clear indication of the current room
temperature, and the status of the heating system.
There are few user controls for the RT500, making this thermostat
very easy to operate. These controls are shown below, along with a
description of each of their functions.

USER CONTROL FUNCTION SUMMARY
Key / Operation Symbol Functions
UP key Increases the selected setting
DOWN key Decreases the selected setting
BACKLIGHT / Manually turns on the LCD backlight

FROST key for 5 seconds, or activates /
deactivates Frost Protection
SELECT key Selects a clock or programme setting
SET key Sets a clock or programme setting
RESET button Resets the programmable thermostat

to default (original factory) settings
OPERATION
The RT500 is configured and adjusted
by the use of a minimal number of user
controls, and an intuitive user interface.
The backlit Liquid Crystal Display (LCD)

gives a highly visible, easily readable
indication of the programmable
thermostat status.

SETTING THE TIME

Press and hold SET and SELECT when the RT500 is in Normal mode for three
seconds to enter the Clock setting mode. Release both keys and the display
will look like the image below:
The Time and Day are displayed along with a SET indicator, with all other
indicators cleared from the display. The hour part of the time is flashing to
indicate that it is the currently selected item and is ready to be adjusted.
• Press the UP or DOWN keys to increase or decrease the ‘hour’ setting –

the selected item will stop flashing while a key is pressed, and will resume
flashing when you release the key.
• Press the SELECT key to select the ‘minutes’ section of the time. Set the
minutes in the same way as the hour by using the UP and DOWN keys.
• Press SELECT again to select the Day, and again change the setting with
the UP and DOWN keys.
• Press the SET key to confirm the new time and day settings. This will store
the changes and return the RT500 to Normal mode.
The RT500 will also return to Normal mode (and save the clock settings)
if no keys are pressed for more than 15 seconds.

PROGRAMMING THE RT500
The RT500 offers great versatility with its programming options, allowing
the user to programme the unit to operate on a 5/2 or 7 day control cycle.
The programmable thermostat has a default set of Programmes that have
been designed to meet the needs of most users. If these default
programmes are not suitable for your particular situation, reprogramming
the RT500 with your own settings is a very straightforward operation.
Selection of the default programming mode (5/2 or 7 day) is made by

changing the jumper setting on the rear of the RT500, as previously
described within the Installation section of this manual.
5/2 Day Mode
5/2 day mode is the default programming mode for the RT500. With this
mode selected, five different sets of time and set point temperatures can be
set for Weekdays or Weekends.
To review or change a programme, press the SET key when the RT500 is in
Normal mode. This will change the unit status to Programme Setting
mode.
The LCD display will display programme number 1 and SET PROG, with all
other indicators cleared. The weekdays will be flashing to indicate they are
the selected item and are ready to be adjusted:
Press the UP or DOWN key to select the programme set for either Weekday
or Weekend to be reviewed or adjusted. Pressing the SET key at any time
when in programming mode will return the RT500 into Normal mode.

Press the SELECT key to confirm the Weekday or Weekend selection. Once
this is set, the ‘Hour’ will flash to indicate that it is the selected item and is
the next item to be adjusted:
Press the UP or DOWN key to

adjust the hour setting to the
desired value, and confirm your
selection by pressing the SELECT
key.
Pressing the SELECT key allows you to step through each of the items to be
reviewed or adjusted within the programmes in the following sequence:
Programme Function Sequence
1 Hour Minutes Set point temperature
…before then allowing you to cycle back to Programme 1. Pressing the SET
key at any time will confirm the setting and return to the programme set
selection.

7 Day Mode
The RT500 also offers a 7 day programming mode, which allows you to
programme five different sets of time and set point temperatures for each
day of the week to give a total of 35 separate programme settings.
To review or change a programme, press the SET key when the RT500 is in
Normal mode. This will change the unit status to Programme Setting
mode.
The LCD display will display

programme number 1 and SET
PROG, with all other indicators
cleared. The weekdays will be
flashing to indicate they are the
selected item and are ready to be
adjusted.
Press the UP or DOWN key to

change the display to indicate the
single day you want to programme:
Pressing the SET key at any time when in programming mode will return
the RT500 into Normal mode. Press the SELECT key to confirm the Day
selection. Once this is set, the ‘Hour’ will flash to indicate that it is the
selected item and is the next item to be adjusted:
Press the UP or DOWN key to adjust the hour setting to the desired value,
and confirm your selection by pressing the SELECT key.

Pressing the SELECT key allows you to step through each of the items to be
reviewed or adjusted within the programmes in the following sequence:
Programme Function Sequence
…before then allowing you to cycle back to Programme 1. Pressing the SET
key at any time will confirm the setting and return to the programme set
selection. Each programme for all the other days of the week is set in exactly
the same way – just repeat the steps shown above, after entering
programming mode and selecting the day you want to programme.
Regardless of which programming mode the RT500 is set for (5/2 or 7 day),
not pressing any keys for 15 seconds will automatically save any
programming changes and exit to Normal mode. You can also review or
change programme settings when Frost Protection is enabled.

FROST PROTECTION
To enable the Frost Protection mode, press and hold the BACKLIGHT /
FROST button for three seconds with the RT500 in Normal mode. Once
Frost Protection is enabled, the set point temperature is automatically set
to 5°C to provide protection from the risk of freezing.
Whenever Frost Protection is activated, the Frost Protection indicator will

flash in the sequence shown below:
While Frost Protection is activated, it will override any programme settings

until the mode is changed. To turn off Frost Protection mode, press and
hold the BACKLIGHT / FROST button for three seconds.

Reviewing Set Point Temperature

You can view the set point temperature at any time by pressing
either the UP or DOWN key.
When any programme is running, the LCD

display will show the programme set point
temperature with the SET indicator
displayed:
When operating in Frost Protection mode,

the LCD display will show a reading of 5 °C
and also display the Frost Protection
indicator:
When operating in Temporary Override

mode, the LCD display will show the
temporary set point temperature:
To exit from the set point review, press any key except the UP or
DOWN keys, or don’t press any keys for approximately four seconds
– either of these actions will return the RT500 to Normal mode.

Temporary Override
It is possible to temporarily override the current set temperature of the
RT500. There are two ways to do this:
• While reviewing set point temperature: Pressing the UP or DOWN key

while reviewing the set point temperature will increase or decrease the
set point temperature in 0.5 °C steps.
• In Normal mode: press and hold either the UP or DOWN key to display
the set point temperature. After two seconds, the RT500 will enter
Temporary Override mode and allow increase or decrease of the set point
temperature. If the key is released within two seconds then you will only
be able to review the set point temperature.
Once in Temporary Override mode, the

clock and day are displayed, along with
the SET indicator; all other indicators
are cleared from the display. The set
point temperature will flash to indicate
that it can be changed:
Pressing the UP or DOWN key will increase or decrease the set point
temperature in 0.5 °C steps - the set point temperature can be adjusted
within a set range or 10 °C to 35 °C.
You can press SET at any time to confirm the new Temporary Override
setting and return to Normal mode, or press no keys at all and wait
approximately four seconds.
Temporary Override mode remains active until the clock or programme

settings are adjusted, Frost Protection is activated or the next programme
time / temperature set point is reached.

OTHER FUNCTIONS AND CONTROLS

Backlight
The backlight of the RT500 is switched on automatically whenever any of
the keys are pressed. The backlight will remain illuminated for
approximately 5 seconds after the last key press, except if you are
changing the set point temperature – in this case, the backlight will
remain illuminated throughout the setting change process.
The backlight will not illuminate if the RT500 battery is low.
Battery Status
The RT500 checks the battery voltage frequently during normal
operation. If the battery voltage is sensed as being low (this is normally
when the battery voltage falls to a level of around 2.6V), the low battery
indicator will be displayed on the screen.
Although the programmable thermostat will continue to operate

normally at this stage, you should replace the batteries as soon as possible
to prevent any possible operating problems.
Reset Button
The Reset Button is provided as a way to restore the programmable
thermostat to its default factory settings. Pressing this button will
delete any previously entered settings.

Sleep Mode
By pressing both the UP and DOWN keys together, the RT500 will enter
SLEEP mode. In this mode, all the RT500 functions will be paused to save
battery power.
While in SLEEP mode:
• The LCD display will be blank.

• All output from the thermostat will be turned off immediately.
• The clock will continue to run in the background.
Press any key to wake up the RT500 and cancel SLEEP mode.
ENERGY TIP
One way to set and use your room thermostat is to find the lowest
temperature setting that you are comfortable with, and then leave it set at
this temperature. You can do this by setting the room thermostat to a low
temperature, (for example 17 °C) and then increasing the setting by one
degree each day until you are comfortable with the room temperature -
you won’t have to adjust the thermostat further, as adjustment above this
setting will waste energy - a 1 °C increase in temperature is equal to 3% of
your heating costs.

MAINTENANCE
The RT500 programmable thermostat requires no special maintenance.
Periodically, the outer casing can be wiped clean using a dry cloth (please
DO NOT use solvents, polishes, detergents or abrasive cleaners, as these
can damage the thermostat).
There are no user serviceable parts within the unit; any servicing or repairs
should only be carried out by SALUS Controls or their appointed agents.
Should the RT500 programmable thermostat fail to

function correctly, check:
• The batteries are the correct type, fitted correctly and are not
exhausted - fit new batteries if in doubt.
• The RT500 temperature has been set correctly.

• Heating system is switched on.
WARRANTY
SALUS Controls warrants that this product will be free from any
defect in materials or workmanship, and shall perform in
accordance with its specification, for a period of two years from the
date of purchase. SALUS Controls sole liability for breach of this
warranty will be (at its option) to repair or replace the defective
product.

PRODUCT SPECIFICATION
Model: RT500
Type: Electronic programmable
thermostat, designed for volt
free heating applications.
Programming
Programming Modes: User selectable for 5/2 or 7 day option
Number of Programmes: Five (5) user programmes plus
factory default programme.
Override Facility: User selectable programme
override facility.
Default Programmes
Programme Output Weekday Weekend
1 ON 6:00 AM 6:00 AM
TEMP 21 ºC 21 ºC
2 ON 8:00 AM 8:00 AM
TEMP 14 ºC 21 ºC
3 ON 4:00 PM 4:00 PM
TEMP 21 ºC 21 ºC
4 ON 6:00 PM 6:00 PM
TEMP 21 ºC 21 ºC
5 ON 10:00 PM 10:00 PM
TEMP 14 ºC 14 ºC
Temperature
Scale: Celsius
Range: 5 ºC to 35 ºC
Resolution: 0.5 ºC
Tolerance: Less than ± 0.5 ºC at 25 ºC
Display Range: 5.0 ºC to 45.0 ºC
Display Resolution: 0.5 ºC

Clock
Accuracy: ± 1 minute per month
Display: 12 hour
Frost Protection
Setting: 5 ºC
Switching
Switching Voltage: 0 - 230V AC / 50Hz
Switching Current: 3A resistive, 1A inductive
Contact Type: Single Pole Single Throw (SPST)
Power Source
Power Source: 2 x AA alkaline batteries
(Don’t use rechargeable batteries)
Battery Life: Approximately 1 year
Temperature
Range: 5 ºC to 35 ºC
Accuracy: ± 0.5 ºC at 25 ºC
Environment
Operating Temperature: 0 ºC to + 50 ºC
Storage Temperature: - 20 ºC to + 55 ºC

RT500 Warranty
SALUS Controls warrants that this product will be free from any defect in
materials or workmanship, and shall perform in accordance with its
specification, for a period of two years from the date of purchase.
SALUS Controls sole liability for breach of this warranty will be (at its
option) to repair or replace the defective product.
Customer Name: ....................................................
Customer Address: ................................................
...............................................................................
Post Code: ..................... Tel No: ............................
Email: .....................................................................
Engineers Company: ..............................................
Tel No: ...................................................................
Email: ....................................................................
Intallation Date: .....................................................
Engineers Name: ....................................................
Engineers Signature: ..............................................

salus-tech.
Sales: Email: [email protected] Tel: 01226 323961
Technical: Email: [email protected] Tel: 01226 323961
SALUS Controls plc, SALUS House, Dodworth Business Park South,

Whinby Road, Dodworth, Barnsley S75 3SP

RT500 Manual 006 LR

Uploaded by

Copyright:

Available Formats

RT500 Manual 006 LR

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

RT500 Manual 006 LR

Uploaded by

Copyright:

Available Formats

Salus RT500 Manual 006_89 24/07/2013 10:27 Page 1

Digital Room Thermostat

These instructions are intended to apply in the United Kingdom

This accessory must be fitted by a Competent person, and

Always isolate the AC Mains supply before opening or

When fitting batteries don’t mix old and new batteries

2 RT500 INSTRUCTION MANUAL

What is a programmable room thermostat?

RT500 INSTRUCTION MANUAL 3

4 RT500 INSTRUCTION MANUAL

Terminal Description Backplate

After installing the backplate in a suitable location, wiring connections can be

• The incoming AC mains supply should be 230V AC and fused at 5 amps.

NOTE: All electrical installation work should be carried out by a suitably

Do not remove or refit the RT500 onto the backplate without

RT500 INSTRUCTION MANUAL 5

Jumper Function Default

Program Type Movable jumper for 5-2

6 RT500 INSTRUCTION MANUAL

Function Status After Reset or Power On

RT500 INSTRUCTION MANUAL 7

After Power on, the thermostat will operate in Normal mode

• The set point temperature is reset to the default setting

USER INTERFACE AND CONTROLS

8 RT500 INSTRUCTION MANUAL

USER CONTROL FUNCTION SUMMARY

Key / Operation Symbol Functions

UP key Increases the selected setting

DOWN key Decreases the selected setting

BACKLIGHT / Manually turns on the LCD backlight

SELECT key Selects a clock or programme setting

SET key Sets a clock or programme setting

RESET button Resets the programmable thermostat

The backlit Liquid Crystal Display (LCD)

RT500 INSTRUCTION MANUAL 9

SETTING THE TIME

• Press the UP or DOWN keys to increase or decrease the ‘hour’ setting –

10 RT500 INSTRUCTION MANUAL

PROGRAMMING THE RT500

Selection of the default programming mode (5/2 or 7 day) is made by

5/2 Day Mode

RT500 INSTRUCTION MANUAL 11

Press the UP or DOWN key to

Programme Function Sequence

1 Hour Minutes Set point temperature

2 Hour Minutes Set point temperature

3 Hour Minutes Set point temperature

4 Hour Minutes Set point temperature

5 Hour Minutes Set point temperature

12 RT500 INSTRUCTION MANUAL

The LCD display will display

Press the UP or DOWN key to

RT500 INSTRUCTION MANUAL 13

Programme Function Sequence

1 Hour Minutes Set point temperature

2 Hour Minutes Set point temperature

3 Hour Minutes Set point temperature

4 Hour Minutes Set point temperature