SERVICE MANUAL

PT92 CHASSIS

Modification reserved
 PT-92 Chassis Service Manual

CONTENTS

PAGE
1.Technical Data 4
2. Recommendation for service repairs 5
3. Handling of MOS chip components 5
4. X-Ray radiation precaution 5
5. Service Menu 6
6. Specification of the connector (Euroscart) 9
7. Component descriptions 10
8. Exploded view 11
9. Block Diagrams 14
10. Fault tracing diagram-power supply 17
11. Power Supply circuit diagram 18
12. Troubleshooting guide for main PCB 19
13. Descriptions of the integrated circuits
- TDA16846 SMPS IC 20
- TDA935X UOC IC 24
- TDA9875A TV SOUND IC (STEREO) 31
- TDA9870A TV SOUND IC (G. STEREO) 38
- TDA24C16 EEPROM 48
- TDA8351 VERTICAL IC (110O) 50
- TDA8356 VERTICAL IC (90O) 54
- TDA2616 STEREO AUDIO AMPLIFIER (110O) 58
- TDA2615 STEREO AUDIO AMPLIFIER (90O) 60
- TDA7056 MONO AUDIO AMPLIFIER (90O) 63
- TDA7057AQ HP AMPLIFIER 65
- TDA7050 HP AMPLIFIER 67
- TDA6107Q VIDEO OUTPUT AMPLIFIER 70
- TCDT1100 OPTO COUPLER 72
- TDA9830 TV SOUND AM DEMODULATOR 74
- TDA7710 DOLBY PRO LOGIC SURROUND 78
- BU2508AF HORIZONTAL TRANSISTOR (110O) 83
- BU508DF HORIZONTAL TRANSISTOR (90O) 86
- SPP03N60S5 SMPS MOSFET (90O) 89
- SPP04N60S5 SMPS MOSFET (110O) 91
14. Dolby and secam L mono board and circuits diagrams 93
15. Oscilloscope shapes 96
16. Chassis replacement part list 97
17. Main Circuit 113

3
PT-92 Chassis Service Manual

TECHNICAL DATA

CRT PANEL
Visible Picture 47 cm / 50 cm / 66 cm
Deflection Angle 90o / 110o
Vertical Frequency 50Hz
Horizontal Frequency 15.625Hz

ELECTRONIC
Program Number 100+AV
Teletext Flof text
Tuner Cable tuner - 8 MHz spacing for Hyper Band
TV System European CCIR system
Music Power 110o 2x8 Watt Rms 10% distortion
90o 2x4 Watt Rms 10% distortion

CONNECTIONS
Euro AV Socket Include

MAIN STAGE

Mains Voltage 165-260VAC

Mains Frequency 50Hz
Power Consumption 110o 126W; 90o 75W;
In Stby Mode 110o 8 Watt 90o 5 Watt

4
 PT-92 Chassis Service Manual

RECOMMENDATION FOR SERVICE REPAIRS

1- Use only original spare parts. Only use components ve a shock hazard from the receiver.
with the same specifications for replacement. Servicing should not be attempted by anyone who is
2- Original fuse value only should be used. not thoroughly familiar with the precautions
3- Main leads and connecting leads should be checked necessary when working on high voltage equipment.
for external damage before connection. Perfectly discharge the high potential of the picture
Check the insulation. tube before handling the tube. The picture tube is
4- Parts contributing to the safety of the product must highly evacuated and if broken.
not be damaged or obviously unsuitable. Glass fragments will be violently expelled.
This is valid especially for insulators and insulating Always discharge the picture tube anode to the rece-
parts. iver chassis to keep of the shock hazard before re-
5- Thermally loaded solder pads are to be sucked off moving the anode cap.
and re-soldered. 8- Keep wire away from the high voltage or high tempe-
6- Ensure that the ventilation slots are not obstructed. rature components.
7- Potentials as high as 25 KV are present when this re- 9- When replacing a wattage resistor in circuit board,
ceiver is operating. Operation of the receiver keep the resistor 10 mm away from circuit board.
outside the cabinet or with back cover removed invol-

HANDLING OF MOS CHIP COMPONENTS

MOS circuit requires special attention with regard to red in styropor materials or plastic magazines.
static charges. Static charges may occur with any high- 2- Persons have to rid themselves of electrostatic char-
ly insulating plastics and can be transferred to persons ges by touching MOS components.
wearing clothes and shoes made of synthetic materi-
als. Protective circuits on the inputs and outputs of mos 3- Hold the component by the body touching the termi-
circuits give protection to a limited extend only due to nals.
time of reaction. 4- Use only grounded instruments for testing and pro-
Please observe the following instructions to protect the cessing purposes.
components against damage from static charges. 5- Remove or connect MOS ICs when operating volta-
1- Keep mos components in conductive package until ge is disconnected.
they are used. Most components must never be sto-

X-RAY RADIATION PRECAUTION

1- Excessive high voltage can be produce potentially tage be recorded as a part of the service record. It is
hazardous X-RAY radiation. To avoid such hazard, important to use an accurate and reliable high volta-
the high voltage must not be above the specified li- ge meter.
mit. The nominal value of the high voltage of this re- 2- The primary source of X-RAY radiation in this TV re-
ceiver is 25KV at zero beam current (minimum ceiver is the picture tube. For continued X-RAY radi-
brightness) under 220V AC power source. The high ation protection, the replacement tube must be
voltage must not under any circumstance, exceed exactly the same type tube as specified in the part
30KV. It is recommended the reading of the high vol- list.

5
PT-92 Chassis Service Manual

SERVICE MENU

The service menu is entered by pressing the <SUB-PAGE> key on the RC and VOLUME-DOWN key on the TV simultane-
ously when the TV is in TV- mode. The service menu is left by pressing the <TV> key.
When entering the service mode the first menu item is IF (selection of normal IF). Next items can be selected using the keys
<PROGRAM-UP> and <PROGRAM-DOWN>. The value of each item can be changed using the keys <VOLUME-UP> and
<VOLUME-DOWN>. The item values are displayed as decimal values, except for the tuner-band-selection, BITS and option
items.
They are displayed as hexa-decimal values. All values are stored in non-volatile memory when the service menu is left. The
“INIT CTV832U” item initializes the NVM: It clears all names and tuning information of all programs and writes default valu-
es for the service alignments and preset values in NVM. While doing so, the OSD displays “BUSY”. When the initialization is
finished, the message “READY” is written on the screen.

Item DefauIt Explanation

IF 38.9 IF selection (58.8, 45.8, 38.9 or 38.00 MHz)
IFL1 33.9 IF for SECAM-L1 selection (33.4 or 33.9 MHz)
HP 31 Horizontal parallelogram
HB 31 Horizontal bow
EW 37 East-west Width for picture setting 16:9
PW 18 East-west Parabola for picture setting 16:9
UCP 13 East-west Upper Corner parabola for picture setting 16:9
LCP 13 East-west Lower Corner parabola for picture setting 16:9
TC 28 East-west Trapezium for picture setting 16:9
HP4:3 31 Horizontal parallelogram for picture setting 4:3
HB4:3 31 Horizontal bow for picture setting 4:3
EW4:3 45 East-west Width for picture setting 4:3
PW4:3 15 East-west Parabola for picture setting 4:3
UCP4:3 35 East-west Upper Corner parabola for picture setting 4:3
LCP4:3 25 East-west Lower Corner parabola for picture setting 4:3
TC4:3 31 East-west Trapezium for picture setting 4:3
HS 31 Horizontal Shift
VS 31 Vertical Slope
VA 31 Vertical Amplitude
SC 31 S-Correction
VSD off Vertical Scan Disable
VSH 31 Vertical Shift
VX 25 Vertical zoom (East-west only)
BLR 7 Black Level Red
BLG 7 Black Level Green
WPR 31 White point correction Red
WPG 31 White point correction Green
WPB 31 White point correction Blue
Ys 15 Y-delay adjustment for SECAM
Yn 8 Y-delay adjustment for NTSC
YP 0 Y-delay adjustment for PAL

6
 PT-92 Chassis Service Manual

Yo 0 Y-delay adjustment for external sources

AGC 4 AGC take over
CL 4 Cathode drive level
Bits 00 (ACL=0; FCO= 0; SVO= 0; HP2= 0; FSL= 0; OSO= 0)
Bits1 00 (FFI= 0; TV= 0; AV-1= 0; AV-2= 0; AV-2S= 0;
AV-3= 0; AV-3S= 0; AV = 0)
OptByte1 (Default=E3)
PAL-BG = Selection PAL-BG (1)
PAL-DK = Selection PAL-DK (1)
PAL-I = Selection PAL-I (0)
PAL-M = Selection PAL-M (0)
PAL-N = Selection PAL-N (0)
NTSC-M = Selection NTSC-M (1)
NTSC-443 = Selection NTSC-443 (1)
SECAM-BG = Selection SECAM-BG (1)
*(1) Selected, (0) Not Selected
OptByte2 (Default=07)
SECAM-DK = Selection SECAM-DK (1)
FRANCE = Selection FRANCE (1)
Logo = Enable/Disable Logo (1/0)
PalBG Scr = When the PalBG Scr selected, TV searches only
PalBG. Otherwise it searches all. (0)
AV2 = Selection AV2 (0)
*(1) Selected, (0) Not Selected
OptByte3 (Default=E8)
HP = Selection HP (0)
Volbar = Selection Volbar (1)
Subwof = Selection Subwof (0)
Presets = Selection Presets (1)
Lock = Selection Lock (1)
Hotel = When the Hotel mode selected, It’s impossible to
enter menu settings.lt selects the Hotel mode. (1)
*(1) Selected, (0) Not Selected
OptByte4 (Default=B8)
16:9 = Set 16:9 mode active (1)
110 = Selection 110/90 Tube (1/0)
Hpol = Default (0)
Vpol = DefauIt (0)
Field = Default (1)
FE-Out = Default (1)
Sw-on = When the power on the TV, it Enables or Disables
Standby Mode. (1/0)
Vg-Check = Default (1)
*(1) Selected, (0) Not Selected
OptByte5 (Default=09)
Clock = Enable/Disable Clock Menu (1)
AM/PM = Default (0)
AVL = Auto Volume Level (1)
1-norma = Default (0)
*(1) Selected, (0) Not Selected
OptByte6 (Default=00)
UOC-J = Default (0)
ignrSUP = Default (0)
ignrNDF = Default (0)
*(1) Selected, (0) Not Selected

7
PT-92 Chassis Service Manual

TSL 45 Start frequency of the low-band in MHz

TEL 118 End frequency of the low-band
TSM 118 Start frequency of the mid-band
TEM 400 End frequency of the mid-band
TSH 400 Start frequency of the high-band
TEH 863 End frequency of the high-band
TBL 03 hex Value needed for switching to the low-band
TBN 06 hex Value needed for switching to the mid-band
TBH 85 hex Value needed for switching to the high-band

16:9 / 4:3 Adjustment

The CTV832U software uses two sets of parameters for the registers HP (horizontal parallelogram), HB (horizontal
bow), EW (EW width), PW (parabola/width), UCP (upper corner parabola), LCP (lower corner parabola)
and IC (EW trapezium). They occur in the service menu for 16:9 screen with the listed abbreviations.
For the 4:3 screen there is a second set of these registers. They occur in the service menu with the extension ‘4:3’
(i.e. HP4:3, HB4:3,...).
Each register set must be adjusted under the right conditions i.e. the 16:9 settings are adjusted with a 16:9 picture -
the 4:3 settings with a 4:3 picture.
The inenu items EW, PW, UCP, LCP, TC, HP4:3, HB4:3,... TC4:3 and VX will only be in the service menu if the
option 16:9 is set in 4 th option byte.

TUNER PARAMETER IN SERVICE AND DEFINITION PHILIPS OREGA TEMIC SAMSUNG ALPS

TSL Start frequency of the low-band in MHz 45 45 45 45 45

TEL End frequency of the low-band 160 118 150 150 180

TSM Start frequency of the mid-band 160 118 150 150 180

TEM End frequency of the mid-band 440 400 440 425 465

TSH Start frequency of the high-band 440 400 440 425 465

TEH End frequency of the high-band 863 865 865 865 900

TBL hex Value needed for switching to the low-band A1 03 01 01 01

TBN hex Value needed for switching to the mid-band 92 06 02 02 02

TBH hex Value needed for switching to the high-band 34 85 04 08 0C

8
 PT-92 Chassis Service Manual

SPECIFICATIONS OF THE CONNECTOR

(EURO SCART)

I- Audio output 1. right channel 0.5 VRMS/<l k 0

2- Audio input 1. right channel 0.5 VRMS (connected to No.6)
3- Audio output 2. left channel 0.5 VRMS (connected to No.1)
4- GND (audio)
5- GND
6- Audio input 2. left channel 0.5 VRMS/>10k 0
7- RGB input, blue (B)
8- Switch signal video (status)
9- GND
10- Reserved for clock signals (not connected)
11- RGB input, green (G)
12- Reserved for remote control (not connected)
13- GND
14- GND switch signal RGB
15- RGB input, red (R)
16- Switch signal RGB
17- GND (video)
18- GND19- Video output 1 Vpp/75 ohm
20- Video input 1 Vpp/75 ohm
21- Shield

1 3 5 7 9 11 13 15 17 19 21

2 4 6 8 10 12 14 16 18 20

9
PT-92 Chassis Service Manual

POWER CORD

SAW FILTER

IR SENSOR

VOLTAGE REGULATOR

ON/OFF SWITCH

LINE FILTER
COMPONENT DESCRIPTIONS

PTC

NPN TRANSISTOR

PNP TRANSISTOR

CERAMIC FILTER

COIL

LINEARITY COIL

FUSIBLE RESISTOR

IW METAL OXIDE RESISTOR

1/2W METAL OXIDE RESISTOR

1/4 OR 1/6W CARBON FILM RESISTOR

CERAMIC CAPACITOR /POLYESTER CAPACITOR

ELECTROLYTIC CAPACITOR

DIODE

ZENER DIODE

SWITCH JUMPER

NET (INPUT)

NET (OUTPUT)

TACT SWITCH

10 10
 1- 28” MEGA CABINET
2- 28” FST CRT
3- CRT SCREW Ø 7x30
4- ACRYLIC WINDOW
5- MULTIPLE BUTTON
6- MULTIPLE BUTTON SCREW Ø 2.9x9.5
7- LOGO PCB
8- LOGO ACR.
9- LOGO
10- CRT PANEL STOPER
11- AV PCB
12- AV PCB HOLDER
13- AV HOLDER SCREW
14- ON-OFF BUTTON
15- FRAME MAIN PCB
16- MAIN PCB
17- CRT PCB
18- POWER CABLE
19- POWER CABLE HOLDER
20- SPEAKER

11
21- SPEAKER SCREW
22- TWEETER
23- TWEETER SCREW
24- BACK COWER
25- BACK COWER SCREW
26- BACK COWER LABEL
27- FRONT FRAME

28” MEGA CTV

PT-92 Chassis Service Manual
 1- 21” MEGA CABINET
2- ACRYLIC WINDOW 21” CRT
3- 21” CRT
4- CRT SCREW Ø 7x30
5- SPEAKER
6- SPEAKER SCREW Ø 3.9x10
7- CRT RUBBER
8- MULTIPLE BUTTON
9- MULTIPLE BUTTON SCREW Ø 2.9x9.5
10- AV PCB
11- AV PCB HOLDER
PT-92 Chassis Service Manual

12- AV HOLDER SCREW Ø 2.9x9.5

13- POWER CABLE HOLDER
14- POWER CABLE
15- LOGO PCB
16- LOGO ACR.
17- LOGO
18- MAIN PCB

12
19- ON-OFF BUTTON
20- CRT PCB
21- BACK COWER
22- BACK COWER SCREW Ø 3.9x19
23- BACK COWER LABEL
24- FRONT FRAME

21” MEGA CTV

 1- 20” MEGA CABINET
2- ACRYLIC WINDOW 20” CRT
3- 20” CRT
4- CRT SCREW Ø 7x30
5- SPEAKER
6- SPEAKER SCREW Ø 3.9x10
7- CRT RUBBER
8- MULTIPLE BUTTON
9- MULTIPLE BUTTON SCREW Ø 2.9x9.5
10- AV PCB
11- AV PCB HOLDER
12- AV HOLDER SCREW Ø 2.9x9.5
13- POWER CABLE HOLDER
14- POWER CABLE
15- LOGO PCB
16- LOGO ACR.
17- LOGO
18- MAIN PCB
19- ON-OFF BUTTON

13
20- CRT PCB
21- BACK COWER
22- BACK COWER SCREW Ø 3.9x19
23- BACK COWER LABEL
24- FRONT FRAME

20” MEGA CTV

PT-92 Chassis Service Manual
PT-92 Chassis Service Manual

PT92 110o STEREO CHASSIS

I2C STEREO
TDA2616 L
UV1316 PLL I2C
TDA9870A/75A
Tuner
Sound R
Sound Processor Amplifier
Scarts
AGC L/R

SAV Sub
Filter

IF
RGB
TDA6107Q
Iblack Triple RGB
Sound Output Amplifier 110o
Trap TDA935X/6X/8X
Vdrive
TDA8351
PAL/SECAM/NTSC Guard
DC Vertical Ver.
TV Signal Proc. Amplifier
Externals Teletext Decoder Beam
L/R µ-Controller Current
RGB Processing BU2508AF Hor.
Hdrive Horizontal
CVBS Deflection EHT
Flyback
& EHT
E/W (110o)

RGB

12.000

Supply Degaussing

TDA16846
Mains
I2C SMPS
≈ 220
PCA8521 16K
RC-5 Transmitter EEPROM

14
 PT-92 Chassis Service Manual

PT92 90o STEREO CHASSIS

I2C STEREO
TDA2615 L
UV1316 PLL I2C
TDA9870A/75A
Tuner
Sound R
Sound Processor Amplifier
Scarts
AGC L/R

SAV Sub
Filter

IF
RGB
TDA6107Q
Iblack Triple RGB
Sound Output Amplifier 90o
Trap TDA935X/6X/8X
Vdrive
TDA8356
PAL/SECAM/NTSC Guard
DC Vertical Ver.
TV Signal Proc. Amplifier
Externals Teletext Decoder
L/R µ-Controller Beam
RGB Processing Current Hor.
BU508DF
Hdrive
CVBS Horizontal EHT
Deflection
& EHT
Flyback

RGB

12.000

Supply Degaussing

TDA16846
Mains
2
IC SMPS
PCA8521 ≈ 220
16K
RC-5 Transmitter EEPROM

15
PT-92 Chassis Service Manual

PT92 90o MONO CHASSIS

I2C

UV1316 PLL
Tuner

AGC

SAV TDA7056A
Mono
Filter Sound
Audio Amplifier
Out
IF
RGB
TDA6107Q
Iblack Triple RGB
Sound Output Amplifier 90o
TDA935X/6X/8X
Trap
Vdrive
TDA8356
PAL/SECAM/NTSC Guard
DC Vertical Ver.
TV Signal Proc. Amplifier
Externals Teletext Decoder
µ-Controller Beam
RGB Processing Current Hor.
Mono BU508DF
Hdrive
CVBS Horizontal EHT
Deflection
& EHT
Flyback

RGB

12.000

Supply Degaussing

TDA16846 Mains
I2C SMPS ≈ 220
PCA8521
16K
RC-5 Transmitter
EEPROM

16
 PT-92 Chassis Service Manual

FAULT TRACING DIAGRAM-POWER SUPPLY

Switched mode power

supply defective,+145V
is missing or level is wrong

DP 01 ÷ 04 YES
CP 01 ÷ 04 Fuse
F1 defective
CP 06, TP01

NO

RP 07, RP 05 NO
open and Voltage at drain
short circuit TP 01

YES

YES Voltage at
RP 06 IP 01
PIN 11
< 1V

NO

YES
Start-up voltage
RP 11, DP 07 (6)
PIN 14
< 8V

NO

YES
TP 01 Start-up voltage
varies ca. 8V

NO

IP 01

Measure +145 V

NO +145V
VAP 1, RP 03 adjustable with
VAP 01

YES
Control range of
switched-mode
power supply

17
PT-92 Chassis Service Manual

POWER SUPPLY

18
 PT-92 Chassis Service Manual

TROUBLESHOOTING GUIDE FOR MAIN PCB

TROUBLE CHECK POINTS

No color CV37, CV38, XV01

Horizontal linearity LD02, RD20, DD06

Horizontal size +B voltage, CD18, CD20, CD27, CD08, TV06

Flue picture RD17, RD06, RD62, R001, Focus adjust

Dark picture Screen adjust, EHT voltage

Noise picture TU01, AGC adjust, If adjust

Interference TV01, TV04, TU01

No sound IA50, IA51, IA01, DP17, DP12, RA51, X301, I302, IV01

Sound distortion I302, IC01, L304, CA07, CA06, RA06, RA07, IA01, IA50, IA51

Memory IC02, IV01, TC10

No video on the SCART IV01, TE01, TE04

No audio on the SCART I302, TV03

No picture TD01, TD02, DD01, TD04, DD03, DD04, ID50, RD56, IV01

19
PT-92 Chassis Service Manual

TDA16846
Controller For Switch Mode Power Supplies

The TDA16846 is suited for TV-, VCR-sets and SAT receivers. It also can be good used in PC monitors.
The TDA 16847 is identical with TDA16846 but has an additional power measurement output (pin 8) which can be used
a Temporary High Power Circuit.

Pin Configuration (top view)

U
DTC 1 14 VCC

PCS 2 13 OUT

RZI 3 12 GND

SRC 4 11 PVC

OCI 5 10 FC1

FC2 6 9 REF

SYN 7 8 N.C./PMO

Pin Definitions and Functions

Pin Symbol Function
1 OTC Off Time Circuit
2 PCS Primary Current Simulation
3 RZI Regulation and Zero Crossing Input
4 SRC Soft-Start and Regulation Capacitor
5 OCI Opto Coupler Input
6 FC2 Fault Comparator 2
7 SYN Synchronization Input
8 N.C./PMO Not Connected (TDA16846)
9 REF Reference Voltage and Current
10 FC1 Fault Comparator 1
11 PVC Primary Voltage Check
12 GND Ground
13 OUT Output
14 VCC Supply Voltage

20
 PT-92 Chassis Service Manual

TDA16846 Block Diagrams

PVC

Fold Back Point Correction 11

D4 R4
SYN R6x1/3
Primary
KSY
Voltage
R7 ∞ Check
- PVA
R6 D5
5V + ∞ ∞
30kΩ - -
1V +
R8 R3 1.5V +

75kΩ 15kΩ
Control Voltage –
Off Time 3.5V
G1 VCC
Limit Comparator +
1
5V ∞
9
1
+ ED2
REF
OTC - 8
CS1 G4 N.C.
RSTC/RSTF
∞ 6
+ FC2
1
Eror –
3.5V R2
5V Amplifier Error-
D2 Flipflop FC2
∞ 1.2V
3 +
RZI S
- Q
R
D3 Buffer for
Control Voltage
4
SRC ∞
5
+
+
OCI -

R1 Output
On Time & G3 Driver
20kΩ Comparator
S & 13
∞ Q OUT
5V G2
2 - R
PCS + I1

ED1
Zero Crossing
1.5V Signal

D1 <25mV
Startup FC1
Diode Supply Voltage
Overvoltage
Comparator 1V ∞
Comparator -
14 ∞ ∞ +
VCC +
12
+
GND 16V - 15.8V -
10

1) The input with the lower voltage becomes operative

21
PT-92 Chassis Service Manual

ELECTRICAL CHARACTERISTICS
Absolute maximum ratings

All voltages listed are referenced to ground (0V, Vss) except where noted.
Parameter Symbol Limit Values Unit Remarks
Min. Typ.
Supply Voltage at Pin 14 Vcc -0.3 17 V -
Voltage at Pin 1, 4, 5, 6, 7, 9, 10 - -0.3 6 V -
Voltage at Pin 2, 8, 11 - -0.3 17 V -
Voltage at Pin 3 RZI 6 V -
Current into Pin 3 -10 mA V3 < - 0.3V
Current into Pin 9 REF -1 - mA -
Current into Pin 13 OUT 100 mA V13 > - Vcc
-100 mA V13 < - 0V
ESD Protection - - 2 kV MIIL STD 883C
methot 3015.6,
100 PF, 1500Ω
o
Storage Temperature Tstg -65 125 C -
o
Operating Junction Temperature Tj - 125 C -
Thermal Resistance RthJA - 110 K/W P-DIP-14-3
Junction-Ambient
o
Soldering Temperature - - 260 C -
Soldering Time - - 10 s -

Note: Stresses above those listed here may cause permanent damage to the device. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.

22