Scribd Logo
Upload

Welcome to Scribd!

  • 131 views

    Xs Chamfer Accuracy Factor

    Uploaded by

    sixramesh123
    This document discusses the XS_CHAMFER_ACCURACY_FACTOR advanced option in Tekla Structures software. The option defines the number of points used to construct chamfers, with lower values increasing points and smoothing curves, and higher values decreasing points and making curves less smooth. The default value is 4.0, and changing it requires a Tekla Structures restart. Each object supports up to 99 points, and exceeding that could break part geometry. The setting affects visual accuracy but not DSTV file accuracy.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Xs Chamfer Accuracy Factor

    Uploaded by

    sixramesh123
    131 views2 pages
    This document discusses the XS_CHAMFER_ACCURACY_FACTOR advanced option in Tekla Structures software. The option defines the number of points used to construct chamfers, with lower values increasing points and smoothing curves, and higher values decreasing points and making curves less smooth. The default value is 4.0, and changing it requires a Tekla Structures restart. Each object supports up to 99 points, and exceeding that could break part geometry. The setting affects visual accuracy but not DSTV file accuracy.

    Original Description:

    TEKLA Xs_Chamfer_Accuracy_Factor

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document discusses the XS_CHAMFER_ACCURACY_FACTOR advanced option in Tekla Structures software. The option defines the number of points used to construct chamfers, with lower values increasing points and smoothing curves, and higher values decreasing points and making curves less smooth. The default value is 4.0, and changing it requires a Tekla Structures restart. Each object supports up to 99 points, and exceeding that could break part geometry. The setting affects visual accuracy but not DSTV file accuracy.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    131 views2 pages

    Xs Chamfer Accuracy Factor

    Uploaded by

    sixramesh123
    This document discusses the XS_CHAMFER_ACCURACY_FACTOR advanced option in Tekla Structures software. The option defines the number of points used to construct chamfers, with lower values increasing points and smoothing curves, and higher values decreasing points and making curves less smooth. The default value is 4.0, and changing it requires a Tekla Structures restart. Each object supports up to 99 points, and exceeding that could break part geometry. The setting affects visual accuracy but not DSTV file accuracy.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    XS_CHAMFER_ACCURACY_FACTOR | Tekla User Assistance Page 1 of 2

    2016I TABLE OF CONTENTS

    Advanced optio… › Alphabetical list… › C › XS_CHAMFER…

    Added August 31, 2016 by Tekla User Assistance | Software version: 2016i

    XS_CHAMFER_ACCURACY_FACTOR

    Category
    Speed and accuracy
    Use this advanced option to define the number of points used for chamfers. Use lower values to
    increase the number of points used to construct the chamfer, thus making the curved chamfer
    smoother. Use larger values to decrease the number of points used to construct the chamfer, thus
    making the curved chamfer less smoother.
    The default value is 4.0.
    Restart Tekla Structures after changing the value to activate the new setting.
    Each object can only support up to 99 points, so if your contour plates are too complex or too
    round, the maximum number of points may be exceeded and the part geometry may break.

    NOTE:
    Even though the XS_CHAMFER_ACCURACY_FACTOR setting changes the appearance of the
    curved chamfers in the model, it does not affect the accuracy of the DSTV file.

    In the example below, the value is 16.

    In the example below, the value is 1.

    https://teklastructures.support.tekla.com/2016i/en/xs_chamfer_accuracy_factor?launcher=1001 24-08-2017
    XS_CHAMFER_ACCURACY_FACTOR | Tekla User Assistance Page 2 of 2

    Click the links below to find out more:


    Round chamfers does not appear round in model
    Chamfer accuracy for polybeams and contour plates

    Quick feedback
    Did you find what you were looking for? *
    Yes
    Partly
    No

    Submit

    https://teklastructures.support.tekla.com/2016i/en/xs_chamfer_accuracy_factor?launcher=1001 24-08-2017

    You might also like