Scribd
Upload
274 views3 pages

Casting Process Advantages and Limitations

castinfg detailed explanation

Uploaded by

a
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
274 views3 pages

Casting Process Advantages and Limitations

castinfg detailed explanation

Uploaded by

a
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Casting Process – Advantages and Limitations

me-mechanicalengineering.com/casting-process-advantages-and-limitations/

By Vinodh Reddy Chennu 9/13/2016

Casting is also known as foundering, is the oldest manufacturing process in which liquid molten metal is poured into
a perforated casting cavity of refractory material. Allow liquid metal to solidify, after solidification the casting metal
can be taken out by breaking the mould. Casting process is used to produce components such as pistons, mill rolls,
wheels, cylinder blocks, liners, machine tool beds.

Different terminology used in casting process are moulding sand, baking sand, facing sand, loam sand, parting
sand, CO2 sand, flak, pattern, parting line, sprue, runner, ingate, riser, chill and chaplets.

Moulding sand:
Moulding sand is the refractory material used for making the mold. It is mixture of silica, clay and moisture to get
required properties.

Baking sand:
Baking sand consists of refractory material and it is made of used sand or burnt sand.

Facing sand:
Facing sand is the carboneous material sprinkled on the inner surfaces of the molding cavity for obtaining better
surface finish.

Loam sand:
Gree or dry sand with at least 50% clay and dries hard is called loam sand. It also contains fire clay. It has 18 to 20%
moisture and produces a good surface finish.
1/3
Parting sand:
For separating the moulds from adhering to each other by separating a fine sharp dry sand called parting sand. It
also can be used to keep green sand from sticking to the pattern. It is the clean clay free silica sand.

CO2 sand:
In the sand in-place of clay sodium silicate (Na2SiO3) is used, called as Carbon dioxide (CO 2) sand. When the CO 2
is supplied into this sand, it the CO2 will chemically react with sodium.

Flak:
Flak is the molding box used for holding the sand. Based on the situation it can be named as cope, drag, cheek etc.

Drag:
Lower molding flask is called drag.
Cope:
Upper molding flak is called cope.
Cheek:
The middle molding flask used in the three-piece pattern is called cheek.

Pattern:
The pattern is the replica of the casting to be produced.

Parting line:
The parting line is the dividing line between the two flasks.

Sprue:
Sprue is the connecting passage between the pouring basin and runner. It controls the flow of molten metal.

Runner:
The runner is the passage used for regulating the flow of molten liquid.

Ingate:
Ingate is the last point of gating from where the molten metal enters the cavity.

Riser:
The riser is the reservoir of molten metal provided in the casting process to compensate the liquid shrinkage’s taking
place during solidification.

Chill:
Chill is the metallic piece used for obtaining directional solidification.

Chaplets:
Chaplets are used for supporting the cores inside the mold cavity to take care of its own weight and mold cavity to
take care of its own weight and overcome the buoyancy forces.

Advantages of casting process:

Molten metal flows into ant small section in the molten cavity, hence any complex shape can be easily
produced.
Practically any type of material can be casted.
Ideal method is by producing small quantities
Due to small cooling rate from all directions, the properties of casting are same in all directions.
2/3
Any size of casting can be produced like up to 200 tons.
Casting is the often cheapest and most direct way of producing a shape with certain desired mechanical
properties.
Certain metals and alloys such as highly creep resistant metal-based alloys for gas turbines cannot be
worked mechanically and can be cast only.
Heavy equipment like machine leads, ship’s propeller etc. can be cast easily in the required size rather than
fabricating them by joining several small pieces.
Casting is best suited for composite components requiring different properties in different direction. These are
made by incorporating preferable inserts in a casting. For example, aluminium conductors into slots in iron
armature for electric motors, wear resistant skins onto shock resistant components.

Limitations of casting process:

With normal sand casting process, the dimensional accuracies and surface finish is less.
Defects are unavoidable.
Sand casting is labor intensive.

Casting
© Copyright 2016 ME Mechanical

3/3

You might also like