Arabian Journal of Chemistry (2014) xxx, xxx–xxx

King Saud University

Arabian Journal of Chemistry

www.ksu.edu.sa
www.sciencedirect.com

ORIGINAL ARTICLE

Kinetics and equilibrium study for the adsorption

of textile dyes on coconut shell activated carbon
Aseel M. Aljeboree a, Abbas N. Alshirifi b, Ayad F. Alkaim a,*

a
Department of Chemistry, College of Sciences for Women, Babylon University, Hilla, Iraq
b
Department of Chemistry, College of Sciences, Babylon University, Hilla, Iraq

Received 29 June 2013; accepted 28 January 2014

KEYWORDS Abstract The preparation of activated carbon from coconut husk with H2SO4 activation (CSAC)
Activated carbon; and its ability to remove textile dyes (maxilon blue GRL, and direct yellow DY 12), from aqueous
Adsorption; solutions were reported in this study. The adsorbent was characterized with Fourier transform infra-
Isotherm; red spectrophotometer (FT-IR), and scanning electron microscope (SEM). Various physiochemical
Kinetics; parameters such as, contact time, initial dye concentration, adsorbent dosage, particle size, pH of
Thermodynamics dye solution and temperature were investigated in a batch-adsorption technique. Result showed that
the adsorption of both GRL and DY 12 dyes was favorable at acidic pH. The adsorption uptake was
found to increase with increase in initial dye concentration, and contact time but decreases with the
amount of adsorbent, particle size, and temperature of the system. The chemisorption, intra-particle
diffuse, pseudo-first-order and pseudo-second-order kinetic models were applied to test the experi-
mental data. The pseudo-second order exhibited the best fit for the kinetic studies, which indicates that
adsorption of (GRL, and DY 12) is limited by chemisorption process. The equilibrium data were eval-
uated using Langmuir, Freundlich, Temkin and Fritz–Schlunder isotherms. The Fritz–Schlunder
model best describes the uptake of (GRL and DY 12) dye, which implies that the adsorption of textiles
dyes in this study onto coconut husk activated carbon is heterogeneous with multi-layers. Thermody-
namic parameters such as Gibbs free energy, enthalpy and entropy were determined. It was found that
(GRL and DY 12) dye adsorption was spontaneous and endothermic.
ª 2014 Production and hosting by Elsevier B.V. on behalf of King Saud University.

1. Introduction

Water pollution is one of the most undesirable environmental

* Corresponding author. Tel./fax: +964 7801324986. problems in the world and it requires solutions. Textile indus-
tries produce a lot of wastewater, which contains a number of
E-mail address: [email protected] (A.F. Alkaim).
contaminants, including acidic or caustic dissolved solids, toxic
Peer review under responsibility of King Saud University.
compounds, and any different dyes, many of these dyes are
carcinogenic, mutagenic, and teratogenic and also toxic to
human beings, fish species, and microorganisms. Hence, their
Production and hosting by Elsevier

1878-5352 ª 2014 Production and hosting by Elsevier B.V. on behalf of King Saud University.
http://dx.doi.org/10.1016/j.arabjc.2014.01.020

Please cite this article in press as: Aljeboree, A.M. et al., Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell acti-
vated carbon. Arabian Journal of Chemistry (2014), http://dx.doi.org/10.1016/j.arabjc.2014.01.020
2 A.M. Aljeboree et al.

removal from aquatic wastewater becomes environmentally et al., 2009), hazelnut husks, rice hulls, oil palm shell (Tan
important (Konicki et al., 2013). et al., 2008), and Coconut husk (Foo and Hameed, 2012).
Large quantities of dangerous dyes, pigments and metals The objective of this work is to study the static capacity of
originated from dye manufacturing, textile as well as pulp adsorption of textile dyes (GRL, and DY 12) by the prepared
and paper industries are emitted into wastewaters. This makes activated carbons derived by coconut shells (CSAC). The ef-
treating water contamination difficult , because the color tends fects of contact time, initial dye concentration, mass dosage,
to persist even after the conventional removal processes (Visa temperature, and pH on the static adsorption of the dye onto
et al., 2010). The dye contaminations in water tend to prevent the prepared CSAC were examined. The pseudo-first order and
light penetration and therefore, affect photosynthesis consider- pseudo-second order models are used to correlate the adsorp-
ably (Banerjee and Chattopadhyaya, 2013; Hajati et al., 2014; tion kinetics data of GRL and DY 12 onto prepared activated
Hameed et al., 2013). Due to the wide application of dye com- carbons. The kinetics as well as the diffusion parameters are
pound and their numerous hazard and toxic derivatives, the also evaluated. Thermodynamic studies have also been per-
cleaning of wastewater from color dyestuff becomes environ- formed to understand the processes of removal of the selected
mentally important (Ghaedi et al., 2013). Although, synthetic dyes on CSAC.
origins aromatic dyes are even biologically non-degradable
and their treatment by other effective conventional procedure 2. Experimental
is impossible.
There are several methods available for color removal from 2.1. Materials and methods
waters and wastewaters such as membrane separation, aerobic
and anaerobic degradation using various microorganisms,
Maxilon blue GRL [kmax = 599 nm] and direct yellow DY 12
chemical oxidation, coagulation and flocculation, and reverse
[kmax = 403 nm] were obtained from Al-Hillaß Textile Com-
osmosis. Some of these techniques have been shown to be
pany (Babylon, Iraq). The chemical structures of maxilon blue
effective however they have some limitations such as excess
GRL and direct yellow DY 12 are shown in Fig. 1. Concentra-
amount of chemical usage, accumulation of concentrated
tions of dyes were determined by finding out the absorbance at
sludge that has serious disposal problems and lack of effective
the characteristic wavelength using a double beam UV/Vis
color reduction. The adsorption technique, which is based on
spectrophotometer (UV–Visible spectrophotometer, Shimadzu
the transfer of pollutants from the solution to the solid phase,
1650). Calibration curves were plotted between absorbance
is known as one of the efficient and general wastewater treat-
and concentration of the dye solution.
ment method (Ghaedi et al., 2012). The method is superior
to other dye removal techniques in terms of initial cost, sim-
2.2. Preparation of H2SO4-activated carbon (CSAC)
plicity of design, ease of operation, and non-toxicity of the uti-
lized adsorbents compared to other conventional wastewater
treatment methods (Kismir and Aroguz, 2011). The cost effec- Coconut shells are obtained from the Iraqis local markets and
tiveness, availability and adsorptive properties are the main were used as precursors. Firstly, they were washed with dis-
criteria in selection of an adsorbent to remove organic com- tilled water to remove any adhering impurities, and then dried
pounds from wastewaters (Demirbas et al., 2008; Ghaedi at 110 C for 24 h followed by grinding and sieving in order to
et al., 2012), also application of adsorption procedure espe- use particles size ranged between 1 mm and 2 mm. H2SO4/acti-
cially based on non-toxic and green adsorbent with high sur- vated carbon sample (CSAC) was prepared via two steps: car-
face area and reactive surface atom is a great demand bonization of dried precursor at 500 C for 2 h in the absence
(Chiou and Chuang, 2006). of air using a muffle furnance (600 · 40 mm) at a rate of 10 C/
Activated carbon, a widely used adsorbent in industrial min up to 500 C. The carbonized sample was cooled and
processes, is composed of a microporous, homogenous struc- soaked with certain weight of H2SO4 (20 g of carbonized sam-
ture with high surface area and shows radiation stability (Iqbal ple with 60 g of H2SO4 (50%)) in 100 ml distilled water for
and Ashiq, 2007). The process for producing high-efficiency 24 h at room temperature, followed by drying at 110 C and
activated carbon is not completely investigated in developing finally activated at 600 C for 4 h. Prepared sample was
countries. Furthermore, there are many problems with the washed several times with distilled water till neutral filtrate
regeneration of used activated carbon. Nowadays, there is a and then dried at 110 C to constant weight and finally stored
great interest in finding inexpensive and effective alternatives in a clean dry glass bottle.
to the existing commercial activated carbon (AlOthman
et al., 2013). Exploring effective and low-cost activated carbon 2.3. Characterization of prepared H2SO4-activated carbon
may contribute to environmental sustainability and offer ben- (CSAC)
efits for future commercial applications. The costs of activated
carbon prepared from biomaterials are very low compared to Infrared spectra of the adsorbents were obtained using a Fou-
the cost of commercial activated carbon. Waste materials that rier transform infrared spectrometer (FTIR-2000, PerkinEl-
have been successfully used to manufacture activated carbon in mer). For the FT-IR study, finely ground adsorbent has been
the recent past include waste wood (Acharya et al., 2009), ba- intimately mixed with KBr (Merck) in a ratio of 1:100 in order
gasse (Tsai et al., 2001), coir pith (Namasivayam and Kavitha, to prepare a translucent pellet. From these FT-IR spectra the
2002), orange peel (Khaled et al., 2009), coffee husk (Ahmad presence of functional groups on the adsorbent were confirmed.
and Rahman, 2011), pine cone (Gecgel and Kolancilar, The surface morphology of the activated carbon particles was
2012), coconut tree (Senthilkumaar et al., 2006), sunflower analyzed using a scanning electron microscope (JEOL-JSM-
seed hull (Thinakaran et al., 2008), pine-fruit shell (Royer 6380 LA, Japan). The carbon particles were mounted on sample

Please cite this article in press as: Aljeboree, A.M. et al., Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell acti-
vated carbon. Arabian Journal of Chemistry (2014), http://dx.doi.org/10.1016/j.arabjc.2014.01.020
Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell activated carbon 3

S C 2H 5

GRL N N N
+
N CH2CH2 OH

- CH 3
CH3OSO3
NaO3 S

NaO 3S
HC CH N

DY 12

N
EtO N

OEt

Figure 1 Chemical structures of both dyes maxilon blue (GRL), and direct yellow (DY 12).

stubs and coated with gold foil using a gold-coating machine CSAC (particle size 75 lm) and 100 mL of dye concentration
(JEOL-JSM-420, Japan). The samples were then automatically (2–16) mg/L. The pH was adjusted using 0.1 N NaOH and
analyzed using computer software. 0.1 N HCl solutions by using an Orion 920A pH-meter with
a combined pH electrode. pH-meter was standardized with
2.4. Kinetic experiments NBS buffers before every measurement.

Adsorption kinetic experiments were carried out using shaker 2.5.3. Effect of solution temperature
water bath. All of the dye solution was prepared with distilled The effect of temperature to the adsorption capacity of CSAC
water. Kinetic experiments were carried out by agitating was carried out at 10, 20, 30, and 40 C in a constant temper-
100 ml of solution of a constant dye concentration with 50 mg ature bath at natural solution pH 6, 120 rpm 50 mg of CSAC
of CSAC at a constant agitation speed, 20 C and natural pH. (particle size 75 lm) and 100 mL of dye concentration
Agitation was made for 120 min, which is more than sufficient (2–16) mg/L.
time to reach equilibrium at a constant stirring speed of
120 rpm. Preliminary experiments had shown that the effect of 2.5.4. Effect of mass dosage
the separation time on the adsorbed amount of dye was negligi-
The effect of mass dosage was studied by agitating in different
ble. Two milliliters of samples was drawn at suitable time inter-
masses (0.005, 0.01, 0.05, and 0.5 g), at 20 C, 120 rpm, 50 mg
vals. The samples were then centrifuged for 15 min at 5000 rpm
of CSAC (particle size 75 lm) and 100 mL of (DY 12 or GRL)
and the left out concentration in the supernatant solution was
dye concentration (2–16) mg/L.
analysed using UV–vis spectrophotometer by monitoring the
absorbance changes at a wavelength of maximum absorbance
2.5.5. Effect of particle size
(599 and 403 nm for GRL and DY 12 respectively). Each exper-
iment continued until equilibrium conditions were reached when The effect of particle size to the adsorption capacity of CSAC
no further decrease in the dye concentration was measured. Cal- was carried out in (50, 75, and 106 lm), at 20 C, pH 6,
ibration curves were plotted between absorbance and concentra- 120 rpm, 50 mg of CSAC and 100 mL of dye concentration
tion of the dye solution. It was investigated the effects of the (2–16) mg/L.
following parameters to the removal rate of maxilon blue
GRL and direct yellow DY 12 dyes on CSAC in the experiments. 2.6. Data evaluation

2.5. Effect of different parameters of adsorption processes of Adsorption kinetics investigations were carried out by agitat-
GRL and DY 12 on CSAC ing 100 mL of GRL, and DY 12 dye solutions of known initial
concentration with 0.5 g/L of adsorbent at a known tempera-
2.5.1. Effect of initial dye concentration ture of 318 K, at pH of 6.0 ± 0.2 and at 120 rpm for different
time intervals. The amount of dye adsorbed onto the adsor-
The initial tested concentrations of dyes were 2, 4, 6, 8, 10, 12,
bent at equilibrium, qe (mg/g), was calculated by the following
14, and 16 mg/L for both dyes at different pH, temperature,
expression:
particle size, and mass dosage.
ðC0  Ce Þ  V
qe ¼ ð1Þ
2.5.2. Effect of pH w
The effect of pH on the rate of color removal was analyzed in where C0 and Ce are the initial and equilibrium dye concentra-
the pH range at 3, 6, 8 and 10 at 20 C, 120 rpm, 50 mg of tions in mg/L respectively, V is the volume of solution (L) and

Please cite this article in press as: Aljeboree, A.M. et al., Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell acti-
vated carbon. Arabian Journal of Chemistry (2014), http://dx.doi.org/10.1016/j.arabjc.2014.01.020
4 A.M. Aljeboree et al.

W is the mass of the CSAC adsorbent (g), the amount of (Cazetta et al., 2011). The presence of hydroxyl groups, carbonyl
adsorption at time t, qt (mg/g) was calculated by: group, ethers and aromatic compounds is an evidence of the lig-
ðC0  Ct Þ  V nocellulosic structure of coconut shell as also observed in other
qt ¼ ð2Þ materials such as Brazilian coconut shell (Cazetta et al., 2011),
w
and jackfruit peel waste (Prahas et al., 2008), (Fig. 2(b and c)
where C0 and Ct (mg/g) are the liquid phase concentrations of shows there is no real shift in our absorption peaks but the inten-
the dye at initial and any time t, respectively. V is the volume sity becomes higher after absorption, this is indicated as a
of solution (L) and W is the mass of the CSAC adsorbent (g). physical adsorption.
Scanning electron microscopy (SEM) has been a primary
3. Results and discussion tool for characterizing the surface morphology and fundamen-
tal physical properties of the adsorbent. SEM of adsorbent
3.1. Surface characterizations material was taken before and after dye adsorption on CSAC
(Fig. 3). From (Fig. 3a), it is clear, there is a good possibility
In order to detect the functionality present in CSAC prior to and for dyes to be trapped and adsorbed into these pores. The
after (GRL and DY 12) dyes adsorbed. Adsorption in the infra- SEM pictures of adsorbed samples show very distinguished
red (IR) region takes place (4000–400 cm1) due to the rota- dark spots which can be taken as a sign for effective adsorption
tional and vibrational movement of the molecular groups and of dye molecules in the cavities and pores of this adsorbent. The
chemical bond of a molecule. The FT-IR spectra were obtained micrographs presented in (Figs. 3b and c) show clearly the dye-
to evaluate qualitatively the chemical structures of CSAC. loaded adsorbent coated by dye molecules over the whole sur-
(Fig. 2(a)) shows the FT-IR spectrum of CSAC, which indicated face at natural pH conditions. The dye molecules seem to have
various surface functional groups. The broadband at around formed a void-free film masking the reliefs of particles and
3500 cm1 is typically attributed to hydroxyl groups. The region porosity of the aggregates (Kismir and Aroguz, 2011).
of the spectrum of 2220 cm1 is attributed to alkyne group
(C„C). The region of the spectrum of 1612 cm1 is attributed 3.2. Adsorption kinetics modeling
to axial deformation of carbonyl groups (C‚O)
Study of adsorption kinetics is important because the rate of
adsorption (which is one of the criteria for efficiency of adsor-
bent) and also the mechanism of adsorption can be concluded
CSAC from kinetic studies. Fig. 4 shows the variation of the amount
89.6 (a) of adsorbed (qt) as a function of time. The rate of adsorption
for both dyes is high at initial times of adsorption. For both
86.4 dyes most of adsorption takes place within 10 min which indi-
T%

cate that the rate of dye adsorption by CSAC is high.

In order to analyze the adsorption kinetics of GRL and DY
83.2 12 by CSAC the pseudo-first order (Lagergren, 1898), pseudo-
1612 second order (Ho and McKay, 1999), Elovich equation (Low,
80.0 3500 2200 1960), and intra-particle diffusion (Weber and Morris, 1963),
DY12/CSAC were tested. The result of fitting is listed in Table 1. A simple
(b) kinetic analysis of adsorption (pseudo-first-order equation) is
88
in the form:
qt ¼ qe ½1  expðkf tÞ ð3Þ
77
T%

where qt is the amount of adsorbate adsorbed at time t

66 1612 (mg g1), qe is the adsorption capacity in the equilibrium
2200 (mg g1), kf is the pseudo-first-order rate constant (min1),
3500 and t is the contact time (min).
55
GRL/CSAC A pseudo-second-order equation based on adsorption equi-
62.7 (c) librium capacity may be expressed in the form:
ks q2e t
59.4 qt ¼ ð4Þ
1 þ ks qe t
where Ks is the the pseudo-first-order rate constant (g gm1 -
T%

56.1 min1), the initial sorption rate (ho, expressed in mg g1 min1)
can be obtained when t approaches to zero, Eq. (5)
52.8
2200 1612 h0 ¼ ks q2e ð5Þ
4000 3500 3000 2500 2000 1500 1000 500 The Elovich equation used for general application to
cm
-1 chemisorption. The equation has been applied satisfactorily
to some chemisorption processes and has been found to cover
Figure 2 FT-IR spectra of (a) CSAC derived from coconut shell a wide range of slow adsorption rates. The same equation is
(b) DY 12 adsorbed on the surface of CSAC, and (c) GRL often valid for systems in which the adsorbing surface is
adsorbed on the surface of CSAC. heterogeneous, and is formulated as:

Please cite this article in press as: Aljeboree, A.M. et al., Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell acti-
vated carbon. Arabian Journal of Chemistry (2014), http://dx.doi.org/10.1016/j.arabjc.2014.01.020
Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell activated carbon 5

14 (a)
12

10

-1
8

qt/ mg.g
6 Experimental
Pseudo-first order
4 Pseudo-second order
Chemisorption
2 Intra-particle diffusion

0
0 10 20 30 40 50 60
Time/min

3.0 (b)
2.5

2.0

-1
qt/mg.g
1.5

1.0 Experimental
Pseudo-first order
Pseudo-second order
0.5
Chemisorption
Intra-particle diffusion
0.0
0 10 20 30 40 50 60
Time/min

Figure 4 Adsorption rate curves (a) GRL dye, and (b) DY 12

dye: experimental conditions: pH 6, dye conc. 10 mg/L, particle
size 75 lm, Temp. 293 K and mass catalyst 0.05 g).

tration of 10.0 mg/L. Fig. 4 indicates that while the adsorption

of dyes was quite rapid initially, the rate of adsorption became
slower with the time and reached a constant value (equilibrium
time). The initial faster rate may be due to the availability of
the uncovered surface area of the adsorbents. (Kilic et al.,
2011; Shi et al., 2013).
All the experimental data showed better compliance with
Figure 3 Scanning electron micrographs (SEM): (a) CSAC chemisorptions kinetic model for GRL and DY 12 in terms
before adsorption process, (b) CSAC adsorbed with GRL and (c) of higher correlation coefficient values R2 > 0.989. Moreover,
CSAC adsorbed with DY 12. the q values calculated (qe,cal) from pseudo first-order model
were more consistent with the experimental q values (qe,exp)
    than those calculated from the pseudo second-order model.
1 1
qt ¼ lnð/ :bÞ þ lnðtÞ ð6Þ
b b 3.3. Effect of different parameters of adsorption processes of
The intra-particle diffusion model based on the theory pro- GRL and DY 12 on CSAC
posed by Weber and Morris (Weber and Morris, 1963) was used
to identify the diffusion mechanism. According to this theory, 3.3.1. Effect of pH
the adsorbate uptake qt varies almost proportionally with the The effect pH was investigated on the adsorption of GRL and
square root of the contact time, t½ rather than t, Eq.(7). DY 12 on CSAC at a pH of 3–10 for 2 h. The result in Fig. 5
pffiffi showed that maximum adsorption of GRL, and DY 12 was
qt ¼ kid t þ I ð7Þ
obtained at the lowest pH 3 while the lowest adsorption was
where I is the intercept and Kid (mg g1 min1/2) is the intra- at pH 10.
particle diffusion rate constant. As the pH of the solution increases, adsorption of both dyes
Fig. 4 represents the variation of dye adsorption on CSAC GRL and DY 12 was found to be decreasing; this was due to the
with shaking time (0–60 min) and initial dye solution concen- extinction of the positive hydrogen ions thereby promoting

Please cite this article in press as: Aljeboree, A.M. et al., Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell acti-
vated carbon. Arabian Journal of Chemistry (2014), http://dx.doi.org/10.1016/j.arabjc.2014.01.020
6 A.M. Aljeboree et al.

(a)
(a)
pH3 0.5g
pH6 0.05g 20
pH8 25 0.01g
pH10 0.005g
20 15

qe/ mg.g -1

qe/mg.g -1
15 10

10
5
5
16 0
16 0 0.
00
pH 12 5g
12 10
0.0

C0
pH 8 1g

/m
8 8
C0

0.

g.
/m

4 05

L
-1
pH g
g.
-1
L

4 6
0.
0 5g
pH
0 3

(b)
0.5g
(b)
0.05g
70
pH3 8
pH6 0.01g
0.005g 60
pH8
pH10 50
6

qe/mg.g -1
40
qe/ mg.g -1

4 30

20

2 10

16 0
0.
00
16 0 12 5g
pH 0.
10 01
12 8
C0

g
/m

pH 0.
g.

05
L

8
-1

8
C0

4 g
/m

pH 0.
g.

5g
L
-1

4 6 0
pH
0 3
Figure 6 Effect of mass adsorbent on adsorption (a) GRL, and
(b) DY 12 experimental conditions: Temp. 293 K, pH 6, and
Figure 5 Effect of solution pH on adsorption (a) GRL, and (b)
particle size 75 lm.
DY 12 experimental conditions: Temp. 293 K, CSAC dosage
50 mg/L, and particle size 75 lm. adsorption density, the amount adsorbed per unit mass,
decreases. It is readily understood that the number of available
activities of electrostatic repulsion between the negative charges adsorption sites increases by increasing the adsorbent dose and
of both dye and the CSAC surface (Auta and Hameed, 2011). it, therefore, results in an increase of the amount of adsorbed
While at an acidic pH, the functional groups of activated carbon dye (Hameed et al., 2013). The decrease in adsorption density
become protonated, which are mainly the carboxylic groups with an increase in the adsorbent dose is mainly because of
(COOHþ þ
2 ), phenolic (ðOH2 Þ) and chromenic group (Al- adsorption sites remain unsaturated during the adsorption
Degs et al., 2008). At pH 3, the surface charge of CSAC becomes reaction whereas the number of sites available for adsorption
more positively charged, which enhances (GRL and DY 12) site increases by increasing the adsorbent dose (Malik et al.,
adsorption through electrostatic attraction. 2007; Yener et al., 2006) .

3.3.2. Effect of adsorbent dose 3.3.3. Effect of particle size

Fig. 6 shows the adsorption of both dyes GRL and DY 12 as a Particle size of an adsorbent played a very important role in the
function of adsorbent dosage. It is apparent that by increasing adsorption capacity of dye. The relationship of adsorption
the adsorbent dose the amount of adsorbed dye increases but capacity to particle size depends on two criteria: (i) the chemical

Please cite this article in press as: Aljeboree, A.M. et al., Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell acti-
vated carbon. Arabian Journal of Chemistry (2014), http://dx.doi.org/10.1016/j.arabjc.2014.01.020
Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell activated carbon 7

Table 1 Pseudo first-order, pseudo second-order, chemisorption and intraparticle diffusion model constants and correlation
coefficients for (GRL and DY 12 dyes) adsorption onto CSAC.
Kinetic model Dye Parameters Value Standard error R2
1
Pseudo-first order GRL kf (min ) 0.13088 0.00934 0.99233
qe (mg g1) 13.19959 0.21266
DY 12 kf (min1) 0.06179 0.00908 0.97437
qe (mg g1) 2.73303 0.1311
Pseudo-second order GRL ks (g mg1 min1) 0.01113 0.00066 0.99304
qe (mg g1) 15.07327 0.19122
h0 (mg g1 min1) 2.52877 -
DY 12 ks (g mg1 min1) 0.01837 0.00283 0.97400
qe (mg g1) 3.43605 0.18306
h0 (mg g1 min1) 0.21688 -
Chemisorption GRL a (mg g1 min1) 7.74641 0.70563 0.98955
b (g min1) 0.3616 0.028329
DY 12 a (mg g1 min1) 0.48945 0.1231 0.99057
b (g min1) 1.34518 0.06879
Intra-particle diffusion GRL kid (mg g1 min0.5) 1.68632 0.24566 0.86823
DY 12 kid (mg g1 min0.5) 0.36053 0.01328 0.99058

structure of the dye molecule (its ionic charge) and its chemistry parameters such as Gibbs free energy change (DG), enthalpy
(its ability to formhydrolyzed species) and (ii) the intrinsic (DH), and entropy (DS) were calculated using the following
characteristic of the adsorbent (its crystallinity, porosity and equations:
rigidity of the polymericchains) (Iqbal et al., 2011). Fig. 7 shows
DG0 ¼ RTlnK0 ð8Þ
the effect of particle size on textile dye adsorption.
Fig. 7 shows Minimum particle size showed greater adsorp- where k0 is the apparent equilibrium constant, R is the gas con-
tion than larger size. Small size of adsorbent increases the sur- stant (8.314 J/(molK)), and T is absolute temperatures (K).
face area for adsorption. The increase in adsorption capacity The apparent enthalpy (DH) of adsorption and entropy
with decreasing particle size suggests that the dye preferentially (DS) of adsorption were calculated from adsorption data at
adsorbed on the outer surface and did not fully penetrate the different temperatures using the Van’t Hoff Eq. (9) as follows:
particle due to steric hindrance of large dye molecules DH DS
(Gouamid et al., 2013; Li et al., 2011; Rehman et al., 2013). lnK0 ¼ þ ð9Þ
RT R
3.3.4. Effect of temperature The values of ln K0 for thermodynamic calculations were ob-
The effect of temperature on the adsorption of both dyes tained from equilibrium constant (Ks) for the adsorption as
(GRL and DY 12) by CSAC was studied within the tempera- follows (Li et al., 2010):
tures (10, 20, 30 and 40 C) on adsorption at (2–16 mg/L) q v1
Ks ¼ e  ð10Þ
initial dye concentration, pH 6, results are shown in Fig. 8. Ce v2
It was observed that the adsorption capacity of GRL on
where m1 is the activity coefficient of the adsorbed solute, and m2
CSAC (Fig. 8a) was higher than that of DY 12 (Fig. 8b). This
is the activity coefficient of the solute in equilibrium suspension.
results may be ascribed to the vacant sites on AC used for
The ratio of activity coefficients was assumed to be uniform in
adsorption were constant, and the molecular weight of GRL
the dilute range of the solutions. As the concentration of the
was higher than that of DY 12. Meanwhile, with the initial
dye in the solution approached zero, the activity coefficient ap-
temperatures of dye solution increased from 10 to 40 C, the
proached unity Eq. (11)
adsorption capacities of GRL and DY 12 decreased this may
causes an increase in the solubility of the dyes, resulted in a q
lim e ¼ K0 ð11Þ
Ce !0 Ce
stronger interaction forces between dyes and solvent than
those between dyes and CSAC (Dotto et al., 2012; Zhou The values of K0 determined from the intercept (figure not
et al., 2011; Zhou et al., 2014). A decrease in the adsorption shown), by plotting ln qe/Ce versus Ce and extrapolating to
of both dyes GRL and DY 12 with increasing temperature is Ce = 0 (Gupta et al., 2004). All the calculated thermodynamic
related to the increasing Brownian movement of molecules in parameters are presented in Table 2.
solution (Li et al., 2013). High temperature might also lead For the adsorption of both GRL and DY 12 dyes on
to the breaking of existing intermolecular hydrogen bonding CSAC, the obtained DH values were negative, which indicated
between GRL and DY 12 and CSAC, which is an important the exothermic nature of both dye adsorption onto CSAC. The
contribution to the adsorption process (Li et al., 2013). change in entropy was positive, indicating the entropy of the
system increased during the adsorption. However, it should
3.4. Thermodynamic study also be noted that the entropy of the universe (including the
system and the surroundings) might increase because the
The thermodynamic behaviors for adsorption of GRL and DY adsorption reaction was not an isolated process. The negative
12 on CSAC were further investigated. The thermodynamic values of DG for both dyes demonstrated that the adsorption

Please cite this article in press as: Aljeboree, A.M. et al., Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell acti-
vated carbon. Arabian Journal of Chemistry (2014), http://dx.doi.org/10.1016/j.arabjc.2014.01.020
8 A.M. Aljeboree et al.

106 µm 283K
30 25
(a) 75 µm 293K
50 µm 303K
25 313K
20
20

qe/mg.g -1
15

qe/mg.g -1
15
(a)
10 10

5
5
16 0
50 16 0
12 um
31
12 3K
8
C0

75
30
/m

um
3K
g.

C0
L
-1

/m
29

g.
10 3K

L
-1
6u 4
0 m
28
0 3K

(b)
106um
(b) 75um
6
50um 283K
5 293K 5
303K
4 313K
qe /mg.g -1

4
3

qe/mg.g -1
3
2

1 2

16 0 1
50
12 um
16 0
8
C0

75 31
/m

um
12 3K
g.
L
-1

4
30
10 8 3K
C0

6u
/m

0 m 29
g.

3K
L
-1

4
Figure 7 Effect of particle size on adsorption (a) GRL, and (b) 28
0 3K
DY 12 experimental conditions: Temp. 293 K, mass dosage 50 mg/
L, and pH 6.
Figure 8 Effect of temperature on adsorption (a) GRL, and (b)
DY 12: experimental conditions: particle size 75 lm, CSAC
dosage 50 mg/L, and pH 6.
process on CSAC was a spontaneous process, and the decrease
of DG values with the increase of temperature indicated that
the adsorption became less favorable at higher temperatures Temkin and Fritz–Schlunder (F–S) models were applied to fit
(Zhou et al., 2014). the equilibrium data. Each isotherm model was expressed by
relative certain constants which characterized the surface prop-
3.5. Determination of adsorption isotherm parameters erties and indicated adsorption capacity of this material.

The adsorption isotherm can describe the distribution of dye 3.5.1. Langmuir isotherm
between solid phase and the solution at a certain temperature The Langmuir model proposes that monolayer sorption occurs
when the equilibrium was reached. The Langmuir, Freundlich, on the solid surface with identical homogeneous sites

Please cite this article in press as: Aljeboree, A.M. et al., Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell acti-
vated carbon. Arabian Journal of Chemistry (2014), http://dx.doi.org/10.1016/j.arabjc.2014.01.020
Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell activated carbon 9

Table 2 Thermodynamic functions DG, DS and, DH of GRL and DY 12 adsorbed on the CSAC.
T/K Ke DG/kJ mol1 DH/kJ mol1 DS/J.K1 mol1
CSAC adsorbent/GRL adsorbate
283 7.01126 4.58224 3.966277 2.110093
293 6.46867 4.54794
303 6.25687 4.6193
313 5.92734 4.63096
CSAC adsorbent/DY 12 adsorbate
283 9.15672 5.21038 2.14019 10.84927
293 8.85693 5.31341
303 8.6671 5.44017
313 8.37077 5.52919

(Langmuir, 1918). It also suggests that no further adsorption equilibrium binding constant related to the maximum binding
takes place once the active sites are covered with dye mole- energy (L/mg).
cules. The saturated monolayer isotherm is presented by the
following equation: 3.5.4. Fritz–Schlunder (F–S) isotherm
qm KL Ce The F–S model is empirical three-parameter isotherm combin-
qe ¼ ð12Þ ing the Langmuir and Freundlich isotherms (Fritz and
1 þ KL Ce
Schlunder, 1974). It is based on the following equation:
where Ce is the concentration of dye at equilibrium in solution
KFS qm Ce
(mg/L); qe is unit equilibrium adsorption capacity; qm is the qe ¼ ð15Þ
1 þ qm Cne
maximum dye uptake, giving the information about
adsorption capacity for a complete monolayer (mg/g); and where KFS is the Fritz–Schlunder model constant (L/mg), qm the
KL is a constant denoted the energy of adsorption and affinity amount of dye adsorbed (mg/g) when the saturation is attained,
of the binding sites (L/mg). and n is the Freundlich constant (Batzias and Sidiras, 2007).
The coefficients of determination (R2) and isotherm param-
3.5.2. Freundlich isotherm eters from nonlinear regressive method were listed in Table 3.
Freundlich isotherm is an empirical model assuming that the A comparison of nonlinear fitted curves from experimental
distribution of the heat on the adsorbent surface is nonuni- data and four different isotherms at 283, 293, 303 and 313 K
form, namely a heterogeneous adsorption (Freundlich and is shown in Fig. 9.
Heller, 1939). The equation is stated as follows: The Langmuir adsorption model was found to fit the exper-
imental data for both dyes sufficiently in accordance with the
qe ¼ Kf C1=n
e ð13Þ liner correlation coefficients (R2). The larger values of R2
n
where n and KF [mg/g (L/mg) ] are both the Freundlich con- (P0.9867) indicted the applicability of the Langmuir isotherm
stants giving an indication of adsorption intensity and capac- for dye adsorption. qm was an important Langmuir constant,
ity, respectively. The degree of non-linearity between solution representing the maximum capacity at equilibrium. The differ-
concentration and adsorption is n dependent as follows: if ence of KL values between CSAC/GRL and CSAC/DY 12 re-
the value of n is equal to unity, the adsorption is linear; if fers to the different in binding strength and capacity of the
the value is below to unity, this implies that adsorption process dyes with the surface of the CSAC, in general values of KL de-
is chemical; if the value is above unity adsorption is a favorable creased with the rise of temperature.
physical process (Kumar et al., 2010). The Freundlich model did not provide any information
about the saturation adsorption capacity as well as Langmuir
model with lower R2 (0.9552). The parameters of KF and 1/n
3.5.3. Temkin isotherm exhibited intense change at higher temperatures. The values
The Temkin model proposes into account the effects of the inter- of 1/n (0.1 < 1/n < 1) indicated favorable adsorption of both
action of the adsorbate and the adsorbing species (Tempkin and dyes at experimental conditions. The Temkin model provides
Pyzhev, 1940). By ignoring the extremely low and large concen- calculation of equilibrium binding constant corresponding to
tration values, the model assumes that the heat of adsorption (a the maximum binding energy, KT, decreased as the experimen-
function of temperature) of all of the molecules in the layer tal temperature increased from 283 to 313 K, which implies
would decrease linearly rather than logarithmically with cover- that the adsorption process is exothermic and favored at high-
age due to adsorbate–adsorbent interactions (Aharoni and er temperatures. Moreover, it was observed from Fig. 9 that
Ungarish, 1977), the equation is stated as follows: the fitted curves from the F–S isotherm were most near to
the experimental data at experimental conditions. Hence, the
RT
qe ¼ logðKT Ce Þ ð14Þ (F–S) model was best to describe adsorption behavior at equi-
b librium. By comparing the four models, it seems that the model
where b Tempkin constant related to the heat of adsorption of Fritz–Schlunder is the most adapted for the fitting of
(kJ/mol), and KT empirical Tempkin constant related to the adsorption isotherms, then Langmuir model more adapted

Please cite this article in press as: Aljeboree, A.M. et al., Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell acti-
vated carbon. Arabian Journal of Chemistry (2014), http://dx.doi.org/10.1016/j.arabjc.2014.01.020
 10
vated carbon. Arabian Journal of Chemistry (2014), http://dx.doi.org/10.1016/j.arabjc.2014.01.020
Please cite this article in press as: Aljeboree, A.M. et al., Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell acti-

Table 3 Parameters for different parameters isotherm models for the adsorption study of GRL, and DY 12 dyes onto CSAC at different temperatures.
Isotherm models Parameters GRL dye DY 12 dye
Temperature/K Temperature/K
283 293 303 313 283 293 303 313
Langmuir qm (mg.g1) 51.55973 ± 4.6333 62.0622 ± 7.3265 58.2523 ± 5.4931 58.51038 ± 7.2047 9.9275 ± 0.6114 13.7752 ± 1.2896 10.0211 ± 0.4543 12.6067 ± 2.6766
KL(L.mg1) 0.21508 ± 0.0304 0.12128 ± 0.02008 0.10311 ± 0.0136 0.08209 ± 0.0138 0.1338 ± 0.0170 0.0496 ± 0.0068 0.0694 ± 0.0052 0.0356 ± 0.0103
R2 0.9933 0.99449 0.99665 0.99518 0.98923 0.99544 0.99792 0.9867
Freundlich KF 9.13054 ± 0.5222 6.92385 ± 0.39591 5.74431 ± 0.2924 4.70083 ± 0.3218 1.5380 ± 0.1936 0.8089 ± 0.0741 0.8414 ± 0.0747 0.5120 ± 0.0762
1/n 0.71021 ± 0.0521 0.77417 ± 0.04539 0.77352 ± 0.0363 0.79674 ± 0.0449 0.56417 ± 0.05781 0.7469 ± 0.0403 0.6824 ± 0.0390 0.8052 ± 0.0638
R2 0.97679 0.98592 0.99115 0.98701 0.95521 0.98817 0.98633 0.97579
Tempkin b/J.mole1 2.9939 ± 0.2822 2.44113 ± 0.3910 2.16876 ± 0.361 1.67253 ± 0.2210 2.2226 ± 0.0960 2.1375 ± 0.1621 1.8524 ± 0.1042 1.7605 ± 0.1172
KT 9.13003 ± 0.5028 8.50254 ± 0.7920 7.79026 ± 0.7390 7.80985 ± 0.6289 1.2665 ± 0.1138 0.8337 ± 0.1110 0.9088 ± 0.0946 0.6708 ± 0.0718
R2 0.97915 0.94227 0.94023 0.95631 0.98709 0.96109 0.97825 0.96979
Fritz–Schlunder qm 33.6805 ± 1.6735 40.48221 ± 6.4421 46.56237 ± 10.8049 33.70863 ± 3.0998 7.69475 ± 0.4405 10.58464 ± 2.2019 8.02541 ± 0.5816 6.01633 ± 0.6502
KFS 0.35858 ± 0.0247 0.1864 ± 0.0321 0.12808 ± 0.0304 0.13194 ± 0.0108 0.12999 ± 0.0104 0.05699 ± 0.0074 0.07556 ± 0.0035 0.04245 ± 0.0050
m 1.33488 ± 0.0615 1.21833 ± 0.1149 1.08918 ± 0.1064 1.28034 ± 0.0744 1.34307 ± 0.1093 1.12811 ± 0.1235 1.14701 ± 0.0586 1.48367 ± 0.1420
R2 0.99892 0.99624 0.99649 0.99856 0.99589 0.99554 0.99891 0.99565

A.M. Aljeboree et al.

Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell activated carbon 11

(a)
6 6 293 K
283 K

-1

-1
4 4

qe/ mg.g

qe/ mg.g
Experimental
Langmuir model
2 Freundlich model 2
Temkin model
Fritz–Schlunder model
0 0
0 3 6 9 12 15 0 3 6 9 12 15
-1 -1
6 Ce/ mg.L 6 Ce/ mg.L
303 K 313 K
4 4
-1

-1
qe/ mg.g

qe/ mg.g
2 2

0 0
0 3 6 9 12 15 0 3 6 9 12 15
-1 -1
Ce/ mg.L Ce/ mg.L

28 28 (b)
283 K 293 K
21 21
-1

-1
qe/mg.g

Experimental
qe/mg.g

14 14
Langmuir model
Freundlich model
7 7
Temkin model
Fritz–Schlunder model
0 0
0.0 3.5 7.0 0.0 3.5 7.0
-1
28 Ce/ mg.L 28 -1
Ce/ mg.L
303 K 313 K
21 21
-1

-1
qe/mg.g

qe/mg.g

14 14

7 7

0
0.0 3.5 7.0 0.0 3.5 7.0
-1
Ce/ mg.L Ce/ mg.L
-1

Figure 9 Adsorption isotherm models fitted to experimental adsorption of (a) DY 12, and (b) GRL (pH 6, Temp. 298, particle size
75 lm, mass dosage 50 mg/L).

than Temkin and Fruendlich models. The calculated parame- of these dyes on CSAC were studied and modeled using fourth
ters of fourth models are illustrated in Table 3. isotherm models with more than two-parameter. An excellent
prediction in all the studied concentration ranges can be ob-
4. Conclusion tained by the three-parameter equation (Fritz–Schlunder).
The classification of the models according to the simulation
Coconut shell, a food solid waste, was successfully utilized as a of the adsorption isotherms is: Fritz–Schlunder > Lang-
low cost alternative adsorbent for the removal of hazardous muir > Freundlich > Tempkin. Thermodynamic study dem-
textile dyes (GRL and DY 12). The shifting of peaks in FTIR onstrates the spontaneous and exothermic nature of
spectrum confirmed the GRL and DY 12 dye adsorption onto adsorption process due to negative values of both free energy
CSAC. The SEM study also made support to it by observing change and enthalpy change.
difference in surface morphology of adsorbent before and after
adsorption of GRL and DY 12. Kinetics adsorption models of
both GRL and DY 12 dyes on CSAC were studied and mod- Acknowledgments
eled using fourth kinetic models. The classification of the ki-
netic models according to the simulation of the adsorption The authors acknowledges to Ministry of Higher Education
study is: Chemisorption > Psuedo-second order > pseudo- and Scientific Research, Babylon University/College of
first order > Intra-particle-diffuse. Also adsorption isotherms Sciecne, Department of Chemistry, Iraq.

Please cite this article in press as: Aljeboree, A.M. et al., Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell acti-
vated carbon. Arabian Journal of Chemistry (2014), http://dx.doi.org/10.1016/j.arabjc.2014.01.020
12 A.M. Aljeboree et al.

References Gupta, V.K., Singh, P., Rahman, N., 2004. Adsorption behavior of
Hg(II), Pb(II), and Cd(II) from aqueous solution on Duolite C-433:
Acharya, J., Sahu, J.N., Sahoo, B.K., Mohanty, C.R., Meikap, B.C., a synthetic resin. J. Colloid Interf. Sci. 275, 398–402.
2009. Removal of chromium(VI) from wastewater by activated Hajati, S., Ghaedi, M., Karimi, F., Barazesh, B., Sahraei, R.,
carbon developed from Tamarind wood activated with zinc Daneshfar, A., 2014. Competitive adsorption of direct yellow 12
chloride. Chem. Eng. J. 150, 25–39. and reactive o12 on ZnS:Mn nanoparticles loaded on activated
Aharoni, C., Ungarish, M., 1977. Kinetics of activated chemisorption. Part carbon as novel adsorbent. J. Ind. Eng. Chem. 20, 564–571.
2. Theoretical models. J. Chem. Soc., Faraday Trans. 73, 456–464. Hameed, K.S., Muthirulan, P., Meenakshi, S.M., 2013. Adsorption of
Ahmad, M.A., Rahman, N.K., 2011. Equilibrium, kinetics and chromotrope dye onto activated carbons obtained from the seeds of
thermodynamic of Remazol Brilliant Orange 3R dye adsorption various plants: Equilibrium and kinetics studies. Arabian J. Chem,
on coffee husk-based activated carbon. Chem. Eng. J. 170, 154–161. http://dx.doi.org/10.1016/j.arabjc.2013.07.058.
Al-Degs, Y.S., El-Barghouthi, M.I., El-Sheikh, A.H., Walker, G.M., Ho, Y.S., McKay, G., 1999. Pseudo-second order model for sorption
2008. Effect of solution pH, ionic strength, and temperature on processes. Process Biochem. 34, 451–465.
adsorption behavior of reactive dyes on activated carbon. Dyes Iqbal, M.J., Ashiq, M.N., 2007. Adsorption of dyes from aqueous
Pigments 77, 16–23. solutions on activated charcoal. J. Hazard. Mater. 139, 57–66.
AlOthman, Z.A., Habila, M.A., Ali, R., Abdel, A., 2013. Ghafar, M.S. El- Iqbal, J., Wattoo, F.H., Wattoo, M.S., Malik, R., Tirmizi, S.A.,
din Hassouna, Valorization of two waste streams into activated Imran, M., Ghangro, A.B., 2011. Adsorption of acid yellow dye on
carbon and studying its adsorption kinetics equilibrium isotherms and flakes of chitosan prepared from fishery wastes. Arabian J. Chem.
thermodynamics for methylene blue removal. Arabian Journal of 4, 389–395.
Chemistry 2, 2–12, http://dx.doi.org/10.1016/j.arabjc.2013.05.007. Khaled, A., El Nemr, A., Ei-Sikaily, A., Abdelwahab, A., 2009.
Auta, M., Hameed, B.H., 2011. Optimized waste tea activated carbon Treatment of artificial textile dye effluent containing direct yellow
for adsorption of methylene blue and acid blue 29 dyes using 12 by orange peel carbon. Desalination 238, 210–232.
response surface methodology. Chem. Eng. J. 175, 233–243. Kilic, M., Apaydin-Varol, E., Putun, E.A., 2011. Adsorptive removal
Banerjee, S., Chattopadhyaya, M.C., 2013. Adsorption characteristics of phenol from aqueous solutions on activated carbon prepared
for the removal of a toxic dye tartrazine from aqueous solutions by from tobacco residues: Equilibrium, kinetics and thermodynamics.
a low cost agricultural by-product. Arabian Journal of Chemistry, J. Hazard. Mater. 189, 397–403.
http://dx.doi.org/10.1016/j.arabjc.2013.06.005. Kismir, Y., Aroguz, A.Z., 2011. Adsorption characteristics of the hazardous
Batzias, F.A., Sidiras, D.K., 2007. Simulation of dye adsorption by dye brilliant green on Saklikent mud. Chem. Eng. J. 172, 199–206.
beech sawdust as affected by pH. J. Hazard. Mater. 141, 668–679. Konicki, W., Sibera, D., Mijowska, E., Lendzion-Bielun, Z., Nar-
Cazetta, A.L., Vargas, A.M., Nogami, E.M., Kunita, M.H., Guilher- kiewicz, U., 2013. Equilibrium and kinetic studies on acid dye acid
me, M.R., Martins, A.C., Silva, T.L., Moraes, J.G., Almeida, V.C., red 88 adsorption by magnetic ZnFe2O4 spinel ferrite nanoparti-
2011. NaOH-activated carbon of high surface area produced from cles. J. Colloid Interf. Sci. 398, 152–160.
coconut shell: Kinetics and equilibrium studies from the methylene Kumar, P.S., Ramalingam, S., Senthamarai, C., Niranjanaa, M.,
blue adsorption. Chem. Eng. J. 174, 117–125. Vijayalakshmi, P., Sivanesan, S., 2010. Adsorption of dye from
Chiou, M., Chuang, G., 2006. Competitive adsorption of dye metanil aqueous solution by cashew nut shell: studies on equilibrium isotherm,
yellow and RB15 in acid solutions on chemically cross-linked kinetics and thermodynamics of interactions. Desalination 261, 52–60.
chitosan beads. Chemosphere. 62, 731–740. Lagergren, S., 1898. About the theory of so-called adsorption of
Demirbas, E., Kobya, M., Sulak, M.T., 2008. Adsorption kinetics of a soluble substances. Kungliga Suensk Vetenskapsakademiens Hand-
basic dye from aqueous solutions onto apricot stone activated lingar 241, 1–39.
carbon. Bioresour. Technol. 99, 5368–5373. Langmuir, I., 1918. Adsorption of gases on plain surfaces of glass mica
Dotto, G.L., Lima, E.C., Pinto, L.A., 2012. Biosorption of food dyes platinum. J. Am. Chem. Soc. 40, 1361–1403.
onto Spirulina platensis nanoparticles: Equilibrium isotherm and Li, Q., Yue, Q., Su, Y., Gao, B., Sun, H., 2010. Equilibrium,
thermodynamic analysis. Bioresour. Technol. 103, 123–130. thermodynamics and process design to minimize adsorbent amount
Foo, K.Y., Hameed, B.H., 2012. Coconut husk derived activated for the adsorption of acid dyes onto cationic polymer-loaded
carbon via microwave induced activation: Effects of activation bentonite. Chem. Eng. J. 158, 489–497.
agents, preparation parameters and adsorption performance. Li, W., Yue, Q., Tu, P., Ma, Z., Gao, B., Li, J., Xu, X., 2011. Adsorption
Chem. Eng. J. 184, 57–65. characteristics of dyes in columns of activated carbon prepared from
Freundlich, H., Heller, W., 1939. The adsorption of cis- and trans- paper mill sewage sludge. Chem. Eng. J. 178, 197–203.
azobenzene. J. Am. Chem. Soc. 61, 2228–2230. Li, H., Huang, G., An, C., Hu, J., Yang, S., 2013. Removal of tannin
Fritz, W., Schlunder, E.U., 1974. Simultaneous adsorption equilibria from aqueous solution by adsorption onto treated coal fly ash:
of organic solutes in dilute aqueous solutions on activated carbon. kinetic, equilibrium, and thermodynamic studies. Ind. Eeg. Chem.
Chem. Eng. Sci. 29, 1279–1282. Res. 52, 15923–15931.
Gecgel, U., Kolancilar, H., 2012. Adsorption of Remazol brilliant blue Low, M.D., 1960. Kinetics of chemisorption of gases on solids. Chem.
R on activated carbon prepared from a pine cone. Nat. Prod. Res. Rev. 60, 267–312.
26, 659–664. Malik, R., Ramteke, D.S., Wate, S.R., 2007. Adsorption of malachite
Ghaedi, M., Sadeghian, B., Pebdani, A.A., Sahraei, R., Daneshfar, A., green on groundnut shell waste based powdered activated carbon.
Duran, C., 2012. Kinetics, thermodynamics and equilibrium Waste Manage. 27, 1129–1138.
evaluation of direct yellow 12 removal by adsorption onto silver Namasivayam, C., Kavitha, D., 2002. Removal of Congo red from
nanoparticles loaded activated carbon. Chem. Eng. J. 187, 133–141. water by adsorption onto activated carbon prepared from coir pith,
Ghaedi, M., Ansari, A., Sahraei, R., 2013. ZnS:Cu nanoparticles an agricultural solid waste. Dyes Pigments 54, 47–58.
loaded on activated carbon as novel adsorbent for kinetic, Prahas, D., Kartika, Y., Indraswati, N., Ismadji, S., 2008. Activated
thermodynamic and isotherm studies of reactive orange 12 and carbon from jackfruit peel waste by H3PO4 chemical activation:
direct yellow 12 adsorption. Spectrochim Acta A Mol. Biomol. pore structure and surface chemistry characterization. Chem. Eng.
Spectrosc. 114, 687–694. J. 140, 32–42.
Gouamid, M., Ouahrani, M.R., Bensaci, M.B., 2013. Adsorption equilib- Rehman, M.S., Munir, M., Ashfaq, M., Rashid, N., Nazar, M.F.,
rium, kinetics and thermodynamics of methylene blue from aqueous Danish, M., Han, J., 2013. Adsorption of brilliant green dye from
solutions using date palm leaves. Energy Procedia 36, 898–907. aqueous solution onto red clay. Chem. Eng. J. 228, 54–62.

Please cite this article in press as: Aljeboree, A.M. et al., Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell acti-
vated carbon. Arabian Journal of Chemistry (2014), http://dx.doi.org/10.1016/j.arabjc.2014.01.020
Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell activated carbon 13

Royer, B., Cardoso, N.F., Lima, E.C., Vaghetti, J.P., Simon, N.M., Tsai, W.T., Chang, C.Y., Lin, M.C., Chien, S.F., Sun, H.F., Hsieh,
Calvete, T., Veses, R.C., 2009. Applications of Brazilian pine-fruit M.F., 2001. Adsorption of acid dye onto activated carbons
shell in natural and carbonized forms as adsorbents to removal of prepared from agricultural waste bagasse by ZnCl2 activation.
methylene blue from aqueous solutions: kinetic and equilibrium Chemosphere 45, 51–58.
study. J. Hazard. Mater. 164, 1213–1222. Visa, M., Bogatu, C., Duta, A., 2010. Simultaneous adsorption of dyes
Senthilkumaar, S., Kalaamani, P., Subburaam, C.V., 2006. Liquid and heavy metals from multicomponent solutions using fly ash.
phase adsorption of crystal violet onto activated carbons derived Appl. Surf. Sci. 256, 5486–5491.
from male flowers of coconut tree. J. Hazard. Mater. 136, 800–808. Weber, W.J., Morris, J.C., 1963. Kinetics of adsorption on carbon
Shi, Y., Kong, X., Zhang, C., Chen, Y., Hua, Y., 2013. from solutions. J. Sanit. Eng. Div. 89, 31–60.
Adsorption of soy isoflavones by activated carbon: kinetics, Yener, J., Kopac, T., Dogu, G., Dogu, T., 2006. Adsorption of basic
thermodynamics and influence of soy oligosaccharides. Chem. yellow 28 from aqueous solutions with clinoptilolite and amberlite.
Eng. J. 215–216, 113–121. J. Colloid Interf. Sci. 294, 255–264.
Tan, I.W., Ahmad, A.L., Hameed, B.H., 2008. Adsorption of basic Zhou, L., Jin, J., Liu, Z., Liang, X., Shang, C., 2011. Adsorption of
dye using activated carbon prepared from oil palm shell: batch and acid dyes from aqueous solutions by the ethylenediamine-modified
fixed bed studies. Desalination 225, 13–28. magnetic chitosan nanoparticles. J. Hazard. Mater. 185, 1045–
Tempkin, M.J., Pyzhev, V., 1940. Kinetics of ammonia synthesis on 1052.
promoted iron catalysts. Acta Physicochim. URSS 12, 217–222. Zhou, Z., Lin, S., Yue, T., Lee, T., 2014. Adsorption of food dyes from
Thinakaran, N., Baskaralingam, P., Pulikesi, M., Panneerselvam, P., aqueous solution by glutaraldehyde cross-linked magnetic chitosan
Sivanesan, S., 2008. Removal of acid violet 17 from aqueous nanoparticles. J. Food Eng. 126, 133–141.
solutions by adsorption onto activated carbon prepared from
sunflower seed hull. J. Hazard. Mater. 151, 316–322.

Please cite this article in press as: Aljeboree, A.M. et al., Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell acti-
vated carbon. Arabian Journal of Chemistry (2014), http://dx.doi.org/10.1016/j.arabjc.2014.01.020