International Journal of Science and Research (IJSR), India Online ISSN: 2319-7064

Orthogonal Frequency Division Multiplexing and its

Applications
Beena R. Ballal1, Ankit Chadha2, Neha Satam3
1
Assistant Professor, Electronics and Telecommunication,
VIT, Wadala
Mumbai, India
[email protected]
2
Student, Electronics and Telecommunication,
VIT, Wadala
Mumbai, India
[email protected]
3
Student, Electronics and Telecommunication,
VIT, Wadala
Mumbai, India
[email protected]

Abstract: Orthogonal Frequency Division Multiplexing (OFDM) is a multi-carrier modulation technique which is very much popular
in new wireless networks of IEEE standard, digital television, audio broadcasting and 4G mobile communications. The main benefit of
OFDM over single-carrier schemes is its ability to cope with severe channel conditions without complex equalization filters. It has
improved the quality of long-distance communication by eliminating InterSymbol Interference (ISI) and improving Signal-to-Noise
ratio (SNR). The main drawbacks of OFDM are its high peak to average power ratio and its sensitivity to phase noise and frequency
offset. This paper gives an overview of OFDM, its applications in various systems such as IEEE 802.11a, Digital Audio Broadcasting
(DAB) and Digital Broadcast Services to Handheld Devices (DVB-H) along with its advantages and disadvantages.

Keywords: OFDM, Multipath Fading, Time-Slicing, Spectral Efficiency, ISI.

1. Introduction
802.20. OFDM converts a frequency-selective channel into a
During the last few decades, growth rate of wireless
parallel collection of frequency flat sub channels [2].Though
technology has been accelerated to such a level that it has
it is derived from frequency division multiplexing (FDM),
become ubiquitous. Progress in fiber-optics with assurance
OFDM provides many advantages over this conventional
of almost limitless bandwidth and predictions of universal
technique. In OFDM the subcarrier frequencies are chosen so
high-speed wireless internet access in the not-too-distant
that the signals are mathematically orthogonal over one
future thrive in both the popular press and technical journals
OFDM symbol period. Both modulation and multiplexing
[1].Wireless communication is having the fastest growth
are attained digitally using an inverse fast Fourier transform
phase in history because of unprecedented evolution in the
(IFFT) and thus, the required orthogonal signals can be
field. The kid of wireless communication is experiencing
generated accurately [3].
golden days due to various wireless standards such as Wi-Fi,
GSM, Wimax and LTE. These standards operate within This paper is organized as follows: Section 2 describes the
lower microwave range (2-4GHz). Due to intrinsic architecture of OFDM and Section 3 focuses on application
propagation losses at these frequencies and problem of of OFDM in various systems. Section 4 enlightens future
multipath fading, it was necessary to provide a solution work in this area. Finally, conclusions are presented in
which can offer robustness in multipath environments and Section 5.
against narrowband interference and is efficient. OFDM, in
all this aspects, proves to be an apt candidate by not only 2. Architecture of OFDM
providing high-capacity, high-speed wireless broadband
Practically, OFDM modulation for standard IEEE 802.20 is
multimedia networks but also coexists with current and
used by both the forward and reverse links. IEEE 802.20,
future systems.
also referred to as Mobile-Fi, is optimized for IP and
Orthogonal frequency-division multiplexing (OFDM) is a
roaming in high-speed mobile environments. This standard is
method of digital modulation in which a signal is split into
ready to fully mobilize IP, opening up major new data
several narrowband channels at different frequencies. OFDM
markets beyond the more circuit-centric 2.5G and 3G
has been adopted by several technologies such as
cellular standards. Its main operation is to develop the
Asymmetric Digital Subscriber Line (ADSL) services, IEEE
specification for an efficient packet-based air interface
802.11a/g, IEEE 802.16a, Digital Audio Broadcast (DAB),
optimized for the transport of IP-based services.
and digital terrestrial television broadcast: DVD in Europe,
ISDB in Japan 4G, IEEE 802.11n, IEEE 802.16, and IEEE
Volume 2 Issue 1, January 2013
www.ijsr.net 325
 International Journal of Science and Research (IJSR), India Online ISSN: 2319-7064

For IEEE 802.20, transmission on the forward link is divided 3. Application of OFDM in various systems
into super frames, where each super frame consists of a
3.1 In Standard IEEE 802.11a
preamble followed by a sequence of 25 Forward Link
Physical Layer (NFLPHY) frames [4]. Transmission on the
reverse link is also divided into units of super frames, with
each super frame consisting of a sequence of 25 reverse link
PHY frames.
In order to support cell sizes of macro, micro, and pico IEEE
802.20 should operate in a traditional cellular environment.
To increase the availability of coverage area, increase
throughput available to the users, and enable a higher overall
spectral efficiency, advanced antenna technologies such as
multi antenna at the base station should be employed.
The mathematical description for the OFDM signal is given
as follows:
The low-pass equivalent OFDM signal is expressed as
Figure 1: Block diagram of OFDM transceiver [6]
N −1
X (t ) = ∑ X k e
j 2πkt / T
, 0� � � � (1) In the transmitter, input data which is in binary is encoded by
k =0 a rate half convolution encoder. After interleaving, the binary
this is also Discrete Fourier Transform (DFT). Here � k are values are converted to QAM values [5]. Four pilot values
data symbols which is sequence of complex numbers are added to each 48 data value, so that coherency at the
representing BPSK, QPSK or QAM baseband symbol, N is reception point can be achieved. It gives 52 QAM values per
number of subcarriers and T is OFDM symbol line. The OFDM symbol. Application of IFFT modulates the symbol
� onto 52 subcarriers. Cyclic prefix is added to make the
subcarrier spacing makes them orthogonal over each
� system robust to multipath propagation. Narrower output
symbol period. spectrum is obtained by applying windowing. Using an IQ
Sequence of OFDM symbols is given as follows: modulator, the signal is converted to analog, which is up
converted to the 5 GHz band, amplified, and transmitted
+∞
through the antenna.
S (t ) = ∑ X (t − kT )
k = −∞
(2)

The receiver performs the reverse operations of the

transmitter, with few additional tasks. In the first step, the
To avoid ISI, a guard interval of length Tg is inserted before receiver has to estimate frequency offset and symbol timing,
OFDM block. During this interval, a cyclic prefix is using special training symbols in the preamble [6]. After
transmitted. The signal with cyclic prefix is thus given as, removing the cyclic prefix, the signal can be applied to a Fast
N −1 Fourier Transform to recover the 52 QAM values of all
X (t ) = ∑ X k e
j 2πkt / T
,-Tg�t�T (3) subcarriers. The training symbols and the pilot subcarriers
k =0 are used to correct for the channel response as well as
remaining phase drift. The QAM values are then demapped
The Fast Fourier Transform (FFT) is a computationally
into binary, and finally a Viterbi decoder decodes the
efficient implementation of DFT. Inverse Fast Fourier
information bits. Fig. 1 depicts block diagram of OFDM
Transform (IFFT) and FFT are main modulation and
transceiver.
demodulation techniques used in OFDM.
3.2 In Digital Audio Broadcasting (DAB)

Digital Audio Broadcasting (DAB) is a digital radio

technology for broadcasting radio stations, used in several
countries, especially in Europe. It has 4 transmission modes
with different parameters as shown in the Table 1.

Volume 2 Issue 1, January 2013

326
www.ijsr.net
 International Journal of Science and Research (IJSR), India Online ISSN: 2319-7064

Table 1: Digital Audio Broadcasting parameters [7]

Mode
Parameters Mode I Mode II Mode IV
III
No. of sub-
1536 384 192 768
carriers
Sub-carrier
1kHz 4kHz 8kHz 2kHz
spacing
Symbol
1.246ms 311.5us 155.8us 623us
time
Guard time 246us 61.5us 30.8us 123us Figure 2: Conceptual structure of a DVB-H receiver [8]
Carrier
<375MHz <1.5GHz <3GHz <1.5GHz
frequency It includes a DVB-H receiver (a DVB-T demodulator, a
Transmitter time-slicing module, and an optional MPE-FEC module) and
<96km <24km <12km <48km
separation a DVB-H terminal. The DVB-T demodulator recovers the
MPEG-2 transport stream (TS) packets from the received
The DAB transmitted data consists of number of signals DVB-T RF signal [8]. It offers three transmission modes:
sampled at a rate of 48 kHz with a 22-bit resolution [7]. This 8K, 4K, and 2K with the corresponding signaling. The time-
signal is then compressed at rates ranging from 32 to 384 slicing module controls the receiver to decode the wanted
kbps, depending upon the desired quality. The resulting service and shut off during the other service bits. It aims to
digital data is then divided into frames of 24 ms. DAB uses reduce receiver power consumption while also enabling a
differential QPSK modulation for the sub-carriers. A null- smooth and seamless frequency handover. The MPE-FEC
symbol indicates the start of the frame. A reference OFDM module, provided by DVB-H, offers in addition to the error
symbol is then sent to serve as a starting point for the correction in the physical layer transmission, a
differential decoding of the QPSK subcarriers. Differential complementary FEC function that allows the receiver to cope
Modulation avoids the use of complicated phase-recovery with particularly difficult reception situations.
schemes. DAB uses a rate quarter convolutional code with a
constraint length of 7 for error-correction. Interleaving is The advantages of DVB-H are as follows [9]:
used to separate the coded bits in the frequency domain as • Carriers - In DVB-H, carriers can use any additional
much as possible, which avoids large error bursts in the case spectrum that they might own for DVB-H broadcasting
of deep fades affecting a group of sub-carriers. and be an infrastructure player.
3.3 In DVB-H: Digital Broadcast Services to Handheld • Spectrum Availability - In U.S., DVB-H will be
Devices organized using clear and “ready-for-use” spectrum
available today, without interfering with existing analog
Digital Video Broadcasting (DVB) is a set of internationally TV stations or other TV or wireless services.
accepted standards for digital television. DVB-H is one of
the established mobile TV formats. It permits transmission
4. Advantages and disadvantages
of very large files and can operate on 5, 6, 7 or 8 MHz Advantages of OFDM are listed as follows:
bandwidth.
• OFDM makes resourceful utilization of the spectrum by
overlapping. By dividing the channel into narrowband flat
DVB-H uses OFDM air interface technology, and includes a fading sub channels, OFDM is more resistant to frequency
technique for power reduction in the tuner. It uses time- selective fading than single carrier systems.
slicing so that the tuner can be switched off most of the time • It can easily adapt to severe channel conditions without
and is only on during short transmission bursts. This allows complex time-domain equalization.
the tuner to operate over a reduced input bandwidth and also • It reduces ISI and IFI through use of a cyclic prefix and
conserves power. OFDM is a very good choice for a mobile fading caused by multipath propagation.
TV air interface. It offers good spectral efficiency, immunity • Using sufficient channel coding and interleaving lost
to multi-path, good mobile performance, and it works well in symbols can be recovered.
single-frequency networks such as those planned for mobile • Channel equalization becomes simpler than by using
TV. adaptive equalization techniques with single carrier
The structure of DVB-H is depicted in fig. 2. systems.
• OFDM is computationally capable by using FFT
techniques to implement the modulation and demodulation
functions.
• It is less sensitive to sample timing offsets than single
carrier systems are.
• It is robust against narrow-band co-channel interference.
• Unlike conventional FDM, tuned sub-channel receiver
filters are not required.
• It facilitates single frequency networks (SFNs); i.e.,
Volume 2 Issue 1, January 2013
327
www.ijsr.net
 International Journal of Science and Research (IJSR), India Online ISSN: 2319-7064

transmitter macro diversity. Author Profile

Beena Ballal is an Assistant Professor at Vidyalankar
The disadvantages are as follows:
Institute of Technology; Mumbai. She has a teaching
experience of 8 years and has interest in Optical fibers and
• The OFDM signal has a noise like amplitude with a very Digital logics. She has two national and three international
large dynamic range; hence it requires RF power publications to her credit.
amplifiers with a high peak to average power ratio.
• It is more sensitive to carrier frequency offset and drift Ankit Chadha is currently pursuing his undergraduate
than single carrier systems are due to leakage of the DFT. degree in Electronics and Telecommunication Engineering
• It is sensitive to Doppler shift. discipline at Vidyalankar Institute of Technology, Mumbai.
• It requires linear transmitter circuitry, which suffers from His fields of interest include Image Processing, Embedded
poor power efficiency. Systems.
• It suffers loss of efficiency caused by cyclic prefix.
Neha Satam is currently pursuing his undergraduate degree
5. Conclusion in Electronics and Telecommunication Engineering
discipline at Vidyalankar Institute of Technology, Mumbai.
OFDM has promising future in wireless networks and mobile Her fields of interest include Image Processing, Wireless
communications. Growth in number of worldwide customers Communication.
for wireless networks and ever-increasing demand for large
bandwidth has given birth to this technology. OFDM is
already playing an important role in WLAN and will be part
of MAN too. In coming years, it will surely dominate the
communication industry. Also, Wimax and 802.20 use
OFDM-MIMO, which is emerging as the main technology
for future cellular packet data networks, including 3GPP
long-term evolution and 3GPP2 air interface evolution as
well. Although OFDM has proven itself with packet-based
data, it is not yet clear whether the technology can either
handle large numbers of voice customers or work with voice
and data as well as CDMA.

References
[1] Gary J. Mullett, Wireless Communication (Thomson
Delmar Learning, 2006).
[2] Gordon L. Stüber, John R. Barry, Steve W. Mclaughlin,
Ye (Geoffrey) Li, Mary Ann Ingram, Thomas G. Pratt,
Broadband MIMO-OFDM Wireless Communications,
Proceedings Of The IEEE, 92(2), 2004, 271-294.
[3] Jean Armstrong, OFDM for Optical Communications,
Journal Of Light wave Technology, 27(3),2009 189-204.
[4] Y. Awad, L. H. Crockett and R. W. Stewart, OFDM
Transceiver for IEEE 802.20 Standards,17th European
Signal Processing Conference, 2009, Glasgow, Scotland.
[5] A. Pavani , Dr. E. V. Krishna Rao and Dr. B. Prabhakara
Rao, A New OFDM Standard for High Rate Wireless
LAN in the 5 GHz Band, International Journal of Future
Generation Communication and Networking, 4( 4)2011,
57-64.
[6] Aníbal Luis Intini, Orthogonal Frequency Division
Multiplexing for Wireless Networks Standard IEEE
802.11a, University of California, 2000,1-40.
[7] Vijaya Chandran Ramasami, Orthogonal Frequency
Division Multiplexing.
[8] Gerard Faria, Jukka A. Henriksson, Erik Stare, And
PekkaTalmola, DVB-H: Digital Broadcast Services to
Handheld Devices, Proceedings of the IEEE,
94(1),2006, 194-209.
[9] Texas Instruments, DVB-H mobile digital TV for the
U.S.

Volume 2 Issue 1, January 2013

www.ijsr.net 328