Scribd
Upload
400 views3 pages

Manual For Columns and Struts Apparatus

This document provides instructions for conducting an experiment using a columns and struts apparatus. The experiment aims to study column buckling behavior and calculate the Euler buckling load for columns with different end conditions, including both ends fixed, both ends pinned, and one end fixed with the other pinned. Students are instructed to apply a gradually increasing load to each column and record the buckling load, then compare the observed buckling loads and effective lengths to theoretical calculations.

Uploaded by

ramniwas123
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
400 views3 pages

Manual For Columns and Struts Apparatus

This document provides instructions for conducting an experiment using a columns and struts apparatus. The experiment aims to study column buckling behavior and calculate the Euler buckling load for columns with different end conditions, including both ends fixed, both ends pinned, and one end fixed with the other pinned. Students are instructed to apply a gradually increasing load to each column and record the buckling load, then compare the observed buckling loads and effective lengths to theoretical calculations.

Uploaded by

ramniwas123
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

INSTRUCTIONAL MANUAL FOR

COLUMNS AND STRUTS APPARATUS

COLUMNS AND STRUTS APPARATUS


1.0 THEORY:

If compressive load is applied on a column, the member may fail either by


crushing or by buckling depending upon its material, cross section and
length. If member is considerably long in comparison to its lateral
dimensions it will fail by bucking. If a member shows signs of bucking the
member leads to failure with small increase in load. The load at which the
member just buckles is called buckling or critical load. For a slender column,
buckling load is less than the crushing load. The buckling load, as given by
Euler, can be found by using following expression:

Where;
E = Modulus of elasticity
= 2.0 x 105 N/mm2 for steel
I = Least moment of inertia of column section
1e = Effective length of column

Depending on support conditions, four cases may arise. The effective length
for each of which are given as:

1. Both ends are fixed


1e= L/2

2. One end is fixed and other is pinned


1e = L/2

3. Both ends are pinned


1e =L
Where; L is distance between points of fixity at top and bottom i.e.
unsupported length.

2.0 OBJECTIVE:

 To study the behavior of different types of columns and to calculate the


Euler's buckling load for each case.

3.0 APPARATUS:

Apparatus consists of four spring steel columns, which are put along a
vertical wooden board. These four columns have different end conditions as
below:
1. Both ends pinned
2. Both ends fixed
3. One end pinned and other fixed

4.0 SUGGESTED EXPERIMENAL WORK:

1. Pin a graph paper on the wooden board behind the column.


2. Apply the load at the top of columns increasing gradually. At certain stage of
loading the columns shows abnormal deflections and gives the buckling load.
3. Note the buckling load for each of the four columns.
4. Trace the deflected shapes of the columns over the paper. Mark the points of
change of curvature of the curves and measure the effective or equivalent
length for each case separately.
5. Also calculate the theoretical effective lengths and thus buckling loads by the
expressions given above and compare them with the observed values.

5.0 RESULTS AND DISCUSSIONS:

1. Calculate the Euler's buckling load for each case.


2. Also calculate the theoretical effective lengths and thus buckling loads by the
expressions given above and compare them with the observed values.

6.0 SAMPLE DATA SHEET:

Width of strip (mm), b =


Thickness of strip (mm), t =
Length of strip (mm), L =
bt3
Least moment of inertia, I = -------
12

Sr. End conditions Euler's Effective


No. Buckling load Length (mm)
Theoretic Observed Theoretical Observed
al
1. Both ends fixed
2. One end fixed and
3. other pinned

You might also like