BLDG

INFO
Design of Building
INFORMATION OF PROPOSED BUILDING
S.No.
1 Type of Building(Framed / Loadbearing) = Framed Building
2 Nos. of Storey = 3
3 Floor to floor height of building = 3000 mm
4 Height of plinth = 450 mm
5 Depth of foundation = 1000 mm
6 Bearing Capacity of soil = 200 KN/sq.m.
7 Thickness of external wall = 230 mm
8 Thickness of internal wall = 125 mm
Assumptions
Design Philosophy Limit state of design as per IS:456-1978
1 Grade of concrete = 20 N/sq.mm.
2 Grade of steel = 415 N/sq.mm.
3 Dia of bar for slab = 8 mm Dia of bar for column
4 Dia of bar for beam = 20 mm Cover for column
5 Cover For Slab = 15 mm
6 Cover For Beam = 25 mm
FOR SLAB
7 Dead load(Superimposed) = 1.5 KN/sq.m.
8 Live load = 1.5 KN/sq.m.
9
10
( The thickness of slab should be kept to low as its volume/load ratio is very high)
11 FOLLOWING ARE CONDITION FOR TWO - WAY SLAB
Case Nos.Type of Panel Short span coefficient
1 Interior
2 One short edge Discontinuous
3 One long edge Discontinuous
4 Two adjacent edge Discontinuous
5 Two short edge Discontinuous
6 Two long edges Discontinuous
7 Three edges Discontinuous (except long)
8 Three edges Discontinuous (except short)
9 Four edges Discontinuous
12 For calculation of Ratio of Max.span/Deff. Linear interpolation has been considered for Chart 22
of Design Aids to IS:456
13 The Design can be done for M15 or M20 grade of concrete for slab,beam,Column.
14 The Beam can be designed for Mu/b d^2=6.38 N/sq.mm
15 For design of beam as doubly reinforced, no effect of d'/Deff. is
considered and the reionforcement available for d'/Deff=.2
16 For design of Column the value of Mu/fckb d^2 is required to be seen from chart 31-34
for reinforced distribuited equally on two sides for rectangular section,from chart 43-46
for reinforced distribuited equally on four sides for rectangular section,from chart 55-58
for reinforced distribuited equally circular section.
17 For design of two - way slab first the longest/Shortest span value must be entered,
so that no contradictory statment should be generated at any instant of time.
18 Weight of RCC concrete is assumed 25 KN/sq.m.
19 For cantilever slab Maximum moment calculated by weight of slab / metre
width/metre lengthxeff. length ^2/2
Page 1
INFO
20 For Simply supported slab Maximum moment calculated by weight of slab /

metre width/metre lengthxeff. length ^2/8
21 For Simply supported continuous slab Maximum moment calculated by following formulae
given in article 21.5.1 table 7 of IS:456-1978 as follows
Span Moment Support moment
Middle end Middle Interior Next to end Support End Support
Dead Load WdxL^2/12 WdxL^2/16 WdxL^2/10 WdxL^2/12
Live Load WlxL^2/10 WlxL^2/12 WlxL^2/9 WlxL^2/9
Where Wd =Factored Dead Load
Wl =Factored Live Load
L = Effective Span
22 For Two-Way slab Maximum moment calculated by following equations as
article C.1.1 of Appendix C of IS:456-1978
Mx = AlphaXxWxLx^2
My = AlphaYxWxLx^2
23 All dimension are in KN,metre,mm
Type of slab Nos. Dimension of sl %Steel Max.Span
slab Length Width Deff. RESULDEPTH
mms mms mms
Cantilever 1 1000 0.22 11.06 O.K. 100
2 2000 0.22 11.06 O.K. 150
3 2500 0.24 10.61 O.K. 200
Simply Supported 1 2360 0.15 36.16 REVIS 120
2 1600 0.13 37.61 REVIS 110
3 3000 0.23 30.94 O.K. 140
Simply supported Cont. 1 4000 0.3 35.10 O.K. 170
When Nos. of span=>3 2 3700
When span is within 15% of 3 4300
Longest span
Two way slab Nos.
4 1 9000 5000 0.3 35.10 O.K. 100
Condition 2 2 3250 2650 0.24 39.40 O.K. 110
3 3 5000 4000 0.23 40.22 O.K. 120
Column shape if Rectangular = 1 = 1 % Ast Span/Deff.

if Circular = 2 0.1 40
Reinforcement if on two sides =1 = 2 0.2 33
if on four sides = 2 0.3 27
0.4 25.5
0.5 23.5
0.6 22.5
0.7 21.3
Page 2
INFO
25
40
for Chart 22
Page 3
INFO
DEP.
PRO.
mms
110
200
260
120
110
140
170
170
110
120
Span/Deff.
0.025
0.03
0.037
0.039
0.043
0.044
0.047
Page 4
CSLAB
DESIGN OF CANTILEVER ROOF SLAB

Design of Cantilever Slab
Cantilever slab No. 1 2 3
Concentrated load on cantilever slab due to parapet wall
Effective cover 19 19 19
span of slab 1000 2000 2500
Assume % steel 0.22 0.22 0.24
Modified L/d ratio 11.06 11.06 10.61
Required Eff. Depth 90 181 236
Total depth required 109 200 255
Total depth provided 110 200 260
Weight of slab 2.75 5 6.5
Superimposed Load 1.5 1.5 1.5
Live load 1.5 1.5 1.5
Total factored load 9 12 15
Design moment 4.5 24 46.88
Eff. Depth reqd. 40 93 130
Depth provided 110 200 260
Eff. depth provided 91 181 241
Mu/bd^2 0.543 0.733 0.807
% steel 0.16 0.21 0.24
Area of steel 142 384 567
Dia. of bar 8 10 12 8 10 12 8 10 12
Spacing of bar require 355 554 798 131 204 294 88.7 139 199
Maximum spacing of bar 273 543 723
Hence,spacing 273 273 273 131 204 294 88.7 139 199
Check for Serviceability O.K. O.K. O.K.
Distribution Steel 0.12 0.12 0.12

132 240 312
8 10 12 8 10 12 8 10 12
381 595 856 209 327 471 161 252 362
273 543 723
270 270 270 200 320 450 160 250 360
Page 5
SSSLAB
DESIGN OF ROOF SLAB

Design of Simply Supported Slab
Simply Supported slab No 1 2 3
span of slab 2360 1600 3000
Assume % steel 0.15 0.13 0.23
Weight of slab 3 2.75 3.5
Superimposed Load 1.5 1.5 1.5
Live load 1.5 1.5 1.5
Total factored load 9 9 10
Design moment 6.266 2.88 11.25
Eff. Depth reqd. 48 32 64
Depth provided 80 65.26 120 80 42.55 110 140 97 140
Final Total Depth 120 110 140
Eff. depth provided 101 91 121
Mu/bd^2 0.614 0.348 0.768
% steel 0.18 0.145 0.22
Area of steel 178 132 270
Dia. of bar 8 10 12 16 8 10 12 16 8 10 12 16
Spacing of bar requ 282 440 633 1121 381 595 856 1515 186 291 418 740
Maximum spacing of bar 303 273 363
Hence,spacing 280 300 300 300 270 270 270 270 180 290 360 360
Check for Serviceability Unsafe Unsafe O.K.
Distribution Steel 0.12 0.12 0.12

144 132 168
8 10 12 8 10 12 8 10 12
349 545 785 381 595 856 299 467 673
303 273 363
300 300 300 270 270 270 290 360 360
Page 6
SCSLAB
DESIGN OF ROOF SLAB

Design of Continuous supported Slab
Simply Supported slab No. 1 2 3
span of slab 4000 3700 4300
Assume % steel 0.3 0.3 0.3
Average span 4000
Weight of slab 4.25 4.25 4.25
Dead load 1.5 1.5 1.5
Live Load 1.5 1.5 1.5
Total Factored Dead Load 9.0 9 9
Design moment Mid Span At Support
end interior At end Interior
Dead Load 12.0 9.00 14.40 16.00
Live Load 2.40 2.00 2.67 2.67
Total Moment 14.4 11.00 17.07 18.67
Eff. Depth reqd. 72 63 79 82
Depth provided 170 100 140 170 90 130 170 79 170
170 170
FINAL TOTAL DEPTH 170
Eff. depth provided 151 151 151 151
% steel 0.18 0.12 0.16 0.18
Area of steel 275 181.2 246 270
Dia. of bar 8 10 12 8 10 12 8 10 12 8 10 12
Spacing of bar req 183 286 411 277 433 624 204 319 459 186 290 418
Maximum spacing of bar 453 453 453 453
Hence,spacing 180 280 410 270 430 450 200 310 450 180 290 410 410
Check for Serviceability O.K. O.K. O.K. O.K.
O.K.
Distribution Steel 0.12
204
8 10 12
246 385 554
453
240 380 450
Page 7
TWSLAB
DESIGN OF ROOF SLAB

Design of Two way slab
Two way slab Nos. 1 2 3.000
span of slab Length Width Length Width Length Width
9000 5000 3250 2650 5000 4000
Ly/Lx 1.80 1.226 1.25
Assume % steel 0.3 0.24 0.230
Weight of slab 4.25 2.75 3.000
Factored Dead load 8.6 6.4 6.8
Factored Live Load 2.3 2.25 2.250
Total Factored load 10.9 8.6 9.000
Table shown is as per Table 22 of IS:456-1978
Case Nos. Type of Panel Short span coefficient Long Span Coeff.
1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 3
1 Interior 1 0.032 0.037 0.043 0.047 0.051 0.053 0.055 0.058 0.06 0.063 0.065 0.032
2 0.024 0.028 0.032 0.036 0.039 0.041 0.043 0.044 0.046 0.047 0.049 0.024
2 One short edge 3 0.037 0.043 0.048 0.051 0.055 0.057 0.059 0.061 0.064 0.066 0.068 0.037
Discontinuous 4 0.028 0.032 0.036 0.039 0.041 0.044 0.046 0.047 0.049 0.05 0.052 0.028
3 One long edge 5 0.037 0.044 0.052 0.057 0.063 0.067 0.071 0.074 0.078 0.081 0.085 0.037
Discontinuous 6 0.028 0.033 0.039 0.044 0.047 0.051 0.054 0.057 0.059 0.062 0.065 0.028
4 Two adjacent edge 7 0.047 0.053 0.06 0.065 0.071 0.075 0.078 0.081 0.085 0.088 0.091 0.047
Discontinuous 8 0.035 0.04 0.045 0.049 0.053 0.056 0.059 0.061 0.064 0.066 0.069 0.035
5 Two short edge 9 0.045 0.049 0.052 0.056 0.059 0.06 0.062 0.064 0.065 0.067 0.069 0
Discontinuous 10 0.035 0.037 0.04 0.043 0.044 0.045 0.046 0.048 0.049 0.051 0.052 0.035
6 Two long edges 11 0 0 0 0 0 0 0 0 0 0 0 0.045
Discontinuous 12 0.035 0.043 0.051 0.057 0.063 0.068 0.072 0.076 0.08 0.084 0.088 0.035
7 Three edges (except long) 13 0.057 0.064 0.071 0.076 0.08 0.084 0.087 0.089 0.092 0.094 0.097 0
Discontinuous 14 0.043 0.048 0.053 0.057 0.06 0.064 0.066 0.068 0.069 0.071 0.073 0.043
8 Three edges (except short) 15 0 0 0 0 0 0 0 0 0 0 0 0.057
Discontinuous 16 0.043 0.051 0.059 0.065 0.071 0.076 0.08 0.084 0.088 0.092 0.096 0.043
9 Four edges 17 0 0 0 0 0 0 0 0 0 0 0 0
Discontinuous 18 0.056 0.064 0.072 0.079 0.085 0.089 0.093 0.096 0.1 0.103 0.107 0.056
Design moment Short Span Long Span
Negative Positive Negative Positive
Page 8
TWSLAB
Coeff. Moment Coeff. Momen Coeff. Moment Coeff. Moment
1.80 1.9 1.80 1.9

0.085 0.088 0.0846 23.00 0.064 0.066 0.064 17.35 0.047 12.78 0.035 9.516
Err:502 Err:502 Err:502 Err:502 Err:502 ### ### ### ### ### ### ###
Total Moment 23.00 17.35 12.78 9.52
Absolute Maximum B.M. 23.00
Eff. Depth reqd. 91
Depth provided 110 110 110 100 170
Mu/bd^2 1.01 0.76 0.56 0.42
% steel 0.30 0.22 0.16 0.135

Area of steel 450 333.6 242.6 204
Dia. of bar 8 10 12 8 10 12 8 10 12 8 10 12
Spacing of bar requir 112 174 251 151 235 339 207 324 466 246 385 554
Hence,spacing 110 170 250 150 230 330 200 320 450 240 380 450
Page 9
TWSLAB

O.K.

204
8 10 12
246 385 554
453
240 380 450

1.20 1.3 1.20 1.3
0.048 0.051 0.049 2.96 0.036 0.039 0.037 2.228 0.037 2.241 0.028 1.696
Total Moment 2.96 2.23 2.24 1.696
Eff. Depth reqd. 33
Depth provided 80 80 80 110 67
Page 10
TWSLAB

Mu/bd^2 0.357 0.269 0.271 0.205
% steel 0.15 0.15 0.15 0.145
Area of steel 132 132 132 132
Dia. of bar 8 10 12 8 10 12 8 10 12 8 10 12
Hence,spacing 270 270 270 270 270 270 270 270 270 270 270 270 270
O.K.
132
8 10 12
381 595 856
273
270 270 270
1.20 1.3 1.20 1.3
0.052 0.057 0.055 7.85 0.039 0.044 0.042 5.976 0.037 5.328 0.028 4.032
Total Moment 7.85 5.98 5.33 4.032
Eff. Depth reqd. 53
Depth provided 80 120 100
Mu/bd^2 0.769 0.586 0.522 0.395
% steel 0.22 0.17 0.15 0.143
Area of steel 226 169.9 150.9 144
Dia. of bar mm. 8 10 12 8 10 12 8 10 12 8 10 12
Hence,spacing 220 300 300 290 300 300 300 300 300 300 300 300 300
O.K.
144
Page 11
TWSLAB
8 10 12
349 545 785
303
300 300 300
Page 12
LC
LOAD CALCULATION
Dead load 1.50 kn/m^2
Live load 1.50 kn/m^2
Wall load (Main) 13.11 kn/m
S. No. D.L. L.L. Span D.L. L.L. W.L. TOTAL

sq. metre sq. metre per metre per metre per metre
1 1.5 1.5 2360 1.77 1.77 13.11 16.65
2
3
4
5
6
7
TWO-WAY SLAB ROOF LOAD

sq. metre sq. metre Long Short per metre per metre per metre
Short Span 1.5 1.5 9000 5000 2.50 2.50 13.11

Long Span 1.5 1.5 9000 5000 3.36 3.36 13.11
Short Span 1.5 1.5 3250 2650 1.33 1.33 13.11
Long Span 1.5 1.5 3250 2650 1.55 1.55 13.11
TWO-WAY SLAB FLOOR LOAD
sq. metre sq. metre Long Short per metre per metre per metre
Short Span 1.5 1.5 9000 5000 2.50 2.50 13.11 18.11
Long Span 1.5 1.5 9000 5000 3.36 3.36 13.11 19.84
Short Span
Long Span
Page 13
LC
7.13 kn/m
18.11
19.84
15.76
16.20
Page 14
MD
MOMENT DISTRIBUTION FOR PB1
Slab Wall Self Wt. Others Total Fact.

1 0.99 1.38 0.23 0.46 3.06 Load
4.59
2 0.99 1.38 0.23 0.46 3.06 4.59
3 0.62 1.38 0.23 0.46 2.69 4.04
4 0.32 1.38 0.23 0.46 2.39 3.58
Distribution factor for two span
Width Depth LengthMoment oStiffness Total Distribution

Inertia Stiffness Factor
1 Beam 1 230 300 2,200 5E+08 235,227 0.37
2 Beam 2 230 300 2,200 5E+08 235,227 633,215 0.37
Col.B 250 250 2,000 3E+08 162,760 0.26
Col.T 0 0 3,000 0E+00 0 0.00

2 Beam 1 230 300 2,200 5E+08 235,227 0.40
3 Beam 2 230 300 2,800 5E+08 184,821 582,809 0.32
Col.B 250 250 2,000 3E+08 162,760 0.28
Col.T 0 0 3,000 0E+00 0 0.00

2 Beam 1 230 300 2,800 5E+08 184,821 0.26
3 Beam 2 230 300 1,400 5E+08 369,643 717,225 0.52
Col.B 250 250 2,000 3E+08 162,760 0.23
Col.T 0 0 3,000 0E+00 0 0.00
Page 15
MD
1 Mab -1.85 1.85

2 Mbc -1.85 1.85
3 Mcd -2.64 2.64
4 Mde -0.59 0.59
BEAM BEAM COLUMN BEAM BEAM COLUMN BEAM BEAM COLUMN BEAM BEAM
0.37 0.26 0.37 0.40 0.28 0.32 0.26 0.23 0.52

-1.85 1.85 -1.85 1.85 -2.64 2.64 -0.59 0.59
0.00 0.00 0.00 0.32 0.22 0.25 -0.53 -0.47 -1.06
0.00 0.16 0.00 -0.26 0.13 -0.53
-0.06 -0.04 -0.06 0.11 0.07 0.08 -0.03 -0.03 -0.06
-0.03 0.05 -0.03 -0.02 0.04 -0.03
-0.02 -0.01 -0.02 0.02 0.01 0.01 -0.01 -0.01 -0.02
-0.01 -0.01
-1.89 1.77 -0.05 -1.72 2.27 0.31 -2.57 2.23 -0.50 -1.73 0.01
Vertical L 5.05 5.05 5.05 5.05 5.66 5.66 2.51 2.51

Vertical L 0.05 -0.05 -0.25 0.25 0.12 -0.12 1.23 -1.23
Moment
Total 5.10 5.00 4.80 5.30 5.78 5.54 3.73 1.28
Load
Page 16
MD
MOMENT DISTRIBUTION FOR PB4/PB7
Fact.
Slab Wall Self Wt. Others Total
Load
1 0.99 1.38 0.23 0.46 3.06 4.59
2 0.99 0.75 1.38 0.23 0.00 3.35 5.02
3 0.99 0.75 1.38 0.23 0.00 3.35 5.02

1 Beam 1 230 300 1,200 5E+08 431,250 0.47
2 Beam 2 230 300 1,600 5E+08 323,438 917,448 0.35
Col.B 250 250 2,000 3E+08 162,760 0.18
Col.T 0 0 3,000 0E+00 0 0.00

2 Beam 1 230 300 1,600 5E+08 323,438 0.40
3 Beam 2 230 300 1,600 5E+08 323,438 809,635 0.40
Col.B 250 250 2,000 3E+08 162,760 0.20
Col.T 0 0 3,000 0E+00 0 0.00
1 Mab -0.55 0.55

2 Mbc -1.07 1.07
3 Mcd -1.07 1.07
Page 17
MD
BEAM BEAM COLUMN BEAM BEAM COLUMN BEAM BEAM
0.47 0.18 0.35 0.40 0.20 0.40

-0.55 0.55 -1.07 1.07 -1.07 1.07
0.24 0.09 0.18 0.00 0.00 0.00
0.12 0.00 0.09 0.00
0.00 0.00 0.00 -0.04 -0.02 -0.04
0.00 -0.02 0.00 -0.02
0.01 0.00 0.01 0.00 0.00 0.00
0.00 0.00
-0.42 0.80 0.10 -0.90 1.13 -0.02 -1.11 1.05
Vertical L 2.75 2.75 4.02 4.02 4.02 4.02

Vertical L -0.32 0.32 -0.14 0.14 0.03 -0.03
Moment
Total 2.44 3.07 3.88 4.16 4.05 3.98
Load
Fact
L
1 0.75 0.75 1.38 0.23 0.00 3.11 4.67
2 0.75 0.75 1.38 0.23 0.00 3.11 4.67
3 0.54 0.54 1.38 0.23 0.00 2.69 4.04

1 Beam 1 230 300 1,600 5E+08 323,438 0.40
2 Beam 2 230 300 1,600 5E+08 323,438 809,635 0.40
Page 18
MD
Col.B 250 250 2,000 3E+08 162,760 0.20

Col.T 0 0 3,000 0E+00 0 0.00

2 Beam 1 230 300 1,600 5E+08 323438 0.45
3 Beam 2 230 300 2,300 5E+08 225000 711,198 0.32
Col.B 250 250 2,000 3E+08 162760 0.23
Col.T 0 0 3,000 0E+00 0 0.00
1 Mab -1.00 1.00

2 Mbc -1.00 1.00
3 Mcd -1.78 1.78
BEAM BEAM COLUMN BEAM BEAM COLUMN BEAM BEAM
0.40 0.20 0.40 0.45 0.23 0.32

-1.00 1.00 -1.00 1.00 -1.78 1.78
0.00 0.00 0.00 0.36 0.18 0.25
0.00 0.18 0.00 0.12
-0.07 -0.04 -0.07 0.00 0.00 0.00
-0.04 0.00 -0.04 0.00
0.00 0.00 0.00 0.02 0.01 0.01
0.00 0.01
-1.03 0.92 -0.04 -0.89 1.33 0.19 -1.52 1.91
Vertical L 3.73 3.73 3.73 3.73 4.64 4.64

Vertical L 0.07 -0.07 -0.28 0.28 -0.17 0.17
Moment
Page 19
MD
Total 3.80 3.67 3.45 4.01 4.47 4.81

Load
Fact.
Load
1 0.75 0.75 1.38 0.23 0.00 3.11 4.67
2 0.75 0.75 1.38 0.23 0.00 3.11 4.67
3 0.54 0.54 1.38 0.23 2.69 4.04
4 0.99 0.99 1.38 0.23 0.00 3.59 5.38

1 Beam 1 230 300 2,200 5E+08 235,227 0.37
2 Beam 2 230 300 2,200 5E+08 235,227 633,215 0.37
Col.B 250 250 2,000 3E+08 162,760 0.26
Col.T 0 0 3,000 0E+00 0 0.00

2 Beam 1 230 300 2,200 5E+08 235,227 0.40
3 Beam 2 230 300 2,800 5E+08 184,821 582,809 0.32
Col.B 250 250 2,000 3E+08 162,760 0.28
Col.T 0 0 3,000 0E+00 0 0.00
Page 20
MD

3 Beam 1 230 300 2,800 5E+08 184,821 0.26
4 Beam 2 230 300 1,400 5E+08 369,643 717,225 0.52
Col.B 250 250 2,000 3E+08 162,760 0.23
Col.T 0 0 3,000 0E+00 0 0.00
1 Mab -1.88 1.88

2 Mbc -1.88 1.88
3 Mcd -2.64 2.64
4 Mde -0.88 0.88
0.37 0.26 0.37 0.40 0.28 0.32 0.26 0.23 0.52

-1.88 1.88 -1.88 1.88 -2.64 2.64 -0.88 0.88
0.00 0.00 0.00 0.30 0.21 0.24 -0.45 -0.40 -0.91
0.00 0.15 0.00 -0.23 0.12 -0.45
-0.06 -0.04 -0.06 0.09 0.06 0.07 -0.03 -0.03 -0.06
-0.03 0.05 -0.03 -0.02 0.04 -0.03
-0.02 -0.01 -0.02 0.02 0.01 0.01 -0.01 -0.01 -0.02
-0.01 -0.01
-1.92 1.81 -0.05 -1.76 2.27 0.29 -2.55 2.30 -0.43 -1.86 0.39
Vertical L 5.13 5.13 5.13 5.13 5.65 5.65 3.77 3.77

Vertical L 0.05 -0.05 -0.23 0.23 0.09 -0.09 1.06 -1.06
Moment
Total 5.18 5.08 4.90 5.36 5.74 5.56 4.82 2.71
Load
Page 21
MD
Fact.
1 0.80 1.38 0.23 0.46 2.87 4.31

2 0.80 1.38 0.23 0.46 2.87 4.31
3 0.80 1.38 0.23 0.46 2.87 4.31 4.86
4 0.80 1.38 0.23 0.46 2.87 4.31
5 0.80 1.38 0.23 0.46 2.87 4.31

1 Beam 1 230 300 1,935 5E+08 267,442 0.38
2 Beam 2 230 300 1,935 5E+08 267,442 697,644 0.38
Col.B 250 250 2,000 3E+08 162,760 0.23
Col.T 0 0 3,000 0E+00 0 0.00

2 Beam 1 230 300 1,935 5E+08 267,442 0.41
3 Beam 2 230 300 2,260 5E+08 228,982 659,185 0.35
Col.B 250 250 2,000 3E+08 162,760 0.25
Col.T 0 0 3,000 0E+00 0 0.00

3 Beam 1 230 300 2,260 5E+08 228,982 0.35
4 Beam 2 230 300 1,935 5E+08 267,442 659,185 0.41
Col.B 250 250 2,000 3E+08 162,760 0.25
Col.T 0 0 3,000 0E+00 0 0.00
Page 22
MD

4 Beam 1 230 300 1,935 5E+08 267,442 0.38
5 Beam 2 230 300 1,935 5E+08 267,442 697,644 0.38
Col.B 250 250 2,000 3E+08 162,760 0.23
Col.T 0 0 3,000 0E+00 0 0.00
1 Mab -1.34 1.34

2 Mbc -1.34 1.34
3 Mcd -3.21 3.21
4 Mde -1.34 1.34
5 Mef -1.34 1.34
BEAM BEAM COLUMN BEAM BEAM COLUMN BEAM BEAM COLUMN BEAM BEAM COLUMN BEAM BEAM
0.38 0.23 0.38 0.41 0.25 0.35 0.35 0.25 0.41 0.38 0.23 0.38
-1.34 1.34 -1.34 1.34 -3.21 3.21 -1.34 1.34 -1.34 1.34
0.00 0.00 0.00 0.76 0.46 0.65 -0.65 -0.46 -0.76 0.00 0.00 0.00
0.00 0.38 0.00 -0.32 0.32 0.00 -0.38 0.00
-0.14 -0.09 -0.14 0.13 0.08 0.11 -0.11 -0.08 -0.13 0.14 0.09 0.14
-0.07 0.07 -0.07 -0.06 0.06 0.07 -0.07 0.07
-0.03 -0.02 -0.03 0.05 0.03 0.04 -0.04 -0.03 -0.05 0.03 0.02 0.03
-0.01 0.01
-1.43 1.17 -0.10 -1.07 2.21 0.57 -2.78 2.78 -0.57 -2.21 1.07 0.10 -1.17 1.43
Vertical
load 4.17 4.17 4.17 4.17 7.29 7.29 4.17 4.17 4.17 4.17
Vertical
load due 0.13 -0.13 -0.59 0.59 0.00 0.00 0.59 -0.59 -0.13 0.13
Moment
Total V 4.30 4.03 3.58 4.75 7.29 7.29 4.75 3.58 4.03 4.30
Load
Page 23
MD
Fact.
1 0.80 0.87 1.38 0.23 0.00 3.28 4.92

2 0.80 0.87 1.38 0.23 0.00 3.28 4.92
3 0.80 0.84 1.38 0.23 0.00 3.25 4.88
4 0.80 0.84 1.38 0.23 0.00 3.25 4.88
5 0.80 0.84 1.38 0.23 0.00 3.25 4.88
6 0.80 0.84 1.38 0.23 0.00 3.25 4.88
7 0.80 0.87 1.38 0.23 0.00 3.28 4.92
8 0.80 0.87 1.38 0.23 0.00 3.28 4.92

1 Beam 1 230 300 2,300 5E+08 225,000 0.30
2 Beam 2 230 300 1,400 5E+08 369,643 757,403 0.49
Col.B 250 250 2,000 3E+08 162,760 0.21
Col.T 0 0 3,000 0E+00 0 0.00

2 Beam 1 230 300 1,400 5E+08 369,643 0.50
3 Beam 2 230 300 2,520 5E+08 205,357 737,760 0.28
Col.B 250 250 2,000 3E+08 162,760 0.22
Col.T 0 0 3,000 0E+00 0 0.00

3 Beam 1 230 300 2,520 5E+08 205,357 0.25
4 Beam 2 230 300 1,130 5E+08 457,965 826,082 0.55
Col.B 250 250 2,000 3E+08 162,760 0.20
Page 24
MD
Col.T 0 0 3,000 0E+00 0 0.00

4 Beam 1 230 300 1,130 5E+08 457,965 0.42
5 Beam 2 230 300 1,130 5E+08 457,965 1,078,690 0.42
Col.B 250 250 2,000 3E+08 162,760 0.15
Col.T 0 0 3,000 0E+00 0 0.00

5 Beam 1 230 300 1,130 5E+08 457,965 0.55
6 Beam 2 230 300 2,520 5E+08 205,357 826,082 0.25
Col.B 250 250 2,000 3E+08 162,760 0.20
Col.T 0 0 3,000 0E+00 0 0.00

6 Beam 1 230 300 2,520 5E+08 205,357 0.28
7 Beam 2 230 300 1,400 5E+08 369,643 737,760 0.50
Col.B 250 250 2,000 3E+08 162,760 0.22
Col.T 0 0 3,000 0E+00 0 0.00

7 Beam 1 230 300 1,400 5E+08 369,643 0.49
8 Beam 2 230 300 2,300 5E+08 225,000 757,403 0.30
Col.B 250 250 2,000 3E+08 162,760 0.21
Page 25
MD
Col.T 0 0 3,000 0E+00 0 0.00
1 Mab -2.17 2.17

2 Mbc -0.80 0.80
3 Mcd -2.58 2.58
4 Mde -0.52 0.52
5 Mef -0.52 0.52
6 Mfg -2.58 2.58
7 Mgh -0.80 0.80
8 Mhi -2.17 2.17
BEAM BEAM COLUMN BEAM BEAM COLUMN BEAM BEAM COLUMN BEAM BEAM COLUMN BEAM BEAM COLUMN BEAM BEAM COLUMN BEAM BEAM COLUMN BEAM BEAM
0.30 0.21 0.49 0.50 0.22 0.28 0.25 0.20 0.55 0.42 0.15 0.42 0.55 0.20 0.25 0.28 0.22 0.50 0.49 0.21 0.30
-2.17 2.17 -0.80 0.80 -2.58 2.58 -0.52 0.52 -0.52 0.52 -2.58 2.58 -0.80 0.80 -2.17 2.17
-0.41 -0.29 -0.67 0.89 0.39 0.49 -0.51 -0.41 -1.14 0.00 0.00 0.00 1.14 0.41 0.51 -0.49 -0.39 -0.89 0.67 0.29 0.41
-0.20 0.44 -0.33 -0.26 0.25 0.00 -0.57 0.57 0.00 -0.25 0.26 0.33 -0.44 0.20
-0.13 -0.10 -0.22 0.30 0.13 0.16 -0.06 -0.05 -0.14 0.00 0.00 0.00 0.14 0.05 0.06 -0.16 -0.13 -0.30 0.22 0.10 0.13
-0.07 0.15 -0.11 -0.03 0.08 0.00 -0.07 0.07 0.00 -0.08 0.03 0.11 -0.15 0.07
-0.04 -0.03 -0.07 0.07 0.03 0.04 -0.02 -0.02 -0.05 0.00 0.00 0.00 0.05 0.02 0.02 -0.04 -0.03 -0.07 0.07 0.03 0.04
-0.02 0.02
-2.46 1.59 -0.42 -1.17 1.62 0.55 -2.17 2.31 -0.47 -1.84 -0.12 0.00 0.12 1.84 0.47 -2.31 2.17 -0.55 -1.62 1.17 0.42 -1.59 2.46
5.66 5.66 3.44 3.44 6.14 6.14 2.75 2.75 2.75 2.75 6.14 6.14 3.44 3.44 5.66 5.66
0.38 -0.38 -0.32 0.32 -0.06 0.06 1.74 -1.74 -1.74 1.74 0.06 -0.06 0.32 -0.32 -0.38 0.38
6.04 5.28 3.12 3.77 6.08 6.20 4.49 1.02 1.02 4.49 6.20 6.08 3.77 3.12 5.28 6.04
Moment Distribution for PB13
Fact.
Load
Page 26
MD
1 0.84 1.38 0.23 0.46 2.91 4.37

2 0.84 1.38 0.23 0.46 2.91 4.37
3 0.84 1.38 0.23 0.46 2.91 4.37
4 0.84 1.38 0.23 0.46 2.91 4.37

1 Beam 1 230 300 1,825 5E+08 283,562 0.39
2 Beam 2 230 300 1,825 5E+08 283,562 729,884 0.39
Col.B 250 250 2,000 3E+08 162,760 0.22
Col.T 0 0 3,000 0E+00 0 0.00

2 Beam 1 230 300 1,825 5E+08 283,562 0.39
3 Beam 2 230 300 1,825 5E+08 283,562 729,884 0.39
Col.B 250 250 2,000 3E+08 162,760 0.22
Col.T 0 0 3,000 0E+00 0 0.00

3 Beam 1 230 300 1,825 5E+08 283,562 0.39
4 Beam 2 230 300 1,825 5E+08 283,562 729,884 0.39
Col.B 250 250 2,000 3E+08 162,760 0.22
Col.T 0 0 3,000 0E+00 0 0.00
1 Mab -1.21 1.21

2 Mbc -1.21 1.21
3 Mcd -1.21 1.21
4 Mde -1.21 1.21
0.39 0.22 0.39 0.39 0.22 0.39 0.39 0.22 0.39
Page 27
MD
-1.21 1.21 -1.21 1.21 -1.21 1.21 -1.21 1.21

0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
0.00 0.00
-1.21 1.21 0.00 -1.21 1.21 0.00 -1.21 1.21 0.00 -1.21 1.21
Vertical L 3.98 3.98 3.98 3.98 3.98 3.98 3.98 3.98

Vertical L 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
Moment
Total 3.98 3.98 3.98 3.98 3.98 3.98 3.98 3.98
Load
Fact.
Load
1 0.87 1.38 0.23 0.46 2.94 4.41
2 0.87 1.38 0.23 0.46 2.94 4.41

1 Beam 1 230 300 1,850 5E+08 279,730 0.39
2 Beam 2 230 300 1,850 5E+08 279,730 722,220 0.39
Col.B 250 250 2,000 3E+08 162,760 0.23
Col.T 0 0 3,000 0E+00 0 0.00
1 Mab -1.26 1.26

2 Mbc -1.26 1.26
BEAM BEAM COLUMN BEAM BEAM
Page 28
MD
0.39 0.23 0.39

-1.26 1.26 -1.26 1.26
0.00 0.00 0.00
0.00 0.00 0.00
0.00 0.00 0.00
0.00 0.00 0.00
0.00 0.00 0.00
0.00 0.00
-1.26 1.26 0.00 -1.26 1.26
Vertical L 4.08 4.08 4.08 4.08

Vertical L 0.00 0.00 0.00 0.00
Moment
Total 4.08 4.08 4.08 4.08
Load
VERTICAL LOAD MOMENT TOTAL Working

N S W E NS WE LOAD Load
S.No.
1 5.10 4.08 9.18 6.12
2 4.80 5.00 9.80 6.53
3 5.78 5.30 6.04 17.11 11.41
4 3.73 5.54 5.44 14.71 9.81
5 1.28 2.07 3.35 2.23
6 2.8 2.07 4.87 3.25
7 10 5.7 15.70 10.47
8 6.9 5.28 3.12 15.30 10.20
9 2.44 4.08 6.52 4.34
10 3.88 3.07 3.98 10.93 7.29
11 4.16 4.05 8.21 5.48
12 3.98 3.77 6.08 13.83 9.22
13 4.03 3.58 7.61 5.07
14 4.86 6.08 6.20 17.145 11.43
15 4.9 4.75 7.29 16.95 11.30
16 3.80 3.98 3.98 11.76 7.84
Page 29
MD
17 0.00 0.00
18 0.00 0.00
19 0.00 0.00
20 4.9 4.90 3.27
21 0.00 0.00
22 0.00 0.00
23 0.00 0.00
24 0.00 0.00
25 0.00 0.00
26 0.00 0.00
27 0.00 0.00
28 0.00 0.00
29 0.00 0.00
30 0.00 0.00
31 0.00 0.00
32 0.00 0.00
33 0.00 0.00
Page 30
BEAMREIN
###
Effective Cover= 35
% steel 0 0.25 0.5 0.75 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00
Permissible S.S. 15 0 0.35 0.46 0.54 0.60 0.64 0.68 0.71 0.71 0.71 0.71 0.71 0.71
20 0 0.36 0.48 0.56 0.62 0.67 0.72 0.75 0.79 0.81 0.82 0.82 0.82
S.No.W Deff. Ml Mr Mm Tl Tr Mel Mer Mel Mer Mem %AstL %AstR %Astm AstL AstR Astm
bd^2 bd^2 bd^3 Left Right Middle Left Right Middle
Ten Com. Ten Com. Ten Com. Ten Com. Ten Com. Ten Com.
1 375 245 17 47 77 0 0 17 47 0.76 2.09 3.42 0.22 N.A. 0.67 0.00 1.18 0.26 202 ### 619 0 1088 236
2 375 245 20 50 80 0 0 20 50 0.89 2.22 3.55 0.26 N.A. 0.73 0.00 1.23 0.31 239 ### 667 0 1131 284
3 375 245 23 53 83 0 0 23 53 1.02 2.35 3.69 0.30 N.A. 0.78 0.00 1.28 0.36 278 ### 716 0 1173 332
4 375 245 26 56 86 0 0 26 56 1.16 2.49 3.82 0.34 N.A. 0.83 0.00 1.32 0.41 317 ### 767 0 1215 379
5 375 245 29 59 89 0 0 29 59 1.29 2.62 3.95 0.39 N.A. 0.89 0.21 1.37 0.47 357 ### 821 196 1258 427
6 375 245 32 62 92 32 62 1.42 2.75 4.09 0.43 N.A. 0.95 0.00 1.42 0.52 398 ### 872 0 1301 475
7 375 245 35 65 95 35 65 1.55 2.89 4.22 0.48 N.A. 1.00 0.04 1.46 0.57 440 ### 918 34 1343 523
8 375 245 38 68 98 38 68 1.69 3.02 4.35 0.53 N.A. 1.05 0.10 1.51 0.62 483 ### 961 93 1385 571
9 375 245 41 71 101 41 71 1.82 3.15 4.49 0.57 N.A. 1.09 0.15 1.55 0.67 527 ### 1003 141 1427 619
10 375 245 44 74 104 44 74 1.95 3.29 4.62 0.62 N.A. 1.14 0.21 1.60 0.73 572 ### 1045 188 1470 667
11 230 295 0 0 0.00 0.00 0.00 #N/A N.A. #N/A N.A. #N/A N.A. #N/A ### #N/A ### #N/A ###
Page 31
BEAMREIN
Sl Sr SsL SsR ScL ScR Vul Vur VuL VuR Stirrups

d d Left R Left R Left R
8 8 10 10 12 12
1 50 65 0.32 0.54 29 49 21 16 1.17 1.55 184 184 184 184 184 184
2 55 66 0.37 0.55 34 51 21 15 1.14 1.61 184 184 184 184 184 184
3 60 67 0.39 0.57 35 52 25 15 1.00 1.64 184 184 184 184 184 184
4 45 50 0.41 0.58 37 53 8 -3 3.17 -7.37 184 #N/A 184 #N/A 184 #N/A
5 100 110 0.43 0.59 39 55 61 55 0.40 0.44 140 160 184 184 184 184
6 75 70 0.45 0.61 41 56 34 14 0.72 1.73 184 184 184 184 184 184
7 80 71 0.47 0.62 43 57 37 14 0.67 1.74 184 184 184 184 184 184
8 85 72 0.49 0.63 45 58 40 14 0.61 1.73 184 184 184 184 184 184
9 90 73 0.50 0.64 46 59 44 14 0.56 1.71 184 184 184 184 184 184
10 95 74 0.52 0.65 48 59 47 15 0.52 1.69 180 184 184 184 184 184
11 30 105 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
Page 32
BEAMREIN
M %As %As Spacing of Stirrups

bd^2 15 20 Dia Spa- Dia Spa- Dia Spa-
0.30 0.085 0.085 of cing of cing of cing
0.34 0.097 0.097 Bar Bar Bar
0.38 0.109 0.108
0.42 0.120 0.120 8 10 12
0.46 0.132 0.131 0.138 50 0.088 50 0.061 50
0.50 0.144 0.143 0.165 60 0.106 60 0.073 60
0.54 0.156 0.155 0.193 70 0.123 70 0.086 70
0.58 0.169 0.167 0.220 80 0.141 80 0.098 80
0.62 0.181 0.179 0.248 90 0.159 90 0.110 90
0.66 0.194 0.191 0.275 100 0.176 100 0.122 100
0.70 0.206 0.203 0.303 110 0.194 110 0.135 110
0.74 0.219 0.215 0.331 120 0.212 120 0.147 120
0.78 0.232 0.227 0.358 130 0.229 130 0.159 130
0.82 0.244 0.240 0.386 140 0.247 140 0.171 140
0.86 0.257 0.252 0.413 150 0.264 150 0.184 150
0.90 0.270 0.264 0.441 160 0.282 160 0.196 160
0.94 0.283 0.277 0.468 170 0.300 170 0.208 170
0.98 0.296 0.289 0.496 180 0.317 180 0.220 180
1.02 0.309 0.302 0.524 190 0.335 190 0.233 190
1.06 0.323 0.314 0.551 200 0.353 200 0.245 200
1.10 0.336 0.327 0.689 250 0.441 250 0.306 250
1.14 0.350 0.340 0.826 300 0.529 300 0.367 300
1.18 0.364 0.353 0.964 350 0.617 350 0.429 350
1.22 0.378 0.366 1.103 400 0.705 400 0.490 400
1.26 0.392 0.379 1.239 450 0.794 450 0.551 450
1.30 0.406 0.392
1.34 0.420 0.406
1.38 0.435 0.419
1.42 0.450 0.433
1.46 0.465 0.446
1.50 0.480 0.460
Page 33
BEAMREIN
1.54 0.495 0.474

1.58 0.510 0.488
1.62 0.526 0.502
1.66 0.542 0.516
1.70 0.558 0.530
1.74 0.574 0.544
1.78 0.590 0.559
1.82 0.607 0.573
1.86 0.624 0.588
1.90 0.641 0.602
1.94 0.658 0.617
1.98 0.676 0.632
2.02 0.693 0.648
2.06 0.712 0.663
2.10 0.727 0.678 0.011
2.14 0.741 0.694 0.027
2.18 0.755 0.710 0.042
2.22 0.768 0.725 0.058
2.26 0.782 0.741 0.073
2.30 0.796 0.757 0.089
2.34 0.810 0.774 0.104
2.38 0.824 0.790 0.120
2.42 0.837 0.807 0.135
2.46 0.851 0.823 0.151
2.50 0.865 0.840 0.166
2.54 0.879 0.858 0.182
2.58 0.893 0.875 0.197
2.62 0.907 0.893 0.213
2.66 0.921 0.910 0.228
2.70 0.935 0.928 0.244
2.74 0.949 0.943 0.259
2.78 0.963 0.958 0.275
2.82 0.976 0.974 0.290
2.86 0.990 0.989 0.306
2.90 1.004 1.004 0.321 0.054
Page 34
BEAMREIN
2.94 1.018 1.018 0.337 0.070

2.98 1.032 1.032 0.352 0.085
3.02 1.045 1.045 0.368 0.101
3.06 1.059 1.059 0.383 0.116
3.10 1.073 1.073 0.399 0.132
3.14 1.087 1.087 0.414 0.148
3.18 1.101 1.101 0.430 0.163
3.22 1.114 1.114 0.445 0.179
3.26 1.128 1.128 0.461 0.194
3.30 1.142 1.142 0.476 0.210
3.34 1.156 1.156 0.492 0.226
3.38 1.170 1.170 0.507 0.241
3.42 1.184 1.184 0.523 0.257
3.46 1.198 1.198 0.538 0.272
3.50 1.212 1.212 0.554 0.288
3.54 1.226 1.226 0.569 0.304
3.58 1.240 1.240 0.585 0.319
3.62 1.253 1.253 0.600 0.335
3.66 1.267 1.267 0.616 0.350
3.70 1.281 1.281 0.631 0.366
3.74 1.295 1.295 0.647 0.382
3.78 1.309 1.309 0.662 0.397
3.82 1.322 1.322 0.678 0.413
3.86 1.336 1.336 0.693 0.428
3.90 1.350 1.350 0.709 0.444
3.94 1.364 1.364 0.725 0.460
3.98 1.378 1.378 0.740 0.475
4.02 1.392 1.392 0.756 0.491
4.06 1.406 1.406 0.771 0.506
4.10 1.420 1.420 0.787 0.522
4.14 1.434 1.434 0.802 0.538
4.18 1.448 1.448 0.818 0.553
4.22 1.461 1.461 0.833 0.569
4.26 1.475 1.475 0.849 0.584
4.30 1.489 1.489 0.864 0.600
Page 35
BEAMREIN
4.34 1.503 1.503 0.880 0.616

4.38 1.517 1.517 0.895 0.632
4.42 1.530 1.530 0.911 0.647
4.46 1.544 1.544 0.926 0.663
4.50 1.558 1.558 0.942 0.679
4.54 1.572 1.572 0.957 0.695
4.58 1.586 1.586 0.973 0.710
4.62 1.599 1.599 0.988 0.726
4.66 1.613 1.613 1.004 0.741
4.70 1.627 1.627 1.019 0.757
4.74 1.641 1.641 1.035 0.773
4.78 1.655 1.655 1.050 0.788
4.82 1.669 1.668 1.066 0.804
4.86 1.683 1.682 1.081 0.819
4.90 1.697 1.696 1.097 0.835
4.94 1.711 1.710 1.112 0.851
4.98 1.725 1.724 1.128 0.866
5.02 1.738 1.738 1.143 0.882
5.06 1.752 1.752 1.159 0.897
5.10 1.766 1.766 1.174 0.913
5.14 1.780 1.780 1.190 0.929
5.18 1.794 1.794 1.205 0.944
5.22 1.807 1.807 1.221 0.960
5.26 1.821 1.821 1.236 0.975
5.30 1.835 1.835 1.252 0.991
5.34 1.849 1.849 1.267 1.007
5.38 1.863 1.863 1.283 1.022
5.42 1.877 1.877 1.298 1.038
5.46 1.891 1.891 1.314 1.053
5.50 1.905 1.905 1.329 1.069
5.54 1.919 1.919 1.345 1.085
5.58 1.933 1.933 1.360 1.100
5.62 1.946 1.946 1.376 1.116
5.66 1.960 1.960 1.391 1.131
5.70 1.974 1.974 1.407 1.147
Page 36
BEAMREIN
5.74 1.988 1.988 1.423 1.163

5.78 2.002 2.002 1.438 1.178
5.82 2.015 2.015 1.454 1.194
5.86 2.029 2.029 1.469 1.209
5.90 2.043 2.043 1.485 1.225
5.94 2.057 2.057 1.500 1.241
5.98 2.071 2.071 1.516 1.256
6.02 2.084 2.084 1.531 1.272
6.06 2.098 2.098 1.547 1.287
6.10 2.112 2.112 1.562 1.303
6.14 2.126 2.126 1.578 1.319
6.18 2.140 2.140 1.593 1.334
6.22 2.154 2.153 1.609 1.350
6.26 2.168 2.167 1.624 1.365
6.30 2.182 2.181 1.640 1.381
6.34 2.196 2.195 1.655 1.397
6.38 2.209 2.209 1.670 1.413
6.42 2.223 1.428
6.46 2.237 1.444
6.50 2.251 1.460
6.54 2.265 1.476
6.58 2.279 1.491
6.62 2.292 1.507
6.66 2.306 1.522
6.70 2.320 1.538
6.74 2.334 1.554
6.78 2.348 1.569
6.82 2.361 1.585
6.86 2.375 1.600
6.90 2.389 1.616
6.94 2.403 1.632
6.98 2.417 1.647
7.02 2.431 1.663
7.06 2.445 1.678
7.10 2.459 1.694
Page 37
COLUMNTREIN
Dia. of bar = 25
S. Size Gr. Rec OneEff. Eff Axial Factored Factored Factored Factored lex ley Addi-
No. of M d' =1 =1 Lex Ley Load Moment Moment Moment Moment D D tional
Col. b Cir Eq. M M Pu Longer Longer Shorter Shorter Moment
D mm mm =2 =2 Top Bottom Top Bottom Max
1 250 250 20 53 1 2 2 2 221 5.5 0 5.5 0 8 8.0 1.768
2 250 250 20 53 2 1 2 2 221 5.5 0 5.5 0 8 8.0 1.768
3 410 310 20 53 1 2 6.2 5.2 1520 42 24.5 32 22 15 16.8 71.255
4 415 315 20 53 1 2 6.3 5.3 1530 43 25.5 33 23 15 16.8 73.163
5 420 320 20 53 1 2 6.4 5.4 1540 44 26.5 34 24 15 16.9 75.093
6 425 325 20 53 1 2 6.5 5.5 1550 45 27.5 35 25 15 16.9 77.044
7 430 330 20 53 1 2 6.6 5.6 1560 46 28.5 36 26 15 17.0 79.016
8 435 335 20 53 1 2 6.7 5.7 1570 47 29.5 37 27 15 17.0 81.008
9 440 340 20 53 1 2 6.8 5.8 1580 48 30.5 38 28 15 17.1 83.022
10 445 345 20 53 1 2 6.9 5.9 1590 49 31.5 39 29 16 17.1 85.056
11 450 350 20 53 1 2 7 6 1600 50 32.5 40 30 16 17.1 87.111
12 455 355 20 53 1 2 7.1 6.1 1610 51 33.5 41 31 16 17.2 89.187
13 460 360 20 53 1 2 7.2 6.2 1620 52 34.5 42 32 16 17.2 91.283
14 465 365 20 53 1 2 7.3 6.3 1630 53 35.5 43 33 16 17.3 93.401
15 470 370 20 53 1 2 7.4 6.4 1640 54 36.5 44 34 16 17.3 95.539
16 475 375 20 53 1 2 7.5 6.5 1650 55 37.5 45 35 16 17.3 97.697
17 480 380 20 53 1 2 7.6 6.6 1660 56 38.5 46 36 16 17.4 99.877
18 485 385 20 53 1 2 7.7 6.7 1670 57 39.5 47 37 16 17.4 102.08
19 490 390 20 53 1 2 7.8 6.8 1680 58 40.5 48 38 16 17.4 104.3
20 495 395 20 53 1 2 7.9 6.9 1690 59 41.5 49 39 16 17.5 106.54
21 500 400 20 53 1 2 8 7 1700 60 42.5 50 40 16 17.5 108.8
22 505 405 20 53 1 2 8.1 7.1 1710 61 43.5 51 41 16 17.5 111.08
23 510 410 20 53 1 2 8.2 7.2 1720 62 44.5 52 42 16 17.6 113.39
24 515 415 20 53 1 2 8.3 7.3 1730 63 45.5 53 43 16 17.6 115.71
25 520 420 20 53 1 2 8.4 7.4 1740 64 46.5 54 44 16 17.6 118.05
26 525 425 20 53 1 2 8.5 7.5 1750 65 47.5 55 45 16 17.6 120.42
27 530 430 20 53 1 2 8.6 7.6 1760 66 48.5 56 46 16 17.7 122.8
28 535 435 20 53 1 2 8.7 7.7 1770 67 49.5 57 47 16 17.7 125.21
29 540 440 20 53 1 2 8.8 7.8 1780 68 50.5 58 48 16 17.7 127.63
30 545 445 20 53 1 2 8.9 7.9 1790 69 51.5 59 49 16 17.8 130.08
31 550 450 20 53 1 2 9 8 1800 70 52.5 60 50 16 17.8 132.55
32 555 455 20 53 1 2 9.1 8.1 1810 71 53.5 61 51 16 17.8 135.03
33 560 460 20 53 1 2 9.2 8.2 1820 72 54.5 62 52 16 17.8 137.54
34 565 465 20 53 1 2 9.3 8.3 1830 73 55.5 63 53 16 17.8 140.07
35 570 470 20 53 1 2 9.4 8.4 1840 74 56.5 64 54 16 17.9 142.62
Page 38
COLUMNTREIN
Cover for colu = 40 Eff.Cover 53 Mux Muy

Addi- % Ag Puz Pbx Pbx kx ky Max May Applicable for ex
tional Steel KN Braced Column
Moment Trial & No horizon
May mm^2 loads
1.768 1 6E+04 12 750 0.21 0.21 232 232 1.02 1.02 1.80 1.80 2.00
1.768 1 6E+04 12 750 0.21 0.21 175 175 0.92 0.92 1.63 1.63 2.00
66.292 2.05 1E+05 15.2 1926 0.13 0.17 551 475 0.30 0.28 21.03 18.53 2.61
68.219 2.1 1E+05 15.3 2000 0.13 0.17 568 489 0.33 0.31 24.02 21.22 2.64
70.166 2.15 1E+05 15.5 2076 0.13 0.16 586 503 0.36 0.34 27.02 23.92 2.68
72.135 2.2 1E+05 15.6 2155 0.12 0.16 603 517 0.39 0.37 30.03 26.63 2.72
74.124 2.25 1E+05 15.8 2235 0.12 0.16 621 531 0.42 0.40 33.04 29.36 2.75
76.133 2.3 1E+05 15.9 2317 0.12 0.16 639 546 0.45 0.42 36.07 32.11 2.79
78.164 2.35 1E+05 16.1 2401 0.12 0.15 658 560 0.47 0.45 39.10 34.87 2.83
80.214 2.4 2E+05 16.2 2487 0.12 0.15 677 575 0.50 0.47 42.15 37.64 2.86
82.286 2.45 2E+05 16.4 2575 0.12 0.15 696 590 0.52 0.49 45.20 40.43 2.90
84.378 2.5 2E+05 16.5 2665 0.12 0.15 715 715 0.54 0.54 48.26 45.66 2.94
86.49 2.55 2E+05 16.7 2757 0.11 0.15 735 735 0.56 0.56 51.33 48.64 2.97
88.623 2.6 2E+05 16.8 2851 0.11 0.14 755 755 0.58 0.58 54.41 51.63 3.01
90.776 2.65 2E+05 17 2948 0.11 0.14 775 775 0.60 0.60 57.51 54.64 3.05
92.95 2.7 2E+05 17.1 3046 0.11 0.14 796 796 0.62 0.62 60.61 57.67 3.08
95.144 2.75 2E+05 17.3 3146 0.11 0.14 817 817 0.64 0.64 63.73 60.71 3.12
97.359 2.8 2E+05 17.4 3249 0.11 0.14 838 838 0.65 0.65 66.85 63.76 3.16
99.594 2.85 2E+05 17.6 3354 0.11 0.13 860 860 0.67 0.67 69.99 66.84 3.19
101.85 2.9 2E+05 17.7 3461 0.11 0.13 882 882 0.69 0.69 73.14 69.93 3.23
104.13 2.95 2E+05 17.9 3570 0.11 0.13 904 904 0.70 0.70 76.31 73.03 3.27
106.42 3 2E+05 18 3681 0.10 0.13 926 926 0.72 0.72 79.48 76.15 3.30
108.74 3.05 2E+05 18.2 3795 0.10 0.13 949 949 0.73 0.73 82.67 79.29 3.34
111.07 3.1 2E+05 18.3 3911 0.10 0.13 972 972 0.74 0.74 85.88 82.44 3.38
113.43 3.15 2E+05 18.5 4029 0.10 0.13 996 996 0.75 0.75 89.09 85.60 3.41
115.81 3.2 2E+05 18.6 4150 0.10 0.12 1020 1020 0.77 0.77 92.32 88.79 3.45
118.21 3.25 2E+05 18.8 4273 0.10 0.12 1186 1044 0.81 0.78 99.98 91.99 3.49
120.62 3.3 2E+05 18.9 4399 0.10 0.12 1215 1068 0.83 0.79 103.39 95.20 3.52
123.06 3.35 2E+05 19.1 4526 0.10 0.12 1245 1093 0.84 0.80 106.81 98.44 3.56
125.52 3.4 2E+05 19.2 4656 0.10 0.12 1275 1118 0.85 0.81 110.25 101.69 3.60
128 3.45 2E+05 19.4 4789 0.10 0.12 1305 1144 0.86 0.82 113.71 104.95 3.63
130.5 3.5 3E+05 19.5 4924 0.09 0.12 1335 1169 0.87 0.83 117.17 108.23 3.67
133.02 3.55 3E+05 19.7 5062 0.09 0.11 1366 1195 0.88 0.84 120.66 111.53 3.71
135.56 3.6 3E+05 19.8 5202 0.09 0.11 1398 1222 0.89 0.85 124.16 114.85 3.74
138.12 3.65 3E+05 20 5345 0.09 0.11 1430 1249 0.90 0.86 127.67 118.18 3.78
Page 39
COLUMNTREIN
ey Mux Muy Design Pu p/fck from Mux1 from Muy1 Mux Muy Pu
Moment fck b D chart chart Mux1 Muy1 Puz
Sq.cms
2.00 4.42 4.42 6.2 6.2 0.18 0.05 0.09 28.1 0.09 28.1 0.22 0.22 0.29 6
2.00 4.42 4.42 6.0 6.0 0.18 0.05 0.055 17.2 0.11 34.4 0.35 0.18 0.29 6
2.07 39.62 31.515 60.6 50.0 0.60 0.10 0.116 120.9 0.12 97.7 0.50 0.51 0.79 26
2.11 40.44 32.283 64.5 53.5 0.59 0.11 0.122 132.4 0.14 113.7 0.49 0.47 0.76 27
2.15 41.27 33.059 68.3 57.0 0.57 0.11 0.128 144.5 0.15 130.7 0.47 0.44 0.74 29
2.18 42.11 33.842 72.1 60.5 0.56 0.11 0.134 157.3 0.17 149.0 0.46 0.41 0.72 30
2.22 42.95 34.632 76.0 64.0 0.55 0.11 0.14 170.8 0.18 168.6 0.44 0.38 0.70 32
2.26 43.8 35.43 79.9 67.5 0.54 0.12 0.146 185.1 0.19 189.4 0.43 0.36 0.68 34
2.29 44.66 36.235 83.8 71.1 0.53 0.12 0.152 200.1 0.21 211.6 0.42 0.34 0.66 35
2.33 45.53 37.047 87.7 74.7 0.52 0.12 0.158 215.9 0.22 235.2 0.41 0.32 0.64 37
2.37 46.4 37.867 91.6 78.3 0.51 0.12 0.164 232.5 0.24 260.2 0.39 0.30 0.62 39
2.40 47.28 38.694 95.5 84.4 0.50 0.13 0.17 249.9 0.25 286.7 0.38 0.29 0.60 40
2.44 48.17 39.528 99.5 88.2 0.49 0.13 0.176 268.1 0.26 314.8 0.37 0.28 0.59 42
2.48 49.06 40.37 103.5 92.0 0.48 0.13 0.182 287.3 0.28 344.4 0.36 0.27 0.57 44
2.51 49.97 41.219 107.5 95.9 0.47 0.13 0.188 307.3 0.29 375.8 0.35 0.26 0.56 46
2.55 50.88 42.075 111.5 99.7 0.46 0.14 0.194 328.3 0.31 408.8 0.34 0.24 0.54 48
2.59 51.79 42.939 115.5 103.6 0.46 0.14 0.2 350.2 0.32 443.6 0.33 0.23 0.53 50
2.62 52.72 43.81 119.6 107.6 0.45 0.14 0.206 373.1 0.33 480.2 0.32 0.22 0.51 52
2.66 53.65 44.688 123.6 111.5 0.44 0.14 0.212 397.0 0.35 518.7 0.31 0.21 0.50 54
2.70 54.59 45.574 127.7 115.5 0.43 0.15 0.218 422.0 0.36 559.2 0.30 0.21 0.49 57
2.73 55.53 46.467 131.8 119.5 0.43 0.15 0.224 448.0 0.38 601.6 0.29 0.20 0.48 59
2.77 56.49 47.367 136.0 123.5 0.42 0.15 0.23 475.1 0.39 646.1 0.29 0.19 0.46 61
2.81 57.45 48.275 140.1 127.6 0.41 0.15 0.236 503.3 0.40 692.7 0.28 0.18 0.45 64
2.84 58.42 49.19 144.3 131.6 0.40 0.16 0.242 532.7 0.42 741.5 0.27 0.18 0.44 66
2.88 59.39 50.112 148.5 135.7 0.40 0.16 0.248 563.3 0.43 792.5 0.26 0.17 0.43 69
2.92 60.38 51.042 152.7 139.8 0.39 0.16 0.254 595.1 0.45 845.9 0.26 0.17 0.42 71
2.95 61.37 51.979 161.3 144.0 0.39 0.16 0.26 628.1 0.46 901.6 0.26 0.16 0.41 74
2.99 62.36 52.923 165.8 148.1 0.38 0.17 0.266 662.4 0.47 959.7 0.25 0.15 0.40 77
3.03 63.37 53.875 170.2 152.3 0.37 0.17 0.272 698.0 0.49 1020.3 0.24 0.15 0.39 80
3.06 64.38 54.834 174.6 156.5 0.37 0.17 0.278 734.9 0.50 1083.6 0.24 0.14 0.38 82
3.10 65.4 55.8 179.1 160.8 0.36 0.17 0.284 773.2 0.52 1149.4 0.23 0.14 0.38 85
3.14 66.43 56.774 183.6 165.0 0.36 0.18 0.29 812.9 0.53 1217.9 0.23 0.14 0.37 88
3.17 67.46 57.755 188.1 169.3 0.35 0.18 0.296 854.0 0.54 1289.2 0.22 0.13 0.36 91
3.21 68.5 58.743 192.7 173.6 0.35 0.18 0.302 896.6 0.56 1363.4 0.21 0.13 0.35 95
3.25 69.55 59.739 197.2 177.9 0.34 0.18 0.308 940.7 0.57 1440.4 0.21 0.12 0.34 98
Page 40
COLUMNTREIN
%steel M15 M20 k1 0.05 0.1 0.15 0.2

Sq.cms 1 9.6 12 Rect. 0.219 0.207 0.196 0.184
2 12.5 15 Circular 0.172 0.16 0.149 0.138
3 15.5 18 2 side Eq. 0.096 0.082 0.046 -0.022
4 18.5 21 4 side Eq. 0.424 0.328 0.203 0.028
Circular 0.41 0.323 0.201 0.036
Page 41

BLDG

Uploaded by

Document Informationclick to expand document informationbldg

Document Informationclick to expand document information

Copyright:

Available Formats

BLDG

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BLDG

Uploaded by

Copyright:

Available Formats

INFO

20 For Simply supported slab Maximum moment calculated by weight of slab /

Column shape if Rectangular = 1 = 1 % Ast Span/Deff.

DESIGN OF CANTILEVER ROOF SLAB

Distribution Steel 0.12 0.12 0.12

DESIGN OF ROOF SLAB

Distribution Steel 0.12 0.12 0.12

DESIGN OF ROOF SLAB

DESIGN OF ROOF SLAB

Coeff. Moment Coeff. Momen Coeff. Moment Coeff. Moment

1.80 1.9 1.80 1.9

% steel 0.30 0.22 0.16 0.135

Check for Serviceability O.K. O.K. O.K. O.K.

Distribution Steel 0.12

Design moment Short Span Long Span

Eff. depth provided 91 91 91 91

S. No. D.L. L.L. Span D.L. L.L. W.L. TOTAL

TWO-WAY SLAB ROOF LOAD

Short Span 1.5 1.5 9000 5000 2.50 2.50 13.11

MOMENT DISTRIBUTION FOR PB1

Slab Wall Self Wt. Others Total Fact.

Width Depth LengthMoment oStiffness Total Distribution

Distribution factor for two span

Width Depth LengthMoment oStiffness Total Distribution

Distribution factor for two span

Width Depth LengthMoment oStiffness Total Distribution

1 Mab -1.85 1.85

0.37 0.26 0.37 0.40 0.28 0.32 0.26 0.23 0.52

Vertical L 5.05 5.05 5.05 5.05 5.66 5.66 2.51 2.51

MOMENT DISTRIBUTION FOR PB4/PB7

Width Depth LengthMoment oStiffness Total Distribution

Distribution factor for two span

Width Depth LengthMoment oStiffness Total Distribution

1 Mab -0.55 0.55

BEAM BEAM COLUMN BEAM BEAM COLUMN BEAM BEAM

0.47 0.18 0.35 0.40 0.20 0.40

Vertical L 2.75 2.75 4.02 4.02 4.02 4.02

MOMENT DISTRIBUTION FOR PB5

Width Depth LengthMoment oStiffness Total Distribution

Col.B 250 250 2,000 3E+08 162,760 0.20

Distribution factor for two span

Width Depth LengthMoment oStiffness Total Distribution

1 Mab -1.00 1.00

BEAM BEAM COLUMN BEAM BEAM COLUMN BEAM BEAM

0.40 0.20 0.40 0.45 0.23 0.32

Vertical L 3.73 3.73 3.73 3.73 4.64 4.64

Total 3.80 3.67 3.45 4.01 4.47 4.81

MOMENT DISTRIBUTION FOR PB8

Width Depth LengthMoment oStiffness Total Distribution

Distribution factor for two span

Width Depth LengthMoment oStiffness Total Distribution

Distribution factor for two span

Width Depth LengthMoment oStiffness Total Distribution

1 Mab -1.88 1.88

0.37 0.26 0.37 0.40 0.28 0.32 0.26 0.23 0.52

Vertical L 5.13 5.13 5.13 5.13 5.65 5.65 3.77 3.77

1 0.80 1.38 0.23 0.46 2.87 4.31