Preface

Foreword

These instructions are intended to help perform repairs properly on the engine described here.
The illustrations and associated descriptions are typical for the current state of development.
Please note that all work in these repair instructions was performed with the engine removed.
The expert technical knowledge required for handling gas engines has been assumed in creation of this
publication.
Repairs to drive units are to be performed by our customer service or the customer service of the manufac-
turer.

Note:
Only use fuel, coolants and lubricants in accordance with MAN’s regulations otherwise the manu-
facturer’s warranty will not apply!
For basic information on the fuels see the publication “Fuels, Lubricants and Coolants for MAN
Diesel Engines”.
You can find the approved products in the internet under:
http://www.man-mn.com/ " Products & Solutions " E-Business

Yours sincerely
MAN Nutzfahrzeuge Aktiengesellschaft
Werk Nürnberg

The right to make technical changes resulting from further development is reserved.

© 2006 MAN Nutzfahrzeuge Aktiengesellschaft

Reproduction, duplication or translation, also of excerpts, is not permitted without written permission of
MAN. All rights in accordance with copyright law are expressly reserved by MAN.

MTDA Technical status: 03.2006 51.99598−8018

1
 Instructions

Important instructions which concern technical safety and protection of persons are emphasised as shown
below.

Danger:
This refers to working and operating procedures which must be complied with in order to rule out
the risk to persons.

Caution:
This refers to working and operating procedures which must be complied with in order to prevent
damage to or destruction of material.

Note:
Explanatory descriptions which help in understanding the relevant work or operating procedure to
be carried out.

Assembly of pipes

Danger:
No pipes may be bent.
Risk of breakage!

Fitting flat seals / gaskets

Flat seals / gaskets are often inserted with sealing agents or adhesives to make fitting them easier or to
achieve better sealing. Flat seals may slip in operation due to the “sewing -machine” effect, in particular if
they are used between parts with different rates of linear expansion under heat (e.g. aluminium and cast
iron), and leaks may then occur.

Example:
The cap of the front crankshaft seal. If a sealing agent or an adhesive is used here the flat seal will move
inwards in the course of time as a result of the different expansion rates of the materials. Oil will be lost, for
which the shaft seal may be thought to be responsible.

Flat seals / gaskets can be fitted properly only if the following points are observed:
D Use only genuine MAN seals / gaskets
D The sealing faces must be undamaged and clean
D Do not use any sealing agent or adhesive − as an aid to fitting the seals a little grease can be used if
necessary so that the seal will stick to the part to be fitted
D Tighten bolts evenly to the specified torque

Fitting round sealing rings

D Use only genuine MAN round sealing rings
D The sealing faces must be undamaged and clean
D Always wet round sealing rings with engine oil before fitting them

2
 Contents

Page
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Engine type classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Fault table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
General notes on engine overhaul . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Illustrations of E 2842 E 302 engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Engine lubrication diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Cooling system diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Engine timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Ignition
Microprocessor-controlled ignition system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Replacing spark plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Checking and setting ignition timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Cooling
Draining and filling with coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Lubrication
Changing oil filter cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Removing and installing oil cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Removing and installing oil pump, servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Oil injection nozzle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Flywheel / crankshaft sealing
Removing and fitting vibration damper, replacing front crankshaft gasket . . . . . . . . . . . . . . . . . . . . . . 36
Removing and installing flywheel, replacing gear ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Removing and installing crankshaft seal (flywheel end) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Replacing bearing race . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Crankshaft seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Intake and exhaust system
Removing and installing intake manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Removing and installing exhaust manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Cylinder head
Removing and installing cylinder head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Setting valve clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Dismantling and assembling rocker arm mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Removing and installing valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Checking compression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Valve timing
Removing and installing timing case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Removing and installing camshaft, replacing camshaft bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Checking valve timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

3
 Contents

Page
Crankgear, pistons
Removing and installing crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Removing and installing pistons with conrods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Removing pistons from conrod and fitting, checking − replacing conrod . . . . . . . . . . . . . . . . . . . . . . . 70
Removing and installing piston rings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Replacing cylinder liners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Measuring piston recess under crankcase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Attachments
Removing and installing starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
“Active” impulse sensor for IC 500 ignition system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
“Passive” impulse sensor (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Service Data
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Crankcase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Cylinder liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Flywheel and starter gear ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Conrods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Pistons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Cylinder head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Valve gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Engine lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Ignition system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Ignition timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Cylinder-head bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Torque guide values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Special tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

4
 Engine type classification

The type designation, consisting of a sequence of letters and numbers, indicates some characteristics of
each engine, provided you are familiar with the basic terminology.
The system is explained here using the type E 2842 E 302 as an example:

E The “E” at the start of the type designation stands for natural gas (German: Erdgas)

28 The numbers “28” indicate that this is a power unit with 128 mm bore

4 The “4” means 142 mm stroke

2 The “2” indicates the number of cylinders 12

E The “E” stands for “fitted engine” (German: Einbaumotor) and is intended to distinguish
MAN vehicle engines

302 This is a factory-internal development number

5
 Safety regulations

General
Important safety regulations are summarized in this quick-reference overview and arranged by topic to ef-
fectively convey the knowledge necessary to avoid accidents causing injury, damage or environmental haz-
ard. Additional information can be found in the operating instructions of the engine.

Important:
Should an accident occur despite all precautionary measures, particularly one involving contact with corros-
ive acid, penetration of fuel under the skin, scalding by hot oil, antifreeze splashing into the eyes etc. you
must seek medical assistance immediately.

1. Regulations for the prevention of accidents with personal injury

Inspection, adjustment and repair work may only be performed by authorised and skilled person-
nel.

D The engine may only be started and operated by authorised personnel.

D When the engine is running, do not get too close to the rotating parts.
Wear close-fitting clothing.

D Do not touch hot engine with bare hands: Risk of burns.

ËË
D Keep area surrounding engine, ladders and stairways free of oil and grease. Accidents
caused by slipping can have serious consequences.
D Only work with tools which are in good condition. Worn spanners/wrenches slip: Danger
of injury.
D Persons must not stand under an engine suspended on a crane hook. Keep lifting gear
in order.

D Open the coolant circuit only when the engine has cooled down. If it is unavoidable that
the circuit be opened with the engine at operating temperature, observe the instructions
in the chapter “Maintenance and care” in the operating instructions.
D Do not tighten or undo pipes and hoses under pressure (lubricating oil circuit, coolant
circuit and any downstream hydraulic oil circuits). The fluids which flow out can cause
injury.

6
 Safety regulations

D When working on the electrical system, first disconnect the earth cable of the battery
and reconnect this last to prevent short circuits.

D Follow the manufacturer’s instructions for handling batteries.

Caution:
Accumulator acid is toxic and caustic. Battery gases are explosive.

D When performing welding work, observe the “Notes for welders”.

7
 Safety regulations

2. Regulations for the prevention of engine damage and premature wear

D The engine must be cleaned thoroughly prior to repair. Ensure that during repair work no dirt,
sand or foreign bodies enter the engine.

D If engine operation is disrupted, immediately determine the cause and have it remedied to prevent addi-
tional damage.

D In every case, use only original MAN spare parts. The installation of parts that are “just as good” but do
not originate from MAN can under certain circumstances cause severe damage − for which the work-
shop performing the repair must bear responsibility.

D Never allow the engine to run dry, i.e. without lubricant or coolant.
Appropriate notices must be attached to engines that are not ready for operation.

D Only use lubricants, fluids and fuel approved by MAN (gas, engine oil, antifreeze and corrosion protec-
tion agents). Pay attention to cleanliness.

D Do not fill engine oil beyond the max. notch on the dipstick. Do not exceed the maximum per-
missible tilt of the engine.
Serious damage to the engine may result if these instructions are not adhered to.

D Control and monitoring devices (charge control, oil pressure, coolant temperature) must be in perfect
working order.

3. Safety instructions for handling the ignition system

D When the engine is in operation, the following parts of the ignition system must not be
touched or disconnected under any circumstances:
− Ignition coils and caps
− Cables of the high-voltage circuit
− Cables of the low-voltage circuit
− Plugs of the output and input wiring harness

D For all work related to set-up, operation, conversion, customisation, maintenance and
repairs, the power must be disconnected from the ignition system and secured against
inadvertent reactivation.

8
 Safety regulations

4. Regulations for the prevention of environmental damage

Engine oil and filter cartridges

D Old oil must be passed on for recycling.

D Take extreme care that no oil enters the waste water system or seeps into the ground.
Caution:The drinking water supply could be contaminated.

D Filter elements are classed as dangerous waste and must be treated as such.

Coolant

D Treat undiluted corrosion protection agents and / or antifreeze as hazardous waste.

D When disposing of used coolant, the regulations issued by the relevant local authorities must be ob-
served.

5. Instructions for handling used engine oil ∗

Prolonged or repeated contact between the skin and any kind of engine oil decreases the skin. Drying, ir-
ritation or inflammation of the skin may therefore occur. Used engine oil also contains hazardous sub-
stances that have caused skin cancer in tests on animals. If the basic principles of work safety and hygiene
are observed, handling used engine oil does not represent a health hazard.

Precautionary measures to protect your health:

D Avoid prolonged or repeated skin contact with used engine oil.
D Protect your skin by means of suitable agents (creams etc.) or wear protective gloves.
D Clean skin which has been in contact with engine oil.
− Wash thoroughly with soap and water. A nail brush provides effective assistance here.
− Special hand cleaning agents make it easier to clean dirty hands.
− Do not use petrol (gasoline), diesel fuel, gas oil or solvents as washing agents.
D After washing apply a fatty skin cream to the skin.
D Change clothing and shoes that are soaked in oil.
D Do no put oily cloths in you pockets.

Ensure that used engine oil is disposed of in the appropriate manner.

− Engine oil is a substance that endangers the water supply −

For this reason do not let engine oil get into the ground, waterways, the drains or the sewers. Violations are
punishable.

Carefully collect and dispose of used engine oil. Information on collection points can be obtained from sales
personnel, the supplier or the local authorities.

∗ Based on “Information sheet for handling used engine oil”.

9
 Safety regulations

6. Safety instructions for handling gaseous fuels

Gaseous fuels consist essentially of methane, propane and butane as well as traces of higher hy-
drocarbons and inert components such as carbon dioxide and nitrogen.

D The regulations applicable to gas installations must be observed.

D Exhaust gases are toxic. Comply with the regulations for the installation of MAN indus-
trial gas engines for operation in enclosed areas. Ensure adequate ventilation.

D Smoking and naked flames are prohibited.

D Leaks in the gas supply system mean danger of explosion and these must be remedied
immediately.

D Fire extinguishers and other firefighting equipment must be on hand.

D Do not store combustible material in the engine room.

Conduct in the case of gas leaks

D Close the shutoff valve of the gas supply.

D Switch off the main switch of the electric system.
D Cordon off the danger zone. Ask persons who are not involved in the work to leave the danger zone.
D If gas is leaking, inform the relevant authorities immediately and initiate repairs.

Conduct in the event of fire

D Alert the fire brigade.

D Immediately assist any injured persons, call paramedics if necessary.
D In the case of a pure gas fire, do not extinguish the gas flame; if necessary, cool down the burning
object (e.g. by starving the fire of oxygen: close doors and windows).
Burning gas = controlled gas!
D Prevent the flames from spreading.
D If the flames spread to the surroundings, use a fire extinguisher.
D Stay calm!

10
 Fault table

Operating faults and possible causes

We recommend
A repair is only complete when both the damage that occurred and the possible causes have been elimin-
ated. Finding out the cause of damage is often more difficult than repairing the damage that occurred. We
therefore recommend that you obtain a precise description of the operating fault before removing and dis-
mantling components. Then use a process elimination (questions) to pinpoint the probable causes and in-
vestigate and eliminate these successively on the basis of the table and your own experience. This helps
to reduce repairs to the required scale and to counteract claims regarding “overeager” replacement of parts
and complaints about expensive work and down time.

Note:
The following list is conceived as an aid to memory for experts so that to causes of damage are overlooked
when dealing with faults. It is expected of experts that they are very familiar with the repair instructions for
the engine, but also with the engine operating instructions and “Fluids and lubricants for industrial gas en-
gines”.

11
 Fault table

1. Starter motor does not turn engine or only slowly (solenoid switch energises (“click” is audible)
2. Starter motor turns, engine does not turn
3. Starter motor turns engine, engine does not start / starts poorly
4. Ignition failure
5. . Irregular engine running
6. Engine stalls during operation, no longer starts
7. Engine “shakes”
8. Engine only runs at idle speed
9. Idle speed unstable
10. Engine does not reach its nominal speed
11. Engine does not reach its nominal power
12. Fuel consumption too high
13. Oil consumption too high
14. Engine too ”loud” / mechanical noise
15. Heavy blue smoke formation
16. Heavy white smoke formation
17. Exhaust temperature / exhaust back pressure too high (thermal overload)
18. Lubrication oil pressure too low
19. Temperature difference engine exit / engine entry too great
20. Coolant temperature too high
Possible causes
x Batteries discharged, battery cable connections loose or corroded, power circuit interrup-
ted
x Starter motor defective (carbon brushes loosened / worn, coil damaged, ground fault)
x Crankshaft drive blocked
x Ignition control unit defective
x Impulse sensor defective / gap incorrectly set
x x x Spark plug defective
x x x Ignition cable defective
x x x Ignition coil defective
o o x x x x Ignition point incorrectly set
x Throttle valve does not open / actuating rod jammed / setting unit de−energized or defec-
tive
x x Throttle valve not in full−load position / actuating rod jammed / throttle valve incorrectly
adjusted
x x Shut−off solenoid valve of gas supply closed / does not open
x x Zero pressure regulator of gas supply not correctly set or defective
x x x Gas metering valve defective
x x x x Gas / air mixture too rich or too lean
x x x x x Lambda control defective
x x Lack of compression, or more than 3 bar pressure difference between the individual cylin-
ders
x x x x Valve clearance not correct
x x Valve guides heavily worn
x x x x Valve seats leaking
x x x x x Piston rings heavily worn, broken (overpressure in the crankcase)
x x x x Air filter heavily soiled
x x x Charge mixture piping leaking
x Coolant entering combustion chamber (cylinder head gasket leaking)
x x Crankcase breather blocked
x Oil level in oil pan too high
x Safety valve in the oil circuit defective (does not close, spring fatigued or broken)
x Heavy bearing wear
x Oil pump heavily worn
x Safety valve in the oil circuit defective (does not open), oil lines / oil ducts blocked
x Unsuitable exhaust−gas piping, heat exchanger and catalytic converters with excessive
resistance
x Flow resistance of cooling system too great
x x Soiling of cooling system
x Coolant level too low, air in the coolant circuit
x Water pump too small or defective, or speed incorrectly set
x = likely to apply
o = might apply

12
 Fault table

1. Starter motor does not turn engine or only slowly (solenoid switch energises (“click” is audible)
2. Starter motor turns, engine does not turn
3. Starter motor turns engine, engine does not start / starts poorly
4. Ignition failure
5. . Irregular engine running
6. Engine stalls during operation, no longer starts
7. Engine “shakes”
8. Engine only runs at idle speed
9. Idle speed unstable
10. Engine does not reach its nominal speed
11. Engine does not reach its nominal power
12. Fuel consumption too high
13. Oil consumption too high
14. Engine too ”loud” / mechanical noise
15. Heavy blue smoke formation
16. Heavy white smoke formation
17. Exhaust temperature / exhaust back pressure too high (thermal overload)
18. Lubrication oil pressure too low
19. Temperature difference engine exit / engine entry too great
20. Coolant temperature too high
Possible causes
x x Coolant lines leaking, blocked or twisted
x Engine mounting unsuitable / worn

Note:
You will find instructions for troubleshooting and rectifying faults in the IC 500 ignition system in
the product information from Motortech GmbH, Hogrevestrasse 21, D−29223 Celle.

x = likely to apply
o = might apply

13
 General notes on engine overhaul

The service life of an engine is influenced by very different factors. It is therefore not possible to specify
certain fixed numbers of operating hours for general overhauls.

In our view, it is not necessary to open up and engine or perform a general overhaul
as long as the engine has good compression values and the following operating values have not changed
significantly in relation to the values measured on commissioning the engine:

D Exhaust temperature
D Coolant and lubricant temperature
D Oil pressure and oil consumption

The following criteria greatly influence the length of the engine service life:

D Correct power setting in accordance with conditions of use

D Technically correct installation
D Inspection if installation by authorised personnel
D Selection and quality of lubricants, fuel and coolant
according to publication “Fluids and lubricants for industrial gas engines”

14
Illustrations of E 2842 E 302 engine

15
 Engine lubrication diagrams

10

2
9

8 7 6 5

1 Rocker arm lubrication 6 Oil overpressure valve

2 Piston bolt lubrication 7 Oil cooler

3 Spray nozzles for piston cooling 8 Bypass valve

4 Camshaft bearing lubrication 9 Oil filter

5 Oil intake pipe 10 Main oil channels

16
 Engine lubrication diagrams

2 2

5 4 4 3

1 Oil lines to crankshaft and camshaft 4 Bore holes for conrod bearing lubrication

2 Bore holes to main bearing lubrication 5 Oil intake pipe

3 Oil pump with oil−pressure relief valve

17
 Cooling system diagrams

Cooling system with membrane expansion tank

4
5

6
7

1 9

10

1 Engine 6 Plate with 5x10 mm bore

2 Bleeder line ∅ 10 mm, 7 Membrane expansion tank 0.35 bar

flow rate 7 l/min to max. 10 l/min 8 Connecting line to intake side

3 Ventilation tank of coolant pump ∅25 mm

4 Automatic ventilation valve 9 Coolant outlet

5 Transmitter for coolant level 10 Coolant inlet

Overpressure safety valve: 3,5 bar

Operating pressure: min. 0,6 bar / max. 3,0 bar

18
 Cooling system diagrams

Cooling system in semi-open system

3
4

5
2

1 7

1 Engine

2 Bleeder line ∅ 10 mm, flow rate 7 l/min to max. 10 l/min

3 Filling cap with overpressure/vacuum valve 0,6 / −0,06 bar

4 Sensor for liquid level

5 Expansion tank

6 Connecting line to intake side of coolant pump ∅25 mm

7 Coolant outlet

8 Coolant inlet

19
 Engine timing

1 Intermediate gear 4 Drive gear, oil pump

2 Drive gear, camshaft 5 Oil pump supply gears

3 Crankshaft gear

20
Thank you very much
for your reading.
Please Click Here
Then Get More
Information.