Dividing Heads and Indexing Spacers

Download as pdf or txt
Download as pdf or txt
You are on page 1of 6

Dividing Heads and Indexing Spacers

Universal Dividing Heads


TURNING, MILLING & WORK HOLDING

• Designed for all types of gear cutting applications


• Precision dividing and spiral dividing (except type BS-0 and BS-1) are accomplished wirh accuracy and efficiency
• Center face can be tilted from a horizontal position of 90º down to -10º from vertical
• Scale graduated in 1º increments
• The center is built to the highest engineering standards
• Ratio of worm to gear is 40:1
• Units are factory inspected and tested
• Taper of center: B&S No. 10
• Center height (h2) maximum/minimum: 138mm/115mm
• Weight: 73 kg

A B H h a b g A1 a1 b1 g1 H1
Model (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ Code
Inch) Inch) Inch) Inch) Inch) Inch) Inch) Inch) Inch) Inch) Inch) Inch)
BS-2 365/14.37 272/10.71 236/9.29 132.7/5.22 213/8.39 134/5.28 16/0.63 194/7.64 177/6.97 125/4.92 16/0.63 147/5.79 277075

822

ENJOY QUALITY, VALUE AND BENEFITS - CALL KAR TODAY!

05_SectionC_pgs653-892+4_jun1512.indd 824 6/18/2012 10:52:28 AM


Dividing Heads and Indexing Spacers
Semi-Universal Dividing Heads

TURNING, MILLING & WORK HOLDING


• A simplified type of universal index center
• Can be used for either direct or indirect dividing
• Direct indexing plate with 24 holes enables dividing by 2, 3, 4, 6, 8, 12 and 24 divisions
• Three additional indexing plates included to provide the ability of indirect dividing of all divisions from 2 to 50 and also most common divisions
up to 380
• Taper of center: BS-0 – B&S No. 7, BS-1 – B&S No. 9
• Diameter of spindle hole: BS-0 – 18mm, BS-1 – 20mm
• Weight: BS-1 – 22 kg, BS-1 – 36 kg

A B C D E F G a b c d e f
Model (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ Code
Inch) Inch) Inch) Inch) Inch) Inch) Inch) Inch) Inch) Inch) Inch) Inch) Inch)
BS-0 189/7.44 160/6.30 100/3.94 173/6.81 16/0.63 91/3.58 140/5.51 90/3.54 105/4.13 16/0.63 100/3.94 166/6.54 127/5.00 277070
BS-1 293/11.34 210/8.27 128/5.04 220/8.66 16/0.63 114/4.49 156/6.14 108/4.25 134/5.28 16/0.63 128/5.04 184/7.24 150/5.91 277072

823

Toronto: 1-800-387-3127 Montréal: 1-800-363-7862 Edmonton: 1-866-440-4326 www.kar.ca sales@kar.ca

05_SectionC_pgs653-892+4_jun1512.indd 825 6/18/2012 10:52:28 AM


Dividing Heads and Indexing Spacers
Superior Universal Dividing Head
TURNING, MILLING & WORK HOLDING

• Can be used for simple dividing and also for producing worms, by changing gears and gear quadrant. A particular feature of the design is the
55.5mm through bore and the MT6 taper. The unit can also be tilted from 0-90º
• The spindle, worm and gear are made of high grade steel, hardened and ground for high accuracy and durability
• The tail stock is designed with dovetail construction for high rigidity and can be adjusted in either direction to achieve the correct alignment
• The worm and gear provide a reduction ratio of 40:1 and the unit is supplied with a double sided dividing plate
• Divisions on face A: 24, 25, 28, 30, 34, 37, 39, 41, 42 and 43
• Divisions on face B: 46, 47, 49, 51, 53, 54, 57, 58, 59, 62 and 66
• The change gears supplied are 24, 28, 32, 38, 40, 44, 48, 56, 64, 72, 86 and 100 teeth, providing a very wide and comprehensive range of
indexing
• Each universal dividing head is supplied complete with center, carrier change gear quadrant, set of change gears, tail stock and dividing plate

A B C D E F G H h J K L
Weight
Model (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ (mm/ Code
(kg)
Inch) Inch) Inch) Inch) Inch) Inch) Inch) Inch) Inch) Inch) Inch) Inch)
HCM-2 245/9.65 322/12.68 152/5.98 166/6.54 198/7.80 50/1.96 52/2.05 143/5.63 278/10.94 194/7.64 465/18.31 290/11.42 132 277105

Simple Indexing Spacer

• Mount on milling machines, drilling machines and other machine tools where an indexing facility is required
• Three-jaw chucks of both the CC-6” and the CC-8” models have a large through bore of 44mm and 63mm respectively
• Designed for use in horizontal or vertical positions
• The master indexing plate has 24 divisions and is permanently fixed inside the indexer
• Divisions of 2, 3, 4, 6, 8 and 12 can also be achieved by the use of the sub-plates, which can be installed quickly following these steps:
1. Open rear cover
2. Insert plate
3. Close cover
4. Loosen locking handle
5. Move dividing pin so as to separate it from the master plate
6. Turn the chuck. When the master plate and sub plate are aligned the pin will lock into the slot automatically
7. Fasten locking handle. Ready for machining

Diameter Diameter
g
Inner Outer of of
Dividable A B C D E a b h Guide Weight
Model Jaw Jaw Turret Chuck Code
Number (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) Block (kg)
(mm) (mm) Hole Hole
(mm)
(mm) (mm)
2, 3, 4, 6, 8,
CC-6 260 218 133 167 27 190 110 125 4-42 16 10-156 44 36 32 277080
12, 24
2, 3, 4, 6, 8,
CC-8 312 270 157 210 28 220 135 150 4-62 16 10-180 63 63 55 277082
12, 24

824

ENJOY QUALITY, VALUE AND BENEFITS - CALL KAR TODAY!

05_SectionC_pgs653-892+4_jun1512.indd 826 6/18/2012 10:52:29 AM


Dividing Heads and Indexing Spacers
Tail Stock for CC and CS Type Indexing Spacers

TURNING, MILLING & WORK HOLDING


• When using indexing spacers in a vertical position, these tail stocks can be used to support the work piece and ensure accurate alignment

Current Height
A B C E F Weight
Model Suitable for….. Max./Min. Code
(mm) (mm) (mm) (mm) (mm) (kg)
(mm)
TS-4 CC-6/CS-6 125 147 16 138/115 194 177 8.2 277084
TS-5 CC-8/CS-8 123 194 16 170/135 204 184 8.6 277086

Tail Stock for HHV Type Indexing Spacers

• This tail stock can be used for accurate centering when the rotary table is used in a vertical position

Current Height
A B C Weight
Model Suitable for….. Max./Min. Code
(mm) (mm) (mm) (kg)
(mm)
TS-1 HHV-200/HHV-250 230 247 210 190/110 13 277092
TS-2 HHV-300 230 280 210 220/140 15 277094
TS-3 HHV-350/HHV-400 230 330 210 264/184 17 277096

825

Toronto: 1-800-387-3127 Montréal: 1-800-363-7862 Edmonton: 1-866-440-4326 www.kar.ca sales@kar.ca

05_SectionC_pgs653-892+4_jun1512.indd 827 6/18/2012 10:52:29 AM


Dividing Heads and Indexing Spacers
Super Indexing Spacer
TURNING, MILLING & WORK HOLDING

• 3-jaw chuck mounted


• In addition to all of the features of the simple indexing spacer, the super indexing spacer incorporates a worm gear and is supplied with a face
plate. With the further addition of the optional dividing plate set, it can also be used as a dividing head.
• The worm gear is hardened and precision ground to minimize wear

Dividable A B C a b c d e f g h I j k Weight
Model Code
Number (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (kg)
2, 3, 4, 6, 8,
CS-6 250 224 190 190 140 117 420 97 65 16 130 198 84 18 35 277088
12, 24
2, 3, 4, 6, 8,
CS-8 310 295 212 225 160 142 460 108 76 16 160 245 95 18 70 277090
12, 24

Dividing Plate Sets


• The dividing plate set consists of two indexing plates, a sector and a handle with plunger
• Using this set, the indexing of 2 to 100 divisions can be attained quickly and accurately

Models: DP-1, DP-2, DP-3


Number of Holes:
DP-1....................... A Plate: 15, 16, 17, 18, 19, 20
B Plate: 21, 23, 27, 29, 31, 33
C Plate: 37, 39, 41, 43, 47, 49
DP-2 and DP-3....... A Plate: 26, 28, 30, 32, 34, 37, 38, 39, 41, 43, 44, 46, 47, 49, 51, 53, 57, 59
B Plate: 61, 63, 67, 69, 71, 73, 77, 79, 81, 83, 87, 89, 91, 93, 97, 99
Models: DP-4, DP-5
Number of Holes:
DP-4 and DP-5...... A Plate: 26, 28, 30, 32, 34, 37, 38, 39, 41, 43, 44, 46, 47, 49, 51, 53, 57, 59
B Plate: 61, 63, 67, 69, 71, 73, 77, 79, 81, 83, 87, 89, 91, 93, 97, 99
DP-4 for CS-6” Super Indexing Spacer
DP-5 for CS-8” Super Indexing Spacer

Inner Outer Groove Width


Dividing
Diameter Diameter in Handle Weight
Model Suitable for….. Plate Mount Code
of Sector Arm of Spring Clip Plate (kg)
(mm/Inch)
(mm/Inch) (mm/Inch) (mm/Inch)
DP-1 HHV-150/HHT-150 PCD, 32/1.26 21/0.83 18/0.71 9/0.35 2.5 277100
HHV-200/HHV-250/HHT-200/HHT-
DP-2 PCD (3 holes), 46/1.81 28.7/1.13 44/1.73 10/0.39 4 277102
250
HHV-300/HHV-350/HHV-400/HHT-
DP-3 PCD (3 holes), 46/1.81 28.7/1.13 44/1.73 10/0.39 4 277104
300/HHT-350
DP-4 CS-6 Super Indexing Spacer - - - - - 277101
DP-5 CS-8 Super Indexing Spacer - - - - - 277103

826

ENJOY QUALITY, VALUE AND BENEFITS - CALL KAR TODAY!

05_SectionC_pgs653-892+4_jun1512.indd 828 6/18/2012 10:52:30 AM


Dividing Heads and Indexing Spacers
Horizontal/Vertical Rotary Table

TURNING, MILLING & WORK HOLDING


The work table is graduated 360 degrees around it’s circumference and is driven by a precision worm and gear providing a 90:1
reduction ratio. One turn of the handle moves the table through four degrees. The dial is graduated in divisions of 1 minute and the
vernier scale allows readings down to 10 seconds.

• The worm is hardened and precision ground to minimize wear of the worm gear
• Both the upper and lower surface of the rotary plates are precision ground
• Operation and service manual included

OPTIONAL ACCESSORIES:
• Tail Stock
• Dividing Plate Set
• 3-Jaw Chuck

Base
D H K
Dimension Center Worm Gear Weight
Model Table Table Bolt Slots Code
AxB Sleeve Ratio (kg)
(mm) (mm) (mm)
(mm)
HHV-400 400 140 510 x 435 18 MT5 90:1 130 277110
HHV-150 150 92 220 x 160 18 MT2 90:1 12.5 277106
HHV-200 200 120 310 x 225 18 MT3 90:1 31 277107
HHV-250 250 120 320 x 280 18 MT3 90:1 48.5 277108
HHV-300 300 140 140 x 325 18 MT4 90:1 77 277109

827

Toronto: 1-800-387-3127 Montréal: 1-800-363-7862 Edmonton: 1-866-440-4326 www.kar.ca sales@kar.ca

05_SectionC_pgs653-892+4_jun1512.indd 829 6/18/2012 10:52:30 AM

You might also like