XT546-246-346 TERMINAL CONNECTIONS LOAD CONNECTIONS

selec Operating Instructions XT546 XT246 For load current less than 0.5A For bigger loads, use interposing
relay / contactor
OP288-V03

L START L N L N
+ 1 8 XT XT
L
1 11 6 COM - COM
+ 2 9 XT XT Contactor
N
- START LOAD
2 7 RST 3 10 RST C NO C NO
N R C
R C
NO1 NO2 4 11
3 8 MOV MOV
NO1 NO2 Snubber C Snubber
COM1 COM2
5 12
4 9
LOAD
COM1 COM2
6 13
96x96
72x72 5 12 10 NC1 7 14 FRONT PANEL DESCRIPTION
48x48 NC1 NC2 NC2

SPECIFICATIONS selec XT546

Display : Dual, 3 digit seven segment LED display XT346 COM

COM2
NO2 NC2 4
Supply : 85 to 270V AC, 50/60 Hz START RST H
R
24V AC / DC (Optional) 10 11 12 13 14 15 16 17 18
M 2
S
3
Operating : On Delay, Interval, Cyclic On first &
Modes Cyclic Off first
SET PROG LCK RST
Time Ranges : 9.99 / 99.9 / 999sec 1 2 3 4 5 6 7 8 9

9.59 min:sec, 99.9 / 999 min, L N NO1 NC1

9.59 hour:min, 99.9 / 999 hour On line Config Lock For Reset
COM1
Counting : Down Process Time Parameter name
Direction MECHANICAL INSTALLATION 2 Set Time Parameter setting
Relay Rating : 5A@250V AC / 28V DC For installing the Timer O/P Status ( Lit when O/P is ON )
3
Start Input : Pulse, Gate (Programmable) 1. Prepare the panel cutout with proper dimensions as shown below :
4 Time Range ( Blink in online mode )
Reset : On interruption of power, front panel reset & Outline Panel cutout
Dimensions (in mm) Dimensions (in mm)
terminal reset
Outputs : 2 ; 1 C/O (SPDT) PROTECTION LEVEL NOTE : Press + (LCK) key
together continuously for 3sec.
to enter into protection level.
Memory : 10 years
A Front bezel Side view D F Panel Cutout
Retention Use (any of 3) to select
Accuracy : Setting : ± 0.05% of set time or 50 msec Set time set time LOCK & UNLOCK
(Whichever is greater) B C G Lock Default : UNLOCK
E
Repeat : ± 0.05%
Temperature : Operating : 0 to 50OC DIM A B C D E F G
MODELS
Storage : -20 to 75OC Use (any of 3) to select
XT546 48 48 94 45 4 46 46 Config. config. LOCK & UNLOCK
Humidity : 95% RH XT246 72 72 83.7 67 10 69 69 Lock Default : UNLOCK
Housing : PC tinted black
XT346 96 96 73 90.5 10 92 92
Weight : XT546 : 140 gms
XT246 : 190 gms 2. Remove the clamp from the controller and push the controller
into the panel cutout. Insert the clamp from the rear side until the The unit will auto exit lock mode after 30sec. of key inactivity or by
XT346 : 240 gms main is securely fit into the panel. pressing + ( LCK ) keys continuously for 3sec. to exit the function.
Doc. Name : Operating/1112/XT546/246/346 OP288-V03 (Page 1 of 2)
CONFIGURATION INSTRUCTION RESET METHOD NOTE : Press + (RST) key MODE OF OPERATION
together continuously for
1. Enter configuration by pressing the key + (PROG) key together 1. On delay, Interval modes :
5sec. to enter into function.
for 3 sec.
Reset
2. Scroll various function ranges by pressing key(any of 3) The unit will auto exit Supply
3. Scroll various parameter by pressing the key. reset mode after 1sec. t : Set time Start
The unit will auto exit program mode after 30sec. of key inactivity Reset
or by pressing + (PROG) key together continuously for 3sec.
TO PROGRAM SET VALUE Note : Press key to change the
Output ON Delay
set value. The corresponding digit
t t t
Prompt only if configuration Lock will increment from 0 to 9 and then will roll over back to 0.
enabled in PROTECTION LEVEL Press key to store set value Output Interval
Lock code = 85 [Fixed] t t t
Set key Note : The decimal Point of 3rd digit Only if mode selected is on delay / Interval 2. Cyclic ON first, Cyclic OFF first modes :
blinks till correct Lock code entered.

Set 2nd digit

Set 1st digit

Set 3rd digit

Use key [any of 3] to scroll Supply
Output
through the various modes.
Modes t1 : ON time ; Start
Default : ON Delay t2 : OFF time
Reset

Use key [any of 3] to scroll Output Cyclic ON

Time NOTE : Press key to store set value. Decimal point of 3rd digit
through the various time range. t1 t2 t1 t2 t1 t2
Range blink still the storage of set value
Default : 99.9sec
Output Cyclic OFF
Only if mode selected is cyclic
t2 t1 t2 t1 t2 t1

Set 2nd digit

Set 1st digit

Set 3rd digit

Typical application of Continuous start and reset in On delay mode :
NOTE : This ! Use key [any of 3] to scroll
parameter is through the various ranges.
prompted ! In Cyclic ON function, also
t : Set time Supply
only if mode first OFF time is set and then
ON time is set. Start
selected is
! H, M, S indication will indicate
cyclic. the time range. Reset
NOTE : Press keys to register and move to next parameter
Output On delay

Set 2nd digit

Set 1st digit

Set 3rd digit

t t
Use key [any of 3] to
Start select gate or pulse. Typical application of Gate start
Default : Gate

Supply
Front Use key [any of 3] to rd
panel select yes or no
NOTE : Press key to store set value. Decimal point of 3 digit Gate
th = hold time ;
reset Default : Yes blinks till the storage of set value t1 + t2 = t Reset
NOTE : If the set value is 000 then timer must hold (not work). (set time)
All indications will be OFF. Output On delay
Use key [any of 3] to
Power The unit will auto exit set value mode after 30sec. of key inactivity
select yes or no t t1 th t2
on reset
Default : NO
USER GUIDE START : Pulse / Gate ( Specifications are subject to change, since development is a continuous process )
Use key [any of 3] to A) Pulse : Timing starts on momentary closure of switch connected
Default select yes or no between START and COMMON terminals. Selec Controls Pvt. Ltd.
Default : NO B) Gate : Timing starts at power on. When the START and COMMON Tel. No. : +91-22-40394200 / 40394202
terminal is closed timing freezes and it resumes only when Fax No. : +91-22-28471733 I Toll free : 1800 227 353
the shorting is opened. Website: www.selec.com I Email : [email protected]
Doc. Name : Operating/1112/XT546/246/346 OP288-V03 (Page 2 of 2)