RS–86 SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEM

DTC B1650/32 Occupant Classification System Malfunction

DESCRIPTION
The occupant classification system circuit consists of the center airbag sensor and the occupant
classification system.
RS When the center airbag sensor receives signals from the occupant classification ECU, it determines
whether or not the front passenger airbag, front seat side airbag RH and seat belt pretensioner RH should
be operated.
DTC B1650/32 is set when a malfunction is detected in the occupant classification system circuit.
DTC No. DTC Detection Conditions Trouble Areas
B1650/32 When one of following conditions is met: • Floor wire No. 2
• Occupant classification system malfunction • Occupant classification system
• Center airbag sensor detects line short signal, open • Center airbag sensor
signal, short to ground signal or short to B+ signal
from occupant classification system circuit for 2
seconds
• Center airbag sensor malfunction

WIRING DIAGRAM

Occupant Classification ECU Center Airbag Sensor

FSR+ FSP+

FSR- FSP-

C123527E09
 SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEM RS–87

INSPECTION PROCEDURE

1 CHECK DTC (OCCUPANT CLASSIFICATION ECU)

(a) Turn the power switch ON (IG), and wait for at least 10
seconds.
(b) Using the intelligent tester (with CAN VIM), check for
RS
DTCs of the occupant classification ECU (See page RS-
186).
OK:
DTC is not output.
OK GO TO DTC CHART

NG

2 CHECK DTC (CENTER AIRBAG SENSOR ASSEMBLY)

(a) Turn the power switch ON (IG), and wait for at least 60
seconds.
(b) Clear the DTCs (See page RS-38).
(c) Turn the power switch OFF.
(d) Turn the power switch ON (IG), and wait for at least 60
seconds.
Center Airbag (e) Check for DTCs (See page RS-38).
Occupant Sensor
Classification OK:
ECU DTC B1650/32 is not output.
HINT:
DTCs other than DTC B1650/32 may be output at this
time, but they are not related to this check.
DTC 32 NG USE SIMULATION METHOD TO CHECK
DLC3

CG TC

H100887E06

OK

3 CHECK CONNECTION OF CONNECTOR

(a) Turn the power switch OFF.

(b) Disconnect the cable from the negative (-) battery
terminal, and wait for at least 90 seconds.
(c) Check that the connectors are properly connected to the
center airbag sensor and the occupant classification
ECU.
OK:
Connectors are connected.
 RS–88 SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEM

NG CONNECT CONNECTOR

OK

4 CHECK FLOOR WIRE NO. 2 (OPEN)

RS
(a) Disconnect the connectors from the center airbag sensor
and the occupant classification ECU.
Floor Wire No. 2 (b) Using a service wire, connect terminals O4-8 (FSR+)
and O4-4 (FSR-) of connector C.
NOTICE:
C B
Do not forcibly insert a service wire into the
D A
terminals of the connector.
Center Airbag (c) Measure the resistance of the wire harness side
Occupant Sensor connector.
Classification
Standard resistance
ECU
Terminal Connection Specified Condition
A19-16 (FSP+) - A19-24 (FSP-) Below 1 !
Connector B
Connector C NG REPAIR OR REPLACE FLOOR WIRE NO. 2
A19
O4

FSR+ FSR- FSP- FSP+

C130791E02

OK
 SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEM RS–89

5 CHECK FLOOR WIRE NO. 2 (SHORT)

(a) Disconnect the service wire from connector C.

(b) Measure the resistance of the wire harness side
Floor Wire No. 2
connector.
Standard resistance RS
C B Terminal Connection Specified Condition
D A A19-16 (FSP+) - A19-24 (FSP-) 1 M! or higher

Center Airbag
Occupant Sensor NG REPAIR OR REPLACE FLOOR WIRE NO. 2
Classification
ECU

Connector B

A19

FSP- FSP+

C130792E02

OK

6 CHECK FLOOR WIRE NO. 2 (TO B+)

(a) Connect the cable to the negative (-) battery terminal,

and wait for at least 2 seconds.
(b) Turn the power switch ON (IG).
Floor Wire No. 2 (c) Measure the voltage of the wire harness side connector.
Standard voltage
C B
D A Terminal Connection Specified Condition
A19-16 (FSP+) - Body ground Below 1 V
Center Airbag
Occupant Sensor A19-24 (FSP-) - Body ground Below 1 V
Classification
ECU NG REPAIR OR REPLACE FLOOR WIRE NO. 2

Connector B

A19

FSP- FSP+

C130792E02

OK
 RS–90 SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEM

7 CHECK FLOOR WIRE NO. 2 (TO GROUND)

(a) Turn the power switch OFF.

(b) Disconnect the cable from the negative (-) battery
RS Floor Wire No. 2
terminal, and wait for at least 90 seconds.
(c) Measure the resistance of the wire harness side
connector.
C B
Standard resistance
D A
Terminal Connection Specified Condition
Center Airbag
Occupant A19-16 (FSP+) - Body ground 1 M! or higher
Sensor
Classification A19-24 (FSP-) - Body ground 1 M! or higher
ECU
NG REPAIR OR REPLACE FLOOR WIRE NO. 2
Connector B

A19

FSP- FSP+

C130792E02

OK

8 CHECK CENTER AIRBAG SENSOR ASSEMBLY

(a) Turn the power switch OFF.

(b) Disconnect the cable from the negative (-) battery
terminal, and wait for at least 90 seconds.
(c) Replace the center airbag sensor (see page RS-310).
HINT:
Perform the inspection using parts from a normal vehicle
Center Airbag when possible.
Occupant Sensor
Classification (d) Connect the connectors to the center airbag sensor.
ECU (e) Connect the cable to the negative (-) battery terminal,
and wait for at least 2 seconds.
(f) Turn the power switch ON (IG), and wait for at least 60
seconds.
(g) Clear the DTCs (see page RS-38).
DTC 32
DLC3 (h) Turn the power switch OFF.
(i) Turn the power switch ON (IG), and wait for at least 60
seconds.
(j) Check for DTCs (see page RS-38).
OK:
CG TC DTC B1650/32 is not output.
HINT:
H100887E07 DTCs other than DTC B1650/32 may be output at this
time, but they are not related to this check.
OK USE SIMULATION METHOD TO CHECK
 SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEM RS–91

NG

9 REPLACE OCCUPANT CLASSIFICATION ECU

(a) Turn the power switch OFF.

(b) Disconnect the cable from the negative (-) battery RS
terminal, and wait for at least 90 seconds.
(c) Replace the occupant classification ECU (see page SE-
4).
NEXT

10 PERFORM ZERO POINT CALIBRATION

(a) Connect the cable to the negative (-) battery terminal,

and wait for at least 2 seconds.
(b) Connect the intelligent tester to the DLC3.
(c) Turn the power switch ON (IG).
(d) Using the intelligent tester, perform the zero point
calibration (see page RS-178).
OK:
COMPLETED is displayed on the tester.
NEXT

11 PERFORM SENSITIVITY CHECK

(a) Using the intelligent tester, perform the sensitivity check

(see page RS-178).
Standard value:
27 to 33 kg (59.52 to 72.75 lb)
NEXT

END